www.osram.com/flex LINEARlight Flex ADVANCED – LF05A2 (Monochrome Versions) Technical Datasheet Benefits Flexible LED strip Adjust the length: cuttable after every 10 cm Applications Note: Picture doesn’t show yet final appearance of the product. Decorative applications Signage Orientation lighting 8 100 20 mm 10,000 2.4 Quick reference Product Order Code Color LF05A2-B3 LF05A2-R3 LF05A2-T3 LF05A2-Y3 LF05A2-O3 4052899924123 4052899924086 4052899924116 4052899924109 4052899924093 BLUE RED GREEN YELLOW ORANGE Dominant Wavelength 467 625 525 587 602 W/m lm/m LED/m 7,2 8,3 4,9 8,3 8,3 851 / 802 2301 / 1202 2001 / 1802 2101 / 1102 2301 / 1302 50 50 50 50 50 Shipping Units 8 8 8 8 8 Technical features Dimmable Pulse width modulation (PWM) 3 Lifetime (L70B50 / L60B50 ) 50,000 h Adhesive tape on backside 3M VHB 9460 Complementary systems SLIMCONNECTsystem, SLIM TRACK, OPTOTRONIC 1 Instant on value Steady state value in working conditions 3 For blue and green version 2 Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. Subject to change without notice. Errors and omissions excepted. Version: 2014-06-06 LINEARlight Flex® ADVANCED (Monochrome Versions) 1/5 www.osram.com/flex Technical operating data (for overall module) Product LF05A2-B3 LF05A2-R3 LF05A2-T3 LF05A2-Y3 LF05A2-O3 Order Code 4052899924123 4052899924086 4052899924116 4052899924109 4052899924093 Voltage [V] 24 24 24 24 24 Power [W] 72 83 49 83 83 Current [A] 3,0 3,5 2,0 3,5 3,5 Luminous Flux [lm] 8501 / 7702 23301 / 12102 19901 / 17802 20601 / 10702 23301 / 13102 Radiance Angle [°] 120 120 120 120 120 Overall Length 10 m 10 m 10 m 10 m 10 m Minimum & maximum ratings Operating temperature at Tc-Point Storage temperature Voltage range Reverse Voltage [°C] -20 … +75 [°C] -20 … +80 [V dc] 23 … 25 [V dc] 25 ► Exceeding maximum ratings for operating and storage temperature will reduce expected life time or destroy the LED Module. ► Exceeding maximum ratings for operating voltage will cause hazardous overload and will likely destroy the LED Module. ► The temperature of the LED module must be measured at the Tc-point according to EN60598-1 in a thermally constant status with a temperature sensor or a temperature sensitive label. For exact location of the Tc-point see drawing below. Technical drawings Early cutting marks using TERM (accessory) 1 2 Instant on value Steady state value in working conditions Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. Subject to change without notice. Errors and omissions excepted. Version: 2014-06-06 LINEARlight Flex® ADVANCED (Monochrome Versions) 2/5 www.osram.com/flex Early cutting marks using resistor Note: R package 1206 (0.5W) Safety information ► The LED module itself and all its components must not be mechanically stressed. ► Assembly must not damage or destroy conducting paths on the circuit board. ► Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards. Only qualified personnel should be allowed to perform installations. ► Observe correct polarity! Depending on the product incorrect polarity will lead to emission of red or no light. The module can be destroyed! Correct polarity immediatelly! (see "reverse voltage", page 2). ► Parallel connection is highly recommended as safe electrical operation mode. Serial connection is not recommended. Unbalanced voltage drop can cause hazardous overload and damage the LED module. ► Please ensure that the power supply is of adequate power to operate the total load. ► When mounting on metallic or otherwise conductive surfaces, there needs to be an electrical isolation at soldering points between module and the mounting surface. ► The maximum length of a coherently operable unit is 10 m. ► Pay attention to standard ESD precautions when installing and handling the module. ► The module, as manufactured, has no conformal coating and therefore offers no inherent protection against corrosion. The ability to customize the length of the module by cutting at specifically marked points