www.yageo.com RoHS Compliant ISO-9001:2000 CERTIFIED ELECTROLYTIC CAPACITORS INDEX aluminum electrolytic capacitors MINIATURE aluminum electrolytic capacitors 26S5 [ For Super Miniature ] 1,000hrs. at105°C 28SS [ For Super Miniature ] 1,000hrs. at105°C 30SK [ For General ] 2,000hrs. at 85°C 35SE-K [ For General ] 1,000hrs. at105°C 40SH [ For General ] 2,000hrs. at105°C 44SG [ Electronic Ballast ] 5,000hrs. at105°C 47SP [ Miniature and Long Life ] 10,000hrs. at105°C 49SB [ For Low Leakage Current ] 1,000hrs. at105°C 53SN [ For Non Polar ] 1,000hrs. at105°C 56SR [ For Horizontal Deflection ] 1,000hrs. at105°C 58SC [ For Low Impedance and Low ESR Suitable for Output of Motherboard ] 3,000hrs. at105°C 62SJ [ Low Impedance and High Ripple Series ] 67SQ [ For Adapter and Power Supply Applications Series ] 70SY [ For Low Impedance and Low ESR Suitable for Output of Motherboard ] 76SZ [ Ultra Low ESR ] 1,000~5,000hrs. at105°C 2,000hrs. at105°C 3,000~6,000hrs. at105°C 2,000hrs. at105°C Large can aluminum electrolytic capacitors 78LH [ For 85°C, 2000 Hours Miniature ] 2,000hrs. at 85°C 87LG [ For 105°C, 2000 Hours General ] 2,000hrs. at105°C 95LV [ For 105°C, 3000 Hours Long Life ] 3,000hrs. at105°C surface mount aluminum electrolytic capacitors 102CA [ For General ] 2,000hrs. at 85°C 105CB [ For General ] 1,000hrs. at105°C 108CE [ For Long Life ] 2,000hrs. at105°C 111CZ [ For Low Impedance ] 1,000hrs. at105°C 115CD [ For Ultra Low Impedance ] 2,000hrs. at105°C CONDUCTIVE POLYMER SOLID CAPACITORS 118CP [ For Ultra Low ESR & High Ripple Current ] 2,000hrs. at105°C 120CG [ For Low ESR & High Ripple Current ] 2,000hrs. at105°C SCREW TYPE ALUMINUM ELECTROLYTIC CAPACITORS 122 NP [ For General ] 2,000hrs. at 85°C 127 NM [ For Wide Temperature ] 2,000hrs. at105°C 132 NF [ Long Life for Inverter ] 5,000hrs. at 85°C 134 NH [ High Temperature, Long Life for Inverter ] 5,000hrs. at105°C 139 NG [ For Low Voltage, Large Capacity ] 2,000hrs. at 85°C 4 PRECAUTIONS IN USING ALUMINUM ELECTROLYTIC CAPACITORS Please note the following recommendations when using capacitors: 1. When using Electrolytic capacitors on DC applications, polarization is required as well as the confirmation of the polarity of the course. 9. Do not apply excessive force to the lead wires or terminals. It may break the components or disconnect the internal elements on the board. (For strength of terminals, please refer to JIS C5102 and C5141.) Otherwise, the circuit life may be shortened or the capacitor may be damaged by the insertion on reverse polarity. 10. Keep the clearance between the vent of the capacitor and the case of Use non-polar capacitors on those circuits with occasionally reverse the appliance. Do not block the operation of the vent, unless otherwise polarity or unknown polarity. Also note that do not use electrolytic described on the catalogues or product specifications. The narrower capacitors for AC applications. clearance may adversely affect the vent operation and result in the capacitor explosion. 2. Do not apply a voltage exceeding the capacitor rated voltage, that will cause the capacitor be damaged by increased leakage current. Case of the application 3. Use the electrolytic capacitor at current value under the permissible ripple range. Critical space between top (cap) and case Clearance 4. Use the electrolytic capacitors according to the specified operation Board temperature range. Using at room temperature will ensure a longer life. 5. The electrolytic capacitor is not suitable for circuits which are charged and discharged repeatedly. If used in circuits which are charged and discharged repeatedly, the capacitance value may drop or the capacitor Case diameter Clearance 6.3ø to 16ø mm 2 mm minimum 18ø to 35ø mm 3 mm minimum 40ø mm & up 5 mm minimum Fig.1-1 may be damaged. Please consult our engineering department for assistance in these applications. 6. When capacitors have been left unused for a long time, use them only Attention after due voltage treatments. Long storage time may raise capacitor's • The description in this catalogue is subject to change without prior leakage current level. In such cases, be sure to provide the necessary notice for product improvement. Therefore, please confirm the voltage treatment before use. specification before ordering products. • The general characteristics, reliability data, etc., described in this 7. Be careful of the temperature and time conditions when soldering. Adverse effects may happen on the electrical characteristics and insulation sleeve of electrolytic capacitors may occur in case the soldering temperature is too high or dipping time too long. For small-size electrolytic capacitors, proper dipping shall be executed at temperature lower than 260°C for less than 10 seconds. 8. Clean circuit boards after soldering. Halogenated hydrocarbon cleaning solvents are not recommended to clean capacitors with exposed end seals. If halogenated solvent is required, order and use capacitors in Epoxy-coated end seals. catalogue should not be construed as guaranteed values; they are merely standard values. • Before using the products, please read the notes in this catalogue carefully for proper use. 5 Technical Concepts The Material and Structure of Electrolytic Capacitors 4. Winding: The stitching or cold welding of cut anode and cathode foils Electrolytic Capacitor is a simple module. It simply contains an insulator and tab terminal, and wrap the electrolytic paper in between the anode between relative conductors in an electrode. The major internal raw and cathode, then fix the end with glue or sticky tape, and attached material contains an element constructed by an separator paper wrap leads is called the capacitor "element". around the anode foil and cathode foil, which is then impregnated with the 5. Impregnation: The process of eliminating the water from the elements electrolyte, inserted into an aluminum case and sealed. by pressurizes or vacuum in order to soak the element with the electrolyte is called Impregnation. The elements fully filled with Rivent Lead Wire Rubber Seal Anode Foil Separator Paper Cathode Foil Aluminum Case Vinyl Sleeve Sleeve Aluminum Case Element Terminal Washer Lead Tab Anode Foil Separator Paper Cathode Foil Separator Paper Bottom Plate Safe Device Safe Device ( For Dia, >10mm ) electrolyte is then centrifuged to remove excess electrolyte. 6. Assembly: The elements are sealed with rubber to stop the leakage of electrolyte then put into a sleeve to form the final product. 7. Aging: The purpose of aging is to repair the oxide layer damage by recharging and electrolyte. Rubber Seal Separator Paper Anode Foil Cathode Foil Aluminum Case Isolator Terminals Fig.1-2 Production Processes 1. Etching: The process to increase surface area of aluminum foil by using chemical erosion or chemical corrosion method is called Etching. Normally chemical corrosion method uses the ripple current of electrolyte, combination of the liquid and temperature to determine the size, shape, and quantity of the dense network of microscopic channels on the aluminum foil surface. 2. Forming: The production process of the anode aluminum foil of electrolytic capacitors is by anodic oxidation of the etched aluminum foil. The production of the cathode aluminum foil sometimes involves oxidation in special purposes. This anodic oxidation process is called Forming. Boric acid or organic acid is used for high voltage forming and phosphoric acid or ammonium adipose is used for low voltage forming in order to obtain stable natural oxide layer of Al2O3. 3. Slitting: The cutting of the aluminum foil and separator paper according to the required length. 6 The Function of Electrolytic Capacitors The electrolytic capacitors could be widely used in appliance (ie. TV, radio, For AC Voltage: audio equipment, washing machine and air conditioner…etc.), computer 1. For Power Improving: Connect the end loading of layout transporting & equipment (motherboard, image device & the peripherals such as the electrolytic capacitor for power improving. printer, drawing device, scanner... etc.), communication equipment, estate equipment, measuring instrument and also the industrial instrument, air plane, firebomb, satellite…etc. as a piloting equipment. 2. For Wave Filter: Prevention of external interference in SCR circuit, use the LC wave filter circuit to inhibit or erase the interference. * According to the inflict electric wave & using purpose, it basically with some classified purposes as below: 3. For Phase Across: Phase change of the inductive electromotor (motor) with single phase. DC Voltage: 1. For Momentary High Voltage: For using to the impulse generator such as the shock wave resistance test of the heavy electric machine. 2. For High Electric Current: For using to the welding machine, X-Ray facility, copy machine and discharge-processing device. 3. For DC High Voltage: The electrolytic capacitor and rectifier composing, a special DC high voltage been happened after charged, for using to the power of electronic microscope and accelerator. 4. For Integration & Memory: For either memory circuit or compare circuit inside the calculator. The DC Voltage that with Alternate Ingredient: 1. For Wave Filter: Combination with the chip resistor & inductor as a internet, to be passed by DC current or some frequency to closure or decline some other frequency. 2. For Bypass: A parallel track that outside from the circuit element, the IC (integrated circuit) has been rapidly developed in these years and thus a miniaturization or chip of electrolytic capacitors for bypass was conduced. 3. For Coupling: Combination of the electrolytic capacitor, chip resistor and inductor and thus coupling together. 4. For Arising of Toothed Wave: Composing of RC charge/discharge circuit through the electrolytic capacitor as well as the resistor to generate a toothed wave to be created. 5. For Reverse (Change) of Circuit: The equipment for changing the AC voltage to DC voltage. 7 Basic Electrical Characteristics Capacitance (ESC) Dissipation Factor (tan ) The capacitive component of the equivalent series circuit (equivalent series The dissipation factor is the ratio between the active and the reactive capacitance ESC) is determined by applying an alternate voltage of 0.5V at power for a sinusoidal waveform voltage. It can be considered as a a frequency of 120 Hz. measurement of the gap between an actual and an ideal capacitor. L R C C = Capacitance (F) R = Equivalent series resistance (Ω) L = Equivalent series inductance (H) reactive Fig.1-3 Simplified equivalent circuit diagram of an electrolytic capacitor ideal D.F. = tan δ x 100 (%) = ω CR x 100 (%) = 2 π f CR x 100 (%) actual • Temperature Dependence of the Capacitance The capacitance of an electrolytic capacitor depends on the temperature. With decreasing temperature, the viscosity of the electrolyte increases and reduces its conductivity which leads to the where: R = Equivalent Series Resistance C = Equivalent Series Capacitance W = 2π f active Fig. 1-6 The tan is measured with the same set up as for the series capacitance ESC capacitance decrease. Furthermore temperature drifts cause armature dilatation and therefore capacitance changes (up to 20%, depending evident on electrolytic capacitors than other types. DF on the series considered, from 0 to 80 °C). This phenomenon is more CAP Temperature(°C) Fig. 1-7 Dissipation Factor vs. Temperature Temperature(°C) Frequency Dependence of the Capacitance The effective capacitance value is derived from the impedance curve, as long as the impedance is still in the range where the capacitance component is dominant. C= 1 2πfZ Frequency Fig. 1-8 Dissipation Factor vs. Frequency C = Capacitance (F) f = Frequency (Hz) Z = Impedance (Ω) CAP • DF Fig. 1-4 Capacitance Change vs.Temperature Frequency Fig. 1-5 Capacitance Change vs. Frequency 8 Basic Electrical Characteristics Equivalent Series Resistance (ESR) Co= Aluminum oxide capacitance (surface and thickness of the dielectric). The equivalent series resistance is the resistive component of the equivalent Re = Resistance of electrolyte and paper mixture (other resistances not series circuit. The ESR value depends on frequency and temperature and is depending on the frequency are not considered: tabs, plates, and so related to the tan δ by the following equation: on). Ce= Electrolyte soaked paper capacitance. L = Inductive reactance of the capacitor winding and terminals. ESR = ESR = tanδ = ESC = f = tanδ 2πfESC Equivalent Series Resistance (Ω) Dissipation Factor Equivalent Series Capacitance (F) Frequency (Hz) The impedance of an electrolytic capacitor changes depending on the frequency and the temperature. The impedance as a function of frequency (sinusoidal waveform) under a The tolerance limits of the rated capacitance must be taken into account certain temperature can be represented as follows: when calculating this value. Z (ohm) 1000 100 ESR 1/ω Ce B 10 Re ωL A 1 Temperature(°C) 1/ω Ce 0.1 Fig. 1-9 ESR Change vs. Temperature 0.1 1 10 100 1000 Fig. 1-12 10000 F (KHz) The resistance of the electrolyte decreases strongly with increasing 1. Capacitive reactance predominates at low frequencies temperature. 2. With increasing frequency, the capacitive reactance Xc=1/ω Co decreases until it reaches the order of magnitude of the electrolyte ESR resistance Re (A) 3. At even higher frequencies, the resistance of the electrolyte predominates: Z = Re (A-B) Frequency Fig. 1-10 ESR Change vs. Frequency 4. When the capacitor's resonance frequency is reached (ω0), capacitive and cancel each other 1/ω conducive reactance mutually cancel each other 1/ω Ce = ωL, ω0 = SQR (1/LCe) (C) Impedance (Z) The impedance of an electrolytic capacitor results from below circuit formed by the following individual equivalent series components. 5. Above this frequency, the inductive reactance of the winding and its terminals (Xl = Z = ωL) becomes effective and leads to an increase in Co Re Ce impedance. Generally speaking it can be estimated that Ce≒0.01 Co L Fig. 1-11 9 Basic Electrical Characteristics The impedance as a function of frequency (sinusoidal waveform) for I different temperature values can be represented as follows (typical values): Z (ohm) 1000 10 µF/450Vdc 100 VR -40°C 10 VS VF V Fig. 1-14 20°C Where: 85°C 1 VF = Forming Voltage If this level is exceeded, a large quantity of heat and gas will be generated 0.1 0.1 1 10 100 1000 Fig. 1-13 10000 F (KHz) and the capacitor could be damaged. VR = Rated Voltage This level represents the top of the linear part of the curve. VS = Surge Voltage Re is the most temperature dependant component of electrolytic It lies between VR and VF: the capacitor can be applied with Vs for short capacitor equivalent circuit. The electrolyte resistivity will decrease when periods only. the temperature rises. In order to obtain a low impedance value in all temperature range. Re must be as little as possible, but too low Re values means a very aggressive electrolyte and a shorter life of the electrolytic capacitor at the high temperatures. A compromise must be reached. Leakage Current (L.C.) Due to the aluminum oxide layer that serves as a dielectric, a small current will continue to flow even after a DC voltage has been applied for long periods. This current is called leakage current. A high leakage current flows after applying a voltage to the capacitor and then decreases in few minutes (e.g. after a prolonged storage without any applied voltage). In the course of the continuous operation, the leakage current will decrease and reach an almost constant value. After a voltage free storage the oxide layer may deteriorate, especially at high temperature. Since there are no currents to transport oxygen ions to the anode, the oxide layer is not regenerated. The result is that a higher than normal leakage current will flow when a voltage is applied after prolonged storage. As the oxide layer is regenerated in use, the leakage current will gradually decrease to its normal level. The relationship between the leakage current and the voltage applied at constant temperature can be shown schematically as follows. 10 Reliability Bathtub Curve 1. Initial Failure Period Aluminum electrolytic capacitors failure rates are shown by the following Deficient Capacitors include any products before dispatch that may bathtub curve. have some deficiency caused by the design, production process or use in inappropriate environments. 2 1 3 2. Random Failure Period The capacitors have a low defect ratio in the period after it has been Failure Rate stabilized. 3. Wear Out Failure Period The performance of capacitors will decrease with an increase in usage period. The malfunction rate may vary due to the structural design. Time Fig. 1-15 Bathtub Curve Table-1 Failure Modes and Causes Failure Modes Short Circuit Primary Factors Internal Causes Mismanaged Production Short Circuit Between Electrodes Burred Foil / Metal Particle Dielectrical Break of Oxide Layer Local Deficiency in Oxide Layer Dielectrical Break of Separator Open Circuit Mishandled Application Mechanical Stress Disconnection of Terminal Construction Mechanical Stress Poor Terminal Connection Poor Connection Deterioration with Time Electrolyte Vaporization Excessive Thermal Stress tanδ (ESR) Increase Anode Foil Capacitance Drop Excessive Operating Voltage Leakage Current Increase Open Vent Electrolyte Leakage Deterioration of Oxide Layer Corrosion Intermal Pressure Rise Poor Sealing Electrochemical Reaction Capacitance Drop Less Electrolyte Cathode Foil Capacitance Drop Unavoidable Factors in Normal Service Reverse Voltage Excessive Ripple Current Contamination by Chloride Excessive Charge-Discharge Duty Chloride Contamination by Assembly Board Cleaning Poor Sealing 11 CIRCUIT DESIGN Environmental and Mounting Conditions where Tc is the surface temperature (ºC) of capacitor case Tx is ditto. Please make sure the environmental and mounting conditions are compliant Kc is transfer coefficient between element and case of capacitor from with their specifications in this catalog. table below : Operating Temperature, Equivalent Series Resistance(ESR), Ripple Current Dia ≤8ø 10ø and Load Life Kc 12.5ø 13ø 1.10 1.15 1.20 16ø 18ø 22ø 25ø 30ø 35ø 1.20 1.25 1.30 1.35 1.40 1.50 1.65 MTTF(Mean-Time-To-Failure) means the useful life at room temperature 25ºC 1. Load Life (L0) 3. The Formula of Equivalent Series Resistance (ESR) If the capacitor's max. operating temperature is at 105 ºC (85ºC), then The operating frequency of ESR, DF, f & C must be the same, usually after applying capacitor's rated voltage (WV) for L0 hours at 10ºC are 120 Hz. (85ºC), the capacitor shall meet the requirements in detail specification. ESR = DF / 2πf C…………(2) where L0 is called "load life" or "useful life (life time) at 105 ºC (85ºC)". Where DF = Dissipation Factor (tanδ) Lx = L0 x 2 (To-Tx) / 10 x K - ΔTx / 5 where ΔTx = ΔT0 x ( Ix / I0 )2 f = Operating Frequency (Hz) C= Capacitance (F) Ix > I0, K = 4; Ix ≤ I0, K = 2 4. Estimation of Life Considering the Ripple Current 2. Ripple Life (Lr) The ripple current affects the life of a capacitor because the internal If the capacitor's max. operating temperature is at 105 ºC (85ºC), then loss (ESR) generates heat. The heat can be calculated by: after applying capacitor's rated voltage (WV) with the ripple current for P = I2 R------- (3) Lr hours at 105 ºC (85ºC), the capacitor shall meet the requirements Where I = Ripple current (Arms.) in detail specification. where Lr is called "ripple life" or "useful ripple life R= ESR (Ω) (ripple lifetime) at 105 ºC (85ºC)". Lx = Lr x 2 (To - Tx) / 10 x K (ΔTo - ΔTx) / 5 where ΔTx = ΔT0 x ( Ix / I0 )2 Ix > I0, K = 4; Ix ≤ I0, K = 2 5. Estimation of the Capacitor Temperature Increase ΔT = I2R / AH------ (4) Where ΔT= Temperature increase in the capacitor core (degree) The (ripple) life expectancy at a lower temperature than the specified I = Ripple current (Arms) maximum temperature may be estimated by the following equation, R= ESR (Ω) but this expectancy formula does not apply for ambient below +40ºC. A = Surface area of the capacitor (cm2) L0 : Expected life period (hrs) at maximum operating temperature H = Radiation coefficient (Approx.1.5~2.0´10-3 W / cm2) allowed Lr : Expected ripple life period (hrs) at maximum operating temperature allowed Lx : Expected life period (hrs) at actual operating temperature The values of ΔT varies depending on the capacitor types and operating conditions. The usage is generally desirable if ΔT remains less than 5º. The measuring point for temperature increase due to ripple current is shown below T0 : Maximum operating temperature (ºC) allowed Tx : Actual operating ambient temperature (ºC) Ix : Actual applied ripple current (mA/rms) at operating frequency f0 (Hz) Measuring Point I0 : Rated maximum permissible ripple current IR (mA/rms) x frequency multiplier (Cf) at f0 (Hz) Ripple Current calculation: no need Temperature Multiplying Factor Ix Should be 80% equal or more of I0 T0 : Maximum temperature rise (ºC) for applying I0 (mA/rms) = 5 Tc : Temperature rise (ºC) of capacitor case for applying Ix (mA/rms) Tx : Temperature rise (ºC) of capacitor element for applying Ix (mA/ rms)= KcΔTc = Kc (Tc - Tx) Fig.1-16 12 CIRCUIT DESIGN Conditions of Use Recommended Design Considerations Aluminum Electrolytic Capacitors must not be used under the following When designing a circuit board, please be noted to the following points: conditions: 1. Make the hole spacing of the PC board match the lead space for the 1. When capacitors expose to high humidity or humidity condensation capacitor. situation such as water or saltwater spray, oil spray, steam. 2. There should not be any circuit pattern or circuit wire above the 2. When capacitors are exposed to toxic gases such as hydrogen sulfide, capacitors. sulfurous acid, nitrous acid, chlorine, ammonium... etc. 3. It is suggested to make a gas release hole when the capacitor's vent is 3. When capacitors are exposed to ozone, ultraviolet rays and radiation. 4. When severe vibration or shock occurs and exceeds the conditions specified in the catalog or datasheet. placed toward the PC board. 4. Do not install screw terminal capacitor upside down. When place a screw terminal capacitor in a horizontal mount, the positive terminal must be in the upper position. 5. Aluminum Electrolytic Capacitors should be electrically isolated from the following circumstances • Aluminum case, cathode lead wire, and anode lead wire. 5. Do not locate any wiring or circuit patterns directly above the capacitor's vent. • Auxiliary terminals of snap-in type, anode terminal, and outward terminal. CAUTION FOR MOUNTING Caution Before Assembly 4. Be careful not to deform the capacitor during installation. 1. When the capacitors that are removed from PC board for the measuring electrical characteristics purpose at a periodical inspection, can be recycled to the same position. However, when mounting and 5. The snap-in type of capacitors should be mounted firmly on the PC board without a gap between the capacitor body and the surface of PC board. applying electricity in unit, the capacitors cannot be recycled afterwards. 6. Avoid excessive force when clinching lead wire during auto-insertion process. 2. Aluminum Electrolytic Capacitors may accumulate charge during storage. In this case, discharge through a 1KΩ resistor before use. 7. Avoid excessive shock to capacitors by automatic insertion machine, during mounting, parts inspection or centering operations. 3. Leakage current of Aluminum Electrolytic Capacitors may be increased during long storage time. In this case, the capacitors should be subjected to voltage treatment through a 1KΩ resistor before use. 8. Please utilize supporting material such as strap or adhesive to mount capacitors to PC board when it is anticipated that vibration or shock is applied. In the Assembly Process Soldering 1. Please confirm ratings before installing capacitors on the PC board. 1. All YAGEO's cp wires of electrolytic capacitors are lead free. (Pb). 2. Please confirm polarity before installing capacitors on the PC board. 2. Soldering conditions (temperatures, times) should be within the specified conditions which are described in the catalog or specification sheets. 3. Do not make capacitors drop on the floor or use a dropped capacitor. 