1000uF 25V

www.yageo.com RoHS Compliant
ISO-9001:2000 CERTIFIED
ELECTROLYTIC CAPACITORS
INDEX
MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS
27 S5 [ For Super Miniature ]
1,000hrs. at105°C
29 SS [ For Super Miniature ]
1,000hrs. at105°C
31 SK [ For General ]
2,000hrs. at 85°C
36 SE-K [ For General ]
1,000hrs. at105°C
41 SH [ For General ]
2,000hrs. at105°C
45 SG [ Electronic Ballast ]
5,000hrs. at105°C
48 SP [ Miniature and Long Life ]
10,000hrs. at105°C
50 SB [ For Low Leakage Current ] 1,000hrs. at105°C
54 SN [ For Non-Polar ] 1,000hrs. at105°C
58 SR [ For Horizontal Deflection ] 1,000hrs. at105°C
60 SC [ Low Impedance and Low ESR Suitable for Motherboard Output Termination ]
3,000hrs. at105°C
64 SJ [ Low Impedance and High Ripple Series ]
1,000~5,000hrs. at105°C
69 SQ [ For Adapter and Power Supply Applications Series ]
2,000hrs. at105°C
72 SY [ For Low Impedance and Low ESR Suitable for Motherboard Output Termination ] 3,000~6,000hrs. at105°C
78 SZ [ Ultra Low ESR ]
80 ST [ Low Impedance and Long Life ]
2,000hrs. at105°C
4,000~10,000hrs. at105°C
83 SD [ For High Ripple Current ]
85 SL [ Long Life and Low Impedance ]
5,000hrs. at105°C
3,000~7,000hrs. at105°C
92 SU [ For Higher Temperature Range ]
94 SW [ Higher Temperature Range and Long Life ]
2,000hrs. at125°C
2,000~5,000hrs. at125°C
LARGE CAN ALUMINUM ELECTROLYTIC CAPACITORS
97 LH [ For Miniature ]
2,000hrs. at 85°C
106 LG [ For General ]
2,000hrs. at105°C
114 LV [ For Long Life ]
3,000hrs. at105°C
121 LC [ High Temperature and Long Life ]
5,000hrs. at105°C
SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS
124 CA [ For General ]
2,000hrs. at 85°C
128 CB [ For General ]
1,000hrs. at105°C
132 CE [ For Long Life ]
2,000hrs. at105°C
136 CZ [ For Low Impedance ] 1,000hrs. at105°C
140 CD [ For Ultra Low Impedance ]
2,000hrs. at105°C
143 CH [ Ultra Low Impedance and High Temperature ]
2,000hrs. at125°C
146 CX [ Ultra Low Impedance and Long Life ]
3,000~5,000hrs. at105°C
CONDUCTIVE POLYMER SOLID CAPACITORS
149 CP [ Ultra Low ESR & High Ripple Current ]
2,000hrs. at105°C
151 CG [ Low ESR & High Ripple Current ]
2,000hrs. at105°C
SCREW TYPE ALUMINUM ELECTROLYTIC CAPACITORS
154 NP [ For General ]
2,000hrs. at 85°C
159 NM [ For Wide Temperature ]
2,000hrs. at105°C
164 NF [ Long Life for Inverter ]
5,000hrs. at 85°C
166 NH [ High Temperature, Long Life for Inverter ]
5,000hrs. at105°C
171 NG [ For Low Voltage, Large Capacity ]
2,000hrs. at 85°C
4
PRECAUTIONS IN USING ALUMINUM ELECTROLYTIC CAPACITORS
Please note the following recommendations when using capacitors:
1. When using Electrolytic capacitors on DC applications, polarization
is required as well as the confirmation of the polarity of the course.
9. Do not apply excessive force to the lead wires or terminals. It may
break the components or disconnect the internal elements on the
board. (For strength of terminals, please refer to JIS C5102 and C5141.)
Otherwise, the circuit life may be shortened or the capacitor may be
damaged by the insertion on reverse polarity.
10. Keep the clearance between the vent of the capacitor and the case of
Use non-polar capacitors on those circuits with occasionally reverse
the appliance. Do not block the operation of the vent, unless otherwise
polarity or unknown polarity. Also note that do not use electrolytic
described on the catalogues or product specifications. The narrower
capacitors for AC applications.
clearance may adversely affect the vent operation and result in the
capacitor explosion.
2. Do not apply a voltage exceeding the capacitor rated voltage, that will
cause the capacitor be damaged by increased leakage current.
Case of the application
3. Use the electrolytic capacitor at current value under the permissible
ripple range.
Critical space between top
(cap) and case
Clearance
4. Use the electrolytic capacitors according to the specified operation
Board
temperature range. Using at room temperature will ensure a longer life.
5. The electrolytic capacitor is not suitable for circuits which are charged
and discharged repeatedly. If used in circuits which are charged and
discharged repeatedly, the capacitance value may drop or the capacitor
Case diameter
Clearance
6.3ø to 16ø mm
2 mm minimum
18ø to 35ø mm
3 mm minimum
40ø mm & up
5 mm minimum
Fig.1-1
may be damaged. Please consult our engineering department for
assistance in these applications.
6. When capacitors have been left unused for a long time, use them only
Attention
after due voltage treatments. Long storage time may raise capacitor's
• The description in this catalogue is subject to change without prior
leakage current level. In such cases, be sure to provide the necessary
notice for product improvement. Therefore, please confirm the
voltage treatment before use.
specification before ordering products.
• The general characteristics, reliability data, etc., described in this
7. Be careful of the temperature and time conditions when soldering.
Adverse effects may happen on the electrical characteristics and
insulation sleeve of electrolytic capacitors may occur in case the
soldering temperature is too high or dipping time too long. For
small-size electrolytic capacitors, proper dipping shall be executed at
temperature lower than 260°C for less than 10 seconds.
8. Clean circuit boards after soldering. Halogenated hydrocarbon cleaning
solvents are not recommended to clean capacitors with exposed end
seals. If halogenated solvent is required, order and use capacitors in
Epoxy-coated end seals.
catalogue should not be construed as guaranteed values; they are
merely standard values.
• Before using the products, please read the notes in this catalogue
carefully for proper use.
5
Technical Concepts
The Material and Structure of Electrolytic Capacitors
4. Winding: The stitching or cold welding of cut anode and cathode foils
Electrolytic Capacitor is a simple module. It simply contains an insulator
and tab terminal, and wrap the electrolytic paper in between the anode
between relative conductors in an electrode. The major internal raw
and cathode, then fix the end with glue or sticky tape, and attached
material contains an element constructed by an separator paper wrap
leads is called the capacitor "element".
around the anode foil and cathode foil, which is then impregnated with the
5. Impregnation: The process of eliminating the water from the elements
electrolyte, inserted into an aluminum case and sealed.
by pressurizes or vacuum in order to soak the element with the
electrolyte is called Impregnation. The elements fully filled with
Rivent
Lead Wire
Rubber Seal
Anode Foil
Separator Paper
Cathode Foil
Aluminum Case
Vinyl Sleeve
Sleeve Aluminum Case
Element
Terminal
Washer
Lead Tab
Anode Foil
Separator Paper
Cathode Foil
Separator Paper
Bottom Plate
Safe Device
Safe Device
( For Dia, >10mm )
Rubber Seal
6. Assembly: The elements are sealed with rubber to stop the leakage of
electrolyte then put into a sleeve to form the final product.
7. Aging: The purpose of aging is to repair the oxide layer damage by
recharging and electrolyte.
Separator Paper
Anode Foil
Cathode Foil
Aluminum Case
Isolator
Terminals
Fig.1-2
Production Processes
1. Etching: The process to increase surface area of aluminum foil by using
chemical erosion or chemical corrosion method is called Etching.
Normally chemical corrosion method uses the ripple current of
electrolyte, combination of the liquid and temperature to determine the
size, shape, and quantity of the dense network of microscopic channels
on the aluminum foil surface.
2. Forming: The production process of the anode aluminum foil of
electrolytic capacitors is by anodic oxidation of the etched aluminum
foil. The production of the cathode aluminum foil sometimes involves
oxidation in special purposes. This anodic oxidation process is called
Forming. Boric acid or organic acid is used for high voltage forming and
phosphoric acid or ammonium adipose is used for low voltage forming
in order to obtain stable natural oxide layer of Al2O3.
3. Slitting: The cutting of the aluminum foil and separator paper according
to the required length.
electrolyte is then centrifuged to remove excess electrolyte.
6
The Function of Electrolytic Capacitors
The electrolytic capacitors could be widely used in appliance (ie. TV, radio,
For AC Voltage:
audio equipment, washing machine and air conditioner…etc.), computer
1. For Power Improving: Connect the end loading of layout transporting &
equipment (motherboard, image device & the peripherals such as the
electrolytic capacitor for power improving.
printer, drawing device, scanner... etc.), communication equipment, estate
equipment, measuring instrument and also the industrial instrument, air
plane, firebomb, satellite…etc. as a piloting equipment.
2. For Wave Filter: Prevention of external interference in SCR circuit, use
the LC wave filter circuit to inhibit or erase the interference.
* According to the inflict electric wave & using purpose, it basically with
some classified purposes as below:
3. For Phase Across: Phase change of the inductive electromotor (motor)
with single phase.
DC Voltage:
1. For Momentary High Voltage: For using to the impulse generator such
as the shock wave resistance test of the heavy electric machine.
2. For High Electric Current: For using to the welding machine, X-Ray
facility, copy machine and discharge-processing device.
3. For DC High Voltage: The electrolytic capacitor and rectifier composing,
a special DC high voltage been happened after charged, for using to the
power of electronic microscope and accelerator.
4. For Integration & Memory: For either memory circuit or compare
circuit inside the calculator.
The DC Voltage that with Alternate Ingredient:
1. For Wave Filter: Combination with the chip resistor & inductor as a
internet, to be passed by DC current or some frequency to closure or
decline some other frequency.
2. For Bypass: A parallel track that outside from the circuit element, the
IC (integrated circuit) has been rapidly developed in these years and
thus a miniaturization or chip of electrolytic capacitors for bypass was
conduced.
3. For Coupling: Combination of the electrolytic capacitor, chip resistor
and inductor and thus coupling together.
4. For Arising of Toothed Wave: Composing of RC charge/discharge circuit
through the electrolytic capacitor as well as the resistor to generate a
toothed wave to be created.
5. For Reverse (Change) of Circuit: The equipment for changing the AC
voltage to DC voltage.
7
Basic Electrical Characteristics
Capacitance (ESC)
Dissipation Factor (tan )
The capacitive component of the equivalent series circuit (equivalent series
The dissipation factor is the ratio between the active and the reactive
capacitance ESC) is determined by applying an alternate voltage of 0.5V at
power for a sinusoidal waveform voltage. It can be considered as a
a frequency of 120 Hz.
measurement of the gap between an actual and an ideal capacitor.
L
R
C
C = Capacitance (F)
R = Equivalent series resistance (Ω)
L = Equivalent series inductance (H)
reactive
Fig.1-3 Simplified equivalent circuit diagram of an electrolytic capacitor
ideal
D.F. = tan δ x 100 (%) = ωCR x 100 (%)
= 2π fCR x 100 (%)

actual
• Temperature Dependence of the Capacitance
The capacitance of an electrolytic capacitor depends on the
temperature. With decreasing temperature, the viscosity of the
electrolyte increases and reduces its conductivity which leads to the
where: R = Equivalent Series Resistance
C = Equivalent Series Capacitance
W = 2π f
active
Fig. 1-6 The tan is measured with the same set up as for the series
capacitance ESC
capacitance decrease. Furthermore temperature drifts cause armature
dilatation and therefore capacitance changes (up to 20%, depending
on the series considered, from 0 to 80 °C). This phenomenon is more
DF
evident on electrolytic capacitors than other types.
CAP
Temperature(°C)
Fig. 1-7 Dissipation Factor vs. Temperature
Temperature(°C)
Frequency Dependence of the Capacitance
The effective capacitance value is derived from the impedance curve,
as long as the impedance is still in the range where the capacitance
component is dominant.
C=
1
2πfZ
Frequency
Fig. 1-8 Dissipation Factor vs. Frequency
C = Capacitance (F)
f = Frequency (Hz)
Z = Impedance (Ω)
CAP
•
DF
Fig. 1-4 Capacitance Change vs.Temperature
Frequency
Fig. 1-5 Capacitance Change vs. Frequency
8
Basic Electrical Characteristics
Equivalent Series Resistance (ESR)
Co= Aluminum oxide capacitance (surface and thickness of the dielectric).
The equivalent series resistance is the resistive component of the equivalent
Re = Resistance of electrolyte and paper mixture (other resistances not
series circuit. The ESR value depends on frequency and temperature and is
depending on the frequency are not considered: tabs, plates, and so
related to the tan δ by the following equation:
on).
Ce= Electrolyte soaked paper capacitance.
L = Inductive reactance of the capacitor winding and terminals.
ESR =
ESR =
tanδ =
ESC =
f =
tanδ
2πfESC
Equivalent Series Resistance (Ω)
Dissipation Factor
Equivalent Series Capacitance (F)
Frequency (Hz)
The impedance of an electrolytic capacitor changes depending on the
frequency and the temperature.
The impedance as a function of frequency (sinusoidal waveform) under a
The tolerance limits of the rated capacitance must be taken into account
certain temperature can be represented as follows:
when calculating this value.
Z (ohm)
1000
100
ESR
1/ω Ce
B
10
Re
ωL
A
1
Temperature(°C)
1/ω Ce
0.1
Fig. 1-9 ESR Change vs. Temperature
0.1
1
10
100
1000
Fig. 1-12
10000
F (KHz)
The resistance of the electrolyte decreases strongly with increasing
1. Capacitive reactance predominates at low frequencies
temperature.
2. With increasing frequency, the capacitive reactance Xc=1/ω Co
decreases until it reaches the order of magnitude of the electrolyte
ESR
resistance Re (A)
3. At even higher frequencies, the resistance of the electrolyte
predominates: Z = Re (A-B)
Frequency
Fig. 1-10 ESR Change vs. Frequency
4. When the capacitor's resonance frequency is reached (ω0), capacitive
and cancel each other 1/ω conducive reactance mutually cancel each
other 1/ω Ce = ωL, ω0 = SQR (1/LCe) (C)
Impedance (Z)
The impedance of an electrolytic capacitor results from below circuit
formed by the following individual equivalent series components.
5. Above this frequency, the inductive reactance of the winding and its
terminals (Xl = Z = ωL) becomes effective and leads to an increase in
Co
Re
Ce
impedance. Generally speaking it can be estimated that Ce≒0.01 Co
L
Fig. 1-11
9
Basic Electrical Characteristics
The impedance as a function of frequency (sinusoidal waveform) for
I
different temperature values can be represented as follows (typical values):
Z (ohm)
1000
10 µF/450Vdc
100
VR
-40°C
10
VS
VF
V
Fig. 1-14
20°C
Where:
85°C
1
VF = Forming Voltage
If this level is exceeded, a large quantity of heat and gas will be generated
0.1
0.1
1
10
100
1000
Fig. 1-13
10000
F (KHz)
and the capacitor could be damaged.
VR = Rated Voltage
This level represents the top of the linear part of the curve.
VS = Surge Voltage
Re is the most temperature dependant component of electrolytic
It lies between VR and VF: the capacitor can be applied with Vs for short
capacitor equivalent circuit. The electrolyte resistivity will decrease when
periods only.
the temperature rises. In order to obtain a low impedance value in all
temperature range. Re must be as little as possible, but too low Re values
means a very aggressive electrolyte and a shorter life of the electrolytic
capacitor at the high temperatures. A compromise must be reached.
Leakage Current (L.C.)
Due to the aluminum oxide layer that serves as a dielectric, a small current
will continue to flow even after a DC voltage has been applied for long
periods. This current is called leakage current. A high leakage current flows
after applying a voltage to the capacitor and then decreases in few minutes
(e.g. after a prolonged storage without any applied voltage). In the course
of the continuous operation, the leakage current will decrease and reach
an almost constant value. After a voltage free storage the oxide layer may
deteriorate, especially at high temperature. Since there are no currents to
transport oxygen ions to the anode, the oxide layer is not regenerated.
The result is that a higher than normal leakage current will flow when a
voltage is applied after prolonged storage. As the oxide layer is regenerated
in use, the leakage current will gradually decrease to its normal level.
The relationship between the leakage current and the voltage applied at
constant temperature can be shown schematically as follows.
10
Reliability
Bathtub Curve
1. Initial Failure Period
Aluminum electrolytic capacitors failure rates are shown by the following
Deficient Capacitors include any products before dispatch that may
bathtub curve.
have some deficiency caused by the design, production process or use
in inappropriate environments.
2
1
3
2. Random Failure Period
The capacitors have a low defect ratio in the period after it has been
Failure Rate
stabilized.
3. Wear Out Failure Period
The performance of capacitors will decrease with an increase in usage
period. The malfunction rate may vary due to the structural design.
Time
Fig. 1-15 Bathtub Curve
Table-1 Failure Modes and Causes
Failure Modes
Short Circuit
Primary Factors
Internal Causes
Mismanaged
Production
Short Circuit
Between Electrodes
Burred Foil /
Metal Particle
Dielectrical Break of
Oxide Layer
Local Deficiency in
Oxide Layer
Dielectrical Break of
Separator
Open Circuit
Mishandled
Application
Mechanical Stress
Disconnection of
Terminal Construction
Mechanical Stress
Poor Terminal
Connection
Poor Connection
Deterioration with Time
Electrolyte Vaporization
Excessive
Thermal Stress
tanδ (ESR)
Increase
Anode Foil
Capacitance Drop
Excessive
Operating Voltage
Leakage Current
Increase
Open Vent
Electrolyte Leakage
Deterioration of
Oxide Layer
Corrosion
Intermal Pressure Rise
Poor Sealing
Electrochemical Reaction
Capacitance
Drop
Less Electrolyte
Cathode Foil
Capacitance Drop
Unavoidable Factors
in Normal Service
Reverse Voltage
Excessive
Ripple Current
Contamination
by Chloride
Excessive
Charge-Discharge Duty
Chloride Contamination by Assembly Board Cleaning
Poor Sealing
11
CIRCUIT DESIGN
Environmental and Mounting Conditions
where Tc is the surface temperature (ºC) of capacitor case Tx is ditto.
