RENESAS R8C/13

R8C/13 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
REJ03B0069-0120
Rev.1.20
Jan 27, 2006
1. Overview
This MCU is built using the high-performance silicon gate CMOS process using a R8C/Tiny Series CPU
core and is packaged in a 32-pin plastic molded LQFP. This MCU operates using sophisticated instructions
featuring a high level of instruction efficiency. With 1M bytes of address space, it is capable of executing
instructions at high speed.
The data flash ROM (2 KB X 2 blocks) is embedded.
1.1 Applications
Electric household appliance, office equipment, housing equipment (sensor, security), general industrial
equipment, audio, etc.
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 1 of 27
R8C/13 Group
1. Overview
1.2 Performance Overview
Table 1.1. lists the performance outline of this MCU.
Table 1.1 Performance outline
Item
Performance
CPU
Number of basic instructions 89 instructions
Minimum instruction execution time 50 ns (f(XIN) = 20 MHZ, VCC = 3.0 to 5.5 V)
100 ns (f(XIN) = 10 MHZ, VCC = 2.7 to 5.5 V)
Operating mode
Single-chip
Address space
1M bytes
Memory capacity
See Table 1.2.
Peripheral
Port
Input/Output: 22 (including LED drive port), Input: 2
function
LED drive port
I/O port: 8
Timer
Timer X: 8 bits x 1 channel, Timer Y: 8 bits x 1 channel,
Timer Z: 8 bits x 1 channel
(Each timer equipped with 8-bit prescaler)
Timer C: 16 bits x 1 channel
(Circuits of input capture and output compare)
Serial interface
•1 channel
Clock synchronous, UART
•1 channel
UART
A/D converter
10-bit A/D converter: 1 circuit, 12 channels
Watchdog timer
15 bits x 1 (with prescaler)
Reset start function selectable
Interrupt
Internal: 11 factors, External: 5 factors,
Software: 4 factors, Priority level: 7 levels
Clock generation circuit
2 circuits
•Main clock generation circuit (Equipped with a built-in
feedback resistor)
•On-chip oscillator (high-speed, low-speed)
On high-speed on-chip oscillator the frequency adjustment function is usable.
Oscillation stop detection function Main clock oscillation stop detection function
Voltage detection circuit
Included
Power on reset circuit
Included
Electrical
Supply voltage
VCC = 3.0 to 5.5V (f(XIN) = 20MHZ)
characteristics
VCC = 2.7 to 5.5V (f(XIN) = 10MHZ)
Power consumption
Typ.9 mA (VCC = 5.0V, (f(XIN) = 20MHZ)
Typ.5 mA (VCC = 3.0V, (f(XIN) = 10MHZ)
Typ.35 µA (VCC = 3.0V, Wait mode, Peripheral clock stops)
Typ.0.7 µA (VCC = 3.0V, Stop mode)
Flash memory Program/erase supply voltage VCC = 2.7 to 5.5 V
Program/erase endurance
10,000 times (Data flash)
1,000 times (Program ROM)
Operating ambient temperature
-20 to 85°C
-40 to 85°C (D-version)
Package
32-pin plastic mold LQFP
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 2 of 27
R8C/13 Group
1. Overview
1.3 Block Diagram
Figure 1.1 shows this MCU block diagram.
8
8
I/O port
Port P0
1
5
Port P3
Port P1
2
Port P4
Peripheral functions
Timer
Timer X (8 bits)
Timer Y (8 bits)
Timer Z (8 bits)
Timer C (16 bits)
A/D converter
(10 bits ✕ 12 channels)
System clock generator
UART or Clock synchronous
serial I/O
(8 bits ✕ 1 channel)
XIN-XOUT
High-speed on-chip oscillator
Low-speed on-chip oscillator
UART
(8 bits ✕ 1 channel)
Memory
R8C/Tiny Series CPU core
Watchdog timer
(15 bits)
R0H
R1H
R0L
R1L
R2
R3
SB
ISP
INTB
A0
A1
FB
(1)
ROM
USP
RAM
(2)
PC
FLG
Multiplier
NOTES:
1. ROM size depends on MCU type.
2. RAM size depends on MCU type.
Figure 1.1 Block Diagram
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 3 of 27
R8C/13 Group
1. Overview
1.4 Product Information
Table 1.2 lists the product information.
Table 1.2 Product Information
As of January 2006
ROM capacity
Type No.
Remarks
Program ROM
Data flash
RAM capacity
R5F21132FP
8K bytes
2K bytes x 2
512 bytes
PLQP0032GB-A Flash memory version
R5F21133FP
12K bytes
2K bytes x 2
768 bytes
PLQP0032GB-A
R5F21134FP
16K bytes
2K bytes x 2
1K bytes
PLQP0032GB-A
R5F21132DFP
8K bytes
2K bytes x 2
512 bytes
PLQP0032GB-A D version
R5F21133DFP
12K bytes
2K bytes x 2
768 bytes
PLQP0032GB-A
R5F21134DFP
16K bytes
2K bytes x 2
1K bytes
PLQP0032GB-A
Type No. R 5 F
Package type
21 13 4 D FP
Package type:
FP : PLQP0032GB-A
Classification:
D: Operating ambient temperature –40 °C to 85 °C
No symbol: Operating ambient temperature –20 °C to 85 °C
ROM capacity:
2 : 8 KBytes.
3 : 12 KBytes.
4 : 16 KBytes.
R8C/13 group
R8C/Tiny series
Memory type:
F: Flash memory version
Renesas MCU
Renesas semiconductors
Figure 1.2 Type No., Memory Size, and Package
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 4 of 27
R8C/13 Group
1. Overview
1.5 Pin Assignments
Figure 1.3 shows the pin configuration (top view).
P30/CNTR0/CMP10
AVSS
P31/TZOUT/CMP11
AVCC/VREF
P32/INT2/CNTR1/CMP12
P33/INT3/ TCIN
P07/AN0
IVCC(3)
PIN Assignments (top view)
24 23 22 21 20 19 18 17
P06/AN1
P05/AN2
P04/AN3
MODE
P03/AN4
P02/AN5
P01/AN6
P00/AN7/TxD11
25
26
27
28
29
30
31
32
16
15
14
13
12
11
10
9
R8C/13 Group
P45/INT0
P10/KI0/AN8/CMP00
P11/KI1/AN9/CMP01
P12/KI2/AN10/CMP02
P13/KI3/AN11
P14/TxD0
P15/RxD0
P16/CLK0
RESET
XOUT/P47 (1)
VSS
XIN/P46
VC C
P17/INT1/CNTR0
P37/TxD10/RxD1
CNVSS
1 2 3 4 5 6 7 8
NOTES:
1. P47 functions only as an input port.
2. When using On-chip debugger, do not use P00/AN7/TxD11
and P37/TxD10/RxD1 pins.
3. Do not connect IVcc to Vcc.
Package: PLQP0032GB-A (32P6U-A)
Figure 1.3 Pin Assignments (Top View)
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 5 of 27
R8C/13 Group
1. Overview
1.6 Pin Description
Table 1.3 shows the pin description
Table 1.3 Pin description
Signal name
Power supply
input
IVcc
Pin name
Vcc,
Vss
IVcc
I/O type
O
Analog power
supply input
AVcc, AVss
I
Power supply input pins for A/D converter. Connect the
AVcc pin to Vcc. Connect the AVss pin to Vss. Connect a
capacitor between pins AVcc and AVss.
Reset input
CNVss
MODE
Main clock input
RESET
CNVss
MODE
XIN
I
I
I
I
I
___________
Function
Apply 2.7 V to 5.5 V to the Vcc pin. Apply 0 V to the
Vss pin.
This pin is to stabilize internal power supply.
