CY8C201A0 CapSense Express™ -10 Configurable IOs with Slider Features Overview ■ The CapSense ExpressTM controller allows the control of 10 IOs configurable as capacitive sensing buttons or as GPIOs for driving LEDs or interrupt signals based on various button conditions. The GPIOs are also configurable for waking up the device from sleep based on an interrupt input. 10 configurable IOs supporting ❐ CapSense slider ❐ LED drive ❐ Interrupt outputs ❐ WAKE on interrupt input ❐ User defined input or output ■ 2.4V to 5.25V operating voltage ■ Industrial temperature range: –40°C to +85°C ■ I2C slave interface for configuration ❐ Selectable to 50 kHz,100 kHz and 400 kHz. ■ Reduce BOM cost ❐ Internal oscillator - no external oscillators or crystal ❐ Free development tool - no external tuning components ■ Low operating current ❐ Active current: continuous sensor scan: 1.5 mA ❐ Sleep current: no scan, continuous sleep: 2.6 uA ■ Available in 16-pin COL and 16-pin SOIC packages The user has the ability to configure buttons, outputs, and parameters, through specific commands sent to the I2C port. The IOs have the flexibility in mapping to capacitive buttons and as standard GPIO functions such as interrupt output or input, LED drive and digital mapping of input to output using simple logical operations. This enables easy PCB trace routing and reduces the PCB size and stack up. CapSense Express products are designed for easy integration into complex products. Architecture The logic block diagram shows the internal architecture of CY8C201A0. The user can configure registers with parameters needed to adjust the operation and sensitivity of the CapSense system. CY8C201A0 supports a standard I2C serial communication interface that allows the host to configure the device and to read sensor information in real time through easy register access. The CapSense Express Core The CapSense Express Core has a powerful configuration and control block. It encompasses SRAM for data storage, an interrupt controller, sleep and watchdog timers. System resources provide additional capability, such as a configurable I2C slave communication interface and various system resets. The Analog System is composed of the CapSense PSoC block which supports capacitive sensing of up to 10 inputs. Cypress Semiconductor Corporation Document Number: 001-17349 Rev. *B • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised March 11, 2008 [+] Feedback CY8C201A0 Logic Block Diagram E x te rn a l V C C 2 .4 -5 .2 5 V 10 Configurable IOs CapSense ExpressTM Core 2KB Flash 512B SRAM Document Number: 001-17349 Rev. *B Page 2 of 12 [+] Feedback CY8C201A0 Pinouts Figure 1. Pin Diagram - 16 COL Table 1. Pin Definitions - 16 COL Pin Number Name 1 GP0[0] Configurable as CapSense or GPIO 2 GP0[1] Configurable as CapSense or GPIO 3 I2C SCL I2C clock 4 I2C SDA I2C data 5 GP1[0] Configurable as CapSense or GPIO 6 GP1[1] Configurable as CapSense or GPIO 7 VSS 8 GP1[2] Configurable as CapSense or GPIO 9 GP1[3] Configurable as CapSense or GPIO 10 GP1[4] Configurable as CapSense or GPIO 11 XRES Active HIGH external reset with internal pull down 12 GP0[2] Configurable as CapSense or GPIO 13 VDD 14 GP0[3] 15 CSInt 16 GP0[4] Document Number: 001-17349 Rev. *B Description Ground connection Supply voltage