Please make sure the environmental and mounting conditions are compliant
Kc is transfer coefficient between element and case of capacitor from
with their specifications in this catalog.
table below :
Operating Temperature, Equivalent Series Resistance(ESR), Ripple Current
Dia ≤8ø 10ø
and Load Life
Kc
12.5ø 13ø
1.10 1.15 1.20
16ø
18ø
22ø
25ø
30ø
35ø
1.20 1.25 1.30 1.35 1.40 1.50 1.65
MTTF(Mean-Time-To-Failure) means the useful life at room temperature 25ºC
1. Load Life (L0)
3. The Formula of Equivalent Series Resistance (ESR)
If the capacitor's max. operating temperature is at 105 ºC (85ºC), then
The operating frequency of ESR, DF, f & C must be the same, usually
after applying capacitor's rated voltage (WV) for L0 hours at 10ºC
are 120 Hz.
(85ºC), the capacitor shall meet the requirements in detail specification.
ESR = DF / 2πf C…………(2)
where L0 is called "load life" or "useful life (life time) at 105 ºC (85ºC)".
Where DF = Dissipation Factor (tanδ)
Lx = L0 x 2 (To-Tx) / 10 x K - ΔTx / 5
where ΔTx = ΔT0 x ( Ix / I0 )2
f = Operating Frequency (Hz)
C= Capacitance (F)
Ix > I0, K = 4; Ix ≤ I0, K = 2
4. Estimation of Life Considering the Ripple Current
2. Ripple Life (Lr)
The ripple current affects the life of a capacitor because the internal
If the capacitor's max. operating temperature is at 105 ºC (85ºC), then
loss (ESR) generates heat. The heat can be calculated by:
after applying capacitor's rated voltage (WV) with the ripple current for
P = I2 R------- (3)
Lr hours at 105 ºC (85ºC), the capacitor shall meet the requirements
Where I = Ripple current (Arms.)
in detail specification. where Lr is called "ripple life" or "useful ripple life
R= ESR (Ω)
(ripple lifetime) at 105 ºC (85ºC)".
Lx = Lr x 2 (To - Tx) / 10 x K (ΔTo - ΔTx) / 5
where ΔTx = ΔT0 x ( Ix / I0 )2
Ix > I0, K = 4; Ix ≤ I0, K = 2
5. Estimation of the Capacitor Temperature Increase
ΔT = I2R / AH------ (4)
Where ΔT= Temperature increase in the capacitor core (degree)
The (ripple) life expectancy at a lower temperature than the specified
I = Ripple current (Arms)
maximum temperature may be estimated by the following equation,
R= ESR (Ω)
but this expectancy formula does not apply for ambient below +40ºC.
A = Surface area of the capacitor (cm2)
L0 : Expected life period (hrs) at maximum operating temperature
H = Radiation coefficient (Approx.1.5~2.0´10-3 W / cm2)
allowed
Lr : Expected ripple life period (hrs) at maximum operating temperature
allowed
Lx : Expected life period (hrs) at actual operating temperature
The values of ΔT varies depending on the capacitor types and
operating conditions. The usage is generally desirable if ΔT remains less
than 5º. The measuring point for temperature increase due to ripple
current is shown below
T0 : Maximum operating temperature (ºC) allowed
Tx : Actual operating ambient temperature (ºC)
Ix : Actual applied ripple current (mA/rms) at operating frequency f0 (Hz)
Measuring Point
I0 : Rated maximum permissible ripple current IR (mA/rms) x frequency
multiplier (Cf) at f0 (Hz)
Ripple Current calculation: no need Temperature Multiplying Factor
Ix Should be 80% equal or more of I0
T0 : Maximum temperature rise (ºC) for applying I0 (mA/rms) = 5
Tc : Temperature rise (ºC) of capacitor case for applying Ix (mA/rms)
Tx : Temperature rise (ºC) of capacitor element for applying Ix (mA/
rms)= KcΔTc = Kc (Tc - Tx)
Fig.1-16
12
CIRCUIT DESIGN
Conditions of Use
Recommended Design Considerations
Aluminum Electrolytic Capacitors must not be used under the following
When designing a circuit board, please be noted to the following points:
conditions:
1. Make the hole spacing of the PC board match the lead space for the
1. When capacitors expose to high humidity or humidity condensation
capacitor.
situation such as water or saltwater spray, oil spray, steam.
2. There should not be any circuit pattern or circuit wire above the
2. When capacitors are exposed to toxic gases such as hydrogen sulfide,
capacitors.
sulfurous acid, nitrous acid, chlorine, ammonium... etc.
3. It is suggested to make a gas release hole when the capacitor's vent is
3. When capacitors are exposed to ozone, ultraviolet rays and radiation.
4. When severe vibration or shock occurs and exceeds the conditions
specified in the catalog or datasheet.
placed toward the PC board.
4. Do not install screw terminal capacitor upside down. When place a
screw terminal capacitor in a horizontal mount, the positive terminal
must be in the upper position.
5. Aluminum Electrolytic Capacitors should be electrically isolated from
the following circumstances
• Aluminum case, cathode lead wire, and anode lead wire.
5. Do not locate any wiring or circuit patterns directly above the
capacitor's vent.
• Auxiliary terminals of snap-in type, anode terminal, and outward terminal.
CAUTION FOR MOUNTING
Caution Before Assembly
4. Be careful not to deform the capacitor during installation.
1. When the capacitors that are removed from PC board for the
measuring electrical characteristics purpose at a periodical inspection,
can be recycled to the same position. However, when mounting and
5. The snap-in type of capacitors should be mounted firmly on the PC board
without a gap between the capacitor body and the surface of PC board.
applying electricity in unit, the capacitors cannot be recycled afterwards.
6. Avoid excessive force when clinching lead wire during auto-insertion process.
2. Aluminum Electrolytic Capacitors may accumulate charge during
storage. In this case, discharge through a 1KΩ resistor before use.
7. Avoid excessive shock to capacitors by automatic insertion machine,
during mounting, parts inspection or centering operations.
3. Leakage current of Aluminum Electrolytic Capacitors may be increased
during long storage time. In this case, the capacitors should be subjected
to voltage treatment through a 1KΩ resistor before use.
8. Please utilize supporting material such as strap or adhesive to mount
capacitors to PC board when it is anticipated that vibration or shock is applied.
In the Assembly Process
Soldering
1. Please confirm ratings before installing capacitors on the PC board.
1. All YAGEO's cp wires of electrolytic capacitors are lead free. (Pb).
2. Please confirm polarity before installing capacitors on the PC board.
2. Soldering conditions (temperatures, times) should be within the specified
conditions which are described in the catalog or specification sheets.
3. Do not make capacitors drop on the floor or use a dropped capacitor.
13
CAUTION FOR MOUNTING
3. If it is necessary that the leads must be formed due to a mismatch
Peak Temperature T°C
t sec (max)
of the lead space to hole space on the board, bend the lead prior to
250
4. If soldering capacitor has to be withdrawn from the PW board by
soldering iron, the capacitor should be removed after the solder has
melted completely in order to avoid stress to the capacitor or lead wires.
5. Soldering iron should never touch the capacitor's body.
Temperature at lead of capacitor (°C)
soldering without applying too much stress to the capacitor.
200
150
60 sec (max)
Preheat (160~190°C)
100
120 Sec (max)
90 sec (max)
50
Flow Soldering
Time (sec)
Fig. 1-18 Lead Free Type Reflow Soldering Condition
1. Do not dip capacitor's body into melted solder.
2. Din of flow soldering for the capacitors should be limited at 260ºC,
10 seconds.
SIZE
Temperature
t sec (max.)
ø4 ~ ø5 (4V ~ 50V)
250
10
260
5
250
5
3. Flux should not be adhered to capacitor's body but only to its terminals.
ø6.3 ~ ø10 (4V ~ 50V)
4. Other devices which are mounted near capacitors should not touch
the capacitors.
Cleaning
1. Satisfied characteristic of JIS C 5101.
Reflow Soldering Condition
1. For reflow, use a thermal condition system such as infrared radiation or
hot blast. Vapor heat transfer systems are not recommended.
2. Aluminum Electrolytic Capacitors may be damaged by corrosion that is
caused by any halogenated hydrocarbon solvents Ex: HCH(Cl)2). All of
2. Observe proper soldering conditions (i.e. temperature, time, etc.)
our products are non-solvent-proof, cleaning recommendation are as
followed.
Application: An type and rating
3. Do not exceed the specified limits.
Cleaning agents: pine Alpha ST-100S, Clean Through 750H/750L/710M,
Sanelek B-12, Aqua Cleaner 210SEP, Techno Care FRW14~17, Iso-
4. Repeated reflowing :
propyl Alcohol
* Avoid reflowing twice if possible.
* If repeated reflowing is unavoidable, contact Yageo after measuring the
first and the second reflow profiles and reflow interval at your side.
Peak Temperature 230°C
250
Cleaning conditions: Total cleaning time shall be within 5 minutes by
immersion, ultrasonic or other method. (Temperature of the cleaning
agent shall be 60ºC or lower). After cleaning, capacitors should be
dried using hot air for minimum of 10 minutes along with the PC board.
Temperature at lead of capacitor (°C)
20 sec (max)
200
Hot air temperature should be below the maximum operating temperature
of the capacitor. Insufficient drying after water rinse may cause appearance
150
100
60 sec (max)
problems, sleeve may shrink, or the bottom-plate may bulge, etc…
Preheat (140~180°C)
150 Sec (max)
100 sec (max)
50
Please inform Yageo in advance the solvent name and conditions for your PWB
Cleaning.
Time (sec)
Fig. 1-17 Reflow Soldering Condition
14
EMERGENCY ACTION
1. If you see smoke due to the operation of safety vent, turn off the main switch or pull out the plug.
2. Do not put your face near the safety vent as gas which is over 100ºC will be emitted when the safety vent operates. If the gas has entered your eyes, please rinse
your eyes immediately with water. If you breathe in the gas, immediately wash out your mouth and throat with water. Do not ingest electrolyte. If your skin is
exposed to electrolyte, please wash it immediately with soap and water.
STORAGE CONDITION
1. Aluminum electrolytic capacitors should not be stored in high temperatures or high level of humidity. The suitable storage condition is 5 ºC ~ 35 ºC and less than
75% in relative humidity.
2. Aluminum electrolytic capacitors should not be stored in damp conditions such as water, saltwater spray or oil spray.
3. Do not store aluminum electrolytic capacitors in an environment full of hazardous gases (hydrogen sulfide, sulfurous acid, nitrous acid, chlorine, ammonium, etc.)
4. Aluminum electrolytic capacitors should not be stored under exposure to ozone, ultraviolet rays or radiation.
5. If a capacitor has been stored more than a year under normal temperature (shorter time if higher temperature) and it shows increased leakage current, then a
treatment by voltage application is recommended.
ENVIRONMENT – RELATED SUBSTANCES
All YAGEO capacitors comply to RoHS requirements (Restriction of Hazardous Substances) where Chromium VI (Cr+6), Cadmium (Cd), Mercury (Hg), Lead (pb),
polybrominated biphenyls (PBBs) and Polybrominated bipheny1/dipheny1 ethers (PBBEs / PBDEs) have not detected (lower than MDL(Method Detection Limit))
per SGS certification test report.
DISPOSAL
Please dispose capacitors in either of the following ways:
1. Incinerate the capacitors after making a hole on the capacitor body.
2. A capacitor disposal specialist in burying procedure handling is recommended.
15
THE CHARACTERISITICS OF ENDURANCE TEST
Capacitance Change (%)
15.00
10.00
5.00
0.00
-5.00
-10.00
0
500
1000
1500
2000
Time (h)
0
500
1000
1500
2000
Time (h)
50.00
DF (%)
40.00
30.00
20.00
10.00
0.00
Leakage Current (µA)
8.00
6.00
4.00
2.00
A (100µF/25V)
0.00
-2.00
B (4.7µF/350V)
C (10µF/160V)
0
500
1000
1500
2000
Time (h)
16
MINIATURE & POLYMER ORDERING CODE
SK
063
M
0330
A
5
S
-
1019
Series Name
Case Size
2 Digits
4 Digits
0407= 04 x 07
0511= 05 x 11
1019= 10 x 19
1625= 16 x 25
1836= 18 x 36
2240= 22 x 40
Voltage
Capacitance
Rubber
3 Digits
006 = 6.3 V
010 = 10 V
063 = 63V
100 = 100 V
450 = 450 V
4 Digits
0R10= 0.1µF
1R00 =
1µF
0010 =
10µF
0330 =
330µF
1000 = 1000µF
10K0 = 10000µF
100K = 100000µF
1 Digit
F = Flat Rubber
S = Rubber Stand-off
Tolerance
Pitch
1 Digit
K =±10%
M =±20%
W =-5% ~ +20%
V =-10% ~ +20%
Others = Special design
1 Digit
1 = 1.5mm
2 = 2.0mm
3 = 3.5mm
5 = 5.0mm
7 = 7.5mm
H= 2.6mm
P =10.0mm
Z= 2.5mm
Package
1 Digit
A =Taping
B =Bulk
C =Lead Cut / Bulk
(Shape A)
D=Form & Crimp / Taping
F =Form & Lead Cut / Bulk
(Shape B)
K =Form & Lead Cut & Crimp / Bulk
(Shape C)
L =Lead Cut & Crimp / Bulk
(Shape D)
J =Lead Cut & Crimp / Bulk
(Shape E)
1 Digit
- = No Lead Cut / Standard
1 = Lead Cut Length 5.0 ± 0.2 mm
2 = Lead Cut Length 4.5 ± 0.2 mm
3 = Lead Cut Length 4.2 ± 0.2 mm
4 = Lead Cut Length 4.7 ± 0.2 mm
5 = Lead Cut Length 8.0 ± 0.2 mm
7 = Lead Cut Length15.0 ± 0.5 mm
8 = Lead Cut Length10.0 ± 0.2 mm
9 = Lead Cut Length 3.5 ± 0.3 mm
J = Lead Cut Length 3.1 ± 0.2 mm
L = Lead Cut Length 3.3 ± 0.2 mm
M = Lead Cut Length 3.7 ± 0.2 mm
Q= Lead Cut Length 7.0 ± 0.2 mm
V = Lead Cut Length 2.8 ± 0.2 mm
W= Lead Cut Length 4.0 ± 0.2 mm
17
LARGE CAN ORDERING CODE
LG
160
M
0820
B
P
F
-
2250
Series Name
Case Size
2 Digits
4 Digits
2250=22 x 50
2540=25 x 40
3030=30 x 30
3525=35 x 25
Voltage
Capacitance
Rubber & Terminal
3 Digits
006 = 6.3 V
010 = 10 V
160 = 160 V
450 = 450 V
4 Digits
0R10= 0.1µF
1R00 =
1µF
0010 =
10µF
0820 =
820µF
1000 = 1000µF
10K0 = 10000µF
100K = 100000µF
F = Flat Rubber & 2 pins
3 = Flat Rubber & 3 pins
4 = Flat Rubber & 4 pins
5 = Flat Rubber & 5 pins
Tolerance
Pitch
1 Digit
K =±10%
M =±20%
W =-5% ~ +20%
V =-10% ~ +20%
1 Digit
P =10.0mm
Package
1 Digit
B =Bulk
1 Digit
- =Terminal Length 5.8 ± 1.0 mm
4 =Terminal Length 4.0 ± 1.0 mm
18
SURFACE MOUNT ORDERING CODE
CA
063
M
0220
R
E
B
-
0405
Series Name
Size
2 Digits
4 Digits
0405=4.0 x 5.4
0505=5.0 x 5.4
0605=6.3 x 5.4
0607=6.3 x 7.7
0806=8.0 x 6.5
0810=8.0 x 10.5
1010=10.0 x 10.5
Voltage
Capacitance
Size
3 Digits
006 = 6.3 V
010 = 10 V
063 = 63 V
100 = 100 V
4 Digits
0R10= 0.1µF
1R00 =
1µF
0010 =
10µF
0220 =
220µF
1000 = 1000µF
1 Digit
B = 4.0 x 5.4
C = 5.0 x 5.4
D = 6.3 x 5.4
E = 8.0 x 6.5
F = 8.0 x 10.5
G = 10.0 x 10.5
H = 6.3 x 7.7
Tolerance
Life
1 Digit
K =±10%
M =±20%
W =-5% ~ +20%
V =-10% ~ +20%
1 Digit
S = 1000 Hours
E = 2000 Hours
Z= 3000 Hours
G= 5000 Hours
Package
1 Digit
R = Reel
19
SCREW TYPE ORDERING CODE
NP
350
M
10K0
32
076
146
Series Name
2 Digits
Voltage
Capacitance
Dimension
3 Digits
006 = 6.3 V
010 = 10 V
160 = 160 V
350 = 350 V
4 Digits
0R10= 0.1µF
1R00 =
1µF
0010 =
10µF
0820 =
820µF
1000 = 1000µF
10K0 = 10000µF
100K = 100000µF
3 Digits
051 = 51 mm
076 = 76 mm
089 = 89 mm
Tolerance
1 Digit
K =±10%
M =±20%
W =-5% ~ +20%
V =-10% ~ +20%
Pitch
Height
2 Digits
32 =32mm
3 Digits
050 = 50 mm
120 = 120 mm
146 = 146 mm
20
package information
RADIAL TYPE
D x L: mm
BULK
TAPING
LEAD CUTTING
BAG/PCS
INNER BOX
CARTON
INNER BOX
CARTON
BAG/PCS
INNER BOX
CARTON
04 x 05
1000
10,000
20,000
2,500
25,000
1000
15,000
30,000
05 x 05
1000
10,000
20,000
2,000
20,000
1000
15,000
30,000
06 x 05
1000
10,000
20,000
2,000
20,000
1000
15,000
30,000
04 x 07
1000
10,000
20,000
2,500
25,000
1000
15,000
30,000
05 x 07
1000
10,000
20,000
2,000
20,000
1000
15,000
30,000
06 x 07
1000
10,000
20,000
2,000
20,000
1000
15,000
30,000
05 x 11
500
10,000
20,000
2,000
20,000
500
15,000
30,000
06 x 11
500
10,000
20,000
2,000
20,000
500
15,000
30,000
08 x 11
500
6,000
12,000
1,000
10,000
500
8,000
16,000
08 x 15
500
5,000
10,000
1,000
10,000
500
5,000
10,000
08 x 20
200
4,000
8,000
1,000
10,000
200
4,000
8,000
10 x 12
200
4,000
8,000
700
7,000
200
4,000
8,000
10 x 15
200
3,000
6,000
700
7,000
200
4,000
8,000
10 x 16
200
3,000
6,000
700
7,000
200
4,000
8,000
10 x 19
200
2,400
4,800
700
7,000
200
3,000
6,000
10 x 25
200
2,400
4,800
700
7,000
200
2,400
4,800
10 x 27
200
2,000
4,000
200
2,000
4,000
10 x 30
200
2,000
4,000
200
2,000
4,000
12 x 20
200
2,000
4,000
500
5,000
200
2,000
4,000
12 x 25
200
1,800
3,600
500
5,000
200
1,800
3,600
12 x 30
200
1,200
2,400
200
1,600
3,200
12 x 35
200
1,000
2,000
500
3,000
12 x 40
200
1,000
2,000
500
3,000
13 x 20
200
1,800
3,600
500
5,000
200
1,800
3,600
13 x 25
200
1,400
2,800
500
5,000
200
1,400
2,800
13 x 30
200
1,200
2,400
500
3,000
13 x 40
200
1,000
2,000
500
3,000
16 x 25
200
1,000
2,000
500
4,000
16 x 32
200
1,000
1,600
500
3,000
16 x 36
200
600
1,200
500
3,000
16 x 40
200
600
1,200
500
3,000
18 x 20
200
800
1,600
1,000
2,000
18 x 25
200
800
1,600
500
2,000
18 x 32
100
500
1,000
500
2,000
18 x 36
100
500
1,000
500
2,000
18 x 40
100
300
1,000
500
2,000
22 x 40
100
300
600
400
800
300
3,000
200
SNAP-IN TYPE
INNER BOX
CARTON
SMD TYPE
REEL
CARTON
22 x 25 ~ 45
400
800
4x5
2,000
20,000
25 x 25 ~ 50
200
800
5x5
1,000
10,000
6x5
1,000
10,000
30 x 25 ~ 35
200
800
6x7
1,000
10,000
8x6
1,000
10,000
8 x 10
500
3,000
10 x 10
500
3,000
30 x 40 ~ 50
200
800
35 x 30 ~ 50
200
800
21
Diagram of Taping Dimensions
Unit: mm
Fig. 1
Fig. 4
P2
P2
P
P
1.0
1.0
P1
1.0Max.