13 CAUTION FOR MOUNTING 3. If it is necessary that the leads must be formed due to a mismatch Peak Temperature T°C t sec (max) of the lead space to hole space on the board, bend the lead prior to 250 4. If soldering capacitor has to be withdrawn from the PW board by soldering iron, the capacitor should be removed after the solder has melted completely in order to avoid stress to the capacitor or lead wires. 5. Soldering iron should never touch the capacitor's body. Temperature at lead of capacitor (°C) soldering without applying too much stress to the capacitor. 200 150 60 sec (max) Preheat (160~190°C) 100 120 Sec (max) 90 sec (max) 50 Flow Soldering Time (sec) Fig. 1-18 Lead Free Type Reflow Soldering Condition 1. Do not dip capacitor's body into melted solder. 2. Din of flow soldering for the capacitors should be limited at 260ºC, 10 seconds. SIZE Temperature t sec (max.) ø4 ~ ø5 (4V ~ 50V) 250 10 260 5 250 5 3. Flux should not be adhered to capacitor's body but only to its terminals. ø6.3 ~ ø10 (4V ~ 50V) 4. Other devices which are mounted near capacitors should not touch the capacitors. Cleaning 1. Satisfied characteristic of JIS C 5101. Reflow Soldering Condition 1. For reflow, use a thermal condition system such as infrared radiation or hot blast. Vapor heat transfer systems are not recommended. 2. Aluminum Electrolytic Capacitors may be damaged by corrosion that is caused by any halogenated hydrocarbon solvents Ex: HCH(Cl)2). All of 2. Observe proper soldering conditions (i.e. temperature, time, etc.) our products are non-solvent-proof, cleaning recommendation are as followed. Application: An type and rating 3. Do not exceed the specified limits. Cleaning agents: pine Alpha ST-100S, Clean Through 750H/750L/710M, Sanelek B-12, Aqua Cleaner 210SEP, Techno Care FRW14~17, Iso- 4. Repeated reflowing : propyl Alcohol * Avoid reflowing twice if possible. * If repeated reflowing is unavoidable, contact Yageo after measuring the first and the second reflow profiles and reflow interval at your side. Peak Temperature 230°C 250 Cleaning conditions: Total cleaning time shall be within 5 minutes by immersion, ultrasonic or other method. (Temperature of the cleaning agent shall be 60ºC or lower). After cleaning, capacitors should be dried using hot air for minimum of 10 minutes along with the PC board. Temperature at lead of capacitor (°C) 20 sec (max) 200 Hot air temperature should be below the maximum operating temperature of the capacitor. Insufficient drying after water rinse may cause appearance 150 100 60 sec (max) problems, sleeve may shrink, or the bottom-plate may bulge, etc… Preheat (140~180°C) 150 Sec (max) 100 sec (max) 50 Please inform Yageo in advance the solvent name and conditions for your PWB Cleaning. Time (sec) Fig. 1-17 Reflow Soldering Condition 14 EMERGENCY ACTION 1. If you see smoke due to the operation of safety vent, turn off the main switch or pull out the plug. 2. Do not put your face near the safety vent as gas which is over 100ºC will be emitted when the safety vent operates. If the gas has entered your eyes, please rinse your eyes immediately with water. If you breathe in the gas, immediately wash out your mouth and throat with water. Do not ingest electrolyte. If your skin is exposed to electrolyte, please wash it immediately with soap and water. STORAGE CONDITION 1. Aluminum electrolytic capacitors should not be stored in high temperatures or high level of humidity. The suitable storage condition is 5 ºC ~ 35 ºC and less than 75% in relative humidity. 2. Aluminum electrolytic capacitors should not be stored in damp conditions such as water, saltwater spray or oil spray. 3. Do not store aluminum electrolytic capacitors in an environment full of hazardous gases (hydrogen sulfide, sulfurous acid, nitrous acid, chlorine, ammonium, etc.) 4. Aluminum electrolytic capacitors should not be stored under exposure to ozone, ultraviolet rays or radiation. 5. If a capacitor has been stored more than a year under normal temperature (shorter time if higher temperature) and it shows increased leakage current, then a treatment by voltage application is recommended. ENVIRONMENT – RELATED SUBSTANCES All YAGEO capacitors comply to RoHS requirements (Restriction of Hazardous Substances) where Chromium VI (Cr+6), Cadmium (Cd), Mercury (Hg), Lead (pb), polybrominated biphenyls (PBBs) and Polybrominated bipheny1/dipheny1 ethers (PBBEs / PBDEs) have not detected (lower than MDL(Method Detection Limit)) per SGS certification test report. DISPOSAL Please dispose capacitors in either of the following ways: 1. Incinerate the capacitors after making a hole on the capacitor body. 2. A capacitor disposal specialist in burying procedure handling is recommended. 15 THE CHARACTERISITICS OF ENDURANCE TEST Capacitance Change (%) 15.00 10.00 5.00 0.00 -5.00 -10.00 0 500 1000 1500 2000 Time (h) 0 500 1000 1500 2000 Time (h) 50.00 DF (%) 40.00 30.00 20.00 10.00 0.00 Leakage Current (µA) 8.00 6.00 4.00 2.00 A (100µF/25V) 0.00 -2.00 B (4.7µF/350V) C (10µF/160V) 0 500 1000 1500 2000 Time (h) 16 radial type ordering code SK 063 M 0220 A 5 S - 1019 Series Name Case Size 2 Digits 4 Digits 0407= 04 x 07 0511= 05 x 11 1019= 10 x 19 1625= 16 x 25 1836= 18 x 36 2240= 22 x 40 Voltage Capacitance Rubber 3 Digits 006 = 6.3 V 010 = 10 V 100 = 100 V 450 = 450 V 4 Digits 0R10= 0.1µF 1R00 = 1µF 0010 = 10µF 0100 = 100µF 1000 = 1000µF 10K0 = 10000µF 100K = 100000µF 1 Digit F = Flat Rubber S = Rubber Stand-off Tolerance Pitch 1 Digit K =±10% M =±20% Y =±10% ~ +50% W =-5% ~ +20% V =-10% ~ +20% Others = Special design 1 Digit 1 = 1.5mm 2 = 2.0mm 3 = 3.5mm 5 = 5.0mm 7 = 7.5mm H= 2.6mm P =10.0mm Z= 2.5mm 1 Digit A =Taping B =Bulk C =Lead Cut / Bulk (Shape A) F =Form & Lead Cut / Bulk (Shape B) K =Form & Lead Cut & Crimp / Bulk (Shape C) L =Lead Cut & Crimp / Bulk (Shape D) J =Lead Cut & Crimp / Bulk (Shape E) 1 Digit - = No Lead Cut / Standard 1 = Lead Cut Length 5.0 ± 0.2 mm 2 = Lead Cut Length 4.5 ± 0.2 mm 3 = Lead Cut Length 4.2 ± 0.2 mm 4 = Lead Cut Length 4.7 ± 0.2 mm 5 = Lead Cut Length 8.0 ± 0.2 mm 7 = Lead Cut Length15.0 ± 0.5 mm 8 = Lead Cut Length10.0 ± 0.2 mm 9 = Lead Cut Length 3.5 ± 0.3 mm J = Lead Cut Length 3.1 ± 0.2 mm L = Lead Cut Length 3.3 ± 0.2 mm M = Lead Cut Length 3.7 ± 0.2 mm Q= Lead Cut Length 7.0 ± 0.2 mm V = Lead Cut Length 2.8 ± 0.2 mm W= Lead Cut Length 4.0 ± 0.2 mm 17 Snap in type ordering code LG 160 M 0820 B P F - 2250 Series Name Case Size 2 Digits 4 Digits 2250=22 x 50 2540=25 x 40 3030=30 x 30 3525=35 x 25 Voltage Capacitance Rubber & Terminal 3 Digits 006 = 6.3 V 010 = 10 V 100 = 100 V 450 = 450 V 4 Digits 0R10= 0.1µF 1R00 = 1µF 0010 = 10µF 0100 = 100µF 1000 = 1000µF 10K0 = 10000µF 100K = 100000µF F = Flat Rubber & 2 pins 3 = Flat Rubber & 3 pins 4 = Flat Rubber & 4 pins 5 = Flat Rubber & 5 pins Tolerance Pitch 1 Digit K =±10% M =±20% Y =±10% ~ +50% W =-5% ~ +20% V =-10% ~ +20% 1 Digit P =10.0mm 1 Digit B =Bulk 1 Digit - =Terminal Length 4 =Terminal Length 5.8 mm 4.0 mm 18 SMD type ordering code CA 063 M 0220 R E B - 0405 Series Name Size 2 Digits 4 Digits 0405=4.0 x 5.4 0505=5.0 x 5.4 0605=6.3 x 5.4 0607=6.3 x 7.7 0806=8.0 x 6.5 0810=8.0 x 10.5 1010=10.0 x 10.5 Voltage Capacitance Size 3 Digits 006 = 6.3 V 010 = 10 V 050 = 50 V 100 = 100 V 4 Digits 0R10= 0.1µF 1R00 = 1µF 0010 = 10µF 0100 = 100µF 1000 = 1000µF 1 Digit B = 4.0 x 5.4 C = 5.0 x 5.4 D = 6.3 x 5.4 E = 8.0 x 6.5 F = 8.0 x 10.5 G = 10.0 x 10.5 H = 6.3 x 7.7 Tolerance Life 1 Digit K =±10% M =±20% Y =±10% ~ +50% W =-5% ~ +20% V =-10% ~ +20% 1 Digit E = 2000 Hours S = 1000 Hours Package 1 Digit R = Reel 19 package information RADIAL TYPE D x L: mm BULK TAPING LEAD CUTTING BAG/PCS INNER BOX CARTON INNER BOX CARTON BAG/PCS INNER BOX CARTON 04 x 05 1000 10,000 20,000 2,500 25,000 1000 15,000 30,000 05 x 05 1000 10,000 20,000 2,000 20,000 1000 15,000 30,000 06 x 05 1000 10,000 20,000 2,000 20,000 1000 15,000 30,000 04 x 07 1000 10,000 20,000 2,500 25,000 1000 15,000 30,000 05 x 07 1000 10,000 20,000 2,000 20,000 1000 15,000 30,000 06 x 07 1000 10,000 20,000 2,000 20,000 1000 15,000 30,000 05 x 11 500 10,000 20,000 2,000 20,000 500 15,000 30,000 06 x 11 500 10,000 20,000 2,000 20,000 500 15,000 30,000 08 x 11 500 6,000 12,000 1,000 10,000 500 8,000 16,000 08 x 15 500 5,000 10,000 1,000 10,000 500 5,000 10,000 08 x 20 200 4,000 8,000 1,000 10,000 200 4,000 8,000 10 x 12 200 4,000 8,000 700 7,000 200 4,000 8,000 10 x 15 200 3,000 6,000 700 7,000 200 4,000 8,000 10 x 16 200 3,000 6,000 700 7,000 200 4,000 8,000 10 x 19 200 2,400 4,800 700 7,000 200 3,000 6,000 10 x 25 200 2,400 4,800 700 7,000 200 2,400 4,800 10 x 27 200 2,000 4,000 200 2,000 4,000 10 x 30 200 2,000 4,000 200 2,000 4,000 12 x 20 200 2,000 4,000 500 5,000 200 2,000 4,000 12 x 25 200 1,800 3,600 500 5,000 200 1,800 3,600 12 x 30 200 1,200 2,400 200 1,600 3,200 12 x 35 200 1,000 2,000 500 3,000 12 x 40 200 1,000 2,000 500 3,000 13 x 20 200 1,800 3,600 500 5,000 200 1,800 3,600 13 x 25 200 1,400 2,800 500 5,000 200 1,400 2,800 13 x 30 200 1,200 2,400 500 3,000 13 x 40 200 1,000 2,000 500 3,000 16 x 25 200 1,000 2,000 500 4,000 16 x 32 200 1,000 1,600 500 3,000 16 x 36 200 600 1,200 500 3,000 16 x 40 200 600 1,200 500 3,000 18 x 20 200 800 1,600 1,000 2,000 18 x 25 200 800 1,600 500 2,000 18 x 32 100 500 1,000 500 2,000 18 x 36 100 500 1,000 500 2,000 18 x 40 100 300 1,000 500 2,000 22 x 40 100 300 600 400 800 300 3,000 200 SNAP-IN TYPE INNER BOX CARTON SMD TYPE REEL CARTON 22 x 25 ~ 45 400 800 4x5 2,000 20,000 25 x 25 ~ 50 200 800 5x5 1,000 10,000 6x5 1,000 10,000 30 x 25 ~ 35 200 800 6x7 1,000 10,000 8x6 1,000 10,000 8 x 10 500 3,000 10 x 10 500 3,000 30 x 40 ~ 50 200 800 35 x 30 ~ 50 200 800 20 Diagram of Taping Dimensions Unit: mm Fig. 1 Fig. 4 P2 P2 P P 1.0 1.0 P1 1.0Max. F A D A D P1 1.0Max. F H H0 H H0 W2 W1 L W W t t W1 L W2 W0 W0 D0 Mounting Tape P0 D0 Mounting tape P0 Adhesive Tape d Fig. 2 Adhesive tape d Fig. 5 P2 P 1.0 P 1.0 P2 D A P1 F H F H W2 W W t t W1 L L W2 W1 P1 A D W0 W0 D0 Mounting Tape P0 P0 I D0 Mounting Tape Adhesive Tape d Adhesive Tape d Fig. 3 Fig. 6 P2 P P2 P 1.0 P1 F H A P1 D A D 1.0 H F I P0 W W W0 t W1 L W2 t W1 L W2 W0 D0 Mounting Tape d Adhesive Tape I P0 D0 Mounting Tape d Adhesive Tape 21 Specifications Information ITEM TOLERANCE ph = 2.5 L 5~7 ≤7 >7 straight lead type L L 5~7 ≤7 4ø >7 5ø ≤7 >7 6ø ≤7 >7 5~7 ≤7 >7 5ø ≤7 8ø 4ø 13 8.0 22.0 8.0 13 8.0 0.5 0.5 0.5 0.5 0.5 >7 >7 12~25 15~25 +0.5, -0 4ø A Max. 8.0 13 8.0 13 8.0 d ±0.05 0.45 0.5 0.45 0.5 0.5 P ±1.0 12.7 12.7 12.7 15.0 P0 ±0.3 12.7 12.7 12.7 15.0 P1 ±0.7 5.1 3.85 5.6 P2 ±1.3 6.35 6.35 6.35 F +0.6, -0.2 2.5 5.0 1.5 W +1.0, -0.5 18.0 18.0 18.0 W0 ±0.5 12.0 12.0 12.0 W1 ±0.5 9.0 9.0 9.0 W2 Max. 3.0 3.0 3.0 H ±0.75 18.5 18.5 18.5 H0 ±0.5 16.0 16.0 - I Max. - - - D0 ±0.2 4.0 4.0 4.0 t ±0.2 0.7 0.7 0.7 L Max. 11.0 11.0 11.0 4 1 2 0.45 5.35 6ø ≤7 D Fig. 5ø Unit: mm formed lead type 5.1 8ø 10ø 13 8.0 22.0 27.0 0.5 0.5 0.5 4.6 12ø 0.6 15~25 12.5ø 13ø 16ø 18ø 0.8 5.0 30.0 3.75 7.5 2.0 2.5 3.5 5.0 7.5 ± 0.8 1.0 3, 6 5 22 Diagram of lead Cutting and Forming Shape (A) Unit: mm Shape (B) Shape (C) 5ø, 6ø 1.12 8ø 1.32 E±0.1 d F±0.5 F±0.5 H2±0.1 d F±0.5 d 2.5 Max. 2.5 Max. H±0.5 H±0.5 Shape (D) H1±0.5 Shape (E) 10ø-13ø 1.32 16ø-22ø 1.50 E±0.1 d d F1±0.5 F±0.5 H2±0.5 H2±0.1 2.5max F±0.5 H1±0.5 H1±0.5 Specifications Information NO. A B C Unit: mm CUTTING & FORMING METHODS Dø 4ø 5ø 6ø 8ø 10ø 12ø 13ø 16ø 18ø 22ø Lead Cut Only F 1.5 2.0 2.5 3.5 5.0 5.0 5.0 7.5 7.5 10 H 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 d 0.45 0.5 0.5 0.5 0.6 0.6 0.6 0.8 0.8 0.8 F 5.0 5.0 5.0 5.0 H 5.0 5.0 5.0 5.0 d 0.45 0.5 0.5 0.5 Lead Cut, F 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 Crimp and Form H1 5.0 4.2 5.0 4.2 4.0 5.0 4.2 4.0 5.0 4.2 4.0 5.0 5.0 7.5 7.5 7.5 Lead Cut and Form H2 2.5 2.0 2.5 2.0 2.0 2.5 2.0 2.0 2.5 2.0 2.0 d D E Lead Cut and Crimp Lead Cut Form and Crimp 0.45 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 F 5.0 5.0 H1 2.5 5.0 4.2 4.0 5.0 4.2 4.0 5.0 4.2 4.0 5.0 4.2 4.0 5.0 4.2 4.0 5.0 4.2 4.0 H2 3.5 2.5 2.0 2.0 2.5 2.0 2.0 2.5 2.0 2.0 2.5 2.0 2.0 2.5 2.0 2.0 2.5 2.0 2.0 d 0.5 0.6 F 5.0 5.0 5.0 5.0 F1 1.2 1.2 1.2 1.2 H1 4.0 4.0 4.0 4.0 H2 1.8 1.8 1.8 1.8 d 0.5 0.5 0.5 0.45 0.6 0.6 0.8 0.8 0.8 10 23 CARRIER TAPE DIMENSION 0.4±0.05 Unit: mm ø1.5±0.1 4±0.1 1.75±0.1 F B t2±0.15 W±0.3 A P1±0.1 CASE SIZE (øD mm) W A B P1 F t2 B ø4 12.0 4.7 4.7 8.0 5.5 5.8 C ø5 12.0 5.7 5.7 12.0 5.5 5.8 D ø6.3 x 5.4 16.0 7.0 7.0 12.0 7.5 5.8 E ø8 x 6.5 16.0 8.7 8.7 12.0 7.5 6.8 F ø8 x 10.5 24.0 8.7 8.7 16.0 11.5 11.0 G ø10 x 10.5 24.0 10.7 10.7 16.0 11.5 11.0 H ø6.3 x 7.7 16.0 7.0 7.0 12.0 7.5 8.0 REEL DIMENSION 2±0.5 ø21±0.8 80± 1 W2 380± 2 380±2 ø13±0.5 SIZE CODE B C D E F G H W1±1 14 14 18 18 26 26 18 W2±1 20 20 24 24 32 32 24 W1 24 DETAILS OF CARRIER TAPE SPECIFICATION (1) Details of carrier tape Carrier tape a. Last reeling empty part of carrier tape shall be more than 10 cm b. Leader part of seal tape shall be more than 20 cm Empty part Seal tape Adhesive tape Lead part Fixing tape c. First reeling empty part of carrier tape shall be more than 10 cm d. Adhesive tape fixing the end of the leader part shall be Seal tape approx 10 cm 0.5 Max (2) Deviation between carrier tape and seal tape a. Deviation between carrier tape and seal tape shall be less Carrier tape than 0.5 mm b. Seal tape shall not cover on the feeding holes more than Carrier tape 0.75 mm 0.75 Max Seal tape ADHESION TEST Reasonable pulling strength: 0.1~0.7N, Pulling speed: 300mm / min Reasonable pulling strength: 0.1~0.7N Pulling speed: 300mm / min Pull Scale Seal tape θ: apporx 10° Carrier tape θ 25 PACKING STYLE (1) Carrier tape shall be reeled inside. (seal tape shall be outside) (2) End of the tape shall be inside to the reel physically as shown in the (1) below figure and leader part of seal tape shall not be attached. Reel PACKAGING QUANTITY SIZE CODE DxL ONE REEL (PCS) TOTAL QUANTITY (PCS) B 4 x 5.4 2,000 20,000 C 5 x 5.4 1,000 10,000 D 6.3 x 5.4 1,000 10,000 E 8 x 6.5 1,000 10,000 F 8 x 10.5 500 4,000 G 10 x 10.5 500 4,000 H 6.3 x 7.7 1,000 10,000 Yageo corporation ELECTROLYTIC CAPACITORS Miniature Aluminum Electrolytic Capacitors S5 [ For Super Miniature ] 105°C Single-Ended Lead, 5.0mm Height Type Aluminum Electrolytic Capacitors electrical characteristics Operating Temperature Range : -40 ~ +105°C Rated Voltage Range : 4 ~ 50V Rate Capacitance Range : 0.1 ~ 470µF Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C description DC Leakage Current (µA) : I = 0.01CV (µA) or 3µA Whichever is greater. (After Rated Voltage Applied for 2 Minutes ) The S5 series are smaller than SS series. Dissipation Factor : at 120 Hz, 20°C W V (V): 4 6.3 10 D.F (%) : 35 24 20 This type is designed for saving space and high density insertion. Applications : VTR, Camera, Car Audio, Miniaudio and Other Industrial and Commercial Applications MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient FREQUENCY (Hz) 120 300 1K 10K~100K 0.1~47µF 1.00 1.20 1.30 1.50 100~330µF 1.00 1.10 1.15 1.20 16 17 25 15 35 12 50 10 Endurance : After apply rated voltage for 1000 hours at 105°C, the capacitor shall meet following requirements. (a) Capacitance Change : Within 20% of Initial Value (b) Dissipation Factor : 200% or Less of Initial Specified Value (c) Leakage Current : Initial Specified Value or Less Shelf Life : After leaving capacitors under load at 105°C for 500 hours. (a) Capacitance Change : Within 20% of Initial Value (b) Dissipation Factor : 200% or Less of Initial Specified Value (c) Leakage Current : 200% or Less of Initial Specified Value Temperature Coefficient TEMPERATURE (°C) 65 85 105 FACTOR 1.40 1.20 1.00 diagram of dimensions Dimensions: mm Rubber Stand-off Vinyl Sleeve (P.V.C) Rubber End Seal Rubber End Seal Vinyl Sleeve (P.V.C) F±0.5 F±0.5 L 15Min. 5Min. D±0.5 L L ≤ 16 L + 1.5Max. L > 16 L + 2Max. Dø = 8 & 10 L + 2.5Max. 0.4Max. 15Min. 5Min. D±0.5 Dø < 20 Dø + 0.5 Dø ≥ 20 Dø + 1 Dø F dø 4.0 1.5 0.45 5.0 2.0 6.3 2.5 8.0 3.5 27 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 4 (5) SIZE 6.3 (8) RIPPLE SIZE 10 (13) 16 (20) 25 (32) 35 (44) 50 (63) RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE 0.1 4x5 1 0.22 4x5 2 0.33 4x5 3 0.47 4x5 4 1.0 4x5 9 2.2 4x5 13 3.3 4x5 17 4x5 17 5x5 20 4.7 4x5 10 4x5 18 4x5 20 4x5 20 23 15 22 33 47 4x5 4x5 5x5 20 25 30 4x5 4x5 28 33 4x5 35 5x5 45 68 100 6.3 x 5 50 5x5 55 6.3 x 5 70 220 6.3 x 5 70 6.3 x 5 90 330 8x5 110 8x5 115 8x5 100 470 Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz 5x5 33 4x5 29 5x5 37 4x5 16 4x5 20 5x5 27 6.3 x 5 42 4x5 34 5x5 44 5x5 45 5x5 41 6.3 x 5 49 6.3 x 5 53 5x5 46 5x5 54 5x5 55 6.3 x 5 58 6.3 x 5 65 6.3 x 5 85 8x5 90 6.3 x 5 54 6.3 x 5 80 4x5 18 5x5 30 6.3 x 5 33 6.3 x 5 48 6.3 x 5 55 Yageo corporation ELECTROLYTIC CAPACITORS Miniature Aluminum Electrolytic Capacitors SS [ For Super Miniature ] 105°C Single-Ended Lead Aluminum Electrolytic Capacitors electrical characteristics Operating Temperature Range : -40 ~ +105°C Rated Voltage Range : 4 ~ 63V Rated Capacitance Range : 0.1 ~ 470µF Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C description DC Leakage Current (µA) : I = 0.01CV (μA) or 3μA Whichever is greater. ( After Rated Voltage Applied for 2 Minutes ) This type is designed to meet the demand or equipments for greatly reduced size and thickness, such as: portable micro computer, disk driver, small calculator and audio equipement. Dissipation Factor W V (V): 4 D.F. (%) : 35 Application : Portable Micro Computer, Disk Driver, Small Calculator and Audio Endurance : After Applying Rated Voltage for 1000 Hours at 105°C (a) Capacitance Change : Within 20% of Initial Value (b) Dissipation Factor : 200% or Less of Initial Specified Value (c) Leakage Current : Initial Specified Value or Less MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient FREQUENCY (Hz) 50 120 300 1K 10K 0.1~47µF 0.75 1.00 1.20 1.30 1.50 100~330µF 0.75 1.00 1.10 1.15 1.20 6.3 24 10 20 16 17 25 15 35 12 50 10 63 8 Shelf Life : After leaving capacitors under load at 105°C for 500 hours. (a) Capacitance Change : Within 20% of Initial Value (b) Dissipation Factor : 200% or Less of Initial Specified Value (c) Leakage Current : 200% or Less of Initial Specified Value Temperature Coefficient TEMPERATURE (°C) 65 85 105 FACTOR 1.70 1.30 1.00 diagram of dimensions Dimensions: mm Rubber Stand-off Rubber End Seal Vinyl Sleeve (P.V.C) Rubber End Seal Vinyl Sleeve (P.V.C) 15Min. 5Min. F±0.5 F±0.5 L D±0.5 L L ≤ 16 L + 1.5Max. L > 16 L + 2Max. Dø = 8 & 10 L + 2.5Max. 0.4Max. 15Min. 5Min. D±0.5 Dø < 20 Dø + 0.5 Dø ≥ 20 Dø + 1 Dø F dø 4.0 1.5 0.45 5.0 2.0 6.3 2.5 8.0 3.5 0.5 29 case size & permissible ripple current of standard products CAP. (μF) D x L: mm Rated Voltage W V (SURGE VOLTAGE W V) 4 (5) 6.3 (8) 10 (13) 16 (20) 25 (32) 35 (44) 50 (63) 63 (79) SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE 0.1 4x7 1 4x7 1 0.22 4x7 2 4x7 2 0.33 4x7 3 4x7 4 0.47 4x7 5 4x7 6 0.68 4x7 6 4x7 10 4x7 13 1.0 4x7 10 2.2 4x7 7 4x7 19 4x7 21 3.3 4x7 13 4x7 24 4x7 26 4.7 4x7 19 26 10 4x7 22 4x7 29 4x7 24 4x7 24 4x7 29 4x7 5x7 24 5x7 31 6.3 x 7 33 4x7 33 4x7 34 4x7 37 5x7 5x7 35 5x7 36 5x7 45 6.3 x 7 50 6.3 x 7 35 22 4x7 37 6.3 x 7 45 4x7 31 4x7 36 4x7 43 5x7 48 5x7 38 5x7 44 5x7 51 6.3 x 7 57 6.3 x 7 65 6.3 x 7 53 33 47 4x7 4x7 30 35 5x7 42 4x7 39 4x7 50 5x7 5x7 47 5x7 57 6.3 x 7 65 75 5x7 4x7 46 4x7 50 5x7 5x7 55 5x7 60 6.3 x 7 77 55 67 6.3 x 7 79 6.3 x 7 60 68 100 5x7 55 5x7 75 6.3 x 7 90 5x7 85 6.3 x 7 100 150 220 5x7 84 5x7 94 6.3 x 7 110 6.3 x 7 120 6.3 x 7 95 6.3 x 7 130 330 8x7 140 470 8x7 130 8x9 150 Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz 6.3 x 7 135 8x9 165 6.3 x 7 110 8x7 140 8x9 140 8x9 155 8x9 170 6.3 x 7 120 8x7 120 6.3 x 7 70 6.3 x 7 81 6.3 x 7 80 42 Yageo corporation ELECTROLYTIC CAPACITORS Miniature Aluminum Electrolytic Capacitors SK [ For General ] 85°C Single-Ended Lead Aluminum Electrolytic Capacitors Electrical Characteristics Operating Temperature Range : -40 ~ +85°C / -25 ~ +85°C Rated Voltage Range : 6.3 ~ 100V / 160 ~ 450V Rated Capacitance Range : 0.1 ~ 22000µF / 0.47 ~ 470µF Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C description Lower-cost capacitors expressly intended for high density printed circuit board. Very High Volumetric Efficiency Ideally suited for general-purpose applications, decoupling by pass, and filtering circuit in entertainment electronics. Feature High CV Product with Moderate Cost MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient FREQUENCY (Hz) 120 300 1K 10K~100K 6.3~100V Below~68µF 1.00 1.20 1.30 1.50 6.3~100V 100~680µF 1.00 1.10 1.15 1.20 6.3~110V 1000~22000µF 1.00 1.05 1.10 1.15 160~450V Below~220µF 1.00 1.25 1.40 1.40 160~450V 220µF Above 1.00 1.10 1.13 1.13 DC Leakage Current (µA) : I = 0.01CV (μA) or 3μA / I = 0.03CV (μA) + 10μA Whichever is greater. (After Rated Voltage Applied for 2 Minutes ) Dissipation Factor W V (V): 6.3 10 16 25 35 50 63 100 160 ~ 250 350 ~ 450 D.F (%) : 22 19 16 14 12 10 9 8 15 20 For capacitor whose capacitance exceeds 1000µF. The value of DF(%) is increased by 2% for every addition of 1000µF. Endurance : After applying rated voltage for 2000 hours at 85°C, the capacitors shall meet following requirements. (a) Capacitance Change : Within 20% of Initial Value (b) Dissipation Factor : 200% or Less of Initial Specified Value (c) Leakage Current : Initial Specified Value or Less Shelf Life : After placed at 85°C without voltage applied for 1000 hours the capacitors shall meet following requirements. (a) Capacitance Change : Within 20% of Initial Value (b) Dissipation Factor : 200% or Less of Initial Specified Value (c) Leakage Current : Initial Specified Value or Less Temperature Coefficient TEMPERATURE (°C) 50 70 85 FACTOR 1.30 1.15 1.00 diagram of dimensions Dimensions: mm Rubber Stand-off Vinyl Sleeve (P.V.C) Rubber End Seal Vinyl Sleeve (P.V.C) Rubber End Seal F±0.5 F±0.5 L 15Min. 5Min. D±0.5 L L ≤ 16 L + 1.5Max. L > 16 L + 2Max. Dø = 8 & 10 L + 2.5Max. 0.4Max. 15Min. 5Min. D±0.5 Dø < 20 Dø + 0.5 Dø ≥ 20 Dø + 1 Dø 4.0 5.0 6.3 8.0 10.0 12.0 13.0 16.0 18.0 22.0 F 1.5 2.0 2.5 3.5 5.0 dø 0.45 0.5 7.5 0.8 10.0 0.6 31 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 6.3 (8) SIZE 10 (13) 16 (20) 25 (32) 35 (44) 50 (63) 63 (79) RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE 0.1 5 x 11 1 0.22 5 x 11 2 0.33 5 x 11 3 5 x 11 3 0.47 5 x 11 5 5 x 11 5 0.68 5 x 11 7 5 x 11 10 5 x 11 10 5 x 11 23 5 x 11 29 5 x 11 35 5 x 11 40 5 x 11 40 5 x 11 45 5 x 11 50 5 x 11 65 5 x 11 70 5 x 11 80 5 x 11 100 5 x 11 95 6.3 x 11 115 1.0 5 x 11 10 2.2 5 x 11 20 5 x 11 10 3.3 4.7 5 x 11 20 5 x 11 25 5 x 11 30 5 x 11 35 6.8 10 5 x 11 35 15 22 33 47 5 x 11 5 x 11 5 x 11 35 55 75 5 x 11 5 x 11 5 x 11 55 80 95 68 100 5 x 11 130 5 x 11 180 150 220 5 x 11 200 6.3 x 11 240 330 470 5 x 11 40 5 x 11 50 5 x 11 75 5 x 11 5 x 11 110 130 5 x 11 5 x 11 5 x 11 50 90 115 5 x 11 5 x 11 5 x 11 60 95 120 5 x 11 105 6.3 x 11 130 6.3 x 11 125 8 x 11 140 5 x 11 135 5 x 11 120 6.3 x 11 140 6.3 x 11 160 6.3 x 11 135 6.3 x 11 140 8 x 11 150 8 x 11 190 5 x 11 150 6.3 x 11 145 8 x 11 180 5 x 11 165 6.3 x 11 160 6.3 x 11 185 8 x 11 230 10 x 12.5 300 6.3 x 11 185 8 x 11 200 8 x 11 230 10 x 12 250 10 x 15 300 6.3 x 11 205 410 5 x 11 215 6.3 x 11 260 8 x 11 290 8 x 11 290 10 x 12 380 10 x 15 6.3 x 11 250 8 x 11 320 10 x 12 340 10 x 12 370 10 x 15 440 10 x 19.5 490 10 x 15 370 490 10 x 19.5 540 6.3 x 11 260 6.3 x 11 265 6.3 x 11 290 8 x 11 315 8 x 15 386 10 x 15 8 x 11 8 x 11 330 8 x 11 360 8 x 15 380 10 x 12 420 10 x 19.5 580 10 x 12 420 10 x 15 490 13 x 13 430 300 6.3 x 11 330 6.3 x 11 320 8 x 11 400 8 x 15 420 10 x 15 8 x 11 8 x 11 400 10 x 12 470 10 x 12 460 10 x 19.5 510 10 x 15 540 13 x 20 380 Note: 1. Ripple Current: (mA/rms) 85°C, 120Hz 640 13 x 20 680 10 x 19.5 610 13 x 20 755 13 x 20 13 x 25 880 16 x 25 880 530 760 32 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) 680 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 6.3 (8) SIZE 10 (13) 16 (20) 25 (32) 35 (44) 50 (63) 63 (79) RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE 8 x 11 410 10 x 12 460 10 x 12 510 10 x 19.5 762 13 x 20 705 13 x 25 965 10 x 15 565 10 x 15 13 x 25 780 16 x 25 1085 540 10 x 19.5 595 1000 1200 8 x 11 460 10 x 12 580 10 x 12 530 10 x 19.5 760 10 x 19.5 770 13 x 25 1100 16 x 25 1310 10 x 12 580 10 x 15 630 10 x 15 630 12 x 16 760 13 x 20 950 16 x 25 1350 16 x 32 1550 10 x 19.5 790 13 x 16 760 13 x 25 1100 13 x 20 950 16 x 25 1240 10 x 12 620 1500 2200 3300 4700 6800 10000 15000 22000 10 x 15 754 10 x 19.5 700 13 x 16 10 x 19.5 840 10 x 19.5 880 10 x 19.5 925 13 x 20 1100 16 x 32 1660 18 x 36 2000 18 x 40 2200 13 x 20 13 x 20 13 x 20 1100 13 