ZL38001 AEC for Analog Hands-Free Communication Data Sheet Zarlink has introduced a new generation family of AEC (ZL38002 and ZL38004). Zarlink recommends these products for new designs. September 2010 Ordering Information ZL38001QDG1 ZL38001DGF1 Features • • • • • • • • • ST-BUS, GCI, or variable-rate SSI PCM interfaces User gain control provided for speaker path (-24 dB to +48 dB in 3 dB steps) 18 dB gain at Sout to compensate for high ERL environments AGC on speaker path Handles up to 0 dB acoustic echo return loss Transparent data transfer and mute options 20 MHz master clock operation Low power mode during PCM Bypass Bootloadable for future factory software upgrades 2.7 V to 3.6 V supply voltage; 5 V tolerant inputs • • • • • • • • Limiter Sin /A-Law/ + Offset Null Linear - S2 MD1 NBSD 18dB Gain ADV NLP + Linear/ /A-Law S3 S1 Program ROM CONTROL DATA1 Micro Interface DATA2 Howling Adaptive Filter Double Talk Detector Controller NBSD R3 R1 SCLK R2 MD2 -24 -> +21 dB Linear/ /A-Law Rout AGC User Gain CS ADV NLP + Offset Null + /A-Law/ Linear Limiter VDD VSS RESET FORMAT ENA1 ENA2 PORT 1 UNIT Adaptive Filter Sout Program RAM Line ECho Path • • ACOUSTIC ECHO PATH • ZL38001DGE1 Contains two echo cancellers: 112 ms acoustic echo canceller + 16 ms line echo canceller Works with low cost voice codec. ITU-T G.711 or signed mag /A-Law, or linear 2’s comp Each port may operate in different format Advanced NLP design - full duplex speech with no switched loss on audio paths Fast re-convergence time: tracks changing echo environment quickly Adaptation algorithm converges even during Double-Talk Designed for exceptional performance in high background noise environments Provides protection against narrow-band signal divergence Howling prevention stops uncontrolled oscillation in high loop gain conditions Offset nulling of all PCM channels Serial micro-controller interface PORT 2 • 48 Pin TQFP* Trays, Bake & Drypack 36 Pin SSOP* Tape & Reel, Bake & Drypack 36 Pin SSOP* Tubes, Bake & Drypack *Pb Free Matte Tin -40C to +85C LAW F0i BCLK/C4i MCLK Figure 1 - Functional Block Diagram 1 Zarlink Semiconductor Inc. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright 2004-2010, Zarlink Semiconductor Inc. All Rights Reserved. Rin ZL38001 Data Sheet Applications • Hands-free in automobile applications MT93L16 ZL38001 ZL38002 ZL38003 Description AEC for analog handsfree communication AEC for analog hands- AEC with noise reduction for digital free communication hands-free communication AEC with noise reduction & codecs for digital hands-free communication Application Analog Desktop phone Analog Intercom Analog Desktop phone Hands-free Car Kits Hands-free Car Kits Analog Intercom Digital Desktop Phone Home Security Digital Desktop Phone Home Security Intercom & Pedestals Intercom & Pedestals Features AEC 1 channel 1 channel 1 channel 1 channel LEC 1 channel 1 channel Custom Load Custom Load Gains User Gain User Gain/18 dB Gain on Sout User Gain + System tuning gains User Gain + System tuning gains Noise Reduction N N Y Y Integrated Codecs N N N dual channel Table 1 - Acoustic Echo Cancellation Family 2 Zarlink Semiconductor Inc. ZL38001 VSS2 IC IC BCLK/C4i F0i Rout Sout VDD NC DATA1 DATA2 NC MCLK2 IC IC IC NC ENA1 NC MD1 ENA2 MD2 Rin 36 32 34 30 28 26 24 38 22 40 20 42 TQFP 18 44 16 46 14 48 2 4 6 8 10 Sout VDD NC DATA1 NC DATA2 NC CS SCLK NC NC RESETB 12 IC IC IC LAW NC FORMAT NC IC IC IC MCLK2 NC VSS VDD2 MCLK SSOP 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 NC VSS VDD2 VSS2 NC IC IC BCLK/C4i NC F0i Rout NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 NC Sin IC NC ENA1 MD1 ENA2 MD2 Rin Sin IC MCLK IC IC IC LAW FORMAT RESET NC NC SCLK CS Data Sheet Figure 2 - Pin Connections Pin Description SSOP Pin # TQFP Pin # Name Description 1 43 ENA1 SSI Enable Strobe/ST-BUS & GCI Mode for Rin/Sout (Input). This pin has dual functions depending on whether SSI or ST-BUS/GCI is selected. For SSI, this strobe must be present for frame synchronization. This is an active high channel enable strobe, 8 or 16 data bits wide, enabling serial PCM data transfer for on Rin/Sout pins. Strobe period is 125 microseconds. For ST-BUS or GCI, this pin, in conjunction with the MD1 pin, selects the proper mode for Rin/Sout pins (see ST-BUS and GCI Operation description). 2 45 MD1 ST-BUS & GCI Mode for Rin/Sout (Input). When in ST-BUS or GCI operation, this pin, in conjunction with the ENA1 pin, will select the proper mode for Rin/Sout pins (see ST-BUS and GCI Operation description). Connect this pin to Vss in SSI mode. 3 46 ENA2 SSI Enable Strobe /ST-BUS & GCI Mode for Sin/Rout (Input). This pin has dual functions depending on whether SSI or ST-BUS/GCI is selected. For SSI, this is an active high channel enable strobe, 8 or 16 data bits wide, enabling serial PCM data transfer on Sin/Rout pins. Strobe period is 125 microseconds. For ST-BUS/GCI, this pin, in conjunction with the MD2 pin, selects the proper mode for Sin/Rout pins (see ST-BUS and GCI Operation description). 4 47 MD2 ST-BUS & GCI Mode for Sin/Rout (Input). When in ST-BUS or GCI operation, this pin in conjunction with the ENA2 pin, selects the proper mode for Sin/Rout pins (see ST-BUS and GCI Operation description). Connect this pin to Vss in SSI mode. 3 Zarlink Semiconductor Inc. ZL38001 Data Sheet Pin Description (continued) SSOP Pin # TQFP Pin # Name Description 5 48 Rin Receive PCM Signal Input (Input). 128 kbps to 4096 kbps serial PCM input stream. Data may be in either companded or 2’s complement linear format. This is the Receive Input channel from the line (or network) side. Data bits are clocked in following SSI, GCI or ST-BUS timing requirements. 6 2 Sin Send PCM Signal Input (Input). 128 kbps to 4096 kbps serial PCM input stream. Data may be in either companded or 2’s complement linear format. This is the Send Input channel (from the microphone). Data bits are clocked in following SSI, GCI or ST-BUS timing requirements. 7 3 IC Internal Connection (Input). Must be tied to Vss. 8 5 MCLK 9,10,11 6, 7, 8 IC 12 9 LAW 13 11 14 13 RESET 17 16 SCLK 18 17 CS 19 19 DATA2 Serial Data Receive (Input). In Motorola/National serial microport operation, the DATA2 pin is used for receiving data. In Intel serial microport operation, the DATA2 pin is not used and must be tied to Vss or Vdd. 20 21 DATA1 Serial Data Port (Bidirectional). In Motorola/National serial microport operation, the DATA1 pin is used for transmitting data. In Intel serial microport operation, the DATA1 pin is used for transmitting and receiving data. 22 23 VDD Positive Power Supply (Input). Nominally 3.3 volts. 23 24 Sout Send PCM Signal Output (Output). 128 kbps to 4096 kbps serial PCM output stream. Data may be in either companded or 2’s complement linear PCM format. This is the Send Out signal after acoustic echo cancellation and non-linear processing. Data bits are clocked out following SSI, STBUS or GCI timing requirements. 24 26 Rout Receive PCM Signal Output (Output). 128 kbps to 4096 kbps serial PCM output stream. Data may be in either companded or 2’s complement linear PCM format. This is the Receive out signal after line echo cancellation nonlinear processing, AGC and gain control. Data bits are clocked out following SSI, ST-BUS or GCI timing requirements. Master Clock (Input). Nominal 20 MHz Master Clock input (may be asynchronous relative to 8 KHz frame signal.) Tie together with MCLK2 (pin 33). Internal Connection (Input). Must be tied to Vss. A/ Law Select (Input). When low, selects Law companded PCM. When high, selects A-Law companded PCM. This control is for both serial pcm ports. FORMAT ITU-T/Sign Mag (Input). When low, selects sign-magnitude PCM code. When high, selects ITU-T (G.711) PCM code. This control is for both serial pcm ports. Reset / Power-down (Input). An active low resets the device and puts the ZL38001 into a low-power stand-by mode. Serial Port Synchronous Clock (Input). Data clock for the serial microport interface. Serial Port Chip Select (Input). Enables serial microport interface data transfers. Active low. 4 Zarlink Semiconductor Inc. ZL38001 Data Sheet Pin Description (continued) SSOP Pin # TQFP Pin # Name 25 27 F0i 26 29 27, 28 30, 31 IC 29 33 VSS2 Digital Ground (Input). Nominally 0 volts. 30 34 VDD2 Positive Power Supply (Input). Nominally 3.3 volts (tie together with VDD, pin 22). 