F
A
D
A
D
P1
1.0Max.
F
H
H0
H
H0
W2
W1
L
W
W
t
t
W1
L
W2
W0
W0
D0
Mounting Tape
P0
D0
Mounting tape
P0
Adhesive Tape
d
Fig. 2
Adhesive tape
d
Fig. 5
P2
P
1.0
P
1.0
P2
D
A
P1
F
H
F
H
W2
W
W
t
t
W1
L
L
W2
W1
P1
A
D
W0
W0
D0
Mounting Tape
P0
P0
I
D0
Mounting Tape
Adhesive Tape
d
Adhesive Tape
d
Fig. 3
Fig. 6
P2
P
P2
P
1.0
P1
F
H
A
P1
D
A
D
1.0
H
F
I
P0
W
W
W0
t
W1
L
W2
t
W1
L
W2
W0
D0
Mounting Tape
d
Adhesive Tape
I
P0
D0
Mounting Tape
d
Adhesive Tape
22
Specifications Information
ITEM TOLERANCE ph = 2.5
L
5~7 ≤7
>7
straight lead type
L
L
5~7 ≤7
4ø
>7
5ø
≤7
>7
6ø
≤7
>7
5~7 ≤7
>7
5ø
≤7
8ø
4ø
13
8.0
22.0 8.0
13
8.0
0.5
0.5
0.5
0.5
0.5
>7
>7
12~25 15~25
+0.5, -0
4ø
A
Max.
8.0
13
8.0
13
8.0
d
±0.05
0.45
0.5
0.45
0.5
0.5
P
±1.0
12.7
12.7
12.7
15.0
P0
±0.3
12.7
12.7
12.7
15.0
P1
±0.7
5.1
3.85
5.6
P2
±1.3
6.35
6.35
6.35
F
+0.6, -0.2
2.5
5.0
1.5
W
+1.0, -0.5
18.0
18.0
18.0
W0
±0.5
12.0
12.0
12.0
W1
±0.5
9.0
9.0
9.0
W2
Max.
3.0
3.0
3.0
H
±0.75
18.5
18.5
18.5
H0
±0.5
16.0
16.0
-
I
Max.
-
-
-
D0
±0.2
4.0
4.0
4.0
t
±0.2
0.7
0.7
0.7
L
Max.
11.0
11.0
11.0
4
1
2
0.45
5.35
6ø
≤7
D
Fig.
5ø
Unit: mm
formed lead type
5.1
8ø
10ø
13
8.0
22.0 27.0
0.5
0.5
0.5
4.6
12ø
0.6
15~25
12.5ø 13ø 16ø 18ø
0.8
5.0
30.0
3.75
7.5
2.0
2.5
3.5
5.0
7.5 ± 0.8
1.0
3, 6
5
23
Diagram of lead Cutting and Forming
Shape (A)
Unit: mm
Shape (B)
Shape (C)
5ø, 6ø 1.12
8ø 1.32
E±0.1
d
F±0.5
F±0.5
H2±0.1
d
F±0.5
d
2.5 Max.
2.5 Max.
H±0.5
H±0.5
Shape (D)
H1±0.5
Shape (E)
10ø-13ø 1.32
16ø-22ø 1.50
E±0.1
d
d
F1±0.5
F±0.5
H2±0.5
2.5max
H2±0.1
F±0.5
H1±0.5
H1±0.5
Specifications Information
NO.
A
B
C
Unit: mm
CUTTING &
FORMING
METHODS
Dø 4ø
5ø
6ø
8ø
10ø
12ø
13ø
16ø
18ø
22ø
Lead Cut Only
F
1.5
2.0
2.5
3.5
5.0
5.0
5.0
7.5
7.5
10
H
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
d
0.45
0.5
0.5
0.5
0.6
0.6
0.6
0.8
0.8
0.8
F
5.0
5.0
5.0
5.0
H
5.0
5.0
5.0
5.0
d
0.45
0.5
0.5
0.5
Lead Cut,
F
5.0
5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0
Crimp and Form
H1 5.0 4.2 5.0 4.2 4.0 5.0 4.2 4.0 5.0 4.2 4.0
5.0
5.0
7.5
7.5
7.5
Lead Cut and Form
H2 2.5 2.0 2.5 2.0 2.0 2.5 2.0 2.0 2.5 2.0 2.0
d
D
E
Lead Cut and Crimp
Lead Cut Form and
Crimp
0.45
0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
F
5.0
5.0
H1
2.5
5.0 4.2 4.0 5.0 4.2 4.0 5.0 4.2 4.0 5.0 4.2 4.0 5.0 4.2 4.0 5.0 4.2 4.0
H2
3.5
2.5 2.0 2.0 2.5 2.0 2.0 2.5 2.0 2.0 2.5 2.0 2.0 2.5 2.0 2.0 2.5 2.0 2.0
d
0.5
0.6
F
5.0
5.0
5.0
5.0
F1 1.2
1.2
1.2
1.2
H1 4.0
4.0
4.0
4.0
H2 1.8
1.8
1.8
1.8
d
0.5
0.5
0.5
0.45
0.6
0.6
0.8
0.8
0.8
10
24
CARRIER TAPE DIMENSION
0.4±0.05
Unit: mm
ø1.5±0.1
4±0.1
1.75±0.1
B
t2±0.15
W±0.3
F
A
P1±0.1
CASE SIZE
(øD mm)
W
A
B
P1
F
t2
B
ø4
12.0
4.7
4.7
8.0
5.5
5.8
C
ø5
12.0
5.7
5.7
12.0
5.5
5.8
D
ø6.3 x 5.4
16.0
7.0
7.0
12.0
7.5
5.8
E
ø8 x 6.5
16.0
8.7
8.7
12.0
7.5
6.8
F
ø8 x 10.5
24.0
8.7
8.7
16.0
11.5
11.0
G
ø10 x 10.5
24.0
10.7
10.7
16.0
11.5
11.0
H
ø6.3 x 7.7
16.0
7.0
7.0
12.0
7.5
8.0
REEL DIMENSION
2±0.5
ø21± 0.8
80 ± 1
W2
380 ±2
380± 2
ø13± 0.5
SIZE CODE
B
C
D
E
F
G
H
W1±1
14
14
18
18
26
26
18
W2±1
20
20
24
24
32
32
24
W1
25
DETAILS OF CARRIER TAPE SPECIFICATION
(1) Details of carrier tape
Carrier tape
a. Last reeling empty part of carrier tape shall be more than
10 cm
b. Leader part of seal tape shall be more than 20 cm
Empty part
Seal tape
Adhesive tape
Lead part
Fixing tape
c. First reeling empty part of carrier tape shall be more than
10 cm
d. Adhesive tape fixing the end of the leader part shall be
Seal tape
approx 10 cm
(2) Deviation between carrier tape and seal tape
a. Deviation between carrier tape and seal tape shall be less
0.5 Max
Carrier tape
than 0.5 mm
b. Seal tape shall not cover on the feeding holes more than
Carrier tape
0.75 mm
0.75 Max
Seal tape
ADHESION TEST
Reasonable pulling strength: 0.1~0.7N, Pulling speed: 300mm / min
Reasonable pulling strength: 0.1~0.7N
Pulling speed: 300mm / min
Pull Scale
Seal tape
θ: apporx 10°
Carrier tape
θ
26
PACKING STYLE
(1) Carrier tape shall be reeled inside. (seal tape shall be outside)
(2) End of the tape shall be inside to the reel physically as shown in the
(1)
below figure and leader part of seal tape shall not be attached.
Reel
PACKAGING QUANTITY
SIZE CODE
DxL
ONE REEL (PCS)
TOTAL QUANTITY (PCS)
B
4 x 5.4
2,000
20,000
C
5 x 5.4
1,000
10,000
D
6.3 x 5.4
1,000
10,000
E
8 x 6.5
1,000
10,000
F
8 x 10.5
500
4,000
G
10 x 10.5
500
4,000
H
6.3 x 7.7
1,000
10,000
Yageo corporation ELECTROLYTIC CAPACITORS
S5 [ For Super Miniature ]
Miniature Aluminum
Electrolytic Capacitors
105°C Single-Ended Lead, 5.0mm Height Type Aluminum Electrolytic Capacitors
electrical characteristics
Operating Temperature Range : -40 ~ +105°C
Rated Voltage Range : 4 ~ 50V
Rated Capacitance Range : 0.1 ~ 470µF
Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C
DC Leakage Current (µA) : I = 0.01CV (µA) or 3µA whichever is greater.
(After Rated Voltage Applied for 2 Minutes )
description
Dissipation Factor : at 120 Hz, 20°C
W V (V): 4
6.3
10
D.F (%) : 35
24
20
The S5 series is smaller than SS series.
16
17
25
15
35
12
This type is designed for saving space and high density
insertion.
50
10
Endurance : After the rated voltage has been applied at 105°C for 1000 hours, the capacitors shall
meet following requirements.
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : 200% or Less of Initial Specified Value
(c) Leakage Current : Initial Specified Value or Less
Shelf Life : After leaving capacitors under load at 105°C for 500 hours.
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : 200% or Less of Initial Specified Value
(c) Leakage Current : 200% or Less of Initial Specified Value
Applications : Camera, Car Audio, Miniaudio and Other
Industrial and Commercial Applications
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz)
120 300 1K 10K~100K
0.1~47µF
1.00 1.20 1.30 1.50
100~330µF
1.00 1.10 1.15 1.20
Temperature Coefficient
TEMPERATURE (°C)
65
85
105
FACTOR
1.40
1.20
1.00
diagram of dimensions
Dimensions: mm
Rubber Stand-off
dø
4.0
1.5
0.45
5.0
2.0
6.3
2.5
8.0
3.5
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Vinyl Sleeve
(P.V.C)
Rubber End Seal
L
L ≤ 16 L + 1.5Max.
L > 16 L + 2Max.
Dø = 8 & 10 L + 2.5Max.
0.4Max.
15Min.
5Min.
F±0.5
F
F±0.5
Dø
D±0.5
Dø < 20 Dø + 0.5
Dø ≥ 20 Dø + 1
L
15Min.
5Min.
D±0.5
28
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
4 (5)
SIZE
6.3 (8)
RIPPLE SIZE
10 (13)
16 (20)
25 (32)
35 (44)
50 (63)
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE
0.10
4x5
1
0.22
4x5
2
0.33
4x5
3
0.47
4x5
4
1.0
4x5
9
2.2
4x5
13
3.3
4x5
17
4x5
17
5x5
20
4.7
4x5
10
4x5
18
4x5
20
4x5
20
23
15
22
33
47
4x5
4x5
5x5
20
25
30
4x5
4x5
28
33
4x5
35
5x5
45
68
100
6.3 x 5
50
5x5
55
6.3 x 5
70
220
6.3 x 5
70
6.3 x 5
90
330
8x5
110
8x5
115
8x5
100
470
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
5x5
33
4x5
29
5x5
37
4x5
16
4x5
20
5x5
27
6.3 x 5
42
4x5
34
5x5
44
5x5
45
5x5
41
6.3 x 5
49
6.3 x 5
53
5x5
46
5x5
54
5x5
55
6.3 x 5
58
6.3 x 5
65
6.3 x 5
85
8x5
90
6.3 x 5
54
6.3 x 5
80
4x5
18
5x5
30
6.3 x 5
33
6.3 x 5
48
6.3 x 5
55
Yageo corporation ELECTROLYTIC CAPACITORS
SS [ For Super Miniature ]
Miniature Aluminum
Electrolytic Capacitors
105°C Single-Ended Lead Aluminum Electrolytic Capacitors
electrical characteristics
Operating Temperature Range : -40 ~ +105°C
Rated Voltage Range : 4 ~ 63V
Rated Capacitance Range : 0.1 ~ 470µF
Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C
DC Leakage Current (µA) : I = 0.01CV (μA) or 3μA whichever is greater.
( After Rated Voltage Applied for 2 Minutes )
description
Dissipation Factor
W V (V): 4
D.F. (%) : 35
This type is designed to meet the demands of
equipments with greatly reduced size and thickness,
such as: portable micro computers, disk drivers, small
calculators and audio equipment.
6.3
24
10
20
16
17
25
15
35
12
50
10
63
8
Endurance : After the rated voltage has been applied at 105°C for 1000 hours
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : 200% or Less of Initial Specified Value
(c) Leakage Current : Initial Specified Value or Less
Applications : Portable Micro Computer, Disk Driver,
Small Calculator and Audio
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
Shelf Life : After leaving capacitors under load at 105°C for 500 hours.
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : 200% or Less of Initial Specified Value
(c) Leakage Current : 200% or Less of Initial Specified Value
FREQUENCY (Hz) 50
120 300 1K
10K
0.1~47µF
0.75 1.00 1.20 1.30 1.50
100~330µF
0.75 1.00 1.10 1.15 1.20
Temperature Coefficient
TEMPERATURE (°C)
65
85
105
FACTOR
1.70
1.30
1.00
diagram of dimensions
Dimensions: mm
Rubber Stand-off
dø
4.0
1.5
0.45
5.0
2.0
6.3
2.5
8.0
3.5
L
0.5
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
F±0.5
F
F±0.5
Dø
L ≤ 16 L + 1.5Max.
L > 16 L + 2Max.
Dø = 8 & 10 L + 2.5Max.
0.4Max.
15Min.
5Min.
D±0.5
Dø < 20 Dø + 0.5
Dø ≥ 20 Dø + 1
L
15Min.
5Min.
