Pilkor components PFC Input Capacitors Metallized Polypropylene film capacitors MKP LACQUERED CAPACITORS(Dipped Type)-Brown PCMP 392 (MPP) Pitch 10.0/15.0mm (reduced pitch;7.5mm) QUICK REFERENCE DATA Capacitance range (E12 series) 0.22 to 2.2㎌ Capacitance tolerance ±5%, ±10% Rated voltage (DC) 450V Climatic category 40/105/21 Temperature range -40℃ ~ +105℃ Reference specification IEC 60384-16 Coating Materials Qualified in accordance with UL94V-0 Passive flammability category to IEC 60065 Class B FEATURES APPLICATIONS . Low-noise . PFC Input Capacitor for LCD/PDP power . Self-healing properties . PFC Input Capacitor for LED lamp power . Low dissipation factor . Low ESR . Cell coated with flame resisting epoxy lacquer . Supplied loose in box . Miniature type of PCMP 472 series • Please refer to caution and warning at http://www.pilkor.co.kr/download/Introductions.pdf before using these products. 249 Pilkor components PFC Input Capacitors Metallized Polypropylene film capacitors PCMP 392 (MPP) Ordering Information Wmax Wmax Wmax Hmax Hmax 4.8±1.3㎜ 4.8±1.3㎜ F H0 lt lt lt Hmax Hmax 1.5max 4.8±1.3㎜ Tmax Wmax dt P P P ±1.5 < Figure Y > P 9 2 H 1 < Figure F > < Figure J > < Figure A > 3 P0 A F 2 6 8 3 1 4 4 J A 5 6 2 J T 7 3 Code Series Name Code Voltage+Version Code Original Pitch P392 PCMP 392 HA 450V D 10.0mm F 15.0mm Code 4 Capacitance (example) Code 5 Capacitance Tolerance 474 0.47uF J ± 105 1.0uF K ± 10 % 6 Code Revision A Standard 5% 7 Product(Wmax) 12.5 18.0 Code Packing Method Lead Figure Lead length & Height Hole to hole (Po) AM Loose in box - Vinyl A lt= 20.0mm(min.) - 10.0 JT Loose in box - Vinyl J lt=4.5±0.5mm - 10.0 15.0 YT Loose in box - Vinyl Y lt=4.5±0.5mm - 7.5(*) 7.5(*) FG Ammo packing F H0=16.0mm 15.0mm 7.5(*) 7.5(*) *Reduced pitch(Reduced lead spacings). 250 Pitch(P or F) 15.0 Pilkor components PFC Input Capacitors Metallized Polypropylene film capacitors PCMP 392 (MPP) VRdc = 450V CATALOGUE NUMBER Cap. (㎌) Wmax x Hmax x Tmax (mm) Mass loose in box – Vinyl / Figure J (g) C – tol. ± 5% 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 Pitch = 10.0 ± 0.8 mm 12.5 x 10.5 x 5.5 0.7 12.5 x 11.0 x 5.7 0.8 12.5 x 11.5 x 6.2 0.8 12.5 x 12.0 x 6.6 0.9 12.5 x 14.6 x 6.1 1.1 12.5 x 15.2 x 6.7 1.2 12.5 x 15.8 x 7.3 1.4 12.5 x 16.5 x 8.0 1.6 12.5 x 17.3 x 8.8 1.8 Pitch = 15.0 ± 0.8 mm 18.0 x 11.0 x 6.0 0.9 18.0 x 11.5 x 6.0 1.0 18.0 x 12.0 x 6.5 1.1 18.0 x 12.5 x 7.0 1.3 18.0 x 13.0 x 7.7 1.5 18.0 x 13.7 x 8.5 1.8 18.0 x 14.5 x 9.3 2.1 18.0 x 15.5 x 10.0 2.5 18.0 x 16.5 x 11.0 2.9 lt= 4.5 ± 0.5 mm C – tol. ± 10% dt = 0.6 + 0.06 / -0.05 mm P392HAD224JAJT P392HAD274JAJT P392HAD334JAJT P392HAD394JAJT P392HAD474JAJT P392HAD564JAJT P392HAD684JAJT P392HAD824JAJT P392HAD105JAJT dt = 0.8 + 0.08 / -0.05 mm P392HAF474JAJT P392HAF564JAJT P392HAF684JAJT P392HAF824JAJT P392HAF105JAJT P392HAF125JAJT P392HAF155JAJT P392HAF185JAJT P392HAF225JAJT 251 P392HAD224KAJT P392HAD274KAJT P392HAD334KAJT P392HAD394KAJT P392HAD474KAJT P392HAD564KAJT P392HAD684KAJT P392HAD824KAJT P392HAD105KAJT P392HAF474KAJT P392HAF564KAJT P392HAF684KAJT P392HAF824KAJT P392HAF105KAJT P392HAF125KAJT P392HAF155KAJT P392HAF185KAJT P392HAF225KAJT Pilkor components PFC Input Capacitors Metallized Polypropylene film capacitors PCMP 392 (MPP) MOUNTING NORMAL USE The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for mounting on printed-circuit boards by means of automatic insertion machines. SPECIFIC METHOD OF MOUNTING TO WITHSTAND VIBRATIONAND SHOCK . For pitches of 15 mm the capacitors shall be mechanically fixed by the leads . For larger pitches the capacitors shall be mounted in the same way and the body clamped. STORAGE TEMPERATURE . Storage temperature : Tstg = -25 to +40℃ with RH maximum 80% without condensation. RATINGS AND CHARACTERISTICS Unless otherwise specified all electrical values apply at an ambient temperature of 23 ±1℃, an atmospheric pressure of 86 to 106kPa and a relative humidity of 50 ±2%. For reference testing a conditioning period shall be applied OF 116 ±4 hours by heating the products in a circulating air oven at the rated temperature and a relative humidity not exceeding 20%. 