Configurable as CapSense or GPIO Integrating Input. The external capacitor is required only if 5:1 SNR cannot be achieved.Typical range is 10 nf to 100 nf. Configurable as CapSense or GPIO Page 3 of 12 [+] Feedback CY8C201A0 Figure 2. Pin Diagram - 16 SOIC GP0[3] 1 16 VDD CSInt 2 15 GP0[2] GP0[4] 3 14 XRES GP0[0] 4 13 GP1[4] GP0[1] 5 12 GP1[3] I2CSCL 6 11 GP1[2] I2CSDA 7 10 VSS GP1[0] 8 9 SOIC (Top View) GP1[1] Table 2. Pin Definitions - 16 SOIC Pin Number Name 1 GP0[3] 2 CSInt 3 GP0[4] Configurable as CapSense or GPIO 4 GP0[0] Configurable as CapSense or GPIO 5 GP0[1] Configurable as CapSense or GPIO 6 I2C SCL I2C clock 7 I2C SDA I2C data 8 GP1[0] Configurable as CapSense or GPIO 9 GP1[1] Configurable as CapSense or GPIO 10 VSS 11 GP1[2] Configurable as CapSense or GPIO 12 GP1[3] Configurable as CapSense or GPIO 13 GP1[4] Configurable as CapSense or GPIO 14 XRES Active HIGH external reset with internal pull down. 15 GP0[2] Configurable as CapSense or GPIO 16 VDD Document Number: 001-17349 Rev. *B Description Configurable as CapSense or GPIO Integrating Input. The external capacitor is required only if 5:1 SNR cannot be achieved.Typical range is 10nf to 100nf. Ground connection Supply voltage Page 4 of 12 [+] Feedback CY8C201A0 The CapSense Analog System I2C Interface The CapSense analog system contains the capacitive sensing hardware which supports the CapSense Successive Approximation (CSA) algorithm. This hardware performs capacitive sensing and scanning without external components. Capacitive sensing is configurable on each pin. The two modes of operation for the I2C interface are: Additional System Resources The I2C address is programmable during configuration. It can be locked to prevent accidental change by setting a flag in a configuration register. System resources provide additional capability useful to complete systems. Additional resources are low voltage detection and power on reset. Brief statements describing the merits of each system resource are: ■ The I2C slave provides 50, 100, or 400 kHz communication over two wires. ■ Low Voltage Detection (LVD) interrupts can signal the application of falling voltage levels and the advanced POR (Power On Reset) circuit eliminates the need for a system supervisor. ■ Device register configuration and status read or write for controller ■ Command execution CapSense Express Software Tool An easy to use software tool integrated with PSoC Express is available for configuring and tuning CapSense Express devices.Refer to the Application Note AN42137 for details of the software tool. CapSense Express Register Map CapSense Express supports user configurable registers through which the device functionality and parameters are configured. For details, refer to CY8C201xx Register Reference document. An internal 1.8V reference provides a stable internal reference so that capacitive sensing functionality is not affected by minor VDD changes. Electrical Specifications Absolute Maximum Ratings Min Typ Max Unit TSTG Parameter Storage temperature Description –55 25 +100 °C TA Ambient temperature with power applied –40 – +85 °C VDD Supply voltage on VDD relative to VSS –0.5 – +6.0 V VIO DC input voltage VSS – 0.5 – VDD + 0.5 V VIOZ DC voltage applied to tri-state VSS – 0.5 – VDD + 0.5 V IMIO Maximum current