D±0.5
30
case size & permissible ripple current of standard products
CAP. (μF)
D x L: mm
Rated Voltage W V (SURGE VOLTAGE W V)
4 (5)
6.3 (8)
10 (13)
16 (20)
25 (32)
35 (44)
50 (63)
63 (79)
SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE SIZE RIPPLE
0.10
4x7
1
4x7
1
0.22
4x7
2
4x7
2
0.33
4x7
3
4x7
4
0.47
4x7
5
4x7
6
0.68
4x7
6
4x7
10
4x7
13
1.0
4x7
10
2.2
4x7
7
4x7
19
4x7
21
3.3
4x7
13
4x7
24
4x7
26
4.7
4x7
19
26
10
4x7
22
4x7
29
4x7
24
4x7
24
4x7
29
4x7
5x7
24
5x7
31
6.3 x 7 33
4x7
33
4x7
34
4x7
37
5x7
5x7
35
5x7
36
5x7
45
6.3 x 7 50
6.3 x 7 35
22
4x7
37
6.3 x 7 45
4x7
31
4x7
36
4x7
43
5x7
48
5x7
38
5x7
44
5x7
51
6.3 x 7 57
6.3 x 7 65
6.3 x 7 53
33
47
4x7
4x7
30
35
5x7
42
4x7
39
4x7
50
5x7
5x7
47
5x7
57
6.3 x 7 65
75
5x7
4x7
46
4x7
50
5x7
5x7
55
5x7
60
6.3 x 7 77
55
67
6.3 x 7 79
6.3 x 7 60
68
100
5x7
55
5x7
75
6.3 x 7 90
5x7
85
6.3 x 7 100
150
220
5x7
84
5x7
94
6.3 x 7 110
6.3 x 7 120
6.3 x 7 95
6.3 x 7 130
330
8x7
140
470
8x7
130
8x9
150
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
6.3 x 7 135
8x9
165
6.3 x 7 110
8x7
140
8x9
140
8x9
155
8x9
170
6.3 x 7 120
8x7
120
6.3 x 7 70
6.3 x 7 81
6.3 x 7 80
42
Yageo corporation ELECTROLYTIC CAPACITORS
SK [ For General ]
Miniature Aluminum
Electrolytic Capacitors
85°C Single-Ended Lead Aluminum Electrolytic Capacitors
Electrical Characteristics
Operating Temperature Range : -40 ~ +85°C / -25 ~ +85°C
Rated Voltage Range : 6.3 ~ 100V / 160 ~ 450V
Rated Capacitance Range : 0.1 ~ 22000µF / 0.47 ~ 470µF
Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C
description
DC Leakage Current (µA) : I = 0.01CV (μA) or 3μA / I = 0.03CV (μA) + 10μA whichever is greater.
(After Rated Voltage Applied for 2 Minutes )
Dissipation Factor
W V (V):
6.3 10
16
25
35
50
63
100 160 ~ 250
350 ~ 450
D.F (%) :
24
20
16
14
12
10
10
10
20
24
For capacitors whose capacitance exceeds 1000µF. The value of DF(%) is increased by 2% for every
addition of 1000µF.
Endurance : After the rated voltage has been applied at 85°C for 2000 hours, the capacitors shall
meet following requirements.
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : 200% or Less of Initial Specified Value
(c) Leakage Current : Initial Specified Value or Less
Shelf Life : After have been placed at 85°C without voltage applied for 1000 hours the capacitors shall
meet following requirements.
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : 200% or Less of Initial Specified Value
(c) Leakage Current : Initial Specified Value or Less
Lower-cost capacitors suitable for high density printed
circuit boards.
Very high volumetric efficiency
Ideally suited for general purpose applications,
decoupling bypass, and filtering circuit in entertainment
electronics.
Featuring high CV products with moderate cost
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz)
120 300 1K 10K~100K
6.3~100V Below~68µF
1.00 1.20 1.30 1.50
6.3~100V 100~680µF
1.00 1.10 1.15 1.20
6.3~110V 1000~22000µF 1.00 1.05 1.10 1.15
160~450V Below~220µF 1.00 1.25 1.40 1.40
160~450V 220µF Above
1.00 1.10 1.13 1.13
Temperature Coefficient
TEMPERATURE (°C)
50
70
85
FACTOR
1.30
1.15
1.00
diagram of dimensions
dø
0.45
0.5
Dimensions: mm
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
0.6
L
7.5
10.0
0.8
Rubber End Seal
Vinyl Sleeve
(P.V.C)
L ≤ 16 L + 1.5Max.
L > 16 L + 2Max.
Dø = 8 & 10 L + 2.5Max.
0.4Max.
15Min.
5Min.
F±0.5
F
1.5
2.0
2.5
3.5
5.0
F±0.5
Dø
4.0
5.0
6.3
8.0
10.0
12.0
13.0
16.0
18.0
22.0
D±0.5
Dø < 20 Dø + 0.5
Dø ≥ 20 Dø + 1
L
15Min.
5Min.
D±0.5
32
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
6.3 (8)
SIZE
10 (13)
16 (20)
25 (32)
35 (44)
50 (63)
63 (79)
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE
0.10
5 x 11
1
0.22
5 x 11
2
0.33
5 x 11
3
5 x 11
3
0.47
5 x 11
5
5 x 11
5
0.68
5 x 11
7
5 x 11
10
5 x 11
10
5 x 11
23
5 x 11
29
5 x 11
35
5 x 11
40
5 x 11
40
5 x 11
45
5 x 11
50
5 x 11
65
5 x 11
70
5 x 11
80
5 x 11
100
5 x 11
95
6.3 x 11
115
1.0
5 x 11
10
2.2
5 x 11
20
5 x 11
10
3.3
4.7
5 x 11
20
5 x 11
25
5 x 11
30
5 x 11
35
6.8
10
5 x 11
35
15
22
33
47
5 x 11
5 x 11
5 x 11
35
55
75
5 x 11
5 x 11
5 x 11
55
80
95
68
100
5 x 11
130
5 x 11
180
150
220
5 x 11
200
6.3 x 11 240
330
470
5 x 11
40
5 x 11
50
5 x 11
75
5 x 11
5 x 11
110
130
5 x 11
5 x 11
5 x 11
50
90
115
5 x 11
5 x 11
5 x 11
60
95
120
5 x 11
105
6.3 x 11
130
6.3 x 11
125
8 x 11
140
5 x 11
135
5 x 11
120
6.3 x 11
140
6.3 x 11
160
6.3 x 11
135
6.3 x 11
140
8 x 11
150
8 x 11
190
5 x 11
150
6.3 x 11
145
8 x 11
180
5 x 11
165
6.3 x 11
160
6.3 x 11
185
8 x 11
230
10 x 12
300
6.3 x 11
185
8 x 11
200
8 x 11
230
10 x 12
250
10 x 15
300
6.3 x 11
205
410
5 x 11
215
6.3 x 11
260
8 x 11
290
8 x 11
290
10 x 12
380
10 x 15
6.3 x 11
250
8 x 11
320
10 x 12
340
10 x 12
370
10 x 15
440
10 x 19.5 490
10 x 15
370
490
10 x 19.5 540
6.3 x 11 260
6.3 x 11
265
6.3 x 11
290
8 x 11
315
8 x 15
386
10 x 15
8 x 11
8 x 11
330
8 x 11
360
8 x 15
380
10 x 12
420
10 x 19.5 580
10 x 12
420
10 x 15
490
13 x 13
430
300
6.3 x 11 330
6.3 x 11
320
8 x 11
400
8 x 15
420
10 x 15
8 x 11
8 x 11
400
10 x 12
470
10 x 12
460
10 x 19.5 510
10 x 15
540
13 x 20
380
Note: 1. Ripple Current: (mA/rms) 85°C, 120Hz
640
13 x 20
680
10 x 19.5 610
13 x 20
755
13 x 20
13 x 25
880
16 x 25
880
530
760
33
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
680
1000
1200
6.3 (8)
SIZE
10 (13)
16 (20)
25 (32)
35 (44)
50 (63)
63 (79)
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE
8 x 11
410
3300
4700
6800
10000
15000
22000
10 x 12
460
10 x 12
510
10 x 15
540
13 x 20
705
13 x 25
965
10 x 15
565
10 x 19.5 595
13 x 25
780
16 x 25
1085
8 x 11
460
10 x 12
580
10 x 12
530
10 x 19.5 760
10 x 19.5 770
13 x 25
1100
16 x 25
1310
10 x 12
580
10 x 15
630
10 x 15
630
12 x 16
760
13 x 20
950
16 x 25
1350
16 x 32
1550
10 x 19.5 790
13 x 16
760
13 x 25
1100
13 x 20
950
16 x 25
1240
10 x 12
620
1500
2200
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
10 x 15
754
10 x 19.5 700
13 x 16
10 x 19.5 840
10 x 19.5 880
10 x 19.5 925
13 x 20
1100
16 x 25
1600
16 x 36
1850
18 x 40
2200
13 x 20
13 x 20
13 x 20
1100
13 x 25
1300
16 x 32
1800
18 x 36
2090
22 x 35
2200
13 x 25
1350
16 x 25
1550
22 x 40
2200
18 x 20
1550
22 x 40
2500
1050
1100
825
10 x 19.5 1000
13 x 20
1250
13 x 20
1200
16 x 25
1660
16 x 36
1970
18 x 36
2170
13 x 20
13 x 25
1400
13 x 25
1400
16 x 32
1950
18 x 36
2220
18 x 40
2400
16 x 25
1700
1250
13 x 20
1300
13 x 25
1500
13 x 40
1882
16 x 32
1950
16 x 36
2136
18 x 50
2350
13 x 25
1437
16 x 25
1800
16 x 25
1800
18 x 36
2360
18 x 36
2400
22 x 35
2240
16 x 25
1700
16 x 32
2100
22 x 40
2500
16 x 25
1900
16 x 25
1900
16 x 32
1980
16 x 32
2150
16 x 36
2200
18 x 36
2500
18 x 36
2700
22 x 40
2800
22 x 40
3200
16 x 25
1900
16 x 36
2225
16 x 32
2250
18 x 36
2500
16 x 36
2500
18 x 36
2950
22 x 40
3150
18 x 36
2880
18 x 40
3650
22 x 40
3700
22 x 40
3800
Note: 1. Ripple Current: (mA/rms) 85°C, 120Hz
18 x 36
2550
18 x 40
2200
22 x 40
2600
34
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
100 (125)
160 (200)
200 (250)
250 (300)
350 (400)
400 (450)
450 (500)
SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE
0.22
5 x 11
5
0.47
5 x 11
10
5 x 11
12
5 x 11
14
5 x 11
14
5 x 11
14
6.3 x 11
14
6.3 x 11
14
1.0
5 x 11
21
5 x 11
17
5 x 11
19
5 x 11
17
6.3 x 11
19
6.3 x 11
16
6.3 x 11
15
6.3 x 11
17
6.3 x 11
19
8 x 11
19
8 x 11
19
6.3 x 11
26
10 x 12
33
2.2
3.3
4.7
6.8
10
5 x 11
5 x 11
5 x 11
5 x 11
5 x 11
30
45
50
8 x 11
22
6.3 x 11
24
8 x 11
33
8 x 11
26
8 x 11
27
8 x 11
30
10 x 12
33
10 x 12
33
10 x 12
40
10 x 15
42
10 x 15
45
10 x 15
50
6.3 x 11
30
6.3 x 11
30
8 x 11
30
8 x 11
33
8 x 11
35
8 x 11
37
10 x 12
38
10 x 12
39
6.3 x 11
32
8 x 11
36
8 x 11
36
8 x 11
36
8 x 11
40
10 x 12
45
10 x 12
45
10 x 12
39
10 x 15
45
55
65
6.3 x 11 75
15
6.3 x 11
8 x 11
40
10 x 15
10 x 12
50
10 x 19.5 50
50
10 x 12
57
10 x 15
70
10 x 15
70
10 x 15
50
13 x 20
60
10 x 12
65
10 x 15
70
10 x 19.5 70
13 x 20
70
10 x 19.5 56
13 x 25
75
10 x 15
65
13 x 20
93
13 x 20
93
10 x 19.5 75
33
47
6.3 x 11 105
10 x 15
8 x 11
10 x 19.5 110
130
8 x 11
140
10 x 12
170
50
8 x 11
13 x 20
22
10 x 19.5 50
110
10 x 19.5 150
10 x 15
120
10 x 19.5 160
70
10 x 19.5 90
90
10 x 19.5 130
13 x 20
130
13 x 20
100
16 x 20
100
13 x 25
110
16 x 25
110
16 x 25
130
16 x 32
130
13 x 20
140
13 x 25
170
13 x 25
140
16 x 25
145
13 x 25
160
16 x 25
170
16 x 20
145
16 x 32
160
16 x 25
170
16 x 36
180
16 x 25
180
18 x 36
200
18 x 40
230
10 x 12
190
12 x 16
145
13 x 20
160
13 x 20
180
10 x 15
230
12 x 25
180
13 x 25
190
13 x 25
210
16 x 32
220
13 x 20
180
16 x 25
210
16 x 36
220
18 x 25
236
18 x 32
265
22 x 40
370
68
10 x 15
280
100
10 x 19.5 400
13 x 25
250
16 x 25
300
Note: 1. Ripple Current: (mA/rms) 85°C, 120Hz
13 x 25
230
16 x 25
330
16 x 32
310
16 x 25
220
16 x 36
320
16 x 36
320
18 x 36
360
18 x 36
360
35
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
100 (125)
160 (200)
200 (250)
250 (300)
350 (400)
400 (450)
450 (500)
SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE
150
13 x 20
500
220
13 x 25
710
330
470
18 x 25
485
18 x 36
540
16 x 36
510
18 x 32
540
18 x 40
600
18 x 36
600
18 x 36
540
16 x 40
710
16 x 25
860
18 x 40
600
16 x 45
750
18 x 32
685
18 x 36
725
18 x 40
800
18 x 40
750
22 x 35
1000
16 x 25
1100
16 x 32
1100
680
16 x 36
1260
1000
18 x 40
1350
22 x 35
1680
22 x 40
2300
2200
450
720
1100
410
16 x 32
13 x 25
13 x 40
18 x 40
22 x 40
Note: 1. Ripple Current: (mA/rms) 85°C, 120Hz
900
18 x 40
800
Yageo corporation ELECTROLYTIC CAPACITORS
Miniature Aluminum
Electrolytic Capacitors
SE-K [ For General ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors Rated Voltage up to 450V
electrical characteristics
Operating Temperature Range : -40 ~ +105°C / -40 ~ +105°C / 25 ~ +105°C
Rated Voltage Range : 6.3 ~ 100V / 160 ~ 250V / 350 ~ 450V
Rated Capacitance Range : 0.47 ~ 15000μF / 0.47 ~ 470μF / 0.47 ~ 150μF
Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C
description
Leakage Current (µA) : I = 0.01CV (μA) + 3μA / 0.03CV (μA) + 10μA whichever is greater.
(After Rated Voltage Applied for 2 Minutes)
Lower-cost capacitors suitable for high density printed
circuit boards.
Dissipation Factor
W V (V): 6.3
D.F. (%) : 26
Very high volumetric efficiency
Ideally suited for general purpose applications, coupling,
decoupling, bypass, and filtering circuit in entertainment
electronics.
Featuring high CV products with moderate cost
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz)
120 300 1K 10K~100K
6.3~100V Below~68µF
1.00 1.20 1.30 1.45
6.3~100V 100~680µF
1.00 1.10 1.15 1.25
10
22
16
18
25
16
35
14
50
12
63~100
10
160 ~ 250
15
350 ~ 450
20
Endurance : After the rated voltage has been applied at 105°C for 1000 hours. The capacitors shall
meet the following requirements.
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : 200% or Less of Initial Specified Value
(c) Leakage Current : Initial Specified Value or Less
Shelf Life : After leaving capacitors under no load at 105°C for 500 hours, the capacitors shall meet
the same requirements as Endurance.
6.3~110V 1000~22000µF 1.00 1.05 1.10 1.15
160~450V ALL Cap(µF)
1.00 1.05 1.10 1.50
diagram of dimensions
Dimensions: mm
Rubber Stand-off
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Dø
F
dø
5.0
2.0
0.5
6.3
2.5
F±0.5
F±0.5
8.0
3.5
10.0
5.0
0.6
12.0
L
15Min.
5Min.
D±0.5
L
L ≤ 16 L + 1.5Max.
l > 16 L + 2Max.
Dø = 8 & 10 L + 2.5Max.
0.4Max.
15Min.
5Min.
