SANKEN ELECTRIC CO., LTD. SFA0002-VF

SANKEN ELECTRIC CO., LTD.
SFA0002-VF-RP
1 Scope
The present specifications shall apply to switching power supply IC SFA0002-VF-RP.
2 Outline
Type
Semiconductor IC (Monolithic IC)
Structure
Plastic package (Transfer mold)
Features
Built-in current limit protection, thermal shutdown protection.
Built-in error-amp helps eliminate components at sensing stage such as
shunt regulator.
3 Absolute maximum ratings
3-1
Absolute maximum ratings (Ta=25°C)
Parameter
Symbol
Ratings
Unit
VOCP
-5~+5
V
SS terminal voltage
VSS
-0.3~+9
V
FB terminal voltage
VFB
-0.3~+5
V
Input voltage for control part
VCC
0~36
V
Phase compensation terminal voltage
VCOMP
-0.3~+5
V
Frequency setting terminal voltage
VFREQ
-0.3~+5
V
IDRV(peak)
-540mA~+270mA
mA
IDRV(DC)
-180mA~+90mA
mA
Power dissipation
PD
1.2 (※1)
W
Junction temperature
Tj
-40~150
℃
Storage temperature
Tstg
-40~150
℃
OCP terminal voltage
Drive terminal peak current
Drive terminal DC current
(※1)Mounted on glass epoxy board (The dimension of PCB : 42mm×32mm×1mmt)
3-2
Recommended operating conditions
Parameter
Input voltage for control part
Switching frequency
130529
Symbol
Ratings
Unit
VCC
6~24
V
FOSC
20~200
kHz
SSJ-04244
1/13
61426-01
SANKEN ELECTRIC CO., LTD.
SFA0002-VF-RP
4 Electrical characteristic
4-1Electrical characteristics (VCC=14V, Ta=-40~125°C) (*1)
Parameter
Symbol
MIN
Ratings
TYP
MAX
Conditions
Unit
Power supply Start-up Operation
Operation start voltage
VCC(ON)
4.9
5.1
5.3
V
Operation stop voltage
VCC(OFF)
4.4
4.6
4.8
V
Circuit current in operation
ICC(ON)
1
2
3.2
mA
Circuit current in non-operation
ICC(OFF)
0.3
0.5
1
mA
SS terminal high threshold voltage
VHSS
1.9
2
2.1
V
SS terminal low threshold voltage
VLSS
0.9
1
1.1
V
SS terminal voltage hysteresis width
Δ VSS
0.9
1
1.1
V
SS terminal outflow current
Isrc(SS)
11
15
19
uA
SS terminal inflow current
Isnk(SS)
13
17
21
uA
Switching frequency
fosc(200p)
85
100
115
kHz
FREQ terminal outflow current
Isrc(FREQ)
27
30
33
uA
FREQ terminal inflow current
Isnk(FREQ)
75
85
95
uA
Oscillation circuit high threshold voltage
VHF
1.9
2
2.1
V
Oscillation circuit low threshold voltage
VLF
0.9
1
1.1
V
Maximum on-duty width
Dmax
70
74
78
%
Slope compensation rate
SLP
2.1
2.5
2.9
mV/%
Feedback voltage
VFB
2.45
2.5
2.55
V
Burst threshold voltage
Vburst
-
0.18
-
V
Drive voltage
Vdrive
7.6
8.3
9
V
Vdrive(min)
4
Ton(min)
-
FB=0V、SS=0V、OCP=0V、FREQ=200pF
VCC=0V→14V
FB=0V、SS=0V、OCP=0V、FREQ=200pF
VCC=14V→0V
FB=0V、SS=0V、OCP=0V、FREQ=200pF、
VCC=14V
FB=0V、SS=0V、OCP=0V、FREQ=200pF、
VCC=4.8V
Normal Operation
Minimam drive voltage
Minimum on-time
V
170
-
ns
FB=0V、OCP=0V、FREQ=0V、VCC=14V、
SS=0V→2.5V
FB=0V、OCP=0V、FREQ=0V、VCC=14V、
SS=2.5V→0V
VHSS-VLSS
FB=0V、OCP=0V、FREQ=0V、VCC=14V、
SS=0.9V
FB=0V、OCP=0V、FREQ=0V、VCC=14V、
SS=2.1V
FB=0V、SS=0V、OCP=0V、FREQ=200pF、
VCC=14V
FB=0V、OCP=0V、SS=0V、VCC=14V、
FREQ=0.9V
FB=0V、OCP=0V、SS=0V、VCC=14V、
FREQ=2.1V
FB=0V、OCP=0V、SS=0V、VCC=14V、
FREQ=0V→2.5V
FB=0V、OCP=0V、SS=0V、VCC=14V、
FREQ=2.5V→0V
FB=0V、SS=0V、OCP=0V、FREQ=200pF、
VCC=14V
FB=0V、COMP=1.3V、SS=2.5V、
FREQ=200pF、VCC=14V、OCP=0V→1V
SS=0V、OCP=0V、FREQ=0V、VCC=14V
FB=0V→2.5V
SS=2.5V、FREQ=200pF、VCC=14V、
OCP=0V、COMP=0V→1V
FB=0V、OCP=0V、SS=0V、VCC=14V
FREQ=3V・1pluse
FB=0V、OCP=0V、SS=0V、VCC≧6V
FREQ=3V・1pluse
FB=0V、SS=0V、OCP=1V、Drv=680pF、
VCC=14V
Protection Operation
*1