x 25 1300 16 x 25 1600 16 x 36 1850 22 x 35 2200 13 x 25 1350 16 x 25 1550 16 x 32 1800 18 x 36 2090 22 x 40 2200 18 x 20 1550 1660 16 x 36 1970 18 x 36 2170 22 x 40 2500 18 x 36 2220 18 x 40 2400 1050 1100 825 10 x 19.5 1000 13 x 20 1250 13 x 20 1200 16 x 25 13 x 20 13 x 25 1400 13 x 25 1400 16 x 32 16 x 25 1700 1250 13 x 20 1300 13 x 25 1500 13 x 40 1882 16 x 32 1950 16 x 36 2136 18 x 50 2350 13 x 25 1437 16 x 25 1800 16 x 25 1800 18 x 36 2360 18 x 36 2400 22 x 35 2240 16 x 25 1700 16 x 32 2100 22 x 40 2500 16 x 25 1900 16 x 25 1900 16 x 32 1980 16 x 32 2150 16 x 36 2200 18 x 36 2500 18 x 36 2700 22 x 40 2800 22 x 40 3200 16 x 25 1900 16 x 36 2225 16 x 32 2250 18 x 36 2500 16 x 36 2500 18 x 36 2950 22 x 40 3150 18 x 36 2880 18 x 40 3650 22 x 40 3700 22 x 40 3800 Note: 1. Ripple Current: (mA/rms) 85°C, 120Hz 18 x 36 2550 18 x 40 2200 22 x 40 2600 33 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 100 (125) 160 (200) 200 (250) 250 (300) 350 (400) 400 (450) 450 (500) SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE 0.22 5 x 11 5 0.47 5 x 11 10 5 x 11 12 5 x 11 14 5 x 11 14 5 x 11 14 6.3 x 11 14 6.3 x 11 14 1.0 5 x 11 21 5 x 11 17 5 x 11 19 5 x 11 17 6.3 x 11 19 6.3 x 11 16 6.3 x 11 15 6.3 x 11 17 6.3 x 11 19 8 x 11 19 8 x 11 19 6.3 x 11 26 10 x 12 33 2.2 3.3 4.7 6.8 10 5 x 11 5 x 11 5 x 11 5 x 11 5 x 11 30 45 50 8 x 11 22 6.3 x 11 24 8 x 11 33 8 x 11 26 8 x 11 27 8 x 11 30 10 x 12 33 10 x 12 33 10 x 12 40 10 x 15 42 10 x 15 45 10 x 15 50 6.3 x 11 30 6.3 x 11 30 8 x 11 30 8 x 11 33 8 x 11 35 8 x 11 37 10 x 12 38 10 x 12 39 6.3 x 11 32 8 x 11 36 8 x 11 36 8 x 11 36 8 x 11 40 10 x 12 45 10 x 12 45 10 x 12 39 10 x 15 45 55 65 6.3 x 11 75 15 6.3 x 11 8 x 11 40 10 x 15 10 x 12 50 10 x 19.5 50 50 10 x 12 57 10 x 15 70 10 x 15 70 10 x 15 50 13 x 20 60 10 x 12 65 10 x 15 70 10 x 19.5 70 13 x 20 70 10 x 19.5 56 13 x 25 75 10 x 15 65 13 x 20 93 13 x 20 93 10 x 19.5 75 33 47 6.3 x 11 105 10 x 15 8 x 11 10 x 19.5 110 130 8 x 11 140 10 x 12 170 50 8 x 11 13 x 20 22 10 x 19.5 50 110 10 x 19.5 150 10 x 15 120 10 x 19.5 160 70 10 x 19.5 90 90 10 x 19.5 130 13 x 20 130 13 x 20 100 16 x 20 100 13 x 25 110 16 x 25 110 16 x 25 130 16 x 32 130 13 x 20 140 13 x 25 170 13 x 25 140 16 x 25 145 13 x 25 160 16 x 25 170 16 x 20 145 16 x 32 160 16 x 25 170 16 x 36 180 16 x 25 180 18 x 36 200 18 x 40 230 10 x 12 190 12 x 16 145 13 x 20 160 13 x 20 180 16 x 15 230 12 x 25 180 13 x 25 190 13 x 25 210 16 x 32 220 13 x 20 180 16 x 25 210 16 x 36 220 18 x 25 236 18 x 32 265 22 x 40 370 68 10 x 15 280 100 10 x 19.5 400 13 x 25 250 16 x 25 300 120 Note: 1. Ripple Current: (mA/rms) 85°C, 120Hz 13 x 25 230 16 x 25 330 16 x 25 375 16 x 25 440 16 x 32 310 16 x 25 220 16 x 36 320 16 x 36 320 18 x 36 360 18 x 36 360 34 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 100 (125) 160 (200) 200 (250) 250 (300) 350 (400) 400 (450) 450 (500) SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE 150 13 x 20 500 220 13 x 25 710 330 470 18 x 25 485 18 x 36 540 16 x 36 510 18 x 32 540 18 x 40 600 18 x 36 600 18 x 36 540 16 x 40 710 16 x 25 860 18 x 40 600 16 x 45 750 18 x 32 685 18 x 36 725 18 x 40 800 18 x 40 750 22 x 35 1000 16 x 25 1100 16 x 32 1100 680 16 x 36 1260 1000 18 x 40 1350 22 x 35 1680 22 x 40 2300 2200 450 720 1100 410 16 x 32 13 x 25 13 x 40 18 x 40 22 x 40 Note: 1. Ripple Current: (mA/rms) 85°C, 120Hz 900 18 x 40 800 Yageo corporation ELECTROLYTIC CAPACITORS SE-K [ For General ] Miniature Aluminum Electrolytic Capacitors 105°C Single-Ended Lead Aluminum Electrolytic Capacitors Rated Voltage up to 450V electrical characteristics Operating Temperature Range : -40 ~ +105°C / -40 ~ +105°C / 25 ~ +105°C Rated Voltage Range : 6.3 ~ 100V / 160 ~ 250V / 350 ~ 450V Rated Capacitance Range : 0.47 ~ 15000μF / 0.47 ~ 470μF / 0.47 ~ 150μF Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C Leakage Current (µA) : I = 0.01CV (μA) + 3μA / 0.03CV (μA) + 10μA Whichever is greater. (After Rated Voltage Applied for 2 Minutes) description Dissipation Factor W V (V): 6.3 D.F. (%) : 26 Lower-cost capacitors expressly intended for high density printed circuit board. 10 22 16 18 25 16 35 14 50 12 63~100 10 160 ~ 250 15 350 ~ 450 20 Endurance : After applying rated voltage for 1000 hours at 105°C. The capacitors shall meet the following requirements. (a) Capacitance Change : Within 20% of Initial Value (b) Dissipation Factor : 200% or Less of Initial Specified Value (c) Leakage Current : Initial Specified Value or Less Shelf Life : After leaving capacitors under no load at 105°C for 500 hours, the capacitors shall meet the same requirement as Endurance. Very High Volumetric Efficiency. Ideally suited for general-purpose applications, coupling, decoupling, by pass, and filtering circuit in entertainment electronics. Feature High CV Product with Moderate Cost. MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient FREQUENCY (Hz) 120 300 1K 10K~100K 6.3~100V Below~68µF 1.00 1.20 1.30 1.45 6.3~100V 100~680µF 1.00 1.10 1.15 1.25 6.3~110V 1000~22000µF 1.00 1.05 1.10 1.15 160~450V ALL Cap(µF) 1.00 1.05 1.10 1.50 diagram of dimensions Dø F dø 5.0 2.0 0.5 6.3 2.5 8.0 3.5 10.0 5.0 0.6 Dimensions: mm Rubber Stand-off Rubber End Seal Vinyl Sleeve (P.V.C) 13.0 L 7.5 0.8 10.0 0.8 (1.0) 18.0 22.0 L ≤ 16 L + 1.5Max. l > 16 L + 2Max. Dø = 8 & 10 L + 2.5Max. 0.4Max. 15Min. 5Min. F±0.5 F±0.5 12.0 16.0 Rubber End Seal Vinyl Sleeve (P.V.C) D±0.5 Dø < 20 Dø + 0.5 Dø ≥ 20 Dø + 1 L 15Min. 5Min. D±0.5 36 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 6.3 (8) SIZE 10 (13) 16 (20) 25 (32) 35 (44) 50 (63) 63 (79) RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE 0.47 5 x 11 7 5 x 11 8 0.68 5 x 11 7 1.0 5 x 11 12 5 x 11 13 2.2 5 x 11 18 5 x 11 20 3.3 5 x 11 25 5 x 11 27 4.7 5 x 11 20 5 x 11 25 5 x 11 30 5 x 11 34 6.8 5 x 11 25 5 x 11 30 5 x 11 32 5 x 11 37 10 5 x 11 25 5 x 11 30 5 x 11 40 5 x 11 50 5 x 11 55 15 5 x 11 40 5 x 11 45 5 x 11 50 5 x 11 60 5 x 11 65 5 x 11 55 5 x 11 60 5 x 11 65 5 x 11 75 5 x 11 75 6.3 x 11 90 6.3 x 11 110 8 x 11 120 22 5 x 11 33 47 5 x 11 5 x 11 60 5 x 11 45 60 75 5 x 11 70 5 x 11 85 6.3 x 11 97 5 x 11 5 x 11 75 90 5 x 11 85 6.3 x 11 105 5 x 11 95 6.3 x 11 100 6.3 x 11 128 6.3 x 11 115 8 x 11 125 8 x 11 155 68 5 x 11 75 5 x 11 80 5 x 11 100 6.3 x 11 125 8 x 11 130 8 x 11 159 10 x 12 198 100 5 x 11 100 5 x 11 110 5 x 11 110 6.3 x 11 145 6.3 x 11 150 8 x 11 160 8 x 15 230 6.3 x 11 135 6.3 x 11 135 8 x 11 160 8 x 11 190 10 x 12 210 10 x 12 260 5 x 11 110 8 x 11 180 8 x 11 200 10 x 12 240 10 x 12 289 10 x 15 330 6.3 x 11 130 5 x 11 150 6.3 x 11 180 8 x 11 200 8 x 11 230 10 x 12 340 10 x 15 400 6.3 x 11 180 8 x 11 235 10 x 12 250 8 x 15 280 10 x 15 400 10 x 19.5 460 10 x 12 315 450 10 x 19.5 520 150 220 5 x 11 5 x 11 120 140 6.3 x 11 165 270 330 470 8 x 11 210 6.3 x 11 160 6.3 x 11 205 8 x 11 8 x 11 255 200 8 x 11 285 8 x 11 265 8 x 15 345 10 x 15 8 x 15 320 8 x 20 420 10 x 19.5 535 13 x 20 650 10 x 12 355 10 x 12 380 10 x 15 440 415 10 x 19.5 580 13 x 20 700 13 x 20 13 x 25 800 6.3 x 11 220 6.3 x 11 245 8 x 11 310 8 x 15 365 10 x 15 8 x 11 8 x 11 305 8 x 15 360 10 x 12 400 10 x 19.5 490 10 x 12 395 10 x 15 470 13 x 20 580 10 x 30 600 280 560 Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz 730 37 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) 680 1000 1500 2200 3300 4700 6800 10000 15000 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 6.3 (8) SIZE 10 (13) 16 (20) 25 (32) 35 (44) 50 (63) 63 (79) RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE 8 x 11 255 8 x 11 335 10 x 12 455 10 x 15 540 10 x 19.5 600 10 x 12 320 8 x 15 385 10 x 15 530 10 x 19.5 650 13 x 20 730 10 x 12 420 13 x 25 860 13 x 25 840 16 x 25 1000 8 x 11 370 8 x 11 390 8 x 20 600 10 x 19.5 680 13 x 20 850 13 x 25 930 16 x 25 1020 10 x 12 470 8 x 15 450 10 x 15 590 13 x 20 855 13 x 25 995 16 x 25 1110 16 x 32 1200 10 x 12 490 10 x 19.5 700 10 x 15 570 13 x 25 1020 13 x 25 935 16 x 32 1350 16 x 32 1300 16 x 25 1110 16 x 36 1450 18 x 36 1455 10 x 15 600 10 x 19.5 750 10 x 19.5 680 13 x 20 860 10 x 19.5 740 10 x 19.5 800 10 x 25 895 13 x 25 1030 16 x 25 1230 16 x 36 1360 13 x 20 13 x 20 12 x 25 1040 16 x 25 1230 16 x 32 1450 18 x 36 1530 13 x 20 990 13 x 25 1150 930 1010 10 x 19.5 880 10 x 25 950 13 x 25 1140 13 x 25 1035 16 x 36 1470 18 x 36 1540 13 x 20 10 x 30 1090 16 x 25 1350 16 x 25 1230 18 x 36 1660 18 x 40 1700 13 x 20 1050 16 x 32 1450 13 x 25 1220 22 x 35 1900 1100 13 x 25 1100 13 x 25 1190 16 x 25 1330 16 x 32 1420 18 x 36 1580 16 x 25 1320 16 x 25 1410 16 x 32 1560 18 x 36 1690 18 x 40 1750 13 x 25 1250 16 x 25 1370 16 x 32 1400 18 x 36 1850 18 x 40 1600 16 x 25 1490 16 x 32 1610 16 x 36 1590 22 x 40 1885 16 x 40 1670 18 x 32 1600 18 x 36 1790 18 x 36 2100 16 x 25 1560 16 x 36 1760 16 x 32 1830 18 x 36 1980 18 x 36 2280 18 x 40 1960 Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz 38 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 100 (125) 160 (200) 200 (250) 250 (300) 350 (400) 400 (450) 450 (500) SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE 0.47 5 x 11 10 5 x 11 12 5 x 11 14 5 x 11 14 5 x 11 14 6.3 x 11 14 6.3 x 11 14 1.0 5 x 11 15 5 x 11 17 5 x 11 19 6.3 x 11 19 6.3 x 11 20 6.3 x 11 16 8 x 11 20 8 x 11 20 8 x 11 28 10 x 12 35 10 x 12 35 10 x 15 54 10 x 15 60 2.2 3.3 4.7 6.8 10 5 x 11 5 x 11 5 x 11 5 x 11 5 x 11 22 29 37 46 55 6.3 x 11 65 15 22 33 47 8 x 11 8 x 11 82 115 8 x 11 120 10 x 12 160 10 x 12 180 10 x 15 210 6.3 x 11 25 6.3 x 11 22 6.3 x 11 23 8 x 11 28 8 x 11 29 8 x 11 35 6.3 x 11 30 6.3 x 11 32 8 x 11 33 8 x 11 37 8 x 11 38 8 x 11 36 8 x 11 40 10 x 12 42 10 x 12 47 10 x 12 50 6.3 x 11 34 8 x 11 40 8 x 11 41 8 x 11 37 8 x 11 40 8 x 11 43 10 x 12 50 10 x 12 52 10 x 12 47 8 x 15 45 10 x 15 55 10 x 12 49 10 x 15 57 10 x 15 60 10 x 12 54 10 x 12 60 8 x 15 57 10 x 12 62 88 8 x 11 56 10 x 12 69 10 x 15 10 x 12 70 10 x 15 80 10 x 19.5 90 10 x 15 90 8 x 20 125 10 x 15 130 10 x 19.5 180 13 x 20 270 Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz 10 x 15 10 x 15 110 140 10 x 19.5 190 13 x 20 240 13 x 25 290 10 x 15 120 10 x 19.5 155 13 x 20 170 13 x 25 200 13 x 25 330 10 x 15 65 10 x 19.5 80 10 x 19.5 72 10 x 15 95 10 x 19.5 140 13 x 20 13 x 25 16 x 25 165 220 340 10 x 15 65 10 x 19.5 70 10 x 19.5 77 13 x 20 85 13 x 20 13 x 25 100 16 x 25 160 97 10 x 19.5 100 13 x 20 125 13 x 25 150 13 x 20 150 13 x 25 125 13 x 25 175 16 x 25 150 16 x 32 180 13 x 25 190 16 x 25 190 16 x 20 195 16 x 36 240 16 x 25 230 16 x 25 280 16 x 36 300 16 x 32 315 18 x 40 360 16 x 36 350 18 x 20 275 18 x 25 300 39 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 100 (125) 160 (200) 200 (250) 250 (300) 350 (400) 400 (450) 450 (500) SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE 68 100 10 x 15 241 10 x 19.5 385 13 x 25 300 13 x 25 330 13 x 25 330 13 x 25 340 16 x 25 400 16 x 25 410 16 x 25 16 x 32 350 430 16 x 32 18 x 36 370 460 120 150 13 x 25 414 16 x 32 435 16 x 32 400 16 x 36 450 18 x 40 460 180 220 330 470 13 x 25 590 16 x 32 550 18 x 32 520 16 x 36 620 18 x 36 580 18 x 40 650 13 x 25 600 18 x 36 770 18 x 36 705 16 x 25 720 18 x 40 850 18 x 40 780 22 x 40 920 16 x 25 740 16 x 32 875 680 16 x 36 1200 1000 18 x 40 1340 22 x 40 1500 22 x 40 980 Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz 22 x 40 680 22 x 40 480 16 x 32 320 18 x 32 305 16 x 36 335 22 x 40 400 18 x 25 305 18 x 36 380 16 x 36 425 22 x 40 450 18 x 32 430 18 x 36 480 18 x 36 480 22 x 40 450 18 x 40 350 Yageo corporation ELECTROLYTIC CAPACITORS Miniature Aluminum Electrolytic Capacitors SH [ For General ] 105°C Single-Ended Lead Aluminum Electrolytic Capacitors for the Rated Voltage up to 450V electrical characteristics Operating Temperature Range : -40 ~ +105°C / -25 ~ +105°C Rated Voltage Range : 6.3 ~ 100V / 160 ~ 450V Rated Capacitance Range : 0.47 ~ 15000µF / 0.47 ~ 470μF Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C description Leakage Current (µA) : I = 0.01CV (μA) + 3μA / 0.03CV (μA) + 10μA (After Rated Voltage Applied for 2 Minutes ) Long life for 2000 hours at 105°C, ideally suited for high quality and high reliability applications. Dissipation Factor W V (V) : 6.3 10 16 25 35 50 63 ~ 100 160 ~ 250 350 ~ 450 D.F (%) : 26 22 18 16 14 12 10 15 20 For capacitor whose capacitance excceds 1000µF. The value of DF(%) is increased by 2% for every addition of 1000µF. Feature High CV Product MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient FREQUENCY (Hz) 120 300 1K 10K~100K 6.3~100V Below~68µF 1.00 1.30 1.57 2.00 6.3~100V 100~470µF 1.00 1.23 1.34 1.50 6.3~100V 471~22000µF 1.00 1.10 1.13 1.15 160~450V ALL Cap(µF) 1.00 1.25 1.40 1.60 Temperature Coefficient TEMPERATURE (°C) 65 85 105 FACTOR 1.70 1.40 1.00 Low Temperature Stability Impedance Ratio (Max.) W V (V) : 6.3 10 Impedance : Z - 25°C / Z + 25°C 4 3 Z - 40°C / Z + 20°C 8 6 16 2 4 25 ~ 100 2 3 160 ~ 250 4 6 350 ~ 450 4 8 Endurance : After applying rated voltage for 2000 hours, at 105°C, the capacitors shall meet following requirements. (a) Capacitance Change : Within 20% of Initial Value (b) Dissipation Factor : 200% or Less of Initial Specified Value (c) Leakage Current : Initial Specified Value or Less Shelf Life: After leaving capacitors under no load at 105°C for 1000 hours, the capacitors shall meet the same requirement as Endurance. diagram of dimensions Dimensions: mm Rubber Stand-off Rubber End Seal Vinyl Sleeve (P.V.C) Coated case P±0.5 F±0.5 L 15Min. 5Min. D±0.5 L+a L ≤ 16 L + 1.5Max. L > 16 L + 2Max. Dø = 8 & 10 L + 2.5Max. 15Min. 4Min. Dø F dø 5.0 2.0 0.5 6.3 2.5 8.0 3.5 10.0 5.0 0.6 7.5 0.8 12.0 D±0.5 Dø < 20 Dø + 0.5 Dø ≥ 20 Dø + 1 13.0 16.0 18.0 22.0 10.0 41 case size & permissible ripple current of standard products CAP. (μF) D x L: mm Rated Voltage W V (SURGE VOLTAGE W V) 6.3 (8) SIZE RIPPLE 10 (13) SIZE RIPPLE 10 16 (20) SIZE RIPPLE 25 (32) SIZE RIPPLE 35 (44) SIZE RIPPLE 5 x 11 44 5 x 11 43 5 x 11 44 5 x 11 50 15 22 33 5 x 11 60 5 x 11 65 5 x 11 70 5 x 11 75 5 x 11 85 47 5 x 11 75 5 x 11 85 5 x 11 90 6.3 x 11 115 68 5 x 11 80 5 x 11 100 6.3 x 11 125 8 x 11 130 5 x 11 110 5 x 11 115 6.3 x 11 145 6.3 x 11 150 6.3 x 11 135 8 x 11 190 100 5 x 11 100 150 5 x 11 120 6.3 x 11 130 8 x 11 180 8 x 11 200 10 x 12 240 220 6.3 x 11 165 6.3 x 11 180 6.3 x 11 180 8 x 11 200 10 x 12 315 8 x 11 235 10 x 12 250 8 x 11 315 10 x 12 355 10 x 12 380 10 x 12 285 10 x 15 440 8 x 11 315 10 x 15 440 10 x 12 395 10 x 19 460 13 x 20 580 330 470 6.3 x 11 161 8 x 11 200 6.3 x 11 225 8 x 11 280 8 x 11 8 x 11 255 305 10 x 15 470 680 10 x 12 320 10 x 12 420 10 x 15 530 10 x 19.5 650 13 x 20 730 1000 10 x 12 470 10 x 12 490 10 x 19.5 700 13 x 20 855 13 x 25 995 10 x 15 570 10 x 19.5 750 10 x 19.5 705 13 x 25 1020 16 x 25 1110 13 x 20 860 16 x 25 1230 16 x 25 1236 16 x 32 1450 16 x 36 1477 18 x 36 1660 1500 2200 3300 4700 10 x 15 13 x 20 13 x 20 16 x 25 600 930 1100 1320 10 x 19 800 13 x 20 991 13 x 20 1010 13 x 25 1150 13 x 25 1220 13 x 25 1150 16 x 25 1350 16 x 25 1330 16 x 32 1560 18 x 36 1790 16 x 25 1410 6800 16 x 25 1490 16 x 32 1610 10000 16 x 32 1830 18 x 36 1980 15000 18 x 36 2280 Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz 16 x 32 18 x 36 1450 1690 42 case size & permissible ripple current of standard products CAP. (μF) D x L: mm Rated Voltage W V (SURGE VOLTAGE W V) 50 (63) SIZE RIPPLE 63 (79) SIZE RIPPLE 100 (125) SIZE RIPPLE 160 (200) SIZE RIPPLE 200 (250) SIZE RIPPLE 0.47 5 x 11 7 5 x 11 8 5 x 11 10 5 x 11 12 5 x 11 12 1.0 5 x 11 12 5 x 11 12 5 x 11 15 5 x 11 17 6.3 x 11 17 2.2 5 x 11 18 5 x 11 20 5 x 11 22 6.3 x 11 25 6.3 x 11 25 3.3 5 x 11 25 5 x 11 27 5 x 11 29 8 x 11 36 8 x 11 36 4.7 5 x 11 30 5 x 11 34 5 x 11 37 6.3 x 11 34 10 x 12 50 8 x 11 43 6.8 5 x 11 30 5 x 11 37 5 x 11 46 10 x 12 54 10 x 12 60 10 5 x 11 50 5 x 11 55 6.3 x 11 65 10 x 12 70 10 x 12 69 10 x 15 80 15 5 x 11 50 5 x 11 65 8 x 11 82 10 x 15 90 10 x 19.5 110 22 5 x 11 75 6.3 x 11 90 8 x 11 115 10 x 19.5 130 10 x 15 140 10 x 19.5 150 13 x 20 220 13 x 25 190 13 x 20 220 13 x 25 260 16 x 20 242 16 x 25 280 33 47 68 100 6.3 x 11 105 6.3 x 11 101 8 x 11 125 8 x 11 159 8 x 11 169 8 x 11 8 x 11 10 x 12 110 155 198 10 x 12 260 10 x 12 10 x 15 10 x 19.5 160 210 241 10 x 19.5 305 13 x 20 13 x 25 13 x 25 180 250 270 16 x 25 390 16 x 32 400 10 x 12 210 13 x 20 385 150 10 x 12 289 10 x 15 330 13 x 25 414 16 x 32 435 16 x 36 450 220 10 x 12 346 10 x 19.5 465 13 x 25 495 16 x 36 700 18 x 40 850 10 x 15 400 16 x 25 590 18 x 40 750 10 x 19.5 535 16 x 25 720 18 x 40 780 13 x 20 600 22 x 40 920 10 x 19.5 560 13 x 20 650 18 x 45 800 13 x 20 730 13 x 25 800 22 x 40 920 680 13 x 25 860 16 x 25 1000 1000 16 x 25 1110 330 470 13 x 20 650 16 x 25 1023 16 x 32 1200 1500 16 x 32 1350 16 x 36 1450 2200 16 x 36 1360 18 x 45 1800 18 x 36 1530 Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz 16 x 32 16 x 36 875 1200 18 x 40 22 x 40 850 980 43 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm Rated Voltage W V (SURGE VOLTAGE W V) 250 (300) SIZE RIPPLE 350 (400) SIZE RIPPLE 400 (450) SIZE RIPPLE 450 (500) SIZE RIPPLE 0.47 5 x 11 12 6.3 x 11 14 6.3 x 11 14 6.3 x 11 16 1.0 6.3 x 11 17 6.3 x 11 15 6.3 x 11 15 8 x 11 22 8 x 11 20 8 x 11 20 10 x 12 35 8 x 11 28 10 x 12 37 10 x 12 35 10 x 12 42 10 x 12 42 10 x 15 49 10 x 15 51 10 x 15 59 2.2 3.3 4.7 6.3 x 11 23 8 x 11 29 8 x 11 34 10 x 12 42 8 x 11 41 10 x 12 43 10 x 12 66 10 x 12 52 10 x 15 55 10 x 15 57 10 x 15 47 6.8 10 x 12 62 10 x 19.5 65 10 x 15 67 13 x 20 69 10 10 x 15 75 10 x 15 65 10 x 19.5 75 10 x 19.5 72 10 x 19.5 88 13 x 20 95 13 x 20 97 13 x 25 99 15 13 x 20 120 13 x 20 140 13 x 25 145 16 x 25 150 22 13 x 20 130 13 x 20 125 13 x 20 120 16 x 25 145 13 x 25 155 16 x 25 165 13 x 25 140 16 x 32 175 16 x 20 147 16 x 25 170 33 47 68 100 13 x 25 200 16 x 20 150 16 x 20 164 16 x 32 211 16 x 32 195 16 x 25 190 18 x 36 250 18 x 40 350 22 x 40 380 18 x 16 148 16 x 32 230 13 x 25 228 16 x 36 210 16 x 25 200 16 x 25 270 18 x 36 240 16 x 32 250 18 x 25 243 18 x 36 300 18 x 25 310 18 x 36 325 16 x 32 300 18 x 36 320 16 x 36 300 18 x 40 300 18 x 32 260 18 x 36 440 22 x 40 360 18 x 36 290 22 x 40 365 18 x 32 289 18 x 36 320 18 x 40 350 22 x 40 465 120 150 18 x 40 600 220 22 x 40 800 Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz 22 x 40 480 Yageo corporation ELECTROLYTIC CAPACITORS Miniature Aluminum Electrolytic Capacitors SG [ Electronic Ballast ] 105°C Single-Ended Lead Aluminum Electrolytic Capacitors Electrical Characteristics Operating Temperature Range : -40 ~ +105°C / -25 ~ +105°C Rated Voltage Range : 160 ~ 400V / 450V Rated Capacitance Range : 4.7 ~ 330µF / 3.3~100µF Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C DC Leakage Current (μA): I = 0.06CV (μA) + 10μA Whichever is greater. (After Rated Voltage Applied for 2 Minutes) MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient FREQUENCY (Hz) 50 60 120 6.3~100V Below~68μF 0.50 0.625 0.75 FREQUENCY (Hz) 1K 10K~100K 6.3~100V Below~68μF 0.875 1.00 Dissipation Factor WV (V) : 160 D.F. (%) : 15 200 15 250 15 350 20 400 24 450 24 Endurance : After applying rated voltage with rated ripple current for 5000 hours at 105°C, the capacitors shall meet the following requirements. (a) Capacitance Change : Within 20% of Initial Value (b) Dissipation Factor : 200% or Less of Initial Specified Value (c) Leakage Current : Initial Specified Value or Less Shelf Life : After placed at 105°C without voltage applied for 1000 hours, the capacitors shall meet the same requirement as Endurance. diagram of dimensions Dimensions: mm Rubber Stand-off Vinyl Sleeve (P.V.C) Rubber End Seal Vinyl Sleeve (P.V.C) Rubber End Seal F±0.5 F±0.5 L 15Min. 5Min. D±0.5 L L ≤ 16 L + 1.5Max. L > 16 L + 2Max. Dø = 8 & 10 L + 2.5Max. 15Min. 5Min. Dø F dø 5.0 2.0 0.5 6.3 2.5 8.0 3.5 10.0 5.0 0.6 12.0 D±0.5 Dø < 20 : Dø+0.5 Dø ≥ 20 : Dø+1 13.0 16.0 7.5 0.8 10.0 0.8 (1.0) 18.0 22.0 45 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) 160 (200) SIZE RIPPLE 200 (250) IMPEDANCE SIZE 10 *10 x 15 15 22 33 47 68 100 150 220 330 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 10 x 19.5 10 x 19.5 13 x 20 256 336 416 1.52 1.30 0.95 RIPPLE 250 (300) IMPEDANCE SIZE RIPPLE IMPEDANCE 160 2.50 *10 x 15 136 4.10 *10 x 19.5 160 3.50 *10 x 25 232 2.75 13 x 20 256 2.50 13 x 20 336 1.90 13 x 25 432 1.70 16 x 20 440 1.50 *10 x 15 128 5.00 10 x 19.5 256 1.50 *10 x 19.5 256 1.20 13 x 20 336 0.95 13 x 20 416 0.91 13 x 25 576 0.60 13 x 25 576 0.60 16 x 25 608 0.80 16 x 20 688 0.55 16 x 20 688 0.55 18 x 20 600 0.90 16 x 25 760 0.30 16 x 25 760 0.30 16 x 32 832 0.65 18 x 20 744 0.31 18 x 20 744 0.31 18 x 25 800 0.65 16 x 32 1040 0.22 18 x 25 1040 0.27 18 x 32 1040 0.45 18 x 25 1000 0.24 16 x 32 1200 0.22 18 x 32 1248 0.22 18 x 40 1312 0.35 18 x 25 1160 0.24 18 x 32 1536 0.22 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. Impedance: 100KHz / 20°C (Ω Max.) 3. * Down size: 3000 Hours 46 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 350 (400) SIZE RIPPLE 400 (450) IMPEDANCE SIZE RIPPLE 450 (500) IMPEDANCE SIZE 3.3 RIPPLE IMPEDANCE 10 x 19.5 96 6.50 4.7 *10 x 15 96 3.50 13 x 20 128 3.60 6.8 *10 x 15 115 3.40 *10 x 19.5 144 3.40 10 x 19.5 160 2.90 13 x 20 176 3.00 13 x 25 176 3.00 10 22 33 47 68 100 10 x 19.5 13 x 20 160 256 3.00 2.10 13 x 25 272 1.35 16 x 25 304 1.80 16 x 20 320 1.00 18 x 20 320 2.20 13 x 25 368 1.00 16 x 25 368 0.95 16 x 32 440 1.30 16 x 20 400 0.91 18 x 20 400 0.91 18 x 25 448 1.20 16 x 25 480 0.75 16 x 32 480 0.75 18 x 32 544 1.00 18 x 20 504 0.80 18 x 25 520 0.80 16 x 32 640 0.50 18 x 36 672 0.49 18 x 32 632 0.92 18 x 25 608 0.55 18 x 40 736 0.80 18 x 32 848 0.40 22 x 40 928 0.60 150 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. Impedance: 100KHz / 20°C (Ω Max.) 3. * Down size: 3000 Hours 18 x 40 872 0.34 22 x 40 1040 0.30 Yageo corporation ELECTROLYTIC CAPACITORS SP [ Miniature and Long Life ] Miniature Aluminum Electrolytic Capacitors 105°C Single-Ended Lead Aluminum Electrolytic Capacitors For Electronic Ballast Electrical Characteristics Operating Temperature Range : -40 ~ +105°C / -25 ~ +105°C Rated Voltage Range : 160 ~ 400V / 450V Rated Capacitance Range : 3.3 ~ 330µF Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C DC Leakage Current (μA) : I = 0.04CV (μA) + 100μA Whichever is greater. (After Rated Voltage Applied for 2 Minutes) description Dissipation Factor W V (V): 160 D.F (%) : 20 Applicable for Electronic Ballast 200 20 400 24 High Temperature Load Life at 105°C for 8000~10000 Hours 450 24 Low Temperature Stability Impedance Ratio (Max.) W V (V) : 160 200 400 450 Z - 25°C / Z + 20°C 3 3 5 6 Z - 40°C / Z + 20°C 6 6 6 - MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient Endurance: The following specifications shall be satisfied when the capacitors are stored to 20°C after subjected to DC Voltage with the maximum ripple current which is applied for 10,000 hours (8000 hours for 10ø) at 105°C. (a) Capacitance Change : Within 20% of Initial Value (b) Dissipation Factor : Not Exceed 200% of Initial Requirement (c) Leakage Current : Not Exceed the Initial Requirement FREQUENCY (Hz) 120 1K 10K 100K COEFFICIENT 0.50 0.80 0.90 1.00 Temperature Coefficient TEMPERATURE (°C) 65 85 105 FACTOR 1.70 1.40 1.00 Shelf Life : After placed at 105°C without voltage applied for 1000 hours, the capacitors shall meet the same requirement as Endurance. diagram of dimensions Dø F dø 10.0 5.0 0.6 Dimensions: mm Rubber Stand-off F±0.5 7.5 0.8 L 18.0 22.0 Rubber End Seal F±0.5 13.0 16.0 Vinyl Sleeve (P.V.C) Rubber End Seal Vinyl Sleeve (P.V.C) 12.0 10.0 L ≤ 16 L + 1.5Max. l > 16 L + 2Max. Dø = 8 & 10 L + 2.5Max. 15Min. 5Min. D±0.5 Dø < 20 Dø + 0.5 Dø ≥ 20 Dø + 1 L 15Min. 5Min. D±0.5 48 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 160 (200) SIZE 450 (500) SIZE RIPPLE 3.3 10 x 15 100 4.7 10 x 19.5 140 10 x 19.5 150 12.5 x 20 180 RIPPLE 200 (250) SIZE RIPPLE 6.8 10 x 19.5 10 22 33 47 68 100 150 220 330 400 (450) SIZE 10 x 19.5 10 x 19.5 500 440 10 x 19.5 520 12.5 x 20 580 13 x 20 660 10 x 19.5 580 12.5 x 20 660 12 x 25 720 13 x 25 720 16 x 20 760 16 x 20 760 13 x 25 970 16 x 25 1120 16 x 20 1120 16 x 25 1120 18 x 20 1120 16 x 25 1200 16 x 32 1280 16 x 32 1300 18 x 25 1300 16 x 32 1300 18 x 25 1300 18 x 36 1380 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz RIPPLE 150 10 x 19.5 180 12.5 x 20 310 16 x 20 300 16 x 25 560 18 x 20 550 16 x 32 620 18 x 25 590 16 x 36 880 18 x 32 880 16 x 25 16 x 32 18 x 32 520 700 870 Yageo corporation ELECTROLYTIC CAPACITORS SB [ For Low Leakage Current ] Miniature Aluminum Electrolytic Capacitors 105°C Single-Ended Lead Aluminum Electrolytic Capacitors electrical characteristics Operating Temperature Range : -40 ~ +105°C Rated Voltage Range : 6.3 ~ 100V Rated Capacitance