www.osram.com/LED-systems.com LINEARlight Colormix Flex – LF05CA2 Technical Datasheet Benefits Flexible, cuttable & self-adhesive RGB module Optimum color mixing: each LED contains red, green and blue emitters All emitters centered on the board Developed for colourful ambient, mood and decorative lighting. Applications Light boxes / back lighting Edge-coupling of transparent or diffuse materials Path illumination, contour accentuation Ambient, mood and decorative lighting 8 100 4,000 20 2.2 all dimensions in mm Quick reference Product Order Code Color LF05CA2-RGB3 4008321851536 RGB Dominant Wavelength Red 625 Green Blue 525 465 W/m lm/m lm/W Shipping Units 18 470 26 1/8 7.2 5.4 4.8 161 256 53 22 47 11 Technical features Dimming / Color control Pulse width modulation (PWM) RGB Each LED with 3 separate emitters for RED, GREEN, BLUE All emitters centered on the board Lifetime 50,000 h (L70B50 @ Tc = 40°C) Adhesive tape on backside 3M VHB 9460 Cut & Connect Cuttable every 10 cm / Easy connect with SLIMCONNECTsystem Complementary systems SLIMCONNECTsystem, SLIM TRACK, OPTOTRONIC Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. Subject to change without notice. Errors and omissions excepted. Version: 2013-07-09 LINEARlight Colormix Flex® – LF05CA2 1/4 www.osram.com/LED-systems.com Technical operating data (for overall module) Product Order Code LF05CA2-RGB3 4008321851536 Color RGB Red Green Blue Voltage [V] 24 24 24 24 Power [W] 72 28.8 22 19.2 Current [A] 3 1.2 0.9 0.8 Luminous Flux [lm] 1883 645 1025 213 Radiance Angle [°] 120 Overall Length 4m Minimum & maximum ratings LF05CA2 Operating temperature at Tc-Point [°C] -30 … +75°C Storage temperature [°C] -40 … +85°C Voltage range [V dc] 23 … 25 V Reverse Voltage [V dc] 25 V ► Exceeding maximum ratings for operating and storage temperature will reduce expected life time or destroy the LED Module. ► Exceeding maximum ratings for operating voltage will cause hazardous overload and will likely destroy the LED Module. ► The temperature of the LED module must be measured at the Tc-point according to EN60598-1 in a thermally constant status with a temperature sensor or a temperature sensitive label. For exact location of the Tc-point see drawing below. Technical drawing Safety information ► The module has to be protected from mechanical loads ► Assembly must not damage or destroy conducting paths on the circuit board. ► Installation of LED modules (with power supplies) needs to be made with regard to all applicable and safety standards. Only qualified personnel should be allowed to perform installations. ► Observe correct polarity! Depending on the product incorrect polarity will lead to emission of no light. The module can be damaged after a few seconds. To prevent this, correct polarity immediately! (see "reverse voltage", page 2) ► Parallel connection is highly recommended as safe electrical operation mode. Serial connection is not recommended. Unbalanced voltage drop can cause hazardous overload the LED module. ► ESD protection methods have to be observed when cutting and connecting the module. Check on ESD handling in the application note ESD protection for LED modules. ► The LED Module must not be operated under water ► Please ensure that the power supply is of adequate power to operate the total load. ► When mounting on metallic or otherwise conductive surfaces, there needs to be an electrical isolation at soldering points between module and the mounting surface. ► The maximum run length from any power feed should be limited to 4000 mm. ► Damage by corrosion will not be honored as a materials defect claim. It is the user´s responsibility to provide suitable protection against corrosive agents such as moisture and condensation and other harmful elements. ► For applications involving exposure to humidity and dust the module must be protected by a fixture or housing with a suitable protection class. The module can be protected against condensation water by treatment with an appropriate circuit board grade conformal coating. The conformal coating should have the following features: Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. Subject to change without notice. Errors and omissions excepted. Version: 2013-07-09 LINEARlight Colormix Flex® – LF05CA2 2/4 www.osram.com/LED-systems.com - Optical transparency - UV-resistance - Thermal expansion coefficient 15 – 30 * 10-6 K-1 - low permeability of steam for all climatic conditions - resistance against corrosive environment ► Dimming/ color controlling is only possible with PWM. ► The LINEARlight Colormix Flex is driven ideally by OSRAM OPTORONIC power supplies and control gear. Control gear is available with 1..10V, DALI or DMX interface. ► Please refer to the maximum currents of the control gear when calculating the whole installation (OT DIM: 5A, OTi DALI DIM: 5A, OT DMX, 3-Channel DIM or Sequencer: 2A per channel). Please read our OPTOTRONIC technical installation guide for more detailed information about calculation and wiring diagrams. In order to drive OSRAM LED-Modules safely, it is absolutely necessary to operate them with an electronically stabilized power supply protecting against short circuits, overload and overheating. To also ease the luminaire/installation approval, electronic control gear for LED or LED modules should carry the CE mark and be ENEC certified. In Europe the declarations of