is a key feature of the product and hence the reason for no factory installed conformal coating. For these reasons, it is recommended that the user completes all module modifications first (cutting wiring) and then apply a conformal coating in the final stages of installation ► Damage by corrosion will not be honored as a materials defect claim. It is the user’s responsibility to provide suitable protection again corrosive agents such as moisture and condensation and other harmful elements. ► For applications involving exposure to humidity and dust the module must be protected by a fixture or housing with a suitable protection class. The module can be protected against condensation water by treatment with an appropriate circuit board grade conformal coating. The conformal coating should have the following features: Optical transparency UV-resistance Thermal expansion matching the thermal expansion of the module Low permeability of steam for all climatic conditions Resistance against corrosive environment. In order to drive OSRAM LED-Modules safely, it is absolutely necessary to operate them with an electronically stabilized power supply protecting against short circuits, overload and overheating. To also ease the luminaire/installation approval, electronic control gear for LED or LED modules should carry the CE mark and be ENEC certified. In Europe the declarations of conformity must include the following standards: CE: EC 61347-2-13, EN 55015, IEC 61547 and IEC 61000-3-2 - ENEC: 61347-2-13 and IEC/EN 62384. Also check for the mark of an independent authorized certification institute. Please see the relevant brochure for more detailed information (see "Related and Further Information") OSRAM OPTOTRONIC® control gear complies to all relevant standards and guarantees safe operation. Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. Subject to change without notice. Errors and omissions excepted. Version: 2014-06-06 LINEARlight Flex® ADVANCED (Monochrome Versions) 3/5 www.osram.com/flex Assembly Information ► Connection with soldering wires on unmounted module: Do not pretin the solderpads but pretin the wires and solder for max 4 s at 300°C. Allow solderpoints to completely cool down before the next soldering. Prevent shear- or peel forces. ► Soldering of wires with the module mounted on a heatsink: Pretin solderpads and wires and solder for max 3 s at 350 °C. Allow solderpoints to completely cool down before the next soldering. Prevent shear- or peel forces. ► The smallest unit (100 mm- 5 LEDs) can be removed by cutting with scissors between the designated solder pads. ► Mounting of the module is facilitated by the double-sided adhesive tape on the back-surface of the module. ► Mounting surface must be clean and dry, free of oils or silicone coatings as well as dirt particle. ► The mounting substrate must have sufficient structural integrity. Take care to completely remove the protective backing. Once the module is appropriately positioned, pre on the module with about 20N/cm² (refer to application techniques of 3M adhesive transfer tapes). In difficult cases the use of a prime may help. ► The minimum bending radius is 2 cm. The module may be bent over a smaller radius but only in regions of the circuit board containing electronic components and such bends should be made once and fixed in position to avoid cyclic fatigue. ► When installing in environments with large variations in temperature (e.g. outdoor applications) and operating length of more than 2 m, the use of adequate mounting surfaces is necessary . Otherwise it is advisable to use an additional thicker adhesive tape to absorb the stress of any mismatch in expansion. ► LED modules emitting monochromatic light other than white are not intended to serve as general and household illumination, where white emitting light sources are needed: Complementary systems and accessories Accessories Type Product EAN Shipping units SLIMMCONNECTsystem 2pin Feeder