RFM products are now Murata products. PX10004 • • • • • • Designed for TDMA IS-54 / CDPD IF Applications Low Insertion Loss Excellent Selectivity Hermetic 13.3 X 6.5 mm Surface-Mount Case Unbalanced Input and Output Complies with Directive 2002/95/EC (RoHS) 82.2 MHz SAW Filter Pb Absolute Maximum Ratings Rating Value Units Maximum Incident Power in Passband +10 dBm Max. DC voltage between any 2 terminals 30 VDC Storage Temperature Range -40 to +85 Suitable for lead-free soldering - Max Soldering Profile Electrical Characteristics Characteristic Sym Nominal Center Frequency fC Passband °C 260°C for 30 s Insertion Loss at fc 3 dB Passband Min IL BW3 GDV Typ 3 ±15 1, 2 2.5 fc ±60 kHz 10 fc -880 kHz to fc -940 kHz 1, 2, 3 65 Ultimate 4.0 dB kHz 1.0 dBP-P 6.0 µsP-P -95 dBm 16 68 dB 65 TA Operating Temperature Range Units MHz ±25 Third-Order Intermod. for -20 dBm tones at fc ±60 & 120 kHz Rejection Max 82.200 1 Amplitude Ripple over fc ±15 kHz Group Delay Variation over fc ±10 kHz Notes SM13365-12 1 Impedance Matching to 50 Ω unbalanced +70 -20 °C External L-C Case Style SM13365-12 13.3 X 6.5 mm Nominal Footprint Lid Symbolization (YY=year, WW=week) See note 4 RFM PX1004 YYWW Electrical Connections Connection Terminals Port 1Hot 2 Port 1 Gnd Return 3 Port 2 Hot 8 Port 2 Gnd Return Case Ground 9 All Others Caution: Electrostatic Sensitive Device. Observe precautions for handling. NOTES: 1. 2. 3. 4. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." ©2010-2015 by Murata Electronics N.A., Inc. PX10004 (R) 2/12/15 5. 6. 7. 8. Page 1 of 5 The design, manufacturing process, and specifications of this filter are subject to change. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. Murata, stylized Murata logo, and Murata N.A., Inc. are registered trademarks of Murata Manufacturing Co., Ltd. www.murata.com ©2010-2015 by Murata Electronics N.A., Inc. PX10004 (R) 2/12/15 Page 2 of 5 www.murata.com ©2010-2015 by Murata Electronics N.A., Inc. PX10004 (R) 2/12/15 Page 3 of 5 www.murata.com Tape and Reel Specifications "B" REF. 254 100 REF. Quantity Per Reel 100 Min 1000 Max See Detail "A" 13. 0 12.0 24.4 20 21.0 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao 7.0 mm Bo 13.8 mm Ko 2.0 mm Pitch 12.0 mm W 24.0 mm PIN #1 USER DIRECTION OF FEED ©2010-2015 by Murata Electronics N.A., Inc. PX10004 (R) 2/12/15 Page 4 of 5 www.murata.com SM13365-12 Case 12-Terminal Ceramic Surface-Mount Case 13.3 x 6.5 mm Nominal Footprint Case Dimensions mm Dimension A B C D E H P Inches Min Nom Max Min Nom Max 13.08 6.27 13.31 6.50 1.91 1.50 0.79 1.0 2.54 13.60 6.80 2.00 0.515 0.247 0.524 0.256 0.075 0.059 0.031 0.039 0.100 0.535 0.268 0.079 Materials Solder Pad Termination Au plating 30 - 60 uInches (76.2-152 uM) over 80-200 uInches (203-508 uM) Ni. Lid Fe-Ni-Co Alloy Electroless Nickel Plate (8-11% Phosphorus) 100-200 uInches Thick Body Al2O3 Ceramic 0.077 TYP. (1.96) Pb Free C B D H 2 2 3 4 1 5 1 4 12 12 5 6 11 11 6 7 10 10 7 P (8 Places) 0.334 REF. (8.48) (14.10) 0.555 0.100 TYP. (2.54) 0.034 TYP. (0.86) 3 A 8 9 9 E (10 Places) 8 0.287 (7.29) ©2010-2015 by Murata Electronics N.A., Inc. PX10004 (R) 2/12/15 TOP VIEW Page 5 of 5 BOTTOM VIEW www.murata.com