® RT8080 1.5MHz, 1A, High Efficiency PWM Step-Down DC/DC Converter General Description Features The RT8080 is a high efficiency Pulse-Width-Modulated (PWM) step-down DC/DC converter. Capable of delivering 1A output current over a wide input voltage range from 2.8V to 5.5V, the RT8080 is ideally suited for portable electronic devices that are powered from 1-cell Li-ion battery or from other power sources such as cellular phones, PDAs and hand-held devices. z z z z z z z z Two operating modes are available including : PWM/LowDropout auto switch and shutdown modes. The Internal synchronous rectifier with low RDS(ON) dramatically reduces 2.8V to 5.5V Input Range Adjustable Output From 0.6V to VIN 1A Output Current 95% Efficiency No Schottky Diode Required 1.5MHz Fixed-Frequency PWM Operation Small 6-Lead WDFN Package RoHS Compliant and Halogen Free Applications z conduction loss at PWM mode. No external Schottky diode is required in practical application. z z The RT8080 enters Low Dropout mode when normal PWM cannot provide regulated output voltage by continuously turning on the upper P-MOSFET. When EN pin is pulled low, the RT8080 will enter shutdown mode and consume less than 0.1μA. z z Mobile Phones Personal Information Appliances Wireless and DSL Modems MP3 Players Portable Instruments Marking Information 0V : Product Code The switching ripple is easily smoothed-out by small package filtering elements due to a fixed operating frequency of 1.5MHz. This along with small WDFN-6L 2x2 package provides small PCB area application. Other features include soft start, lower internal reference voltage with 2% accuracy, over temperature protection, and over current protection. W : Date Code 0VW Simplified Application Circuit L VIN VIN CIN LX RT8080 EN DS8080-00 July 2012 R1 FB GND Copyright © 2012 Richtek Technology Corporation. All rights reserved. VOUT C1 COUT IR2 R2 is a registered trademark of Richtek Technology Corporation. www.richtek.com 1 RT8080 Ordering Information Pin Configurations RT8080 (TOP VIEW) Lead Plating System G : Green (Halogen Free and Pb Free) NC 1 EN VIN 2 GND Package Type QW : WDFN-6L 2x2 (W-Type) 3 7 6 FB 5 GND LX 4 Note : WDFN-6L 2x2 Richtek products are : ` RoHS compliant and compatible with the current requirements of IPC/JEDEC J-STD-020. ` Suitable for use in SnPb or Pb-free soldering processes. Functional Pin Description Pin No. Pin Name Pin Function 1 NC No Internal Connection. 2 EN Chip Enable (Active High). 3 VIN Power Input. 4 LX Switch Node. GND Ground. The exposed pad must be soldered to a large PCB and connected to GND for maximum power dissipation. FB Feedback Voltage Input. 5, 7 (Exposed Pad) 6 Function Block Diagram VIN RS1 Current Limit Detector OSC Slope Compensation Current Sense Soft-Start FB Control Logic PWM COMP Comparator Error Amplifier Shutdown Control RC CC UVLO & Power Good Detector Driver LX Over Temperature Protection RS2 VREF Enable Threshold GND Enable Comparator EN Copyright © 2012 Richtek Technology Corporation. All rights reserved. www.richtek.com 2 is a registered trademark of Richtek Technology Corporation. DS8080-00 July 2012 RT8080 Operation The RT8080 is a synchronous step-down DC/DC converter with two integrated power MOSFETs and operates at 1.5MHz fixed frequency. It can deliver up to 1A output current from a 2.8V to 5.5V input supply. The RT8080's current mode architecture allows the transient response to be optimized over a wide input voltage and load range. Cycle-by-cycle current limit provides protection against shorted output and soft-start eliminates input current surge during start-up. The RT8080 is available in WDFN-6L 2x2 (Exposed Pad) packages. The