Range : 0.1 ~ 4700µF Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C DC Leakage Current (µA) : I = 0.002CV (µA) or 0.4µA Whichever is greater. (After Rated Voltage Applied for 2 Minutes) description Dissipation Factor W V (V): 6.3 10 16 25 35 ~ 100 D.F. (%) : 20 16 13 12 10 When nominal capacitance is over 1000μF, tan δ shall be added 0.02 to the listed value with increase of every 1000μF Used in where low leakage current is essential as in coupling of pre-amplifies. Low Temperature Stability Impedance Ratio (Max.) W V (V) : 6.3 10 Impedance: Z - 40°C / Z + 20°C 4 4 16 ~ 100 3 Very low leakage current remains even after prolonged storage. MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient FREQUENCY (Hz) 50 120 300 1K 10K 6.3~25V 0.85 1.00 1.04 1.08 1.19 Endurance: After applying rated voltage for 1000 hours at 105° C, the capacitors shall meet the following requirements. (a) Capacitance Change : Within 25% of Initial Value (b) Dissipation Factor : Not more than 200% of Specified Value (c) Leakage Current : Not more than the Specified Value 26~50V 0.80 1.00 1.30 1.40 1.43 50~100V 0.77 1.00 1.34 1.43 1.48 TEMPERATURE (°C) 60 70 85 105 Shelf Life : After 500 Hours at 105° C without Applying Rated Voltage (a) Capacitance Change : Within 25% of Initial Value (b) Dissipation Factor : Not more than 200% of Specified Value (c) Leakage Current : Not more than 200% of Specified Value FACTOR 1.95 1.75 1.20 1.00 Temperature Coefficient diagram of dimensions Dø 4.0 F 1.5 dø 0.45 5.0 2.0 0.5 6.3 2.5 8.0 3.5 10.0 5.0 Rubber End Seal Vinyl Sleeve dø Dø±0.5 13.0 F±0.5 L 7.5 18.0 22.0 Rubber Stand-off 0.6 12.0 16.0 Dimensions: mm 10.0 15Min. 5Min. 0.8 L ≤ 16 L + 1.5Max. L > 16 L + 2Max. Dø = 8 & 10 L + 2.5Max. Dø < 20 Dø + 0.5 Dø ≥ 20 Dø + 1 F±0.5 50 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 6.3 (8) SIZE 16 (20) SIZE RIPPLE 10 5 x 11 40 15 5 x 11 56 RIPPLE 10 (13) SIZE RIPPLE 22 5 x 11 68 6.3 x 11 70 33 6.3 x 11 78 6.3 x 11 95 47 6.3 x 11 106 6.3 x 11 100 8 x 11 122 68 6.3 x 11 80 6.3 x 11 142 8 x 11 168 100 6.3 x 11 126 8 x 11 179 8 x 11 210 10 x 12 264 10 x 15 416 150 8 x 11 196 8 x 11 220 10 x 12 280 220 10 x 12 272 10 x 15 355 10 x 19.5 553 330 10 x 15 388 10 x 19.5 480 13 x 20 732 470 10 x 19.5 507 13 x 20 640 13 x 20 1040 680 13 x 20 700 13 x 20 848 13 x 25 1280 820 13 x 25 850 13 x 25 980 16 x 25 1450 1000 13 x 25 896 13 x 25 1081 16 x 25 1700 1500 13 x 25 1204 16 x 25 1376 16 x 32 1750 2200 16 x 25 1513 16 x 32 1680 18 x 36 1900 3300 16 x 36 1902 16 x 36 2155 18 x 40 2250 4700 18 x 36 2272 18 x 40 2560 Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz 51 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 25 (32) SIZE 50 (63) SIZE RIPPLE 0.1 5 x 11 1 0.15 5 x 11 4 0.22 5 x 11 4 0.33 5 x 11 6 0.47 5 x 11 7 0.56 5 x 11 7 0.68 5 x 11 9 1.0 5 x 11 18 1.5 5 x 11 24 2.2 5 x 11 30 3.3 5 x 11 36 RIPPLE 35 (44) SIZE RIPPLE 4.7 5 x 11 27 5 x 11 40 6.3 x 11 45 6.8 5 x 11 42 5 x 11 45 6.3 x 11 55 10 6.3 x 11 63 5 x 11 55 8 x 11 82 6.3 x 11 67 15 6.3 x 11 67 8 x 11 75 8 x 11 97 22 6.3 x 11 61 8 x 11 97 10 x 12 127 8 x 11 84 33 8 x 11 102 10 x 12 139 10 x 15 156 47 10 x 12 141 10 x 12 166 10 x 15 217 68 10 x 12 190 10 x 15 238 10 x 19.5 300 100 10 x 15 277 8 x 11 200 13 x 20 390 10 x 19.5 310 150 10 x 19.5 455 13 x 20 491 13 x 25 569 220 13 x 20 590 13 x 25 630 16 x 25 910 330 13 x 25 754 10 x 15 450 16 x 32 986 16 x 25 771 470 16 x 25 1110 16 x 25 1150 16 x 36 1249 680 16 x 32 1385 16 x 32 1462 16 x 36 1870 820 16 x 32 1540 16 x 36 1630 16 x 36 1950 1000 16 x 36 1710 18 x 36 1723 18 x 40 2070 1500 16 x 36 1779 18 x 40 2006 2200 18 x 40 2174 Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz 52 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) D x L: mm Rated Voltage w v (SURGE VOLTAGE W V) 63 (79) SIZE RIPPLE 80 (100) SIZE RIPPLE 100 (125) SIZE RIPPLE 0.1 5 x 11 1 5 x 11 1 5 x 11 1 0.15 5 x 11 4 5 x 11 4 5 x 11 4 0.22 5 x 11 4 5 x 11 4 5 x 11 4 0.33 5 x 11 6 5 x 11 6 5 x 11 6 0.47 5 x 11 7 5 x 11 7 5 x 11 7 0.56 5 x 11 7 5 x 11 7 5 x 11 7 0.68 5 x 11 9 5 x 11 9 5 x 11 9 1.0 4x7 12 5 x 11 18 5 x 11 18 5 x 11 18 1.5 5 x 11 24 5 x 11 24 5 x 11 24 2.2 5 x 11 30 5 x 11 30 6.3 x 11 30 3.3 5 x 11 36 6.3 x 11 36 8 x 11 36 4.7 6.3 x 11 45 6.3 x 11 45 8 x 11 60 6.8 6.3 x 11 55 8 x 11 60 10 x 12 67 10 8 x 11 82 10 x 12 90 10 x 15 94 15 10 x 12 103 10 x 15 112 10 x 19.5 117 22 10 x 15 148 10 x 15 165 10 x 19.5 187 33 10 x 15 210 10 x 19.5 217 13 x 20 225 47 10 x 19.5 240 10 x 19.5 276 13 x 25 285 68 10 x 19.5 328 13 x 20 361 13 x 25 375 100 13 x 25 420 13 x 25 447 16 x 25 456 150 13 x 25 648 16 x 25 663 16 x 32 707 220 16 x 32 930 16 x 32 970 16 x 36 1010 330 16 x 36 1088 16 x 36 1198 18 x 36 1377 470 18 x 36 1385 18 x 36 1509 680 18 x 36 1870 820 18 x 40 1950 Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz Yageo corporation ELECTROLYTIC CAPACITORS SN [ For Non Polar ] Miniature Aluminum Electrolytic Capacitors 105°C Single-Ended Lead Aluminum Electrolytic Capacitors For Non-Polar General Purpose Electrical Characteristics Operating Temperature Range : -40 ~ +105°C Rated Voltage Range : 6.3 ~ 100V Rated Capacitance Range : 0.22 ~ 2200µF Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C DC Leakage Current (µA) : I = 0.03 CV + 3µA (After Rated Voltage Applied for 2 Minutes) description Dissipation Factor W V (V): 6.3 10 16 25 35 50 100 D.F. (%) : 24 20 17 15 14 12 10 For capacitor whose capacitance exceeds 1000µF. The value of D.F is increased by 2% for every addition of 1000µF. Non-polar for used in reversing polarity DC voltage circuits. Endurance : 1000 Hours at 105°C with the Polarity Inverted Every 250 Hours (a) Capacitance Change : Within 25% of Initial Value (b) Dissipation Factor : Not more than 150% of Specified Value (c) Leakage Current : Not more than the Specified Value MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient FREQUENCY (Hz) 60 FACTOR 0.75 1.00 1.20 1.32 1.65 120 300 1K Temperature Coefficient Shelf Life : After placed at 105° C without voltage applied for 500 hours, the capacitors shall meet the same requirement as Endurance. TEMPERATURE (°C) 65 85 105 FACTOR 1.30 1.20 1.00 diagram of dimensions Dø F dø 4.0 1.5 0.45 5.0 2.0 0.5 6.3 2.5 5.0 0.6 Rubber Stand-off Rubber End Seal Vinyl Sleeve (P.V.C) Rubber End Seal Vinyl Sleeve (P.V.C) F±0.5 3.5 10.0 Dimensions: mm F±0.5 8.0 10K 12.0 13.0 L 16.0 7.5 18.0 22.0 10.0 0.8 L ≤ 16 L + 1.5Max. L > 16 L + 2Max. Dø = 8 & 10 L + 2.5Max. 15Min. 5Min. D±0.5 Dø < 20 Dø + 0.5 Dø ≥ 20 Dø + 1 L 15Min. 5Min. D±0.5 54 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 6.3 (8) SIZE RIPPLE 10 (13) SIZE RIPPLE 16 (20) SIZE RIPPLE 25 (32) SIZE RIPPLE 4.7 10 6.3 x 11 22 5 x 11 57 45 5 x 11 42 6.3 x 11 50 5 x 11 59 6.3 x 11 69 6.3 x 11 69 8 x 11 86 35 (44) SIZE RIPPLE 5 x 11 34 6.3 x 11 54 8 x 11 94 33 5 x 11 63 6.3 x 11 77 8 x 11 98 8 x 11 105 10 x 12 125 47 6.3 x 11 84 6.3 x 11 93 8 x 11 115 10 x 12 140 10 x 15 165 100 8 x 11 140 8 x 11 193 8 x 11 140 10 x 19.5 240 13 x 20 285 10 x 12 175 10 x 15 205 220 10 x 12 235 10 x 15 255 10 x 19.5 330 13 x 20 390 16 x 25 520 330 10 x 15 310 10 x 19.5 380 13 x 20 445 16 x 25 580 16 x 25 630 470 10 x 19.5 400 13 x 20 470 13 x 25 570 16 x 25 690 16 x 32 820 1000 13 x 25 690 16 x 25 885 16 x 32 1020 2200 16 x 32 1250 16 x 36 1450 Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz 55 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 50 (63) SIZE RIPPLE 63 (79) SIZE RIPPLE 80 (100) SIZE RIPPLE 100 (125) SIZE RIPPLE 0.22 5 x 11 5 0.47 5 x 11 11 5 x 11 11 5 x 11 11 5 x 11 14 1.0 5 x 11 17 5 x 11 17 5 x 11 17 5 x 11 21 2.2 5 x 11 25 5 x 11 25 5 x 11 29 6.3 x 11 34 3.3 6.3 x 11 31 6.3 x 11 37 6.3 x 11 39 8 x 11 49 4.7 5 x 11 34 5 x 11 37 8 x 11 47 8 x 11 58 6.3 x 11 41 6.3 x 11 44 6.3 x 11 56 8 x 11 74 10 x 12 88 8 x 11 80 8 x 11 70 10 x 12 100 6.3 x 11 75 8 x 11 95 8 x 11 97 10 x 15 130 10 x 12 115 8 x 11 110 8 x 11 115 10 x 15 150 10 x 19.5 175 8 x 11 130 13 x 20 10 x 19.5 190 100 13 x 20 310 220 16 x 25 570 330 16 x 36 790 10 22 33 47 Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz 10 x 19.5 150 13 x 20 180 13 x 20 205 13 x 20 220 230 13 x 20 245 13 x 25 285 16 x 25 410 16 x 25 435 16 x 32 510 16 x 32 660 Yageo corporation ELECTROLYTIC CAPACITORS Miniature Aluminum Electrolytic Capacitors SR [ For Horizontal Deflection ] Bi-Polarized Capacitors for Horizontal Deflection Circuits of TV Sets Electrical Characteristics Operating Temperature Range : -40 ~ +85°C Rated Voltage Range : 25, 35, 50V Rated Capacitance Range : 2.2 ~ 47μF Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C description DC Leakage Current : 100μA Max. ( After 2 Minutes Both Direction ) Bi-Palarized Type for Used in Horizontal Deflection Current Dissipation Factor : W V (V): 25 35 D.F. (%) : 5 5 Correction at High Frequency and High Ripple Currents Lower Cost to be Compared with other Film Capacitors MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient FREQUENCY (Hz) 60 FACTOR 120 0.4 0.4 400~1K 15.75K 0.8 1.0 50 5 Endurance: After Applying Rated Voltage for 1000 Hours at 85°C (Polarity Inverted Every 250 Hours) The Capacitors Shall Meet the Following Requirements. (a) Capacitance Change : Within 20% of Initial Value (b) Dissipation Factor : Not more than 150% of Specified Value (c) Leakage Current : Not more than the Specified Value Shelf Life : After placed at 85°C without voltage applied for 500 hours, the capacitors shall meet the same requirement as Endurance. Temperature Coefficient TEMPERATURE (°C) 65 70 85 FACTOR 1.15 1.00 0.80 diagram of dimensions Dimensions: mm Rubber Stand-off Rubber End Seal Vinyl Sleeve (P.V.C) Rubber End Seal Vinyl Sleeve (P.V.C) F±0.5 F±0.5 L 15Min. 5Min. D±0.5 L L ≤ 16 L + 1.5Max. L > 16 L + 2Max. Dø = 8 & 10 L + 2.5Max. 15Min. 5Min. Dø F dø 12.0 5.0 0.6 7.5 0.8 10.0 0.8 (1.0) 13.0 D±0.5 Dø < 20 Dø + 0.5 Dø ≥ 20 Dø + 1 16.0 18.0 22.0 57 case size & permissible ripple current of standard products CAP. (µF) D x L: mm Rated Voltage W V (SURGE VOLTAGE W V) 25 (32) SIZE RIPPLE 35 (44) SIZE RIPPLE 50 (63) SIZE RIPPLE 2.2 16 x 25 6 16 x 25 6 16 x 25 6 3.3 16 x 25 7 16 x 25 7 16 x 25 7 4.7 16 x 25 7 16 x 25 7 16 x 25 7 5.6 16 x 32 7 16 x 32 7 16 x 32 7 6.8 16 x 36 8 16 x 36 8 16 x 36 8 8.2 16 x 36 8 16 x 36 8 16 x 36 8 10 18 x 40 12 18 x 40 12 18 x 40 12 13 18 x 40 12 18 x 40 12 18 x 40 12 15 18 x 40 12 18 x 40 12 18 x 40 12 18 22 x 40 13 22 x 40 13 22 x 40 13 20 22 x 40 13 22 x 40 13 22 x 40 13 22 22 x 40 13 22 x 40 13 22 x 40 13 25 22 x 40 13 22 x 40 13 22 x 40 13 47 22 x 40 13 22 x 40 13 22 x 40 13 Note: 1. Ripple Current: (Ap-p) / Sawtooth Waveform 85°C, 15.75KHz Yageo corporation ELECTROLYTIC CAPACITORS Miniature Aluminum Electrolytic Capacitors SC [ For Low Impedance and Low ESR Suitable for Output of Motherboard ] 105°C Single-Ended Lead Aluminum Electrolytic Capacitors For High Frequency Applications Electrical Characteristics Operating Temperature Range : -40 ~ +105°C Rated Voltage Range : 6.3 ~ 100V Rated Capacitance Range : 4.7 ~ 15000µF Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C description DC Leakage Current (μA) : I = 0.01CV or 3μA Whichever is greater. (After Rated Voltage Applied for 2 Minutes) Applicable for switching regulator of compurter, especially for high frequency MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient FREQUENCY (Hz) 50 ~4.7µF 0.30 0.40 0.50 0.70 0.80 120 300 1K 10K 5.6~33µF 0.40 0.50 0.60 0.80 0.90 34~330µF 0.60 0.70 0.80 0.90 0.95 331~1000µF 0.65 0.90 0.90 0.98 1.00 1200µF Higher 0.85 0.90 0.95 0.98 1.00 Dissipation Factor W V (V): 6.3 10 16 25 35 50 63 100 D.F. (%) : 15 14 12 10 10 8 8 7 When nominal capacitance is over 1000μF, tan δ shall be added 0.02 to listed value with increase of every 1000μF. W V (V) : Impedance: Z - 40°C / Z + 20°C 6.3 8 10 6 16 4 25 4 35 4 50 4 63 4 100 4 Endurance : After applying rated voltage with ripple current for 3000 hours at 105°C, the capacitors shall meet the following requirements. If Dimension is Down Size, Endurance will be Less 1000 hours than Standard (a) Capacitance Change : Within ±20% of Initial Value (b) Dissipation Factor: Not more than 200% of Specified Value (c) Leakage Current: Not more than the Specified Value CASE size 5 x 11 ~ 10 x 12 10 x 15 Higher LIFE 2000 3000 Shelf Life : After placed at 105°C without voltage applied for 1000 hours, the capacitors shall meet the same requirement as Endurance. diagram of dimensions Dimensions: mm Rubber Stand-off Vinyl Sleeve (P.V.C) Rubber End Seal Vinyl Sleeve (P.V.C) Rubber End Seal Dø F dø 4.0 1.5 0.45 5.0 2.0 0.5 6.3 2.5 F±0.5 F±0.5 8.0 3.5 10.0 5.0 0.6 12.0 L 15Min. 5Min. D±0.5 L L ≤ 16 L + 1.5Max. L > 16 L + 2Max. Dø = 8 & 10 L + 2.5Max. 15Min. 5Min. D±0.5 Dø < 20 Dø + 0.5 Dø ≥ 20 Dø + 1 13.0 16.0 7.5 0.8 10.0 0.8 (1.0) 18.0 22.0 59 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 6.3 (8) SIZE RIPPLE ESR 10 (13) SIZE RIPPLE ESR 16 (20) SIZE RIPPLE ESR 10 25 (32) SIZE RIPPLE ESR *4 x 7 40 2.000 5 x 11 50 0.550 56 5 x 11 100 0.630 5 x 11 150 0.420 68 5 x 11 150 0.420 6.3 x 11 200 0.370 100 5 x 11 150 0.420 5 x 11 200 0.370 6.3 x 11 250 0.220 120 5 x 11 200 0.370 6.3 x 11 250 0.320 8 x 11 300 0.200 150 5 x 11 200 0.420 6.3 x 11 250 0.320 6.3 x 11 300 0.220 8 x 11 550 0.140 220 6.3 x 11 250 0.320 6.3 x 11 300 0.220 8 x 11 550 0.140 *8 x 11 620 0.120 8 x 15 750 0.100 270 *6.3 x 11 300 0.220 330 *6.3 x 11 320 0.230 8 x 11 0.180 470 680 400 8 x 11 550 0.140 0.120 *8 x 15 660 0.100 8 x 15 750 0.100 8 x 20 800 0.069 10 x 12 688 0.080 10 x 15 900 0.086 0.180 *8 x 11 620 0.120 *8 x 15 730 0.093 *8 x 20 1000 0.067 8 x 11 0.140 8 x 15 750 0.100 10 x 12 800 0.085 *10 x 12 900 0.086 10 x 15 1050 0.064 550 580 0.120 *8 x 11 640 0.110 8 x 15 700 0.100 10 x 12 800 0.085 820 8 x 20 750 0.085 10 x 15 1050 1000 *8 x 11 580 0.150 8 x 20 *8 x 15 670 0.085 8 x 20 800 10 x 12 10 x 15 1500 620 *6.3 x 11 440 *8 x 11 1200 *8 x 11 10 x 15 1050 0.064 10 x 19.5 1100 0.039 0.064 10 x 19.5 1100 0.044 10 x 19.5 1250 0.039 1080 0.065 *10 x 15 1140 0.043 *10 x 19.5 1160 0.047 10 x 12 930 0.075 10 x 19.5 1250 0.039 *10 x 25 1310 0.042 0.069 10 x 15 990 0.085 13 x 20 1450 0.038 690 0.080 10 x 19.5 1100 0.050 1000 0.064 10 x 19.5 1250 0.044 13 x 25 1600 0.029 *8 x 15 980 0.085 *8 x 20 1070 0.051 *10 x 15 1070 0.055 10 x 19.5 1250 0.044 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. ESR: 100KHz / 20°C (Ω Max.) 3. * Down Size: 1000 Hours 10 x 19.5 1450 0.039 *10 x 25 1310 0.042 13 x 20 1450 0.038 *10 x 19.5 1200 0.045 *12 x 30 1750 0.032 13 x 20 0.034 16 x 25 2000 0.028 1600 60 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 6.3 (8) SIZE ESR 16 (20) SIZE RIPPLE ESR 25 (32) SIZE RIPPLE ESR *10 x 19.5 1330 0.047 *10 x 30 1780 0.032 *13 x 30 1810 0.029 0.048 *10 x 25 1450 0.025 *13 x 20 1720 0.033 *16 x 25 1660 0.032 1450 0.043 13 x 20 1600 0.038 13 x 25 2000 0.028 16 x 32 2200 0.024 *10 x 25 1400 0.043 *10 x 30 1740 0.032 *13 x 40 2200 0.026 16 x 36 2540 0.019 13 x 25 1700 0.035 13 x 25 2000 0.028 16 x 25 2200 0.024 18 x 36 2550 0.019 3900 13 x 25 1750 0.032 4700 *12 x 30 1570 0.033 *13 x 25 1860 0.028 16 x 36 2550 0.019 18 x 36 2800 0.019 *13 x 25 1520 0.032 16 x 25 2200 0.024 16 x 25 1800 0.028 6800 16 x 32 2000 0.024 16 x 36 2550 0.019 18 x 36 2800 0.019 18 x 36 2800 0.019 8200 16 x 32 2350 0.019 18 x 36 2800 0.019 10000 16 x 36 2550 0.019 15000 18 x 36 3000 0.019 2200 3300 ESR 10 (13) SIZE *10 x 19.5 1220 0.051 *10 x 25 1310 13 x 20 RIPPLE Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. ESR: 100KHz / 20°C (Ω Max.) 3. * Down Size: 1000 Hours RIPPLE 61 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 35 (44) SIZE RIPPLE ESR 50 (63) SIZE RIPPLE ESR 63 (79) SIZE RIPPLE ESR 100 (125) SIZE RIPPLE ESR 4.7 5 x 11 115 1.200 5 x 11 115 2.000 5 x 11 115 2.200 5 x 11 120 2.000 6.8 5 x 11 120 1.000 5 x 11 120 1.850 5 x 11 120 2.000 5 x 11 140 1.850 10 5 x 11 140 0.900 5 x 11 140 1.700 5 x 11 140 1.850 6.3 x 11 200 1.500 15 5 x 11 170 0.690 5 x 11 180 1.200 5 x 11 200 1.700 6.3 x 11 250 1.200 22 5 x 11 190 0.420 5 x 11 200 0.700 6.3 x 11 250 1.200 8 x 11 300 0.790 33 5 x 11 200 0.420 6.3 x 11 250 0.600 6.3 x 11 300 0.900 8 x 15 450 0.590 47 6.3 x 11 250 0.370 6.3 x 11 300 0.520 8 x 11 450 0.700 10 x 15 550 0.350 68 6.3 x 11 300 0.220 8 x 11 450 0.350 8 x 11 550 0.520 10 x 19.5 650 0.240 100 *6.3 x 11 360 0.180 *8 x 11 480 0.290 8 x 20 650 0.350 13 x 20 800 0.180 8 x 11 450 0.140 8 x 15 550 0.250 120 8 x 11 550 0.130 8 x 20 650 0.210 10 x 15 800 0.300 13 x 25 1050 0.150 150 8 x 15 650 0.100 10 x 12 800 0.160 10 x 15 1050 0.200 13 x 25 1300 0.110 220 *8 x 15 730 0.075 *10 x 15 1050 0.100 10 x 19.5 1300 0.150 16 x 25 1400 0.071 10 x 12 800 0.069 10 x 25 1050 0.068 *10 x 15 900 0.052 10 x 19.5 1300 0.072 13 x 20 1400 0.100 16 x 32 1550 0.049 *10 x 19.5 1390 0.075 13 x 25 1550 0.064 18 x 36 1770 0.038 13 x 20 1400 0.060 330 470 10 x 19.5 1050 0.044 10 x 19.5 1300 0.039 680 13 x 20 1400 0.038 13 x 25 1550 0.050 16 x 25 1700 0.052 820 13 x 20 1550 0.034 16 x 25 1700 0.040 16 x 32 1900 0.048 1000 13 x 25 1700 0.029 16 x 25 1900 0.039 16 x 32 2100 0.042 1200 16 x 25 1900 0.028 16 x 32 2100 0.025 16 x 36 2550 0.036 1500 16 x 25 2100 0.024 16 x 36 2550 0.025 18 x 36 2800 0.033 2200 *16 x 32 2300 0.021 18 x 40 2800 0.025 16 x 36 2550 0.019 18 x 36 2880 0.019 3300 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. ESR: 100KHz / 20°C (Ω Max.) 3. * Down Size: 1000 Hours Yageo corporation ELECTROLYTIC CAPACITORS Miniature Aluminum Electrolytic Capacitors S J [ Low Impedance and High Ripple Series ] 105°C 1000 ~ 5000 Hours, Low Impedance and High Ripple Electrical Characteristics Operating Temperature Range : -40 ~ +105°C Rated Voltage Range : 6.3 ~ 100V Rated Capacitance Range : 5.6 ~ 6800µF Capacitance Tolerance : -20 ~ +20% at 120KHz description DC Leakage Current (µA) : I = 0.01 CV (µA) or 3µA Whichever is greater. AV (TV,Video, Audio), Monitor / Computer, OA / HA / Communication, Converter / Inverter, Adapter, SMPS Dissipation Factor W V (V): 6.3 D.F. (%) : 22 MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient FREQUENCY (Hz) 50 5.6~390µF 0.60 0.70 0.85 0.95 1.00 120 1K 10K 100K 470~1000µF 0.65 0.75 0.90 0.98 1.00 1200~6800µF 0.75 0.80 0.95 1.00 1.00 ENDURANCE CASE LIFE TIME (HOURS) L=7 1000 L ≥ 11 Dø ≤ 6.3 2000 Dø = 8 3000 Dø = 10 4000 Dø ≥ 13 5000 10 19 16 16 W V (V) : Impedance: Z - 25°C / Z + 20°C Z - 40°C / Z + 20°C 25 14 35 12 6.3 2 3 10 2 3 50 10 16 2 3 63 9 25 2 3 100 8 35 2 3 50 2 3 Shelf Life: After placed at 105°C without voltage applied for 1000 hours. (500 hours for L=7) The capacitor shall meet the same requirement as Endurance. Dimensions: mm Rubber Stand-off Vinyl Sleeve (P.V.C) Rubber End Seal Rubber End Seal 15Min. 5Min. F±0.5 F±0.5 L D±0.5 100 2 3 Endurance: After applying rated voltage with maximum ripple current for 1000~5000 hours at 105°C, the capacitor shall meet the following requirement. (a) Capacitance Change: Within±25% of the Initial Value (b) Dissipation Factor: Not more than 200% of the Specified Value (c) Leakage Current: Not more than the Specified Value diagram of dimensions Vinyl Sleeve (P.V.C) 63 2 3 L L ≤ 16 L + 1.5Max. L > 16 L + 2Max. Dø = 8 & 10 L + 2.5Max. 15Min. 5Min. D±0.5 Dø < 20 Dø + 0.5 Dø ≥ 20 Dø + 1 Dø F dø 4.0 1.5 0.45 5.0 2.0 0.5 6.3 2.5 8.0 3.5 10.0 5.0 0.6 13.0 16.0 18.0 7.5 0.8 63 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 6.3 (8) SIZE RIPPLE ESR 10 (13) SIZE RIPPLE ESR 16 (20) SIZE RIPPLE ESR 25 (32) SIZE RIPPLE ESR 10 15 18 35 (44) SIZE RIPPLE ESR 4x7 130 0.96 4x7 130 0.94 5x7 190 0.57 4x7 130 0.92 5x7 170 0.69 5x7 210 0.47 27 4x7 130 0.89 5x7 190 0.61 5x7 210 0.46 5 x 11 230 0.37 33 5x7 160 0.75 5x7 210 0.45 5 x 11 220 0.42 5 x 11 250 0.3 39 4x7 130 0.85 5x7 175 0.64 5 x 11 220 0.43 5 x 11 230 0.36 6.3 x 7 300 0.25 47 5x7 175 0.7 5x7 190 0.53 5 x 11 230 0.36 5 x 11 250 0.30 6.3 x 11 380 0.15 8x7 350 0.19 6.3 x 11 410 0.13 8x7 380 0.16 8 x 11 510 0.12 8 x 11 620 0.105 56 68 100 120 150 180 5x7 5x7 190 210 0.56 0.43 5 x 11 200 0.43 6.3 x 7 240 0.35 5 x 11 220 0.38 6.3 x 7 270 0.29 5 x 11 250 0.3 6.3 x 7 300 0.23 8x7 340 0.18 5x7 5 x 11 5 x 11 6.3 x 7 210 210 250 300 0.44 0.44 0.3 0.23 5 x 11 6.3 x 7 250 300 0.3 0.24 6.3 x 7 300 0.24 6.3 x 11 340 0.19 8x7 310 0.22 6.3 x 11 370 0.16 6.3 x 11 410 0.13 8x7 350 0.18 8x7 380 0.15 6.3 x 11 410 0.13 8 x 11 560 0.12 8 x 11 680 0.088 8x7 380 0.15 8x7 350 0.18 8 x 11 510 0.12 8 x 11 630 0.105 8 x 11 760 0.072 8x7 380 0.15 8 x 11 560 0.11 8 x 11 690 0.088 8 x 15 910 0.068 10 x 12 930 0.065 220 8x7 380 0.15 6.3 x 11 410 0.13 8 x 11 620 0.1 8 x 11 760 0.072 10 x 12 1030 0.053 270 6.3 x 11 370 0.16 8 x 11 0.12 8 x 11 690 0.088 8 x 15 900 0.068 8 x 20 1250 0.041 10 x 12 930 0.065 580 330 6.3 x 11 410 0.13 8 x 11 640 0.1 8 x 11 760 0.072 10 x 12 1030 0.053 10 x 15 1430 0.038 470 8 x 11 0.086 8 x 11 760 0.072 8 x 15 1000 0.056 8 x 20 1250 0.041 10 x 19.5 1820 0.026 10 x 12 1030 0.053 10 x 15 1430 0.038 10 x 19.5 1650 0.032 10 x 25 2150 0.023 10 x 19.5 1820 0.026 13 x 20 2360 0.023 560 680 8 x 11 8 x 15 680 760 900 0.072 0.062 8 x 15 910 0.068 8 x 20 1140 0.049 10 x 12 940 0.064 10 x 15 1300 0.046 10 x 12 1030 0.053 8 x 20 1250 0.041 10 x 15 1430 0.038 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. ESR: 100KHz / 20°C (Ω Max.) 64 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) 820 1000 1200 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 6.3 (8) SIZE RIPPLE ESR 10 (13) SIZE RIPPLE ESR 16 (20) SIZE RIPPLE ESR 25 (32) SIZE RIPPLE ESR 35 (44) SIZE RIPPLE ESR 8 x 15 1000 8 x 20 10 x 19.5 1650 0.032 10 x 25 2150 0.023 13 x 25 2510 0.02 10 x 19.5 1820 0.026 13 x 20 2360 0.021 13 x 25 2770 0.018 10 x 25 2150 0.023 13 x 25 2510 0.02 13 x 30 3290 0.016 16 x 20 3140 0.018 10 x 12 1030 0.056 0.053 1130 0.05 10 x 15 1300 0.046 8 x 20 1250 0.041 10 x 15 1430 0.038 10 x 19.5 1820 0.026 8 x 20 1250 0.041 10 x 15 1430 0.038 1500 10 x 19.5 1820 0.026 10 x 25 2150 0.023 13 x 20 2360 0.021 13 x 25 2770 0.018 13 x 35 3400 0.015 1800 10 x 25 0.025 13 x 20 2230 0..022 13 x 25 2510 0.02 13 x 30 3290 0.016 16 x 25 3460 0.016 16 x 20 3140 0.018 1940 2200 10 x 25 2150 0.023 13 x 20 2360 0.021 13 x 25 2770 0.018 13 x 35 3400 0.015 2700 13 x 20 2230 0.022 13 x 25 2510 0.02 13 x 30 3290 0.016 16 x 25 3460 0.016 16 x 20 3140 0.018 3300 13 x 20 2360 0.021 13 x 25 2770 0.018 13 x 35 3400 0.015 3900 13 x 25 2770 0.018 13 x 30 3290 0.016 16 x 25 3460 0.016 16 x 20 3140 0.018 4700 13 x 30 3290 0.016 13 x 35 3400 0.015 5600 13 x 35 3400 0.015 16 x 25 3460 0.016 16 x 20 3140 0.018 16 x 25 3460 0.016 6800 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. ESR: 100KHz / 20°C (Ω Max.) 65 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) D x L: mm Rated Voltage W V (SURGE VOLTAGE W V) 50 (63) SIZE RIPPLE ESR 5.6 4x7 130 1 6.8 5x7 170 10 5x7 15 63 (79) SIZE 100 (125) SIZE RIPPLE ESR 0.74 5 x 11 125 1.40 210 0.50 6 x 11 170 0.95 6x7 220 0.38 5 x 11 215 0.48 6x7 300 0.26 5 x 11 240 0.34 27 8x7 340 33 8x7 39 RIPPLE ESR 5 x 11 170 0.88 6 x 11 210 0.57 6 x 11 220 0.65 8 x 11 330 0.44 0.21 6 x 11 240 0.43 8 x 11 360 0.36 380 0.17 6 x 11 270 0.35 8 x 15 375 0.30 6 x 11 330 0.16 8 x 11 385 0.31 8 x 15 450 0.25 47 6 x 11 360 0.15 8 x 11 420 0.26 10 x 12 450 0.24 56 6 x 11 390 0.14 8 x 11 500 0.26 8 x 20 570 0.19 68 8 x 11 600 0.11 8 x 15 610 0.19 10 x 15 580 0.18 10 x 12 625 0.18 8 x 15 670 0.16 10 x 19.5 750 0.13 10 x 12 625 0.15 13 x 16 740 0.13 22 82 8 x 11 660 0.09 100 8 x 11 730 0.07 10 x 15 800 0.12 10 x 25 880 0.12 120 8 x 15 950 0.07 8 x 20 820 0.12 13 x 20 1050 0.09 10 x 15 950 0.11 10 x 19.5 1010 0.096 13 x 25 1100 0.085 13 x 16 1040 0.098 10 x 19.5 1100 0.08 13 x 25 1200 0.071 13 x 16 1140 0.082 10 x 25 1300 0.073 13 x 30 1410 0.063 16 x 20 1300 0.071 13 x 35 1560 0.052 16 x 25 1600 0.053 18 x 20 1470 0.069 150 180 220 270 10 x 12 8 x 20 10 x 15 10 x 19.5 980 1190 1370 1580 0.06 0.05 0.04 0.03 13 x 20 1500 0.06 330 10 x 25 1870 0.028 13 x 25 1850 0.043 13 x 40 1700 0.046 390 13 x 20 1870 0.028 13 x 30 2050 0.047 16 x 32 1750 0.041 16 x 20 1810 0.054 13 x 40 1700 0.049 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. ESR: 100KHz / 20°C (Ω Max.) 66 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) 470 560 680 820 1000 D x L: mm Rated Voltage W V (SURGE VOLTAGE W V) 50 (63) SIZE RIPPLE ESR 63 (79) SIZE RIPPLE ESR 100 (125) SIZE RIPPLE ESR 13 x 20 2050 0.027 13 x 30 2250 0.045 16 x 36 1890 0.033 16 x 20 1990 0.045 18 x 32 1780 0.039 13 x 25 2450 0.035 16 x 40 2080 0.03 16 x 25 2550 0.032 18 x 36 2060 0.031 13 x 40 2780 0.029 18 x 40 2570 0.028 18 x 20 2450 0.038 13 x 25 13 x 30 2410 2860 0.023 0.021 13 x 35 2960 0.019 16 x 32 2810 0.026 