TCE0806S Type - Products of TDK

E M C
C o m p o n e n t s
February 2015
Common Mode Filters
With built-in ESD protection element type
TCE Series
TCE0806S Type
TCE0806S
[0302 inch]*
* Dimensions Code JIS[EIA]
(2/8)
E M C
C o m p o n e n t s
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 6 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 20 to 70% RH or
less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
20150203 / cmf_commercial_signal_tce0806s_en.fm
(3/8)
E M C
C o m p o n e n t s
Common Mode Filters
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
With built-in ESD protection element type
Overview of TCE0806S Type
FEATURES
EMC component with an ESD protective device (ESD suppressor) added to a conventional thin-film common mode filter based on the
thin-film processing techniques and material technology cultivated from HDD head manufacturing.
One component can be used both as a common mode noise countermeasure and for ESD protection.
The number of parts and mounting area were greatly reduced.
APPLICATION
Noise countermeasure and ESD protection for high-speed differential interfaces (USB2.0, MIPI, HDMI) for mobile devices and general
consumer products such as smart phones, tablets, digital cameras, and portable music players.
PART NUMBER CONSTRUCTION
TCE
0806
S
Series
name
L×W×T Dimensions
(mm)
0806 0.85×0.65×0.40
Product internal
code
D
-
120
-
Impedance
(:) at 100MHz
120
12
350
35
500
50
2P
-
Number of lines
2P
2 lines
T
□□□
Packaging style
Internal
code
T
Taping
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature range
Operating
Storage
temperature
temperature
(°C)
(°C)
TCE0806S
–25 to +85
–25 to +85
The Storage temperature range is for after the circuit board is mounted.
Package quantity
Individual weight
(pieces/reel)
10,000
(mg)
1.1
Type
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150203 / cmf_commercial_signal_tce0806s_en.fm
(4/8)
E M C
C o m p o n e n t s
TCE0806S Type
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T: Temperature
T4
T3
T2
T3
t3
T1
t1
t2
t: Time
Preheating
Temp.
T1
T2
150°C
180°C
Time
t1
60 to 120s
Soldering
Temp.
Time
T3
t2
230°C
10 to 30s
Peak
Temp.
T4
245°C
Time
t3
5s max.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150203 / cmf_commercial_signal_tce0806s_en.fm
(5/8)
E M C
C o m p o n e n t s
TCE0806S Type
SHAPE & DIMENSIONS
0.65±0.05
5
4
2
6
3
0.40±0.05
0.10typ.
0.85±0.05
1
0.20±0.05
0.15±0.05
0.1
5ty
0.12 +0.08
–0.04
p.
0.12 +0.08
–0.04
0.50±0.05
GND
GND
Dimensions in mm
RECOMMENDED LAND PATTERN
CIRCUIT DIAGRAM
0.15
5
0.
4
2
3
0.30
0.61
1.10
15
1
0.20
6
• No polarity
0.39
0.90
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150203 / cmf_commercial_signal_tce0806s_en.fm
(6/8)
E M C
C o m p o n e n t s
TCE0806S Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Common mode
impedance
DC resistance
[at 100MHz]
(: )
Tolerance
12
±7:
35
±12:
50
±15:
[1 line]
(: )max.
1.0
1.8
2.5
Cutoff
frequency
Clamp voltage Rated current
Rated voltage
Insulation
resistance
(GHz)typ.
8.0
7.0
6.5
(V)max.
100
100
100
(V)max.
10
10
10
(M: )min.
1
1
1
○ Measurement equipment
Measurement item
Product No.
Common mode impedance
4291A
DC resistance
4338A
Insulation resistance
4339A
* Equivalent measurement equipment may be used.
(A)max.
0.1
0.1
0.1
Part No.
TCE0806S-120-2P-T□□□
TCE0806S-350-2P-T□□□
TCE0806S-500-2P-T□□□
Manufacturer
Agilent Technologies
Agilent Technologies
Agilent Technologies
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150203 / cmf_commercial_signal_tce0806s_en.fm
(7/8)
E M C
C o m p o n e n t s
TCE0806S Type
ELECTRICAL CHARACTERISTICS
IMPEDANCE VS. FREQUENCY CHARACTERISTICS
10000
Impedance (Ω)
1000
500 Common mode
350 Common mode
100
120 Common mode
500 Differential mode
10
350 Differential mode
120 Differential mode
1
1
10
100
Frequency (MHz)
1000
10000
○ Measurement equipment
Product No.
Manufacturer
E4991A
Agilent Technologies
* Equivalent measurement equipment may be used.
INSERTION LOSS VS. FREQUENCY CHARACTERISTICS
0
350 Differential mode
120 Differential mode
500 Differential mode
Insertion loss (dB)
5
10
120 Common mode
15
20
500 Common mode
25
1
10
100
Frequency (MHz)
1000
350 Common mode
10000
○ Measurement equipment
Product No.
Manufacturer
E5071B
Agilent Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150203 / cmf_commercial_signal_tce0806s_en.fm
(8/8)
E M C
C o m p o n e n t s
TCE0806S Type
PACKAGING STYLE
REEL DIMENSIONS
ø60 –0
+1
2.0±0.5
1.0
9+0.3
ø13±0.2
ø21±0.8
13+1.4
+0
ø180 –3
Dimensions in mm
B
3.5±0.05
4.0±0.1
A
8.0±0.3
2.0±0.05
1.5 +0.1
0
1.75±0.1
TAPE DIMENSIONS
P1
K
Dimensions in mm
Type
TCE0806S
A
0.74
160min.
Drawing direction
Taping
B
0.94
P1
2.0
K
0.50
200min.
300min.
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150203 / cmf_commercial_signal_tce0806s_en.fm