D±0.5
Dø < 20 Dø + 0.5
Dø ≥ 20 Dø + 1
13.0
16.0
7.5
0.8
10.0
0.8 (1.0)
18.0
22.0
37
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
6.3 (8)
SIZE
10 (13)
16 (20)
25 (32)
35 (44)
50 (63)
63 (79)
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE
0.47
5 x 11
7
5 x 11
8
0.68
5 x 11
7
1.0
5 x 11
12
5 x 11
13
2.2
5 x 11
18
5 x 11
20
3.3
5 x 11
25
5 x 11
27
4.7
5 x 11
20
5 x 11
25
5 x 11
30
5 x 11
34
6.8
5 x 11
25
5 x 11
30
5 x 11
32
5 x 11
37
10
5 x 11
25
5 x 11
30
5 x 11
40
5 x 11
50
5 x 11
55
15
5 x 11
40
5 x 11
45
5 x 11
50
5 x 11
60
5 x 11
65
5 x 11
55
5 x 11
60
5 x 11
65
5 x 11
75
5 x 11
75
6.3 x 11
90
6.3 x 11
110
8 x 11
120
22
5 x 11
33
47
5 x 11
5 x 11
60
5 x 11
45
60
75
5 x 11
70
5 x 11
85
6.3 x 11
97
5 x 11
5 x 11
75
90
5 x 11
85
6.3 x 11
105
5 x 11
95
6.3 x 11
105
6.3 x 11
128
6.3 x 11
115
8 x 11
125
8 x 11
155
68
5 x 11
75
5 x 11
80
5 x 11
100
6.3 x 11
125
8 x 11
130
8 x 11
159
10 x 12
198
100
5 x 11
100
5 x 11
110
5 x 11
110
6.3 x 11
145
6.3 x 11
150
8 x 11
160
8 x 15
230
6.3 x 11
135
6.3 x 11
135
8 x 11
160
8 x 11
190
10 x 12
210
10 x 12
260
5 x 11
110
8 x 11
180
8 x 11
200
10 x 12
240
10 x 12
289
10 x 15
330
6.3 x 11
130
5 x 11
150
6.3 x 11
180
8 x 11
200
8 x 11
230
10 x 12
340
10 x 15
400
6.3 x 11
180
8 x 11
235
10 x 12
250
8 x 15
280
10 x 15
400
10 x 19.5 460
10 x 12
315
450
10 x 19.5 520
150
220
5 x 11
5 x 11
120
140
6.3 x 11 165
270
330
470
8 x 11
210
6.3 x 11 160
6.3 x 11
205
8 x 11
8 x 11
255
200
8 x 11
285
8 x 11
265
8 x 15
345
10 x 15
8 x 15
320
8 x 20
420
10 x 19.5 535
13 x 20
650
10 x 12
355
10 x 12
380
10 x 15
440
415
10 x 19.5 580
13 x 20
700
13 x 20
13 x 25
800
6.3 x 11 220
6.3 x 11
245
8 x 11
310
8 x 15
365
10 x 15
8 x 11
8 x 11
305
8 x 15
360
10 x 12
400
10 x 19.5 490
10 x 12
395
10 x 15
470
13 x 20
580
10 x 30
600
280
560
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
730
38
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
680
1000
1500
2200
3300
4700
6800
10000
15000
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
6.3 (8)
SIZE
10 (13)
16 (20)
25 (32)
35 (44)
50 (63)
63 (79)
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE
8 x 11
255
8 x 11
335
10 x 12
455
10 x 15
10 x 12
320
8 x 15
385
10 x 15
530
10 x 19.5 650
13 x 20
730
10 x 12
420
540
10 x 19.5 600
13 x 25
860
13 x 25
840
16 x 25
1000
8 x 11
370
8 x 11
390
8 x 20
600
10 x 19.5 680
13 x 20
850
13 x 25
930
16 x 25
1020
10 x 12
470
8 x 15
450
10 x 15
590
13 x 20
855
13 x 25
995
16 x 25
1110
16 x 32
1200
10 x 12
490
10 x 19.5 700
10 x 15
570
13 x 25
1020
13 x 25
935
16 x 32
1350
16 x 32
1300
16 x 25
1110
16 x 36
1450
18 x 36
1455
10 x 15
600
10 x 19.5 750
10 x 19.5 680
13 x 20
860
10 x 19.5 740
10 x 19.5 800
10 x 25
895
13 x 25
1030
16 x 25
1230
16 x 36
1360
13 x 20
13 x 20
12 x 25
1040
16 x 25
1230
16 x 32
1450
18 x 36
1530
13 x 20
990
13 x 25
1150
930
1010
10 x 19.5 880
10 x 25
950
13 x 25
1140
13 x 25
1035
16 x 36
1470
18 x 36
1540
13 x 20
10 x 30
1090
16 x 25
1350
16 x 25
1230
18 x 36
1660
18 x 40
1700
13 x 20
1050
16 x 32
1450
13 x 25
1220
22 x 35
1900
1100
13 x 25
1100
13 x 25
1190
16 x 25
1330
16 x 32
1420
18 x 36
1580
16 x 25
1320
16 x 25
1410
16 x 32
1560
18 x 36
1690
18 x 40
1750
13 x 25
1250
16 x 25
1370
16 x 32
1400
18 x 36
1850
18 x 40
1600
16 x 25
1490
16 x 32
1610
16 x 36
1590
22 x 40
1885
16 x 40
1670
18 x 32
1600
18 x 36
1790
18 x 36
2100
16 x 25
1560
16 x 36
1760
16 x 32
1830
18 x 36
1980
18 x 36
2280
18 x 40
1960
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
39
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
100 (125)
160 (200)
200 (250)
250 (300)
350 (400)
400 (450)
450 (500)
SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE
0.47
5 x 11
10
5 x 11
12
5 x 11
14
5 x 11
14
5 x 11
14
6.3 x 11
14
6.3 x 11
14
1.0
5 x 11
15
5 x 11
17
5 x 11
19
6.3 x 11
19
6.3 x 11
20
6.3 x 11
16
8 x 11
20
8 x 11
20
8 x 11
28
10 x 12
35
10 x 12
35
10 x 15
54
10 x 15
60
2.2
3.3
4.7
6.8
10
5 x 11
5 x 11
5 x 11
5 x 11
5 x 11
22
29
37
46
55
6.3 x 11 65
15
22
33
47
8 x 11
8 x 11
82
115
8 x 11
120
10 x 12
160
10 x 12
180
10 x 15
210
6.3 x 11
25
6.3 x 11
22
6.3 x 11
23
8 x 11
28
8 x 11
29
8 x 11
35
6.3 x 11
30
6.3 x 11
32
8 x 11
33
8 x 11
37
8 x 11
38
8 x 11
36
8 x 11
40
10 x 12
42
10 x 12
47
10 x 12
50
6.3 x 11
34
8 x 11
40
8 x 11
41
8 x 11
37
8 x 11
40
8 x 11
43
10 x 12
50
10 x 12
52
10 x 12
47
8 x 15
45
10 x 15
55
10 x 12
49
10 x 15
57
10 x 15
60
10 x 12
54
10 x 12
60
8 x 15
57
10 x 12
62
88
8 x 11
56
10 x 12
69
10 x 15
10 x 12
70
10 x 15
80
10 x 19.5 90
10 x 15
90
8 x 20
125
10 x 15
130
10 x 19.5 180
13 x 20
270
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
10 x 15
10 x 15
110
140
10 x 19.5 190
13 x 20
240
13 x 25
290
10 x 15
120
10 x 19.5 155
13 x 20
170
13 x 25
200
13 x 25
330
10 x 15
65
10 x 19.5 70
10 x 19.5 72
10 x 15
95
10 x 19.5 140
13 x 20
13 x 25
16 x 25
165
220
340
10 x 15
65
10 x 19.5 75
10 x 19.5 77
13 x 20
85
13 x 20
13 x 25
100
16 x 25
160
97
10 x 19.5 100
13 x 20
125
13 x 25
150
13 x 20
150
13 x 25
125
13 x 25
175
16 x 25
150
16 x 32
180
13 x 25
190
16 x 25
190
16 x 20
195
16 x 36
240
16 x 25
230
16 x 25
280
16 x 36
300
16 x 32
315
18 x 40
360
16 x 36
350
18 x 20
275
18 x 25
300
40
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
100 (125)
160 (200)
200 (250)
250 (300)
350 (400)
400 (450)
450 (500)
SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE SIZE
RIPPLE
68
100
10 x 15
241
10 x 19.5 385
13 x 25
300
13 x 25
330
13 x 25
330
13 x 25
340
16 x 25
400
16 x 25
410
16 x 25
16 x 32
350
430
16 x 32
18 x 36
370
460
120
150
13 x 25
414
16 x 32
435
16 x 32
400
16 x 36
450
18 x 40
460
180
220
330
470
13 x 25
590
16 x 32
550
18 x 32
520
16 x 36
620
18 x 36
580
18 x 40
650
13 x 25
600
18 x 36
770
18 x 36
705
16 x 25
720
18 x 40
850
18 x 40
780
22 x 40
920
16 x 25
740
16 x 32
875
680
16 x 36
1200
1000
18 x 40
1340
22 x 40
1500
22 x 40
980
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
22 x 40
680
22 x 40
480
16 x 32
320
18 x 32
305
16 x 36
335
22 x 40
400
18 x 25
305
18 x 36
380
16 x 36
425
18 x 36
380
18 x 32
430
18 x 40
400
18 x 36
480
22 x 40
450
18 x 36
480
22 x 40
450
18 x 40
350
Yageo corporation ELECTROLYTIC CAPACITORS
SH [ For General ]
Miniature Aluminum
Electrolytic Capacitors
105°C Single-Ended Lead Aluminum Electrolytic Capacitors
for the Rated Voltage up to 450V
electrical characteristics
Operating Temperature Range : -40 ~ +105°C / -25 ~ +105°C
Rated Voltage Range : 6.3 ~ 100V / 160 ~ 450V
Rated Capacitance Range : 0.47 ~ 15000µF / 0.47 ~ 470μF
Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C
Leakage Current (µA) : I = 0.01CV (μA) + 3μA / 0.03CV (μA) + 10μA
(After Rated Voltage Applied for 2 Minutes )
description
Dissipation Factor
W V (V) : 6.3
10
16
25
35
50
63 ~ 100
160 ~ 250
350 ~ 450
D.F (%) : 26
22
18
16
14
12
10
15
20
For capacitors whose capacitance exceeds 1000µF. The value of DF(%) is increased by 2% for every
addition of 1000µF.
Long life for 2000 hours at 105°C, ideally suited for
high quality and high reliability applications.
Low Temperature Stability Impedance Ratio (Max.)
W V (V)
:
6.3 10
Impedance : Z - 25°C / Z + 25°C
4
3
Z - 40°C / Z + 20°C
8
6
16
2
4
25 ~ 100
2
3
160 ~ 250
4
-
350 ~ 450
4
-
Endurance : After the rated voltage has been applied at 105°C for 2000 hours, the capacitors shall
meet following requirements.
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : 200% or Less of Initial Specified Value
(c) Leakage Current : Initial Specified Value or Less
Featuring high CV products
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz)
120 300 1K 10K~100K
6.3~100V Below~68µF
1.00 1.30 1.57 2.00
6.3~100V 100~470µF
1.00 1.23 1.34 1.50
6.3~100V 471~22000µF
1.00 1.10 1.13 1.15
160~450V ALL Cap(µF)
1.00 1.25 1.40 1.60
Temperature Coefficient
TEMPERATURE (°C)
65
85
105
FACTOR
1.70
1.40
1.00
Shelf Life: After leaving capacitors under no load at 105°C for 1000 hours, the capacitors shall meet
the same requirements as Endurance.
diagram of dimensions
Dø
F
dø
5.0
2.0
0.5
6.3
2.5
8.0
3.5
10.0
5.0
0.6
Dimensions: mm
Rubber Stand-off
Coated case
13.0
L+a
7.5
18.0
22.0
10.0
15Min.
4Min.
F±0.5
P±0.5
12.0
16.0
Rubber End Seal
Vinyl Sleeve
(P.V.C)
D±0.5
0.8
L ≤ 16 L + 1.5Max.
L > 16 L + 2Max.
Dø = 8 & 10 L + 2.5Max.
Dø < 20 Dø + 0.5
Dø ≥ 20 Dø + 1
L
15Min.
5Min.
D±0.5
42
case size & permissible ripple current of standard products
CAP. (μF)
D x L: mm
Rated Voltage W V (SURGE VOLTAGE W V)
6.3 (8)
SIZE
RIPPLE
10 (13)
SIZE
RIPPLE
10
16 (20)
SIZE
RIPPLE
25 (32)
SIZE
RIPPLE
35 (44)
SIZE
RIPPLE
5 x 11
44
5 x 11
43
5 x 11
44
5 x 11
50
15
22
33
5 x 11
60
5 x 11
65
5 x 11
70
5 x 11
75
5 x 11
85
47
5 x 11
75
5 x 11
85
5 x 11
90
6.3 x 11
115
68
5 x 11
80
5 x 11
100
6.3 x 11
125
8 x 11
130
5 x 11
110
5 x 11
115
6.3 x 11
145
6.3 x 11
150
6.3 x 11
135
8 x 11
190
100
5 x 11
100
150
5 x 11
120
6.3 x 11
130
8 x 11
180
8 x 11
200
10 x 12
240
220
6.3 x 11
165
6.3 x 11
180
6.3 x 11
180
8 x 11
200
10 x 12
315
8 x 11
235
10 x 12
250
8 x 11
315
10 x 12
355
10 x 12
380
10 x 12
285
10 x 15
440
8 x 11
315
10 x 15
440
10 x 12
395
10 x 19.5
460
13 x 20
580
330
470
6.3 x 11
161
8 x 11
200
6.3 x 11
225
8 x 11
280
8 x 11
8 x 11
255
305
10 x 15
470
680
10 x 12
320
10 x 12
420
10 x 15
530
10 x 19.5
650
13 x 20
730
1000
10 x 12
470
10 x 12
490
10 x 19.5
700
13 x 20
855
13 x 25
995
10 x 15
570
10 x 19.5
750
10 x 19.5
705
13 x 25
1020
16 x 25
1110
13 x 20
860
16 x 25
1230
16 x 25
1236
16 x 32
1450
16 x 36
1477
18 x 36
1660
1500
2200
3300
4700
10 x 15
13 x 20
13 x 20
16 x 25
600
930
1100
1320
10 x 19.5
800
13 x 20
991
13 x 20
1010
13 x 25
1150
13 x 25
1220
13 x 25
1150
16 x 25
1350
16 x 25
1330
16 x 32
1560
18 x 36
1790
16 x 25
1410
6800
16 x 25
1490
16 x 32
1610
10000
16 x 32
1830
18 x 36
1980
15000
18 x 36
2280
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
16 x 32
18 x 36
1450
1690
43
case size & permissible ripple current of standard products
CAP. (μF)
D x L: mm
Rated Voltage W V (SURGE VOLTAGE W V)
50 (63)
SIZE
RIPPLE
63 (79)
SIZE
RIPPLE
100 (125)
SIZE
RIPPLE
160 (200)
SIZE
RIPPLE
200 (250)
SIZE
RIPPLE
0.47
5 x 11
7
5 x 11
8
5 x 11
10
5 x 11
12
5 x 11
12
1.0
5 x 11
12
5 x 11
12
5 x 11
15
5 x 11
17
6.3 x 11
17
2.2
5 x 11
18
5 x 11
20
5 x 11
22
6.3 x 11
25
6.3 x 11
25
3.3
5 x 11
25
5 x 11
27
5 x 11
29
8 x 11
36
8 x 11
36
4.7
5 x 11
30
5 x 11
34
5 x 11
37
6.3 x 11
34
10 x 12
50
8 x 11
43
6.8
5 x 11
30
5 x 11
37
5 x 11
46
10 x 12
54
10 x 12
60
10
5 x 11
50
5 x 11
55
6.3 x 11
65
10 x 12
70
10 x 12
69
10 x 15
80
15
5 x 11
50
5 x 11
65
8 x 11
82
10 x 15
90
10 x 19.5
110
22
5 x 11
75
6.3 x 11
90
8 x 11
115
10 x 19.5
130
10 x 15
140
10 x 19.5
150
13 x 20
220
13 x 25
190
13 x 20
220
13 x 25
260
16 x 20
242
16 x 25
280
33
47
68
100
6.3 x 11
105
6.3 x 11
101
8 x 11
125
8 x 11
159
8 x 11
169
8 x 11
8 x 11
10 x 12
110
155
198
10 x 12
260
10 x 12
10 x 15
10 x 19.5
160
210
241
10 x 19.5
305
13 x 20
13 x 25
13 x 25
180
250
270
16 x 25
390
16 x 32
400
10 x 12
210
13 x 20
385
150
10 x 12
289
10 x 15
330
13 x 25
414
16 x 32
435
16 x 36
450
220
10 x 12
346
10 x 19.5
465
13 x 25
495
16 x 36
700
18 x 36
675
10 x 15
400
16 x 25
590
18 x 40
750
10 x 19.5
535
16 x 25
720
18 x 40
780
13 x 20
600
22 x 40
920
10 x 19.5
560
13 x 20
650
18 x 45
800
13 x 20
730
13 x 25
800
22 x 40
920
680
13 x 25
860
16 x 25
1000
1000
16 x 25
1110
330
470
13 x 20
650
16 x 25
1023
16 x 32
1200
1500
16 x 32
1350
16 x 36
1450
2200
16 x 36
1360
18 x 45
1800
18 x 36
1530
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
16 x 32
16 x 36
875
1200
18 x 40
22 x 40
850
980
44
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
Rated Voltage W V (SURGE VOLTAGE W V)
250 (300)
SIZE
RIPPLE
350 (400)
SIZE
RIPPLE
400 (450)
SIZE
RIPPLE
450 (500)
SIZE
RIPPLE
0.47
5 x 11
12
6.3 x 11
14
6.3 x 11
14
6.3 x 11
16
1.0
6.3 x 11
17
6.3 x 11
15
6.3 x 11
17
8 x 11
22
8 x 11
20
8 x 11
20
10 x 12
35
8 x 11
29
10 x 12
37
10 x 12
35
10 x 12
42
10 x 12
42
10 x 15
49
10 x 15
51
10 x 15
59
2.2
3.3
4.7
6.3 x 11
23
8 x 11
29
8 x 11
34
10 x 12
42
8 x 11
41
10 x 12
43
10 x 12
66
10 x 12
52
10 x 15
55
10 x 15
57
10 x 15
47
6.8
10 x 12
62
10 x 19.5
65
10 x 15
67
13 x 20
69
10
10 x 15
75
10 x 15
65
10 x 19.5
75
10 x 19.5
72
10 x 19.5
88
13 x 20
95
13 x 20
97
13 x 25
99
15
13 x 20
120
13 x 20
140
13 x 25
145
16 x 25
150
22
13 x 20
130
13 x 20
125
13 x 20
120
16 x 25
145
13 x 25
155
16 x 25
165
13 x 25
140
16 x 32
175
16 x 20
147
16 x 25
170
33
47
68
100
13 x 25
200
16 x 20
150
16 x 20
164
16 x 32
211
16 x 32
195
16 x 25
190
18 x 36
250
18 x 40
350
18 x 16
148
16 x 32
230
13 x 25
228
16 x 36
210
16 x 25
200
16 x 25
270
18 x 36
240
16 x 32
250
18 x 25
243
18 x 36
300
18 x 25
310
18 x 32
320
18 x 36
325
22 x 40
380
18 x 45
420
16 x 32
300
18 x 36
320
16 x 36
300
18 x 40
300
18 x 32
280
18 x 36
440
22 x 40
360
18 x 36
290
22 x 40
365
18 x 32
300
18 x 36
320
18 x 40
350
22 x 40
465
120
150
18 x 40
600
220
22 x 40
800
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
22 x 40
480
Yageo corporation ELECTROLYTIC CAPACITORS
SG [ Electronic Ballast ]
Miniature Aluminum
Electrolytic Capacitors
105°C Single-Ended Lead Aluminum Electrolytic Capacitors
Electrical Characteristics
Operating Temperature Range : -40 ~ +105°C / -25 ~ +105°C
Rated Voltage Range : 160 ~ 400V / 450V
Rated Capacitance Range : 4.7 ~ 330µF / 3.3~100µF
Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C
DC Leakage Current (μA): I = 0.06CV (μA) + 10μA whichever is greater.