31 35 VSS 33 38 MCLK2 34,35,36 39, 40, 41 IC Internal Connection (Input). Tie to Vss. 15, 16, 21, 32 1, 4, 10, 12, 14, 15, 18, 20, 22, 25, 28, 32, 36, 37, 42, 44 NC No Connect (Output). This pin should be left unconnected. Description Frame Pulse (Input). In ST-BUS (or GCI) operation, this is an active-low (or active-high) frame alignment pulse, respectively. SSI operation is enabled by connecting this pin to Vss. BCLK/C4i Bit Clock/ST-BUS Clock (Input). In SSI operation, BCLK pin is a 128 kHz to 4.096 MHz bit clock. This clock must be synchronous with ENA1 and ENA2 enable strobes. In ST-BUS or GCI operation, C4i pin must be connected to the 4.096 MHz (C4) system clock. Internal Connection (Input). Tie to Vss. Digital Ground (Input). Nominally 0 volts (tie together with VSS2, pin 29). Master Clock (Input). Nominal 20 MHz master clock (tie together with MCLK, pin 8). 5 Zarlink Semiconductor Inc. ZL38001 Data Sheet Table of Contents 1.0 Changes Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.0 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.1 Adaptation Speed Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.2 Advanced Non-Linear Processor (ADV-NLP)1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.3 Narrow Band Signal Detector (NBSD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.4 Howling Detector (HWLD)1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.5 Offset Null Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.6 Limiters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.7 User Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.8 AGC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.9 18 dB Gain Pad at Sout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.10 Mute Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.11 Bypass Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 2.12 Adaptation Enable/Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 2.13 ZL38001 Throughput Delay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 2.14 Power Down / Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.0 PCM Data I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.1 ST-BUS and GCI Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.2 SSI Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 3.3 PCM Law and Format Control (LAW, FORMAT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3.4 Linear PCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 3.5 Bit Clock (BCLK/C4i) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 3.6 Master Clock (MCLK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 4.0 Microport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 4.1 Bootload Process and Execution from RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 5.0 Register Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 6 Zarlink Semiconductor Inc. ZL38001 Data Sheet List of Figures Figure 1 - Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Figure 2 - Pin Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Figure 3 - ST-BUS and GCI 8-Bit Companded PCM I/O on Timeslot 0 (Mode 1) . . . . . . . . . . . . . . . . . . . . . . . . . 14 Figure 4 - ST-BUS and GCI 8-Bit Companded PCM I/O on Timeslot 2 (Mode 2) . . . . . . . . . . . . . . . . . . . . . . . . . 15 Figure 5 - ST-BUS and GCI 8-Bit Companded PCM I/O with D and C channels (Mode 3) . . . . . . . . . . . . . . . . . . 16 Figure 6 - ST-BUS and GCI 16-Bit 2’s Complement Linear PCM I/O (Mode 4). . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 7 - SSI Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 8 - Serial Microport Timing for Intel Mode 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 9 - Serial Microport Timing for Motorola Mode 00 or National Microwire . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Figure 10 - Master Clock - MCLK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Figure 11 - GCI Data Port Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Figure 12 - ST-BUS Data Port Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Figure 13 - SSI Data Port Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Figure 14 - INTEL Serial Microport Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Figure 15 - Motorola Serial Microport Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 7 Zarlink Semiconductor Inc. ZL38001 Data Sheet List of Tables Table 1 - Acoustic Echo Cancellation Family . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Table 2 - Quiet PCM Code Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Table 3 - ST-BUS & GCI Mode Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Table 4 - SSI Enable Strobe Pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Table 5 - Companded PCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Table 6 - Bootload RAM Control (BRC) Register States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Table 7 - Reference Level Definition for Timing Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 8 Zarlink Semiconductor Inc. ZL38001 Data Sheet List of Register Tables Register Table 1 - Main Control Register (MC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Register Table 2 - Acoustic Echo Canceller Control Register (AEC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Register Table 3 - Line Echo Canceller Control Register (LEC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Register Table 4 - Acoustic Echo Canceller Status Register (ASR) (* Do not write to this register) . . . . . . . . . . . . . . . . . 32 Register Table 5 - Line Echo Canceller Status Register (LSR) (* Do not write to this register) . . . . . . . . . . . . . . . . . . . . . 33 Register Table 6 - Receive Gain Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Register Table 7 - Double Talk Gain Control Register 1 (DTGCR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Register Table 8 - Double Talk Gain Control Register 2 (DTGCR2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Register Table 9 - Double Talk detection Threshold Register (DTDT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Register Table 10 - Receive (Rin) Peak Detect Register 1 (RIPD1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Register Table 11 - Receive (Rin) Peak Detect Register 2 (RIPD2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Register Table 12 - Receive (Rin) ERROR Peak Detect Register 1 (REPD1). . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Register Table 13 - Receive (Rin) ERROR Peak Detect Register 2 (REPD2). . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Register Table 14 - Receive (Rout) Peak Detect Register 1 (ROPD1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Register Table 15 - Receive (Rout) Peak Detect Register 2 (ROPD2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Register Table 16 - Send (Sin) Peak Detect Register 1 (SIPD1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Register Table 17 - Send (Sin) Peak Detect Register 2 (SIPD2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Register Table 18 - Send ERROR Peak Detect Register 1 (SEPD1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Register Table 19 - Send ERROR Peak Detect Register 2 (SEPD2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Register Table 20 - Send (Sout) Peak Detect Register 1 (SOPD1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Register Table 21 - Send (Sout) Peak Detect Register 2 (SOPD2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Register Table 22 - Rout Limiter Register 1 (RL1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Register Table 23 - Rout Limiter Register 2 (RL2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Register Table 24 - Sout Limiter Register (SL). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Register Table 25 - Firmware Revision Code Register (FRC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Register Table 26 - Bootload RAM Control Register (BRC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Register Table 27 - Bootload RAM Signature Register (SIG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 9 Zarlink Semiconductor Inc. ZL38001 1.0 Data Sheet Changes Summary The following table captures the changes from the October 2006 issue. Page Item Change 1 Ordering Information Box Removed the ZL38001QDC and ZL38001DGA packages. 3 “Pin Description“ Table Removed QSOP Pin Descriptions. 3 “Pin Description“ Table Added SSOP Pin Descriptions. 46 QSOP Package Outline Removed mechanical drawing of the QSOP package. 