into any GPIO pin –25 – +50 mA ESD Electro static discharge voltage 2000 – – V LU Latch up current – – 200 mA Min Typ Max Unit Notes Higher storage temperatures reduce data retention time. Recommended storage temperature is +25°C ± 25°C (0°C to 50°C). Extended duration storage temperatures above 65°C degrade reliability. Human body model ESD Operating Temperature Parameter Description TA Ambient temperature -40 – +85 °C TJ Junction temperature -40 – +100 °C Document Number: 001-17349 Rev. *B Notes Page 5 of 12 [+] Feedback CY8C201A0 DC Electrical Characteristics DC Chip Level Specifications Parameter Description VDD Supply voltage Min Typ Max Unit 2.40 – 5.25 V Notes IDD Supply current – 1.5 2.5 mA Conditions are VDD = 3.0V, TA = 25°C ISB Sleep mode current with POR and LVD active. Mid temperature range – 2.6 4 µA VDD = 2.55V, 0°C < TA < 40°C ISB Sleep mode current with POR and LVD active. – 2.8 5 µA VDD = 3.3V, –40°C < TA < 85°C ISB Sleep mode current with POR and LVD active. – 5.2 6.4 µA VDD = 5.25V, –40°C < TA < 85°C 5V and 3.3V DC General Purpose IO Specifications This table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25Vand -40C<TA<85C, 3.0V to 3.6V -40°C<TA<85°C. Typical parameters apply to 5v and 3.3V at 25°C and are for design guidance only. Parameter Description Min Typ Max Unit Notes RPU Pull up resistor 4 5.6 8 kΩ VOH1 High output voltage Port 0 pins VDD – 0.2 – – V IOH < 10 µA, VDD > 3.0V, maximum of 20 mA source current in all IOs. VOH2 High output voltage Port 0 pins VDD – 0.9 – – V IOH = 1 mA, VDD > 3.0V, maximum of 20 mA source current in all IOs. VOH3 High output voltage Port 1 pins VDD – 0.2 – – V IOH < 10 µA, VDD> 3.0V, maximum of 10 mA source current in all IOs. VOH4 High output voltage Port 1 pins VDD – 0.9 – – V IOH = 5 mA, VDD > 3.0V, maximum of 20 mA source current in all IOs. VOH5 High output voltage Port 1 pins with 3.0V LDO regulator enabled High Output Voltage Port 1 pins with 3.0V LDO regulator 2.75 3.0 3.2 V IOH < 10 µA, VDD> 3.1V, maximum of 4 IOs all sourcing 5mA. 2.2 – – V IOH = 5 mA, VDD > 3.1V, maximum of 20 mA source current in all IOs. VOH7 High Output Voltage Port 1 pins with 2.4V LDO regulator 2.1 2.4 2.5 V IOH < 10 µA, VDD > 3.0V, maximum of 20 mA source current in all IOs. VOH8 High Output Voltage Port 1 pins with 2.4V LDO regulator 2 – – V IOH < 200 µA, VDD > 3.0V, maximum of 20 mA source current in all IOs. VOL Low output voltage – – 0.75 V IOL = 20 mA, VDD > 3V, maximum of 60 mA sink current on even port pins and 60 mA sink current on odd port pins - .75 V VDD 3.0 to 3.6V V VDD 3.0 to 3.6V VOH6 VIL Input low voltage - VIH Input high voltage 1.6 VIL Input low voltage – – 0.8 V VDD = 3.6 to 5.25V. VIH Input high voltage 2.0 – – V VDD = 3.6 to 5.25V. VH Input hysteresis voltage – 140 – mV IIL Input leakage – 1 – nA Gross tested to 1 µA. CIN Capacitive load on pins as input 0.5 1.7 5 pF Package and pin dependent. Temp = 25°C. COUT Capacitive load on pins as output 0.5 1.7 5 pF Package and pin dependent. Temp = 25°C. Document Number: 001-17349 Rev. *B Page 6 of 12 [+] Feedback CY8C201A0 2.7 DC General Purpose IO Specifications This table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges:2.4V to 3.0V and -40°C<TA<85°C, respectively. Typical parameters apply to 2.7V at 25°C and are for