peak current of high side MOSFET is measured by internal sensing resistor. The Current Signal combines current sense with slope compensation and compares with COMP voltage by the PWM comparator. The error amplifier adjusts COMP voltage by comparing the feedback signal (VFB) from the output voltage with the internal 0.6V reference. When the load current increases, it causes a drop in the feedback voltage relative to the reference, and the COMP voltage will rise to allow higher inductor current to match the load current. Copyright © 2012 Richtek Technology Corporation. All rights reserved. DS8080-00 July 2012 OSC The internal oscillator typically runs at 1.5 MHz switching frequency. Over Temperature Protection (OTP) The RT8080 implement an internal over temperature protection. When junction temperature is higher than 150°C, it will stop switching. Once the junction temperature decreases below 130°C, the RT8080 will automatically resume switching. Enable Comparator When EN pin input voltage is higher/lower than EN threshold voltage, the converter is enabled/disabled. The EN pin can be connected to VIN directly for automatic startup. Soft-Start (SS) An internal current source charges an internal capacitor to build the soft-start ramp-voltage (VSS). The VF voltage will track the internal ramp voltage during the soft-start interval. is a registered trademark of Richtek Technology Corporation. www.richtek.com 3 RT8080 Absolute Maximum Ratings z z z z z z z z z (Note 1) Recommended Operating Conditions z z z −0.3V to 6.5V −0.3V to VIN −0.3V to (VIN + 0.3V) −4.5V to 7.5V Supply Input Voltage, VIN ---------------------------------------------------------------------------------------EN, FB to GND -----------------------------------------------------------------------------------------------------LX to GND -----------------------------------------------------------------------------------------------------------<20ns ----------------------------------------------------------------------------------------------------------------Power Dissipation, PD @ TA = 25°C WDFN-6L 2x2 ------------------------------------------------------------------------------------------------------Package Thermal Resistance (Note 2) WDFN-6L 2x2, θJA -------------------------------------------------------------------------------------------------WDFN-6L 2x2, θJC ------------------------------------------------------------------------------------------------Lead Temperature (Soldering, 10 sec.) -----------------------------------------------------------------------Storage Temperature Range ------------------------------------------------------------------------------------Junction Temperature ---------------------------------------------------------------------------------------------ESD Susceptibility (Note 3) HBM (Human Body Model) --------------------------------------------------------------------------------------- 0.833W 120°C/W 8.2°C/W 260°C −65°C to 150°C 150°C 2kV (Note 4) Supply Input Voltage, VIN ---------------------------------------------------------------------------------------- 2.8V to 5.5V Junction Temperature Range ------------------------------------------------------------------------------------- −40°C to 125°C Ambient Temperature Range ------------------------------------------------------------------------------------- −40°C to 85°C Electrical Characteristics (VIN = 3.6V, TA = 25°C, unless otherwise specified) Parameter Symbol Test Conditions Min Typ Max Unit Quiescent Current IQ IOUT = 0mA, VFB = VREF + 5% -- 78 -- μA Shutdown Current ISHDN EN = GND -- 0.1 1 μA Reference Voltage VREF 0.588 0.6 0.612 V Adjustable Output Range VOUT (Note 5) VREF -- VIN − 0.2V V FB Input Current IFB VFB = VIN −50 -- 50 nA P-MOSFET On Resistance RDS(ON)_P IOUT = 200mA -- 0.25 -- Ω N-MOSFET On Resistance RDS(ON)_N IOUT = 200mA -- 0.25 -- Ω P-Channel Current Limit ILIM_P VIN = 2.8V to 5.5V 1.3 1.5 -- A High-Level VEN_H VIN = 2.8V to 5.5V 1.5 -- -- Low-Level VEN_L VIN = 2.8V to 5.5V -- -- 0.4 -- 2.3 -- V -- 0.2 -- V 1.2 1.5 1.8 MHz -- 150 -- °C 100 -- -- % EN Input Voltage Under Voltage Lockout Threshold UVLO Hysteresis UVLO Oscillator Frequency fOSC Thermal Shutdown Temperature TSD VIN = 3.6V, IOUT = 100mA Maximum Duty Cycle Copyright © 2012 Richtek Technology Corporation. All rights reserved. www.richtek.com 4 V is a registered trademark of Richtek Technology Corporation. DS8080-00 July 2012 RT8080 Note 1. Stresses beyond those listed “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions may affect device reliability. Note 2. θJA is measured at TA = 25°C on a high effective thermal conductivity four-layer test board per JEDEC 51-7. θJC is measured at the exposed pad of the package. Note 3. Devices are ESD sensitive. Handling precaution recommended. Note 4. The device is not guaranteed to function outside its operating conditions. Note 5. Guarantee by design. Copyright © 2012 Richtek Technology Corporation. All rights reserved. DS8080-00 July 2012 is a registered trademark of Richtek Technology Corporation. www.richtek.com 5 RT8080 Typical Application Circuit VIN 2.8V to 5.5V 3 VIN CIN 4.7µF LX 4 EN FB VOUT C1 RT8080 2 L 2.2µH R1 6 COUT 10µF IR2 GND 5, 7 (Exposed Pad) R2 Table 1. Recommended Component Selection VOUT (V) C IN (μF) COUT (μF) C1 (pF) L (μH) R1 (kΩ) R2 (kΩ) 1.2 4.7 10 10 2.2 62 62 3.3 4.7 10 10 2.2 280 62 Copyright © 2012 Richtek Technology Corporation. All rights reserved. www.richtek.com 6 is a registered trademark of Richtek Technology Corporation. DS8080-00 July 2012 RT8080 Typical Operating Characteristics Efficiency vs. Output Current Efficiency vs. Output Current 100 100 90 90 VIN = 3.6V VIN = 4.5V VIN = 5.5V 70 VIN = 2.8V VIN = 3.6V VIN = 5.5V 80 Efficiency (%) Efficiency (%) 80 60 50 40 30 20 70 60 50 40 30 20 10 10 VOUT = 3.3V 0 VOUT = 1.2V 0 0 0.2 0.4 0.6 0.8 1 0 0.2 Output Current (A) UVLO Voltage vs. Temperature 0.6 0.8 1 EN Pin Threshold vs. Input Voltage 2.5 1.5 2.4 1.4 2.3 Rising EN Pin Threshold (V) Input Voltage (V) 0.4 Output Current (A) 2.2 2.1 2.0 1.9 Falling 1.8 1.7 VOUT = 1.2V, IOUT = 0A -25 0 25 50 75 100 1.2 Rising 1.1 1.0 Falling 0.9 0.8 0.7 0.6 1.6 -50 1.3 VOUT = 1.2V, IOUT = 0A 0.5 125 2.5 3 Temperature (°C) 3.5 4 4.5 5 5.5 Input Voltage (V) EN Pin Threshold vs. Temperature Output Voltage vs. Input Voltage 1.5 1.23 1.3 1.22 1.2 Output Voltage (V) EN Pin Threshold (V) 1.4 Rising 1.1 1.0 0.9 Falling 0.8 0.7 0.6 1.21 1.20 IOUT = 0.5A 1.19 IOUT = 1A VIN = 3.6V, VOUT = 1.2V, IOUT = 0A 0.5 1.18 -50 -25 0 25 50 75 100 Temperature (°C) Copyright © 2012 Richtek Technology Corporation. All rights reserved. DS8080-00 July 2012 125 2.5 3 3.5 4 4.5 5 5.5 Input Voltage (V) is a registered trademark of Richtek Technology Corporation. www.richtek.com 7 RT8080 Output Voltage vs. Temperature 1.23 1.22 1.22 Output Voltage (V) Output Voltage (V) Output Voltage vs. Output Current 1.23 1.21 VIN = 5.5V 1.20 VIN = 3.6V 1.21 1.20 1.19 1.19 1.18 1.18 VIN = 3.6V, IOUT = 0A 0 0.2 0.4 0.6 0.8 1 -50 -25 0 Output Current (A) 75 100 125 Frequency vs. Temperature 1.8 1.7 1.7 Frequency (MHz)1 1.8 1.6 1.5 1.4 1.3 1.6 1.5 1.4 1.3 VIN = 3.6V, VOUT = 1.2V VIN = 3.6V, VOUT = 1.2V 1.2 1.2 2.5 3 3.5 4 4.5 5 5.5 -50 -25 0 Input Voltage (V) 25 50 75 100 125 Temperature (°C) Current Limit vs. Input Voltage Output Current Limit vs. Temperature 2.2 2.0 1.8 2.0 