46 SSOP Package Outline Added mechanical drawing of the SSOP package. 2.0 Functional Description The ZL38001 device contains an acoustic echo cancellers, as well as the many control functions necessary to operate the echo canceller. The ZL38001 provides clear signal transmission in both audio path directions to ensure reliable voice communication, even with low level signals. The ZL38001 does not use variable attenuators during double-talk or single-talk periods of speech, as do many other acoustic echo cancellers for speakerphones. Instead, the ZL38001 provides high performance full-duplex operation similar to network echo cancellers, so that users experience clear speech and uninterrupted background signals during the conversation. This prevents subjective sound quality problems associated with “noise gating” or “noise contrasting”. The ZL38001 uses an advanced adaptive filter algorithm that is double-talk stable, which means that convergence takes place even while both parties are talking1. This algorithm allows continual tracking of changes in the echo path, regardless of double-talk, as long as a reference signal is available for the echo canceller. The echo tail cancellation capability of the acoustic echo canceller has been sized appropriately (112 ms) to cancel echo in an average sized office with a reverberation time of less than 112 ms. In addition to the echo cancellers, the following functions are supported: • Control of adaptive filter convergence speed during periods of double-talk, far end single-talk and near-end echo path changes • Control of Non-Linear Processor thresholds for suppression of residual non-linear echo • Howling detector to identify when instability is starting to occur and to take action to prevent oscillation • Narrow-Band Detector for preventing adaptive filter divergence caused by narrow-band signals • Offset Nulling filters for removal of DC components in PCM channels • Limiters that introduce controlled saturation levels • Serial controller interface compatible with Motorola, National and Intel microcontrollers • PCM encoder/decodercompatible with/A-Law ITU-T G.711, /A-Law Sign-Mag or linear 2’s complement coding • Automatic gain control on the receive speaker path 2.1 Adaptation Speed Control The adaptation speed of the acoustic echo canceller is designed to optimize the convergence speed versus divergence caused by interfering near-end signals. Adaptation speed algorithm takes into account many different 1. Patent pending. 10 Zarlink Semiconductor Inc. ZL38001 Data Sheet factors such as relative double-talk condition, far end signal power, echo path change and noise levels to achieve fast convergence. 2.2 Advanced Non-Linear Processor (ADV-NLP)1 After echo cancellation, there is likely to be residual echo which needs to be removed so that it will not be audible. The ZL38001 uses an NLP to remove low level residual echo signals which are not comprised of background noise. The operation of the NLP depends upon a dynamic activation threshold, as well as a double-talk detector which disables the NLP during double-talk periods. The ZL38001 keeps the perceived noise level constant, without the need for any variable attenuators or gain switching that causes audible “noise gating”. The noise level is constant and identical to the original background noise even when the NLP is activated. The NLP can be disabled by setting the NLP- bit to 1 in the AEC control registers. 2.3 Narrow Band Signal Detector (NBSD)1 Single or multi-frequency tones (e.g., DTMF or signalling tones) present in the reference input of an echo canceller for a prolonged period of time may cause the adaptive filter to diverge. The Narrow Band Signal Detector (NBSD) is designed to prevent this divergence by detecting single or multi-tones of arbitrary frequency, phase, and amplitude. When narrow band signals are detected, the filter adaptation process is stopped but the echo canceller continues to cancel echo. The NBSD can be disabled by setting the NB- bit to 1 in the MC control registers. 2.4 Howling Detector (HWLD)1 The Howling detector is part of an Anti-Howling control, designed to prevent oscillation as a result of positive feedback in the audio paths. The HWLD can be disabled by setting the AH- bit to 1 in the (MC) control register. 2.5 Offset Null Filter To ensure robust performance of the adaptive filters at all times, any DC offset that may be present on either the Rin signal or the Sin signal, is removed by highpass filters. These filters have a corner frequency placed at 40 Hz. The offset null filters can be disabled by setting the HPF- bit to 1 in the AEC control registers. 2.6 Limiters To prevent clipping in the echo paths, two limiters with variable thresholds are provided at the outputs. The Rout limiter threshold is in Rout Limiter Register 1 and 2. The Sout limiter threshold is in Sout Limiter Register. Both output limiters are always enabled. 2.7 User Gain The user gain function provides the ability for users to adjust the audio gain in the receive path (speaker path). This gain is adjustable from -24 dB to +48 dB in 3 dB steps. It is important to use ONLY this user gain function to adjust the speaker volume. The user gain function in the ZL38001 is optimally placed between the two echo cancellers such that no reconvergence is necessary after gain changes. The gain can be accessed through Receive Gain Control Register. 1. Patent Pending 11 Zarlink Semiconductor Inc. ZL38001 2.8 Data Sheet AGC The AGC function is provided to limit the volume in the speaker path. The gain of the speaker path is automatically reduced during the following conditions: • When clipping of the receive signal occurs • When initial convergence of the acoustic echo canceller detects unusually large echo return • When howling is detected • The AGC can be disabled by setting the AGC- bit to 1 in MC control register 2.9 18 dB Gain Pad at Sout The purpose of the 18 dB gain pad is to improve the subjective quality in low ERL environments. The ZL38001 can cancel echo with a ERL as low as 0 dB (attenuation from Rout to Sin). In many hand free applications, the ERL can be low (or negative). This is due to both speaker and microphone gain setting. The speaker gain has to be set high enough for the speaker to be heard properly and the microphone gain needs to be set high enough to ensure sufficient signal is sent to the far end. If the ERL (Acoustic Attenuation - speaker gain - microphone gain) is greater than 0 dB, then the echo canceller cannot cancel echo. To overcome this limitation, the ZL38001 has a 18 dB gain pad at Sout. The microphone gain can be reduced by 18 dB to allow either the speaker gain and/or the acoustic coupling to be increased by a total of 18 dB allowing more flexibility in the design. 2.10 Mute Function A pcm mute function is provided for independent control of the Receive and Send audio paths. Setting the MUTE_R or MUTE_S bit in the MC register, causes quiet code to be transmitted on the Rout or Sout paths respectively. Quiet code is defined according to the following table. +Zero (quiet code) LINEAR 16 bits 2’s complement SIGN/ MAGNITUDE -Law A-Law 0000h 80h CCITT (G.711) -Law A-Law FFh D5h Table 2 - Quiet PCM Code Assignment 12 Zarlink Semiconductor Inc. ZL38001 2.11 Data Sheet Bypass Control A PCM bypass function is provided to allow transparent transmission of pcm data through the ZL38001. When the bypass function is active, pcm data passes transparently from Rin to Rout and from Sin to Sout, with bit-wise integrity preserved. When the Bypass function is selected, most internal functions are powered down to provide low power consumption. The BYPASS control bit is located in the main control MC register. 2.12 Adaptation Enable/Disable Adaptation control bits are located in the AEC and LEC control registers. When the ADAPT- bit is set to 1, the adaptive filter is frozen at the current state. In this state, the device continues to cancel echo with the current echo model. When the ADAPT- bit is set to 0, the adaptive filter is continually updated. This allows the echo canceller to adapt and track changes in the echo path. This is the normal operating state. 2.13 ZL38001 Throughput Delay In all modes, voice channels always have 2 frames of delay. In ST-BUS/GCI operation, the D and C channels have a delay of one frame. 