Connect this pin to Vss via a capacitor (0.1 µF).
Do not connect to Vcc.
INT interrupt input INT
0 to_____
INT3
_____
Key input interrupt KI0 to KI3
input
Timer X
CNTR
0
__________
CNTR0
Timer Y
CNTR1
Timer Z
TZOUT
Timer C
TCIN
CMP00 to CMP02,
CMP10 to CMP12
Serial interface
CLK0
RxD0, RxD1
TxD0, TxD10,
TxD11
Reference voltage VREF
input
A/D converter
AN0 to AN11
I/O port
P00 to P07,
P10 to P17,
P30 to P33, P37,
P45
I
I
Input “L” on this pin resets the MCU.
Connect this pin to Vss via a resistor.
Connect this pin to Vcc via a resistor.
These pins are provided for the main clock generating circuit I/O. Connect a ceramic resonator or a crystal oscillator between the XIN and XOUT pins. To use
an externally derived clock, input it to the XIN pin and
leave
the XOUT pin open.
______
INT interrupt input pins.
Key input interrupt pins.
I/O
O
I/O
O
I
O
Timer X I/O pin
Timer X output pin
Timer Y I/O pin
Timer Z output pin
Timer C input pin
The timer C output pins
I/O
I
O
Transfer clock I/O pin.
Serial data input pins.
Serial data output pins.
I
Reference voltage input pin for A/D converter. Connect the VREF pin to Vcc.
Analog input pins for A/D converter
These are 8-bit CMOS I/O ports. Each port has an I/O
select direction register, allowing each pin in that port
to be directed for input or output individually.
Any port set to input can select whether to use a pullup resistor or not by program.
P10 to P17 also function as LED drive ports.
Input port
I
Main clock output XOUT
_____
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
_______
O
_______
P46, P47
page 6 of 27
I
I/O
Port for input-only
R8C/13 Group
2. Central Processing Unit (CPU)
2. Central Processing Unit (CPU)
Figure 2.1 shows the CPU Register. The CPU contains 13 registers. Of these, R0, R1, R2, R3, A0, A1 and
FB comprise a register bank. Two sets of register banks are provided.
b31
b15
b8 b7
b0
R2
R0H(High-order of R0) R0L(Low-order of R0)
R3
R1H(High-order of R1) R1L(Low-order of R1)
R2
Data registers(1)
R3
A0
b19
A1
Address registers(1)
FB
Frame base registers(1)
b15
b0
INTBH
INTBL
Interrupt table register
The 4-high order bits of INTB are INTBH and
the 16-low bits of INTB are INTBL.
b19
b0
PC
Program counter
b15
b0
USP
User stack pointer
ISP
Interrupt stack pointer
SB
Static base register
b15
b0
FLG
b15
b8
IPL
b7
U I
Flag register
b0
O B S Z D C
Carry flag
Debug flag
Zero flag
Sign flag
Register bank select flag
Overflow flag
Interrupt enable flag
Stack pointer select flag
Reserved bit
Processor interrupt priority level
Reserved bit
NOTES:
1. A register bank comprises these registers. Two sets of register banks are provided
Figure 2.1 CPU Register
2.1 Data Registers (R0, R1, R2 and R3)
R0 is a 16-bit register for transfer, arithmetic and logic operations. The same applies to R1 to R3. The R0
can be split into high-order bit (R0H) and low-order bit (R0L) to be used separately as 8-bit data registers.
The same applies to R1H and R1L as R0H and R0L. R2 can be combined with R0 to be used as a 32-bit
data register (R2R0). The same applies to R3R1 as R2R0.
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 7 of 27
R8C/13 Group
2. Central Processing Unit (CPU)
2.2 Address Registers (A0 and A1)
A0 is a 16-bit register for address register indirect addressing and address register relative addressing.
They also are used for transfer, arithmetic and logic operations. The same applies to A1 as A0. A0 can be
combined with A0 to be used as a 32-bit address register (A1A0).
2.3 Frame Base Register (FB)
FB is a 16-bit register for FB relative addressing.
2.4 Interrupt Table Register (INTB)
INTB is a 20-bit register indicates the start address of an interrupt vector table.
2.5 Program Counter (PC)
PC, 20 bits wide, indicates the address of an instruction to be executed.
2.6 User Stack Pointer (USP) and Interrupt Stack Pointer (ISP)
The stack pointer (SP), USP and ISP, are 16 bits wide each.
The U flag of FLG is used to switch between USP and ISP.
2.7 Static Base Register (SB)
SB is a 16-bit register for SB relative addressing.
2.8 Flag Register (FLG)
FLG is a 11-bit register indicating the CPU state.
2.8.1 Carry Flag (C)
The C flag retains a carry, borrow, or shift-out bit that has occurred in the arithmetic logic unit.
2.8.2 Debug Flag (D)
The D flag is for debug only. Set to “0”.
2.8.3 Zero Flag (Z)
The Z flag is set to “1” when an arithmetic operation resulted in 0; otherwise, “0”.
2.8.4 Sign Flag (S)
The S flag is set to “1” when an arithmetic operation resulted in a negative value; otherwise, “0”.
2.8.5 Register Bank Select Flag (B)
The register bank 0 is selected when the B flag is “0”. The register bank 1 is selected when this flag is
set to “1”.
2.8.6 Overflow Flag (O)
The O flag is set to “1” when the operation resulted in an overflow; otherwise, “0”.
2.8.7 Interrupt Enable Flag (I)
The I flag enables a maskable interrupt.
An interrupt is disabled when the I flag is set to “0”, and are enabled when the I flag is set to “1”. The
I flag is set to “0” when an interrupt request is acknowledged.
2.8.8 Stack Pointer Select Flag (U)
ISP is selected when the U flag is set to “0”, USP is selected when the U flag is set to “1”.
The U flag is set to “0” when a hardware interrupt request is acknowledged or the INT instruction of
software interrupt numbers 0 to 31 is executed.
2.8.9 Processor Interrupt Priority Level (IPL)
IPL, 3 bits wide, assigns processor interrupt priority levels from level 0 to level 7.
If a requested interrupt has greater priority than IPL, the interrupt is enabled.
2.8.10 Reserved Bit
When write to this bit, set to “0”. When read, its content is indeterminate.
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 8 of 27
R8C/13 Group
3. Memory
3. Memory
Figure 3.1 is a memory map of this MCU. This MCU provides 1-Mbyte address space from addresses
0000016 to FFFFF16.
The internal ROM (program ROM) is allocated lower addresses beginning with address 0FFFF16. For
example, a 16-Kbyte internal ROM is allocated addresses from 0C00016 to 0FFFF16.
The fixed interrupt vector table is allocated addresses 0FFDC16 to 0FFFF16. They store the starting
address of each interrupt routine.
The internal ROM (data flash) is allocated addresses from 0200016 to 02FFF16.
The internal RAM is allocated higher addresses beginning with address 0040016. For example, a 1-Kbyte
internal RAM is allocated addresses 0040016 to 007FF16. The internal RAM is used not only for storing
data, but for calling subroutines and stacks when interrupt request is acknowledged.
Special function registers (SFR) are allocated addresses 0000016 to 002FF16. The peripheral function
control registers are located them. All addresses, which have nothing allocated within the SFR, are reserved area and cannot be accessed by users.
0000016
SFR
(See Chapter 4 for details.)