16 x 20 2730 0.023 18 x 25 2780 0.031 16 x 32 3350 0.021 16 x 36 2840 0.021 18 x 32 3270 0.025 16 x 40 3340 0.019 18 x 36 3310 0.02 18 x 40 3420 0.018 1200 1500 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. ESR: 100KHz / 20°C (Ω Max.) Yageo corporation ELECTROLYTIC CAPACITORS SQ [ For Adapter and Power Supply Applications Series ] Miniature Aluminum Electrolytic Capacitors 105°C 2000 Hours, Wide Temperature Range and Low Impedance Electrical Characteristics Operating Temperature Range : -40 ~ +105°C Rated Voltage Range : 160V ~ 450DC Rated Capacitance Range : 2.2 ~ 220μF Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C DC Leakage Current (μA) : I ≤ 0.03CV + 10μA (After Rated Voltage Applied for 3 Minutes) I = Leakage Current (μA), C = Nominal Capacitance (μF), V = Rated Voltage (V) description Dissipation Factor W V (V): 160 D.F. (%) : 15 Recommended Applications: AV (TV, Video, Audio), Monitor / Computer, OA / HA / Communication, Converter / Inverter, Energy Saving Lamp, PFC Circuit, SMPS, Ballast, Adapter 200 15 250 15 W V (V) : Impedance: Z - 25°C / Z + 20°C Z - 40°C / Z + 20°C 350 24 400 24 160 3 6 450 24 200 3 6 250 3 6 350 3 6 400 3 6 450 3 6 Endurance : After apply rated voltage with rated ripple current for 2000hours at 105°C. The capacitors shall meet the following reuirements. (a) Capacitance Change : Within 20% of Initial Value (b) Dissipation Factor : Not more than 200% of the Specified Value (c) Leakage Current : Not more than the Specified Value MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient FREQUENCY (Hz) 50 1K 10K 100K < 33μF 0.45 0.75 0.85 1.00 ≥ 33μF 0.6 0.9 0.95 1.00 Shelf Life: After leaving capacitors under no load at 105°C for 1000 hours, the capacitors shall meet the same requirement as Endurance. diagram of dimensions Dimensions: mm Rubber Stand-off dø 10.0 5.0 0.6 7.5 0.8 Vinyl Sleeve (P.V.C) Rubber End Seal Vinyl Sleeve (P.V.C) Rubber End Seal F±0.5 F F±0.5 Dø 13.0 L 16.0 18.0 L ≤ 16 L + 1.5Max. L > 16 L + 2Max. Dø = 8 & 10 L + 2.5Max. 15Min. 5Min. D±0.5 Dø < 20 Dø + 0.5 Dø ≥ 20 Dø + 1 L 15Min. 5Min. D±0.5 68 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 160 (200) SIZE RIPPLE 120Hz ESR 100KHz 200 (250) SIZE RRIPPLE 120Hz 100KHz ESR 10 250 (300) SIZE RIPPLE 120Hz 100KHz 10 x 19.5 120 220 2.80 ESR 22 10 x 19.5 195 350 1.00 10 x 19.5 195 350 1.00 13 x 25 165 300 1.40 33 13 x 20 315 450 0.71 13 x 20 365 520 0.71 13 x 25 280 400 1.20 47 13 x 25 420 600 0.46 13 x 25 420 600 0.46 16 x 25 505 720 0.50 68 13 x 25 420 600 0.45 16 x 25 665 950 0.25 16 x 32 570 810 0.22 100 16 x 25 665 950 0.24 16 x 32 840 1200 0.17 18 x 36 735 1050 0.20 220 18 x 36 980 1400 0.14 Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz & 100KHz 2. ESR: 100KHz / 20°C (Ω Max.) 69 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 350 (400) SIZE RIPPLE 120Hz 400 (450) SIZE RIPPLE 120Hz 450 (500) SIZE RIPPLE 120Hz 100KHz 100KHz 100KHz 2.2 10 x 15 30 50 3.50 10 x 15 80 140 4.20 10 x 15 60 110 7.90 3.3 10 x 15 35 60 3.50 10 x 19.5 110 195 2.90 10 x 19.5 75 135 6.20 4.7 10 x 19.5 45 78 2.50 10 x 25 120 220 2.30 13 x 20 105 190 3.70 10 13 x 20 75 130 1.40 13 x 25 200 360 1.30 13 x 25 140 250 2.60 22 16 x 25 115 205 0.73 16 x 25 315 570 0.65 16 x 32 265 480 1.00 33 16 x 32 180 255 0.65 16 x 32 490 700 0.46 18 x 36 455 650 0.65 47 18 x 32 225 320 0.50 18 x 32 600 860 0.33 100 18 x 45 370 530 0.45 ESR Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz & 100KHz 2. ESR: 100KHz / 20°C (Ω Max.) ESR ESR Yageo corporation ELECTROLYTIC CAPACITORS Miniature Aluminum Electrolytic Capacitors SY [ For Low Impedance and Low ESR Suitable for Output of Motherboard ] 105°C Single-Ended Lead Aluminum Electrolytic Capacitors for High Frequency Applications Electrical Characteristics Operating Temperature Range : -40 ~ +105°C Rated Voltage Range : 6.3 ~ 100V Rated Capacitance Range : 6.8 ~15,000μF Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C description Features: Low ESR, high permissible ripple current at high frequency and long life than SC Recommended Applications: Used switching regulator applications in computers. Especially for high frequency. MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient FREQUENCY (Hz) 120 1K 10K 100K 22~180µF 0.40 0.75 0.90 1.00 220~560µF 0.50 0.85 0.94 1.00 680~1800µF 0.60 0.87 0.95 1.00 2200~3900µF 0.75 0.90 0.95 1.00 4700µF Higher 0.85 0.95 0.98 1.00 Leakage Current (Max.) (20°C): I = 0.01CV or 3μA Whichever is greater. (After Rated Voltage Applied for 2 Minutes) I = Leakage Current (μA), C = Nominal Capacitance (μF), V = Rated Voltage (V) Dissipation Factor W V (V): 6.3 D.F. (%) : 22 10 19 16 16 25 14 35 12 50 10 63 9 100 8 When nominal capacitance is over 1,000uF, tan δ shall be added 0.02 to the listed value with increase of every 1000μF. W V (V) : Rated Voltage (V) 6.3 10 16 25 35 50 63 100 Impedance : Z - 25°C / Z + 20°C 4 3 2 2 2 2 2 2 Z - 40°C / Z + 20°C 8 6 4 3 3 3 3 3 Endurance Dø : 5ø~6.3ø 8ø~10øx12.5 10øx15~12ø 13ø~18ø Life : 3000hrs 4000hrs 5000hrs 6000hrs After applying rated voltage with rated ripple current for 6000 hours at 105°C. The capacitors shall meet the following requirements. (a) Capacitance Change : Within 25% of Initial Value (b) Dissipation Factor : Not more than 200% of Specified Value (c) Leakage Current : Not more than the Specified Value Shelf Life : After placed at 105°C without voltage applied for 1000 hours, the capacitors shall meet the same requirement as Endurance. diagram of dimensions Dimensions: mm Rubber Stand-off Rubber End Seal Vinyl Sleeve F±0.5 F±0.5 Dø±0.5 dø L Dø < 20 Dø + 0.5 Dø ≥ 20 Dø + 1 L ≤ 16 L + 1.5Max. L > 16 L + 2Max. Dø = 8 & 10 L + 2.5Max. 15Min. 5Min. Dø F dø 5.0 2.0 0.5 6.3 2.5 8.0 3.5 10.0 5.0 0.6 12.0 13.0 16.0 18.0 7.5 0.8 71 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) 6.3 (8) SIZE RIPPLE ESR 10 (13) SIZE RIPPLE ESR 56 100 5 x 11 210 0.58 120 150 5 x 11 210 6.3 x 11 330 6.3 x 11 340 0.22 470 6.3 x 11 510 0.16 8 x 11 640 16 (20) SIZE RIPPLE ESR 5 x 11 210 0.580 6.3 x 11 250 0.230 6.3 x 11 340 0.220 6.3 x 11 469 0.185 8 x 11 582 0.150 8 x 11 640 0.130 8 x 15 840 0.087 8 x 20 950 0.078 10 x 12 865 0.080 10 x 15 1210 0.060 8 x 20 1050 0.069 10 x 15 1210 0.060 0.58 220 680 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 0.13 8 x 11 8 x 15 340 640 840 0.22 0.13 0.087 820 10 x 12 865 0.08 10 x 12 865 0.08 1000 8 x 15 840 0.087 8 x 20 1050 0.069 8 x 20 1050 0.069 10 x 15 1210 0.06 10 x 15 1210 0.060 10 x 19.5 1400 0.046 13 x 15 1450 0.049 1200 10 x 19.5 1400 0.046 10 x 25 1650 0.042 0.069 10 x 25 1650 0.042 10 x 30 1910 0.031 1210 0.06 13 x 15 1450 0.049 13 x 20 1900 0.035 10 x 19.5 1400 0.046 16 x 15 1940 0.042 1800 13 x 15 1450 0.049 2200 10 x 19.5 1400 0.046 10 x 30 1910 0.031 13 x 25 2230 0.027 10 x 25 1650 0.042 13 x 20 1900 0.042 18 x 15 2210 0.043 16 x 15 1940 0.042 18 x 15 2210 0.043 13 x 30 2650 0.024 16 x 20 2530 0.027 13 x 35 2880 0.020 1500 2700 3300 8 x 20 1050 0.069 10 x 15 1210 0.06 8 x 20 1050 10 x 15 10 x 30 1910 0.031 16 x 15 1940 0.042 10 x 25 1650 0.042 10 x 30 1910 0.031 13 x 20 1900 0.035 13 x 25 2230 0.027 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. ESR: 100KHz / 20°C (Ω Max.) 72 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) 3900 4700 5600 6800 8200 10000 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 6.3 (8) SIZE RIPPLE ESR 10 (13) SIZE RIPPLE ESR 16 (20) SIZE RIPPLE ESR 13 x 25 2230 0.027 13 x 30 2650 0.024 13 x 40 3350 0.017 18 x 15 2210 0.043 16 x 20 2530 0.027 16 x 25 2930 0.021 18 x 20 2860 0.026 16 x 32 3450 0.017 18 x 25 3140 0.019 13 x 30 2650 0.024 13 x 35 2880 0.02 13 x 35 2880 0.02 13 x 40 3350 0.017 16 x 36 3610 0.015 16 x 20 2530 0.027 16 x 25 2930 0.021 18 x 32 4170 0.015 18 x 20 2860 0.026 16 x 40 4080 0.013 18 x 36 4220 0.014 18 x 40 4280 0.012 13 x 40 3350 0.017 16 x 32 3450 0.017 16 x 25 2930 0.021 18 x 25 3140 0.019 18 x 20 2860 0.026 16 x 32 3450 0.017 16 x 36 3610 0.015 18 x 32 4170 0.015 16 x 36 3610 0.015 16 x 40 4080 0.013 18 x 25 3410 0.017 18 x 36 4220 0.014 12000 18 x 32 4170 0.015 18 x 40 4280 0.012 15000 18 x 36 4220 0.014 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. ESR: 100KHz / 20°C (Ω Max.) 73 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 25 (32) SIZE RIPPLE ESR 35 (44) SIZE RIPPLE ESR 2.2 50 (63) SIZE RIPPLE ESR 5 x 11 85 2.280 4.7 5 x 11 130 2.400 5 x 11 135 2.000 10 5 x 11 275 0.390 5 x 11 100 1.200 5 x 11 180 0.700 22 33 5 x 11 210 0.580 6.3 x 11 245 0.490 6.3 x 11 275 0.390 6.3 x 11 300 0.520 56 6.3 x 11 340 0.220 6.3 x 11 295 0.300 68 6.3 x 11 500 0.170 82 6.3 x 11 540 0.160 6.3 x 11 580 0.150 8 x 11 555 0.170 8 x 15 730 0.120 10 x 12 760 0.120 8 x 20 910 0.091 10 x 15 1050 0.084 10 x 19.5 1220 0.060 13 x 15 1260 0.061 47 100 5 x 11 6.3 x 11 210 340 0.580 0.220 120 150 8 x 11 640 0.160 8 x 11 640 0.130 180 220 8 x 11 640 0.130 270 330 470 820 840 0.087 10 x 12 865 0.080 8 x 20 1050 0.069 8 x 15 840 0.087 10 x 19.5 1400 0.046 10 x 19.5 1400 0.058 10 x 12 865 0.080 10 x 15 1210 0.060 10 x 25 1440 0.055 8 x 20 1050 0.069 13 x 15 1450 0.049 13 x 20 1660 0.045 10 x 12 1050 0.070 16 x 15 1690 0.055 10 x 15 1210 0.060 13 x 25 1950 0.034 18 x 15 1930 0.054 13 x 30 2310 0.030 13 x 35 2510 0.025 16 x 20 2210 0.034 560 680 8 x 15 10 x 25 1650 0.042 10 x 19.5 1400 0.046 10 x 30 1910 0.031 13 x 15 1450 0.049 13 x 20 1900 0.035 16 x 15 1940 0.042 13 x 20 1900 0.035 10 x 25 1650 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. ESR: 100KHz / 20°C (Ω Max.) 0.042 74 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) 1000 1200 1500 1800 2200 25 (32) SIZE RIPPLE ESR 35 (44) SIZE RIPPLE ESR 50 (63) SIZE RIPPLE ESR 10 x 19.5 1400 0.046 13 x 25 2230 0.027 13 x 40 2920 0.021 10 x 30 1910 0.031 18 x 15 2210 0.043 16 x 25 2555 0.025 13 x 20 1900 0.035 18 x 20 2490 0.036 16 x 15 1940 0.042 18 x 15 2210 0.043 13 x 30 2650 0.024 16 x 32 3010 0.022 16 x 20 2530 0.027 18 x 25 2740 0.026 13 x 35 2880 0.020 16 x 36 3510 0.019 13 x 20 1900 0.035 13 x 25 2230 0.027 13 x 30 2650 0.024 13 x 40 3350 0.017 16 x 40 3710 0.016 16 x 20 2530 0.027 16 x 25 2930 0.021 18 x 32 3635 0.021 18 x 20 2860 0.026 18 x 36 3680 0.017 18 x 40 3800 0.014 13 x 35 2880 0.020 16 x 32 3450 0.017 18 x 20 2860 0.026 18 x 25 3140 0.019 13 x 40 3350 0.017 16 x 36 3610 0.015 16 x 25 2930 0.021 18 x 32 4170 0.015 16 x 32 3450 0.017 16 x 40 4080 0.013 18 x 25 3140 0.019 18 x 36 4220 0.014 3900 18 x 32 4170 0.015 18 x 40 4280 0.012 4700 18 x 36 4220 0.014 5600 18 x 40 4280 0.012 2700 3300 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. ESR: 100KHz / 20°C (Ω Max.) 75 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 63 (79) SIZE 100 (125) SIZE RIPPLE ESR 5 x 11 55 2.30 6.3 x 11 115 1.20 8 x 11 232 0.63 39 8 x 15 300 0.45 47 10 x 12 288 0.43 8 x 20 362 0.33 10 x 15 357 0.31 RIPPLE ESR 6.8 15 5 x 11 55 2.30 27 33 56 6.3 x 11 8 x 11 115 232 1.20 0.63 68 82 8 x 15 300 0.45 10 x 19.5 466 0.21 10 x 12 288 0.43 13 x 15 466 0.23 10 x 25 531 0.20 100 120 8 x 20 362 0.33 10 x 30 663 0.15 10 x 15 357 0.31 13 x 20 690 0.16 16 x 16 795 0.14 10 x 19.5 466 0.21 13 x 25 784 0.12 13 x 15 466 0.23 18 x 15 920 0.12 10 x 25 531 0.20 13 x 30 905 0.10 16 x 20 1040 0.091 150 180 220 270 330 390 470 10 x 30 663 0.15 13 x 35 1050 0.083 13 x 20 690 0.16 16 x 25 1250 0.073 16 x 16 795 0.14 13 x 25 784 0.12 13 x 40 1180 0.071 18 x 20 1240 0.08 18 x 16 920 0.12 16 x 32 1570 0.054 18 x 25 1490 0.057 13 x 30 905 0.10 16 x 36 1790 0.045 16 x 20 1040 0.091 18 x 32 1630 0.047 13 x 35 1050 0.083 16 x 40 2020 0.04 16 x 25 1250 0.073 13 x 40 1180 0.071 18 x 36 1790 0.04 18 x 20 1240 0.080 820 16 x 32 1570 0.054 18 x 40 2330 0.036 18 x 25 1490 0.057 1000 16 x 36 1790 0.045 18 x 32 1630 0.047 16 x 40 2020 0.,04 560 680 1200 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. ESR: 100KHz / 20°C (Ω Ma x .) Yageo corporation ELECTROLYTIC CAPACITORS Miniature Aluminum Electrolytic Capacitors SZ [ Ultra Low ESR ] 105°C Single-Ended Lead Aluminum Electrolytic Capacitors for High Frequency Applications Electrical Characteristics Operating Temperature Range : -40 ~ +105°C Rated Voltage Range : 6.3 ~ 16V Rated Capacitance Range : 470 ~ 3300µF Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C description DC Leakage Current (µA) : I = 0.03 CV Whichever is greater. (After Rated Voltage Applied for 2 Minutes) Used in switching regulator applications in computers, especially for high frequency. Dissipation Factor W V (V) : 6.3 10 16 D.F. (%) : 22 19 16 When nominal capacitance is over 1000μF, tan δ shall be added 0.02 to the listed value with increase of every 1000μF. Low impedance and ESR, high permissible ripple current at high frequency and higher operating temperature (-40°C to +105°C). High Temperature Load Life at 105°C for 2000 Hours W V (V) : Rated Voltage (V) Impedance: Z - 25°C / Z + 20°C Z - 40°C / Z + 20°C MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient FREQUENCY (Hz) 120 1K FACTOR 0.50 0.80 10K 100K ≤ 0.90 1.00 Temperature Coefficient TEMPERATURE (°C) 65 85 105 FACTOR 2.10 1.70 1.00 6.3 2 3 10 2 3 16 2 3 Endurance: After applying rated voltage with ripple current for 2000 hours at 105°C, the capacitors shall meet the following requirements. (a) Capacitance Change : Within ±25% of Initial Value (b) Dissipation Factor : Not more than 200% of Specified Value (c) Leakage Current : Not more than the Specified Value diagram of dimensions Dimensions: mm Rubber Stand-off Vinyl Sleeve (P.V.C) Vinyl Sleeve (P.V.C) Rubber End Seal Rubber End Seal F±0.5 F±0.5 L 15Min. 5Min. D±0.5 L L ≤ 16 L + 1.5Max. L > 16 L + 2Max. Dø = 8 & 10 L + 2.5Max. 15Min. 5Min. Dø F dø 4.0 1.5 0.45 5.0 2.0 0.5 6.3 2.5 8.0 3.5 10.0 5.0 0.6 12.0 D±0.5 Dø < 20 Dø + 0.5 Dø ≥ 20 Dø + 1 13.0 16.0 7.5 18.0 22.0 10.0 0.8 77 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) 6.3 (8) SIZE RIPPLE ESR 10 (13) SIZE RIPPLE ESR 470 680 820 8 x 11 8 x 11 1140 1200 8 x 15 1490 28 1500 10 x 12 1540 26 8 x 20 1870 21 10 x 15 2000 19 2200 10 x 19.5 2550 16 3300 10 x 22 2800 12 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. ESR: 100KHz / 20°C (mΩ Max.) 1140 36 16 (20) SIZE RIPPLE ESR 8 x 11 1140 36 8 x 15 1490 28 10 x 12 1540 26 36 1000 1800 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 8 x 15 1490 28 8 x 20 1870 21 10 x 12 1540 26 10 x 15 2000 19 8 x 20 1870 21 10 x 19.5 2550 16 10 x 15 2000 19 10 x 19.5 2550 16 10 x 22 2800 12 10 x 22 2800 12 Yageo corporation ELECTROLYTIC CAPACITORS Large Can Aluminum Electrolytic Capacitors LH [ For 85°C, 2000 Hours Miniature ] For Printed Circuit Board High-Performance Aluminum Electrolytic Power Supply Input and Output Filter Capacitors ELECTRICAL CHARACTERISTICS Operating Temperature Range -40 to +85°C -25 to +85°C Rated Voltage Range 6.3 ~ 100V 160 to 450VDC Capacitance Tolerance 820 ~ 120000μF 56 ~ 2200μF Leakage Current I = 0.02CV or 3mA Whichever is smaller. (After 5 Minutes Application of DC Working Voltage at 20°C) Dissipation Factor (tanδ) Description Rate Voltage (V) 6.3 10 16 25 35 50 D.F. (%) 55 55 45 35 30 60 20 Ideally sutiable for using in switching power supplies and other industrial / commerical applications Z(-25°C) / Z(20°C) 4 3 3 2 2 4 8 Z(-40°C) / Z(20°C) 15 10 8 6 5 - - 60 120 1K 50~63 15 Endurance : 85°C, 2000 Hours Endurance 35 25 Rate Voltage (V) MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient 6.3~16 25 63-100 160-400 450 80~10 160~400 450 After applying rated voltage with rated ripple current for 2000 hours at 85°C, the capacitor shall meet the following requirements. FREQUENCY (Hz) 50 6.3~100V 0.88 0.90 1.00 1.15 1.16 160~250V 0.75 0.78 1.00 1.16 1.23 350~450V 0.74 0.76 1.00 1.10 1.15 (a) Capacitance Change: Within 20% of the Initial Value 10K (b) Dissipation Factor: 200% or Less of Initial Specified Value (c) Leakage Current: Initial Specified Value or Less Shelf Life After placed at 85°C without voltage applied for 1000 hours, the capacitor shall meet the same requirement as Endurance. diagram of dimensions Unit: mm Location of P.C.B. Holes Vinyl Sleeve 10±0.5 0.9±0.1 10±0.5 Botton Plate 3.0 5.8±1.0 2mm x 2 1.5+0.2/-0.1 Negative 0.8+0.2/-0.1 Safety Device L+2 Max. 5.81 D± 1 79 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 6.3 (8) SIZE 25 (32) SIZE RIPPLE 5600 22 x 25 2.20 6800 22 x 30 2.40 25 x 25 2.45 22 x 35 2.70 25 x 25 2.75 RIPPLE 10 (13) SIZE RIPPLE 8200 22 x 25 10000 12000 15000 18000 22000 27000 33000 16 (20) SIZE 22 x 25 22 x 25 2.44 2.40 RIPPLE 2.60 22 x 30 2.70 22 x 40 3.10 25 x 25 2.75 25 x 30 3.15 30 x 25 3.20 22 x 30 2.90 22 x 45 3.50 25 x 25 2.95 25 x 35 3.45 30 x 30 3.50 35 x 25 3.55 22 x 30 2.75 22 x 35 3.30 22 x 50 4.00 25 x 25 2.75 25 x 30 3.45 25 x 40 3.95 30 x 25 3.50 30 x 35 4.00 35 x 30 4.05 22 x 30 2.60 22 x 35 3.15 22 x 40 3.70 25 x 45 4.45 25 x 25 2.62 25 x 25 3.05 25 x 35 3.75 30 x 35 4.45 30 x 30 3.80 35 x 30 4.60 22 x 30 3.06 22 x 40 3.55 22 x 50 4.35 30 x 40 5.20 25 x 25 3.07 25 x 30 3.50 25 x 40 4.30 35 x 35 5.15 30 x 25 3.55 30 x 30 4.25 30 x 45 5.95 35 x 25 4.20 35 x 40 5.90 22 x 35 3.49 22 x 45 4.05 25 x 45 4.70 30 x 50 6.70 25 x 30 3.52 25 x 35 4.00 30 x 35 4.65 35 x 45 6.75 30 x 25 3.57 30 x 30 4.05 35 x 30 4.65 22 x 40 3.97 22 x 50 4.60 30 x 40 5.35 35 x 50 7.55 25 x 35 4.02 25 x 40 4.55 35 x 30 5.40 30 x 30 4.05 30 x 30 4.50 35 x 25 4.10 35 x 25 4.50 Note: 1. Ripple Current: (A/rms) 85°C, 120Hz 80 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) 6.3 (8) SIZE RIPPLE 10 (13) SIZE RIPPLE 16 (20) SIZE RIPPLE 22 x 50 4.56 25 x 45 5.10 30 x 45 6.00 25 x 40 4.50 30 x 35 5.05 35 x 35 5.95 30 x 30 4.46 35 x 30 5.05 35 x 25 4.51 25 x 45 5.09 25 x 50 5.75 30 x 50 6.80 30 x 35 5.06 30 x 40 5.70 35 x 40 6.75 35 x 30 5.03 35 x 30 5.65 25 x 50 5.71 30 x 45 6.45 35 x 45 7.60 30 x 40 5.70 35 x 35 6.40 35 x 30 5.75 30 x 45 6.48 30 x 50 7.05 35 x 50 8.00 35 x 35 6.42 35 x 40 7.10 30 x 50 7.32 35 x 50 7.50 35 x 40 7.29 100000 35 x 45 8.31 120000 35 x 50 8.60 39000 47000 56000 68000 82000 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) Note: 1. Ripple Current: (A/rms) 85°C, 120Hz 25 (32) SIZE RIPPLE 81 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 35 (44) SIZE 80 (100) SIZE RIPPLE 1200 22 x 25 1.65 1500 22 x 30 1.90 25 x 25 1.90 22 x 35 2.20 25 x 30 2.20 30 x 25 2.20 RIPPLE 50 (63) SIZE RIPPLE 1800 22 x 25 2200 22 x 25 2700 3300 3900 4700 5600 63 (79) SIZE 22 x 25 2.20 1.90 RIPPLE 1.85 22 x 30 2.30 22 x 40 2.45 25 x 25 2.30 25 x 30 2.45 30 x 25 2.50 22 x 30 2.10 22 x 35 2.45 22 x 45 2.80 25 x 25 2.20 25 x 30 2.45 25 x 35 2.80 30 x 25 2.50 30 x 30 2.85 35 x 25 2.85 22 x 30 2.35 22 x 40 2.60 22 x 50 3.15 25 x 25 2.35 25 x 30 2.65 25 x 40 3.20 30 x 25 2.70 30 x 30 3.20 35 x 25 3.20 22 x 35 2.65 22 x 45 2.95 25 x 45 3.60 25 x 30 2.65 25 x 35 2.95 30 x 35 3.60 30 x 25 2.65 30 x 30 3.00 35 x 30 3.60 22 x 30 2.40 22 x 40 3.00 22 x 50 3.40 25 x 50 4.05 25 x 25 2.40 25 x 35 3.00 25 x 40 3.35 30 x 40 4.05 30 x 25 2.95 30 x 30 3.35 35 x 35 4.10 35 x 25 3.40 22 x 35 2.75 22 x 45 3.35 25 x 45 3.70 30 x 45 4.55 25 x 25 2.75 25 x 40 3.35 30 x 35 3.75 35 x 35 4.50 30 x 30 3.35 35 x 30 3.75 35 x 25 3.40 Note: 1. Ripple Current: (A/rms) 85°C, 120Hz 82 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) 6800 8200 10000 12000 15000 18000 22000 27000 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 35 (44) SIZE RIPPLE 50 (63) SIZE RIPPLE 63 (79) SIZE RIPPLE 80 (100) SIZE RIPPLE 22 x 40 2.85 22 x 50 3.80 30 x 40 4.25 30 x 50 5.15 25 x 30 2.85 25 x 40 3.80 35 x 30 4.20 35 x 40 5.15 30 x 25 2.90 30 x 30 3.80 30 x 35 3.85 35 x 30 3.85 35 x 45 5.85 35 x 50 6.60 22 x 45 3.15 25 x 50 4.35 30 x 45 4.80 25 x 35 3.10 30 x 40 4.35 35 x 35 4.80 30 x 30 3.15 35 x 30 4.40 22 x 50 3.55 30 x 45 5.00 30 x 50 5.50 25 x 40 3.50 35 x 35 4.95 35 x 40 5.45 30 x 30 3.45 35 x 25 3.40 25 x 45 3.95 30 x 50 5.60 35 x 45 6.20 30 x 35 4.00 35 x 40 5.55 35 x 30 4.05 25 x 50 4.95 35 x 45 6.45 30 x 40 4.95 35 x 35 5.00 30 x 45 5.50 35 x 50 6.70 35 x 40 5.55 30 x 50 6.00 35 x 45 6.05 35 x 50 6.90 Note: 1. Ripple Current: (A/rms) 85°C, 120Hz 83 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 100 (125) SIZE 180 (225) SIZE RIPPLE 200 (250) SIZE RIPPLE 180 22 x 20 1.00 22 x 25 0.95 220 22 x 25 1.10 22 x 25 1.10 22 x 25 1.25 22 x 25 1.25 25 x 20 1.25 22 x 30 1.25 25 x 25 1.25 RIPPLE 270 22 x 25 330 390 470 560 680 820 1000 160 (200) SIZE 22 x 25 1.85 RIPPLE 1.15 22 x 25 1.40 22 x 25 1.40 22 x 25 1.45 25 x 20 1.35 22 x 30 1.40 22 x 30 1.45 25 x 25 1.40 25 x 25 1.45 22 x 30 1.55 22 x 30 1.60 22 x 30 1.60 25 x 25 1.55 25 x 25 1.60 25 x 25 1.55 30 x 25 1.50 22 x 30 1.75 22 x 35 1.80 22 x 35 1.80 25 x 25 1.75 25 x 30 1.80 25 x 30 1.80 30 x 25 1.70 30 x 25 1.80 30 x 25 1.80 22 x 30 1.95 22 x 35 2.00 22 x 40 2.00 25 x 30 1.95 22 x 40 2.00 25 x 35 2.00 30 x 25 1.90 25 x 30 1.95 30 x 25 2.00 30 x 25 2.00 22 x 40 2.20 22 x 45 2.25 22 x 45 2.35 25 x 30 2.20 25 x 35 2.20 25 x 35 2.30 30 x 25 2.15 30 x 30 2.20 30 x 30 2.30 35 x 25 2.20 35 x 25 2.30 22 x 45 2.50 22 x 50 2.55 25 x 40 2.60 25 x 35 2.55 25 x 40 2.55 25 x 45 2.60 30 x 30 2.50 30 x 30 2.60 30 x 30 2.60 35 x 25 2.50 30 x 35 2.60 30 x 35 2.60 35 x 25 2.60 35 x 30 2.60 22 x 30 2.10 22 x 50 2.85 25 x 45 2.85 25 x 45 3.00 25 x 25 2.10 25 x 40 2.80 30 x 35 2.85 25 x 50 3.00 30 x 35 2.80 35 x 30 2.90 30 x 35 3.05 35 x 25 2.80 30 x 40 3.05 35 x 30 3.00 Note: 1. Ripple Current: (A/rms) 85°C, 120Hz 84 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) 1200 1500 1800 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 100 (125) SIZE RIPPLE 160 (200) SIZE RIPPLE 180 (225) SIZE RIPPLE 200 (250) SIZE RIPPLE 22 x 35 2.40 25 x 45 3.15 30 x 40 3.25 25 x 50 3.30 25 x 30 2.45 30 x 35 3.15 35 x 30 3.30 30 x 40 3.30 35 x 30 3.20 35 x 35 3.30 30 x 45 3.30 35 x 30 3.30 35 x 35 3.30 22 x 40 2.70 30 x 45 3.75 30 x 45 3.85 30 x 45 3.80 25 x 30 2.75 35 x 30 3.70 35 x 35 3.80 30 x 50 3.80 30 x 25 2.75 35 x 35 3.70 35 x 40 3.80 35 x 35 3.80 35 x 40 3.80 22 x 45 3.10 30 x 50 4.20 35 x 40 4.30 35 x 40 4.35 25 x 35 3.15 35 x 40 4.20 35 x 45 4.30 35 x 45 4.35 30 x 30 3.15 35 x 25 3.15 22 x 50 3.50 35 x 40 4.60 35 x 45 4.90 35 x 45 4.95 25 x 40 3.55 35 x 45 4.80 35 x 50 4.90 35 x 50 4.95 30 x 30 3.55 35 x 25 3.60 25 x 45 4.10 35 x 50 5.45 30 x 35 4.05 35 x 30 4.05 25 x 50 4.50 30 x 40 4.55 35 x 30 4.50 30 x 45 5.15 35 x 35 5.10 4700 35 x 40 5.75 5600 35 x 50 6.20 2200 2700 3300 3900 Note: 1. Ripple Current: (A/rms) 85°C, 120Hz 85 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) 250 (300) SIZE RIPPLE 350 (400) SIZE RIPPLE 400 (450) SIZE RIPPLE 47 56 68 22 x 20 82 100 120 150 180 220 270 330 390 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 22 x 20 22 x 25 0.78 0.90 0.55 450 (500) SIZE RIPPLE 22 x 25 0.50 22 x 20 0.55 22 x 25 0.65 22 x 25 0.60 22 x 30 0.70 25 x 20 0.60 25 x 25 0.70 22 x 25 0.65 22 x 25 0.80 22 x 30 0.80 25 x 20 0.65 25 x 20 0.80 25 x 25 0.80 22 x 30 0.90 22 x 30 0.90 22 x 35 0.95 25 x 20 0.90 25 x 25 0.90 25 x 30 0.95 30 x 25 0.95 22 x 30 1.00 22 x 35 1.05 22 x 40 1.05 25 x 25 1.00 25 x 25 1.05 25 x 30 1.05 30 x 25 1.05 22 x 35 1.15 22 x 35 1.15 22 x 45 1.20 25 x 30 1.15 25 x 30 1.15 25 x 35 1.20 30 x 25 1.15 30 x 25 1.15 30 x 30 1.20 22 x 25 1.05 22 x 40 1.30 22 x 45 1.30 25 x 40 1.35 25 x 20 1.00 25 x 30 1.25 25 x 35 1.30 30 x 35 1.35 30 x 25 1.25 30 x 30 1.35 35 x 25 1.35 22 x 30 1.15 22 x 45 1.45 22 x 50 1.50 25 x 50 1.55 22 x 35 1.15 25 x 35 1.45 25 x 40 1.50 30 x 40 1.55 25 x 25 1.15 30 x 30 1.45 30 x 30 1.50 35 x 30 1.55 35 x 25 1.45 35 x 25 1.50 22 x 30 1.30 25 x 40 1.65 25 x 40 1.65 30 x 45 1.75 25 x 25 1.30 30 x 35 1.65 30 x 35 1.65 35 x 35 1.70 35 x 25 1.65 35 x 30 1.65 22 x 30 1.50 25 x 50 1.80 25 x 50 1.90 30 x 50 2.00 25 x 25 1.50 30 x 40 1.80 30 x 40 1.90 35 x 40 2.00 30 x 25 1.50 35 x 30 1.80 35 x 30 1.85 22 x 35 1.65 30 x 40 2.00 30 x 45 2.15 35 x 45 2.25 25 x 35 1.65 35 x 30 2.00 35 x 35 2.10 30 x 25 1.65 Note: 1. Ripple Current: (A/rms) 85°C, 120Hz 86 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 250 (300) SIZE RIPPLE 350 (400) SIZE RIPPLE 400 (450) SIZE RIPPLE 450 (500) SIZE RIPPLE 22 x 40 1.85 30 x 45 2.25 30 x 50 2.40 35 x 50 2.50 25 x 35 1.85 35 x 35 2.25 35 x 40 2.40 30 x 30 1.90 35 x 25 1.90 22 x 45 2.10 35 x 40 2.50 35 x 45 2.70 25 x 40 2.10 30 x 30 2.10 35 x 25 2.10 25 x 45 2.45 35 x 45 2.90 35 x 50 2.90 35 x 60 2.90 30 x 35 2.45 35 x 25 2.45 30 x 45 2.75 35 x 30 2.75 30 x 45 3.30 35 x 35 3.30 1200 35 x 40 3.55 1500 35 x 45 4.05 470 560 680 820 1000 Note: 1. Ripple Current: (A/rms) 85°C, 120Hz Yageo corporation ELECTROLYTIC CAPACITORS LG [ For 105°C, 2000 Hours General ] Large Can Aluminum Electrolytic Capacitors For Printed Circuit Board High-Performance Aluminum Electrolytic Power Supply Input and