VIN = 5.5V Current Limit (A) Current Limit (A) 50 Temperature (°C) Frequency vs. Input Voltage Frequency (MHz)1 25 1.8 1.6 1.4 1.6 VIN = 2.8V 1.4 1.2 VIN = 3.6V 1.0 VOUT = 1.2V 1.2 VOUT = 1.2V 0.8 2.5 3 3.5 4 4.5 5 Input Voltage (V) Copyright © 2012 Richtek Technology Corporation. All rights reserved. www.richtek.com 8 5.5 -50 -25 0 25 50 75 100 125 Temperature (°C) is a registered trademark of Richtek Technology Corporation. DS8080-00 July 2012 RT8080 Power On from EN Power On from EN VIN = 3.6V, VOUT = 1.2V, IOUT = 10mA VIN = 3.6V, VOUT = 1.2V, IOUT = 1A VEN (2V/Div) VEN (2V/Div) VOUT (1V/Div) VOUT (1V/Div) I IN (500mA/Div) I IN (500mA/Div) Time (500μs/Div) Time (500μs/Div) Power On from VIN Power Off from EN VIN = 3.6V, VOUT = 1.2V, ILX = 1A VEN = 3V, VOUT = 1.2V, ILX = 1A VIN (2V/Div) VEN (2V/Div) VOUT (1V/Div) VOUT (1V/Div) ILX (1A/Div) ILX (1A/Div) Time (1ms/Div) Time (100μs/Div) Load Transient Response Load Transient Response VIN = 3.6V, VOUT = 1.2V, IOUT = 50mA to 1A VIN = 3.6V, VOUT = 1.2V, IOUT = 50mA to 0.5A VOUT (50mV/Div) VOUT (50mV/Div) IOUT (500mA/Div) IOUT (500mA/Div) Time (50μs/Div) Copyright © 2012 Richtek Technology Corporation. All rights reserved. DS8080-00 July 2012 Time (50μs/Div) is a registered trademark of Richtek Technology Corporation. www.richtek.com 9 RT8080 Load Transient Response Load Transient Response VIN = 5V, VOUT = 1.2V, IOUT = 50mA to 0.5A VIN = 5V, VOUT = 1.2V, IOUT = 50mA to 1A VOUT (50mV/Div) VOUT (50mV/Div) IOUT (500mA/Div) IOUT (500mA/Div) Time (50μs/Div) Time (50μs/Div) Output Ripple Voltage Output Ripple Voltage VIN = 3.6V, VOUT = 1.2V, IOUT = 1A VIN = 5V, VOUT = 1.2V, IOUT = 1A VOUT (10mV/Div) VOUT (10mV/Div) VLX (2V/Div) VLX (2V/Div) Time (500ns/Div) Copyright © 2012 Richtek Technology Corporation. All rights reserved. www.richtek.com 10 Time (500ns/Div) is a registered trademark of Richtek Technology Corporation. DS8080-00 July 2012 RT8080 Applications Information The basic RT8080 application circuit is shown in Typical Application Circuit. External component selection is determined by the maximum load current and begins with the selection of the inductor value and operating frequency followed by CIN and COUT. current is exceeded. This results in an abrupt increase in inductor ripple current and consequent output voltage ripple. Do not allow the core to saturate! Inductor Selection Toroid or shielded pot cores in ferrite or permalloy materials are small and don't radiate energy but generally cost more than powdered iron core inductors with similar characteristics. The choice of which style inductor to use mainly depends on the price vs size requirements and any radiated field/EMI requirements. For a given input and output voltage, the inductor value and operating frequency determine the ripple current. The ripple current ΔIL increases with higher VIN and decreases with higher inductance. V V ΔIL = ⎡⎢ OUT ⎤⎥ × ⎡⎢1− OUT ⎤⎥ f L VIN ⎦ × ⎣ ⎦ ⎣ Having a lower ripple current reduces the ESR losses in the output capacitors and the output voltage ripple. Highest efficiency operation is achieved at low frequency with small ripple current. This, however, requires a large inductor. A reasonable starting point for selecting the ripple current is ΔIL = 0.4(IMAX). The largest ripple current occurs at the highest VIN. To guarantee that the ripple current stays below a specified maximum, the inductor value should be chosen according to the following equation : ⎡ VOUT ⎤ ⎡ VOUT ⎤ L= ⎢ ⎥ × ⎢1 − VIN(MAX) ⎥ f I × Δ L(MAX) ⎣ ⎦ ⎣ ⎦ Inductor Core Selection Once the value for L is known, the type of inductor must be selected. High efficiency converters generally cannot afford the core loss found