DC/DC Converters THL 6WISM Series, 6 Watt CB Features ◆ Compact design in SMD package ◆ Ultra wide 4:1 input voltage range ◆ Fully regulated outputs ◆ I/O isolation 1500 VDC ◆ Operating temp. range –40°C to +75°C ◆ Short circuit protection ◆ Input filter to meet EN 55022, class A ◆ Qualified for leadfree reflow solder 226037 Scheme IEC 60950-1 process ◆ 3-year product warranty The THL 6WISM series is a family of compact 6 W dc/dc-converters with 4:1 input voltage ranges. The product is available in SMD-package which is 31% smaller than a standard DIP-24 package. The internal filter to meet EN55022 Class A without external components makes these converters easy to design in. They come with remote On/Off and short circuit protection. THL 6WISM converter is an excellent solution for data- and telecom applications and for instrumentation and industrial electronics. Models Order code Input voltage range THL 6-2410WISM Output voltage Output current max. Efficiency typ. 1450 mA 76 % 3.3 VDC THL 6-2411WISM 5.0 VDC 1200 mA 79 % THL 6-2412WISM 12 VDC 500 mA 83 % THL 6-2413WISM 9 – 36 VDC 15 VDC 400 mA 83 % THL 6-2415WISM (nominal 24 VDC) 24 VDC 250 mA 83 % ±5 VDC ±600 mA 82 % THL 6-2421WISM THL 6-2422WISM ±12 VDC ±250 mA 83 % THL 6-2423WISM ±15 VDC ±200 mA 83 % THL 6-4810WISM 3.3 VDC 1450 mA 76 % THL 6-4811WISM 5.0 VDC 1200 mA 79 % THL 6-4812WISM 12 VDC 500 mA 83 % THL 6-4813WISM 18 – 75 VDC 15 VDC 400 mA 83 % THL 6-4815WISM (nominal 48 VDC) 24 VDC 250 mA 83 % THL 6-4821WISM ±5 VDC ±600 mA 82 % THL 6-4822WISM ±12 VDC ±250 mA 83 % THL 6-4823WISM ±15 VDC ±200 mA 83 % http://www.tracopower.com Page 1 of 3 DC/DC Converters THL 6WISM Series 6 Watt Input Specifications Input current at no load (nominal input voltage) Input current at full load (nominal input voltage) 24 48 Surge voltage (100 msec. max.) 24 Vin models: 30 mA typ. 48 Vin models: 20 mA typ. Vin; 3.3 VDC model: 24 Vin other models: Vin; 3.3 VDC model: 48 Vin other models: 260 mA typ. 300 mA typ. 130 mA typ. 150 mA typ. 24 Vin models: 50 V max. 48 Vin models: 100 V max. Conducted noise EN 55022 level A, FCC part 15, level A without external components Recommended input fuse (slow blow) 24 V models: 1500 mA 48 V models: 750 mA Output Specifications Voltage set accuracy ±2 % max Regulation – Input variation Vin min. to Vin max. 1.0 % max. – Load variation 15 – 100 % 1.2 % max. Minimum load 15 % of rated max current (operation at lower load condition is safe but a higher output ripple will be experienced) Temperature coefficient ±0.02 %/K Ripple and noise (20 MHz bandwidth) 100 mVp-p max. Transient response setting time (25 % load step change) 300 µs typ. Short circuit protection indefinite Maximum capacitive load 3.3 & 5 VDC models: 330 µF 12, 15 & 24 VDC models: 100 µF ±5,±12 & ±15 VDC models: 100 µF (each output) General Specifications Temperature – Operating (convection cooling 50 LFM, 0.25 m/s) –40°C to +75°C – Storage –40°C to +125°C – Case +105°C max. Load derating (convection cooling 50 LFM, 0.25 m/s) 3.3 & 5.0 VDC models: 2.2 %/K above +55°C other output models: 2.5 %/K above +60°C Humidity (non condensing) 95 % Reliability, calculated MTBF (MIL-HDBK-217F, at +25°C, ground benign) >350‘000 h Isolation voltage (60 sec.) – Input/Output 1’500 VDC Isolation capacitance – Input/Output 1500 pF max. Isolation resistance – Input/Output (500 VDC) >1 GOhm Safety standard (designed to meet) IEC 60950-1, UL 60950-1 Safety approvals – CB test certificate according IEC 60950-1 www.tracopower.com/products/thl6wism-cb.pdf – CSA certificate for UL/cUL 60950-1 www.tracopower.com/products/thl6wism-csa.pdf Switching frequency 330 kHz Altitude during operation 5‘000 m max. (16‘400 ft) approved Remote On/Off – On: 2.5 to 50 VDC or open circuit – Off: –0.7 to +0.8 VDC – Off stand by input current 10 mA max. Environmental compliance – Reach www.tracopower.com/products/thl6wism-reach.pdf – RoHS RoHS directive 2002/95/EC All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 3 DC/DC Converters THL 6WISM Series 6 Watt Pysical Specifications Casing material non-conductive plastic (UL94V-0 rated) Weight 7.8 g (0.27oz) Lead-free reflow solder process for SMD-package models as per J-STD-020D.01 (to find at: www.jedec.org - free registration required) Moisture sensivity level (for SMD-package models) level 2a as per J-STD-033B.01 (to find at: www.jedec.org - free registration required) g Packaging www.tracopower.com /products/thl6wism-pack.pdf din n pe Washing process not recommended Application note: www.tracopower.com/products/thl6wism-application.pdf Outline Dimensions 5.08 2.54 2.11 (0.10) 2 20.3 (0.8) (0.08) (0.01) 1 16 10.05 (0.4) 10.16 (0.40) top view 6 11 1.5 (0.06) 22.0 (0.87) 0.15 (0.20) 8 9 Pin-Out 25.4 (1.0) Pin Single Dual 1 Remote On/Off Remote On/Off 2 –Vin –Vin 6 ntc. Common 8 ntc. –Vout 9 +Vout +Vout 11 –Vout Common +Vin (Vcc) +Vin (Vcc) 16 ntc. = not to connect Dimensions in [mm], () = Inch Tolerances: ±0.25 (±0.01) Pin pich tolerances: ±0.13 (±0.005) Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com www.tracopower.com Rev. January 05. 2015 Page 3 of 3