Output Filter Capacitors ELECTRICAL CHARACTERISTICS Operating Temperature Range -40 to +105°C -25 to +105°C Rated Voltage Range 6.3 to 100VDC 160 to 450VDC Capacitance Range 560 ~ 82000μF 47 ~ 2200μF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current I = 0.02CV, L = 20m/m, I = 0.03CV or 3mA Whichever is smaller. (After 5 Minutes Application of DC Working Voltage at 20°C) I = Leakage Current (μA), C = Nominal Capacitance (μF),V = Rated Voltage (V) Dissipation Factor (tanδ) Rate Voltage (V) 6.3 10 16 25 35 50 D.F. (%) 60 55 55 45 35 30 25 15 20 Low Temperature Rated Voltage (V) Characteristics Z(-25°C) / Z(20°C) 4 (120Hz) Z(-40°C) / Z(20°C) 15 Endurance After applying rated voltage with rated ripple current for 2000 hours at Shelf Life 6.3~16 25 63-100 160-400 450 35 50~63 80~10 160~400 450 3 3 2 2 4 8 10 8 6 5 - - Description Endurance : 105°C 2000 hours, higher temperature than LH. Ideally suitable for using in switching power supplies and other industrial / commercial applications. MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient 105°C, the capacitor shall meet the following requirements. FREQUENCY (Hz) 50 60 120 1K 10K (a) Capacitance Change: ≤ ±20% of the Initial Value (b) Dissipation Factor: ≤ 200% of the Initial Specified Value 6.3~100V 0.88 0.90 1.00 1.15 1.16 160~250V 0.85 0.88 1.00 1.15 1.20 (c) Leakage Current: ≤ the Initial Specified Value 315~450V 0.88 0.90 1.00 1.10 1.15 After placed at 105°C without voltage applied for 1000 hours, the capacitor shall meet the same requirement as Endurance. diagram of dimensions Unit: mm Location of P.C.B. Holes Vinyl Sleeve 10±0.5 0.9±0.1 Botton Plate 10±0.5 Negative L+2 Max. 5.8±0.1 D±1 3.0 Safety Device 5.8±1.0 2mm x 2 1.5+0.2 /-0.1 0.8+0.2 /-0.1 88 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) D x L: mm Rated Voltage W V (SURGE VOLTAGE W V) 6.3 (8) SIZE 25 (32) SIZE RIPPLE 4700 22 x 25 1.50 5600 22 x 30 1.65 25 x 25 1.65 RIPPLE 10 (13) SIZE RIPPLE 6800 22 x 25 8200 10000 12000 15000 18000 22000 27000 33000 39000 47000 56000 68000 82000 16 (20) SIZE 22 x 25 1.55 RIPPLE 1.55 22 x 30 1.85 25 x 25 1.85 2.10 22 x 30 1.70 22 x 35 25 x 25 1.70 25 x 30 2.10 30 x 25 2.15 22 x 25 1.55 22 x 30 1.95 22 x 40 2.40 25 x 25 1.55 25 x 25 1.95 25 x 35 2.40 22 x 30 1.75 30 x 30 2.40 35 x 25 2.40 22 x 35 2.20 22 x 45 2.70 25 x 30 2.25 25 x 40 2.75 30 x 25 2.30 30 x 30 2.70 35 x 25 2.75 22 x 30 1.70 22 x 30 1.90 22 x 40 2.55 25 x 45 3.15 25 x 25 1.70 25 x 25 1.90 25 x 35 2.60 30 x 35 3.15 35 x 30 3.25 30 x 30 2.60 35 x 25 2.65 22 x 30 1.95 22 x 35 2.20 22 x 45 2.90 25 x 50 3.55 25 x 25 1.95 25 x 30 2.25 25 x 40 2.90 30 x 40 3.55 30 x 30 2.90 35 x 35 3.55 35 x 25 2.95 22 x 35 2.25 22 x 40 2.50 25 x 45 3.30 30 x 45 4.05 25 x 30 2.25 25 x 35 2.55 30 x 35 3.30 35 x 35 3.80 30 x 25 2.25 30 x 25 2.45 35 x 30 3.30 22 x 40 2.55 22 x 50 2.95 25 x 50 3.80 35 x 45 4.70 25 x 35 2.55 25 x 40 2.90 30 x 40 3.75 35 x 30 3.75 35 x 50 5.40 30 x 30 2.55 30 x 30 2.85 35 x 25 2.55 35 x 25 2.80 22 x 45 2.90 25 x 45 3.30 30 x 45 4.30 25 x 40 2.95 30 x 35 3.30 35 x 35 4.25 30 x 30 2.90 35 x 30 3.30 35 x 25 2.95 25 x 50 3.25 25 x 50 3.70 30 x 50 4.80 30 x 35 3.25 30 x 40 3.70 35 x 40 4.80 35 x 30 3.30 35 x 30 3.65 35 x 45 5.45 25 x 50 3.70 30 x 45 4.20 30 x 40 3.70 35 x 35 3.80 30 x 45 4.15 30 x 50 4.65 35 x 35 4.10 35 x 40 4.65 35 x 50 5.50 30 x 50 4.70 35 x 40 4.70 35 x 45 5.30 Note: 1. Ripple Current: (A/rms) 105°C, 120Hz 89 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 35 (44) SIZE 80 (100) SIZE RIPPLE 820 22 x 25 1.10 1000 22 x 30 1.20 25 x 25 1.20 22 x 30 1.40 25 x 25 1.40 RIPPLE 50 (63) SIZE RIPPLE 1200 22 x 25 1500 1800 22 x 25 2200 2700 3300 3900 4700 63 (79) SIZE 22 x 25 1.40 1.30 RIPPLE 1.20 22 x 30 1.30 22 x 35 1.60 25 x 25 1.30 25 x 30 1.60 30 x 25 1.65 22 x 30 1.50 22 x 40 1.80 25 x 25 1.50 25 x 35 1.85 30 x 25 1.80 22 x 30 1.55 22 x 35 1.70 22 x 45 2.05 25 x 25 1.55 25 x 30 1.75 25 x 35 2.00 30 x 25 1.80 30 x 30 2.05 35 x 25 2.05 22 x 30 1.70 22 x 40 2.00 25 x 45 2.35 25 x 25 1.70 25 x 35 2.00 30 x 35 2.35 30 x 25 1.95 35 x 30 2.35 22 x 35 1.95 22 x 50 2.30 25 x 50 2.70 25 x 30 1.85 25 x 40 2.30 30 x 40 2.70 30 x 30 2.25 35 x 30 2.55 35 x 25 2.10 22 x 30 1.55 22 x 40 2.15 25 x 45 2.55 30 x 45 3.00 25 x 25 1.55 25 x 35 2.20 30 x 35 2.55 35 x 35 3.00 30 x 25 1.95 35 x 30 2.55 22 x 35 1.80 22 x 45 2.45 25 x 50 2.85 30 x 50 3.40 25 x 25 1.80 25 x 40 2.45 30 x 40 2.85 35 x 40 3.40 30 x 30 2.45 35 x 30 2.80 35 x 25 2.50 Note: 1. Ripple Current: (A/rms) 105°C, 120Hz 90 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) 5600 6800 35 (44) SIZE RIPPLE 50 (63) SIZE RIPPLE 63 (79) SIZE RIPPLE 80 (100) SIZE RIPPLE 22 x 35 19.5 22 x 50 2.75 30 x 45 3.20 35 x 45 3.80 25 x 30 1.95 25 x 40 2.70 35 x 35 3.20 30 x 25 2.00 30 x 35 2.75 35 x 30 2.75 35 x 50 3.90 35 x 60 4.00 22 x 40 2.20 25 x 50 3.30 30 x 50 3.65 25 x 35 2.25 30 x 40 3.30 35 x 40 3.65 30 x 30 2.30 35 x 30 3.25 35 x 25 2.35 22 x 50 2.55 30 x 45 3.60 35 x 45 3.90 25 x 40 2.50 35 x 35 3.55 30 x 30 2.75 35 x 25 2.75 25 x 45 2.85 30 x 40 3.45 35 x 50 4.40 30 x 35 2.90 35 x 50 4.05 35 x 30 2.95 35 x 40 4.00 25 x 50 3.25 35 x 45 4.55 30 x 40 3.25 35 x 30 3.15 30 x 45 3.70 35 x 35 3.65 18000 35 x 40 4.35 22000 35 x 50 4.90 8200 10000 12000 15000 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) Note: 1. Ripple Current: (A/rms) 105°C, 120Hz 91 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) 100 (125) SIZE RIPPLE 160 (200) SIZE RIPPLE 180 (225) SIZE RIPPLE 150 180 220 22 x 20 270 22 x 25 330 390 470 560 680 820 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 22 x 25 22 x 25 1.05 1.20 0.80 1.00 200 (250) SIZE RIPPLE 22 x 20 0.65 22 x 20 0.75 22 x 20 0.70 22 x 25 0.85 22 x 25 0.80 25 x 20 0.80 22 x 25 0.95 22 x 25 0.85 25 x 20 0.90 25 x 25 0.85 22 x 25 1.20 22 x 25 1.20 22 x 30 1.20 25 x 20 1.15 22 x 30 1.10 25 x 25 1.20 25 x 25 1.10 22 x 30 1.30 22 x 30 1.30 22 x 30 1.30 25 x 25 1.30 25 x 25 1.30 22 x 35 1.30 25 x 30 1.30 30 x 25 1.30 22 x 30 1.30 22 x 30 1.30 22 x 35 1.40 22 x 35 1.40 22 x 35 1.35 22 x 40 1.40 25 x 25 1.40 25 x 30 1.40 25 x 30 1.40 30 x 25 1.40 30 x 25 1.50 22 x 40 1.50 22 x 40 1.50 22 x 45 1.55 25 x 30 1.50 25 x 35 1.55 25 x 35 1.55 30 x 25 1.50 30 x 25 1.50 30 x 30 1.55 22 x 45 1.70 22 x 45 1.70 22 x 50 1.75 25 x 35 1.70 22 x 50 1.70 25 x 40 1.75 30 x 25 1.70 25 x 35 1.70 30 x 30 1.75 25 x 40 1.75 35 x 25 1.70 30 x 30 1.70 35 x 25 1.70 22 x 30 1.30 22 x 50 1.95 22 x 50 1.95 25 x 50 2.05 25 x 25 1.33 25 x 40 2.00 25 x 40 2.00 30 x 35 2.00 30 x 30 2.00 25 x 45 2.00 35 x 30 2.05 35 x 25 1.90 30 x 35 2.00 35 x 25 1.90 Note: 1. Ripple Current: (A/rms) 105°C, 120Hz 92 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) 1000 1200 1500 100 (125) SIZE RIPPLE 160 (200) SIZE RIPPLE 180 (225) SIZE RIPPLE 200 (250) SIZE RIPPLE 22 x 35 1.50 25 x 45 2.20 25 x 45 2.20 30 x 40 2.30 25 x 30 1.50 30 x 35 2.20 25 x 50 2.20 30 x 45 2.30 35 x 30 2.20 30 x 35 2.25 35 x 30 2.30 30 x 40 2.25 35 x 35 2.30 35 x 30 2.25 22 x 40 1.70 25 x 50 2.45 25 x 50 2.45 30 x 50 2.60 25 x 35 1.70 30 x 40 2.45 30 x 40 2.45 35 x 40 2.65 30 x 25 1.70 35 x 30 2.45 30 x 45 2.50 35 x 35 2.50 35 x 45 3.10 35 x 50 3.15 35 x 50 4.80 22 x 45 1.95 30 x 45 2.80 30 x 45 2.80 25 x 40 2.00 35 x 35 2.80 30 x 50 2.90 30 x 30 1.95 35 x 40 2.90 35 x 25 2.00 25 x 45 2.20 30 x 50 3.30 30 x 50 3.30 30 x 35 2.50 35 x 45 3.30 35 x 50 3.30 35 x 30 2.45 25 x 50 2.55 35 x 50 3.75 35 x 50 3.60 30 x 40 2.70 35 x 30 2.55 30 x 45 2.90 35 x 35 2.85 30 x 50 3.25 35 x 40 3.25 3900 35 x 45 3.70 4700 35 x 50 3.80 1800 2200 2700 3300 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) Note: 1. Ripple Current: (A/rms) 105°C, 120Hz 93 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 250 (300) SIZE RIPPLE 350 (400) SIZE RIPPLE 47 400 (450) SIZE RIPPLE 450 (500) SIZE RIPPLE 22 x 20 0.35 22 x 25 0.36 56 22 x 20 0.40 22 x 20 0.40 22 x 25 0.40 68 22 x 25 0.45 22 x 25 0.50 22 x 30 0.50 25 x 20 0.50 25 x 25 0.50 82 100 120 150 180 220 270 22 x 25 22 x 20 22 x 25 0.56 0.60 0.65 22 x 25 0.55 22 x 30 0.60 22 x 35 0.55 25 x 20 0.50 25 x 25 0.65 25 x 30 0.55 30 x 25 0.55 22 x 30 0.70 22 x 35 0.65 22 x 40 0.65 25 x 25 0.70 25 x 25 0.65 25 x 30 0.60 25 x 30 0.65 30 x 25 0.65 22 x 35 0.75 22 x 35 0.70 22 x 45 0.70 25 x 30 0.75 25 x 30 0.70 25 x 35 0.70 30 x 25 0.75 30 x 25 0.75 30 x 30 0.70 35 x 25 0.70 22 x 40 0.80 22 x 40 0.80 22 x 50 0.80 25 x 30 0.80 25 x 30 0.85 25 x 40 0.80 30 x 25 0.85 25 x 35 0.85 30 x 30 0.75 30 x 30 0.85 35 x 25 0.75 35 x 25 0.80 22 x 25 0.80 22 x 45 0.90 22 x 50 0.95 25 x 45 0.85 25 x 20 0.75 25 x 35 0.90 25 x 40 0.95 30 x 35 0.85 30 x 30 0.90 30 x 30 0.90 35 x 30 0.85 22 x 30 0.95 22 x 50 1.05 25 x 45 1.05 25 x 50 1.00 25 x 25 0.95 25 x 40 1.05 30 x 30 1.05 30 x 40 1.00 30 x 30 1.00 30 x 35 1.05 35 x 30 1.00 35 x 25 1.05 35 x 30 1.10 22 x 35 1.15 25 x 45 1.20 25 x 50 1.20 30 x 45 1.15 25 x 30 1.15 30 x 35 1.20 30 x 40 1.20 35 x 35 1.15 30 x 25 1.15 35 x 30 1.20 35 x 35 1.20 Note: 1. Ripple Current: (A/rms) 105°C, 120Hz 94 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) 330 390 470 560 680 820 1000 1500 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 250 (300) SIZE RIPPLE 350 (400) SIZE RIPPLE 400 (450) SIZE RIPPLE 450 (500) SIZE RIPPLE 22 x 40 1.25 30 x 40 1.35 30 x 45 1.40 30 x 45 1.20 25 x 30 1.20 30 x 45 1.35 35 x 35 1.35 30 x 50 1.40 30 x 25 1.25 35 x 35 1.35 35 x 40 1.40 22 x 45 1.50 30 x 45 1.50 30 x 50 1.55 35 x 45 1.55 25 x 35 1.50 35 x 35 1.50 35 x 40 1.55 30 x 30 1.50 22 x 50 1.55 35 x 40 1.70 30 x 50 1.75 35 x 40 1.47 25 x 40 1.55 35 x 40 1.75 35 x 45 1.70 30 x 30 1.55 35 x 45 1.75 35 x 50 1.70 35 x 25 1.55 35 x 50 1.75 25 x 45 1.80 30 x 62 1.90 35 x 60 2.10 30 x 35 1.80 35 x 50 1.90 35 x 30 1.80 25 x 50 1.95 35 x 50 1.88 30 x 40 2.00 35 x 60 2.15 35 x 35 2.00 30 x 45 2.15 35 x 35 2.10 30 x 45 2.10 35 x 40 2.30 35 x 50 3.63 Note: 1. Ripple Current: (A/rms) 105°C, 120Hz 35 x 45 35 x 50 1.90 2.10 Yageo corporation ELECTROLYTIC CAPACITORS LV [ For 105°C, 3000 Hours Long Life ] Large Can Aluminum Electrolytic Capacitors For Printed Circuit Board High-Performance Aluminum Electrolytic Power Supply Input and Output Filter Capacitors ELECTRICAL CHARACTERISTICS Operating Temperature Range -40 to +105°C -25 to +105°C Rated Voltage Range 10 to 100VDC 160 to 450VDC Nominal Capacitance Range 560 ~ 68000μF 270 ~ 2200μF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current 1 ≤ 0.02CV or 3mA Whichever is smaller (After Rated Voltage Applied for 5 Minutes) I = Leakage Current (μA), C = Nominal Capacitance (μF),V = Rated Voltage (V) Dissipation Factor (tanδ) Rate Voltage (V) 10 16 25 35 50 63 80 100 160 180~400 450 (20°C, 120Hz) D.F (%) 55 55 45 40 35 30 25 25 15 15 25 Dissipation Factor (tan δ) shall not exceed the values showed as above of standard rating Endurance After applying rated voltage with rated ripple current for 3000 hours at Features : 105°C 3000 hours, Longer life than LG, Snap-in terminal, High ripple current. Recommended Applications : Smoothing circuit, TV/ Monitor, Adapter, SMPS. 105°C, the capacitor shall meet the following requirement. MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient (a) Capacitance Change : Within ±20% of the Initial Value FREQUENCY (Hz) 50 60 120 400 COEFFICIENT 0.8 0.85 1.0 1.14 FREQUENCY (Hz) IK 2.4K 5K 10K COEFFICIENT 1.23 1.3 1.36 1.4 (b) Dissipation Factor : Not more than 200% of the Specified Value (c) Leakage current : Not more than the Specified Value Shelf Life Description After placed at 105°C without voltage applied for 1000 hours, the capacitor shall meet the same requirements as Endurance. diagram of dimensions Unit: mm Location of P.C.B. Holes Vinyl Sleeve Botton Plate 10±0.5 0.9±0.1 Negative 10±0.5 L+2 Max. 5.8±0.1 D±1 3.0 Safety Device 5.8±1.0 2mm x 2 1.5+0.2/-0.1 0.8+0.2/-0.1 96 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 10 (13) SIZE RIPPLE 16 (20) SIZE RIPPLE 25 (32) SIZE RIPPLE 35 (44) SIZE RIPPLE 50 (63) SIZE RIPPLE 1200 1500 22 x 25 1800 22 x 30 2200 2700 22 x 25 3300 22 x 30 3900 22 x 25 4700 22 x 30 5600 6800 8200 22 x 25 1.80 1.50 1.80 22 x 30 1.45 1.60 1.80 1.25 1.45 RIPPLE 22 x 25 1.25 22 x 30 1.45 25 x 25 1.45 22 x 35 1.60 25 x 30 1.60 22 x 30 1.60 22 x 40 1.89 25 x 25 1.60 25 x 30 1.80 30 x 25 1.85 22 x 35 1.80 22 x 45 2.06 25 x 30 1.80 25 x 35 2.00 30 x 30 2.08 22 x 40 2.05 25 x 40 2.32 25 x 30 1.95 30 x 30 2.30 30 x 25 2.01 35 x 25 2.35 22 x 45 2.27 25 x 45 2.55 25 x 35 2.20 30 x 35 2.55 30 x 30 2.29 35 x 30 2.63 22 x 35 2.23 22 x 50 2.50 25 x 50 2.83 25 x 25 2.10 25 x 40 2.42 30 x 40 2.86 30 x 30 2.40 35 x 30 2.80 35 x 25 2.45 22 x 30 1.95 22 x 40 2.41 25 x 45 2.70 30 x 45 3.18 25 x 25 1.95 25 x 30 2.30 30 x 35 2.70 35 x 35 3.15 30 x 25 2.37 35 x 30 2.78 22 x 35 2.20 22 x 45 2.68 30 x 40 3.06 30 x 50 3.50 25 x 30 2.20 25 x 35 2.60 35 x 30 3.00 35 x 40 3.50 30 x 30 2.70 35 x 45 3.90 22 x 30 2.05 22 x 40 2.47 22 x 50 3.02 30 x 45 3.38 25 x 25 2.05 25 x 35 2.50 25 x 40 2.93 35 x 35 3.35 30 x 25 2.45 30 x 30 2.90 35 x 25 2.96 Note: 1. Ripple Current: (A/rms) 105°C, 120Hz 63 (79) SIZE 97 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) 10000 12000 15000 18000 22000 10 (13) SIZE RIPPLE 16 (20) SIZE RIPPLE 25 (32) SIZE RIPPLE 35 (44) SIZE RIPPLE 50 (63) SIZE RIPPLE 22 x 25 1.80 22 x 35 2.45 22 x 45 2.75 25 x 45 3.20 30 x 50 3.50 25 x 30 2.45 25 x 40 2.80 30 x 35 3.20 35 x 40 3.70 30 x 30 2.75 35 x 30 3.30 35 x 50 4.20 22 x 30 2.05 22 x 40 2.73 22 x 50 3.13 25 x 50 3.64 25 x 25 2.05 25 x 30 2.60 25 x 45 3.22 30 x 40 3.67 30 x 25 2.68 30 x 35 3.19 35 x 30 3.60 35 x 25 3.10 22 x 35 2.45 22 x 45 2.99 25 x 50 3.43 30 x 45 4.04 25 x 30 2.45 25 x 35 2.90 30 x 40 3.47 35 x 35 4.00 30 x 25 2.55 30 x 30 3.02 35 x 30 3.40 22 x 40 2.94 22 x 50 3.43 30 x 45 3.94 35 x 40 4.60 25 x 30 2.80 25 x 40 3.33 35 x 35 3.90 30 x 30 3.11 30 x 30 3.30 35 x 25 3.37 35 x 50 5.10 22 x 45 3.24 25 x 45 3.70 30 x 50 4.30 25 x 35 3.15 30 x 35 3.70 35 x 40 4.30 30 x 30 3.28 35 x 30 3.81 35 x 25 3.37 25 x 40 3.50 30 x 40 4.15 35 x 45 4.85 30 x 35 3.67 35 x 35 4.27 35 x 30 3.78 25 x 45 4.00 30 x 50 4.65 30 x 40 4.20 35 x 40 4.65 35 x 30 4.08 25 x 50 4.45 35 x 45 5.25 30 x 45 4.67 35 x 35 4.63 47000 35 x 40 4.90 35 x 50 5.80 56000 35 x 45 5.50 68000 35 x 50 6.05 27000 33000 39000 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) Note: 1. Ripple Current: (A/rms) 105°C, 120Hz 63 (79) SIZE RIPPLE 98 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 80 (100) SIZE RIPPLE 100 (125) SIZE RIPPLE 160 (200) SIZE RIPPLE 180 (225) SIZE RIPPLE 220 200 (250) SIZE RIPPLE 22 x 25 0.85 270 22 x 25 0.85 22 x 25 0.85 22 x 30 1.00 330 22 x 30 1.00 22 x 30 1.10 22 x 30 1.15 25 x 25 1.15 390 470 560 22 x 25 680 820 1000 1200 1500 22 x 30 22 x 25 22 x 30 1.20 1.35 1.20 1.35 22 x 30 1.15 22 x 35 1.32 22 x 35 1.30 25 x 25 1.15 25 x 25 1.25 25 x 30 1.30 22 x 35 1.30 22 x 40 1.47 22 x 40 1.52 25 x 30 1.30 25 x 30 1.40 25 x 35 1.54 30 x 25 1.49 22 x 40 1.57 22 x 45 1.70 22 x 45 1.70 25 x 30 1.50 25 x 35 1.63 25 x 35 1.65 30 x 25 1.54 30 x 25 1.60 30 x 30 1.72 22 x 45 1.75 22 x 50 1.87 25 x 45 1.97 25 x 35 1.70 25 x 40 1.82 30 x 35 1.97 30 x 30 1.77 30 x 30 1.80 35 x 30 2.02 35 x 25 1.84 22 x 30 1.50 22 x 50 2.03 25 x 45 2.05 25 x 45 2.20 25 x 25 1.50 25 x 40 1.97 30 x 35 2.05 30 x 35 2.10 30 x 30 1.95 35 x 30 2.11 35 x 30 2.16 35 x 25 1.99 22 x 35 1.70 25 x 45 2.15 25 x 50 2.27 30 x 45 2.32 25 x 30 1.70 30 x 35 2.15 30 x 40 2.29 35 x 35 2.30 35 x 30 2.21 35 x 30 2.25 22 x 35 1.59 22 x 40 1.97 30 x 40 2.45 30 x 45 2.57 30 x 50 2.75 25 x 25 1.50 25 x 35 1.99 35 x 35 2.52 35 x 35 2.55 35 x 40 2.75 30 x 25 1.95 35 x 40 2.85 35 x 45 2.90 22 x 40 1.78 22 x 45 2.15 30 x 50 2.75 25 x 30 1.70 25 x 40 2.19 35 x 40 2.75 30 x 25 1.75 30 x 30 2.15 35 x 25 2.21 Note: 1. Ripple Current: (A/rms) 105°C, 120Hz 99 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) 1800 2200 2700 3300 3900 4700 5600 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 80 (100) SIZE RIPPLE 100 (125) SIZE RIPPLE 160 (200) SIZE RIPPLE 180 (225) SIZE RIPPLE 22 x 45 2.01 25 x 45 2.45 35 x 45 3.00 35 x 50 3.10 25 x 35 1.95 30 x 35 2.45 30 x 30 2.03 35 x 30 2.52 25 x 40 2.17 25 x 50 2.75 35 x 50 3.50 30 x 30 2.15 30 x 40 2.75 35 x 25 2.19 35 x 35 2.86 25 x 45 2.45 30 x 45 3.08 30 x 35 2.45 35 x 35 3.05 35 x 30 2.52 30 x 40 2.75 30 x 50 3.45 35 x 35 2.83 35 x 40 3.45 30 x 45 3.13 35 x 45 3.90 35 x 35 3.10 35 x 40 3.40 35 x 45 3.90 35 x 50 4.30 35 x 50 3.80 Note: 1. Ripple Current: (A/rms) 105°C, 120Hz 200 (250) SIZE RIPPLE 100 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) 250 (300) SIZE RIPPLE 315 (365) SIZE RIPPLE 350 (400) SIZE RIPPLE 400 (450) SIZE RIPPLE 56 68 82 22 x 25 100 22 x 30 120 150 180 220 270 330 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 22 x 25 22 x 30 0.75 0.85 0.55 0.65 22 x 25 0.60 450 (500) SIZE RIPPLE 22 x 25 0.55 22 x 25 0.55 22 x 30 0.65 22 x 30 0.65 22 x 35 0.80 25 x 25 0.65 25 x 25 0.75 22 x 30 0.70 22 x 35 0.79 22 x 40 0.89 25 x 25 0.70 25 x 25 0.75 25 x 30 0.85 30 x 25 0.85 22 x 30 0.75 22 x 35 0.80 22 x 40 0.89 22 x 45 0.95 25 x 25 0.75 25 x 30 0.80 25 x 30 0.85 25 x 35 0.92 30 x 25 0.87 30 x 25 0.90 22 x 35 0.80 22 x 40 0.86 22 x 40 0.85 22 x 50 1.14 25 x 30 0.80 25 x 35 0.87 22 x 45 0.93 25 x 40 1.11 30 x 25 0.85 25 x 35 0.90 30 x 30 1.10 30 x 30 0.94 35 x 25 0.96 22 x 40 1.01 22 x 45 1.05 22 x 50 1.14 25 x 45 1.25 25 x 35 1.02 25 x 40 1.07 25 x 40 1.11 30 x 35 1.24 30 x 25 1.00 30 x 30 1.05 30 x 30 1.10 35 x 25 1.20 35 x 25 1.12 22 x 30 1.00 22 x 45 1.10 22 x 50 1.16 25 x 45 1.20 25 x 50 1.36 25 x 25 1.00 25 x 40 1.12 25 x 45 1.20 30 x 35 1.20 30 x 40 1.38 30 x 30 1.10 30 x 35 1.18 35 x 30 1.24 35 x 30 1.35 35 x 25 1.15 22 x 35 1.22 25 x 45 1.25 25 x 50 1.31 25 x 50 1.36 30 x 45 1.51 25 x 25 1.15 30 x 35 1.25 30 x 40 1.33 30 x 40 1.38 35 x 35 1.50 35 x 30 1.30 35 x 30 1.35 22 x 40 1.36 25 x 50 1.53 30 x 45 1.46 30 x 45 1.51 30 x 45 1.50 25 x 30 1.30 30 x 40 1.53 35 x 35 1.45 35 x 35 1.50 30 x 50 1.70 35 x 30 1.50 35 x 40 1.70 Note: 1. Ripple Current: (A/rms) 105°C, 120Hz 101 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (µF) 390 470 560 680 820 1000 1200 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 250 (300) SIZE RIPPLE 315 (365) SIZE RIPPLE 350 (400) SIZE RIPPLE 400 (450) SIZE RIPPLE 450 (500) SIZE RIPPLE 22 x 45 1.54 30 x 45 1.71 30 x 50 1.65 30 x 50 1.70 35 x 45 1.90 25 x 35 1.48 35 x 30 1.60 35 x 40 1.65 35 x 40 1.70 30 x 25 1.45 35 x 25 1.59 22 x 50 1.78 30 x 50 1.85 35 x 45 1.85 35 x 40 1.70 35 x 50 2.10 25 x 40 1.75 35 x 35 1.75 35 x 45 1.90 30 x 30 1.72 35 x 30 1.88 25 x 40 1.80 35 x 40 2.00 35 x 50 2.10 35 x 50 1.90 30 x 35 1.89 35 x 30 1.94 25 x 50 2.10 35 x 45 2.20 35 x 50 2.30 35 x 50 2.10 30 x 40 2.10 35 x 35 2.18 30 x 45 2.30 35 x 40 2.39 30 x 50 2.55 35 x 40 2.40 35 x 45 2.65 35 x 50 2.90 Note: 1. Ripple Current: (A/rms) 105°C, 120Hz Yageo corporation ELECTROLYTIC CAPACITORS Surface Mount Aluminum Electrolytic CA [ For General ] ELECTRICAL CHARACTERISTICS Operation Temperature Range -40 to +85°C Rated Voltage Range 4 to 50VDC Rated Capacitance Range 0.1 ~ 1000μF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current (Max. 20°C) I ≤ 0.01CV (μA) or 3μA Whichever is greater (After 2 Minutes Application of DC Rated Voltage at 20°C) feature I = Leakage Current (μA), C = Rated Capacitance (μF), V = Rated Voltage (V) For General Purposes Series with 85°C 2000 Hours Low Temperature Stability Suitable for AV (TV, Video, Audio) Monitor / Computer, Home appliance, OA / HA / Communication marking Impedance Ratio at 120Hz (Max.) W V (V) 4 6.3 10 16 25 35 50 Z (-25°C) 7 4 3 2 2 2 2 Z (-40°C) 15 8 6 4 4 3 3 After applying rated voltage for 2000 hours at 85°C, the capacitors shall Endurance meet the following requirements. 1 0 (a) Capacitance Change: Within ±20% of the Initial Value (b) Dissipation Factor: Not more than 200% of Specified Value (c) Leakage Current: Not more than the Specified Value Capacitance (F) 16G Rated Voltage (VDC) 793 Date Code Shelf Life After placed at 85°C without voltage applied for 1000 hours, the capacitor shall meet the same requirement as Endurance. dimensions Unit: mm SIZE CODE Dø L A H I W P K B 4.0 5.4 4.3 5.5 Max. 1.8 0.65 ± 0.1 1.0±0.2 0.35 --- 0.20 C 5.0 5.4 5.3 6.5 Max. 2.2 0.65 ± 0.1 1.5±0.2 0.35 --- 0.20 D 6.3 5.4 6.6 7.8 Max. 2.6 0.65 ± 0.1 1.8±0.2 0.35 --- 0.20 E 8.0 6.5 8.3 9.5 Max. 3.4 0.65 ± 0.1 2.2±0.2 0.35 --- 0.20 F 8.0 10.5 8.3 10.0 Max. 3.4 0.90 ± 0.2 3.1±0.2 0.70 ± 0.20 G 10.0 10.5 10.3 12.0 Max. 3.5 0.90 ± 0.2 4.6±0.2 0.70 ± 0.20 H 6.3 7.7 6.6 7.8 Max. 0.65 ± 0.1 1.8±0.2 0.35 --- 0.20 K 0.3Max. H (I) (P) øD ± 0.5 (I) A ± 0.2 W ( ) Reference Size L ± 0.3 D ≥ ø8 = L ± 0.5 2.6 + 0.15 + 0.15 + 0.15 + 0.15 + 0.15 103 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS D x L: mm CAP. RATED VOLTAGE W V (SURGE VOLTAGE W V) (μF) 4 (5) SIZE 6.3 (8) 10 (13) 16 (20) RIPPLE DISSIPATION SIZE RIPPLE DISSIPATION SIZE RIPPLE DISSIPATION SIZE RIPPLE DISSIPATION CURRENT FACTOR CURRENT FACTOR CURRENT FACTOR CURRENT FACTOR 4.7 10 22 33 47 100 220 330 470 1000 1500 4 x 5.4 4 x 5.4 4 x 5.4 5 x 5.4 19 26 34 61 6.3 x 5.4 82 0.35 0.35 0.35 0.35 0.35 4 x 5.4 5 x 5.4 20 22 0.26 0.26 4 x 5.4 20 0.16 4 x 5.4 14 0.30 4 x 5.4 28 0.16 4 x 5.4 28 0.30 4 x 5.4 27 0.26 5 x 5.4 39 0.16 4 x 5.4 29 0.30 5 x 5.4 45 0.26 5 x 5.4 43 0.30 6.3 x 5.4 66 0.16 4 x 5.4 38 0.26 5 x 5.4 43 0.30 6.3 x 5.4 70 0.16 5 x 5.4 46 0.26 6.3 x 5.4 46 0.30 6.3 x 7.7 75 0.18 6.3 x 5.4 71 0.26 5 x 5.4 60 0.30 6.3 x 5.4 70 0.20 6.3 x 5.4 70 0.26 6.3 x 7.7 85 0.20 8 x 6.5 0.20 86 6.3 x 5.4 190 0.26 6.3 x 7.7 105 0.26 6.3 x 7.7 105 0.20 6.3 x 7.7 235 0.35 8 x 6.5 250 0.26 8 x 10.5 280 0.20 8 x 6.5 250 0.35 6.3 x 7.7 280 0.35 8 x 10.5 330 0.26 8 x 10.5 316 0.20 8 x 6.5 300 0.35 10 x 10.5 380 0.20 8 x 10.5 340 0.35 8 x 10.5 380 0.35 8 x 10.5 580 0.35 10 x 10.5 700 0.35 10 x 10.5 1000 0.35 Note: 1. Ripple Current: (mA/rms) 85°C, 120Hz 2. Dissipation Factor: 20°C, 120Hz 8 x 10.5 330 0.26 8 x 10.5 350 0.20 10 x 10.5 400 0.26 10 x 10.5 420 0.20 10 x 10.5 580 0.26 104 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 25 (32) SIZE RIPPLE CURRENT 35 (44) DISSIPATION SIZE FACTOR RIPPLE CURRENT 50 (63) DISSIPATION SIZE FACTOR RIPPLE CURRENT DISSIPATION FACTOR 0.1 4 x 5.4 1 0.12 0.22 4 x 5.4 2 0.12 0.33 4 x 5.4 3 0.12 0.47 4 x 5.4 5 0.12 1 4 x 5.4 10 0.12 2.2 4 x 5.4 8 0.12 4 x 5.4 16 0.12 3.3 4 x 5.4 10 0.12 4 x 5.4 16 0.12 4.7 4 x 5.4 22 0.14 4 x 5.4 22 0.12 5 x 5.4 23 0.12 10 4 x 5.4 24 0.20 4 x 5.4 24 0.16 5 x 5.4 28 0.12 5 x 5.4 28 0.14 5 x 5.4 30 0.12 6.3 x 5.4 35 0.12 5 x 5.4 45 0.14 5 x 5.4 49 0.23 6.3 x 5.4 70 0.12 6.3 x 5.4 55 0.14 6.3 x 5.4 60 0.12 6.3 x 7.7 90 0.12 8 x 6.5 110 0.12 22 33 47 100 220 330 470 5 x 5.4 53 0.14 6.3 x 5.4 100 0.14 6.3 x 7.7 90 0.12 6.3 x 5.4 65 0.14 8 x 6.5 130 0.14 8 x 10.5 120 0.12 6.3 x 5.4 70 0.20 6.3 x 7.7 150 0.14 6.3 x 7.7 63 0.12 8 x 6.5 96 0.16 8 x 6.5 165 0.14 8 x 10.5 100 0.12 10 x 10.5 130 0.12 6.3 x 7.7 115 0.16 6.3 x 7.7 140 0.14 8 x 10.5 160 0.12 8 x 6.5 140 0.16 8 x 6.5 170 0.14 10 x 10.5 190 0.12 8 x 10.5 180 0.16 10 x 10.5 210 0.14 8 x 6.5 210 0.16 8 x 10.5 250 0.14 10 x 10.5 310 0.12 8 x 10.5 260 0.16 10 x 10.5 310 0.14 10 x 10.5 310 0.16 8 x 10.5 350 0.16 10 x 10.5 400 0.14 10 x 10.5 430 0.16 10 x 10.5 480 0.16 Note: 1. Ripple Current: (mA/rms) 85°C, 120Hz 2. Dissipation Factor: 20°C, 120Hz Yageo corporation ELECTROLYTIC CAPACITORS CB [ For General ] Surface Mount Aluminum Electrolytic ELECTRICAL CHARACTERISTICS Operation Temperature Range -40 to +105°C Rated Voltage Range 4 to 50VDC Rated Capacitance Range 0.1 ~ 1000µF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current (Max. 20°C) I ≤ 0.01CV (µA) or 3µA Whichever is greater after 2 minutes application of DC rated working voltage at 20°C. I = Leakage Current (μA), C = Rated Capacitance (μF), V = Rated Voltage (V) Low Temperature Stability Endurance Impedance Ratio at 120Hz W V (V) 4 6.3 10 16 25 35 50 Z (-25°C) / Z (+20°C) 7 4 3 2 2 2 2 Z (-40°C) / Z (+20°C) 15 8 6 4 4 3 3 feature For General Purposes Series with 105°C 1000 Hours Suitable for AV (TV, Video, Audio) Monitor / Computer, OA / HA / Communication marking After 1000 hours application of WV at 105°C, the capacitor shall meet following requirements. (a) Capacitance Change: Within ±20% of the Initial Value Shelf Life (b) Dissipation Factor: Not more than 200% of Specified Value 1 0 (c) Leakage Current: Not more than the Specified Value 16G Rated Voltage (VDC) After placed at 105°C without voltage applied for 1000 hours, the capacitor 793 Date Code Capacitance (F) shall meet the same requirement as Endurance. dimensions Dø L A H I W P K 4.3 5.5 Max. 1.8 0.65 ± 0.1 1.0 ± 0.2 