(After Rated Voltage Applied for 2 Minutes)
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
Dissipation Factor
WV (V) : 160
D.F. (%) : 15
FREQUENCY (Hz)
200
15
250
15
350
20
400
24
450
24
50
60
120
300
6.3~100V Below~68μF 0.8
0.8
1.0
1.2
FREQUENCY (Hz)
10K~100K
1K
6.3~100V Below~68μF 1.4
Low Temperature Stability Impedance Ratio (Max.)
W V (V) :
160
200
250
350
Z - 25°C / Z + 20°C
3
3
3
5
Z - 40°C / Z + 20°C
6
6
6
6
400
5
6
1.6
450
6
-
Endurance : After the rated voltage and rated ripple current have been applied at 105°Cfor 5000
hours, the capacitors shall meet the following requirements.
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : 200% or Less of Initial Specified Value
(c) Leakage Current : Initial Specified Value or Less
Shelf Life : After having been placed at 105°C without voltage applied for 1000 hours, the capacitors
shall meet the same requirements as Endurance.
diagram of dimensions
Dø
F
dø
5.0
2.0
0.5
6.3
2.5
8.0
3.5
10.0
5.0
0.6
Dimensions: mm
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
13.0
7.5
0.8
18.0
22.0
10.0
0.8 (1.0)
L
L ≤ 16 L + 1.5Max.
L > 16 L + 2Max.
Dø = 8 & 10 L + 2.5Max.
15Min.
5Min.
F±0.5
F±0.5
12.0
16.0
Rubber End Seal
Vinyl Sleeve
(P.V.C)
D±0.5
Dø < 20 : Dø+0.5
Dø ≥ 20 : Dø+1
L
15Min.
5Min.
D±0.5
46
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
160 (200)
SIZE
RIPPLE
10
15
22
33
47
68
100
150
220
330
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
10 x 19.5
10 x 19.5
13 x 20
160
210
260
200 (250)
SIZE
RIPPLE
250 (300)
SIZE
RIPPLE
*10 x 15
80
*10 x 15
85
*10 x 19.5
100
*10 x 25
145
13 x 20
160
13 x 20
210
13 x 25
270
16 x 20
275
*10 x 15
100
10 x 19.5
160
*10 x 19.5
160
13 x 20
210
13 x 20
260
13 x 25
360
13 x 25
360
16 x 25
380
16 x 20
430
16 x 20
430
18 x 20
375
16 x 25
475
16 x 25
475
16 x 32
520
18 x 20
465
18 x 20
465
18 x 25
500
16 x 32
650
18 x 25
650
18 x 32
650
18 x 25
625
16 x 32
750
18 x 32
780
18 x 40
820
18 x 25
725
18 x 32
960
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
2. *Down size: 3000 Hours
47
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
350 (400)
SIZE
RIPPLE
400 (450)
SIZE
RIPPLE
3.3
450 (500)
SIZE
RIPPLE
10 x 19.5
60
4.7
*10 x 15
60
13 x 20
80
6.8
*10 x 15
72
*10 x 19.5
90
10 x 19.5
100
13 x 20
110
13 x 25
110
10
22
33
47
68
100
10 x 19.5
13 x 20
100
160
13 x 25
170
16 x 25
190
16 x 20
200
18 x 20
200
13 x 25
230
16 x 25
230
16 x 32
275
16 x 20
250
18 x 20
250
18 x 25
280
16 x 25
300
16 x 32
300
18 x 32
340
18 x 20
315
18 x 25
325
16 x 32
400
18 x 36
420
18 x 32
395
18 x 25
380
18 x 40
460
18 x 32
530
22 x 40
580
150
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
2. *Down size: 3000 Hours
18 x 40
545
22 x 40
650
Yageo corporation ELECTROLYTIC CAPACITORS
Miniature Aluminum
Electrolytic Capacitors
SP [ Miniature and Long Life ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors For Electronic Ballast
Electrical Characteristics
Operating Temperature Range : -40 ~ +105°C / -25 ~ +105°C
Rated Voltage Range : 160 ~ 400V / 450V
Rated Capacitance Range : 3.3 ~ 330µF
Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C
description
DC Leakage Current (μA) : I = 0.04CV (μA) + 100μA whichever is greater.
(After Rated Voltage Applied for 2 Minutes)
Applicable for Electronic Ballast
Dissipation Factor
W V (V): 160
D.F (%) : 20
High Temperature Load Life at 105°C for 8000~10000
Hours
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz)
120 1K
10K
100K
COEFFICIENT
1
1.8
2
1.6
Temperature Coefficient
TEMPERATURE (°C)
65
85
105
FACTOR
1.70
1.40
1.00
200
20
400
24
450
24
Low Temperature Stability Impedance Ratio (Max.)
W V (V) :
160
200
400
450
Z - 25°C / Z + 20°C
3
3
5
6
Z - 40°C / Z + 20°C
6
6
6
Endurance: The following specifications shall be satisfied when the capacitors are stored at 20°C after
subjected to DC Voltage with the maximum ripple current which is applied for 10,000 hours (8000
hours for 10ø) at 105°C.
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceeding 200% of Initial Requirement
(c) Leakage Current : Not Exceeding the Initial Requirement
Shelf Life : After having been placed at 105°C without voltage applied for 1000 hours, the capacitors
shall meet the same requirements as Endurance.
diagram of dimensions
Dimensions: mm
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Rubber End Seal
F
dø
10.0
5.0
0.6
7.5
0.8
12.0
F±0.5
F±0.5
Dø
13.0
16.0
L
15Min.
5Min.
D±0.5
L
L ≤ 16 L + 1.5Max.
l > 16 L + 2Max.
Dø = 8 & 10 L + 2.5Max.
15Min.
5Min.
D±0.5
Dø < 20 Dø + 0.5
Dø ≥ 20 Dø + 1
18.0
22.0
10.0
49
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
160 (200)
SIZE
450 (500)
SIZE
RIPPLE
3.3
10 x 15
100
4.7
10 x 19.5
140
10 x 19.5
150
12.5 x 20
180
RIPPLE
200 (250)
SIZE
RIPPLE
6.8
10 x 19.5
10
22
33
47
68
100
150
220
330
400 (450)
SIZE
10 x 19.5
10 x 19.5
500
440
10 x 19.5
520
12.5 x 20
580
13 x 20
660
10 x 19.5
580
12.5 x 20
660
12 x 25
720
13 x 25
720
16 x 20
760
16 x 20
760
13 x 25
970
16 x 25
1120
16 x 20
1120
16 x 25
1120
18 x 20
1120
16 x 25
1200
16 x 32
1280
16 x 32
1300
18 x 25
1300
16 x 32
1300
18 x 25
1300
18 x 36
1380
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
RIPPLE
150
10 x 19.5
180
12.5 x 20
310
16 x 20
300
16 x 25
560
18 x 20
550
16 x 32
620
18 x 25
590
16 x 36
880
18 x 32
880
16 x 25
16 x 32
18 x 32
520
700
870
Yageo corporation ELECTROLYTIC CAPACITORS
Miniature Aluminum
Electrolytic Capacitors
SB [ For Low Leakage Current ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors
electrical characteristics
Operating Temperature Range : -40 ~ +105°C
Rated Voltage Range : 6.3 ~ 100V
Rated Capacitance Range : 0.1 ~ 4700µF
Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C
description
DC Leakage Current (µA) : I = 0.002CV (µA) or 0.4µA whichever is greater.
(After Rated Voltage Applied for 2 Minutes)
Used in where low leakage current is essential as in
coupling of pre-amplifies.
Dissipation Factor
W V (V): 6.3
10
16
25
35 50 ~ 100
D.F. (%) : 24
20
16
14
12
10
When nominal capacitance is over 1000μF, tan δ shall be added 0.02 to the listed value with increase
of every 1000μF
Very low leakage current remains even after prolonged
storage.
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz) 50
120
300
1K
10K
6.3~25V
0.85 1.00
1.04
1.08
1.19
26~50V
0.80 1.00
1.30
1.40
1.43
50~100V
0.77 1.00
1.34
1.43
1.48
70
85
105
1.20
1.00
Temperature Coefficient
TEMPERATURE (°C)
60
FACTOR
1.95 1.75
Low Temperature Stability Impedance Ratio (Max.)
W V (V) :
6.3
Impedance: Z(120Hz) Z - 25°C / Z + 20°C
4
Z(120Hz)Z - 40°C / Z + 20°C
8
10
3
6
16 ~ 25
2
4
35 ~ 63
2
3
80 ~ 100
1.5
2
Endurance: After the rated voltage has been applied at 105°C for 1000 hours, the capacitors shall
meet the following requirements.
(a) Capacitance Change : Within 25% of Initial Value
(b) Dissipation Factor : Not Exceeding 200% of Specified Value
(c) Leakage Current : Not Exceeding the Specified Value
Shelf Life : After having been placed at 105°C without voltage application for 500 hours,
(a) Capacitance Change : Within 25% of Initial Value
(b) Dissipation Factor : Not Exceeding 200% of Specified Value
(c) Leakage Current : Not Exceeding 200% of Specified Value
diagram of dimensions
Dimensions: mm
Rubber Stand-off
Rubber End Seal
Vinyl Sleeve
F±0.5
F±0.5
Dø±0.5
dø
F
1.5
dø
0.45
5.0
2.0
0.5
6.3
2.5
8.0
3.5
10.0
5.0
0.6
12.0
L
Dø < 20 Dø + 0.5
Dø ≥ 20 Dø + 1
Dø
4.0
L ≤ 16 L + 1.5Max.
L > 16 L + 2Max.
Dø = 8 & 10 L + 2.5Max.
15Min.
5Min.
13.0
16.0
7.5
18.0
22.0
10.0
0.8
51
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
6.3 (8)
SIZE
16 (20)
SIZE
RIPPLE
10
5 x 11
40
15
5 x 11
56
RIPPLE
10 (13)
SIZE
RIPPLE
22
5 x 11
68
6.3 x 11
70
33
6.3 x 11
78
6.3 x 11
95
47
6.3 x 11
106
6.3 x 11
100
8 x 11
122
68
6.3 x 11
80
6.3 x 11
142
8 x 11
168
100
6.3 x 11
126
8 x 11
179
8 x 11
210
10 x 12
264
10 x 15
416
150
8 x 11
196
8 x 11
220
10 x 12
280
220
10 x 12
272
10 x 15
355
10 x 19.5
553
330
10 x 15
388
10 x 19.5
480
13 x 20
732
470
10 x 19.5
507
13 x 20
640
13 x 20
1040
680
13 x 20
700
13 x 20
848
13 x 25
1280
820
13 x 25
850
13 x 25
980
16 x 25
1450
1000
13 x 25
896
13 x 25
1081
16 x 25
1700
1500
13 x 25
1204
16 x 25
1376
16 x 32
1750
2200
16 x 25
1513
16 x 32
1680
18 x 36
1900
3300
16 x 36
1902
16 x 36
2155
18 x 40
2250
4700
18 x 36
2272
18 x 40
2560
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
52
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
25 (32)
SIZE
50 (63)
SIZE
RIPPLE
0.10
5 x 11
1
0.15
5 x 11
4
0.22
5 x 11
4
0.33
5 x 11
6
0.47
5 x 11
7
0.56
5 x 11
7
0.68
5 x 11
9
1.0
5 x 11
18
1.5
5 x 11
24
2.2
5 x 11
30
3.3
5 x 11
36
RIPPLE
35 (44)
SIZE
RIPPLE
4.7
5 x 11
27
5 x 11
40
6.3 x 11
45
6.8
5 x 11
42
5 x 11
45
6.3 x 11
55
10
6.3 x 11
63
5 x 11
55
8 x 11
82
6.3 x 11
67
15
6.3 x 11
67
8 x 11
75
8 x 11
97
22
6.3 x 11
61
8 x 11
97
10 x 12
127
8 x 11
84
33
8 x 11
102
10 x 12
139
10 x 15
156
47
10 x 12
141
10 x 12
166
10 x 15
217
68
10 x 12
190
10 x 15
238
10 x 19.5
300
100
10 x 15
277
8 x 11
200
13 x 20
390
10 x 19.5
310
150
10 x 19.5
455
13 x 20
491
13 x 25
569
220
13 x 20
590
13 x 25
630
16 x 25
910
330
13 x 25
754
10 x 15
450
16 x 32
986
16 x 25
771
470
16 x 25
1110
16 x 25
1150
16 x 36
1249
680
16 x 32
1385
16 x 32
1462
16 x 36
1870
820
16 x 32
1540
16 x 36
1630
16 x 36
1950
1000
16 x 36
1710
18 x 36
1723
18 x 40
2070
1500
16 x 36
1779
18 x 40
2006
2200
18 x 40
2174
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
53
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
Rated Voltage w v (SURGE VOLTAGE W V)
63 (79)
SIZE
RIPPLE
80 (100)
SIZE
RIPPLE
100 (125)
SIZE
RIPPLE
0.10
5 x 11
1
5 x 11
1
5 x 11
1
0.15
5 x 11
4
5 x 11
4
5 x 11
4
0.22
5 x 11
4
5 x 11
4
5 x 11
4
0.33
5 x 11
6
5 x 11
6
5 x 11
6
0.47
5 x 11
7
5 x 11
7
5 x 11
7
0.56
5 x 11
7
5 x 11
7
5 x 11
7
0.68
5 x 11
9
5 x 11
9
5 x 11
9
1.0
4x7
12
5 x 11
18
5 x 11
18
5 x 11
18
1.5
5 x 11
24
5 x 11
24
5 x 11
24
2.2
5 x 11
30
5 x 11
30
6.3 x 11
30
3.3
5 x 11
36
6.3 x 11
36
8 x 11
36
4.7
6.3 x 11
45
6.3 x 11
45
8 x 11
60
6.8
6.3 x 11
55
8 x 11
60
10 x 12
67
10
8 x 11
82
10 x 12
90
10 x 15
94
15
10 x 12
103
10 x 15
112
10 x 19.5
117
22
10 x 15
148
10 x 15
165
10 x 19.5
187
33
10 x 15
210
10 x 19.5
217
13 x 20
225
47
10 x 19.5
240
10 x 19.5
276
13 x 25
285
68
10 x 19.5
328
13 x 20
361
13 x 25
375
100
13 x 25
420
13 x 25
447
16 x 25
456
150
13 x 25
648
16 x 25
663
16 x 32
707
220
16 x 32
930
16 x 32
970
16 x 36
1010
330
16 x 36
1088
16 x 36
1198
18 x 36
1377
470
18 x 36
1385
18 x 36
1509
680
18 x 36
1870
820
18 x 40
1950
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
Yageo corporation ELECTROLYTIC CAPACITORS
Miniature Aluminum
Electrolytic Capacitors
SN [ For Non-Polar ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors For
Non-Polar General Purpose
Electrical Characteristics
Operating Temperature Range : -40 ~ +105°C / -25 ~ +105°C
Rated Voltage Range : 6.3 ~ 100V / 160 ~ 250V
Rated Capacitance Range : 0.22 ~ 2200μF / 0.47 ~ 100μF
Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C
description
DC Leakage Current (µA) : I = 0.03 CV + 3µA
(After Rated Voltage Applied for 2 Minutes)
Non-polar for used in reversing polarity DC voltage
circuits.
Dissipation Factor
W V (V): 6.3
10
16
25
35
50
63 ~ 100
160 ~ 250
D.F. (%) : 24
20
17
15
14
12
10
20
For capacitors whose capacitance exceeds 1000µF. The value of D.F is increased by 2% for every
addition of 1000µF.
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz)
60
FACTOR
0.75 1.00 1.20 1.32 1.65
120 300 1K
10K
Temperature Coefficient
TEMPERATURE (°C)
65
85
105
FACTOR
1.30
1.20
1.00
Endurance : 1000 Hours at 105°C with the Polarity Inverted Every 250 Hours
(a) Capacitance Change : Within 25% of Initial Value
(b) Dissipation Factor : Not Exceeding 200% of Specified Value
(c) Leakage Current : Not Exceeding the Specified Value
Shelf Life : After having been placed at 105°C without voltage applied for 500 hours, the capacitors
shall meet the same requirements as Endurance.
diagram of dimensions
Dimensions: mm
Rubber Stand-off
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Dø
F
dø
4.0
1.5
0.45
5.0
2.0
0.5
6.3
2.5
F±0.5
F±0.5
8.0
3.5
10.0
5.0
0.6
12.0
L
15Min.
5Min.
D±0.5
L
L ≤ 16 L + 1.5Max.
L > 16 L + 2Max.
Dø = 8 & 10 L + 2.5Max.
15Min.
5Min.