in low cost powdered iron cores, forcing the use of more expensive ferrite or mollypermalloy cores. Actual core loss is independent of core size for a fixed inductor value but it is very dependent on the inductance selected. As the inductance increases, core losses decrease. Unfortunately, increased inductance requires more turns of wire and therefore copper losses will increase. Ferrite designs have very low core losses and are preferred at high switching frequencies, so design goals can concentrate on copper loss and preventing saturation. Ferrite core material saturates “hard”, which means that inductance collapses abruptly when the peak design Copyright © 2012 Richtek Technology Corporation. All rights reserved. DS8080-00 July 2012 Different core materials and shapes will change the size/ current and price/current relationship of an inductor. CIN and COUT Selection The input capacitance, C IN, is needed to filter the trapezoidal current at the source of the top MOSFET. To prevent large ripple voltage, a low ESR input capacitor sized for the maximum RMS current should be used. RMS current is given by : V IRMS = IOUT(MAX) OUT VIN VIN −1 VOUT This formula has a maximum at VIN = 2VOUT, where I RMS = I OUT/2. This simple worst-case condition is commonly used for design because even significant deviations do not offer much relief. Note that ripple current ratings from capacitor manufacturers are often based on only 2000 hours of life which makes it advisable to further derate the capacitor, or choose a capacitor rated at a higher temperature than required. Several capacitors may also be paralleled to meet size or height requirements in the design. The selection of COUT is determined by the Effective Series Resistance (ESR) that is required to minimize voltage ripple and load step transients, as well as the amount of bulk capacitance that is necessary to ensure that the control loop is stable. Loop stability can be checked by viewing the load transient response as described in a later section. The output ripple, ΔVOUT, is determined by : 1 ⎤ ΔVOUT ≤ ΔIL ⎡⎢ESR+ 8fCOUT ⎥⎦ ⎣ is a registered trademark of Richtek Technology Corporation. www.richtek.com 11 RT8080 Using Ceramic Input and Output Capacitors Thermal Considerations Higher values, lower cost ceramic capacitors are now becoming available in smaller case sizes. Their high ripple current, high voltage rating and low ESR make them ideal for switching regulator applications. However, care must be taken when these capacitors are used at the input and output. When a ceramic capacitor is used at the input and the power is supplied by a wall adapter through long wires, a load step at the output can induce ringing at the input, VIN. At best, this ringing can couple to the output and be mistaken as loop instability. At worst, a sudden inrush of current through the long wires can potentially cause a voltage spike at VIN large enough to damage the part. The maximum power dissipation depends on the thermal resistance of IC package, PCB layout, the rate of surroundings airflow and temperature difference between junction to ambient. The maximum power dissipation can be calculated by following formula : The resistive divider allows the FB pin to sense a fraction of the output voltage as shown in Figure 1. VOUT R1 FB RT8080 R2 GND Figure 1. Setting the Output Voltage For adjustable voltage mode, the output voltage is set by an external resistive divider according to the following equation : VOUT = VREF ⎛⎜ 1+ R1 ⎞⎟ ⎝ R2 ⎠ where VREF is the internal reference voltage (0.6V typ.) Where T J(MAX) is the maximum operation junction temperature, TA is the ambient temperature and the θJA