design guidance only. Parameter Description Min Typ Max Unit Notes RPU Pull up resistor 4 5.6 8 kΩ VOH1 High output voltage Port 0 pins VDD – 0.2 – – V IOH < 10 µA, maximum of 10 mA source current in all IOs. VOH2 High output voltage Port 0 pins VDD – 0.5 – – V IOH = 0.2 mA, maximum of 10 mA source current in all IOs. VOH3 High output voltage Port 1 pins VDD – 0.2 – – V IOH < 10 µA, maximum of 10 mA source current in all IOs. VOH4 High output voltage Port 1 pins VDD – 0.5 – – V IOH = 2 mA, maximum of 10 mA source current in all IOs. VOL Low output voltage – – 0.75 V IOL = 10 mA, maximum of 30 mA sink current on even port pins and 30 mA sink current on odd port pins VOLP1 Low output voltage port 1 pins – – 0.4 V IOL=5mA Maximum of 50mA sink current on even port pins and 50mA sink current on odd port pins 2.4<VDD<3.6V VIL Input low voltage – – 0.75 V VDD= 3.0 to 3.6V VIH Input high voltage 1.6 – – V VDD= 3.0 to 3.6V VIL Input low voltage – – 0.75 V VDD = 2.4 to 3.6V. VIH1 Input high voltage 1.4 – – V VDD = 2.4 to 2.7V. VIH2 Input high voltage 1.6 – – V VDD = 2.7 to 3.6V VH Input hysteresis voltage – 60 – mV IIL Input leakage – 1 – nA Gross tested to 1 µA. CIN Capacitive load on pins as input 0.5 1.7 5 pF Package and pin dependent. Temp = 25°C. COUT Capacitive load on pins as output 0.5 1.7 5 pF Package and pin dependent. Temp = 25°C. Min Typ Max Unit DC POR and LVD Specifications Parameter Description VPPOR0 VPPOR1 VDD Value PPOR Trip VDD= 2.7V VDD= 3.3V,5V – – 2.36 2.60 2.40 2.65 V V VLVD0 VLVD2 VLVD6 VDD Value for LVD trip VDD= 2.7V VDD= 3.3V VDD= 5V 2.39 2.75 3.98 2.45 2.92 4.05 2.51 2.99 4.12 V V V Document Number: 001-17349 Rev. *B Notes VDD must be greater than or equal to 2.5V during startup, reset from the XRES pin, or reset from Watchdog. Page 7 of 12 [+] Feedback CY8C201A0 AC Electrical Characteristics 5.0V and 3.3V AC General Purpose IO Specifications Parameter Description Min Max Unit Notes TRise0 Rise time, strong mode, Cload = 50pF, Port 0 15 80 ns VDD = 3.0V to 3.6V and 4.75V to 5.25V, 10% - 90% TRise1 Rise time, strong mode, Cload = 50pF, Port 1 10 50 ns VDD = 3.0V to 3.6V, 10% - 90% TFall Fall time, strong mode, Cload = 50pF, all ports 10 50 ns VDD = 3.0V to 3.6V and 4.75V to 5.25V, 10% - 90% 2.7V AC General Purpose IO Specifications Min Max Unit TRise0 Parameter Rise time, strong mode, Cload = 50pF, Port 0 Description 15 100 ns VDD = 2.4V to 3.0V, 10% - 90% Notes TRise1 Rise time, strong mode, Cload = 50pF, Port 1 10 70 ns VDD = 2.4V to 3.0V, 10% - 90% TFall Fall time, strong mode, Cload = 50pF, all ports 10 70 ns VDD = 2.4V to 3.0V, 10% - 90% AC I2C Specifications Parameter Description Standard Mode Fast Mode Units Min Max Min Max 0 100 0 400 kbps THDSTAI2C Hold time (repeated) START condition. After this period, the first clock pulse is generated. 