RFM products are now Murata products. OP4006B1 • • • • • Quartz SAW Stabilized Differential Output Technology Very Low Jitter Fundamental-Mode Operation at 666.51 MHz Voltage Tunable for Phase Locked Loop Applications Optical Timing Reference for Forward Error Correction Applications Complies with Directive 2002/95/EC (RoHS) 2 > 666.51 MHz Optical Timing Clock The OP4006B1 is a voltage-controlled SAW clock (VCSC) designed for phase-locked loop (PLL) applications in optical data communications systems. The differential outputs of the OP4006B1 are generated by high-Q, fundamental mode quartz surface acoustic wave (SAW) technology. This technique provides very low output jitter and phase noise, plus excellent immunity to power supply noise. The OP4006B1 differential outputs feature ±1% symmetry, and can be DC-configured to drive a wide range of high-speed logic families. The OP4006B1 is packaged in a hermetic metal-ceramic LCC. Absolute Maximum Ratings Rating Value Units DC Suppy Voltage 0 to 5.5 Vdc Tuning Voltage 0 to 5.5 Vdc -55 to 100 °C Case Temperature SMC-08A Electrical Characteristics Characteristic Operating Frequency Sym Notes fO 1 666.51 Tuning Range 2 ±100 Tuning Voltage 1 Tuning Linearity 1, 8 Absolute Frequency Minimum VO 3, 4, 5 Harmonic Spurious 3, 4, 6 ±5 V % kHz 0.60 1.1 VP-P 2:1 49 3, 4, 6, 7 51 % -15 dBc -60 dBc @ 100 Hz offset 3, 6 -70 dBc/Hz @ 1 kHz offset 3, 6 -100 dBc/Hz @ 10 kHz offset 3, 6 -125 dBc/Hz Noise Floor 3, 6 -150 dBc/Hz RMS Jitter 3, 4, 6, 7 1 ps No Noise on VCC 3, 4, 6, 7 12 psP-P 12 psP-P 200 mVP-P Noise, from 1 MHz to ½ fO on 3 Output DC Resistance (between Q & Q) DC Power Supply ppm 3.3 1,3 Symmetry Nonharmonic Spurious Q and Q Jitter 1,3 Units MHz 50 Voltage into 50 Ω (VSWR < 1.2) Operating Load VSWR Phase Noise Maximum 0 Modulation Bandwidth Q and Q Output Typical 1, 3 50 3.13 Operating Voltage VCC 1, 3 Operating Current ICC 1, 3 TC 1, 3 Operating Case Temperature KΩ 3.3 or 5.0 -40 5.25 Vdc 70 mA +85 °C RFM OP4006B1 YYWW Lid Symbolization (YY=Year, WW=Week) CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. COCOM CAUTION: Approval by the U.S. Department of Commerce is required prior to export of this device. NOTES: 1. 2. 3. 4. 5. 6. 7. 8. Unless otherwise noted, all specifications include the combined effects of load VSWR, VCC and TC. Net tuning range after tuning out the effects of initial manufacturing tolerances, VSWR pushing/pulling, VCC, TC and aging. The internal design, manufacturing processes, and specifications of this device are subject to change without notice. Specified only for a balanced load with a VSWR < 1.2 ( 50 ohms each side), and a VCC = 3.0 Vdc. Symmetry is defined as the width in (% of total period) measure at 50% of the peak-to-peak voltage of either output. Jitter and other noise outputs due to power supply noise or mechanical vibration are not included in this specification except where noted. Applies to period jitter of either differential output. Measured with a Tektronix CSA803 signal analyzer with at least 1000 samples. One or more of the following United States patents apply: 4, 616,197; 4,670,681; 4,760,352. ©2010-2015 by Murata Electronics N.A., Inc. OP4006B1 (R) 4/1/15 Page 1 of 2 www.murata.com OP Performance Curves and Application Information See the OP4005B Data Sheet for typical OP performance curves and application information. SMC-8A 8-Terminal Surface Mount Case Typical Printed Circuit Board Land Pattern A typical land pattern for a circuit board is shown below. Grounding of the metallic center pad is optional. Typically 0.01" to 0.05" or 0.25 mm to 1.25 mm (8 Places) (The optimum value of this dimension is dependent on the PCB assembly process employed.) Electrical Connections Terminal Number Connection 1 Tune 2 *Enable 3 Ground 4 Ground 5 Q Output 6 Q Output 7 VCC 8 Ground LID Ground Dimensions 8 mm MIN MAX Inches MIN MAX 1 7 A 13.46 13.97 0.530 0.550 B 9.14 9.66 0.360 0.380 2 6 C 1.93 Nominal 0.076 Nominal D 1.93 Nominal 0.076 Nominal 3 5 E 2.54 Nominal 0.100 Nominal F 1.27 Nominal 0.050 Nominal Dimension 4 *Enable Sense: Pin 2 Ground-Clock Off B D C E A F 0.190 X 0.088 CENTERED ©2010-2015 by Murata Electronics N.A., Inc. OP4006B1 (R) 4/1/15 Page 2 of 2 www.murata.com