is the junction to ambient thermal resistance. For recommended operating condition specifications, the maximum junction temperature is 125°C. The junction to ambient thermal resistance, θJA, is layout dependent. For WDFN-6L 2x2 packages, the thermal resistance θJA is 120°C/W on the standard JEDEC 51-7 four layers thermal test board. The maximum power dissipation at TA = 25°C can be calculated by following formula : PD(MAX) = (125°C − 25°C) / 120°C/W = 0.833W for WDFN-6L 2x2 packages The maximum power dissipation depends on the operating ambient temperature for fixed T J(MAX) and thermal resistance, θJA. The derating curve in Figure 2 of derating curves allows the designer to see the effect of rising ambient temperature on the maximum power allowed. 1.0 Maximum Power Dissipation (W)1 Output Voltage Programming PD(MAX) = (TJ(MAX) − TA) / θJA Four-Layers PCB 0.8 0.6 0.4 0.2 0.0 0 25 50 75 100 125 Ambient Temperature (°C) Figure 2. Derating Curve of Maximum Power Dissipation Copyright © 2012 Richtek Technology Corporation. All rights reserved. www.richtek.com 12 is a registered trademark of Richtek Technology Corporation. DS8080-00 July 2012 RT8080 Layout Considerations NC 1 6 FB EN 2 5 GND VIN 3 4 LX Output capacitor must be near RT8080 L1 R1 COUT CIN CIN must be placed between VDD and GND as closer as possible LX should be connected to Inductor by wide and short trace, keep sensitive components away from this trace R2 Figure 3. PCB Layout Guide Layout note : 1. The distance that CIN connects to VIN is as close as possible (Under 2mm). 2. COUT should be placed near RT8080. Table 2. Recommended Inductors Inductance Current Rating (mA) (μH) Supplier DCR (mΩ) Dimensions (mm) Series TAIYO YUDEN 2.2 1480 60 3.00 x 3.00 x 1.50 NR 3015 GOTREND 2.2 1500 58 3.85 x 3.85 x 1.80 GTSD32 Sumida 2.2 1500 75 4.50 x 3.20 x 1.55 CDRH2D14 Table 3. Recommended Capacitors for CIN and C OUT Supplier Capacitance (μF) Package Part Number TDK 4.7 603 C1608JB0J475M MURATA 4.7 603 GRM188R60J475KE19 TAIYO YUDEN 4.7 603 JMK107BJ475RA TAIYO YUDEN 10 603 JMK107BJ106MA TDK 10 805 C2012JB0J106M MURATA 10 805 GRM219R60J106ME19 MURATA 10 805 GRM219R60J106KE19 TAIYO YUDEN 10 805 JMK212BJ106RD Copyright © 2012 Richtek Technology Corporation. All rights reserved. DS8080-00 July 2012 is a registered trademark of Richtek Technology Corporation. www.richtek.com 13 RT8080 Outline Dimension D2 D L E E2 1 e b A A1 SEE DETAIL A 2 1 2 1 A3 DETAIL A Pin #1 ID and Tie Bar Mark Options Note : The configuration of the Pin #1 identifier is optional, but must be located within the zone indicated. Dimensions In Millimeters Dimensions In Inches Symbol Min Max Min Max A 0.700 0.800 0.028 0.031 A1 0.000 0.050 0.000 0.002 A3 0.175 0.250 0.007 0.010 b 0.200 0.350 0.008 0.014 D 1.950 2.050 0.077 0.081 D2 1.000 1.450 0.039 0.057 E 1.950 2.050 0.077 0.081 E2 0.500 0.850 0.020 0.033 e L 0.650 0.300 0.026 0.400 0.012 0.016 W-Type 6L DFN 2x2 Package Richtek Technology Corporation 5F, No. 20, Taiyuen Street, Chupei City Hsinchu, Taiwan, R.O.C. Tel: (8863)5526789 Richtek products are sold by description only. Richtek reserves the right to change the circuitry and/or specifications without notice at any time. Customers should obtain the latest relevant information and data sheets before placing orders and should verify that such information is current and complete. Richtek cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Richtek product. Information furnished by Richtek is believed to be accurate and reliable. However, no responsibility is assumed by Richtek or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Richtek or its subsidiaries. www.richtek.com 14 DS8080-00 July 2012