E M C C o m p o n e n t s September 2015 3-terminal Filters For signal line MEM Series MEM2012SC Type MEM2012SC 2012[0805 inch]* * Dimensions Code JIS[EIA] (2/7) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20150908 / 3tf_commercial_signal_mem2012sc_en.fm (3/7) E M C C o m p o n e n t s 3-terminal Filters Product compatible with RoHS directive Halogen-free Compatible with lead-free solders For signal line Overview of MEM2012SC Type FEATURES Multilayer chip EMC filter. Monolithic structure makes it highly reliable. Closed magnetic circuit structure makes it possible to achieve high-density mounting without crosstalk. Has sharp attenuation characteristics with excellent EMC suppression. Wide range of products compatible with passing frequencies and attenuating frequencies. T-type circuit is used. Compatible with 1A current. APPLICATION Noise removal from signal lines of data terminals, digital cameras, computers, game machines, flat TVs, etc. PART NUMBER CONSTRUCTION MEM Series name 2012 SC 100 L×W×T Dimensions (mm) 2012 2.0×1.25×0.8 Product internal code SC Capacitance (pF) at 1MHz 100 10 101 100 T T 001 Packaging style Internal code Taping OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Operating Storage temperature temperature (°C) (°C) MEM2012SC –40 to +85 –40 to +85 The Storage temperature range is for after the circuit board is mounted. Package quantity Individual weight (pieces/reel) 4,000 (mg) 8 Type RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150908 / 3tf_commercial_signal_mem2012sc_en.fm (4/7) E M C C o m p o n e n t s MEM2012SC Type RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150°C 180°C Time t1 60 to 120s Soldering Temp. Time T3 t2 230°C 30 to 60s Peak Temp. T4 250 to 260°C Time t3 10s max. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150908 / 3tf_commercial_signal_mem2012sc_en.fm (5/7) E M C C o m p o n e n t s MEM2012SC Type SHAPE & DIMENSIONS 2±0.2 GND 5 NC 4 1 IN/OUT 2 GND 3 OUT/IN 0.1min. 1.25±0.2 NC 6 0.2min. 0.8+0.15, –0.2 0.2min. 0.4±0.15 0.4±0.15 0.4±0.15 Dimensions in mm CIRCUIT DIAGRAM 0.5 2.2 RECOMMENDED LAND PATTERN GND 0.4 1.2 2.6 Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150908 / 3tf_commercial_signal_mem2012sc_en.fm (6/7) E M C C o m p o n e n t s MEM2012SC Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Capacitance Rated voltage (%) ±30 ±30 ±30 ±30 ±30 (pF) 10 22 47 100 150 Tolerance Rated current (V)max. 12 12 12 12 12 DC resistance Part No. [Terminal No.1 to 3] (: )max. 0.15 0.15 0.15 0.15 0.15 (A)max. 1 1 1 1 1 MEM2012SC100T001 MEM2012SC220T001 MEM2012SC470T001 MEM2012SC101T001 MEM2012SC151T001 Measuring frequency: 1(MHz), measuring voltage: 1(V) ○ Measurement equipment Measurement item Product No. Capacitance 4294A Frequency characteristics N5230C * Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies INSERTION LOSS VS. FREQUENCY CHARACTERISTICS 0 Insertion loss (dB) 10 SC151 20 SC101 SC100 SC220 SC470 30 40 50 60 1 10 100 Frequency (MHz) 1000 10000 ○ Measurement equipment Product No. Manufacturer N5230C Agilent Technologies * Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150908 / 3tf_commercial_signal_mem2012sc_en.fm (7/7) E M C C o m p o n e n t s MEM2012SC Type PACKAGING STYLE REEL DIMENSIONS ø60min. 2.0±0.5 1.0 8.4 +2.0 –0.0 ø13±0.2 ø21±0.8 14.4max. ø180±2.0 Dimensions in mm B 3.5±0.05 4.0±0.1 8.0±0.3 2.0±0.05 1.5 +0.1 0 1.75±0.1 TAPE DIMENSIONS K 4.0±0.1 A Dimensions in mm Type MEM2012SC A 1.55±0.20 160min. Drawing direction Taping B 2.30±0.20 K 1.10max. 200min. 300min. Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150908 / 3tf_commercial_signal_mem2012sc_en.fm