conformity must include the following standards: CE: EC 61347-2-13, EN 55015, IEC 61547 and IEC 61000-3-2 - ENEC: 61347-2-13 and IEC/EN 62384. Also check for the mark of an independent authorized certification institute. Please see the relevant brochure for more detailed information (see "Related and Further Information") OSRAM OPTOTRONIC® control gear complies to all relevant standards and guarantees safe operation. Assembly Information ► The module can be connected easily and without any tools with the optional SLIMCONNECTsystem. Please note the maximum ampacity. ► Connection with soldering wires on unmounted module: Do not pretin the solderpads (marked "24V +/RGB")but pretin the wires and solder for max 4 s at 300 °C. Allow solderpoints to completely cool down before the next soldering. Prevent shear- or peel forces. ► Soldering of wires with the module mounted on a heatsink: Pretin solderpads and wires and solder for max 3 s at 350 °C. Allow solderpoints to completely cool down before the next soldering. Prevent shear- or peel forces. ► The mounting of the module is facilitated by means of the double-sided adhesive on the back-surface of the module. Care must be taken to provide a clean and dry mounting surface, free of oils or silicone coatings as well as dirt particle. The mounting substrate must have sufficient structural integrity. Take care to completely remove the protective film. Once the module is appropriately positioned, press on the module with about 20N/cm² (refer to application techniques of 3M adhesive transfer tapes). ► The minimum bending radius is 20 mm. ► When installing in environments with large variations in temperature (e.g. outdoor applications) and operating length of more than 2 m, the use of metallic mounting surfaces is necessary. Otherwise it is advisable to use an additional thicker adhesive tape to absorb the stress of any mismatch in expansion coefficients. ► We do not recommend the use of LINEARlight Colormix Flex® in applications where only white light is needed. For those, rather use LINEARlight POWER Flex®, LINEARlight Flex® ADVANCED & LINEARlight Flex® Eco. Complementary systems and accessories Accessories Type SLIMMCONNECTsystem 4pin Feeder Jumper (board-to-board) Extension wire 30mm Extension wire 150mm SLIM TRACK System SLIM TRACK Mounting Bracket for SLIM TRACK Clear SLIM TRACK Cover Diffuse SLIM TRACK Cover Endcap for Diffuse Cover Semi-Diffuse SLIM TRACK Cover Product EAN Shipping units LF-4PIN Flex SC LF-CONN Flex SC LF-WIRE-30 FLEX SC LF-WIRE-150 FLEX SC 4052899904835 4008321832467 4008321875587 4008321875563 10 / 250 25 / 250 100 / 10,000 50 / 5,000 LF-LTS-2100 SLIM TRACK LF-LTS-MB LF-LTS COVER C LF-LTS-COVER-DIFFUSE LF-LTS-ENDCAP LF-LTS COVER S 4008321978981 4008321979025 4008321790187 4008321979001 4008321979049 4008321790200 40 35 / 280 40 40 20 / 160 40 Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. Subject to change without notice. Errors and omissions excepted. Version: 2013-07-09 LINEARlight Colormix Flex® – LF05CA2 3/4 www.osram.com/LED-systems.com OPTOTRONIC ► Please consider that lengths may differ if further controls are installed. Recommended OPTOTRONIC® drivers Non-dimmable EAN Recommended max. length per driver OPTOTRONIC OT 6/200-240/24 CE OPTOTRONIC OT 8/200-240/24 OPTOTRONIC OT 20/220-240/24 OPTOTRONIC OT 20/120-240/24 S OPTOTRONIC OT 75/220-240/24 OPTOTRONIC OT 75/220-240/24 E OPTOTRONIC OT 80/220-240/24 P OPTOTRONIC OT 120/220-240/24 P OPTOTRONIC OT 240/220-240/24 P Dimmable OPTOTRONIC OT EASY 60 II OPTOTRONIC OT EASY 80 [RECOMMENDATION] 4008321113269 4008321040169 4050300618111 4050300662626 4050300817477 4008321362476 4008321981684 4008321981707 4008321981721 0,1 m ⁽*⁾ - 0,3 m 0 m - 0,4 m 0,1 m ⁽*⁾ - 1,1 m 0,1 m ⁽*⁾ - 1,1 m 0 m - 4,1 m ⁽**⁾ 0 m - 4,1 m ⁽**⁾ 1,4 m ⁽*⁾ - 4,4 m ⁽**⁾ 3,4 m ⁽*⁾ - 6,6 m ⁽**⁾ 6,7 m ⁽*⁾ ⁽**⁾ - 13,3 m ⁽**⁾ 4008321187796 4008321808363 0 m - 3,3 m 0 m - 4,4 m ⁽**⁾ OPTOTRONIC OT 65/220-240/24 3DIM E OPTOTRONIC OTi DALI 75/220-240/24 1-4 CH OPTOTRONIC OT 80/220-240/24 DIM P OPTOTRONIC OT 120/220-240/24 DIM P OPTOTRONIC OT 240/220-240/24 DIM P 4008321964403 4008321371560 4008321981677 4008321981691 4008321981714 0 m - 3,6 m 0 m - 4,1 m ⁽**⁾ 1,4 m ⁽*⁾ - 4,4 m ⁽**⁾ 3,4 m ⁽*⁾ - 6,6 m ⁽**⁾ 6,7 m ⁽*⁾ ⁽**⁾ - 13,3 m ⁽**⁾ ⁽*⁾ Operation with shorter length possible. Recommended minimum length to achieve optimum operating conditions. ⁽**⁾ Total lengths per driver. Length of single strip must not exceed 4 m. Maximim length per OT: lA + lB + lC + … lmax/OT lA Maximum length per strip: lB lA lB lC l… OT – 24V lC ≤ ≤ ≤ ≤ 4m 4m 4m 4m Contacts & information German engineering meets Italian elegance – creating a European product All LINEARlight Colormix Flex® are Made in Italy by OSRAM, with over 100 years of experience in light solutions. OSRAM GmbH Hellabrunner Str. 1 81536 Munich, Germany www.osram.com +49.89.6213-0 (Headquarter) +49.89.6213-6000 (Customer-Service-Center) Sales and technical support is given by the local OSRAM subsidiaries. On the OSRAM website all subsidiaries are listed with complete address and phone numbers. OSRAM LED Systems OSRAM catalogue General information www.osram.com/led-systems http://catalog.osram.com www.osram.com Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. Subject to change without notice. Errors and omissions excepted. Version: 2013-07-09 LINEARlight Colormix Flex® – LF05CA2 4/4