Jumper (board-to-board) Extension wire 30mm Extension wire 150mm LF-2PIN Flex SC LF-CONN Flex SC LF-WIRE-30 FLEX SC LF-WIRE-150 FLEX SC 4008321832436 4008321832467 4008321875587 4008321875563 10 / 250 25 / 250 100 / 10,000 50 / 5,000 CONNECTsystem Early cutting Terminator LF-2TERM FLEX 4008321955357 10 / 200 SLIM TRACK System SLIM TRACK Mounting Bracket for SLIM TRACK Clear SLIM TRACK Cover Diffuse SLIM TRACK Cover Endcap for Diffuse Cover Semi-Diffuse SLIM TRACK Cover LF-LTS-2100 SLIM TRACK LF-LTS-MB LF-LTS COVER C LF-LTS-COVER-DIFFUSE LF-LTS-ENDCAP LF-LTS COVER S 4008321978981 4008321979025 4008321790187 4008321979001 4008321979049 4008321790200 40 35 / 280 40 40 20 / 160 40 Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. Subject to change without notice. Errors and omissions excepted. Version: 2014-06-06 LINEARlight Flex® ADVANCED (Monochrome Versions) 4/5 www.osram.com/flex OPTOTRONIC & recommended max. lengths per power supply ► Please consider that lengths may differ if further controls are installed. EAN LF05A-R3 LF05A-O3 LF05A-Y3 LF05A-T3 LF05A-B3 Non-dimmable OPTOTRONIC OT 6/200-240/24 CE OPTOTRONIC OT 8/200-240/24 OPTOTRONIC OT 20/220-240/24 OPTOTRONIC OT 20/120-240/24 S OPTOTRONIC OT 30/220-240/24 P OPTOTRONIC OT 50/220-240/24 OPTOTRONIC OT 75/220-240/24 OPTOTRONIC OT 75/220-240/24 E OPTOTRONIC OT 80/220-240/24 P OPTOTRONIC OT 120/220-240/24 P OPTOTRONIC OT 240/220-240/24 P 4008321113269 4008321040169 4050300618111 4050300662626 4052899043497 4052899905566 4050300817477 4008321362476 4008321981684 4008321981707 4008321981721 max. 0,7 m max. 0,9 m max. 2,4 m max. 2,4 m max. 3,6 m max. 6 m max. 9 m max. 9 m 3,1 m ⁽*⁾ - 9,6 m 7,3 m ⁽*⁾ - 14,4 m ⁽**⁾ 14,5 m ⁽*⁾ ⁽**⁾ - 28,9 m ⁽**⁾ max. 1,2 m max. 1,6 m max. 4 m max. 4 m max. 6,1 m max. 10,2 m ⁽**⁾ max. 15,3 m ⁽**⁾ max. 15,3 m ⁽**⁾ 5,2 m ⁽*⁾ - 16,3 m ⁽**⁾ 12,3 m ⁽*⁾ ⁽**⁾ - 24,4 m ⁽**⁾ 24,5 m ⁽*⁾ ⁽**⁾ - 48,9 m ⁽**⁾ max. 0,8 m max. 1,1 m max. 2,7 m max. 2,7 m max. 4,1 m max. 6,9 m max. 10,4 m ⁽**⁾ max. 10,4 m ⁽**⁾ 3,5 m ⁽*⁾ - 11,1 m ⁽**⁾ 8,4 m ⁽*⁾ - 16,6 m ⁽**⁾ Dimmable OPTOTRONIC OT EASY 60 II OPTOTRONIC OT EASY 80 OPTOTRONIC OT 65/220-240/24 3DIM E OPTOTRONIC OTi DALI 75/220-240/24 1-4 CH OPTOTRONIC OT 80/220-240/24 DIM P OPTOTRONIC OT 120/220-240/24 DIM P OPTOTRONIC OT 240/220-240/24 DIM P 4008321187796 4008321808363 4008321964403 4008321371560 4008321981677 4008321981691 4008321981714 max. 7,2 m max. 9,6 m max. 7,8 m max. 9 m 3,1 m ⁽*⁾ - 9,6 m 7,3 m ⁽*⁾ - 14,4 m ⁽**⁾ 14,5 m ⁽*⁾ ⁽**⁾ - 28,9 m ⁽**⁾ max. 12,2 m ⁽**⁾ max. 16,3 m ⁽**⁾ max. 13,2 m ⁽**⁾ max. 15,3 m ⁽**⁾ 5,2 m ⁽*⁾ - 16,3 m ⁽**⁾ 12,3 m ⁽*⁾ ⁽**⁾ - 24,4 m ⁽**⁾ 24,5 m ⁽*⁾ ⁽**⁾ - 48,9 m ⁽**⁾ Recommended OPTOTRONIC® drivers 16,7 m ⁽*⁾ ⁽**⁾ - 33,3 m ⁽**⁾ max. 8,3 m max. 11,1 m ⁽**⁾ max. 9 m max. 10,4 m ⁽**⁾ 3,5 m ⁽*⁾ - 11,1 m ⁽**⁾ 8,4 m ⁽*⁾ - 16,6 m ⁽**⁾ 16,7 m ⁽*⁾ ⁽**⁾ - 33,3 m ⁽**⁾ ⁽*⁾ Operation with shorter length possible. Recommended minimum length to achieve optimum operating conditions. ⁽**⁾ Total lengths per driver. Length of single strip must not exceed 10 m. Maximim length per OT: lA + lB + lC + … lmax/OT lA Maximum length per strip: lB lA lB lC l… OT – 24V lC ≤ ≤ ≤ ≤ 10 m 10 m 10 m 10 m Contacts & information German engineering meets Italian elegance – creating a European product All LINEARlight Flex® ADVANCED are Made in Italy by OSRAM, with over 100 years of experience in light solutions. OSRAM GmbH Hellabrunner Str. 1 81536 Munich, Germany www.osram.com +49.89.6213-0 (Headquarter) +49.89.6213-6000 (Customer-Service-Center) Sales and technical support is given by the local OSRAM subsidiaries. On the OSRAM website all subsidiaries are listed with complete address and phone numbers. OSRAM LED Systems OSRAM catalogue General information www.osram.com/led-systems http://catalog.osram.com www.osram.com Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. Subject to change without notice. Errors and omissions excepted. Version: 2014-06-06 LINEARlight Flex® ADVANCED (Monochrome Versions) 5/5