2.14 Power Down / Reset Holding the RESET pin at logic low will keep the ZL38001 device in a power-down state. In this state all internal clocks are halted, and the DATA1, Sout and Rout pins are tristated. The user should hold the RESET pin low for at least 200 msec following power-up. This will insure that the device powers up in a proper state. Following any return of RESET to logic high, the user must wait for 8 complete 8 KHz frames prior to writing to the device registers. During this time, the initialization routines will execute and set the ZL38001 to default operation (program execution from ROM using default register values). 13 Zarlink Semiconductor Inc. ZL38001 3.0 Data Sheet PCM Data I/O The PCM data transfer for the ZL38001 is provided through two PCM ports. One port consists of Rin and Sout pins while the second port consists of Sin and Rout pins. The data are transferred through these ports according to either ST-BUS, GCI or SSI conventions and the device automatically detects the correct convention. The device determines the convention by monitoring the signal applied to the F0i pin. When a valid ST-BUS (active low) frame pulse is applied to the F0i pin, the ZL38001 will assume ST-BUS operation. When a valid GCI (active high) frame pulse is applied to the F0i pin, the device will assume GCI operation. If F0i is tied continuously to Vss, the device will assume SSI operation. Figures 11 to 13 show timing diagrams of these 3 PCM-interface operation conventions. 3.1 ST-BUS and GCI Operation The ST-BUS PCM interface conforms to Zarlink’s ST-BUS standard with an active-low frame pulse. Input data is clocked in by the rising edge of the bit clock (C4i) three-quarters of the way into the bitcell and output data bit boundaries (Rout, Sout) occur every second falling edge of the bit clock (see Figure 11.) The GCI PCM interface corresponds to the GCI standard commonly used in Europe with an active-high frame pulse. Input data is clocked in by the falling edge of the bit clock (C4i) three-quarters of the way into the bitcell and output data bit boundaries (Rout, Sout) occur every second rising edge of the bit clock (see Figure 12.) Either of these interfaces (STBUS or GCI) can be used to transport 8 bit companded PCM data (using one timeslot) or 16 bit 2’s complement linear PCM data (using two timeslots). The MD1/ENA1 pins select the timeslot on the Rin/Sout port while the MD2/ENA2 pin selects the timeslot on the Sin/Rout port, as in Table 3. Figures 3 to 6 illustrate the timeslot allocation for each of these four modes. C4i start of frame (stbus & GCI) F0i (ST-BUS) 0 1 2 3 4 B F0i (GCI) PORT1 Rin 7 6 5 4 3 2 1 0 EC Sout 7 6 5 4 3 2 1 0 PORT2 Sin 7 6 5 4 3 2 1 0 EC Rout 7 6 5 4 3 2 1 0 outputs = High impedance inputs = don’t care In ST-BUS/GCI Mode 1, echo canceller I/O channels are assigned to ST-BUS/GCI timeslot 0. Note that the user can configure PORT1 and PORT2 into different modes. Figure 3 - ST-BUS and GCI 8-Bit Companded PCM I/O on Timeslot 0 (Mode 1) 14 Zarlink Semiconductor Inc. ZL38001 Data Sheet C4i start of frame (stbus & GCI) F0i (ST-BUS) 0 1 2 3 4 B F0i (GCI) PORT1 Rin 7 6 5 4 3 2 1 0 EC 7 6 5 4 3 2 1 0 Sout PORT2 7 6 5 4 3 2 1 0 Sin EC 7 6 5 4 3 2 1 0 Rout outputs = High impedance inputs = don’t care In ST-BUS/GCI Mode 2, echo canceller I/O channels are assigned to ST-BUS/GCI timeslot 2. Note that the user can configure PORT1 and PORT2 into different modes. Figure 4 - ST-BUS and GCI 8-Bit Companded PCM I/O on Timeslot 2 (Mode 2) 15 Zarlink Semiconductor Inc. ZL38001 Data Sheet C4i start of frame (stbus & GCI) F0i (ST-BUS) 0 D 1 2 C B 3 4 F0i (GCI) PORT1 Rin 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 EC Sout 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 PORT2 Sin 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 EC Rout 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 outputs = High impedance inputs = don’t care indicates that an input channel is bypassed to an output channel ST-BUS/GCI Mode 3 supports connection to 2 B+D devices where timeslots 0 and 1 transport D and C channels and echo canceller (EC) I/O channels are assigned to ST-BUS timeslot 2 (B). Both PORT1 and PORT2 must be configured in Mode 3. Figure 5 - ST-BUS and GCI 8-Bit Companded PCM I/O with D and C channels (Mode 3) 16 Zarlink Semiconductor Inc. ZL38001 Data Sheet C4i start of frame (stbus & GCI) F0i (stbus) F0i (GCI) Rin S 1413 12 11 10 9 8 7 6 5 4 3 2 1 0 PORT1 EC S 1413 12 11 10 9 8 7 6 5 4 3 2 1 0 Sout S 1413 12 11 10 9 8 7 6 5 4 3 2 1 0 Sin PORT2 EC S 1413 12 11 10 9 8 7 6 5 4 3 2 1 0 Rout outputs = High impedance inputs = don’t care ST-BUS/GCI Mode 4 allows 16 bit 2’s complement linear data to be transferred using ST-BUS/GCI I/O timing. Note that PORT1 and PORT2 need not necessarily both be in mode 4. Figure 6 - ST-BUS and GCI 16-Bit 2’s Complement Linear PCM I/O (Mode 4) PORT1 Rin/Sout ST-BUS/GCI Mode Selection Enable Pins MD1 ENA1 0 0 0 PORT2 Sin/Rout Enable Pins MD2 ENA2 Mode 1. 8 bit companded PCM I/O on timeslot 0 0 0 1 Mode 2. 8 bit companded PCM I/O on timeslot 2. 0 1 1 0 Mode 3. 8 bit companded PCM I/O on timeslot 2. Includes D & C channel bypass in timeslots 0 & 1. 1 0 1 1 Mode 4. 16-bit 2’s complement linear PCM I/O on timeslots 0 & 1. 1 1 Table 3 - ST-BUS & GCI Mode Select 3.2 SSI Operation The SSI PCM interface consists of data input pins (Rin, Sin), data output pins (Sout, Rout), a variable rate bit clock (BCLK), and two enable pins (ENA1, ENA2) to provide strobes for data transfers. The active high enable may be either 8 or 16 BCLK cycles in duration. Automatic detection of the data type (8 bit companded or 16-bit 2’s complement linear) is accomplished internally. The data type cannot change dynamically from one frame to the next. 17 Zarlink Semiconductor Inc. ZL38001 Data Sheet In SSI operation, the frame boundary is determined by the rising edge of the ENA1 enable strobe (see Figure 7). The other enable strobe (ENA2) is used for parsing input/output data and it must pulse within 125 microseconds of the rising edge of ENA1. In SSI operation, the enable strobes may be a mixed combination of 8 or 16 BCLK cycles allowing the flexibility to mix 2’s complement linear data on one port (e.g., Rin/Sout) with companded data on the other port (e.g., Sin/Rout). Enable Strobe Pin Designated PCM I/O Port ENA1 Line Side Echo Path (PORT 1) ENA2 Acoustic Side Echo Path (PORT 2) Table 4 - SSI Enable Strobe Pins 3.3 PCM Law and Format Control (LAW, FORMAT) The PCM companding/coding law used by the ZL38001 is controlled through the LAW and FORMAT pins. ITU-T G.711 companding curves for -Law and A-Law are selected by the LAW pin. PCM coding ITU-T G.711 and SignMagnitude are selected by the FORMAT pin. See Table 5. BCLK start of frame (SSI) PORT1 ENA1 8 or 16 bits Rin EC Sout 8 or 16 bits PORT2 ENA2 8 or 16 bits Sin EC 8 or 16 bits Rout outputs = High impedance inputs = don’t care Note that the two ports are independent so that, for example, PORT1 can operate with 8-bit enable strobes and PORT2 can operate with 16-bit enable strobes. Figure 7 - SSI Operations 18 Zarlink Semiconductor Inc. ZL38001 PCM Code Data Sheet Sign-Magnitude ITU-T (G.711) FORMAT=0 FORMAT=1 /A-LAW -LAW A-LAW LAW = 0 or 1 LAW = 0 LAW =1 + Full Scale 1111 1111 1000 0000 1010 1010 + Zero 1000 0000 1111 1111 1101 0101 - Zero 0000 0000 0111 1111 0101 0101 - Full Scale 0111 1111 0000 0000 0010 1010 Table 5 - Companded PCM 3.4 Linear PCM The 16-bit 2’s complement PCM linear coding permits a dynamic range beyond that which is specified in ITU-T G.711 for companded PCM. The echo-cancellation algorithm will accept 16-bits 2’s complement linear code which gives a maximum signal level of +15 dBm0. 3.5 Bit Clock (BCLK/C4i) The BCLK/C4i pin is used to clock the PCM data for GCI and ST-BUS (C4i) interfaces, as well as for the SSI (BCLK) interface. In SSI operation, the bit rate is determined by the BCLK frequency. This input must contain either eight or sixteen clock cycles within the valid enable strobe window. BCLK may be any rate between 128 KHz to 4.096 MHz and can be discontinuous outside of the enable strobe windows defined by ENA1, ENA2 pins. Incoming PCM data (Rin, Sin) are sampled on the falling edge of BCLK while outgoing PCM data (Sout, Rout) are clocked out on the rising edge of BCLK. See Figure 13. In ST-BUS and GCI operation, connect the system C4 (4.096 MHz) clock to the C4i pin. 3.6 Master Clock (MCLK) A nominal 20 MHz, continuously-running master clock (MCLK) is required. MCLK may be asynchronous with the 8 KHz frame. 