D±0.5
Dø < 20 Dø + 0.5
Dø ≥ 20 Dø + 1
13.0
16.0
7.5
18.0
22.0
10.0
0.8
55
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
6.3 (8)
SIZE
RIPPLE
10 (13)
SIZE
RIPPLE
16 (20)
SIZE
RIPPLE
25 (32)
SIZE
RIPPLE
4.7
10
6.3 x 11
22
5 x 11
57
45
5 x 11
42
6.3 x 11
50
5 x 11
59
6.3 x 11
69
6.3 x 11
69
8 x 11
86
35 (44)
SIZE
RIPPLE
5 x 11
34
6.3 x 11
54
8 x 11
94
33
5 x 11
63
6.3 x 11
77
8 x 11
98
8 x 11
105
10 x 12
125
47
6.3 x 11
84
6.3 x 11
93
8 x 11
115
10 x 12
140
10 x 15
165
100
8 x 11
140
8 x 11
193
8 x 11
140
10 x 19.5
240
13 x 20
285
10 x 12
175
10 x 15
205
220
10 x 12
235
10 x 15
255
10 x 19.5
330
13 x 20
390
16 x 25
520
330
10 x 15
310
10 x 19.5
380
13 x 20
445
16 x 25
580
16 x 25
630
470
10 x 19.5
400
13 x 20
470
13 x 25
570
16 x 25
690
16 x 32
820
1000
13 x 25
690
16 x 25
885
16 x 32
1020
2200
16 x 32
1250
16 x 36
1450
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
56
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
50 (63)
SIZE
RIPPLE
63 (79)
SIZE
RIPPLE
80 (100)
SIZE
RIPPLE
100 (125)
SIZE
RIPPLE
0.22
5 x 11
5
0.47
5 x 11
11
5 x 11
11
5 x 11
11
5 x 11
14
1.0
5 x 11
17
5 x 11
17
5 x 11
17
5 x 11
21
2.2
5 x 11
25
5 x 11
25
5 x 11
29
6.3 x 11
34
3.3
6.3 x 11
31
6.3 x 11
37
6.3 x 11
39
8 x 11
49
4.7
5 x 11
34
5 x 11
37
8 x 11
47
8 x 11
58
6.3 x 11
41
6.3 x 11
44
6.3 x 11
56
8 x 11
74
10 x 12
88
8 x 11
80
8 x 11
70
10 x 12
100
6.3 x 11
75
8 x 11
95
8 x 11
97
10 x 15
130
10 x 12
115
8 x 11
110
8 x 11
115
10 x 15
150
10 x 19.5
175
8 x 11
130
13 x 20
10 x 19.5
190
100
13 x 20
310
220
16 x 25
570
330
16 x 36
790
10
22
33
47
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
10 x 19.5
150
13 x 20
180
13 x 20
205
13 x 20
220
230
13 x 20
245
13 x 25
285
16 x 25
410
16 x 25
435
16 x 32
510
16 x 32
660
57
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
Rated Voltage w v (SURGE VOLTAGE W V)
160 (200)
SIZE
RIPPLE
200 (250)
SIZE
RIPPLE
250 (300)
SIZE
RIPPLE
0.47
6.3 x 11
14
1.0
6.3 x 11
21
6.3 x 11
21
8 x 11
25
2.2
8 x 11
34
8 x 11
34
10 x 12
38
3.3
10 x 12
49
10 x 12
49
10 x 12
49
4.7
10 x 12
58
10 x 15
62
10 x 17
66
10
10 x 17
80
13 x 20
100
13 x 20
100
22
13 x 25
180
13 x 25
180
16 x 26
200
33
16 x 26
220
16 x 26
220
16 x 32
250
47
16 x 26
285
16 x 32
315
16 x 36
330
100
18 x 36
510
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
Yageo corporation ELECTROLYTIC CAPACITORS
Miniature Aluminum
Electrolytic Capacitors
SR [ For Horizontal Deflection ]
Bi-Polarized Capacitors for Horizontal Deflection Circuits of TV Sets
Electrical Characteristics
Operating Temperature Range : -40 ~ +85°C
Rated Voltage Range : 25, 35, 50V
Rated Capacitance Range : 2.2 ~ 47μF
Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C
description
DC Leakage Current : 100μA Max.
( After 2 Minutes Both Direction )
Bi-Polarized Type for Used in Horizontal Deflection
Current
Dissipation Factor :
W V (V): 25
35
D.F. (%) : 5
5
Correction at High Frequency and High Ripple Currents
Lower Cost Compared with other Film Capacitors
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz) 60
FACTOR
120
0.4 0.4
400~1K 15.75K
0.8
1.0
50
5
Endurance: After the rated voltage has been applied at 85°C for 1000 hours (Polarity Inverted Every
250 Hours) The Capacitors Shall Meet the Following Requirements.
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceeding 150% of Specified Value
(c) Leakage Current : Not Exceeding the Specified Value
Shelf Life : After having been placed at 85°C without voltage applied for 500 hours, the capacitors
shall meet the same requirements as Endurance.
Temperature Coefficient
TEMPERATURE (°C)
65
70
85
FACTOR
1.15
1.00
0.80
diagram of dimensions
Dimensions: mm
Rubber Stand-off
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
F±0.5
F±0.5
L
15Min.
5Min.
D±0.5
L
L ≤ 16 L + 1.5Max.
L > 16 L + 2Max.
Dø = 8 & 10 L + 2.5Max.
15Min.
5Min.
Dø
F
dø
12.0
5.0
0.6
7.5
0.8
10.0
0.8 (1.0)
13.0
D±0.5
Dø < 20 Dø + 0.5
Dø ≥ 20 Dø + 1
16.0
18.0
22.0
59
case size & permissible ripple current of standard products
CAP. (µF)
D x L: mm
Rated Voltage W V (SURGE VOLTAGE W V)
25 (32)
SIZE
RIPPLE
35 (44)
SIZE
RIPPLE
50 (63)
SIZE
RIPPLE
2.2
16 x 25
6
16 x 25
6
16 x 25
6
3.3
16 x 25
7
16 x 25
7
16 x 25
7
4.7
16 x 25
7
16 x 25
7
16 x 25
7
5.6
16 x 32
7
16 x 32
7
16 x 32
7
6.8
16 x 36
8
16 x 36
8
16 x 36
8
8.2
16 x 36
8
16 x 36
8
16 x 36
8
10
18 x 40
12
18 x 40
12
18 x 40
12
13
18 x 40
12
18 x 40
12
18 x 40
12
15
18 x 40
12
18 x 40
12
18 x 40
12
18
22 x 40
13
22 x 40
13
22 x 40
13
20
22 x 40
13
22 x 40
13
22 x 40
13
22
22 x 40
13
22 x 40
13
22 x 40
13
25
22 x 40
13
22 x 40
13
22 x 40
13
47
22 x 40
13
22 x 40
13
22 x 40
13
Note: 1. Ripple Current: (Ap-p) / Sawtooth Waveform 85°C, 15.75KHz
Yageo corporation ELECTROLYTIC CAPACITORS
Miniature Aluminum
Electrolytic Capacitors
SC
[ Low Impedance and Low ESR Suitable
for Motherboard Output Termination ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors For
High Frequency Applications
Electrical Characteristics
Operating Temperature Range : -40 ~ +105°C
Rated Voltage Range : 6.3 ~ 100V
Rated Capacitance Range : 4.7 ~ 15000µF
Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C
description
DC Leakage Current (μA) : I = 0.01CV or 3μA whichever is greater.
Applicable for switching regulator of compurters,
especially for high frequency
Dissipation Factor
(After Rated Voltage Applied for 2 Minutes)
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
W V (V) :
6.3
10
16
25
35
50
63
100
D.F. (%) :
22
19
16
14
12
10
9
8
When nominal capacitance is over 1000μF, tan δ shall be added 0.02 to listed value with increase of every
FREQUENCY (Hz)
50
120 300 1K
10K
~4.7µF
0.30 0.40 0.50 0.70 0.80
5.6~33µF
0.40 0.50 0.60 0.80 0.90
34~330µF
0.60 0.70 0.80 0.90 0.95
1000μF.
W V (V) :
Impedance :
6.3
10
16
25
35
50
63
100
Z(120Hz) Z - 25°C / Z + 20°C
4
3
3
3
3
2
2
2
Z(120Hz)Z - 40°C / Z + 20°C
8
6
4
4
4
4
4
4
331~1000µF
0.65 0.90 0.90 0.98 1.00
Endurance : After the rated voltage has been applied at 105°C for 3000 hours, the capacitors shall meet the
1200µF Higher
0.85 0.90 0.95 0.98 1.00
following requirements.
If Dimension is Down Size, Endurance will be Less 1000 hours than Standard
(a) Capacitance Change : Within ±20% of Initial Value
(b) Dissipation Factor: Not Exceeding 200% of Specified Value
CASE SIZE 5x11 ~ 10x12 10x15 higher
(c) Leakage Current: Not Exceeding the Specified Value
LIFE
2000
3000
Shelf Life : After having been placed at 105°C without voltage applied for 1000 hours, the capacitors shall
meet the same requirements as Endurance.
diagram of dimensions
Dimensions: mm
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Dø
F
dø
4.0
1.5
0.45
5.0
2.0
0.5
6.3
2.5
F±0.5
F±0.5
8.0
3.5
10.0
5.0
0.6
12.0
L
15Min.
5Min.
D±0.5
L
L ≤ 16 L + 1.5Max.
L > 16 L + 2Max.
Dø = 8 & 10 L + 2.5Max.
15Min.
5Min.
D±0.5
Dø < 20 Dø + 0.5
Dø ≥ 20 Dø + 1
13.0
16.0
7.5
0.8
10.0
0.8 (1.0)
18.0
22.0
61
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
6.3 (8)
SIZE
RIPPLE
ESR
10 (13)
SIZE
RIPPLE
ESR
16 (20)
SIZE
RIPPLE
ESR
10
47
25 (32)
SIZE
RIPPLE
ESR
*4 x 7
40
2.000
5 x 11
50
0.550
5 x 11
150
0.450
56
5 x 11
100
0.630
5 x 11
150
0.420
68
5 x 11
150
0.420
6.3 x 11
200
0.370
100
5 x 11
150
0.420
5 x 11
200
0.370
6.3 x 11
250
0.220
120
5 x 11
200
0.370
6.3 x 11
250
0.320
8 x 11
300
0.200
150
5 x 11
200
0.420
6.3 x 11
250
0.320
6.3 x 11
300
0.220
8 x 11
550
0.140
220
6.3 x 11
250
0.320
6.3 x 11
300
0.220
8 x 11
550
0.140
*8 x 11
620
0.120
8 x 15
750
0.100
270
*6.3 x 11 300
0.220
330
*6.3 x 11 320
0.230
8 x 11
0.180
470
680
400
8 x 11
550
0.140
0.120
*8 x 15
660
0.100
8 x 15
750
0.100
8 x 20
800
0.069
10 x 12
688
0.080
10 x 15
900
0.086
0.180
*8 x 11
620
0.120
*8 x 15
730
0.093
*8 x 20
1000
0.067
8 x 11
0.140
8 x 15
750
0.100
10 x 12
800
0.085
*10 x 12
900
0.086
10 x 15
1050
0.064
550
580
0.120
*8 x 11
640
0.110
8 x 15
700
0.100
10 x 12
800
0.085
820
8 x 20
750
0.085
10 x 15
1050
1000
*8 x 11
580
0.150
8 x 20
*8 x 15
670
0.085
8 x 20
800
10 x 12
10 x 15
1500
620
*6.3 x 11 440
*8 x 11
1200
*8 x 11
10 x 15
1050
0.064
10 x 19.5
1100
0.039
0.064
10 x 19.5
1100
0.044
10 x 19.5
1250
0.039
1080
0.065
*10 x 15
1140
0.043
*10 x 19.5 1160
0.047
10 x 12
930
0.075
10 x 19.5
1250
0.039
*10 x 25
1310
0.042
0.069
10 x 15
990
0.085
13 x 20
1450
0.038
690
0.080
10 x 19.5
1100
0.050
1000
0.064
10 x 19.5
1250
0.044
13 x 25
1600
0.029
*8 x 15
980
0.085
*8 x 20
1070
0.051
*10 x 15
1070
0.055
10 x 19.5 1250
0.044
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω Max.)
3. * Down Size: 1000 Hours less than standard
10 x 19.5
1450
0.039
*10 x 25
1310
0.042
13 x 20
1450
0.038
*10 x 19.5 1200
0.045
*12 x 30
1750
0.032
13 x 20
0.034
16 x 25
2000
0.028
1600
62
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
6.3 (8)
SIZE
ESR
16 (20)
SIZE
RIPPLE
ESR
25 (32)
SIZE
RIPPLE
ESR
*10 x 19.5 1330
0.047
*10 x 30
1780
0.032
*13 x 30
1810
0.029
0.048
*10 x 25
1450
0.039
*13 x 20
1720
0.033
*16 x 25
1660
0.032
1450
0.043
13 x 20
1600
0.038
13 x 25
2000
0.028
16 x 32
2200
0.024
*10 x 25 1400
0.043
*10 x 30
1740
0.032
*13 x 40
2200
0.026
*16 x 36
2540
0.019
13 x 25
1700
0.035
13 x 25
2000
0.028
16 x 25
2200
0.024
18 x 36
2550
0.019
3900
13 x 25
1750
0.032
4700
*12 x 30
1570
0.033
*13 x 25
1860
0.028
16 x 36
2550
0.019
18 x 36
2800
0.019
*13 x 25
1520
0.032
16 x 25
2200
0.024
16 x 25
1800
0.028
6800
16 x 32
2000
0.024
16 x 36
2550
0.019
18 x 36
2800
0.019
18 x 36
2800
0.019
8200
16 x 32
2350
0.019
18 x 36
2800
0.019
10000
16 x 36
2550
0.019
15000
18 x 36
3000
0.019
2200
3300
ESR
10 (13)
SIZE
*10 x 19.5 1220
0.051
*10 x 25
1310
13 x 20
RIPPLE
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω Max.)
3. * Down Size: 1000 Hours less than standard
RIPPLE
63
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
35 (44)
SIZE
RIPPLE
ESR
50 (63)
SIZE
RIPPLE
ESR
63 (79)
SIZE
RIPPLE
ESR
100 (125)
SIZE
RIPPLE
ESR
4.7
5 x 11
115
1.200
5 x 11
115
2.000
5 x 11
115
2.200
5 x 11
120
2.000
6.8
5 x 11
120
1.000
5 x 11
120
1.850
5 x 11
120
2.000
5 x 11
140
1.850
10
5 x 11
140
0.900
5 x 11
140
1.700
5 x 11
140
1.850
6.3 x 11
200
1.500
15
5 x 11
170
0.690
5 x 11
180
1.200
5 x 11
200
1.700
6.3 x 11
250
1.200
22
5 x 11
190
0.420
5 x 11
200
0.700
6.3 x 11
250
1.200
8 x 11
300
0.790
33
5 x 11
200
0.420
6.3 x 11
250
0.600
6.3 x 11
300
0.900
8 x 15
450
0.590
47
6.3 x 11
250
0.370
6.3 x 11
300
0.520
8 x 11
450
0.700
10 x 15
550
0.350
68
6.3 x 11
300
0.220
8 x 11
450
0.350
8 x 11
550
0.520
10 x 19.5
650
0.240
100
*6.3 x 11 360
0.180
*8 x 11
480
0.290
8 x 20
650
0.350
13 x 20
800
0.180
8 x 11
450
0.140
8 x 15
550
0.250
120
8 x 11
550
0.130
8 x 20
650
0.210
10 x 15
800
0.300
13 x 25
1050
0.150
150
8 x 15
650
0.100
10 x 12
800
0.160
10 x 15
1050
0.200
13 x 25
1300
0.110
220
*8 x 15
730
0.100
*10 x 15
1050
0.100
10 x 19.5
1300
0.150
16 x 25
1400
0.071
10 x 12
800
0.069
10 x 25
1050
0.068
*10 x 15
900
0.052
10 x 19.5
1300
0.072
13 x 20
1400
0.100
16 x 32
1550
0.049
*10 x 19.5 1390
0.075
13 x 25
1550
0.064
18 x 36
1770
0.038
13 x 20
1400
0.060
330
470
10 x 19.5 1050
0.044
10 x 19.5 1300
0.039
680
13 x 20
1400
0.038
13 x 25
1550
0.050
16 x 25
1700
0.052
820
13 x 20
1550
0.034
16 x 25
1700
0.040
16 x 32
1900
0.048
1000
13 x 25
1700
0.029
16 x 25
1900
0.039
16 x 32
2100
0.042
1200
16 x 25
1900
0.028
16 x 32
2100
0.025
16 x 36
2550
0.036
1500
16 x 25
2100
0.024
16 x 36
2550
0.025
18 x 36
2800
0.033
2200
*16 x 32
2300
0.021
18 x 40
2800
0.025
16 x 36
2550
0.019
18 x 36
2880
0.019
3300
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω Max.)
3. * Down Size: 1000 Hours less than standard
Yageo corporation ELECTROLYTIC CAPACITORS
Miniature Aluminum
Electrolytic Capacitors
S J [ Low Impedance and High Ripple Series ]
105°C 1000 ~ 5000 Hours, Low Impedance and High Ripple Current
Electrical Characteristics
Operating Temperature Range : -40 ~ +105°C
Rated Voltage Range : 6.3 ~ 100V
Rated Capacitance Range : 5.6 ~ 6800µF
Capacitance Tolerance : -20 ~ +20% at 120KHz
description
DC Leakage Current (µA) : I = 0.01 CV (µA) or 3µA whichever is greater.
AV (TV, Video, Audio), Monitor / Computer, OA / HA
/ Communication, Converter / Inverter, Adapter, SMPS
Dissipation Factor
W V (V): 6.3
D.F. (%) : 22
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz)
50
5.6~390µF
0.60 0.70 0.85 0.95 1.00
120 1K
10K 100K
470~1000µF
0.65 0.75 0.90 0.98 1.00
1200~6800µF
0.75 0.80 0.95 1.00 1.00
ENDURANCE
CASE
LIFE TIME (HOURS)
L=7
1000
L ≥ 11
Dø ≤ 6.3
2000
Dø = 8
3000
Dø = 10
4000
Dø ≥ 13
5000
10
19
16
16
W V (V) :
Impedance: Z - 25°C / Z + 20°C
Z - 40°C / Z + 20°C
25
14
35
12
6.3
2
3
10
2
3
50
10
16
2
3
63
9
25
2
3
100
8
35
2
3
50
2
3
Shelf Life: After having been placed at 105°C without voltage applied for 1000 hours. (500 hours for L=7)
The capacitors shall meet the same requirements as Endurance.