002FF16
0040016
Internal RAM
0XXXX16
0200016
Internal ROM
(data flash)(1)
0FFDC16
Undefined instruction
Overflow
BRK instruction
Address match
Single step
02FFF16
Watchdog timer,Oscillation stop detection,Voltage detection
0YYYY16
Internal ROM
(program ROM)
(Reserved)
(Reserved)
Reset
0FFFF16
0FFFF16
Expansion area
FFFFF16
NOTES:
1. The data flash block A (2K bytes) and block B (2K bytes) are shown.
2. Blank spaces are reserved. No access is allowed.
Internal ROM
Internal RAM
Type name
Address 0YYYY16
Address 0XXXX16
Size
Size
R5F21134FP, R5F21134DFP
16K bytes
0C00016
1K bytes
R5F21133FP, R5F21133DFP
12K bytes
0D00016
768 bytes
006FF16
R5F21132FP, R5F21132DFP
8K bytes
0E00016
512 bytes
005FF16
Figure 3.1 Memory Map
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 9 of 27
007FF16
R8C/13 Group
4. Special Function Register (SFR)
4. Special Function Register (SFR)
SFR(Special Function Register) is the control register of peripheral functions. Tables 4.1 to 4.4 list the SFR
information
Table 4.1 SFR Information(1)(1)
Register
Address
Symbol
After reset
000016
000116
000216
000316
000416
000516
000616
000716
000816
000916
000A16
000B16
000C16
000D16
000E16
000F16
001016
Processor mode register 0 (1)
Processor mode register 1
System clock control register 0
System clock control register 1
High-speed on-chip oscillator control register 0
Address match interrupt enable register
Protect register
High-speed on-chip oscillator control register 1
Oscillation stop detection register
Watchdog timer reset register
Watchdog timer start register
Watchdog timer control register
Address match interrupt register 0
PM0
PM1
CM0
CM1
HR0
AIER
PRCR
HR1
OCD
WDTR
WDTS
WDC
RMAD0
0016
0016
011010002
001000002
0016
XXXXXX002
00XXX0002
4016
000001002
XX16
XX16
000111112
0016
0016
X016
Address match interrupt register 1
RMAD1
0016
0016
X016
Voltage detection register 1(2)
Voltage detection register 2 (2)
VCR1
VCR2
000010002
0016 (3)
100000002(4)
INT0 input filter select register
Voltage detection interrupt register (2)
INT0F
D4INT
XXXXX0002
0016 (3)
010000012(4)
001116
001216
001316
001416
001516
001616
001716
001816
001916
001A16
001B16
001C16
001D16
001E16
001F16
002016
002116
002216
002316
002416
002516
002616
002716
002816
002916
002A16
002B16
002C16
002D16
002E16
002F16
003016
003116
003216
003316
003416
003516
003616
003716
003816
003916
003A16
003B16
003C16
003D16
003E16
003F16
X : Undefined
NOTES:
1. Blank spaces are reserved. No access is allowed.
2. Software reset or the watchdog timer reset does not affect this register.
3. Owing to Reset input.
4. In the case of RESET pin = H retaining.
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 10 of 27
R8C/13 Group
4. Special Function Register (SFR)
Table 4.2 SFR Information(2)(1)
Register
Symbol
After reset
Key input interrupt control register
AD conversion interrupt control register
KUPIC
ADIC
XXXXX0002
XXXXX0002
Compare 1 interrupt control register
UART0 transmit interrupt control register
UART0 receive interrupt control register
UART1 transmit interrupt control register
UART1 receive interrupt control register
CMP1IC
S0TIC
S0RIC
S1TIC
S1RIC
INT2IC
TXIC
TYIC
TZIC
INT1IC
INT3IC
TCIC
CMP0IC
INT0IC
XXXXX0002
XXXXX0002
XXXXX0002
XXXXX0002
XXXXX0002
XXXXX0002
XXXXX0002
XXXXX0002
XXXXX0002
XXXXX0002
XXXXX0002
XXXXX0002
XXXXX0002
XX00X0002
Address
004016
004116
004216
004316
004416
004516
004616
004716
004816
004916
004A16
004B16
004C16
004D16
004E16
004F16
005016
005116
005216
005316
005416
005516
005B16
INT2 interrupt control register
Timer X interrupt control register
Timer Y interrupt control register
Timer Z interrupt control register
INT1 interrupt control register
INT3 interrupt control register
Timer C interrupt control register
005C16
Compare 0 interrupt control register
005D16
INT0 interrupt control register
005616
005716
005816
005916
005A16
005E16
005F16
006016
006116
006216
006316
006416
006516
006616
006716
006816
006916
006A16
006B16
006C16
006D16
006E16
006F16
007016
007116
007216
007316
007416
007516
007616
007716
007816
007916
007A16
007B16
007C16
007D16
007E16
007F16
X : Undefined
NOTES:
1. Blank spaces are reserved. No access is allowed.
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 11 of 27
R8C/13 Group
4. Special Function Register (SFR)
Table 4.3 SFR Information(3)(1)
Register
Timer Y, Z mode register
Prescaler Y register
Timer Y secondary register
Timer Y primary register
Timer Y, Z waveform output control register
Prescaler Z register
Timer Z secondary register
Timer Z primary register
Symbol
TYZMR
PREY
TYSC
TYPR
PUM
PREZ
TZSC
TZPR
0016
FF16
FF16
FF16
0016
FF16
FF16
FF16
Timer Y, Z output control register
Timer X mode register
Prescaler X register
Timer X register
Count source set register
TYZOC
TXMR
PREX
TX
TCSS
0016
0016
FF16
FF16
0016
Timer C register
TC
0016
0016
External input enable register
INTEN
0016
Key input enable register
KIEN
0016
Timer C control register 0
Timer C control register 1
Capture, compare 0 register
TCC0
TCC1
TM0
009E16
Compare 1 register
TM1
009F16
00A016
UART0 transmit/receive mode register
U0MR
U0BRG
U0TB
0016
0016
0016
0016(2)
FF16
FF16
0016
XX16
XX16
X X1 6
000010002
000000102
XX16
XX16
0016
XX16
XX16
X X1 6
000010002
000000102
XX16
X X1 6
0016
Address
008016
008116
008216
008316
008416
008516
008616
008716
After reset
008816
008916
008A16
008B16
008C16
008D16
008E16
008F16
009016
009116
009216
009316
009416
009516
009616
009716
009816
009916
009A16
009B16
009C16
009D16
00A116
00A216
UART0 bit rate register
UART0 transmit buffer register
00A316
00A516
UART0 transmit/receive control register 0
UART0 transmit/receive control register 1
00A616
UART0 receive buffer register
00A416
U0C0
U0C1
U0RB
00A716
00A816
UART1 transmit/receive mode register
00A916
UART1 bit rate register
UART1 transmit buffer register
00AA16
U1MR
U1BRG
U1TB
00AB16
00AD16
UART1 transmit/receive control register 0
UART1 transmit/receive control register 1
00AE16
UART1 receive buffer register
U1C0
U1C1
U1RB
UART transmit/receive control register 2
UCON
00AC16
00AF16
00B016
00B116
00B216
00B316
00B416
00B516
00B616
00B716
00B816
00B916
00BA16
00BB16
00BC16
00BD16
00BE16
00BF16
X : Undefined
NOTES:
1. Blank spaces are reserved. No access is allowed.
2. When output compare mode (the TCC13 bit in the TCC1 register = 1) is selected, the value after reset is set to “FFFF16”.
