Description Purpose and application The VISION motion detector detects the movements of people. The sensor is attached to ceilings and is ideal for mounting at great heights and for wide detection areas. The unit is mounted directly in a dry lining box or using the „Mounting Adapter“, optionally available from OSRAM, to ensure that the installation conforms to the CE guidelines. VISION The VISION motion detector can be connected to any control component with a floating input that is designed for permanent contact (switch). Function The motion detector detects motion within a detection area of 360° and switches on the connected luminaires when motion is registered. When motion is no longer registered, the luminaires switch off after an adjustable delay period. Design The sensor is made up of the following components: • Housing (A) A • Connection cable (B): B –– L: phase (black) –– N: neutral conductor (blue) Motion detector Fitting instructions –– Floating switch contact (2x white) • Motion sensor (C) • Button for setting the delay (D) C E Installation • LED (E) D Safety instructions The motion detector must only be installed and put into operation by a qualified electrician. The applicable safety regulations and accident prevention regulations must be observed. WARNING! Exposed, live cables or damaged housing. Danger of electric shock! • Only work on the motion detector when it is de-energised. CAUTION! Destruction of the motion detector and other devices through incorrect mounting! • Adhere to the connection diagram. • Do not exceed the maximum line length. • Do not route sensor lines together with power supply or lamp lines. IX 2009 VISION_ma0911en_we1.01.indd OSRAM GmbH Kunden Service Center Customer-Service-Center (CSC) Steinerne Furt 62 86167 Augsburg Germany Tel : +49 (0) 1803 677 - 200 (kostenpflichtig / charges apply) Fax.: +49 (0) 1803 677 - 202 www.osram.com www.osram.de 40083219570470 4008321957047 Page 1 of 3 Selecting the installation location Fitting (cont.) FMaximum mounting height: 4,5 m (à detection area Ø 21 m) F 0m 1,5 m 3m 4,5 m 10 m 8m 6m 4m 2m 0 2m 4m 6m 8m 10 m max. 4,5 m max. Ø 21 m GPlace devices that radiate heat outside of the monitoring cone. H Avoid drafts (e.g. from ventilators) G H Attaching the motion detector to the ceiling Note: The mounting adapter, available as an accessory, can be used for attachment. Follow the separate fitting instructions. Unlock and remove the plastic cover by turning it anticlockwise. Screw on the motion detector, using the mounting adapter as an aid, if necessary. Connect the sensor; see the connection diagram. Adjust the delay, if necessary; see the separate operating instructions. Replace the plastic cover and lock it by turning it clockwise. Page 2 of 3 J Fitting (cont.) L N PE Connection diagram 16A J J Variant 1: switching of mains voltage L N PE K Switch contact L Load (ECG, lamps, etc.) K N L 16A L N PE L K N L L N PE L M MVariant 2: floating switching (example with EASY PB Coupler) L N PE K Switch contact N EASY PB Coupler N O EASY control line P EASY control unit T1…8 M L N PE GND K N L O N T1…8 GND P O K N L P Appendix Technical data Operating voltage 120 V … 277 V AC / 50-60 Hz Fuse External 16 A Switch output Floating switch contact Switch output load capacity Max. 5 A – 230 V Inductive load: 250 VA Ohmic lamp: 1200 W Max. number of ECGs: QTP5: 10 pcs. 1x14-35 8 pcs. 1x54 / 2x14-35 6 pcs. 2x80 / 2x54 QTP8: 10 pcs. 1x58 6 pcs. 2x58 QT-FIT8:10 pcs. 1x58 / 1x36 6 pcs. 2x58 / 2x36 QTi: 15 pcs. 1x28/54 10 pcs. 2x28/54 6 pcs. 2x35/49/80 Operating temperature -10 °C … +70 °C Protection type IP 20 Dimensions (Ø x H) 115.6 x 39.9 mm Dimensioned drawing Ø 115,6 mm 39,9 mm The EMC requirements to EN 55015 are fulfilled. Conformity with the relevant EU directives is confirmed by the CE symbol. Page 3 of 3