4.0 – 0.6 – µs TLOWI2C LOW period of the SCL clock 4.7 – 1.3 – µs I2C HIGH period of the SCL clock 4.0 – 0.6 – µs 4.7 – 0.6 – µs 0 – 0 – µs 250 – 100 – ns FSCLI2C THIGH SCL clock frequency 2 TSUSTAI C Setup time for a repeated START condition THDDATI2C Data hold time 2 TSUDATI C Data setup time 2 TSUSTOI C Setup time for STOP condition 4.0 – 0.6 – µs TBUFI2C BUS free time between a STOP and START condition 4.7 – 1.3 – µs TSPI2C Pulse width of spikes suppressed by the input filter – – 0 50 ns Document Number: 001-17349 Rev. *B Notes Fast mode not supported for VDD < 3.0V Page 8 of 12 [+] Feedback CY8C201A0 Figure 3. Definition for Timing for Fast/Standard Mode on the I2C Bus Document Number: 001-17349 Rev. *B Page 9 of 12 [+] Feedback CY8C201A0 Ordering Information Operating Temperature Ordering Code Package Diagram Package Type CY8C201A0-LDX2I 001-09116 16 COL[3] Industrial CY8C201A0-SX2I 51-85068 16 SOIC Industrial Thermal Impedances by Package Typical θJA[1] Package 16 COL [3] 46 °C 16 SOIC 79.96 °C Solder Reflow Peak Temperature Minimum Peak Temperature[2] Maximum Peak Temperature COL[3] 240 °C 260 °C 16 SOIC 240 °C 260 °C Package 16 Notes 1. TJ = TA + Power x θJA. 2. Higher temperatures may be required based on the solder melting point. Typical temperatures for solder are 220 ± 5°C with Sn-Pb or 245 ± 5°C with Sn-Ag-Cu paste. Refer to the solder manufacturer specifications. 3. Earlier termed as QFN package. Document Number: 001-17349 Rev. *B Page 10 of 12 [+] Feedback CY8C201A0 Package Diagram Figure 4. 16L Chip On Lead 3 X 3 mm Package Outline (SAWN) - 001-09116 - (Pb-Free) DIMENSIONS IN mm MIN. MAX. 2.9 3.1 0.20 min 0.45 0.55 1.5 (NOM) 1 2 2 2.9 3.1 1 0.152 REF. 0.20 DIA TYP. 0.05 MAX 0.60 MAX PIN #1 ID 0.30 0.18 0.50 SEATING PLANE TOP VIEW PART NO. LG16A LD16A SIDE VIEW 1.5 BOTTOM VIEW JEDEC # MO-220 Package Weight: 0.014g DESCRIPTION LEAD-FREE STANDARD 001-09116-*C Figure 5. 16 Pin (150-Mil) SOIC (51-85068) 51-85068-*B Document Number: 001-17349 Rev. *B Page 11 of 12 [+] Feedback CY8C201A0 Document History Page Document Title: CY8C201A0 CapSense Express™ -10 Configurable IOs with Slider Document Number: 001-17349 REV. ECN. Orig. of Change ** 1494145 TUP/AESA New Datasheet *A 1773608 TUP/AESA Removed table - 3V DC General Purpose IO Specifications Updated Logic Block Diagram Updated table - DC POR and LVD Specifications Updated table - DC Chip Level Specifications Updated table - 5V and 3.3V DC General Purpose IO Specifications Updated table - 2.7V DC General Purpose IO Specifications Updated table - AC GPIO Specifications and split it into two tables for 5V/3.3V and 2.7V Added section on CapSense ExpressTM Software tool Updated 16-QFN Package Diagram *B 2091026 DZU/MOHD /AESA Updated table-DC Chip Level Specifications Updated table-Pin Definitions 16 pin COL Updated table-Pin Definitions 16 pin SOIC Updated table-5V and 3.3V DC General Purpose IO Specifications Updated table - 2.7V DC General Purpose IO Specifications Changed definition for Timing for Fast/Standard Mode on the I2C Bus diagram Description of Change © Cypress Semiconductor Corporation, 2007-2008. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 001-17349 Rev. *B Revised March 11, 2008 Page 12 of 12 PSoC Designer™, Programmable System-on-Chip™, and PSoC Express™ are trademarks and PSoC® is a registered trademark of Cypress Semiconductor Corp. All other trademarks or registered trademarks referenced herein are property of the respective corporations. Purchase of I2C components from Cypress or one of its sublicensed Associated Companies conveys a license under the Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips. All products and company names mentioned in this document may be the trademarks of their respective holders. [+] Feedback