4.0 Microport The serial microport provides access to all ZL38001 internal read and write registers, plus write-only access to the bootloadable program RAM (see next section for bootload description.) This microport is compatible with Intel MCS-51 (mode 0), Motorola SPI (CPOL=0, CPHA=0) and National Semiconductor Microwire specifications. The microport consists of a transmit/receive data pin (DATA1), a receive data pin (DATA2), a chip select pin (CS) and a synchronous data clock pin (SCLK). The ZL38001 automatically adjusts its internal timing and pin configuration to conform to Intel or Motorola/National requirements. The microport dynamically senses the state of the SCLK pin each time CS pin becomes active (i.e., high to low transition). If SCLK pin is high during CS activation, then Intel mode 0 timing is assumed. In this case DATA1 pin is defined as a bi-directional (transmit/receive) serial port and DATA2 is internally disconnected. If SCLK is low during CS activation, then Motorola/National timing is assumed and DATA1 is defined as the data transmit pin while DATA2 becomes the data receive pin. The ZL38001 supports Motorola half-duplex processor mode (CPOL=0 19 Zarlink Semiconductor Inc. ZL38001 Data Sheet and CPHA=0). This means that during a write to the ZL38001, by the Motorola processor, output data from the DATA1 pin must be ignored. This also means that input data on the DATA2 pin is ignored by the ZL38001 during a valid read by the Motorola processor. All data transfers through the microport are two bytes long. This requires the transmission of a Command/Address byte followed by the data byte to be written to or read from the addressed register. CS must remain low for the duration of this two-byte transfer. As shown in Figures 8 and 9, the falling edge of CS indicates to the ZL38001 that a microport transfer is about to begin. The first 8 clock cycles of SCLK after the falling edge of CS are always used to receive the Command/Address byte from the microcontroller. The Command/Address byte contains information detailing whether the second byte transfer will be a read or a write operation and at what address. The next 8 clock cycles are used to transfer the data byte between the ZL38001 and the microcontroller. At the end of the two-byte transfer, CS is brought high again to terminate the session. The rising edge of CS will tri-state the DATA1 pin. The DATA1 pin will remain tri-stated as long as CS is high. Intel processors utilize Least Significant Bit (LSB) first transmission while Motorola/National processors use Most Significant Bit (MSB) first transmission. The ZL38001 microport automatically accommodates these two schemes for normal data bytes. However, to ensure timely decoding of the R/W and address information, the Command/Address byte is defined differently for Intel and Motorola/National operations. Refer to the relative timing diagrams of Figure 8 and Figure 9. Receive data bits are sampled on the rising edge of SCLK while transmit data is clocked out on the falling edge of SCLK. Detailed microport timing is shown in Figure 14 and Figure 15. 4.1 Bootload Process and Execution from RAM A bootloadable program RAM (BRAM) is available on the ZL38001 to support factory-issued software upgrades to the built-in algorithm. To make use of this bootload feature, users must include 4096 X 8 bits of memory in their microcontroller system (i.e., external to the ZL38001), from which the ZL38001 can be bootloaded. Registers and program data are loaded into the ZL38001 in the same fashion via the serial microport. Both employ the same command / address / data byte specification described in the previous section on serial microport. Either intel or motorola mode may be transparently used for bootloading. There are also two registers relevant to bootloading (BRC=control and SIG=signature, see Register Summary). The effect of these register values on device operation is summarized in Table 6. Bootload mode is entered and exited by writing to the bootload bit in the Bootload RAM Control (BRC) register at address 3fh (see Register Summary). During bootload mode, any serial microport "write" (R/W command bit =0) to an address other than that of the BRC register will contribute to filling the program BRAM. Call these transactions "BRAM-fill" writes. Although a command/address byte must still precede each data byte (as described for the serial microport), the values of the address fields for these "BRAM-fill" writes are ignored (except for the value 3fh, which designates the BRC register.) Instead, addresses are internally generated by the ZL38001 for each "BRAM-fill" write. Address generation for "BRAM-fill" writes resumes where it left off following any read transaction while bootload mode is enabled. The first 4096 such "BRAM-fill" writes while bootload is enabled will load the memory, but further ones after that are ignored. Following the write of the first 4096 bytes, the program BRAM will be filled. Before bootload mode is disabled, it is recommended that users then read back the value from the signature register (SIG) and compare it to the one supplied by the factory along with the code. Equality verifies that the correct data has been loaded. The signature calculation uses an 8-bit MISR which only incorporates input from "BRAM-fill" writes. Resetting the bootload bit (C2) in the BRC register to 0 (see Register Summary) exits bootload mode, resetting the signature (SIG) register and internal address generator for the next bootload. A hardware reset (RESET=0) similarly returns the ZL38001 to the ready state for the start of a bootload. 20 Zarlink Semiconductor Inc. ZL38001 Data Sheet FUNCTIONAL DESCRIPTION FOR USING THE BOOTABLE RAM BOOTLOAD MODE - Microport Access is to bootload RAM (BRAM) BRC Register Bits C3C2C1C0 R/W Address Data W 3fh (= 1 1 1 1 1 1 b) Writes "data" to BRC reg. - Bootload frozen; BRAM contents are NOT affected. W other than 3fh Writes "data" to next byte in BRAM (bootloading.) R 1x xxxxb Reads back "data" = BRC reg value. - Bootload frozen; BRAM contents are NOT affected. R 0x xxxxb Reads back "data" = SIG reg value. - Bootload frozen; BRAM contents are NOT affected. X 1 0 0 NON-BOOTLOAD MODE - Microport Access is to device registers (DREGs) BRC Register Bits C3C2C1C0 R/W X 0 0 0 R Address W Data any (= a5 a4 a3 a2 a1 a0 Writes "data" to corresponding DREG. b) any (= a5 a4 a3 a2 a1 a0 Reads back "data" = corresponding DREG value. b) PROGRAM EXECUTION MODES C3C2C1C0 0 0 0 0 Execute program in ROM, bootload mode disabled. - BRAM address counter reset to initial (ready) state. - SIG reg reseeded to initial (ready) state C3C2C1C0 0 1 0 0 Execute program in ROM, while bootloading the RAM. - BRAM address counter increments on microport writes (except to 3fh) - SIG reg recalculates signature on microport writes (except to 3fh) C3C2C1C0 1 0 0 0 Execute program in RAM, bootload mode disabled. - BRAM address counter reset to initial (ready) state. - SIG reg reseeded to initial (ready) state C3C2C1C0 1 1 0 0 - NOT RECOMMENDED (Execute program in RAM, while bootloading the RAM) Table 6 - Bootload RAM Control (BRC) Register States Note: bits C1 C0 are reserved, and must be set to zero. 21 Zarlink Semiconductor Inc. ZL38001 Data Sheet Once the program has been loaded, to begin execution from RAM, bootload mode must be disabled (BOOT bit, C2=0) and execution from RAM enabled (RAM_ROMb bit, C3=1) by setting the appropriate bits in the BRC register. During the bootload process, however, ROM program execution (RAM_ROMb bit, C3=0) should be selected. See Table 6 for the effect of the BRC register settings on Microport accesses and on program execution. Following program loading and enabling of execution from RAM, it is recommended that users set the software reset bit in the Main Control (MC) register, to ensure that the device updates the default register values to those of the new program in RAM. Note: it is important to use a software reset rather than a hardware (RESET=0) reset, as the latter will return the device to its default settings (which includes execution from program ROM instead of RAM.) To verify which code revision is currently running, users can access the Firmware Revision Code (FRC) register (see Register Summary). This register reflects the identity code (revision number) of the last program to run register initialization (which follows a software or hardware