RFM products are now Murata products. SF2186E • Surface Mount 3.0 x 3.0 mm Package • Complies with Directive 2002/95/EC (RoHS) Pb 1268.52 MHz SAW Filter Absolute Maximum Ratings Rating Value Units 10 dBm Input Power Level 3 V Operating Temperature Range DC Voltage on any Non-ground Terminal -40 to +85 °C Storage Temperature Range in Tape and Reel -40 to +85 °C Suitable for Lead-free Soldering - Maximum Soldering Profile 260°C for 30 s SM3030-6 Electrical Characteristics Characteristic Sym Center Frequency fC Notes Min Typ 1268.52 Insertion Loss, 1258.29 to 1278.75 MHz IL 1.7 3.2 0.5 1.8 Amplitude Ripple, 1258.29 to 1278.75 MHz 2 dB Bandwidth 20.46 38.3 1227.52 MHz 39 45.5 1309.52 MHz 50 67 Max Units MHz dB MHz Attenuation, Referenced from Minimum IL: Input/Output VSWR, 1258.29 to 1278.75 MHz 1.3 Source Impedance ZS 50 Load Impedance ZL 50 Case Style 2.1 SM3030-6 3.0 x 3.0 mm Nominal Footprint Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator Standard Reel Quantity dB 874, YWWS Reel Size 7 Inch 500 Pieces/Reel Reel Size 13 Inch 3000 Pieces/Reel Electrical Connections Connection Terminals Input 2 Output 5 Case Ground 5 0 o h m 2 5 . & $ - 5 5 0 o h m 1 , 3 , 4 , 6 All others CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. NOTES: 1. 2. 3. 4. 5. 6. 7. 8. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 and measured with 50 network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. Murata, stylized Murata logo, and Murata N.A., Inc. are registered trademarks of Murata Manufacturing Co., Ltd. ©2010-2015 by Murata Electronics N.A., Inc. SF2186E (R) 8/3/15 Page 1 of 5 www.murata.com SF2186E Amplitude Response, 100 MHz Sweep SF2186E Amplitude Response, 300 MHz Sweep ©2010-2015 by Murata Electronics N.A., Inc. SF2186E (R) 8/3/15 Page 2 of 5 www.murata.com SF2186E Input VSWR, 100 MHz Sweep SF2186E Output VSWR, 100 MHz Sweep ©2010-2015 by Murata Electronics N.A., Inc. SF2186E (R) 8/3/15 Page 3 of 5 www.murata.com SM3030-6 Case 6-Terminal Ceramic Surface-Mount Case 3.0 X 3.0 mm Nominal Footprint Case and PCB Footprint Dimensions Dimension K L N K N O A B C D E F G H I J K L M N O Min 2.87 2.87 1.12 0.77 2.67 1.47 0.72 1.37 0.47 1.17 mm Nom 3.00 3.00 1.25 0.90 2.80 1.60 0.85 1.50 0.60 1.30 3.20 1.70 1.05 0.81 0.38 Max 3.13 3.13 1.38 1.03 2.93 1.73 0.98 1.63 0.73 1.43 Min 0.113 0.113 0.044 0.030 0.105 0.058 0.028 0.054 0.019 0.046 Inches Nom 0.118 0.118 0.049 0.035 0.110 0.063 0.033 0.059 0.024 0.051 0.126 0.067 0.041 0.032 0.015 Max 0.123 0.123 0.054 0.040 0.115 0.068 0.038 0.064 0.029 0.056 Case Materials Materials N M M PCB Footprint Top View Solder Pad Plating 0.3 to 1.0 μm Gold over 1.27 to 8.89 μm Nickel Lid Plating 2.0 to 3.0 μm Nickel Body Al2O3 Ceramic Pb Free TOP VIEW BOTTOM VIEW 874 YWWS ©2010-2015 by Murata Electronics N.A., Inc. SF2186E (R) 8/3/15 Page 4 of 5 www.murata.com Tape and Reel Specifications “B” Inches Quantity Per Reel millimeters 7 178 500 13 330 3000 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao 3.35 mm Bo 3.35 mm Ko 1.40 mm Pitch 8.0 mm W 12.0 mm PIN #1 679 YWWS USER DIRECTION OF FEED ©2010-2015 by Murata Electronics N.A., Inc. SF2186E (R) 8/3/15 Page 5 of 5 www.murata.com