The ratings at Ta=-40°C to 125°C shall be treated as a design value.
The ratings of devices shall be checked at -30°C, 25°C, 125°C at Outgoing Inspection.
*2
The rating of devices shall be treated as a design value.
130529
SSJ-04244
2/13
61426-01
SANKEN ELECTRIC CO., LTD.
4-2
SFA0002-VF-RP
Typical characteristics (Ta=25°C)
fosc(200p)[kHz]
fosc[kHz]
1000
100
10
10
100
1000
10000
115
112
109
106
103
100
97
94
91
88
85
-50
0
9
8
7
6
5
4
3
2
1
0
0
5
10
15
20
25
VCC[V]
ICC[mA]
50
100
150
100
150
Ta[℃ ]
VFB[V]
Vdrive[V]
CFREQ[pF]
2.55
2.54
2.53
2.52
2.51
2.5
2.49
2.48
2.47
2.46
2.45
-50
0
50
Ta[℃ ]
4
3.5
3
2.5
2
1.5
1
0.5
0
0
5
10
15
20
25
VCC[V]
5 Block diagram
130529
SSJ-04244
3/13
61426-01
SANKEN ELECTRIC CO., LTD.
SFA0002-VF-RP
6 Standard connection
※Since the switching noise caused by Q1 may affect the operation of an IC ,appropriate design for peripheral circuits is
required to prevent the malfunction of an IC by adding snubber circuit and /or filter circuit.
7 Pins function description
130529
Terminal No
symbols
Descripton
1
VCC
Power supply terminal
2
FB
Feedback terminal
3
GND
Ground terminal
4
SS
Soft start terminal
5
FREQ
Frequency setting terminal
6
COMP
Phase compensation terminal
7
Drive
Gate drive terminal
8
OCP
Over current protection terminal
SSJ-04244
4/13
61426-01
SANKEN ELECTRIC CO., LTD.
SFA0002-VF-RP
8 Timing diagram
8-1 Timing diagram in standard connection
Startup transient operation
Start
Steady operation
Softstart
Stop at light
load
Stop
Shift to intermittent operation when COMP terminal is below Vburst
*Intermittent operation (on width, period, etc.) depends on application
circuit.
8-2 Timing diagram in protection
Protected by OCP
Overcurrent state
130529
Released from
OLP operation
Stop Dvr terminal operation by
external input to SS terminal
SSJ-04244
5/13
61426-01
SANKEN ELECTRIC CO., LTD.
SFA0002-VF-RP
9 Package information
9-1Package type, physical dimensions and material
※1:Type Number
※2:Logo Mark
※3:Lot Number
1st letter:The Last digit of year
2nd leatter:Month
(1 to 9 Jan. to Sept.,O for Oct. N for Nov. D for Dec.)
3rd & 4th letter:day
01 to 31 Arabic Numeral
※4:Administer number
SFA0002 ※1
SK
※2
※3
※4
Dimensions in mm
Lead is solder-plated
(except cutting surface of lead)
Zoom of A part
Terminal No
symbols
Descripton
1
VCC
Power supply terminal
2
FB
Feedback terminal
3
GND
Ground terminal
4
SS
Soft start terminal
5
FREQ
Frequency setting terminal
6
COMP
Phase compensation terminal
7
Drive
Gate drive terminal
8
OCP
Over current protection terminal
9-2
Appearance
The body shall be clean and shall not bear any stain, rust or flaw.
9-3
Marking
The type number and lot number shall be legitimately marked in order not to be erased easily.
130529
SSJ-04244
6/13
61426-01
SANKEN ELECTRIC CO., LTD.
SFA0002-VF-RP
The example of the solder pattern
L
L
b2
I2
e1
e1
β1
e
b
e
e
L
β2
α
e
e
e
記号
寸法(mm)
Symbol
Dimensions(mm)
e1
5.72
e
1.27
or more
α
0.2以上
β1
0.2~0.5
β2
0.2
L
0.6
b
0.42
b2
0.76
L+β1+β2
I2
There are reference value that are according
with the EIAJ standards. (ED-7402-1)
130529
SSJ-04244
7/13
61426-01
SANKEN ELECTRIC CO., LTD.
SFA0002-VF-RP
SOP8 Taping specifications for packing
1.
General Description
This specification specifies packaging spec. for Sanken electric co., SFA0002-VF-RP as well as its
related matters. Shipping is only taping as to SOP8.