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 12 of 27
R8C/13 Group
4. Special Function Register (SFR)
Table 4.4 SFR Information(4)(1)
Register
Address
AD register
Symbol
AD
AD control register 2
ADCON2
0016
AD control register 0
AD control register 1
ADCON0
ADCON1
00000XXX2
0016
Port P0 register
Port P1 register
Port P0 direction register
Port P1 direction register
P0
P1
PD0
PD1
XX16
XX16
0016
0016
Port P3 register
P3
XX16
Port P3 direction register
Port P4 register
PD3
P4
0016
XX16
Port P4 direction register
PD4
0016
00FF16
Pull-up control register 0
Pull-up control register 1
Port P1 drive capacity control register
Timer C output control register
PUR0
PUR1
DRR
TCOUT
00XX00002
XXXXXX0X2
0016
0016
01B316
Flash memory control register 4
FMR4
010000002
Flash memory control register 1
FMR1
1000000X2
01B716
Flash memory control register 0
FMR0
000000012
0FFFF16
Option function select register
OFS
00C016
00C116
After reset
XX16
X X1 6
00C216
00C316
00C416
00C516
00C616
00C716
00C816
00C916
00CA16
00CB16
00CC16
00CD16
00CE16
00CF16
00D016
00D116
00D216
00D316
00D416
00D516
00D616
00D716
00D816
00D916
00DA16
00DB16
00DC16
00DD16
00DE16
00DF16
00E016
00E116
00E216
00E316
00E416
00E516
00E616
00E716
00E816
00E916
00EA16
00EB16
00EC16
00ED16
00EE16
00EF16
00F016
00F116
00F216
00F316
00F416
00F516
00F616
00F716
00F816
00F916
03FA16
00FB16
00FC16
00FD16
00FE16
01B416
01B516
01B616
(2)
(Note 2)
X : Undefined
NOTES:
1. Blank columns, 010016 to 01B216 and 01B816 to 02FF16 are all reserved. No access is allowed.
2. The watchdog timer control bit is assigned. Refer to "Figure11.2 OFS, WDC, WDTR and WDTS registers" of Hardware Manual for details
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 13 of 27
R8C/13 Group
5. Electrical Characteristics
5. Electrical Characteristics
Table 5.1 Absolute Maximum Ratings
Condition
Rated value
Unit
VCC
Symbol
Supply voltage
Parameter
VCC=AVCC
-0.3 to 6.5
V
AVCC
Analog supply voltage
VCC=AVCC
-0.3 to 6.5
V
VI
Input voltage
-0.3 to VCC+0.3
V
VO
Output voltage
-0.3 to VCC+0.3
V
Pd
Power dissipation
300
mW
Topr
Operating ambient temperature
-20 to 85 / -40 to 85 (D version)
C
Tstg
Storage temperature
Topr=25 C
C
-65 to 150
Table 5.2 Recommended Operating Conditions
Symbol
Parameter
VCC
AVcc
Supply voltage
Analog supply voltage
Vss
Supply voltage
Conditions
Min.
Standard
Typ.
2.7
Max.
5.5
VCC(3)
0
Unit
V
V
V
V
AVss
Analog supply voltage
VIH
"H" input voltage
0.8VCC
VCC
V
VIL
"L" input voltage
0
0.2VCC
V
-60.0
mA
-10.0
mA
- 5 .0
mA
60
mA
10
mA
30
mA
10
mA
mA
mA
mA
MHz
MHz
I OH (peak)
Sum of all pins' IOH
"H" peak all
output currents (peak)
"H" peak output current
I OH (avg)
"H" average output current
I OL (sum)
Sum of all pins' IOL
"L" peak all
output currents (peak)
"L" peak output Except P10 to P17
current
P10 to P17
I OH (sum)
I OL (peak)
I OL (avg)
f (XIN)
"L" average
output current
0
Drive ability HIGH
Drive ability LOW
Except P10 to P17
P10 to P17
Drive ability HIGH
Drive ability LOW
Main clock input oscillation frequency 3.0V ≤ Vcc ≤ 5.5V
2.7V ≤ Vcc < 3.0V
0
0
NOTES:
1. VCC = AVCC = 2.7 to 5.5V at Topr = -20 to 85 °C / -40 to 85 °C, unless otherwise specified.
2. The typical values when average output current is 100ms.
3. Hold Vcc=AVcc.
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 14 of 27
5
15
5
20
10
R8C/13 Group
5. Electrical Characteristics
Table 5.3 A/D Conversion Characteristics
Symbol
Parameter
–
Resolution
–
Absolute
accuracy
RLADDER
tCONV
VREF
VIA
Ladder resistance
Conversion time
Measuring condition
Standard
Unit
Min. Typ. Max.
Vref =VCC
10
Bit
10 bit mode
øAD=10 MHz, Vref=Vcc=5.0V
±3
LSB
8 bit mode
øAD=10 MHz, Vref=Vcc=5.0V
±2
LSB
10 bit mode
øAD=10 MHz, Vref=Vcc=3.3V(3)
±5
LSB
8 bit mode
Vref=Vcc=3.3V(3)
±2
LSB
kΩ
10 bit mode
8 bit mode
øAD=10 MHz,
VREF=VCC
10
øAD=10 MHz, Vref=Vcc=5.0V
3.3
2.8
øAD=10 MHz, Vref=Vcc=5.0V
Reference voltage
Analog input voltage
40
µs
µs
V
VCC(4)
0
Vref
V
0.25
10
MHz
1.0
10
NOTES:
1. VCC=AVCC=2.7 to 5.5V at Topr = -20 to 85 °C / -40 to 85 °C, unless otherwise specified.
2. If fAD exceeds 10 MHz more, divide the fAD and hold A/D operating clock frequency (ØAD) 10 MHz or below.
3. If the AVcc is less than 4.2V, divide the fAD and hold A/D operating clock frequency (ØAD) fAD/2 or below.
4. Hold Vcc=Vref.
MHz
–
A/D operating
Without sample & hold
clock frequency(2) With sample & hold
P0
P1
P2
P3
P4
Figure 5.1 Port P0 to P4 measurement circuit
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 15 of 27
30pF
R8C/13 Group
5. Electrical Characteristics
Table 5.4 Flash Memory (Program ROM) Electrical Characteristics
Symbol
Parameter
Measuring condition
Min.
Standard
Typ.
Max
Unit
times
–
–
Program/Erase endurance(2)
Byte program time
50
µs
–
Block erase time
0.4
s
td(SR-ES)
1000(3)
8
Time delay from Suspend Request until Erase Suspend
ms
–
Erase Suspend Request Interval
10
–
Program, Erase Voltage
2.7
5.5
V
–
–
Read Voltage
2.7
5.5
60
V
–
Data hold time(7)
0
Program, Erase Temperature
Ambient temperature =
55 °C
20
ms
°C
year
NOTES:
1. Referenced to VCC=AVcc=2.7 to 5.5V at Topr = 0°C to 60°C unless otherwise specified.
2. Definition of Program/Erase
The endurance of Program/Erase shows a time for each block.
If the program/erase number is “n” (n = 1000, 10000), “n” times erase can be performed for each block.
For example, if performing one-byte write to the distinct addresses on Block A of 2K-byte block 2048 times and then
erasing that block, the number of Program/Erase cycles is one time.
However, performing multiple writes to the same address before an erase operation is prohibited (overwriting
prohibited).
3. Numbers of Program/Erase cycles for which all electrical characteristics is guaranteed.
4. To reduce the number of Program/Erase cycles, a block erase should ideally be performed after writing in series as
many distinct addresses (only one time each) as possible. If programming a set of 16 bytes, write up to 128 sets and
then erase them one time. This will result in ideally reducing the number of Program/Erase cycles. Additionally,
averaging the number of Program/Erase cycles for Block A and B will be more effective. It is important to track the total
number of block erases and restrict the number.
5. If error occurs during block erase, attempt to execute the clear status register command, then the block erase
command at least three times until the erase error disappears.
6. Customers desiring Program/Erase failure rate information should contact their Renesas technical support representative.
7. The data hold time includes time that the power supply is off or the clock is not supplied.
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 16 of 27
R8C/13 Group
5. Electrical Characteristics
Table 5.5 Flash Memory (Data flash Block A, Block B) Electrical Characteristics(4)
Symbol
Parameter
Standard
Min.
