DC/DC Converters TEN 6N Series, 6 Watt C Bending p Scheme IEC 60950-1 Features ◆ 2:1 input voltage range ◆ High efficiency ◆ Operating temperature range UL 60950-1 -40°C to +85°C ◆ No minimum load required ◆ Input filter meets EN 55022, class A ◆ Overload protection ◆ I/O-isolation 1’500 VDC ◆ DIP-24 plastic package ◆ Industry standard pinout ◆ 3-year product warranty The TEN-6N series is designed for an optimized cost/performance ratio of DC/DC converters with output power of 6 Watt. General features like no minimum load requirement, overload protection, internal filter for EN55022 class A and high efficiency make these converters easy to design in. With the popular DIP-24 standard package they are also a drop in replacement for many cost critical applications. Models Order code Input voltage range Output voltage Output current max. Efficiency typ. 3.3 VDC 1200 mA 75 % 5 VDC 1200 mA 78 % 12 VDC 500 mA 82 % 400 mA 82 % TEN 6-1210N TEN 6-1211N TEN 6-1212N TEN 6-1213N 9 – 18 VDC 15 VDC TEN 6-1215N (12 VDC nominal) 24 VDC 250 mA 84 % TEN 6-1221N ±5 VDC ±500 mA 78 % TEN 6-1222N ±12 VDC ±250 mA 82 % TEN 6-1223N ±15 VDC ±200 mA 82 % TEN 6-2410N 3.3 VDC 1200 mA 77 % TEN 6-2411N 5 VDC 1200 mA 80 % TEN 6-2412N 12 VDC 500 mA 84 % TEN 6-2413N 18 – 36 VDC 15 VDC 400 mA 84 % TEN 6-2415N (24 VDC nominal) 24 VDC 250 mA 84 % TEN 6-2421N ±5 VDC ±500 mA 80 % TEN 6-2422N ±12 VDC ±250 mA 84 % TEN 6-2423N ±15 VDC ±200 mA 84 % TEN 6-4810N 3.3 VDC 1200 mA 77 % TEN 6-4811N 5 VDC 1200 mA 80 % TEN 6-4812N 12 VDC 500 mA 84 % TEN 6-4813N 36 – 75 VDC 15 VDC 400 mA 84 % TEN 6-4815N (48 VDC nominal) 24 VDC 250 mA 84 % TEN 6-4821N ±5 VDC ±500 mA 80 % TEN 6-4822N ±12 VDC ±250 mA 84 % TEN 6-4823N ±15 VDC ±200 mA 84 % http://www.tracopower.com Page 1 of 3 DC/DC Converters TEN 6N Series 6 Watt Input Specifications Input current at no load Input current at full load 12 24 48 12 Vin models: 40 mA typ. 24 Vin models: 20 mA typ. 48 Vin models: 10 mA typ. Vin, 3.3VDC 12 Vin other Vin, 3.3VDC 24 Vin other Vin, 3.3VDC 48 Vin other models: models: models: models: models: models: 440 mA typ. 610 mA typ. 220 mA typ. 300 mA typ. 110 mA typ. 150 mA typ. Recommended input fuse (slow blow) 12 Vin models: 1500 mA 24 Vin models: 700 mA 48 Vin models: 350 mA Start-up voltage / under voltage shut down 12 Vin models: 9.0 VDC / 8.5 VDC (or lower) 24 Vin models: 18 VDC / 16 VDC (or lower) 48 Vin models: 36 VDC / 35 VDC (or lower) Surge voltage (1 sec. max.) 12 Vin models: 25 V max. 24 Vin models: 50 V max. 48 Vin models: 100 V max. Conducted noise internal filter to meet EN 55022 class A Output Specifications Voltage set accuracy ±2 % Regulation – Input variation Vin min. to Vin max. – Load variation 0 – 100 % single output models: dual output models balanced load: dual output models 50%/100% unbalanced load: 0.5 % max. 1.2 % max. 1.2 % max. 3.0 % max. Minimum load not required Temperature coefficient ±0.02 %/K Ripple and noise (20 MHz Bandwidth) 80 mVp-p max. Dynamic load response (change from 75 % to 100 % load) ±3 % peak variation typ. 300 μS response time typ. Current limitation 145 % of Iout max. typ., constant power Short circuit protection continuous, automatic recovery Capacitive load 3.3 & 5.0 VDC 12 & 15 VDC 24 VDC dual output models: models: models: models: 470 µF max. 100 µF max. 47 µF max. 100 µF max. (each output) General Specifications Temperature ranges – Operating –40°C to +85°C – Case temperature +100°C max. – Storage –50°C to +125°C Derating 3.3 & 5.0 VDC models: 2.5 %/K above +60°C other models: 3.3 %/K above +70°C Humidity (non condensing) 95 % rel H max. Reliability, calculated MTBF (MIL-HDBK-217F, at +25°C, ground benign) >1 Mio. h Isolation voltage (60 sec.) – Input/Output 1’500 VDC (functional insulation) Isolation capacitance – Input/Output (100 KHz, 1 V) 1000 pF typ. Isolation resistance – Input/Output (500 VDC) >1‘000 M Ohm Switching frequency 330 kHz typ. All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 3 DC/DC Converters TEN 6N Series 6 Watt General Specifications Safety standards UL/cUL 60950-1, IEC/EN 60950-1 Safety approvals g – CSA certificate according UL 60950-1 www.tracopower.com/products/ten6n-csa.pdf din n – CB test certificate according IEC 60950-1 www.tracopower.com/products/ten6n-cb.pdf pe Environmental compliance – Reach www.tracopower.com/products/ten6n-reach.pdf – RoHS RoHS directive 2002/95/EC Physical Specifications Casing material non conductive plastic (UL 94V-0-rated) Potting material epoxy (XM-2109 & XY-2110, UL 94V-0-rated) Weight 4.8 g (0.16 oz) Soldering temperature (1.5mm from case for 10 sec.) max. 260°C Application note: www.tracopower.com/products/ten6n-application.pdf Outline Dimensions (0.60) Pin Single Dual 2 –Vin (GND) –Vin (GND) 3 –Vin (GND) –Vin (GND) (1.25) 4.1 4.5 (0.18) 2.54 (0.10) 15.24 (0.60) 9 No pin Common 11 No function –Vout 14 +Vout +Vout 16 –Vout Common 22 +Vin (Vcc) +Vin (Vcc) 23 +Vin (Vcc) +Vin (Vcc) (0.16) 10.2 (0.40) 31.8 (0.80) 14 2.54 16 15.24 Bottom view 23 22 Pin-Out 11 20.3 9 (0.10) 2 3 5.08 (0.20) Dimensions in [mm], () = Inch Pin diameter ø 0.5 ±0.05 (0.02 ±0.002) Tolerances ±0.25 (±0.01) Pin pich tolerances ±0.13 (±0.0005) Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com www.tracopower.com Rev. March 26. 2013 Page 3 of 3