2. Part name indication
This followings specifies part name for taping spec.
2.1 Part name indication method
“Part name” - VF
2.2 IC direction in carrier tape pocket
SFA0002-VF-RP is [VF type].
End of “Part name” is [- VB]: 1 pin of IC is facing to tape roll-in direction.
End of “Part name” is [- VF]: 1 pin of IC is facing to tape pull-out direction.
3.
Embossed taping specifications
3.1 Taping type and physical dimensions
This carrier tape is treated antistatic treatment.
1Pin
Pull-Out
direction
Material:Emboss
130529
SSJ-04244
8/13
61426-01
SANKEN ELECTRIC CO., LTD.
3.2
SFA0002-VF-RP
Reeling type and physical dimensions
This reel is made of plastic with antistatic treatment.
A label shall be put on a side of flange.
quantity, and lot number.
A label has part number including a direction for unreeling,
Note
Reel Material:Plastic
Label content
NAME
LOT
No.
AMOUNT
SANKEN ELECTRIC CO.,LTD
130529
P・C・S
SSJ-04244
9/13
61426-01
SANKEN ELECTRIC CO., LTD.
3.3
SFA0002-VF-RP
Reeling specifications (Leader/Trail)
Adhesive tape
Cover tape section
Empty carrier tape
Trail
Leader
Leader
3.4
Leader
Cover tape section
Empty carrier tape
Leader Section
MIN 100mm
MIN 320mm
MIN 420mm
Trail
Empty carrier tape
MIN
80mm
Strength of taping seal
Detachment Strength of cover tape 0.1~1.0N
Tear away angle: 165~180° Detachment speed: 300±10mm/min
Cover tape
Tape feed direction
3.5
130529
Carrier tape
Missed parts on tape
The number of missed parts cannot exceed 0.1% of total parts on the tape.
parts must not happen.
Also, missing of sequential
SSJ-04244
10/13
61426-01
SANKEN ELECTRIC CO., LTD.
4.
Packaging
4.1 The number of parts per a reel: 3000 parts (MAX)
4.2 Indication of part name and quantity
A label shows part number, quantity, and lot number.
4.3
5.
SFA0002-VF-RP
Outer packaging of reel
Reel is put into moisture barrier bag and seal with desiccant and put into outer box.
Packing Dimensions and Appearance (A box is made of card boards.
The following dimensions are reference value.)
345
336
Dimensions of a box: H336mm x V345mm x T 40mm
233
357
Size of a box contains 5 small boxes: 357mm x 357x 233mm
130529
SSJ-04244
11/13
61426-01
SANKEN ELECTRIC CO., LTD.
SFA0002-VF-RP
6. Dry Pack
Moisture Barrier Bag
Humidity Indicator Card
Reel
Desiccant
7. Dry pack handling
This product is compliant with Moisture Sensitivity Level 3 (Conform to IPC/JEDEC J-STD-033).
This product should be handled as described below.
7.1 Calculated Shelf life in sealed bag: 12 months at <40°C and <90% relative humidity (RH)
7.2 After opening the bag, the infrared reflow, vapor-phase reflow,
or equivalent processing ( package body peak temp, 260°C) is possible under the conditions as follows:
a) Mounted within 168 hours under the condition of <30°C / 60% RH, or
b) Stored at <10% RH
7.3 Baking is required if
a) the humidity indicator indicates >10% at 23°C±5°C and
b) the storage environment is different from that of 7.2-a) and b) described above
7.4 The product should be taken out of the reel and emboss tape, and 48-hour baking at 125±5°C is required.
It is recommended to do baking one time immediately before use. The solderability should be checked when the
baking is done two times or more.
130529
SSJ-04244
12/13
61426-01
SANKEN ELECTRIC CO., LTD.
SFA0002-VF-RP
CAUTION/ WARNING
130529