reset.) COMMAND/ADDRESS e DATA 1 R/W A0 A1 A2 A3 A4 A5 DATA INPUT/OUTPUT D0 D1 D2 D3 D4 D5 D6 D7 X a SCLK b CS d c a b This delay is due to internal processor timing and is equal to Tsch time. The delay is transparent to ZL38001. The ZL38001: latches receive data on the rising edge of SCLK outputs transmit data on the falling edge of SCLK c The falling edge of CS indicates that a COMMAND/ADDRESS byte will be transmitted from the microprocessor. The subsequent byte is always data followed by CS returning high. d A new COMMAND/ADDRESS byte may be loaded only by CS cycling high then low again. e The COMMAND/ADDRESS byte contains: 1 bit - Read/Write 6 bits - Addressing Data 1 bit - Unused Figure 8 - Serial Microport Timing for Intel Mode 0 22 Zarlink Semiconductor Inc. ZL38001 COMMAND/ADDRESS e DATA 2 Receive R/W A5 A4 A3 A2 A1 A0 Data Sheet DATA INPUT X D7 D6 D5 D4 D3 D2 D1 D0 DATA OUTPUT DATA 1 Transmit D7 D6 D5 D4 D3 D2 D1 D0 High Impedance a SCLK b CS d c a This delay is due to internal processor timing and is equal to Tsch time. The delay is transparent to ZL38001. b The ZL38001: latches receive data on the rising edge of SCLK outputs transmit data on the falling edge of SCLK c The falling edge of CS indicates that a COMMAND/ADDRESS byte will be transmitted from the microprocessor. The subsequent byte is always data followed by CS returning high. d A new COMMAND/ADDRESS byte may be loaded only by CS cycling high then low again. e The COMMAND/ADDRESS byte contains: 1 bit - Read/Write 6 bits - Addressing Data 1 bit - Unused Figure 9 - Serial Microport Timing for Motorola Mode 00 or National Microwire 23 Zarlink Semiconductor Inc. ZL38001 Data Sheet Absolute Maximum Ratings* Parameter Symbol Min. Max. Units VDD-VSS -0.5 5.0 V 1 Supply Voltage 2 Input Voltage Vi VSS-0.3 5.5 V 3 Output Voltage Swing Vo VSS-0.3 5.5 V 4 Continuous Current on any digital pin Ii/o 20 mA 5 Storage Temperature TST 150 C -65 90 (typ) 6 Package Power Dissipation PD * Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied. mW Recommended Operating Conditions - Voltages are with respect to ground (VSS) unless otherwise stated. Characteristics Sym. Min. Typ. Max. Units VDD 2.7 3.3 3.6 V 1 Supply Voltage 2 Input High Voltage 1.4 VDD V 3 Input Low Voltage VSS 0.4 V 4 Operating Temperature TA -40 +85 C Min. Typ. Test Conditions Echo Return Limits Characteristics Max. Units Test Conditions 1 Acoustic Echo Return 0 dB Measured from Rout -> Sin 2 Line Echo Return 0 dB Measured from Sout -> Rin DC Electrical Characteristics*- Voltages are with respect to ground (VSS) unless otherwise stated. Characteristics Sym. Min. Typ.‡ Max. Units 70 A RESET = 0 mA RESET = 1, clocks active Standby Supply Current: ICC 3 Operating Supply Current: IDD 20 2 Input HIGH voltage VIH 3 Input LOW voltage VIL 4 Input leakage current IIH/IIL 5 High level output voltage VOH 6 Low level output voltage VOL 7 High impedance leakage IOZ 1 8 Output capacitance Co 10 1 0.7VDD Conditions/Notes V 0.1 0.3VDD V 10 A VIN=VSS to VDD V IOH=2.5 mA 0.4VDD V IOL=5.0 mA 10 A VIN=VSS to VDD 0.8VDD pF 8 pF 9 Input capacitance Ci ‡ Typical figures are at 25C and are for design aid only: not guaranteed and not subject to production testing. *DC Electrical Characteristics are over recommended temperature and supply voltage. 24 Zarlink Semiconductor Inc. ZL38001 Data Sheet AC Electrical Characteristics† - Serial Data Interfaces - Voltages are with respect to ground (VSS) unless otherwise stated. Characteristics Sym. Min. Typ. Max. Units 20.5 MHz Test Notes 1 MCLK Frequency fCLK 19.15 2 BCLK/C4i Clock High tBCH, tC4H 90 ns 3 BCLK/C4i Clock Low tBLL, tC4L 90 ns 4 BCLK/C4i Period tBCP 240 5 SSI Enable Strobe to Data Delay (first bit) tSD 80 ns CL = 150 pF 6 SSI Data Output Delay (excluding first bit) tDD 80 ns CL = 150 pF 7 SSI Output Active to High Impedance tAHZ 80 ns CL = 150 pF 8 SSI Enable Strobe Signal Setup tSSS 10 tBCP -15 ns 9 SSI Enable Strobe Signal Hold tSSH 15 tBCP -10 ns 10 SSI Data Input Setup tDIS 10 ns 11 SSI Data Input Hold tDIH 15 ns 12 ST-BUS/GCI F0i Setup tF0iS 20 150 ns 13 ST-BUS/GCI F0i Hold tF0iH 20 150 ns 14 ST-BUS/GCI Data Output delay tDSD 80 ns CL = 150 pF 15 ST-BUS/GCI Output Active to High Impedance tASHZ 80 ns CL = 150 pF 16 ST-BUS/GCI Data Input Hold time tDSH 20 ns 17 ST-BUS/GCI Data Input Setup time tDSS 20 ns † Timing is over recommended temperature and power supply voltages. 25 Zarlink Semiconductor Inc. 7900 ns ZL38001 Data Sheet AC Electrical Characteristics† - Microport Timing Characteristics Sym. Min. Typ. Max. Units 1 Input Data Setup tIDS 30 ns 2 Input Data Hold tIDH 30 ns 3 Output Data Delay tODD 100 ns 4 Serial Clock Period tSCP 500 ns 5 SCLK Pulse Width High tSCH 250 ns 6 SCLK Pulse Width Low tSCL 250 ns 7 CS Setup-Intel tCSSI 200 ns 8 CS Setup-Motorola tCSSM 100 ns 9 CS Hold tCSH 100 ns 10 CS to Output High Impedance tOHZ 100 ns Test Notes CL = 150 pF CL = 150 pF † Timing is over recommended temperature range and recommended power supply voltages. Characteristic Symbol CMOS Level Units CMOS reference level VCT 0.5*VDD V Input HIGH level VH 0.9*VDD V Input LOW level VL 0.1*VDD V Rise/Fall HIGH measurement point VHM 0.7*VDD V Rise/Fall LOW measurement point VLM 0.3*VDD V Table 7 - Reference Level Definition for Timing Measurements T=1/fCLK MCLK (I) VH VCT VL Notes: O. CMOS output I. CMOS input (5 V tolerant) (see Table 8 for symbol definitions) Figure 10 - Master Clock - MCLK 26 Zarlink Semiconductor Inc. ZL38001 Bit 7 Data Sheet Bit 6 Sout/Rout (O) VCT tDSD C4i (I) tASHZ tC4H VH VCT input sampled VL tF0iS tF0iH F0i (I) VH tC4L VCT VL start of frame Rin/Sin (I) tDSS tDSH VH VCT VL Bit 6 Bit 7 Figure 11 - GCI Data Port Timing Bit 7 Bit 6 Sout/Rout (O) VCT tDSD VH VCT VL tF0iS tF0iH F0i (I) tASHZ VH input sampled C4i (I) tC4H tC4L VCT VL start of frame Rin/Sin (I) tDSS tDSH VH VCT VL Bit 7 Bit 6 Figure 12 - ST-BUS Data Port Timing 27 Zarlink Semiconductor Inc. ZL38001 Bit 7 Bit 6 Data Sheet Bit 5 VCT Sout/Rout (O) tSD tDD tAHZ tBCH VH BCLK (I) VCT tSSS input sampled VL tBCP VH ENA1 (I) or ENA2 (I) tBCL tSSH VCT VL tDIS tDIH start of frame VH VCT Rin/Sin (1) VL Bit 7 Notes: O. CMOS output Bit 6 Bit 5 I. CMOS input (5 V tolerant) (see Table 8 for symbol definitions) Figure 13 - SSI Data Port Timing DATA OUTPUT DATA INPUT DATA1 (I,O) VCT tIDS tIDH SCLK (I) tSCH tODD tOHZ VH VCT VL tCSSI CS (I) tSCL tSCP tCSH VH VCT VL Notes: O. CMOS output I. CMOS input (5 V tolerant) (see Table 8 for symbol definitions) Figure 14 - INTEL Serial Microport Timing 28 Zarlink Semiconductor Inc. ZL38001 DATA2 (I) (Input) VH VCT VL tIDS tIDH SCLK (I) Data Sheet tSCH tSCP VH VCT VL tCSSM CS (I) tSCL tCSH VH VCT VL tODD DATA1 (O) (Output) tOHZ VCT Notes: O. CMOS output I. CMOS input (5 V tolerant) (see Table 8 for symbol definitions) Figure 15 - Motorola Serial Microport Timing 29 Zarlink Semiconductor Inc. ZL38001 5.0 Data Sheet Register Summary External Read/Write Address: 00H Reset Value: 00H 7 6 5 4 3 2 1 0 LIMIT MUTE_R MUTE_S BYPASS NB- AGC- AH- RESET Bit Name Description 7 LIMIT 6 MUTE_R When high, the Rin path is muted to quite code (after the NLP) and when low the Rin path is not muted. 5 MUTE_S When high, the Sin path is muted to quite code (after the NLP) and when low the Sin path is not muted. 4 BYPASS When high, the Send and Receive paths are transparently by-passed from input to output and when low the Send and Receive paths are not bypassed. 3 NB- 2 AGC- 1 AH- 0 RESET When high, the 2-bit shift mode is enabled in conjunction with bit 7 of LEC register and when low 2-bit shift mode is disabled. Default limit for Rin and Sin is 3.14 dBm0. When high, Narrowband signal detectors in Rin and Sin paths are disabled and when low the signal detectors are enabled. When high, AGC is disabled and when low AGC is enabled. When high, the Howling detector is disabled and when low the Howling detector is enabled. When high, the power initialization routine is executed presetting all registers to default values. This bit automatically clears itself to ’0’ when reset is complete. Register Table 1 - Main Control Register (MC) External Read/Write Address:21H Reset Value: 00H 7 6 5 4 3 2 1 0 P- ASC- NLP- INJ- HPF- HCLR ADAPT- ECBY Bit Name Description 7 P- 6 ASC- When high, the Internal Adaptation speed control is disabled and when low the Adaptation speed is enabled. 