TQG series electronic tilt switches • Omni-directional (horizontal plane) • 2 x trigger angles • PNP or NPN outputs • 0.1A continuous output (max. 250mA 10s) • M12 Male Connector or wire ended • RoHS Compliant Specifications Output dual PNP or NPN (see Fig. 3 for details) Output load Short circuit protection Supply voltage DC 0.1A continuous, 250mA max. 10 sec (resistive) Yes (10s max) DC 8 - 30V Current consumption ≤ 25mA Polarity protection Yes Boot up time <10ms Housing Plastic injection moulded (PBTP) Dimensions (approx.) L x W x H 40 x 40 x 25mm Mounting M3 screws Connection M12 5 pin male connector (others to special order) or wire lead Weight approx. 50g Ambient temperature -25°C to +85°C (storage and operating) Relative humidity Sealing 0 - 95% non-condensing IEC60529 IP67 Shock resistance Measuring range Centering function Frequency response max. 10g detection angles 2 x omni-directional switch points factory programmable pre-centered at 0°, range ±5° (-3dB) 0 - 0.5Hz Accuracy ±0.4° Offset Error 0° (after zeroing / centering) Resolution 0.09° Temperature coefficient Page 1 of 3 www.aecsensors.com Ref: TQGSeries 091014JHM typical ±0.04°/K Sales Department Tel: (888) 847-6552 Specifications are subject to change without notice. E&OE. TQG series electronic tilt switches Fig. 1 Dimensions and mounting holes 5 M12 5p Male connector 1 2 4 3 Pin 1: Pin 2: Pin 3: Pin 4: Pin 5: +Supply Voltage Output 1 Omni-directional Gnd (0V) Output 2 Omni-directional Factory use (Centering/zero set) - leave unconnected in normal use. All dimensions in millimeters. Not to scale. Ordering codes Type T Q 1st Trigger Angle 2nd Trigger Angle G - L C D - - Axis L Cable length / connector - Horizontal Output type NIL - M12 5 Pin male *** - cable length in mm e.g. 500 = 500mm C - 2 x PNP D - 2 x NPN Supply voltage D - 8 - 30VDC 1st trigger angle *** - ±° 2nd trigger angle *** - ±° e.g. 015 = ±15° Page 2 of 3 www.aecsensors.com Ref: TQG Series 091014HM Sales Department Tel: (888) 847-6552 Specifications are subject to change without notice. E&OE. TQG series electronic tilt switches Mounting Orientation Fig. 2 The default 0 ° position is when the switch is mounted horizontally and no acceleration (or tilt) is applied. When mounting, please ensure sufficient space is left to allow for the cable (when selected) or the M12 connector. Undue stress on the cable and connector should be avoided. Output Function Fig. 3 PNP Output: - at 0° ; safe area, outputs 1 & 2: conducting. PNP out (Vsupply) (with external pull-down resistor) - at trigger 1 angle; alert area, output 1: non-conducting. V trigger angle 2 - at trigger 1 angle; alert area, output 1: conducting. 0 unsafe area safe area alert area NPN output: - at 0° ; safe area, outputs 1 & 2: non-conducting. alert area unsafe area -at trigger 2 angle; unsafe area, outputs 1 & 2: non-conducting. trigger angle 1 0 -at trigger 2 angle; unsafe area, outputs 1 & 2: conducting. If the switch is unpowered, the outputs are off (non-conducting). Hysteresis: 0.2° Safe > unsafe delay = 500ms. Unsafe > safe delay = 1000ms. Centering (zeroing) should be done within 1 minute after power up. After zeroing, there is an extra 1 minute left to repeat the centering. Connect the centering input to ground for more than 0.5s In normal use, the centering input pin should be left unconnected. This device is not a “safety” device. For full redundancy (ISO13849), two devices should be used in teh application. Page 3 of 3 American Electronic Components Inc., 1101 Lafayette St. Elkhart, IN46516 www.aecsensors.com Sales Department Tel: (888) 847-6552 Ref: TQG series 091014JHM Specifications are subject to change without notice. E&OE.