0.35 C 5.0 5.4 5.3 6.5 Max. 2.2 0.65 ± 0.1 1.5 ± 0.2 0.35 --- 0.20 D 6.3 5.4 6.6 7.8 Max. 2.6 0.65 ± 0.1 1.8 ± 0.2 0.35 --- 0.20 E 8.0 6.5 8.3 9.5 Max. 3.4 0.65 ± 0.1 2.2 ± 0.2 0.35 --- 0.20 F 8.0 10.5 8.3 10.0 Max. 3.4 0.90 ± 0.2 3.1 ± 0.2 0.70 ± 0.20 G 10.0 10.5 10.3 12.0 Max. 3.5 0.90 ± 0.2 4.6 ± 0.2 0.70 ± 0.20 H 6.3 7.7 6.6 7.8 Max. 0.65 ± 0.1 1.8 ± 0.2 0.35 --- 0.20 2.6 (P) + 0.15 + 0.15 + 0.15 + 0.15 H 5.4 øD ± 0.5 4.0 A ± 0.2 (I) B K 0.3Max. + 0.15 --- 0.20 (I) SIZE CODE Unit: mm W ( ) Reference Size L ± 0.3 D ≥ ø8 = L ± 0.5 106 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS D x L: mm CAP. RATED VOLTAGE W V (SURGE VOLTAGE W V) (μF) 4 (5) SIZE 6.3 (8) 10 (13) 16 (20) RIPPLE DISSIPATION SIZE RIPPLE DISSIPATION SIZE RIPPLE DISSIPATION SIZE RIPPLE DISSIPATION CURRENT FACTOR CURRENT FACTOR CURRENT FACTOR CURRENT FACTOR 4.7 10 4 x 5.4 20 0.16 4 x 5.4 24 0.30 4 x 5.4 28 0.16 22 4 x 5.4 20 0.35 4 x 5.4 29 0.30 4 x 5.4 36 0.30 5 x 5.4 39 0.16 33 4 x 5.4 26 0.35 4 x 5.4 43 0.30 4 x 5.4 45 0.30 6.3 x 5.4 65 0.20 47 4 x 5.4 34 0.35 5 x 5.4 46 0.30 5 x 5.4 55 0.30 6.3 x 5.4 70 0.20 6.3 x 5.4 70 0.30 6.3 x 7.7 125 0.20 8 x 6.5 0.30 6.3 x 5.4 100 0.20 6.3 x 7.7 98 0.20 8 x 6.5 130 0.20 100 220 330 470 1000 5 x 5.4 61 6.3 x 5.4 82 0.35 0.35 5 x 5.4 58 0.35 6.3 x 5.4 71 0.35 110 6.3 x 5.4 95 0.35 6.3 x 7.7 115 0.30 6.3 x 7.7 100 0.20 6.3 x 7.7 120 0.35 8 x 10.5 160 0.26 10 x 10.5 210 0.20 8 x 6.5 130 0.35 6.3 x 7.7 175 0.35 10 x 10.5 230 0.26 10 x 10.5 230 0.20 8 x 10.5 230 0.35 10 x 10.5 260 0.35 10 x 10.5 270 0.26 8 x 10.5 230 0.20 10 x 10.5 275 0.20 10 x 10.5 380 Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz 2. Dissipation Factor: 20°C, 120Hz 0.35 10 x 10.5 390 0.26 107 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 25 (32) SIZE RIPPLE CURRENT 35 (44) DISSIPATION SIZE FACTOR RIPPLE CURRENT 50 (63) DISSIPATION SIZE FACTOR RIPPLE CURRENT DISSIPATION FACTOR 0.1 4 x 5.4 1 0.12 0.22 4 x 5.4 2 0.12 0.33 4 x 5.4 3 0.12 0.47 4 x 5.4 5 0.12 1 4 x 5.4 10 0.12 2.2 4 x 5.4 15 0.12 4 x 5.4 16 0.12 3.3 4 x 5.4 18 0.12 4 x 5.4 16 0.12 4.7 4 x 5.4 22 0.14 4 x 5.4 22 0.12 5 x 5.4 23 0.12 10 4 x 5.4 23 0.14 5 x 5.4 30 0.12 6.3 x 5.4 35 0.12 5 x 5.4 28 0.14 5 x 5.4 45 0.14 6.3 x 5.4 60 0.14 6.3 x 7.7 65 0.12 6.3 x 5.4 55 0.14 8 x 6.5 70 0.12 6.3 x 5.4 65 0.16 6.3 x 7.7 70 0.12 8 x 10.5 91 0.12 22 33 47 100 220 84 0.14 6.3 x 5.4 65 0.16 6.3 x 7.7 72 0.14 6.3 x 7.7 65 0.12 8 x 6.5 91 0.16 8 x 6.5 76 0.14 10 x 10.5 100 0.12 8 x 10.5 98 0.14 6.3 x 7.7 95 0.16 6.3 x 7.7 105 0.14 8 x 10.5 120 0.12 8 x 6.5 100 0.16 8 x 10.5 130 0.14 10 x 10.5 145 0.12 8 x 10.5 130 0.16 10 x 10.5 160 0.14 8 x 10.5 220 0.16 10 x 10.5 240 0.14 10 x 10.5 273 0.16 10 x 10.5 570 0.16 330 470 8 x 6.5 Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz 2. Dissipation Factor: 20°C, 120Hz Yageo corporation ELECTROLYTIC CAPACITORS Surface Mount Aluminum Electrolytic CE [ For Long Life ] ELECTRICAL CHARACTERISTICS Operation Temperature Range -40 to +105°C Rated Voltage Range 6.3 to 50VDC Rated Capacitance Range 0.1 ~ 1000µF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current (Max. 20°C) I ≤ 0.01CV (μA) or 3μA Whichever is greater. (After Rated Voltage Applied for 2 Minutes) feature I = Leakage Current (μA), C = Rated Capacitance (μF), V = Rated Voltage (V) For Long Life Series with 105°C 2000 Hours Low Temperature Stability Suitable for AV (TV, Video, Audio), Monitor / Computer, OA / HA / Communication marking Impedance Ratio at 120Hz W V (V) Endurance 10 16 25 35 50 Z (-25°C) / Z (+20°C) 4 6.3 3 2 2 2 2 Z (-40°C) / Z (+20°C) 8 6 4 4 3 3 After 2000 hours application of WV at 105°C, the capacitors shall meet following requirements. (a) Capacitance Change: Within ±25% of the Initial Value for 4ø to 6.3ø Within ±20% of the Initial Value for 8ø to 10ø 1 0 Capacitance (F) (b) Dissipation Factor: Not more than 200% of Specified Value 16D Rated Voltage (VDC) (c) Leakage Current: Not more than the Specified Value Date Code 793 Shelf Life After placed at 105°C without voltage applied for 1000 hours, the capacitor shall meet the same requirement as Endurance. dimensions Unit: mm SIZE CODE Dø L A H I W P K B 4.0 5.4 4.3 5.5 Max. 1.8 0.65 ± 0.1 1.0 ± 0.2 0.35 --- 0.20 C 5.0 5.4 5.3 6.5 Max. 2.2 0.65 ± 0.1 1.5 ± 0.2 0.35 --- 0.20 D 6.3 5.4 6.6 7.8 Max. 2.6 0.65 ± 0.1 1.8 ± 0.2 0.35 --- 0.20 E 8.0 6.5 8.3 9.5 Max. 3.4 0.65 ± 0.1 2.2 ± 0.2 0.35 --- 0.20 F 8.0 10.5 8.3 10.0 Max. 3.4 0.90 ± 0.2 3.1 ± 0.2 0.70 ± 0.20 G 10.0 10.5 10.3 12.0 Max. 3.5 0.90 ± 0.2 4.6 ± 0.2 0.70 ± 0.20 H 6.3 7.7 6.6 7.8 Max. 0.65 ± 0.1 1.8 ± 0.2 0.35 --- 0.20 K 0.3Max. H (I) (P) øD ± 0.5 (I) A ± 0.2 W ( ) Reference Size L ± 0.3 D ≥ ø8 = L ± 0.5 2.6 + 0.15 + 0.15 + 0.15 + 0.15 + 0.15 109 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 6.3 (8) SIZE RIPPLE CURRENT 10 (13) DISSIPATION SIZE FACTOR RIPPLE CURRENT 16 (20) DISSIPATION SIZE FACTOR RIPPLE CURRENT DISSIPATION FACTOR 4.7 4 x 5.4 20 0.16 10 4 x 5.4 28 0.16 22 5 x 5.4 29 0.30 5 x 5.4 36 0.22 5 x 5.4 39 0.16 33 5 x 5.4 43 0.30 5 x 5.4 45 0.22 6.3 x 5.4 65 0.16 47 5 x 5.4 44 0.30 6.3 x 5.4 70 0.22 6.3 x 5.4 70 0.16 6.3 x 5.4 46 0.30 6.3 x 7.7 80 0.16 6.3 x 5.4 71 0.30 100 220 330 470 1000 6.3 x 5.4 85 0.22 6.3 x 5.4 100 0.20 6.3 x 7.7 104 0.22 6.3 x 7.7 130 0.20 8 x 6.5 110 0.22 8 x 10.5 140 0.20 10 x 10.5 210 0.20 10 x 10.5 230 0.20 10 x 10.5 275 0.20 6.3 x 7.7 115 0.35 6.3 x 7.7 105 0.26 8 x 10.5 150 0.35 8 x 10.5 160 0.26 8 x 10.5 230 0.35 8 x 10.5 190 0.30 10 x 10.5 230 0.26 10 x 10.5 270 0.26 10 x 10.5 390 0.26 8 x 10.5 260 0.35 10 x 10.5 260 0.35 10 x 10.5 380 0.35 Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz 2. Dissipation Factor: 20°C, 120Hz 110 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 25 (32) SIZE RIPPLE CURRENT 35 (44) DISSIPATION SIZE FACTOR RIPPLE CURRENT 50 (63) DISSIPATION SIZE FACTOR RIPPLE CURRENT DISSIPATION FACTOR 0.1 4 x 5.4 1 0.12 0.22 4 x 5.4 2 0.12 0.33 4 x 5.4 3 0.12 0.47 4 x 5.4 5 0.12 1 4 x 5.4 10 0.12 2.2 4 x 5.4 16 0.12 3.3 4 x 5.4 16 0.12 4 x 5.4 18 0.12 5 x 5.4 23 0.12 4.7 4 x 5.4 22 0.14 5 x 5.4 23 0.12 6.8 4 x 5.4 25 0.14 5 x 5.4 27 0.12 5 x 5.4 30 0.12 10 5 x 5.4 28 0.14 5 x 5.4 30 0.12 5 x 5.4 35 0.12 22 6.3 x 5.4 55 0.14 6.3 x 5.4 60 0.14 8 x 10.5 70 0.12 33 6.3 x 5.4 65 0.16 6.3 x 7.7 79 0.14 8 x 10.5 91 0.12 8 x 6.5 84 0.14 8 x 10.5 98 0.14 10 x 10.5 100 0.12 10 x 10.5 160 0.14 10 x 10.5 145 0.12 10 x 10.5 240 0.14 10 x 10.5 200 0.12 47 6.3 x 5.4 70 0.16 6.3 x 7.7 86 0.16 8 x 6.5 91 0.16 6.3 x 7.7 90 0.16 8 x 10.5 130 0.16 8 x 10.5 220 0.16 10 x 10.5 273 0.16 330 10 x 10.5 334 0.16 470 10 x 10.5 300 0.16 100 220 Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz 2. Dissipation Factor: 20°C, 120Hz Yageo corporation ELECTROLYTIC CAPACITORS CZ [ For Low Impedance ] Surface Mount Aluminum Electrolytic ELECTRICAL CHARACTERISTICS Operation Temperature Range -40 to +105°C Rated Voltage Range 4 to 50VDC Rated Capacitance Range 0.1 ~ 1000µF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current (Max.20°C) I ≤ 0.01CV (μA) or 3μA (After 2 Minutes Application of DC Rated Voltage at 20°C) I = Leakage Current (μA), C = Rated Capacitance (μF), V = Rated Voltage (V) Low Temperature Stability Endurance For Low ESR Series with 105°C 1000 Hours Impedance Ratio at 120Hz W V (V) feature 4 6.3 10 16 25 35 50 Z (-25°C) / Z (+20°C) 4 2 2 2 2 2 2 Z (-40°C) / Z (+20°C) 8 4 4 3 3 3 3 After 1000 hours application of WV at 105°C, the capacitor shall meet Suitable for AV (TV, Video, Audio), Monitor / Computer, Battery Charger, DC / DC Converter, SMPS, Noise Filter marking following requirements. (a) Capacitance Change: Within ±20% of the Initial Value (b) Dissipation Factor: Not more than 200% of Specified Value 1 0 (c) Leakage Current: Not more than the Specified Value Shelf Life Capacitance (F) 16Z After placed at 105°C without voltage applied for 1000 hours, the capacitor Rated Voltage (VDC) Date Code 793 shall meet the same requirement as Endurance. dimensions Dø L A H I W P K 4.3 5.5 Max. 1.8 0.65 ± 0.1 1.0± 0.2 0.35 C 5.0 5.4 5.3 6.5 Max. 2.2 0.65 ± 0.1 1.5± 0.2 0.35 --- 0.20 D 6.3 5.4 6.6 7.8 Max. 2.6 0.65 ± 0.1 1.8± 0.2 0.35 --- 0.20 E 8.0 6.5 8.3 9.5 Max. 3.4 0.65 ± 0.1 2.2± 0.2 0.35 --- 0.20 F 8.0 10.5 8.3 10.0 Max. 3.4 0.90 ± 0.2 3.1± 0.2 0.70 ± 0.20 G 10.0 10.5 10.3 12.0 Max. 3.5 0.90 ± 0.2 4.6± 0.2 0.70 ± 0.20 H 6.3 7.7 6.6 7.8 Max. 0.65 ± 0.1 1.8± 0.2 0.35 --- 0.20 2.6 (P) + 0.15 + 0.15 + 0.15 + 0.15 H 5.4 øD ± 0.5 4.0 A ± 0.2 (I) B K 0.3Max. + 0.15 --- 0.20 (I) SIZE CODE Unit: mm W ( ) Reference Size L ± 0.3 D ≥ ø8 = L ± 0.5 112 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 4 (5) SIZE RIPPLE CURRENT DISSIPATION ESR FACTOR 6.3 (8) SIZE RIPPLE CURRENT DISSIPATION ESR FACTOR 4.7 4 x 5.4 60 0.35 4.00 6.8 4 x 5.4 60 0.35 4.00 10 4 x 5.4 60 0.35 4.00 22 4 x 5.4 60 0.35 4.00 4 x 5.4 60 0.26 4.00 33 4 x 5.4 60 0.35 4.00 5 x 5.4 95 0.26 2.60 47 4 x 5.4 60 0.35 4.00 5 x 5.4 95 0.26 2.60 68 4 x 5.4 60 0.35 4.00 6.3 x 5.4 140 0.26 1.30 100 5 x 5.4 95 0.35 3.00 6.3 x 5.4 140 0.26 1.30 150 6.3 x 5.4 140 0.35 2.60 8 x 6.5 230 0.35 0.80 220 6.3 x 5.4 140 0.35 2.60 8 x 6.5 230 0.35 0.80 330 8 x 10.5 450 0.35 0.50 470 10 x 10.5 670 0.35 0.30 1000 10 x 10.5 670 0.35 0.30 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. Dissipation Factor: 20°C, 120Hz 3. ESR: 20°C, 100KHz (Ω) 113 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 10 (13) SIZE RIPPLE CURRENT DISSIPATION ESR FACTOR 16 (20) SIZE RIPPLE CURRENT DISSIPATION ESR FACTOR 4.7 4 x 5.4 60 0.16 4.00 6.8 4 x 5.4 60 0.16 4.00 10 4 x 5.4 60 0.22 4.00 4 x 5.4 60 0.16 4.00 22 5 x 5.4 95 0.22 2.60 5 x 5.4 95 0.16 2.60 33 5 x 5.4 95 0.22 2.60 5 x 5.4 95 0.16 2.60 47 6.3 x 5.4 95 0.22 1.30 6.3 x 5.4 140 0.16 1.30 68 6.3 x 5.4 140 0.22 1.30 8 x 6.5 230 0.20 0.80 100 6.3 x 5.4 140 0.22 1.30 8 x 6.5 230 0.20 0.80 150 8 x 6.5 230 0.26 0.80 10 x 10.5 450 0.20 0.50 220 8 x 6.5 230 0.26 0.80 10 x 10.5 450 0.20 0.50 330 8 x 10.5 450 0.26 0.50 10 x 10.5 670 0.20 0.30 470 10 x 10.5 670 0.26 0.30 10 x 10.5 670 0.20 0.30 1000 10 x 10.5 670 0.26 0.30 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. Dissipation Factor: 20°C, 120Hz 3. ESR: 20°C, 100KHz (Ω) 114 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. RATED VOLTAGE W V (SURGE VOLTAGE W V) (μF) 25 (32) SIZE RIPPLE DISSIPATION ESR CURRENT FACTOR 35 (44) SIZE RIPPLE DISSIPATION ESR CURRENT FACTOR D x L: mm 50 (63) SIZE RIPPLE DISSIPATION ESR CURRENT FACTOR 0.1 4 x 5.4 60 0.12 5.00 0.22 4 x 5.4 60 0.12 5.00 0.33 4 x 5.4 60 0.12 5.00 0.47 4 x 5.4 60 0.12 5.00 1 4 x 5.4 60 0.12 4.00 4 x 5.4 60 0.12 5.00 2.2 4 x 5.4 60 0.12 4.00 4 x 5.4 60 0.12 5.00 3.3 4 x 5.4 60 0.12 4.00 4 x 5.4 60 0.12 5.00 95 0.12 4.00 4.7 4 x 5.4 60 0.14 4.00 4 x 5.4 60 0.12 4.00 5 x 5.4 6.8 4 x 5.4 60 0.14 4.00 5 x 5.4 95 0.12 2.60 6.3 x 5.4 140 0.12 2.60 10 5 x 5.4 95 0.14 2.60 5 x 5.4 95 0.12 2.60 6.3 x 5.4 140 0.12 2.60 22 6.3 x 5.4 140 0.14 1.30 6.3 x 5.4 140 0.12 1.30 8 x 6.5 230 0.12 1.30 33 6.3 x 5.4 140 0.14 1.30 8 x 6.5 230 0.14 0.80 8 x 10.5 300 0.12 1.10 47 6.3 x 5.4 140 0.14 1.30 8 x 6.5 230 0.14 0.80 10 x 10.5 670 0.12 0.80 68 8 x 10.5 450 0.16 0.50 8 x 10.5 450 0.14 0.50 10 x 10.5 670 0.12 0.80 100 8 x 10.5 450 0.16 0.50 10 x 10.5 670 0.14 0.30 10 x 10.5 670 0.12 0.80 150 10 x 10.5 670 0.16 0.30 10 x 10.5 670 0.14 0.30 220 10 x 10.5 670 0.16 0.30 10 x 10.5 670 0.14 0.30 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. Dissipation Factor: 20°C, 120Hz 3. ESR: 20°C, 100KHz (Ω) Yageo corporation ELECTROLYTIC CAPACITORS CD [ For Ultra Low Impedance ] Surface Mount Aluminum Electrolytic ELECTRICAL CHARACTERISTICS Operation Temperature Range -40 to +105°C Rated Voltage Range 6.3 to 35VDC Rated Capacitance Range 4.7 ~ 1500µF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current (Max. 20°C) I ≤ 0.01CV (µA) or 3µA (After 2 Minutes Application of DC Rated Voltage at 20°C) I = Leakage Current (μA), C = Rated Capacitance (μF), V = Rated Voltage (V) feature Dissipation Factor (tanδ) W V(V) 6.3 10 16 25 35 For Ultra Low Impedance Series with 105°C 2000 Hours (120Hz, 20°C) tan δ 0.26 0.19 0.16 0.14 0.12 Low Temperature Stability Impedance Ratio at 120Hz Suitable for AV (TV, Video, Audio), Monitor / Computer, OA / HA / Communication, SMPS W V (V) Endurance 6.3 10 16 25 35 Z (-25°C) / Z (+20°C) 2 2 2 2 2 Z (-40°C) / Z (+20°C) 3 3 3 3 3 marking After 2,000 hours application of WV at 105°C, the capacitor shall meet following requirements. 1 0 (a) Capacitance Change: Within ±30% of the Initial Value (b) Dissipation Factor: Not more than 200% of Specified Value Rated Voltage (VDC) Date Code 793 (c) Leakage Current: Not more than the Specified Value Shelf Life Capacitance (F) 16E After placed at 105°C without voltage applied for 1000 hours, the capacitor shall meet the same requirement as Endurance. dimensions Dø L A H I W P K 4.3 5.5 Max. 1.8 0.65 ± 0.1 1.0 ± 0.2 0.35 C 5.0 5.4 5.3 6.5 Max. 2.2 0.65 ± 0.1 1.5 ± 0.2 0.35 --- 0.20 D 6.3 5.4 6.6 7.8 Max. 2.6 0.65 ± 0.1 1.8 ± 0.2 0.35 --- 0.20 E 8.0 6.2 8.3 9.5 Max. 3.4 0.65 ± 0.1 2.2 ± 0.2 0.35 --- 0.20 F 8.0 10.2 8.3 10.0 Max. 3.4 0.90 ± 0.2 3.1 ± 0.2 0.70 ± 0.20 G 10.0 10.2 10.3 12.0 Max. 3.5 0.90 ± 0.2 4.6 ± 0.2 0.70 ± 0.20 H 6.3 7.7 6.6 7.8 Max. 0.65 ± 0.1 1.8 ± 0.2 2.6 (P) + 0.15 + 0.15 + 0.15 + 0.15 0.35--- 0.20 H 5.4 øD ± 0.5 4.0 A ± 0.2 (I) B K 0.3Max. + 0.15 --- 0.20 (I) SIZE CODE Unit: mm W ( ) Reference Size L ± 0.3 D ≥ ø8 = L ± 0.5 116 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) 22 33 47 6.3 (8) SIZE RIPPLE ESR 10 (13) SIZE RIPPLE ESR 16 (20) SIZE RIPPLE ESR 4 x 5.4 90 1.93 4 x 5.4 90 1.93 4 x 5.4 90 1.93 5 x 5.4 160 1.00 5 x 5.4 160 1.00 5 x 5.4 160 1.00 6.3 x 5.4 240 0.52 4 x 5.4 90 1.93 4 x 5.4 90 1.93 5 x 5.4 160 1.00 5 x 5.4 160 1.00 6.3 x 5.4 240 0.52 150 8 x 6.5 240 220 8 x 6.5 240 100 330 470 680 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 5 x 5.4 160 1.00 6.3 x 5.4 190 0.52 0.52 6.3 x 5.4 240 0.52 0.30 6.3 x 7.7 240 0.34 6.3 x 7.7 280 0.34 0.30 6.3 x 7.7 280 0.34 6.3 x 7.7 330 0.34 8 x 6.5 300 0.26 8 x 10.5 370 0.22 8 x 10.5 600 0.16 8 x 10.5 600 0.16 8 x 10.5 600 0.16 8 x 10.5 600 0.16 10 x 10.5 600 0.08 10 x 10.5 850 0.08 10 x 10.5 850 0.08 0.34 8 x 6.5 300 0.26 8 x 10.5 600 0.16 0.16 820 1000 10 x 10.5 600 0.16 1200 10 x 10.5 700 0.16 1500 10 x 10.5 850 0.08 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. ESR: 100KHz / 20°C (mΩ) 1.93 190 280 600 90 6.3 x 5.4 6.3 x 7.7 8 x 10.5 4 x 5.4 10 x 10.5 600 0.12 117 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) 25 (32) SIZE RIPPLE ESR 4.7 10 D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 4 x 5.4 90 1.93 35 (44) SIZE RIPPLE ESR 4 x 5.4 90 1.93 4 x 5.4 90 1.93 5 x 5.4 160 1.00 22 5 x 5.4 160 1.00 5 x 5.4 160 1.00 33 5 x 5.4 160 1.00 6.3 x 5.4 240 0.52 6.3 x 5.4 240 0.52 47 6.3 x 5.4 240 0.52 6.3 x 5.4 240 0.52 68 6.3 x 5.4 240 0.52 6.3 x 7.7 280 0.34 100 6.3 x 7.7 280 0.34 6.3 x 7.7 280 0.34 8 x 6.5 300 0.26 8 x 10.5 600 0.16 10 x 10.5 850 0.08 150 8 x 10.5 600 0.16 8 x 10.5 600 0.16 220 8 x 10.5 600 0.16 10 x 10.5 600 0.16 330 10 x 10.5 600 0.16 10 x 10.5 850 0.08 470 10 x 10.5 850 0.08 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. ESR: 100KHz / 20°C (Ω Max.) Yageo corporation ELECTROLYTIC CAPACITORS Conductive Polymer Solid Capacitors CP [ For Ultra Low ESR & High Ripple Current ] 105°C, 2000 Hours 8mm Height and Ultra Low ESR ELECTRICAL CHARACTERISTICS Operation Temperature Range -55 ~ +105°C Rated Voltage Range 2.5 ~ 6.3VDC Rated Capacitance Range 470 ~ 820μF Capacitance Tolerance -20 ~ +20% at 120Hz, 20°C Leakage Current (Max. 20°C) I ≤ 0.2CV (μA) ( After Rated Voltage Applied for 2 Minutes ) I = Leakage Current (μA), C = Rated Capacitance (μF), V = Rated Voltage (V) description Recommended Applications: Montherboard, DC / DC Converter, DSC, PDA, HD Drive, MO Drive, DVD Drive, Navigation system, Portable Communication Devices Dissipation Factor W V(V) 2.5 ~ 6.3V at 120Hz, 20°C D.F (%) 80 Low Temperature Stability Impedance Ratio at 20°C (Max.) Endurance W V (V) 2.5 ~ 16V(Rated Voltage) Impedance Z - 25°C / Z + 20°C ≤1.15 Z - 55°C / Z + 20°C ≤1.25 After applying rated voltage for 2000 hours at 105°C, the capacitors shall meet the follow requirements. (a) Appearance: No Significant Damage (b) Capacitance Change: Within ±20% of the Initial Value (c) Dissipation Factor: Not more than 150% of the Initial Specified Value (d) Equivalent Series Resistance: Not more than 150% of the Initial Specified Value (e) Leakage Current: Not more than the Initial Specified Value Humidity Test After subjecting 90 to 95% RH for 1000 hours at 60°C, the capacitors shall meet the requirement as Endurance. MARKING diagram of dimensions Unit: mm Rubber Stand-off 1 0 Series Identification Rated Voltage P±0.5 793 ø0.6 øD+0.5 max. 2.5CP Coated case Capacitance(µF) Date Code Polarity (negative) Indication L +a 15Min. 4Min. D±0.5 Dø PA a (Max.) P 3.5 1.0 119 case size & permissible ripple current of standard products CAP. (µF) D x L: mm Rated Voltage W V 2.5 SIZE RIPPLE ESR 4 SIZE RIPPLE ESR 470 560 8x8 4400 6 820 8x8 4400 6 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. ESR: 100KHz / 20°C (mΩ) 8x8 4400 7 6.3 SIZE RIPPLE 8x8 4400 8 8x8 4400 8 ESR Yageo corporation ELECTROLYTIC CAPACITORS Conductive Polymer Solid Capacitors CG [ For Low ESR & High Ripple Current ] 105°C, 2000 Hours and Ultra Low ESR ELECTRICAL CHARACTERISTICS Operation Temperature Range -55 ~ +105°C Rated Voltage Range 2.5 ~ 16VDC Rated Capacitance Range 270 ~ 1500μF Capacitance Tolerance -20 ~ +20% at 120Hz, 20°C Leakage Current (Max. 20°C) I ≤ 0.2CV (μA) ( After Rated Voltage Applied for 2 Minutes ) I = Leakage Current (μA), C = Rated Capacitance (μF), V = Rated Voltage (V) description Long life for 2000 hours at 105°C, ideally suited for high quality and high reliability applications. Feature High CV Product Dissipation Factor W V(V) 2.5 ~ 16V at 120Hz, 20°C D.F (%) 80 Low Temperature Stability Impedance Ratio at 20°C (Max.) Endurance W V (V) 2.5 ~ 16V Impedance Z - 25°C / Z + 20°C ≤1.15 Z - 55°C / Z + 20°C ≤1.25 (Z: 100KHz) After applying rated voltage for 2000 hours at 105°C, the capacitors shall meet the follow requirements. (a) Appearance: No Significant Damage (b) Capacitance Change: Within±20% of Initial Value (c) Dissipation Factor: Not more than 150% of the Initial Specified Value (d) Equivalent Series Resistance: Not more than 150% of the Initial Specified Value (e) Leakage Current: Not more than the Initial Specified Value Humidity Test After Subjecting 90 to 95% RH for 1000 hours at 60°C, the capacitors shall meet the requirement as Endurance. MARKING diagram of dimensions Unit: mm Rubber Stand-off 1 0 Series Identification Rated Voltage Date Code Polarity (negative) Indication P±0.5 793 ø0.6 øD+0.5 max. 2.5CG Coated case Capacitance(µF) L+a 15Min. 4Min. D+0.5max Dø P a (Max.) 8 3.5 1.0 10 5 1.0 121 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V 2.5 SIZE RIPPLE ESR 4 SIZE RIPPLE ESR 6.3 SIZE RIPPLE ESR 10 SIZE RIPPLE ESR 180 16 SIZE RIPPLE ESR 8 x 11.5 4360 16.00 270 8 x 11.5 5600 7.00 8 x 11.5 5000 11.00 330 8 x 11.5 5600 7.00 10 x 12 6100 10.00 8 x 11.5 5600 7.00 10 x 12 6100 10.00 10 x 12.5 6100 7.00 10 x 12 7.00 470 8 x 11.5 5600 680 820 8 x 11.5 5600 8 x 11.5 5600 1500 10 x 12 6100 10 x 12 6100 10 x 12 6100 7.00 7.00 1200 7.00 Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz 2. ESR: 100KHz / 20°C (mΩ) 7.00 7.00 7.00 6100 Yageo corporation ELECTROLYTIC CAPACITORS Screw Type Aluminum Electrolytic Capacitors NP [ For General ] For Large Power Source, Converter Circuit ELECTRICAL CHARACTERISTICS Operating Temperature Range -40 to +85°C -25 to +85°C Rated Voltage Range 10 ~ 250V 315 ~ 450V Capacitance Tolerance ±20% (120Hz, +20°C) Leakage Current I = 0.02CV or 5mA Whichever is smaller. (After 5 Minutes Application of DC Rated Voltage at 20°C) Description Dissipation Factor Endurance : 85°C, 2000 Hours Endurance at 120Hz, +20°C Less than the Value Specified in the Standard Products Tables After applying rated voltage for 2000 hours at +85°C and then resumed Used high ripple current, large power source, converter circuit, etc. 16 hours. MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient (c) Leakage Current: ≤ Initial Specified Value (a) Capacitance Change: ±20% Initial Measured Value (b) Dissipation Factor: ≤ 2 Times Initial Specified Value After storage for 1000 hours at +85°C, Ur to be applied for 30 minutes 50 10~50V 0.95 1.00 1.04 1.10 63~100V 0.95 1.00 1.06 1.16 (b) Dissipation Factor: ≤ 2 Times Initial Specified Value 160~200V 0.90 1.00 1.10 1.20 (c) Leakage Current: ≤ Initial Specified Value 250~450V 0.80 1.00 1.10 1.20 FREQUENCY (Hz) 3K 5K 10K 20K 10~50V 1.12 1.13 1.15 1.15 63~100V 1.20 1.25 1.30 1.36 160~200V 1.35 1.40 1.50 1.55 250~450V 1.35 1.40 1.50 1.55 and then resumed 16 hours. (a) Capacitance Change: ±20% Initial Measured Value diagram of dimensions Sleeve M5x0.8 Safety Vent F ±1 100 (120) 300 1K Shelf Life FREQUENCY (Hz) L ±2 20max Dø±1 Unit: mm Dø F 35 12.7 51 22 63.5 28.6 76 32 89 32 123 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. RATED VOLTAGE W V (SURGE VOLTAGE W V) (μF) 10 (13) SIZE 16 (20) RIPPLE DISSIPATION SIZE CURRENT FACTOR 25 (32) RIPPLE DISSIPATION SIZE CURRENT FACTOR D x L: mm 35 (44) RIPPLE DISSIPATION SIZE CURRENT FACTOR RIPPLE DISSIPATION CURRENT FACTOR 10000 35 x 50 3.40 0.40 12000 35 x 50 3.70 0.40 15000 35 x 50 3.70 0.50 35 x 65 4.20 0.40 18000 35 x 50 4.10 0.50 35 x 80 4.90 0.40 22000 35 x 50 4.10 0.60 35 x 50 4.50 0.50 35 x 80 5.70 0.40 27000 35 x 50 4.50 0.60 35 x 65 5.00 0.50 35 x 100 6.30 0.40 33000 35 x 50 4.30 0.80 35 x 50 5.00 0.60 35 x 80 5.90 0.50 35 x 100 7.20 0.40 39000 35 x 50 4.70 0.80 35 x 65 5.90 0.60 35 x 80 6.70 0.50 35 x 120 7.30 0.50 47000 35 x 65 5.20 0.80 35 x 80 6.40 0.60 35 x 100 7.70 0.50 35 x 120 8.70 0.50 56000 35 x 80 6.10 0.80 35 x 80 7.30 0.60 35 x 100 7.90 0.60 51 x 95 8.60 0.60 68000 35 x 80 6.70 0.80 35 x 100 8.40 0.60 35 x 120 9.10 0.60 51 x 95 9.80 0.60 82000 35 x 100 7.70 0.80 35 x 100 8.30 0.80 35 x 120 10.40 0.60 51 x 115 11.60 0.60 100000 35 x 100 8.80 0.80 35 x 120 9.50 0.80 51 x 95 10.30 0.80 63.5 x 95 13.30 0.60 120000 35 x 120 10.00 0.80 35 x 120 10.90 0.80 51 x 115 11.70 0.80 63.5 x 115 14.80 0.60 150000 35 x 120 10.80 1.00 51 x 95 11.30 1.00 51 x 130 14.10 0.80 63.5 x 120 14.90 0.80 180000 51 x 95 12.00 1.00 51 x 115 12.80 1.00 63.5 x 95 15.70 0.80 63.5 x 130 17.00 0.80 220000 51 x 120 11.20 1.50 51 x 130 15.30 1.00 63.5 x 115 16.10 1.00 76 x 115 20.00 0.80 270000 51 x 120 12.80 1.50 63.5 x 95 17.60 1.00 63.5 x 130 18.60 1.00 76 x 130 20.30 1.00 330000 63.5 x 95 15.30 1.50 63.5 x 115 16.80 1.50 63.5 x 155 21.90 1.00 76 x 155 23.50 1.00 390000 63.5 x 115 17.30 1.50 63.5 x 130 18.30 1.50 76 x 120 22.00 1.20 89 x 130 26.40 1.00 470000 63.5 x 130 16.70 2.00 76 x 120 21.30 1.50 76 x 155 25.60 1.20 89 x 155 29.60 1.00 560000 76 x 115 19.00 2.00 76 x 130 23.60 1.50 89 x 130 27.90 1.20 680000 76 x 130 21.70 2.00 76 x 155 27.60 1.50 89 x 155 32.50 1.20 820000 76 x 155 24.70 2.00 89 x 155 27.10 2.00 Note: 1. Ripple Current: (A/rms) 85°C, 120Hz 2. Dissipation Factor: 120Hz / 20°C 124 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. RATED VOLTAGE W V (SURGE VOLTAGE W V) (μF) 50 (63) SIZE 63 (72) RIPPLE DISSIPATION SIZE CURRENT FACTOR D x L: mm 80 (100) 100 (125) RIPPLE DISSIPATION SIZE RIPPLE DISSIPATION SIZE RIPPLE DISSIPATION CURRENT FACTOR CURRENT FACTOR CURRENT FACTOR 1800 35 x 50 1.90 0.25 2200 35 x 50 2.10 0.25 2700 35 x 50 2.30 0.25 3300 35 x 50 2.50 0.25 35 x 65 2.60 0.25 3900 35 x 50 2.70 0.25 35 x 50 2.80 0.25 35 x 80 3.00 0.25 4700 35 x 50 3.00 0.25 35 x 65 3.00 0.25 35 x 80 3.50 0.25 5600 35 x 50 3.00 0.30 35 x 50 3.30 0.25 35 x 80 3.60 0.25 35 x 100 3.90 0.25 6800 35 x 50 3.30 0.30 35 x 65 3.60 0.25 35 x 80 3.90 0.25 35 x 100 4.50 0.25 8200 35 x 50 3.60 0.30 35 x 80 4.30 0.25 35 x 80 4.50 0.25 35 x 120 5.10 0.25 10000 35 x 65 4.00 0.30 35 x 80 4.90 0.25 35 x 100 5.20 0.25 35 x 120 5.90 0.25 12000 35 x 80 4.70 0.30 35 x 100 5.60 0.25 35 x 100 5.90 0.25 51 x 75 6.40 0.25 15000 35 x 80 5.50 0.30 35 x 100 5.90 0.30 35 x 120 6.80 0.25 51 x 95 7.00 0.25 18000 35 x 100 6.20 0.30 35 x 120 6.70 0.30 35 x 120 7.80 0.25 51 x 115 8.30 0.25 22000 35 x 120 6.30 0.40 35 x 120 7.80 0.30 51 x 95 8.00 0.30 51 x 130 10.00 0.25 27000 35 x 120 7.10 0.40 51 x 95 7.40 0.40 51 x 95 9.20 0.30 63.5 x 115 11.50 0.25 33000 51 x 95 8.20 0.40 51 x 95 8.40 0.40 51 x 115 10.50 0.30 63.5 x 130 11.90 0.25 39000 51 x 95 8.10 0.50 51 x 115 9.50 0.40 51 x 130 12.00 0.30 76 x 115 13.40 0.25 47000 51 x 115 9.30 0.50 51 x 130 11.30 0.40 63.5 x 115 13.60 0.30 76 x 130 14.20 