Typ.
Measuring condition
Program/Erase endurance(2)
–
Byte program time(program/erase endurance
≤1000 times)
50
–
Byte program time(program/erase endurance
>1000 times)
65
–
Block erase time(program/erase endurance
≤1000 times)
Block erase time(program/erase endurance
>1000 times)
0.2
td(SR-ES)
–
–
–
–
–
10000(3)
400
µs
µs
9
0.3
Time delay from Suspend Request until Erase Suspend
Unit
times
–
–
Max
s
s
8
ms
10
Erase Suspend Request Interval
Program, Erase Voltage
2.7
5.5
ms
V
Read Voltage
2.7
5.5
V
-20(-40)(8)
Program/Erase Temperature
Data hold time(9)
Ambient temperature =
55 °C
20
85
°C
year
NOTES:
1. Referenced to VCC=AVcc=2.7 to 5.5V at Topr = -20°C to 85°C / -40°C to 85°C unless otherwise specified.
2. Definition of Program/Erase
The endurance of Program/Erase shows a time for each block.
If the program/erase number is “n” (n = 1000, 10000), “n” times erase can be performed for each block.
For example, if performing one-byte write to the distinct addresses on Block A of 2K-byte block 2048 times and then
erasing that block, the number of Program/Erase cycles is one time.
However, performing multiple writes to the same address before an erase operation is prohibited (overwriting
prohibited).
3. Numbers of Program/Erase cycles for which all electrical characteristics is guaranteed.
4. Table 5.5 applies for Block A or B when the Program/Erase cycles are more than 1000. The byte program time up to
1000 cycles are the same as that of the program area (see Table 5.4).
5. To reduce the number of Program/Erase cycles, a block erase should ideally be performed after writing in series as
many distinct addresses (only one time each) as possible. If programming a set of 16 bytes, write up to 128 sets and
then erase them one time. This will result in ideally reducing the number of Program/Erase cycles. Additionally,
averaging the number of Program/Erase cycles for Block A and B will be more effective. It is important to track the total
number of block erases and restrict the number.
6. If error occurs during block erase, attempt to execute the clear status register command, then the block erase
command at least three times until the erase error disappears.
7. Customers desiring Program/Erase failure rate information should contact their Renesas technical support representative.
8. -40 °C for D version.
9. The data hold time includes time that the power supply is off or the clock is not supplied.
Erase-suspend request
(interrupt request)
FMR46
td(SR-ES)
Figure 5.2 Time delay from Suspend Request until Erase Suspend
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 17 of 27
R8C/13 Group
5. Electrical Characteristics
Table 5.6 Voltage Detection Circuit Electrical Characteristics
Symbol
Vdet
Measuring condition
Parameter
Voltage detection level
Min.
Voltage detection interrupt request generating time(2)
Microcomputer operation voltage minimum value
Unit
V
µs
nA
600
VC27=1, VCC=5.0V
Vccmin
4.3
40
Voltage detection circuit self consumption current
Waiting time until voltage detection circuit operation starts(3)
Max.
3.8
3.3
td(E-A)
Standard
Typ.
20
µs
V
2.7
NOTES:
1. The measuring condition is Vcc=AVcc=2.7V to 5.5V and Topr=-40°C to 85°C.
2. This shows the time until the voltage detection interrupt request is generated since the voltage passes Vdet.
3. This shows the required time until the voltage detection circuit operates when setting to "1" again after setting the VC27 bit in the VCR2
register to “0”.
Table 5.7 Reset Circuit Electrical Characteristics (When Using Hardware Reset 2(1, 3))
Symbol
Vpor2
Measuring condition
Parameter
Power-on reset valid voltage
tW(Vpor2Supply voltage rising time when power-on reset is canceled(2)
Vdet)
Min.
Standard
Typ.
Max.
Unit
–20°C ≤ Topr < 85°C
Vdet
V
–20°C ≤ Topr < 85°C, tW(por2) ≥ 0s(4)
100
ms
NOTES:
1. The voltage detection circuit which is embedded in a microcomputer is a factor to generate the hardware reset 2. Refer to 5.1.2 Hardware
Reset 2 of Hardware Manual for details.
2. This condition is not applicable when using VCC ≥ 1.0V.
3. When turning power on after the external power has been held below the valid voltage (Vpor1) for greater than 10 seconds, refer to Table 5.8
Reset Circuit Electrical Characteristics (When Not Using Hardware Reset 2).
4. tw(por2) is time to hold the external power below effective voltage (Vpor2).
Table 5.8 Reset Circuit Electrical Characteristics (When Not Using Hardware Reset 2)
Symbol
Vpor1
Measuring condition
Parameter
Min.
Standard
Typ.
Max.
–20°C ≤ Topr < 85°C
Power-on reset valid voltage
tW(Vpor1- Supply voltage rising time when power-on reset is canceled
Vdet)
0°C ≤ Topr ≤ 85°C, tW(por1) ≥
tW(Vpor1Vdet) Supply voltage rising time when power-on reset is canceled
–20°C ≤ Topr < 0°C, tW(por1) ≥
30s(2)
tW(Vpor1Vdet) Supply voltage rising time when power-on reset is canceled
tW(Vpor1- Supply voltage rising time when power-on reset is canceled
Vdet)
–20°C ≤ Topr < 0°C, tW(por1) ≥
10s(2)
10s(2)
0°C ≤ Topr ≤ 85°C, tW(por1) ≥ 1s(2)
NOTES:
1. When not using hardware reset 2, use with Vcc ≥ 2.7V.
2. tw(por1) is time to hold the external power below effective voltage (Vpor1).
Vdet(3)
Vdet(3)
Vcc min
Vpor2
Vpor1
Sampling time(1,2)
tw(por2) tw(Vpor2 –Vdet)
tw(por1) tw(Vpor1–Vdet)
Internal reset signal
(“L” effective)
1
X 32
fRING-S
1
X 32
fRING-S
NOTES:
1. Hold the voltage of the microcomputer operation voltage range (Vccmin or above) within sampling time.
2. A sampling clock is selectable. Refer to “5.4 Voltage Detection Circuit” of Hardware manual for details.
3. Vdet shows the voltage detection level of the voltage detection circuit. Refer to “5.4 Voltage Detection Circuit” of
Hardware manual for details.
Figure 5.3 Reset Circuit Electrical Characteristics
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 18 of 27
Unit
0.1
V
100
ms
100
ms
1
ms
0.5
ms
R8C/13 Group
5. Electrical Characteristics
Table 5.9 High-speed On-Chip Oscillator Circuit Electrical Characteristics
Symbol
Measuring condition
Parameter
High-speed on-chip oscillator frequency 1 / {td(HRoffset)+td(HR)} when the
reset is released
td(HRoffset) Settable high-speed on-chip oscillator minimum period
td(HR)
Min.
VCC=5.0V, Topr=25 °C
Set "4016" in the HR1 register
VCC=5.0V, Topr=25 °C
Set "0016" in the HR1 register
Differences when setting "0116" and "0016"
in the HR register
High-speed on-chip oscillator period adjusted unit
Standard
Typ.
Max.
Unit
8
MHz
61
ns
1
ns
High-speed on-chip oscillator frequency temperature dependence(1)
Frequency fluctuation in temperature range
of -10 °C to 50 °C
±5
%
High-speed on-chip oscillator frequency temperature dependence(2)
Frequency fluctuation in temperature range
of -40 °C to 85 °C
±10
%
NOTES:
1. The measuring condition is Vcc=AVcc=5.0 V and Topr=25 °C.
Table 5.10 Power Circuit Timing Characteristics
Symbol
Measuring condition
Parameter
td(P-R)
Time for internal power supply stabilization during powering-on(2)
td(R-S)
STOP release time(3)
Min.