252 Pilkor components PFC Input Capacitors Metallized Polypropylene film capacitors PCMP 392 (MPP) CHARACTERISTICS ● Test Voltage . Cut off current 10mA (rise time 100V/sec.) . Test Voltage ( between lead and lead ) : 1.6 x VRdc, 1min. . Test Voltage ( between leads and case ) : 2840 Vdc, 1min. ● Capacitance . Capacitance : Within specified tolerance range when sine wave AC is applied at 1kHz ±200Hz and max. 5Vrms ● Dissipation Factor(DF) . Dissipation factor: When sine wave AC is applied at 10kHz and ≤ 1 Vrms, DF<20X10-4 ● Insulation Resistance . The insulation resistance is measured for 1min.±5s, at 100V for VRdc < 500V, at 500V for VRdc ≥ 500V Rated voltage 450V Minimum RC Minimum Insulation Resistance Capacitance > 0.33uF Capacitance ≤ 0.33uF > 10,000s > 30GΩ ( R = insulation resistance between the terminations[Ω], C= capacitance[Farad] ) ● Rated Voltage Pulse Load Slope(dV/dt)R . For values see specific reference data. IF the pulse voltage is lower than the rated voltage, the values of the specific reference data must be multiplied by VRdc and divided by the applied voltage. Rated voltage 450V MAXIMUM RATED VOLTAGE PULSE SLOPE (V/㎲) P = 10.0 mm P = 15.0 mm 47.5 47.5 253 Pilkor components PFC Input Capacitors Metallized Polypropylene film capacitors PCMP 392 (MPP) THE GRAPHS OF CHARACTERISTICS 10000 10000 564 824 105 155 185 225 224 474 684 1000 1000 Impe dan c e [Ω] Impe danc e [Ω] 105 100 10 100 10 1 1 0.1 0.1 100 1000 10000 100000 100 1000000 1000 10000 100000 Impedance as a function of frequency at Tamb. ≤ 85℃ for original pitch 10.0mm Impedance as a function of frequency at Tamb. ≤ 85℃ for original pitch 15.0mm 10 1000 224 224 474 684 684 105 100 105 AC v ol tage [Vrms] P e rmissi bl e c u rre n t [Arms] 474 1 0.1 10 1 0.01 100 1000 10000 100000 0.1 100 1000000 1000 Fr e qu e n c y [Hz ] 10000 100000 1000000 Fr e qu e n c y [ Hz ] Permissible current as a function of frequency AC voltage as a function of frequency at Tamb. ≤ 85℃ for original pitch 10.0mm at Tamb. ≤ 85℃ for original pitch 10.0mm 1000.0 AC vo l tag e[ V r ms ] 10.0 P e r mi ssi ble c u r re n t [Arms] 1000000 Fr e qu e n c y [Hz ] Fre qu e nc y [Hz ] 1.0 564 824 105 155 185 225 0.1 0.0 100 1000 10000 100000 1000000 Frequency[Hz ] 564 824 105 155 185 225 100.0 10.0 1.0 0.1 100 1000 10000 100000 F r e q u e n c y [H z ] Permissible current as a function of frequency AC voltage as a function of frequency at Tamb. ≤ 85℃ for original pitch 15.0mm at Tamb. ≤ 85℃ for original pitch 15.0mm 254 1000000 Pilkor components PFC Input Capacitors Metallized Polypropylene film capacitors ● PCMP 392 (MPP) Permissible current to temperature When operating in the range of Tamb. (85℃ ~ 105℃) with waveform, the value for characteristic of permissible current to frequency shown in Fig. shall be derated 2.25% at each 1℃. ● Self heating temperature . Maximum allowable rise is 7℃ under 85℃. Maximum permissible continuous voltage vs temperature [℃] Rated voltage derating ratio[%] ● 120 100 80 60 40 20 0 -40 -20 0 20 40 60 80 Temperature[℃] 255 100 120 Pilkor components PFC Input Capacitors Metallized Polypropylene film capacitors PRODUCT MARKING The capacitors are marked on the side in black ink with the following informations : . Rated capacitance in code according to IEC 60062(680nF : 684) . Tolerance on rated capacitance(J : ±5%, K : ±10%) . Rated DC voltage(450V : 450) . Manufacturer's mark(Pilkor ; P) . Manufacturer's type designation(P392) . Code for dielectric material( Metallized polypropylene film : MPP ) . Batch number code(3151100) Example of marking 684 J 450 P392 MPP 3151100 256 PCMP 392 (MPP)