TS19310A/B Single-Stage PFC TRIAC Dimmable LED Driver SOT-26 Pin Definition: 1. COM 2. GND 3. CS 4. OUT 5. VCC 6. DMG Description TS19310 is a buck/boost control IC with phase angle decoding circuit and hold current adjusting function for TRIAC dimming LED lighting. TS19310 achieves high power factor and low total harmonic distortion (THD) operation by boundary conduction mode (BCM). The line and load regulation of LED current is about ±3%, based on particular control method. Features Applications ● ● ● ● ● LED Lighting Down Light Tube Lamp PAR Lamp Bulb ● ● ● ● ● ● ● ● Built-in Phase Angle Decoding TRIAC Hold Current Management Technique PSR and Buck/Boost Control Universal Input Voltage Range TS19310ACX6: 90 VAC ~ 135 VAC TS19310BCX6: 180 VAC ~ 264 VAC Active Power Factor Correction Technique Constant Output Current Control LED Driver Open-LED Protection on DMG Pin Over-Voltage Protection on VCC Pin Short-LED Protection Cycle by Cycle Over-Current Protection on CS Pin Over-Temperature Protection Gate Driving Voltage Clamping Ordering Information Part No. Package Packing TS19310ACX6 RFG SOT-26 3kpcs/7” Reel TS19310BCX6 RFG SOT-26 3kpcs/7” Reel Note: “G” denotes for Halogen- and Antimony-free as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and <1000ppm antimony compounds Absolute Maximum Ratings (Note 1) Parameter Symbol Range Unit Power Supply Pin VCC 40 V DMG Voltage to GND VDMG -0.3 to 40 V OUT Voltage to GND VOUT -0.3 to 40 V CS Voltage to GND VCS -0.3 to 5.5 V VCOM -0.3 to 5.5 V Junction Temperature Range TJ -40 to +150 °C Storage Temperature Range TSTG -65 to +150 °C Lead Temperature (soldering 10 s) TLEAD 260 °C PD 0.3 W HBM 2 kV COM Voltage to GND Power Dissipation @ TA=25°C ESD Rating (Human Body Mode) (Note 2) 1/8 Version: A14 TS19310A/B Single-Stage PFC TRIAC Dimmable LED Driver Thermal Information Parameter Symbol Range Unit RθJA 220 °C/W RθJC 106.6 °C/W Symbol Conditions Unit Power Supply Pin VCC 34.5 V DMG Voltage to GND VDMG -0.3 to 11.2 V OUT Voltage to GND VOUT -0.3 to 19 V CS Voltage to GND VCS -0.3 to 5 V VCOM -0.3 to 5 V Operating Junction Temperature Range TJ -40 to +125 °C Operating Ambient Temperature Range TOPA -40 to +85 °C Thermal Resistance Junction to Ambient (Note 3) Thermal Resistance Junction to Case Recommended Operating Conditions (Note 4) Parameter COM Voltage to GND Electrical Characteristics (TA= 25°C, unless otherwise specified.) Parameter Symbol Condition Min Typ Max Unit Turn-on Voltage VCC_ON 17 18 19 V Turn-off Voltage VCC_OFF 8.5 9.5 10 V Quiescent Current 1 IQ1 VCC=17V, at VCC off -- 30 50 μA Quiescent Current 2 IQ2 Start up at 4.5 kHz -- 600 800 μA Operation Supply Current ICC -- 2.5 3.0 mA VCC Voltage Protection VOVPA 31 32 34 V Output Voltage Protection VOVPS 10 10.5 11 V CS Limit Voltage VOCP 1.15 1.25 1.35 V VO_STR -- 3 -- V tSTR -- 222 -- μs gm -- 60 -- μS ICOMP_SOU -- 20 -- μA Protection Short Circuit Protection (Note 5) Oscillator Start-up Timer GM Amplifier Transconductance Source Current 2/8 Version: A14 TS19310A/B Single-Stage PFC TRIAC Dimmable LED Driver Electrical Characteristics (TA= 25°C, unless otherwise specified.) Parameter Symbol Condition Min Typ Max Unit Driver VOH VCC=33V, IO = 10mA -- 1.2 1.5 V VOL VCC=33V, IO = -10mA -- 0.12 -- V Rise Time tRISE VCC=20V, CO =1nF -- 40 -- ns Fall Time tFALL VCC=20V, CO =1nF -- 80 -- ns VO_CLAMP -- -- 19 V tLEB -- 500 -- ns OTP Trip Point -- 150 -- °C OTP Release Point -- 115 -- °C OTP Threshold Hysteresis -- 35 -- °C Dropout Voltage Output Clamp Voltage Leading Edge Blanking Time Over Temperature Protection (Note 6) Notes: 1. Stresses listed as the above “Absolute Maximum Ratings” may cause permanent damage to the device. These are for stress ratings. Functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may remain possibility to affect device reliability. 2. Devices are ESD sensitive. Handling precaution recommended. 3. Thermal Resistance is specified with the component mounted on a low effective thermal conductivity test board in free air at TA=25°C. 4. The device is not guaranteed to function outside its operating conditions. 5. Guaranteed by design. 