Standard
Typ.
1
Max.
Unit
2000
µs
150
µs
NOTES:
1. The measuring condition is Vcc=AVcc=2.7 to 5.5 V and Topr=25 °C.
2. This shows the wait time until the internal power supply generating circuit is stabilized during power-on.
3. This shows the time until BCLK starts from the interrupt acknowledgement to cancel stop mode.
Table 5.11 Electrical Characteristics (1)
Symbol
[Vcc=5V]
Measuring condition
Parameter
"H" output voltage
Except XOUT
IOH=-5mA
IOH=-200µA
XOUT
Drive capacity HIGH
Drive capacity LOW
Except P10 to P17, XOUT
VOH
"L" output voltage
VOL
P10 to P17
XOUT
Hysteresis
II H
"H" input current
VCC-2.0
VCC-0.3
VCC-2.0
VCC-2.0
IOL= 5 mA
2 .0
V
IOL= 200 µA
0.45
V
2 .0
Drive capacity HIGH
IOH=-1 mA
IOH=-500µA
I O L= 1 5 m A
Drive capacity LOW
IOL= 5 mA
2.0
V
V
Drive capacity LOW
IOL= 200 µA
0.45
V
Drive capacity HIGH
IOL= 1 mA
IOL=500 µA
2 .0
V
2 .0
V
V
0 .2
INT0, INT1, INT2, INT3, KI0, KI1,
KI2, KI3, CNTRo, CNTR1, TCIN,
RxD0, RxD1, P45
1.0
0.2
II L
"L" input current
VI=5V
VI=0V
RPULLUP
Pull-up resistance
VI=0V
RfXIN
Feedback resistance
fRING-S
Low-speed on-chip oscillator frequency
VRAM
RAM retention voltage
At stop mode
NOTES:
1. Referenced to VCC = AVCC = 4.2 to 5.5V at Topr = -20 to 85 °C / -40 to 85 °C, f(XIN)=20MHz unless otherwise specified.
2.2
V
5.0
µA
µA
-5.0
30
50
40
1.0
125
XIN
page 19 of 27
Unit
V
V
V
V
RESET
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
Standard
Max.
Typ.
VCC
VC C
VCC
VC C
Drive capacity LOW
VT+-VT-
Min.
2 .0
167
kΩ
MΩ
250
kHz
V
R8C/13 Group
5. Electrical Characteristics
Table 5.12 Electrical Characteristics (2)
Symbol
[Vcc=5V]
Measuring condition
Parameter
High-speed
mode
Medium-speed
mode
ICC
Power supply current
(VCC=3.3 to 5.5V)
In single-chip mode, the output
pins are open and other pins
are VSS
XIN=20 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on=125 kHz
No division
XIN=16 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on=125 kHz
No division
XIN=10 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on=125 kHz
No division
XIN=20 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on=125 kHz
Division by 8
XIN=16 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on=125 kHz
Division by 8
XIN=10 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on=125 kHz
Division by 8
Main clock off
High-speed
High-speed on-chip oscillator on=8 MHz
on-chip oscillator Low-speed on-chip oscillator on=125 kHz
mode
No division
Max.
Unit
9
15
mA
8
14
mA
5
mA
4
mA
3
mA
2
mA
4
8
mA
1.5
Main clock off
Low-speed
High-speed on-chip oscillator off
on-chip oscillator Low-speed on-chip oscillator on=125 kHz
mode
Division by 8
470
900
µA
40
80
µA
38
76
µA
0.8
3.0
µA
Wait mode
Stop mode
Main clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator on=125 kHz
When a WAIT instruction is executed(1)
Peripheral clock operation
VC27="0"
Main clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator on=125 kHz
When a WAIT instruction is executed(1)
Peripheral clock off
VC27="0"
Main clock off, Topr=-25 °C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10="1"
Peripheral clock off
VC27="0"
NOTES:
1. Timer Y is operated with timer mode.
2. Referenced to VCC = AVCC = 4.2 to 5.5V at Topr = -20 to 85 °C / -40 to 85 °C, f(XIN)=20MHz unless otherwise specified.
page 20 of 27
Standard
Typ.
Main clock off
High-speed on-chip oscillator on=8 MHz
Low-speed on-chip oscillator on=125 kHz
Division by 8
Wait mode
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
Min.
mA
R8C/13 Group
5. Electrical Characteristics
Timing requirements [VCC=5V] (Unless otherwise noted: VCC = 5V, VSS = 0V at Topr = 25 °C)
Table 5.13 XIN input
Symbol
tC(XIN)
tWH(XIN)
tWL(XIN)
Parameter
XIN input cycle time
XIN input HIGH pulse width
XIN input LOW pulse width
Standard
Min.
Max.
50
–
25
–
25
–
Unit
Standard
Min.
Max.
100
–
40
–
40
–
Unit
Standard
Max.
Min.
400(1)
–
200(2)
–
200(2)
–
Unit
Standard
Min.
Max.
200
–
100
–
100
–
80
–
0
–
35
–
90
–
Unit
Standard
Max.
Min.
250(1)
–
250(2)
–
Unit
ns
ns
ns
________
Table 5.14 CNTR0 input, CNTR1 input, INT2 input
Symbol
tC(CNTR0)
tWH(CNTR0)
tWL(CNTR0)
Parameter
CNTR0 input cycle time
CNTR0 input HIGH pulse width
CNTR0 input LOW pulse width
ns
ns
ns
________
Table 5.15 TCIN input, INT3 input
Symbol
Parameter
tC(TCIN)
ns
TCIN input cycle time
tWH(TCIN)
ns
TCIN input HIGH pulse width
tWL(TCIN)
ns
TCIN input LOW pulse width
NOTES:
1. When using the Timer C input capture mode, adjust the cycle time above ( 1/ Timer C count source
frequency x 3).
2. When using the Timer C input capture mode, adjust the pulse width above ( 1/ Timer C count source
frequency x 1.5).
Table 5.5 Serial Interface
Symbol
tC(CK)
tW(CKH)
tW(CKL)
td(C-Q)
th(C-Q)
tsu(D-C)
th(C-D)
Parameter
CLKi input cycle time
CLKi input HIGH pulse width
CLKi input LOW pulse width
TxDi output delay time
TxDi hold time
RxDi input setup time
RxDi input hold time
ns
ns
ns
ns
ns
ns
ns
________
Table 5.17 External interrupt INT0 input
Symbol
tW(INH)
tW(INL)
Parameter
________
INT0
input HIGH pulse width
________
INT0 input LOW pulse width
ns
ns
NOTES:
________
________
1. When selecting the digital filter by the INT0 input filter select bit, use the INT0 input HIGH pulse width
to the greater value,either ( 1/ digital filter
clock frequency x 3) or the minimum
value of standard.
________
________
2. When selecting the digital filter by the INT0 input filter select bit, use the INT0 input LOW pusle width
to the greater value,either ( 1/ digital filter clock frequency x 3) or the minimum value of standard.