5 NLP- When high, the Non Linear Processor is disabled in the Sin/Sout path and when low the NLP is enabled. When high, the Exponential weighting function for the adaptive filter is disabled and when low the weighting function is enabled Register Table 2 - Acoustic Echo Canceller Control Register (AEC) 30 Zarlink Semiconductor Inc. ZL38001 Data Sheet External Read/Write Address:21H Reset Value: 00H 7 6 5 4 3 2 1 0 P- ASC- NLP- INJ- HPF- HCLR ADAPT- ECBY Bit Name Description 4 INJ- When high, the Noise filtering process is disabled in the NLP and when low the Noise filtering process is enabled. 3 HPF- When high, Offset nulling filter is bypassed in the Sin/Sout path and when low the Offset nulling filter in not bypassed. 2 HCLR When high, Adaptive filter coefficients are cleared and when low the filter coefficients are not cleared 1 ADAPT- When high, the Echo canceller adaptation is disabled and when low the adaptation is enabled. 0 ECBY When high, the Echo estimate from the filter is not subtracted from the input (Sin), when low the estimate is subtracted. Register Table 2 - Acoustic Echo Canceller Control Register (AEC) (continued) External Read/Write Address: 01H Reset Value: 00H 7 6 5 4 3 2 1 0 SHFT ASC- NLP- INJ- HPF- HCLR ADAPT- ECBY Bit Name Description 7 SHFT When high the 16-bit linear mode, inputs Sin, Rin, are shift right by 2 and outputs Sout, Rout are shift left by 2. This bit is ignored when 16-bit linear mode is not selected in both ports. This bit is also ignored if bit 7 of MC register is set to zero. 6 ASC- When high, the Internal Adaptation speed control is disabled and when low the Adaptation speed is enabled. 5 NLP- When high, the Non Linear Processor is disabled in the Rin/Rout path and when low the NLP is enabled. 4 INJ- When high, the Noise filtering process is disabled in the NLP and when low the Noise filtering process is enabled. 3 HPF- When high, Offset nulling filter is bypassed in the Rin/Rout path and when low the Offset nulling filter in not bypassed. 2 HCLR When high, Adaptive filter coefficients are cleared and when low the filter coefficients are not cleared. Register Table 3 - Line Echo Canceller Control Register (LEC) 31 Zarlink Semiconductor Inc. ZL38001 Data Sheet External Read/Write Address: 01H Reset Value: 00H 7 6 5 4 3 2 1 0 SHFT ASC- NLP- INJ- HPF- HCLR ADAPT- ECBY Bit Name 1 ADAPT- 0 ECBY Description When high, the Echo canceller adaptation is disabled and when low the adaptation is enabled. When high, the Echo estimate from the filter is not substracted from the input (Rin), when low the estimate is substracted. Register Table 3 - Line Echo Canceller Control Register (LEC) (continued) External Read Address: 22H Reset Value: 00H 7 6 5 4 3 2 1 0 - ACMUND HWLNG - NLPDC DT NB NBS Bit Name Description 7 - 6 ACMUND 5 HWLNG 4 - 3 NLPDC 2 DT When high the Double Talk is detected and when low, the Double talk is not detected. 1 NB LOGICAL OR of the status bit NBS + NBR from LSR Register. 0 NBS RESERVED. When low, No active signal in the Rin/Rout path. When high, Howling is occurring in the loop and when low, no Howling is detected. RESERVED. When high, the NLP is activated and when low the NLP is not activated. When high, the Narrowband signal has been detected in the Sin/Sout path and when low, the Narrowband signal has not been detected in the Sin/Sout path. Register Table 4 - Acoustic Echo Canceller Status Register (ASR) (* Do not write to this register) 32 Zarlink Semiconductor Inc. ZL38001 Data Sheet External Read Address: 02H Reset Value: 00H 7 6 5 4 3 2 1 0 Bit Name Description 7 - 6 - 5 - 4 - 3 NLPC 2 DT When high, double-talk is detected and when low double-talk is not detected. 1 NB This bit indicates a LOGICAL-OR of Status bits NBR + NBS (from ASR Register). 0 NBR RESERVED. When high, NLP is activated and when low NLP is not activated. When high, a narrowband signal has been detected in the Receive (Rin) path. When low no narrowband signal is not detected in the Rin path. Register Table 5 - Line Echo Canceller Status Register (LSR) (* Do not write to this register) 33 Zarlink Semiconductor Inc. ZL38001 Data Sheet External Read/Write Address:20H Reset Value: 6DH 7 6 5 4 3 2 1 0 - - - G4 G3 G2 G1 G0 Bit Name Description 7 Reserved Must keep as Logic 0. 6 Reserved Must keep as Logic 1. 5 Reserved Must keep as Logic 1. 4-0 G4-0 User Gain Control on the Rin/Rout path (Tolerance of gains: +/- 0.15 dB). The hexadecimal number represents G3 to G0 value in the table below. Register Value Gain Register Value Gain 0h -24 dB 10h +24 dB 1h -21 dB 11h +27 dB 2h -18 dB 12h +30 dB 3h -15 dB 13h +33 dB 4h -12 dB 14h +36 dB 5h -9 dB 15h +39 dB 6h -6 dB 16h +42 dB 7h -3 dB 17h +45 dB 8h 0 dB 18h +48 dB 9h +3 dB 19h Reserved Ah +6 dB 1Ah Reserved Bh +9 dB 1Bh Reserved Ch +12 dB 1Ch Reserved Dh +15 dB 1Dh Reserved Eh +18 dB 1Eh Reserved Fh +21 dB 1Fh Reserved Register Table 6 - Receive Gain Control Register 34 Zarlink Semiconductor Inc. ZL38001 Data Sheet External Read/Write Address: 32H Reset Value: 25H 7 6 5 4 3 2 1 0 HG2 HG1 HG0 DTGain - - - - Bit Name Description 7 - RESERVED. Must keep as 0. 6 - RESERVED. Must keep as 0. 5 - RESERVED. Must keep as 1. 4 DTRGain 3 - RESERVED. Must keep as 0. 2 - RESERVED. Must keep as 1. 1 - RESERVED. Must keep as 0. 0 - RESERVED. Must keep as 1. This bit controls the gain level at Rout during double talk. When this bit is high 12 dB of attenuation is injected into the Rout path during double talk. When this bit is low the gain pad is disabled. Register Table 7 - Double Talk Gain Control Register 1 (DTGCR1) External Read/Write Address: 12H Reset Value: 00H 7 6 5 4 - - - DTSGain 3 Bit Name 7 - RESERVED. Must keep as 0. 6 - RESERVED. Must keep as 0. 5 - RESERVED. Must keep as 0. 4 DTSGain 3 - RESERVED. Must keep as 0. 2 - RESERVED. Must keep as 0. 1 - RESERVED. Must keep as 0. 0 - RESERVED. Must keep as 0. 2 1 - - 0 Description This bit controls the gain level at Sout during double talk. When this bit is high 12 dB of attenuation is injected into the Sout path during double talk. When this bit is low the gain pad is disabled. Register Table 8 - Double Talk Gain Control Register 2 (DTGCR2) 35 Zarlink Semiconductor Inc. ZL38001 Data Sheet External Read/Write Address: 31H Reset Value: 21H 7 6 5 4 3 2 1 0 DTDT2 DTDT1 DTDT0 - - - - - Bit Name Description 7 DTDT2 6 DTDT1 DTDT2, DTDT1, DTDT0 Value DTDT DTDT2, DTDT1, DTDT0 Value DTDT 5 DTDT0 000 -12 dB 100 +12 dB 001 -6 dB 101 +18 dB 010 0 dB 110 +24 dB 011 +6 dB 111 +30 dB 4 - RESERVED. Must keep as 0. 3 - RESERVED. Must keep as 0. 2 - RESERVED. Must keep as 0. 1 - RESERVED. Must keep as 0. 0 - RESERVED. Must keep as 1. Register Table 9 - Double Talk detection Threshold Register (DTDT) External Read Address: 16H Reset Value: 00H 7 6 5 4 3 2 1 0 RIPD7 RIPD6 RIPD5 RIPD4 RIPD3 RIPD2 RIPD1 RIPD0 Bit Name Description 7 RIPD7 6 RIPD6 5 RIPD5 These peak detector registers allow the user to monitor the receive in signal (Rin) peak level at reference point R1 (see Figure 1). The information is in 16bit 2’s complement linear coded format presented in two 8-bit registers. The high byte is in Register 2 and the low byte is in Register 1. 4 RIPD4 3 RIPD3 2 RIPD2 1 RIPD1 0 RIPD0 Register Table 10 - Receive (Rin) Peak Detect Register 1 (RIPD1) 36 Zarlink Semiconductor Inc. ZL38001 Data Sheet External Read Address: 17H Reset Value: 00H 7 6 5 4 3 2 1 0 RIPD15 RIPD14 RIPD13 RIPD12 RIPD11 RIPD10 RIPD9 RIPD8 Bit Name Description 7 RIPD15 6 RIPD14 5 RIPD13 These peak detector registers allow the user to monitor the receive in signal (Rin) peak level at reference point R1 (see Figure 1). The information is in 16bit 2’s complement linear coded format presented in two 8-bit registers. The high byte is in Register 2 and the low byte is in Register 1. 4 RIPD12 3 RIPD11 2 RIPD10 1 RIPD9 0 RIPD8 Register Table 11 - Receive (Rin) Peak Detect Register 2 (RIPD2) External Read Address: 18H Reset Value: 00H 7 6 5 4 3 2 1 0 REPD7 REPD6 REPD5 REPD4 REPD3 REPD2 REPD1 REPD0 Bit Name Description 7 REPD7 6 REPD6 5 REPD5 These peak detector registers allow the user to monitor the error signal peak level at reference point R2 (see Figure 1). The information is in 16-bit 2’s complement linear coded format presented in two 8-bit registers. The high byte is in Register 2 and the low byte is in Register 1. 