6. Auto recovery type. 3/8 Version: A14 TS19310A/B Single-Stage PFC TRIAC Dimmable LED Driver Function Block CLR COM RST CT R SR Latch Q CLK Driver OUT S VCC BG VREF PRO SCP, OCP OVPA (VCC) OVPS (OUT) X OSC One shot CLK SET_str SET_act TDIS DMG DMG Multiply GM Phase Angle Decode VREF GND CSP S/H CS Block Diagram Pin Description Pin No. Name 1 2 3 4 5 6 COM GND CS OUT VCC DMG Function Output pin of error amplifier. Ground return for all internal circuitry. Input current sense pin. Power MOSFET output pin. Power supply pin for all internal circuitry. Zero current demagnetization sensing. 4/8 Version: A14 TS19310A/B Single-Stage PFC TRIAC Dimmable LED Driver Typical Application Circuit Application Information Function Description The TS19310 is boundary conduction mode (BCM) operation with constant on time based regulator design to achieve high power factor performance. The TS19310 has built-in functions of phase dimmable, and included protection function related VCC over-voltage protection, open-LED protection, short-LED protection, overtemperature protection, primary side current limit, and gate clamp is within. The TS19310 is the sense switch current from CS voltage multiplier by test data input signal (TDIS) to get the output current information by system close loop feedback. The average output current can express by below formula. IOUT NP 0.333* NS 2 RS Where: ● IOUT is the average output current ● NP is the primary-side turn ratio ● NS is the secondary-side turn ratio ● 0.333 is the reference potential setting of IC ● 2 is the reference potential setting of IC ● η is the efficiency ● RS is the sensing resistor connected between the MOSFET source and the GND Pin Detail Pin 1: Compensation This is the output of the gm amplifier. Connect with a suitable RC network to ground. Pin 2: Ground GND is the reference node of internal circuit. 5/8 Version: A14 TS19310A/B Single-Stage PFC TRIAC Dimmable LED Driver Pin 3: Current Sense MOSFET current signal sensing for multiply, phase angle decode and current limit setting function. 1.25 ICS(Limit) RS Where: ICS is the input current sense IC internal CS Pin 1.25V Over voltage level RS is the sensing resistor connected between the MOSFET source and GND Pin 4: Output Gate drive for external MOSFET switch and has built-in gate clamp function. Pin 5: VCC Power supply for the controller during normal operation. The controller will start up when VCC reaches 18V (typical) and will shut-down when VCC voltage is below 9.5V (typical). A decoupling capacitor should be connected between the VCC and GND pin as close as possible. The TS19310 performs VCC over voltage protection though VCC pin. Once VCC pin exceeds 32V, TS19310 turns off and latches the MOSFET until VCC goes below VCC_OFF. Pin 6: DMG The Output voltage is reflected by the auxiliary winding (NA) voltage of Flyback transformer, the DMG pin can sense output information to depart from start up voltage (VO_STR) and protection voltage (VO_OVP). When DMG sense voltage under VO_STR, the circuit will work on short circuit protection, f STR=1/tSTR. When DMG sense voltage over VO_OVP, the circuit will work on over voltage protection, it will latch out off until VCC goes below VCC_OFF. VCC NA VDMG_OVP RDMG1 DMG RDMG2 OVP Protection (by DMG) NS RDGM1 RDGM2 × VOVPS × NA RDMG2 OVP Protection (by VCC) CDMG VVCC _ OVP NS × VOVPA NA Short Circuit Protection VO _ Short NS RDMG1 RDMG2 × VO _ STR × NA RDMG2 Where: ● VDMG_OVP is the output-over-voltage protection point ● VOVPS is the over voltage protection signal ● VO_STR is the start-up timer ● NA is the number of auxiliary-winding turns ● NS is the number of secondary-winding turns 6/8 Version: A14 TS19310A/B Single-Stage PFC TRIAC Dimmable LED Driver SOT-26 Mechanical Drawing Unit: Millimeters Marking Diagram SM SN L Y W = TS19310CXA Device Code = TS19310CXB Device Code = Lot Code A~Z = Year Code (D=2014, E=2015, F=2016, G=2017, H=2018, J=2019, K=2020) = Week Code A~Z = wk1~wk26 A~Z = wk27~wk52 7/8 Version: A14 TS19310A/B Single-Stage PFC TRIAC Dimmable LED Driver Notice Specifications of the products displayed herein are subject to change without notice. TSC or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, to any intellectual property rights is granted by this document. Except as provided in TSC’s terms and conditions of sale for such products, TSC assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of TSC products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify TSC for any damages resulting from such improper use or sale. 8/8 Version: A14