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 21 of 27
R8C/13 Group
5. Electrical Characteristics
VCC = 5V
tc(CNTR0)
tWH(CNTR0)
CNTR0 input
tWL(CNTR0)
tc(TCIN)
tWH(TCIN)
TCIN input
tWL(TCIN)
tc(XIN)
tWH(XIN)
XIN input
tWL(XIN)
tc(CK)
tW(CKH)
CLKi
tW(CKL)
th(C-Q)
TxDi
td(C-Q)
tsu(D-C)
RxDi
tW(INL)
INTi
tW(INH)
Figure 5.4 Vcc=5V timing diagram
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 22 of 27
th(C-D)
R8C/13 Group
5. Electrical Characteristics
Table 5.18 Electrical Characteristics (3)
Symbol
[Vcc=3V]
Measuring condition
Parameter
"H" output voltage
VOH
"L" output voltage
VOL
Except XOUT
IOH=-1mA
XOUT
Drive capacity HIGH
Drive capacity LOW
Except P10 to P17, XOUT
IOL= 1 mA
P10 to P17
Drive capacity HIGH
Drive capacity LOW
XOUT
Drive capacity HIGH
Drive capacity LOW
VT+-VT-
Hysteresis
II H
"H" input current
Min.
VCC-0.5
V
0 .5
V
IOL= 2 mA
IOL= 1 mA
0 .5
V
0 .5
V
IOL= 0.1 mA
IOL=50 µ A
0 .5
0 .5
V
V
0.2
0 .8
V
0.2
1 .8
4.0
V
µA
-4.0
µA
IOH=-0.1 mA
IOH=-50 µA
VCC-0.5
VCC-0.5
RESET
II L
"L" input current
RPULLUP
RfXIN
Pull-up resistance
VI=0V
fRING-S
Low-speed on-chip oscillator frequency
VRAM
RAM retention voltage
Feedback resistance
66
160
40
3.0
125
XIN
At stop mode
NOTES:
1. Referenced to VCC = AVCC = 2.7 to 3.3V at Topr = -20 to 85 °C / -40 to 85 °C, f(XIN)=10MHz unless otherwise specified.
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 23 of 27
Unit
VCC
VCC
VCC
INTo, INT1, INT2, INT3, KI0, KI1,
KI2, KI3, CNTR0, CNTR1, TCIN,
RxD0, RxD1, P45
VI=3V
VI=0V
Standard
Max.
Typ.
2 .0
V
V
500
kΩ
250
MΩ
kHz
V
R8C/13 Group
5. Electrical Characteristics
Table 5.19 Electrical Characteristics (4)
Symbol
[Vcc=3V]
Measuring condition
Parameter
High-speed
mode
Medium-speed
mode
ICC
Power supply current
(VCC=2.7 to 3.3V)
In single-chip mode, the output
pins are open and other pins
are VSS
XIN=20 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on=125 kHz
No division
XIN=16 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on=125 kHz
No division
XIN=10 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on=125 kHz
No division
XIN=20 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on=125 kHz
Division by 8
XIN=16 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on=125 kHz
Division by 8
XIN=10 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on=125 kHz
Division by 8
Max.
8
13
mA
7
12
mA
Unit
5
mA
3
mA
2 .5
mA
1 .6
mA
3 .5
Main clock off
High-speed on-chip oscillator on=8 MHz
Low-speed on-chip oscillator on=125 kHz
Division by 8
1.5
Main clock off
Low-speed
High-speed on-chip oscillator off
on-chip oscillator Low-speed on-chip oscillator on=125 kHz
mode
Division by 8
420
800
µA
Main clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator on=125 kHz
When a WAIT instruction is executed(1)
Peripheral clock operation
VC27="0"
37
74
µA
Main clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator on=125 kHz
When a WAIT instruction is executed(1)
Peripheral clock off
VC27="0"
35
70
µA
Main clock off, Topr=-25 °C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10="1"
Peripheral clock off
VC27="0"
0.7
3.0
µA
Wait mode
Stop mode
NOTES:
1. Timer Y is operated with timer mode.
2. Referenced to VCC = AVCC = 2.7 to 3.3V at Topr = -20 to 85 °C / -40 to 85 °C, f(XIN)=10MHz unless otherwise specified.
page 24 of 27
Standard
Typ.
Main clock off
High-speed
High-speed on-chip oscillator on=8 MHz
on-chip oscillator Low-speed on-chip oscillator on=125 kHz
mode
No division
Wait mode
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
Min.
7 .5
mA
mA
R8C/13 Group
5. Electrical Characteristics
Timing requirements [VCC=3V] (Unless otherwise noted: VCC = 3V, VSS = 0V at Topr = 25 °C)
Table 5.20 XIN input
Symbol
tC(XIN)
tWH(XIN)
tWL(XIN)
Parameter
XIN input cycle time
XIN input HIGH pulse width
XIN input LOW pulse width
Standard
Min.
Max.
100
–
40
–
40
–
Unit
Standard
Min.
Max.
300
–
120
–
120
–
Unit
Standard
Min.
Max.
1200(1)
–
600(2)
–
600(2)
–
Unit
Standard
Min.
Max.
300
–
150
–
150
–
160
–
0
–
55
–
90
–
Unit
Standard
Min.
Max.
380(1)
–
380(2)
–
Unit
ns
ns
ns
________
Table 5.21 CNTR0 input, CNTR1 input, INT2 input
Symbol
tC(CNTR0)
tWH(CNTR0)
tWL(CNTR0)
Parameter
CNTR0 input cycle time
CNTR0 input HIGH pulse width
CNTR0 input LOW pulse width
ns
ns
ns
________
Table 5.22 TCIN input, INT3 input
Symbol
Parameter
tC(TCIN)
ns
TCIN input cycle time
tWH(TCIN)
ns
TCIN input HIGH pulse width
tWL(TCIN)
ns
TCIN input LOW pulse width
NOTES:
1. When using the Timer C input capture mode, adjust the cycle time above ( 1/ Timer C count source
frequency x 3).
2. When using the Timer C input capture mode, adjust the pulse width above ( 1/ Timer C count source
frequency x 1.5).
Table 5.23 Serial Interface
Symbol
tC(CK)
tW(CKH)
tW(CKL)
td(C-Q)
th(C-Q)
tsu(D-C)
th(C-D)
Parameter
CLKi input cycle time
CLKi input HIGH pulse width
CLKi input LOW pulse width
TxDi output delay time
TxDi hold time
RxDi input setup time
RxDi input hold time
ns
ns
ns
ns
ns
ns
ns
________
Table 5.24 External interrupt INT0 input
Symbol
Parameter
________
tW(INH)
ns
INT0
input HIGH pulse width
________
tW(INL)
ns
INT0 input LOW pulse width
NOTES:
________
________
1. When selecting the digital filter by the INT0 input filter select bit, use the INT0 input HIGH pulse width
to the greater value,either ( 1/ digital filter
clock frequency x 3) or the minimum
value of standard.
________
________
2 . When selecting the digital filter by the INT0 input filter select bit, use the INT0 input LOW pusle width
to the greater value,either ( 1/ digital filter clock frequency x 3) or the minimum value of standard.
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 25 of 27
R8C/13 Group
5. Electrical Characteristics
VCC = 3V
tc(CNTR0)
tWH(CNTR0)
CNTR0 input
tWL(CNTR0)
tc(TCIN)
tWH(TCIN)
TCIN input
tWL(TCIN)
tc(XIN)
tWH(XIN)
XIN input
tWL(XIN)
tc(CK)
tW(CKH)
CLKi
tW(CKL)
th(C-Q)
TxDi
td(C-Q)
tsu(D-C)
RxDi
tW(INL)
INTi
tW(INH)
Figure 5.5 Vcc=3V timing diagram
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 26 of 27
th(C-D)
R8C/13 Group
Package Dimensions
Package Dimensions
JEITA Package Code
P-LQFP32-7x7-0.80
RENESAS Code
PLQP0032GB-A
Previous Code
32P6U-A
MASS[Typ.]
0.2g
HD
*1
D
24
17
NOTE)
1. DIMENSIONS "*1" AND "*2"
DO NOT INCLUDE MOLD FLASH.
2. DIMENSION "*3" DOES NOT
INCLUDE TRIM OFFSET.