0.35 56000 63.5 x 95 10.50 0.50 63.5 x 115 12.80 0.40 63.5 x 130 13.40 0.40 76 x 155 16.00 0.35 68000 63.5 x 95 12.00 0.50 63.5 x 120 12.70 0.50 76 x 115 15.40 0.40 89 x 130 18.80 0.35 82000 63.5 x 115 13.70 0.50 63.5 x 130 14.50 0.50 76 x 130 17.50 0.40 89 x 155 20.50 0.35 100000 76 x 115 14.70 0.60 76 x 115 16.70 0.50 76 x 155 20.50 0.40 89 x 171 24.00 0.35 120000 76 x 120 16.70 0.60 76 x 130 18.90 0.50 89 x 130 22.70 0.40 150000 76 x 130 19.30 0.60 76 x 155 22.40 0.50 89 x 155 26.50 0.40 180000 76 x 155 21.90 0.60 89 x 130 22.40 0.60 220000 89 x 130 21.40 0.60 89 x 155 26.20 0.60 27000 0.60 89 x 155 24.60 Note: 1. Ripple Current: (A/rms) 85°C, 120Hz 2. Dissipation Factor: 120Hz / 20°C 125 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS D x L: mm CAP. RATED VOLTAGE W V (SURGE VOLTAGE W V) (μF) 160 (200) 200 (250) 250 (300) 350 (400) SIZE RIPPLE DISSIPATION SIZE RIPPLE DISSIPATION SIZE RIPPLE DISSIPATION SIZE RIPPLE DISSIPATION CURRENT FACTOR CURRENT FACTOR CURRENT FACTOR CURRENT FACTOR 390 35 x 50 1.67 0.20 470 35 x 80 2.15 0.20 560 35 x 80 2.37 0.20 680 35 x 80 2.59 0.20 820 35 x 100 3.07 0.20 1000 35 x 100 3.41 0.20 1200 51 x 75 3.81 0.20 1500 35 x 100 3.22 0.25 51 x 75 4.26 0.20 1800 35 x 100 3.52 0.25 51 x 95 5.14 0.20 2200 35 x 100 3.92 0.25 51 x 75 4.00 0.25 51 x 95 5.70 0.20 2700 35 x 120 4.70 0.25 51 x 75 4.44 0.25 51 x 130 7.14 0.20 3300 35 x 120 5.18 0.25 51 x 75 4.92 0.25 51 x 95 5.40 0.25 51 x 130 7.92 0.20 3900 51 x 75 5.33 0.25 51 x 75 5.33 0.25 51 x 115 6.29 0.25 63.5 x 115 9.00 0.20 4700 51 x 75 5.85 0.25 51 x 95 6.44 0.25 63.5 x 95 7.10 0.25 63.5 x 130 10.33 0.20 5600 51 x 95 7.03 0.25 51 x 115 7.55 0.25 63.5 x 95 7.77 0.25 76 x 115 11.36 0.20 6800 51 x 95 7.77 0.25 51 x 130 8.77 0.25 63.5 x 115 9.14 0.25 76 x 130 13.10 0.20 8200 51 x 115 9.14 0.25 63.5 x 95 9.40 0.25 63.5 x 115 10.03 0.25 76 x 155 15.43 0.20 10000 63.5 x 95 10.36 0.25 63.5 x 95 10.36 0.25 63.5 x 130 11.66 0.25 89 x 155 18.13 0.20 12000 63.5 x 95 11.32 0.25 76 x 95 12.06 0.25 76 x 115 12.88 0.25 89 x 155 20.02 0.20 15000 63.5 x 130 14.28 0.25 76 x 95 14.43 0.25 76 x 130 15.10 0.25 89 x 195 24.50 0.20 18000 63.5 x 130 15.61 0.25 76 x 130 16.50 0.25 76 x 155 17.69 0.25 89 x 235 28.83 0.20 22000 76 x 130 18.28 0.25 76 x 155 19.61 0.25 89 x 155 20.91 0.25 27000 76 x 130 20.24 0.25 89 x 130 21.51 0.25 30000 89 x 130 23.75 0.25 89 x 155 25.53 0.25 39000 89 x 155 27.86 0.25 Note: 1. Ripple Current: (A/rms) 85°C, 120Hz. 2. Dissipation Factor: 120Hz / 20°C 126 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 400 (450) SIZE RIPPLE CURRENT DISSIPATION FACTOR 270 450 (500) SIZE RIPPLE CURRENT DISSIPATION FACTOR 35 x 50 1.37 0.20 330 35 x 50 1.52 0.20 35 x 80 1.82 0.20 390 35 x 80 1.96 0.20 35 x 80 1.96 0.20 470 35 x 80 2.15 0.20 35 x 80 2.15 0.20 560 35 x 80 2.37 0.20 35 x 100 2.55 0.20 680 35 x 100 1.82 0.20 35 x 100 2.81 0.20 820 35 x 100 3.07 0.20 51 x 75 3.18 0.20 1000 51 x 75 3.48 0.20 51 x 75 3.48 0.20 1200 51 x 75 3.82 0.20 51 x 95 4.22 0.20 1500 51 x 95 4.70 0.20 51 x 115 5.07 0.20 1800 51 x 95 5.15 0.20 51 x 130 5.85 0.20 2200 51 x 130 6.44 0.20 63.5 x 95 6.29 0.20 2700 51 x 130 6.96 0.20 63.5 x 115 7.48 0.20 3300 63.5 x 95 8.22 0.20 63.5 x 130 8.66 0.20 3900 63.5 x 115 9.40 0.20 76 x 115 9.47 0.20 4700 63.5 x 130 10.44 0.20 76 x 130 10.88 0.20 5600 76 x 115 11.92 0.20 76 x 155 12.80 0.20 6800 76 x 155 14.06 0.20 89 x 155 15.00 0.20 8200 89 x 155 16.43 0.20 89 x 155 16.50 0.20 10000 89 x 155 18.28 0.20 89 x 195 20.00 0.20 12000 89 x 195 21.84 0.20 89 x 235 23.61 0.20 15000 89 x 235 26.31 0.20 Note: 1. Ripple Current: (A/rms) 85°C, 120Hz. 2. Dissipation Factor: 120Hz / 20°C Yageo corporation ELECTROLYTIC CAPACITORS NM [ For Wide Temperature ] Screw Type Aluminum Electrolytic Capacitors Used Large Power Source, Converter Circuit ELECTRICAL CHARACTERISTICS Operating Temperature Range -40 to +105°C -25 to +105°C Rated Voltage Range 25 ~ 100V 160 ~ 450V Capacitance Tolerance ±20% (120Hz, +20°C) Leakage Current I = 0.02CV or 5mA Whichever is smaller. (After 5 Minutes Application of DC Rated Voltage at 20°C) Dissipation Factor at 120Hz, +20°C Description Less than the Value Specified in the Standard Products Tables Endurance After applying rated voltage for 2000 hours at +105°C and then resumed Endurance : 105°C 2000 Hours 16 hours. High Ripple Current, Load Life of 2000 hours at 105°C (a) Capacitance Change: ±20% Initial Measured Value (b) Dissipation Factor: ≤ 2 Times Initial Specified Value Shelf Life (c) Leakage Current: ≤ Initial Specified Value MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient After storage for 1000 hours at +105°C, Ur to be applied for 30 minutes FREQUENCY (Hz) 50 60 100 (120) and then resumed 16 hours. FACTOR 0.80 1.00 (a) Capacitance Change: ±20% Initial Measured Value FREQUENCY (Hz) 300 1K ≥10K (b) Dissipation Factor: ≤ 2 Times Initial Specified Value FACYOR 1.30 1.40 (c) Leakage Current: ≤ Initial Specified Value diagram of dimensions Unit: mm Sleeve F 35 12.7 51 22 63.5 28.6 76 32 89 32 M5x0.8 Safety Vent F ±1 Dø L ±2 20max Dø±1 0.80 1.10 128 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 25 (32) SIZE RIPPLE CURRENT 35 (44) DISSIPATION SIZE FACTOR RIPPLE CURRENT 50 (63) DISSIPATION SIZE FACTOR RIPPLE CURRENT DISSIPATION FACTOR 3300 35 x 50 2.20 0.2 4700 35 x 50 3.30 0.25 6800 35 x 50 2.60 0.30 35 x 80 3.40 0.25 10000 35 x 50 2.90 0.35 35 x 80 3.70 0.30 35 x 80 4.10 0.25 15000 35 x 80 4.20 0.35 35 x 80 4.50 0.30 35 x 100 4.90 0.30 22000 35 x 80 5.10 0.35 35 x 100 5.50 0.35 51 x 75 5.90 0.35 33000 35 x 100 6.30 0.40 51 x 75 6.70 0.40 51 x 115 7.80 0.40 47000 51 x 75 8.00 0.40 51 x 95 8.10 0.45 63.5 x 95 9.50 0.40 68000 51 x 115 10.00 0.50 51 x 115 10.00 0.50 63.5 x 115 11.60 0.45 100000 63.5 x 95 11.30 0.60 63.5 x 115 12.10 0.60 76 x 115 14.10 0.50 150000 63.5 x 115 12.90 0.80 76 x 115 13.80 0.70 89 x 130 18.90 0.50 220000 76 x 115 14.80 1.00 89 x 130 17.60 0.70 330000 89 x 130 19.90 1.00 Note: 1. Ripple Current: (A/rms) 105°C, 120Hz 2. Dissipation Factor: 120Hz / 20°C 129 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 63 (72) SIZE RIPPLE CURRENT 80 (100) DISSIPATION SIZE FACTOR RIPPLE CURRENT 100 (125) DISSIPATION SIZE FACTOR RIPPLE CURRENT DISSIPATION FACTOR 1000 35 x 50 1.40 0.15 1500 35 x 50 1.70 0.15 2200 35 x 50 2.10 0.15 35 x 50 2.10 0.15 35 x 80 2.50 0.15 3300 35 x 50 2.20 0.20 35 x 80 3.00 0.15 35 x 80 3.00 0.15 4700 35 x 80 3.10 0.20 35 x 80 3.60 0.15 35 x 100 3.90 0.15 6800 35 x 80 3.70 0.20 35 x 100 4.00 0.20 51 x 75 5.00 0.15 10000 35 x 100 4.40 0.25 51 x 75 5.20 0.20 51 x 95 6.50 0.15 15000 51 x 75 5.70 0.25 51 x 95 6.20 0.25 63.5 x 95 7.60 0.20 22000 51 x 95 6.80 0.30 63.5 x 95 8.20 0.25 76 x 95 9.70 0.20 33000 63.5 x 95 9.20 0.30 76 x 95 9.70 0.30 76 x 130 11.80 0.25 47000 63.5 x 115 10.90 0.35 76 x 115 12.50 0.30 89 x 130 15.00 0.25 68000 76 x 115 13.00 0.40 89 x 130 16.40 0.30 100000 89 x 130 17.20 0.40 Note: 1. Ripple Current: (A/rms) 105°C, 120Hz 2. Dissipation Factor: 120Hz / 20°C 130 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 160 (200) SIZE RIPPLE CURRENT 200 (250) DISSIPATION SIZE FACTOR 330 RIPPLE CURRENT 250 (300) DISSIPATION SIZE FACTOR RIPPLE CURRENT DISSIPATION FACTOR 35 x 50 0.80 0.15 35 x 50 0.80 0.15 470 35 x 50 1.00 0.15 35 x 50 1.00 0.15 35 x 50 1.00 0.15 680 35 x 50 1.10 0.15 35 x 50 1.10 0.15 35 x 80 1.40 0.15 1000 35 x 80 1.70 0.15 35 x 80 1.70 0.15 35 x 100 1.90 0.15 1500 35 x 80 2.00 0.15 35 x 100 2.20 0.15 51 x 75 2.30 0.15 2200 35 x 100 2.70 0.15 51 x 75 2.80 0.15 51 x 95 3.10 0.15 3300 51 x 80 3.50 0.15 51 x 95 3.70 0.15 63.5 x 95 4.20 0.15 4700 51 x 95 4.40 0.15 63.5 x 95 4.90 0.15 63.5 x 115 5.40 0.15 6800 63.5 x 95 5.90 0.15 63.5 x 115 6.30 0.15 76 x 115 6.90 0.15 10000 76 x 95 7.60 0.15 76 x 115 8.10 0.15 76 x 155 9.30 0.15 15000 76 x 130 10.30 0.15 89 x 130 10.90 0.15 89 x 155 12.20 0.15 22000 89 x 130 13.20 0.15 Note: 1. Ripple Current: (A/rms) 105°C, 120Hz 2. Dissipation Factor: 120Hz / 20°C 131 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 400 (450) SIZE RIPPLE CURRENT DISSIPATION FACTOR 450 (500) SIZE RIPPLE CURRENT DISSIPATION CURRENT 220 35 x 50 1.10 0.15 330 35 x 100 1.50 0.15 470 51 x 80 2.10 0.15 680 51 x 95 2.70 0.15 51 x 100 4.20 0.15 51 x 130 5.70 0.15 63.5 x 115 7.30 0.15 76 x 130 10.10 0.15 76 x 155 12.60 0.15 89 x 155 15.80 0.15 1000 51 x 75 2.50 0.15 1200 51 x 95 3.00 0.15 1500 51 x 115 3.60 0.15 1800 51 x 130 4.10 0.15 2200 63.5 x 95 4.50 0.15 2700 63.5 x 115 5.30 0.15 3300 63.5 x 130 6.20 0.15 3900 63.5 x 155 7.20 0.15 76 x 115 6.80 0.15 63.5 x 195 8.70 0.15 76 x 130 7.80 0.15 63.5 x 195 9.60 0.15 76 x 155 9.20 0.15 6800 89 x 155 10.70 0.15 8200 89 x 155 11.80 0.15 10000 89 x 195 14.10 0.15 4700 5600 Note: 1. Ripple Current: (A/rms) 105°C, 120Hz 2. Dissipation Factor: 120Hz / 20°C Yageo corporation ELECTROLYTIC CAPACITORS Screw Type Aluminum Electrolytic Capacitors NF [ Long Life for Inverter ] Specially For The Demand to Higher Voltage with Compact Size ELECTRICAL CHARACTERISTICS Operating Temperature Range -40 to +85°C Rated Voltage Range 400V, 450V Capacitance Tolerance ±20% (120Hz, +20°C) Leakage Current I = 0.02CV or 5mA Whichever is smaller. (After 5 Minutes Application of DC Voltage at 20°C) Dissipation Factor Description Endurance : 85°C, 5000 Hours Higher Voltage with Compact Size for using in Inverter Endurance 1.10 1.30 1.40 450 0.15 0.15 16 hours. (a) Capacitance Change: ±15% Initial Measured Value (b) Dissipation Factor: ≤ 1.75 Times Initial Specified Value 100(120) 300 1K ≥10K 0.70 0.70 1.00 400 tan δ (c) Leakage Current: ≤ Initial Specified Value Shelf Life After storage for 1000 hours at +85°C, Ur to be applied for 30 minutes and then resumed 16 hours. (a) Capacitance Change: ±15% Initial Measured Value (b) Dissipation Factor: ≤ 1.75 Times Initial Specified Value (c) Leakage Current: ≤ Initial Specified Value diagram of dimensions Sleeve M5x0.8 Safety Vent F ±1 FACTOR 60 Rate Voltage (V) After applying rated voltage for 5000 hours at +85°C and then resumed MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient FREQUENCY (Hz) 50 at 120Hz, +20°C L ±2 20max Dø±1 Unit: mm Dø F 51 22 63.5 28.6 76 32 89 32 101 41.5 133 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 400 (450) SIZE RIPPLE CURRENT DISSIPATION FACTOR 1800 450 (500) SIZE RIPPLE CURRENT DISSIPATION FACTOR 51 x 115 7.60 0.15 2200 51 x 115 8.80 0.15 51 x 130 8.80 0.15 2700 51 x 130 10.20 0.15 63.5 x 95 9.50 0.15 3300 63.5 x 95 11.00 0.15 63.5 x 115 11.20 0.15 3900 63.5 x 115 12.80 0.15 63.5 x 130 12.80 0.15 4700 63.5 x 130 14.80 0.15 76 x 115 14.10 0.15 5600 76 x 115 16.20 0.15 76 x 130 16.20 0.15 6800 76 x 130 18.70 0.15 76 x 155 19.10 0.15 8200 76 x 155 22.00 0.15 76 x 195 23.00 0.15 89 x 130 21.00 0.15 89 x 170 25.70 0.15 89 x 195 29.70 0.15 101 x 175 29.30 0.15 89 x 235 35.90 0.15 101 x 195 34.20 0.15 101 x 235 40.20 0.15 10000 12000 15000 76 x 195 26.70 0.15 89 x 130 24.20 0.15 89 x 155 28.50 0.15 89 x 195 34.80 0.15 18000 89 x 235 41.20 0.15 22000 101 x 235 47.00 0.15 Note: 1. Ripple Current: (A/rms) 85°C, 120Hz 2. Dissipation Factor: 120Hz / 20°C Yageo corporation ELECTROLYTIC CAPACITORS Screw Type Aluminum Electrolytic Capacitors NH [ High Temperature, Long Life for Inverter ] High Ripple Products ELECTRICAL CHARACTERISTICS Operating Temperature Range -40 to +105°C -25 to +105°C Rated Voltage Range 10 ~ 100V 350 ~ 500V Capacitance Tolerance ±20% (120Hz, +20°C) Leakage Current I = 0.02CV or 5mA Whichever is smaller. (After 5 Minutes Application of DC Voltage at 20°C) Description Temperature Characteristics Impedance Ratio at 120Hz 10~100 160~500 Endurance : 105°C 5000 Hours Z -25°C /Z +20°C Ur (V) - 8 For High Ripple Current Product Z -40°C / Z +20°C 12 - Endurance After applying rated voltage for 5000 hours at +105°C and then resumed MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient 16 hours. FREQUENCY (Hz) 50 120 360 1K 10K 50K (b) Dissipation Factor: ≤ 2 Times Initial Specified Value 10~50V 0.95 1.00 1.03 1.05 1.09 1.12 (c) Leakage Current: ≤ Initial Specified Value 63~100V 0.90 1.00 1.06 1.10 1.18 1.22 100~250V 0.80 1.00 1.12 1.22 1.30 1.33 and then resumed 16 hours. 350~500V 0.80 1.00 1.20 1.50 1.60 1.70 (a) Capacitance Change: ±20% Initial Measured Value (a) Capacitance Change: ±20% Initial Measured Value Shelf Life After storage for 1000 hours at +105°C, Ur to be applied for 30 minutes (b) Dissipation Factor: ≤ 2 Times Initial Specified Value (c) Leakage Current: ≤ Initial Specified Value diagram of dimensions Unit: mm Hexagonal Headed Bolt Sleeve L±α max 1±1 D+2 max W±1 Bottom Plate Dø W I α NOMINAL DIA. OF BOLT 51 22 6 3 M5 63.5 28.6 6 3 M5 76 31.8 6 3 M5 90 31.8 6 3 M5 135 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. RATED VOLTAGE W V (SURGE VOLTAGE W V) (μF) 10 (13) SIZE 16 (20) RIPPLE DISSIPATION SIZE CURRENT FACTOR 25 (32) RIPPLE DISSIPATION SIZE CURRENT FACTOR D x L: mm 35 (44) RIPPLE DISSIPATION SIZE CURRENT FACTOR RIPPLE DISSIPATION CURRENT FACTOR 8200 35 x 80 3.0 0.30 10000 35 x 80 3.3 0.30 12000 35 x 80 3.3 0.35 35 x 80 3.6 0.30 15000 35 x 50 2.9 0.45 35 x 80 3.7 0.35 35 x 80 4.1 0.30 18000 35 x 80 3.5 0.45 35 x 80 4.0 0.35 35 x 100 4.8 0.30 22000 35 x 80 3.9 0.45 35 x 80 4.5 0.35 35 x 120 5.2 0.35 27000 35 x 80 4.3 0.45 35 x 80 4.3 0.45 35 x 100 5.0 0.40 51 x 80 5.9 0.40 33000 35 x 80 4.7 0.45 35 x 100 4.8 0.50 35 x 120 5.9 0.40 51 x 100 6.6 0.40 39000 35 x 80 5.3 0.45 35 x 100 5.3 0.50 51 x 80 6.5 0.40 51 x 120 7.8 0.40 47000 35 x 100 6.1 0.45 35 x 120 6.2 0.50 51 x 100 7.9 0.40 51 x 120 8.0 0.45 56000 35 x 100 6.2 0.50 51 x 80 6.3 0.60 51 x 120 8.8 0.40 63.5 x 100 9.2 0.45 68000 35 x 120 6.8 0.60 51 x 100 7.6 0.60 51 x 120 9.1 0.50 63.5 x 120 11.0 0.45 82000 51 x 80 7.8 0.60 51 x 120 8.3 0.70 63.5 x 100 10.6 0.50 76.2 x 120 12.7 0.50 100000 51 x 100 8.5 0.70 51 x 120 9.2 0.70 63.5 x 120 11.4 0.60 76.2 x 140 13.5 0.60 120000 51 x 100 9.5 0.70 63.5 x 100 9.9 0.80 76.2 x 100 12.8 0.60 90 x 140 16.1 0.60 150000 63.5 x 100 11.0 0.80 76.2 x 100 12.3 0.80 76.2 x 120 13.7 0.75 180000 63.5 x 100 12.1 0.80 76.2 x 120 14.5 0.80 76.2 x 140 16.1 0.76 220000 76.2 x 100 13.2 1.00 76.2 x 140 15.2 1.00 90 x 140 16.6 1.00 270000 76.2 x 120 14.4 1.20 90 x 140 16.8 1.20 330000 76.2 x 140 17.0 1.20 390000 90 x 140 18.6 1.40 Note: 1. Max. Allowable Ripple Current: (A/rms) 105°C, 120Hz 2. Dissipation Factor: 120Hz / 20°C 136 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. RATED VOLTAGE W V (SURGE VOLTAGE W V) (μF) 50 (63) SIZE 63 (79) RIPPLE DISSIPATION SIZE CURRENT FACTOR D x L: mm 80 (100) 100 (125) RIPPLE DISSIPATION SIZE RIPPLE DISSIPATION SIZE RIPPLE DISSIPATION CURRENT FACTOR CURRENT FACTOR CURRENT FACTOR 1200 35 x 50 1.4 0.15 1500 35 x 80 1.6 0.15 1800 35 x 80 1.8 0.15 2200 35 x 50 1.9 0.15 35 x 80 2.0 0.15 2700 35 x 50 1.9 0.19 35 x 80 2.2 0.15 35 x 80 2.4 0.15 3300 35 x 50 2.1 0.15 35 x 80 2.5 0.15 35 x 100 2.8 0.15 3900 35 x 50 2.0 0.20 35 x 80 2.7 0.20 35 x 80 2.9 0.15 35 x 120 3.1 0.15 4700 35 x 50 2.2 0.25 35 x 80 2.9 0.20 35 x 100 3.1 0.15 51 x 80 3.6 0.15 5600 35 x 80 2.8 0.25 35 x 80 3.2 0.20 35 x 100 3.6 0.15 51 x 100 4.3 0.15 6800 35 x 80 3.0 0.25 35 x 80 3.5 0.20 35 x 120 4.1 0.20 51 x 120 5.0 0.15 8200 35 x 80 3.3 0.25 35 x 100 4.2 0.25 51 x 80 4.8 0.20 51 x 120 5.5 0.15 10000 35 x 80 3.7 0.25 35 x 120 4.3 0.25 51 x 100 5.6 0.20 63.5 x 100 6.4 0.15 12000 35 x 100 4.4 0.25 51 x 80 4.8 0.25 51 x 100 6.1 0.20 63.5 x 120 6.6 0.20 15000 35 x 120 4.7 0.30 51 x 100 5.9 0.25 51 x 120 7.4 0.20 76.2 x 100 7.5 0.20 18000 51 x 80 4.8 0.35 51 x 120 6.3 0.30 63.5 x 120 8.0 0.25 76.2 x 120 8.0 0.25 22000 51 x 100 5.9 0.35 51 x 120 6.7 0.30 76.2 x 100 9.1 0.25 76.2 x 140 9.4 0.25 27000 51 x 120 7.0 0.35 63.5 x 120 8.8 0.30 76.2 x 120 9.7 0.30 90 x 140 10.4 0.30 33000 63.5 x 100 7.6 0.40 76.2 x 120 10.0 0.35 76.2 x 140 11.5 0.30 39000 63.5 x 120 8.9 0.40 76.2 x 140 12.5 0.35 90 x 140 12.5 0.30 47000 63.5 x 120 9.8 0.40 90 x 140 13.8 0.40 56000 76.2 x 120 11.9 0.40 68000 76.2 x 140 13.1 0.45 82000 90 x 140 14.8 0.50 Note: 1. Max. Allowable Ripple Current: (A/rms) 105°C, 120Hz 2. Dissipation Factor: 120Hz / 20°C 137 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS D x L: mm CAP. RATED VOLTAGE W V (SURGE VOLTAGE W V) (μF) 160 (200) 200 (250) 250 (300) 350 (400) SIZE RIPPLE DISSIPATION SIZE RIPPLE DISSIPATION SIZE RIPPLE DISSIPATION SIZE RIPPLE DISSIPATION CURRENT FACTOR CURRENT FACTOR CURRENT FACTOR CURRENT FACTOR 330 35 x 50 0.7 0.15 390 35 x 80 0.8 0.15 470 35 x 50 0.9 0.15 35 x 80 0.9 0.15 560 35 x 80 1.0 0.15 35 x 80 1.0 0.15 680 35 x 50 1.1 0.15 35 x 80 1.1 0.15 35 x 100 1.2 0.15 820 35 x 80 1.2 0.15 35 x 80 1.3 0.15 35 x 100 1.4 0.15 1000 35 x 80 1.3 0.15 35 x 80 1.5 0.15 35 x 120 1.6 0.15 1200 35 x 80 1.5 0.15 35 x 100 1.7 0.15 51 x 80 1.8 0.15 1500 35 x 80 1.7 0.15 35 x 120 1.9 0.15 51 x 100 2.2 0.15 1800 35 x 100 2.0 0.15 35 x 120 2.2 0.15 51 x 120 2.6 0.15 2200 35 x 120 2.3 0.15 51 x 80 2.7 0.15 51 x 120 2.8 2700 35 x 120 2.7 0.15 51 x 100 3.2 0.15 63.5 x 100 3.3 51 x 81 3.3 0.25 51 x 90 5.2 0.25 0.15 51 x 100 7.0 0.25 0.15 51 x 130 8.4 0.25 63.5 x 90 8.1 0.25 3300 51 x 100 3.3 0.15 51 x 120 3.5 0.15 63.5 x 120 4.0 0.15 51 x 150 9.9 0.25 3900 51 x 120 3.8 0.15 63.5 x 100 4.0 0.15 76.2 x 100 4.4 0.15 63.5 x 130 11.5 0.25 76.2 x 90 10.8 0.25 4700 51 x 120 4.2 0.15 63.5 x 120 4.7 0.15 76.2 x 120 5.2 0.15 5600 51 x 120 4.7 0.15 76.2 x 100 5.3 0.15 76.2 x 140 6.1 0.15 63.5 x 150 14.7 0.25 6800 63.5 x 120 5.7 0.15 76.2 x 120 6.3 0.15 90 x 140 7.4 0.15 76.2 x 130 16.8 0.25 8200 76.2 x 100 6.4 0.20 76.2 x 140 6.4 0.20 76.2 x 150 19.6 0.25 10000 76.2 x 120 6.8 0.20 90 x 140 7.7 0.20 76.2 x 190 23.0 0.25 12000 76.2 x 140 7.8 0.20 15000 90 x 140 9.5 0.20 90 x 190 30.6 0.25 90 x 270 43.5 0.25 22000 Note: 1. Max. Allowable Ripple Current: (A/rms) 105°C, 120Hz 2. Dissipation Factor: 120Hz / 20°C 138 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. RATED VOLTAGE W V (SURGE VOLTAGE W V) (μF) 400 (450) SIZE RIPPLE CURRENT 450 (500) DISSIPATION SIZE FACTOR RIPPLE CURRENT 500 (550) DISSIPATION SIZE FACTOR 470 560 680 51 x 80 51 x 80 3.0 2.6 4.7 2200 2700 3300 51 x 110 6.3 0.25 0.25 8200 3.6 0.20 4.0 0.25 51 x 110 4.4 0.20 51 x 110 4.8 0.25 51 x 130 5.2 0.20 63.5 x 90 5.0 0.20 51 x 150 6.3 0.20 63.5 x 110 6.8 0.20 51 x 130 6.4 0.25 63.5 x 90 6.2 0.25 51 x 150 7.6 0.25 63.5 x 90 7.3 0.25 63.5 x 100 7.5 0.25 51 x 150 8.9 0.25 63.5 x 130 8.9 0.25 63.5 x 150 9.6 0.20 63.5 x 110 8.8 0.25 76.2 x 90 8.4 0.25 76.2 x 110 9.2 0.20 63.5 x 130 10.5 0.25 63.5 x 150 10.6 0.25 76.2 x 90 9.9 0.25 76.2 x 110 10.2 0.25 76.2 x 130 11.9 0.25 76.2 x 150 12.7 0.20 90 x 130 11.9 0.20 90 x 190 18.8 0.20 90 x 270 26.8 0.20 63.5 x 150 13.4 0.25 76.2 x 130 13.9 0.25 76 x 150 14.0 0.25 90 x 130 14.2 0.25 76.2 x 150 17.9 0.25 76.2 x 190 17.3 0.25 90 x 130 17.2 0.25 90 x 150 16.7 0.25 76.2 x 190 20.8 0.25 90 x 150 20.1 0.25 90 x 190 22.8 0.25 90 x 270 32.8 0.25 90 x 190 27.4 0.25 15000 22000 51 x 90 0.25 10000 12000 0.20 7.5 5600 6800 2.4 51 x 130 3900 4700 51 x 80 51 x 90 1500 1800 DISSIPATION FACTOR 0.25 1000 51 x 90 RIPPLE CURRENT 0.25 820 1200 D x L: mm 90 x 270 39.4 0.25 Note: 1. Max. Allowable Ripple Current: (A/rms) 105°C, 120Hz 2. Dissipation Factor: 120Hz / 20°C Yageo corporation ELECTROLYTIC CAPACITORS NG [ For Low Voltage, Large Capacity ] Screw Type Aluminum Electrolytic Capacitors Low Leakage Current, Small Size and High Ripple Current ELECTRICAL CHARACTERISTICS Operating Temperature Range -40 to +85°C Rated Voltage Range 10 ~ 100V Capacitance Tolerance ±20% (120Hz, 20°C) Leakage Current D = 35mm I ≤ 0.02CV (μA) or 4mA (at 20°C, After 2 Minutes, Whichever is smaller.) D ≥ 51mm I ≤ 0.03CV (μA) or 6mA Description (at 20°C, After 2 Minutes, Whichever is smaller.) Endurance After applying rated voltage with specified ripple current for 2000 hours at +85°C and then resumed 16 hours. Endurance : 85°C 2000 Hours Low Voltage (≤ 100V), Large Capacitance, Lug or Screw Type, Low Dissipation Factor (a) Capacitance Change: ±15% Initial Measured Value (b) Dissipation Factor: ≤ 2 Times Initial Specified Value (c) Leakage Current: ≤ Initial Specified Value Shelf Life After storage for 1000 hours at +85°C and then resumed 16 hours. (a) Capacitance Change: ±15% Initial Measured Value (b) Dissipation Factor: ≤ 2 Times Initial Specified Value (c) Leakage Current: ≤ Initial Specified Value diagram of dimensions L 35 12 50, 60, 80, 100, 120 51 22 80, 100, 120 63.5 28 100, 120, 140 76 32 100, 120, 140 89 32 140 Vlnyl Vent Safety Sleeve Sleeve M5x0.8 Negative Safety Vent F ±1 F F±1 Dø Unit: mm L ±2 10max Dø±1 L ±2 20max Dø±1 140 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 6.3 (8) SIZE RIPPLE CURRENT 10 (13) DISSIPATION SIZE FACTOR RIPPLE CURRENT 16 (20) DISSIPATION SIZE FACTOR 22000 RIPPLE CURRENT DISSIPATION FACTOR 35 x 50 4.50 0.50 33000 35 x 50 4.20 0.75 35 x 80 6.40 0.50 47000 35 x 80 6.20 0.75 35 x 100 8.20 0.50 68000 35 x 100 8.00 0.75 35 x 120 10.50 0.50 100000 35 x 120 10.40 0.75 51 x 80 10.70 0.75 150000 51 x 80 11.30 1.00 51 x 120 14.80 0.75 220000 51 x 120 15.50 1.00 63.5 x 120 17.00 1.00 330000 63.5 x 120 17.00 1.50 76 x 120 14.80 1.50 470000 76 x 120 21.90 2.00 63.5 x 140 35 1.50 76 x 140 30 1.50 1000000 63.5 x 140 40.00 Note: 1. Ripple Current: (A/rms) 85°C, 120Hz 2. Dissipation Factor: 120Hz / 20°C 1.50 141 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 25 (32) SIZE RIPPLE CURRENT 35 (44) DISSIPATION SIZE FACTOR RIPPLE CURRENT 50 (63) DISSIPATION SIZE FACTOR 6800 10000 RIPPLE CURRENT DISSIPATION FACTOR 35 x 50 3.60 0.25 35 x 50 4.30 0.25 35 x 60 4.70 0.25 15000 35 x 50 4.40 0.35 35 x 80 6.20 0.25 35 x 80 6.20 0.25 22000 35 x 80 6.30 0.35 35 x 100 8.00 0.25 51 x 80 7.30 0.35 33000 35 x 100 8.30 0.35 51 x 80 9.00 0.35 51 x 80 9.00 0.35 47000 51 x 80 8.90 0.50 51 x 100 11.50 0.35 51 x 100 11.50 0.35 68000 51 x 80 10.80 0.50 51 x 120 14.60 0.35 63.5 x 100 12.70 0.50 100000 51 x 120 14.80 0.50 63.5 x 100 15.40 0.50 76 x 100 16.60 0.50 150000 63.5 x 120 16.20 0.75 76 x 120 21.40 0.50 220000 76 x 120 21.20 0.75 1000000 89 x 140 28.00 0.75 Note: 1. Ripple Current: (A/rms) 85°C, 120Hz 2. Dissipation Factor: 120Hz / 20°C 142 CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS CAP. (μF) D x L: mm RATED VOLTAGE W V (SURGE VOLTAGE W V) 63 (72) SIZE RIPPLE CURRENT 80 (100) DISSIPATION SIZE FACTOR RIPPLE CURRENT 100 (125) DISSIPATION SIZE FACTOR RIPPLE CURRENT DISSIPATION FACTOR 2200 35 x 50 2.10 0.25 3300 35 x 80 3.00 0.25 4700 35 x 50 3.00 0.25 35 x 80 3.40 0.25 35 x 100 3.90 0.25 6800 35 x 60 3.90 0.25 35 x 80 4.30 0.25 35 x 120 4.90 0.25 10000 35 x 80 5.10 0.25 35 x 100 4.20 0.25 51 x 80 6.00 0.25 51 x 80 6.00 0.30 15000 51 x 80 6.70 0.35 51 x 100 7.00 0.30 51 x 120 8.30 0.25 22000 51 x 80 7.40 0.35 63.5 x 100 7.80 0.35 63.5 x 120 9.10 0.35 33000 51 x 100 9.70 0.35 76 x 100 10.50 0.40 76 x 120 12.00 0.35 47000 63.5 x 100 10.50 0.50 76 x 120 13.50 0.40 100000 63.5 x 120 13.4 0.50 Note: 1. Ripple Current: (A/rms) 85°C, 120Hz 2. Dissipation Factor: 120Hz / 20°C YAGEO - A GLOBAL COMPANY ASIA Chengdu, China Chongqing, China Dongguan, China Hong Kong, China Tel. +86 27 5983 8939 Fax. +86 27 5983 8939 Tel. +86 27 5983 8939 Fax. +86 27 5983 8939 Tel. +86 769 8772 0275 Fax. +86 769 8791 0053 Tel. +852 2342 6833 Fax. +852 2342 6588 Mudu, China Qingdao, China Suzhou, China Wuhan, China Tel. +86 512 6651 8889 Fax. +86 512 6651 9889 Tel. +86 532 8797 0533 Fax. +86 532 8797 0533 Tel. +86 512 6825 5568 Fax. +86 512 6825 5386 Tel. +86 27 5983 8939 Fax. +86 27 5983 8939 Tokyo, Japan Seongnam, Korea Kuala Lumpur, Malaysia Singapore Tel. +81 3 6809 3972 Fax. +81 3 6809 3982 Tel. +82 31 712 4797 Fax. +82 31 712 5866 Tel. +60 3 8063 8864 Fax. +60 3 8063 7376 Tel. +65 6244 7800 Fax. +65 6244 4943 Taipei, Taiwan Tel. +886 2 6629 9999 Fax. +886 2 2917 4286 EUROPE Roermond, Benelux Suresnes, France Hamburg, Germany Munich, Germany Tel. +31 475 385 555 Fax. +31 475 385 589 Tel. +33 1 46 14 87 91 Fax. +39 02 6601 7490 Tel. +49 4121 870 189 Fax. +49 4121 870 271 Tel. +49 8999 216 552 Fax. +49 8999 216 200 Szombathely, Hungary Milan, Italy Moscow, Russian Federation Surrey, UK Tel. +36 94 517 702 Fax. +36 94 517 701 Tel. +39 02 6129 1017 Fax. +39 02 6601 7490 Tel. +7 916 625 92 38 Fax. +7 498 610 07 07 Tel. +44 7831 79 7754 Fax. +31 475 385 589 NORTH AMERICA San Jose, U.S.A. Tel. +1 408 240 6200 Fax. +1 408 240 6201 For a complete listing of all Yageo sales offices, distributors, and representatives, please visit "contact us" at www.yageo.com © YAGEO Corporation All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. Printed in Taiwan Document order number: 2838 100 00114 Date of release: April 2009