High Power Modules DC/DC Converters www.tracopower.com TEP-160WI Series 132 to 156 W pending High power density Full datasheet in progress ! Ultra wide 4:1 input voltage range % Soft start Reverse input protection I/O isolation 2250 VDC (basic insulation) Adjustable output voltage Shielded metal case with aluminium baseplate Optional adapter for screw terminal connection, chassis mount and for DIN-rail mount (Models pictured with chassis mount adapter and heat-sink) Models Order code Input voltage Output voltage Output current max. 3.3 VDC 5.0 VDC 40 A 28 A Line regulation 0.2% max. Load regulation 0.3 % max. Output voltage +10 % / -20 % adjustable by external resistor TEP 160-2410WI TEP 160-2411WI Ripple & noise (20 MHz BW) – 5 VDC output models: <75 mVpk-pk – other output models: <1 % of Vout TEP 160-2412WI TEP 160-2415WI 24 VDC 6.0 A continuous, automatic recovery TEP 160-2416WI 28 VDC 5.0 A TEP 160-2418WI 48 VDC 3.0 A TEP 160-4810WI TEP 160-4811WI 3.3 VDC 5.0 VDC 40 A 30 A 12 VDC 13 A TEP 160-2413WI Conducted EMI Short circuit protection Reverse input protection parallel diode 88 % typ. Operating temperature range –40 °C to +75°C with heat-sink for derating see datasheet TEP 160-4812WI Thermal protection shutdown at 115 °C TEP 160-4813WI 9 – 36 VDC 18 – 75 VDC 12 VDC 12 A 15 VDC 9.5 A 15 VDC 10 A I/O isolation test voltage 2250 VDC (basic insulation) TEP 160-4815WI 24 VDC 6.5 A Safety standards / approvals TEP 160-4816WI 28 VDC 5.5 A TEP 160-4818WI 48 VDC 3.2 A cUL/UL 60950-1, IEC/EN 60950-1, EN 50155 Options Casing shielded metal case with aluminium baseplate Remote On/Off shutdown input for low input current (3 mA) in standby operation DIN-rail mount optional adapter for cassis mount version: TEP-MK1 Heat-sink: Order code TEP-HS1 (separate order) -CM* Chassis mount adapter: -CMF* * Shipped assembled with converter module Dimensions TEP 160WI Module TEP 160WI Module with heat-sink 0.22 0.5 0.22 0.95 (5.6) (12.7) (5.6) (24.2) 0.19 (4.8) 1.90 (48.26) 4 x M3 THD (trough hole) 2 9 1.00 (25.40) 4 0.30 8 (7.62) 7 3 Pin TEP 160WI Module on (3.5) 0.14 1.31 (33.3) 1 2 – Vin (GND) Case 3 Remote On/Off 4 + Vin (Vcc) 5 – Vout 6 – Sense 7 Trim 8 + Sense 9 + Vout 4 x Ø 0.17 (4.3) 2.40 (61.0) 1.02 (25.9) 2.126 (54.0) (48.3) 1.90 () = mm 6 Bottom view 1.18 (30.0) 1.10 (28.0) 5 0.70 (17.78) 2.40 (61.0) TEP 160WI Module on Chassis mount adapter 2.00 (50.80) 1 3.071 (78.0) 3.35 (85.0) 0.14 (3.5) Download full datasheet at www.tracopower.com/products/tep160wi.pdf 79