Application and operation examples described in this document are quoted for the sole purpose of reference for the use of
the products herein and Sanken can assume no responsibility for any infringement of industrial property rights, intellectual
property rights or any other rights of Sanken or any third party which may result from its use.

Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of
semiconductor products at a certain rate is inevitable. Users of Sanken products are requested to take, at their own risk,
preventative measures including safety design of the equipment or systems against any possible injury, death, fires or
damages to the society due to device failure or malfunction.

Sanken products listed in this document are designed and intended for the use as components in general purpose electronic
equipment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.).
Please return to us this document with your signature(s) or seal(s) prior to the use of the products herein.
When considering the use of Sanken products in the applications where higher reliability is required (transportation
equipment and its control systems, traffic signal control systems or equipment, fire/crime alarm systems, various safety
devices, etc.), please contact your nearest Sanken sales representative to discuss, and then return to us this document with
your signature(s) or seal(s) prior to the use of the products herein.
The use of Sanken products without the written consent of Sanken in the applications where extremely high reliability is
required (aerospace equipment, nuclear power control systems, life support systems, etc.) is strictly prohibited.

In the case that you use our semiconductor devices or design your products by using our semiconductor devices, the
reliability largely depends on the degree of derating to be made to the rated values. Derating may be interpreted as a case that
an operation range is set by derating the load from each rated value or surge voltage or noise is considered for derating in
order to assure or improve the reliability. In general, derating factors include electric stresses such as electric voltage, electric
current, electric power etc., environmental stresses such as ambient temperature, humidity etc. and thermal stress caused due
to self-heating of semiconductor devices. For these stresses, instantaneous values, maximum values and minimum values
must be taken into consideration.
In addition, it should be noted that since power devices or IC’s including power devices have large self-heating value, the
degree of derating of junction temperature (Tj) affects the reliability significantly.

When using the products specified herein by either (i) combining other products or materials therewith or (ii) physically,
chemically or otherwise processing or treating the products, please duly consider all possible risks that may result from all
such uses in advance and proceed therewith at your own responsibility.

Anti radioactive ray design is not considered for the products listed herein.

Sanken assumes no responsibility for any troubles, such as dropping products caused during
transportation out of Sanken’s distribution network.
SSJ-04244
13/13
61426-01