4 REPD4 3 REPD3 2 REPD2 1 REPD1 0 REPD0 Register Table 12 - Receive (Rin) ERROR Peak Detect Register 1 (REPD1) 37 Zarlink Semiconductor Inc. ZL38001 Data Sheet External Read Address: 19H Reset Value: 00H 7 6 5 4 3 2 1 0 REPD15 REPD14 REPD13 REPD12 REPD11 REPD10 REPD9 REPD8 Bit Name Description 7 REPD15 6 REPD14 5 REPD13 These peak detector registers allow the user to monitor the error signal peak level at reference point R2 (see Figure 1). The information is in 16-bit 2’s complement linear coded format presented in two 8-bit registers. The high byte is in Register 2 and the low byte is in Register 1. 4 REPD12 3 REPD11 2 REPD10 1 REPD9 0 REPD8 Register Table 13 - Receive (Rin) ERROR Peak Detect Register 2 (REPD2) External Read Address: 3AH Reset Value: 00H 7 6 5 4 3 2 1 0 ROPD7 ROPD6 ROPD5 ROPD4 ROPD3 ROPD2 ROPD1 ROPD0 Bit Name Description 7 ROPD7 6 ROPD6 5 ROPD5 These peak detector registers allow the user to monitor the receive out signal (Rout) peak level at reference point R3 (see Figure 1). The information is in 16-bit 2’s complement linear coded format presented in two 8-bit registers. The high byte is in Register 2 and the low byte is in Register 1. 4 ROPD4 3 ROPD3 2 ROPD2 1 ROPD1 0 ROPD0 Register Table 14 - Receive (Rout) Peak Detect Register 1 (ROPD1) 38 Zarlink Semiconductor Inc. ZL38001 Data Sheet External Read Address: 3BH Reset Value: 00H 7 6 5 4 3 2 1 0 ROPD15 ROPD14 ROPD13 ROPD12 ROPD11 ROPD10 ROPD9 ROPD8 Bit Name Description 7 ROPD15 6 ROPD14 5 ROPD13 These peak detector registers allow the user to monitor the receive out signal (Rout) peak level at reference point R3 (see Figure 1). The information is in 16-bit 2’s complement linear coded format presented in two 8-bit registers. The high byte is in Register 2 and the low byte is in Register 1. 4 ROPD12 3 ROPD11 2 ROPD10 1 ROPD9 0 ROPD8 Register Table 15 - Receive (Rout) Peak Detect Register 2 (ROPD2) External Read Address: 36H Reset Value: 00H 7 6 5 4 3 2 1 0 SIPD7 SIPD6 SIPD5 SIPD4 SIPD3 SIPD2 SIPD1 SIPD0 Bit Name Description 7 SIPD7 6 SIPD6 5 SIPD5 These peak detector registers allow the user to monitor the receive in signal (Sin) peak level at reference point S1 (see Figure 1). The information is in 16bit 2’s complement linear coded format presented in two 8-bit registers. The high byte is in Register 2 and the low byte is in Register 1. 4 SIPD4 3 SIPD3 2 SIPD2 1 SIPD1 0 SIPD0 Register Table 16 - Send (Sin) Peak Detect Register 1 (SIPD1) 39 Zarlink Semiconductor Inc. ZL38001 Data Sheet External Read Address: 37H Reset Value: 00H 7 6 5 4 3 2 1 0 SIPD15 SIPD14 SIPD13 SIPD12 SIPD11 SIPD10 SIPD9 SIPD8 Bit Name Description 7 SIPD15 6 SIPD14 5 SIPD113 These peak detector registers allow the user to monitor the receive in signal (Sin) peak level at reference point S1 (see Figure 1). The information is in 16bit 2’s complement linear coded format presented in two 8-bit registers. The high byte is in Register 2 and the low byte is in Register 1. 4 SIPD12 3 SIPD11 2 SIPD10 1 SIPD9 0 SIPD8 Register Table 17 - Send (Sin) Peak Detect Register 2 (SIPD2) External Read Address: 38H Reset Value: 00H 7 6 5 4 3 2 1 0 SEPD7 SEPD6 SEPD5 SEPD4 SEPD3 SEPD2 SEPD1 SEPD0 Bit Name Description 7 SEPD7 6 SEPD6 5 SEPD5 These peak detector registers allow the user to monitor the error signal peak level in the send path at reference point S2 (see Figure 1). The information is in 16-bit 2’s complement linear coded format presented in two 8-bit registers. The high byte is in Register 2 and the low byte is in Register 1. 4 SEPD4 3 SEPD3 2 SEPD2 1 SEPD1 0 SEPD0 Register Table 18 - Send ERROR Peak Detect Register 1 (SEPD1) 40 Zarlink Semiconductor Inc. ZL38001 Data Sheet External Read Address: 39H Reset Value: 00H 7 6 5 4 3 2 1 0 SEPD15 SEPD14 SEPD13 SEPD12 SEPD11 SEPD10 SEPD9 SEPD8 Bit Name Description 7 SEPD15 6 SEPD14 5 SEPD13 These peak detector registers allow the user to monitor the error signal peak level in the send path at reference point S2 (see Figure 1). The information is in 16-bit 2’s complement linear coded format presented in two 8-bit registers. The high byte is in Register 2 and the low byte is in Register 1. 4 SEPD12 3 SEPD11 2 SEPD10 1 SEPD9 0 SEPD8 Register Table 19 - Send ERROR Peak Detect Register 2 (SEPD2) External Read Address: 1AH Reset Value: 00H 7 6 5 4 3 2 1 0 SOPD7 SOPD6 SOPD5 SOPD4 SOPD3 SOPD2 SOPD1 SOPD0 Bit Name 7 SOPD7 6 SOPD6 5 SOPD5 4 SOPD4 3 SOPD3 2 SOPD2 1 SOPD1 0 SOPD0 Description These peak detector registers allow the user to monitor the Send out signal (Sout) peak level at reference point S3 (see Figure 1). The information is in 16-bit 2’s complement linear coded format presented in two 8-bit registers. The high byte is in Register 2 and the low byte is in Register 1. Register Table 20 - Send (Sout) Peak Detect Register 1 (SOPD1) 41 Zarlink Semiconductor Inc. ZL38001 Data Sheet External Read Address: 1BH Reset Value: 00H 7 6 5 4 3 2 1 0 SOPD15 SOPD14 SOPD13 SOPD12 SOPD11 SOPD10 SOPD9 SOPD8 Bit Name 7 SOPD15 6 SOPD14 5 SOPD13 4 SOPD12 3 SOPD11 2 SOPD10 1 SOPD9 0 SOPD8 Description These peak detector registers allow the user to monitor the Send out signal (Sout) peak level at reference point S3 (see Figure 1). The information is in 16-bit 2’s complement linear coded format presented in two 8-bit registers. The high byte is in Register 2 and the low byte is in Register 1. Register Table 21 - Send (Sout) Peak Detect Register 2 (SOPD2) External Read Address: 24H Reset Value: 80H 7 6 5 4 3 2 1 0 L0 - - - - - - - Bit Name 7 L0 6 - 5 - 4 - 3 - 2 - 1 - 0 - Description This bit is used in conjunction with Rout Limiter Register 2. (See description below.) RESERVED Register Table 22 - Rout Limiter Register 1 (RL1) 42 Zarlink Semiconductor Inc. ZL38001 Data Sheet External Read Address: 25H Reset Value: 3EH 7 6 5 4 3 2 1 0 L8 L7 L6 L5 L4 L3 L2 L1 Bit Name Description 7 L8 6 L7 In conjunction with bit 7 (L0) of the above (RL1) register, this register (RL2) allows the user to program the output Limiter threshold value in the Rout path. 5 L6 4 L5 3 L4 2 L3 1 L2 0 L1 Default value is (07D)h which is equal to 3.14 dBmo Maximum value is (1FF)h = 15 dBmo Minimum value is (001)h = -38 dBmo Register Table 23 - Rout Limiter Register 2 (RL2) External Read Address: 26H Reset Value: 3DH 7 6 5 4 3 L4 L3 L2 L1 L0 2 1 0 Bit Name Description 7 L4 6 L3 This register allows the user to program the output Limiter threshold value in the Rout path. 5 L2 4 L1 3 L0 2 - RESERVED. Must be keep as 1. 1 - RESERVED. Must be keep as 0. 0 - RESERVED. Must be keep as 1. Default value is (1D)h which is equal to 3.14 dBmo Maximum value is (1F)h Register Table 24 - Sout Limiter Register (SL) 43 Zarlink Semiconductor Inc. ZL38001 Data Sheet External Read Address: 03H Reset Value: 00H 7 6 5 4 3 2 1 0 FRC2 FRC1 FRC0 - - - - - Bit Name Description 7 FRC2 Revision code of the firmware program currently being run (default=rom=00). 6 FRC1 5 FRC0 4 - 3 - 2 - 1 - 0 - RESERVED Register Table 25 - Firmware Revision Code Register (FRC) External Read Address: 3FH Reset Value: 00H 7 6 5 4 3 2 1 0 - - - - C3 C2 C1 C0 Bit Name Description 7 - 6 - 5 - 4 - 3 C3 RAM_ROMb bit. When high, device executes from RAM. When low, device executes from ROM. 2 C2 BOOT bit. When high, puts device in bootload mode. When low, bootload is disabled. 1 C1 RESERVED. Must be set to zero. 0 C0 RESERVED. Must be set to zero. RESERVED Register Table 26 - Bootload RAM Control Register (BRC) 44 Zarlink Semiconductor Inc. ZL38001 Data Sheet External Read Address: 07H Reset Value: 10H 7 6 5 4 3 2 1 0 SIG7 SIG6 SIG5 SIG4 SIG3 SIG2 SIG1 SIG0 Bit Name Description 7 SIG7 6 SIG6 5 SIG5 4 SIG4 This register provides the signature of the bootloaded data to verify error-free delivery into the device. Note: this register is only accessible if BOOT bit is high (bootload mode enabled) in the above BRC register. While bootload is disabled, the register value is held constant at its reset seed value of FFh. 3 SIG3 2 SIG2 1 SIG1 0 SIG0 Register Table 27 - Bootload RAM Signature Register (SIG) 45 Zarlink Semiconductor Inc. Package Code c Zarlink Semiconductor 2004. All rights reserved. ISSUE ACN DATE APPRD. Previous package codes For more information about all Zarlink products visit our Web Site at www.zarlink.com Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request. Purchase of Zarlink’s I2C components conveys a license under the Philips I2C Patent rights to use these components in an I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink, ZL, the Zarlink Semiconductor logo and the Legerity logo and combinations thereof, VoiceEdge, VoicePort, SLAC, ISLIC, ISLAC and VoicePath are trademarks of Zarlink Semiconductor Inc. TECHNICAL DOCUMENTATION - NOT FOR RESALE