16
25
bp
c
c1
HE
*2
E
b1
Reference
Symbol
9
1
ZE
Terminal cross section
32
8
ZD
c
A
A1
F
A2
Index mark
L
D
E
A2
HD
HE
A
A1
bp
b1
c
c1
L1
y
e
Rev.1.20 Jan 27, 2006
REJ03B0069-0120
page 27 of 27
*3
Detail F
bp
x
e
x
y
ZD
ZE
L
L1
Dimension in Millimeters
Min Nom Max
6.9 7.0 7.1
6.9 7.0 7.1
1.4
8.8 9.0 9.2
8.8 9.0 9.2
1.7
0.1 0.2
0
0.32 0.37 0.42
0.35
0.09 0.145 0.20
0.125
0°
8°
0.8
0.20
0.10
0.7
0.7
0.3 0.5 0.7
1.0
REVISION HISTORY
Rev.
R8C/13 Group Datasheet
Date
Description
Summary
Page
First edition issued
0.10 Oct 28, 2003
0.20 Dec05, 2003
5
Figure 1.3 revised
10
Chapter 4, NOTES revised
16
Table 5.4 revised
Table 5.5 revised
17
Table 5.6 revised
Figure 5.3 added
18
Table 5.8 revised
Table 5.10 revised
21
Figure 5.3 revised to Figure 5.4
22
Table 5.17 revised
25
Figure 5.4 revised to Figure 5.5
1.00 Sep 30, 2004 All pages Words standardized (on-chip oscillator, serial interface, A/D)
2
Table 1.1 revised
Figure 1.3, NOTES 3 added
5
Table 1.3 revised
6
Figure 3.1, NOTES added
9
One body sentence in chapter 4 added ; Titles of Table 4.1 to 4.4 added
10-13
Table 4.3 revised ; Table 4.4 revised
12
Table 5.2 revised
14
Table 5.3 revised
15
Table 5.4 and Table 5.5 revised
16
Table 5.6, 5.7 and 5.8 revised ; Figure 5.3 revised
17
Table 5.9 and 5.11 revised
18
Table 5.12 revised
19
Table 5.13 revised
20
Table 5.18 revised
22
Table 5.19 revised
23
Table 5.20 and Table 5.24 revised
24
1.10 Apr.27.2005
4
5
10
12
15
16
Table 1.2, Figure 1.2 package name revised
Figure 1.3 package name revised
Table 4.1 revised
Table 4.3 revised
Table 5.3 partly revised
Table 5.4, Table 5.5 partly added
A-1
REVISION HISTORY
Rev.
R8C/13 Group Datasheet
Date
Description
Summary
Page
1.10 Apr.27.2005
17
18
22
26
Table 5.7, 5.8 revised
Table 5.10, Table 5.11 partly revised
Table 5.18 partly revised
Package Dimensions revised
1.20 Jan.27.2006
2
3
4
Table 1.1 Performance outline revised
Figure 1.1 Block diagram partly revised
1.4 Product Information, title of Table 1.2
“Product List” → “Product Informaton” revised
ROM capacity; “Program area” → “Program ROM”,
“Data area” → “Data flash” revised
Figure 1.2 Type No., Memory Size, and Package partly revised
Table 1.3 Pin description revised
2 Central Processing Unit (CPU) revised
Figure 2.1 CPU register revised
3 Memory, Figure 3.1 Memory Map;
“Program area” → “Program ROM”, “Data area” → “Data flash” revised
Table 4.1 SFR Information(1) NOTES:1 revised
Table 4.2 SFR Information(2) NOTES:1 revised
Table 4.3 SFR Information(3);
008116: “Prescaler Y” → “Prescaler Y Register”
008216: “Timer Y Secondary” → “Timer Y Secondary Register”
008316: “Timer Y Primary” → “Timer Y Primary Register”
008516: “Prescaler Z” → “Prescaler Z Register”
008616: “Timer Z Secondary” → “Timer Z Secondary Register”
008716: “Timer Z Primary” → “Timer Z Primary Register”
008C16: “Prescaler X” → “Prescaler X Register” revised
NOTES:1, 2 revised
Table 4.4 SFR Information(4) NOTES:1 revised
Table 5.2 Recommended Operating Conditions; NOTES: 1, 2, 3 revised
Table 5.3 A/D Conversion Characteristics;
“A/D operation clock frequency” → “A/D operating clock frequency” revised
NOTES: 1, 2, 3, 4 revised
Table 5.4 Flash Memory (Program ROM) Electrical Characteristics;
“Data retention duration” → “Data hold time” revised
“Topr” → “Ambient temperature”
NOTES: 1 to 7 added
Measuring condition of byte program time and block erase time deleted
Table 5.5 Flash Memory (Data flash Block A, Block B) Electrical characteristics
“Data retention duration” → “Data hold time” revised
“Topr” → “Ambient temperature”
NOTES: 1, 3 revised, NOTES: 9 added
Measuring condition of byte program time and block erase time deleted
Table 5.7 Reset Circuit Electrical Characteristics (When Using Hardware Reset 2)
NOTES: 3 revised
Table 5.9 High-speed On-Chip Oscillator Circuit Electrical Characteristics;
“High-speed on-chip oscillator temperature dependence” →
“High-speed on-chip oscillator frequency temperature dependence” revised
Table 5.11 Electrical Characteristics (1) [VCC=5V];
“P10 to P17 Except XOUT” → “Except P10 to P17, XOUT” revised
6
7-8
9
10
11
12
13
14
15
16
17
18
19
A-2
REVISION HISTORY
Rev.
R8C/13 Group Datasheet
Date
Description
Summary
Page
1.20 Jan.27.2006
20
23
24
Table 5.12 Electrical Characteristics (2) [VCC=5V];
NOTES: 1, 2 revised
Measuring condition Stop mode: “Topr=-25 °C” added
Table 5.18 Electrical Characteristics (3) [VCC=3V]
“P10 to P17 Except XOUT” → “Except P10 to P17, XOUT” revised
Table 5.19 Electrical Characteristics (4) [VCC=3V]
NOTES: 1, 2 revised
Measuring condition Stop mode: “Topr=-25 °C” added
A-3
Sales Strategic Planning Div.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Keep safety first in your circuit designs!
1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble
may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary
circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's
application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party.
2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data,
diagrams, charts, programs, algorithms, or circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of
publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is
therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product
information before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor
home page (http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to
evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes
no responsibility for any damage, liability or other loss resulting from the information contained herein.
5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life
is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a
product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater
use.
6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and
cannot be imported into a country other than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein.
http://www.renesas.com
RENESAS SALES OFFICES
Refer to "http://www.renesas.com/en/network" for the latest and detailed information.
Renesas Technology America, Inc.
450 Holger Way, San Jose, CA 95134-1368, U.S.A
Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501
Renesas Technology Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900
Renesas Technology (Shanghai) Co., Ltd.
Unit 205, AZIA Center, No.133 Yincheng Rd (n), Pudong District, Shanghai 200120, China
Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7898
Renesas Technology Hong Kong Ltd.
7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong
Tel: <852> 2265-6688, Fax: <852> 2730-6071
Renesas Technology Taiwan Co., Ltd.
10th Floor, No.99, Fushing North Road, Taipei, Taiwan
Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999
Renesas Technology Singapore Pte. Ltd.
1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632
Tel: <65> 6213-0200, Fax: <65> 6278-8001
Renesas Technology Korea Co., Ltd.
Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea
Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145
Renesas Technology Malaysia Sdn. Bhd
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: <603> 7955-9390, Fax: <603> 7955-9510
© 2006. Renesas Technology Corp., All rights reserved. Printed in Japan.
Colophon .5.0