Dimensions: mm
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Rubber End Seal
15Min.
5Min.
F±0.5
F±0.5
L
D±0.5
100
2
3
Endurance: After the rated voltage and maximum ripple current have been applied at 105°C for 1000
~ 5000 hours, the capacitors shall meet the following requirements.
(a) Capacitance Change: Within±25% of the Initial Value
(b) Dissipation Factor: Not Exceeding 200% of the Specified Value
(c) Leakage Current: Not Exceeding the Specified Value
diagram of dimensions
Vinyl Sleeve
(P.V.C)
63
2
3
L
L ≤ 16 L + 1.5Max.
L > 16 L + 2Max.
Dø = 8 & 10 L + 2.5Max.
15Min.
5Min.
D±0.5
Dø < 20 Dø + 0.5
Dø ≥ 20 Dø + 1
Dø
F
dø
4.0
1.5
0.45
5.0
2.0
0.5
6.3
2.5
8.0
3.5
10.0
5.0
0.6
13.0
16.0
18.0
7.5
0.8
65
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
6.3 (8)
SIZE
RIPPLE ESR
10 (13)
SIZE
RIPPLE ESR
16 (20)
SIZE
RIPPLE ESR
25 (32)
SIZE
RIPPLE ESR
10
15
18
35 (44)
SIZE
RIPPLE ESR
4x7
130
0.96
4x7
130
0.94
5x7
190
0.57
4x7
130
0.92
5x7
170
0.69
5x7
210
0.47
27
4x7
130
0.89
5x7
190
0.61
5x7
210
0.46
5 x 11
230
0.37
33
5x7
160
0.75
5x7
210
0.45
5 x 11
220
0.42
5 x 11
250
0.30
39
4x7
130
0.85
5x7
175
0.64
5 x 11
220
0.43
5 x 11
230
0.36
6.3 x 7
300
0.25
47
5x7
175
0.70
5x7
190
0.53
5 x 11
230
0.36
5 x 11
250
0.30
6.3 x 11 380
0.15
8x7
350
0.19
6.3 x 11 410
0.13
8x7
380
0.16
8 x 11
510
0.12
8 x 11
620
0.105
56
68
100
120
150
180
5x7
5x7
190
210
0.56
0.43
5 x 11
200
0.43
6.3 x 7
240
0.35
5 x 11
220
0.38
6.3 x 7
270
0.29
5 x 11
250
0.30
6.3 x 7
300
0.23
8x7
340
0.18
5x7
5 x 11
5 x 11
6.3 x 7
210
210
250
300
0.44
0.44
0.30
0.23
5 x 11
6.3 x 7
250
300
0.30
0.24
6.3 x 7
300
0.24
6.3 x 11 340
0.19
8x7
310
0.22
6.3 x 11 370
0.16
6.3 x 11 410
0.13
8x7
350
0.18
8x7
380
0.15
6.3 x 11 410
0.13
8 x 11
560
0.12
8 x 11
680
0.088
8x7
380
0.15
8x7
350
0.18
8 x 11
510
0.12
8 x 11
630
0.105
8 x 11
760
0.072
8x7
380
0.15
8 x 11
560
0.11
8 x 11
690
0.088
8 x 15
910
0.068
10 x 12 930
0.065
220
8x7
380
0.15
6.3 x 11 410
0.13
8 x 11
620
0.10
8 x 11
760
0.072
10 x 12 1030
0.053
270
6.3 x 11 370
0.16
8 x 11
0.12
8 x 11
690
0.088
8 x 15
900
0.068
8 x 20
1250
0.041
10 x 12 930
0.065
580
330
6.3 x 11 410
0.13
8 x 11
640
0.10
8 x 11
760
0.072
10 x 12 1030
0.053
10 x 15 1430
0.038
470
8 x 11
0.086
8 x 11
760
0.072
8 x 15
1000
0.056
8 x 20
1250
0.041
10 x 19.5 1820
0.026
10 x 12 1030
0.053
10 x 15 1430
0.038
10 x 19.5 1650
0.032
10 x 25 2150
0.023
10 x 19.5 1820
0.026
13 x 20 2360
0.023
560
680
8 x 11
8 x 15
680
760
900
0.072
0.062
8 x 15
910
0.068
8 x 20
1140
0.049
10 x 12 940
0.064
10 x 15 1300
0.046
10 x 12 1030
0.053
8 x 20
1250
0.041
10 x 15 1430
0.038
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω Max.)
66
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
820
1000
1200
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
6.3 (8)
SIZE
RIPPLE ESR
10 (13)
SIZE
RIPPLE ESR
16 (20)
SIZE
RIPPLE ESR
25 (32)
SIZE
RIPPLE ESR
35 (44)
SIZE
RIPPLE ESR
8 x 15
1000
8 x 20
10 x 19.5 1650
0.032
10 x 25 2150
0.023
13 x 25 2510
0.02
10 x 19.5 1820
0.026
13 x 20 2360
0.021
13 x 25 2770
0.018
10 x 25 2150
0.023
13 x 25 2510
0.02
13 x 30 3290
0.016
16 x 20 3140
0.018
10 x 12
1030
0.056
0.053
1130
0.05
10 x 15 1300
0.046
8 x 20
1250
0.041
10 x 15 1430
0.038
10 x 19.5 1820
0.026
8 x 20
1250
0.041
10 x 15
1430
0.038
1500
10 x 19.5 1820
0.026
10 x 25 2150
0.023
13 x 20 2360
0.021
13 x 25 2770
0.018
13 x 35 3400
0.015
1800
10 x 25
0.025
13 x 20 2230
0..022
13 x 25 2510
0.02
13 x 30 3290
0.016
16 x 25 3460
0.016
16 x 20 3140
0.018
1940
2200
10 x 25
2150
0.023
13 x 20 2360
0.021
13 x 25 2770
0.018
13 x 35 3400
0.015
2700
13 x 20
2230
0.022
13 x 25 2510
0.02
13 x 30 3290
0.016
16 x 25 3460
0.016
16 x 20 3140
0.018
3300
13 x 20
2360
0.021
13 x 25 2770
0.018
13 x 35 3400
0.015
3900
13 x 25
2770
0.018
13 x 30 3290
0.016
16 x 25 3460
0.016
16 x 20 3140
0.018
4700
13 x 30
3290
0.016
13 x 35 3400
0.015
5600
13 x 35
3400
0.015
16 x 25 3460
0.016
16 x 20
3140
0.018
16 x 25
3460
0.016
6800
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω Max.)
67
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
Rated Voltage W V (SURGE VOLTAGE W V)
50 (63)
SIZE
RIPPLE
ESR
5.6
4x7
130
1.00
6.8
5x7
170
10
5x7
15
63 (79)
SIZE
100 (125)
SIZE
RIPPLE
ESR
0.74
5 x 11
125
1.40
210
0.50
6.3 x 11
170
0.95
6.3 x 7
220
0.38
5 x 11
215
0.48
6.3 x 7
300
0.26
5 x 11
240
0.34
27
8x7
340
33
8x7
39
RIPPLE
ESR
5 x 11
136
1.190
6.3 x 11
210
0.57
6.3 x 11
176
0.880
8 x 11
330
0.44
0.21
6.3 x 11
192
0.580
8 x 11
360
0.36
380
0.17
6.3 x 11
216
0.470
8 x 15
375
0.30
6.3 x 11
330
0.16
8 x 11
308
0.420
8 x 15
450
0.25
47
6.3 x 11
360
0.15
8 x 11
336
0.350
10 x 12
450
0.24
56
6.3 x 11
390
0.14
8 x 11
400
0.350
8 x 20
570
0.19
68
8 x 11
600
0.11
8 x 15
488
0.260
10 x 15
580
0.18
10 x 12
500
0.240
8 x 15
536
0.220
10 x 19.5
750
0.13
10 x 12
552
0.200
13 x 16
740
0.13
22
82
8 x 11
660
0.09
100
8 x 11
730
0.074
10 x 15
640
0.160
10 x 25
880
0.12
120
8 x 15
950
0.065
8 x 20
656
0.160
13 x 20
1050
0.094
10 x 15
760
0.150
10 x 19.5
808
0.130
13 x 25
1100
0.085
13 x 16
832
0.130
10 x 19.5
880
0.110
13 x 25
1200
0.071
13 x 16
912
0.110
10 x 25
1040
0.099
13 x 30
1410
0.063
16 x 20
1300
0.071
13 x 35
1560
0.052
16 x 25
1600
0.053
18 x 20
1470
0.069
150
180
220
270
10 x 12
8 x 20
10 x 15
10 x 19.5
980
1190
1370
1580
0.061
0.046
0.042
0.03
13 x 20
1200
0.081
330
10 x 25
1870
0.028
13 x 25
1480
0.058
13 x 40
1700
0.046
390
13 x 20
1870
0.028
13 x 30
1640
0.063
16 x 32
1750
0.041
16 x 20
1448
0.073
18 x 25
1620
0.049
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω Max.)
68
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
470
560
680
820
1000
D x L: mm
Rated Voltage W V (SURGE VOLTAGE W V)
50 (63)
SIZE
RIPPLE
ESR
63 (79)
SIZE
RIPPLE
ESR
100 (125)
SIZE
RIPPLE
ESR
13 x 20
2050
0.027
13 x 30
1800
0.061
16 x 36
1890
0.033
16 x 20
1592
0.061
18 x 32
1780
0.039
13 x 25
1960
0.047
16 x 40
2080
0.03
16 x 25
2040
0.043
18 x 36
2060
0.031
13 x 40
2224
0.039
18 x 40
2570
0.028
18 x 20
1960
0.052
13 x 25
13 x 30
2410
2860
0.023
0.021
13 x 35
2960
0.019
16 x 32
2248
0.035
16 x 20
2730
0.023
18 x 25
2224
0.042
16 x 32
3350
0.021
16 x 36
2227
0.028
18 x 32
2616
0.034
16 x 40
2672
0.026
18 x 36
2648
0.027
18 x 40
2736
0.024
1200
1500
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω Max.)
Yageo corporation ELECTROLYTIC CAPACITORS
SQ
[ For Adapter and Power Supply
Applications Series ]
Miniature Aluminum
Electrolytic Capacitors
105°C 2000 Hours, Wide Temperature Range and Low Impedance
Electrical Characteristics
Operating Temperature Range : -40 ~ +105°C
Rated Voltage Range : 160V ~ 450DC
Rated Capacitance Range : 2.2 ~ 220μF
Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C
DC Leakage Current (μA) : I ≤ 0.03CV + 10μA (After Rated Voltage Applied for 3 Minutes)
I = Leakage Current (μA), C = Nominal Capacitance (μF), V = Rated Voltage (V)
description
Dissipation Factor
W V (V): 160
D.F. (%) : 15
Recommended Applications: AV (TV, Video, Audio),
Monitor / Computer, OA / HA / Communication,
Converter / Inverter, Energy Saving Lamp, PFC Circuit,
SMPS, Ballast, Adapter
200
15
250
15
W V (V) :
Impedance: Z - 25°C / Z + 20°C
Z - 40°C / Z + 20°C
350
24
400
24
160
3
6
450
24
200
3
6
250
3
6
350
3
6
400
3
6
450
3
6
Endurance : After the rated voltage has been applied at 105°C for 2000 hours. The capacitors shall
meet the following reuirements.
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceeding 200% of the Specified Value
(c) Leakage Current : Not Exceeding the Specified Value
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz)
50 120 1K 10K 100K
< 33μF
0.80 1.00 1.36 1.54 1.80
≥ 34μF
0.85 1.00 1.28 1.35 1.40
Shelf Life: After leaving capacitors under no load at 105°C for 1000 hours, the capacitors shall meet
the same requirements as Endurance.
diagram of dimensions
Dimensions: mm
Rubber Stand-off
dø
10.0
5.0
0.6
7.5
0.8
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Rubber End Seal
F±0.5
F
F±0.5
Dø
13.0
L
16.0
18.0
L ≤ 16 L + 1.5Max.
L > 16 L + 2Max.
Dø = 8 & 10 L + 2.5Max.
15Min.
5Min.
D±0.5
Dø < 20 Dø + 0.5
Dø ≥ 20 Dø + 1
L
15Min.
5Min.
D±0.5
70
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
160 (200)
SIZE
RIPPLE
120Hz
200 (250)
SIZE
100KHz
RRIPPLE
120Hz
250 (300)
SIZE
RIPPLE
120Hz
100KHz
10 x 19.5
120
220
100KHz
10
22
10 x 19.5
195
350
10 x 19.5
195
350
13 x 25
165
300
33
13 x 20
315
450
13 x 20
365
520
13 x 25
280
400
47
13 x 25
420
600
13 x 25
420
600
16 x 25
505
720
68
13 x 25
420
600
16 x 25
665
950
16 x 32
570
810
100
16 x 25
665
950
16 x 32
840
1200
18 x 36
735
1050
220
18 x 36
980
1400
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz & 100KHz
71
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
350 (400)
SIZE
400 (450)
SIZE
RIPPLE
120Hz
100KHz
450 (500)
SIZE
RIPPLE
120Hz
100KHz
RIPPLE
120Hz
100KHz
2.2
10 x 15
30
50
10 x 15
80
140
10 x 15
60
110
3.3
10 x 15
35
60
10 x 19.5
110
195
10 x 19.5
75
135
4.7
10 x 19.5
45
78
10 x 25
120
220
13 x 20
105
190
10
13 x 20
75
130
13 x 25
200
360
13 x 25
140
250
22
16 x 25
115
205
16 x 25
315
570
16 x 32
265
480
33
16 x 32
180
255
16 x 32
490
700
18 x 36
455
650
47
18 x 32
225
320
18 x 32
600
860
18 x 36
520
720
18 x 40
720
1000
82
100
18 x 45
370
530
120
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz & 100KHz
Yageo corporation ELECTROLYTIC CAPACITORS
Miniature Aluminum
Electrolytic Capacitors
SY
[ For Low Impedance and Low ESR Suitable
for Motherboard Output Termination ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors for
High Frequency Applications
Electrical Characteristics
Operating Temperature Range : -40 ~ +105°C
Rated Voltage Range : 6.3 ~ 100V
Rated Capacitance Range : 6.8 ~15,000μF
Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C
description
Features: Low ESR, high permissible ripple current at
high frequency and long life than SC
Recommended Applications: Used switching regulator
applications in computers
Especially for high frequency
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz)
120
1K
10K 100K
22~180µF
0.40
0.75
0.90 1.00
220~560µF
0.50
0.85
0.94 1.00
680~1800µF
0.60
0.87
0.95 1.00
2200~3900µF
0.75
0.90
0.95 1.00
4700µF Higher
0.85
0.95
0.98 1.00
Leakage Current (Max.) (20°C): I = 0.01CV or 3μA whichever is greater.
(After Rated Voltage Applied for 2 Minutes)
I = Leakage Current (μA), C = Nominal Capacitance (μF), V = Rated Voltage (V)
Dissipation Factor
W V (V): 6.3
D.F. (%) : 22
10
19
16
16
25
14
35
12
50
10
63
9
100
8
When nominal capacitance is over 1,000uF, tan δ shall be added 0.02 to the listed value with increase
of every 1000μF.
W V (V) : Rated Voltage (V)
6.3
10
16
25
35
50
63
100
Impedance : Z - 25°C / Z + 20°C
4
3
2
2
2
2 2
2
Z - 40°C / Z + 20°C
8
6
4
3
3
3
3
3
Endurance
Dø :
5ø~6.3ø
8ø~10øx12.5 10øx15~12ø
13ø~18ø
Life :
3000hrs
4000hrs
5000hrs
6000hrs
After the rated voltage has been applied at 105°C for 6000 hours. The capacitors shall meet the following requirements.
(a) Capacitance Change : Within 25% of Initial Value
(b) Dissipation Factor : Not Exceeding 200% of Specified Value
(c) Leakage Current : Not Exceeding the Specified Value
Shelf Life : After having beening placed at 105°C without voltage applied for 1000 hours, the capacitors shall meet the same requirements as Endurance.
diagram of dimensions
Dimensions: mm
Rubber Stand-off
Rubber End Seal
Vinyl Sleeve
F±0.5
F±0.5
Dø±0.5
dø
L
Dø < 20 Dø + 0.5
Dø ≥ 20 Dø + 1
L ≤ 16 L + 1.5Max.
L > 16 L + 2Max.
Dø = 8 & 10 L + 2.5Max.
15Min.
5Min.
Dø
F
dø
5.0
2.0
0.5
6.3
2.5
8.0
3.5
10.0
5.0
0.6
12.0
13.0
16.0
18.0
7.5
0.8
73
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
6.3 (8)
SIZE
RIPPLE
ESR
10 (13)
SIZE
RIPPLE
ESR
56
100
5 x 11
210
0.58
120
150
5 x 11
210
6.3 x 11
330
6.3 x 11
340
0.22
470
6.3 x 11
510
0.16
8 x 11
640
16 (20)
SIZE
RIPPLE
ESR
5 x 11
210
0.580
6.3 x 11
250
0.230
6.3 x 11
340
0.220
6.3 x 11
469
0.185
8 x 11
582
0.150
8 x 11
640
0.130
*8 x 15
840
0.087
8 x 20
950
0.078
*10 x 12
865
0.080
10 x 15
1210
0.060
8 x 20
1050
0.069
10 x 15
1210
0.060
0.58
220
680
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
0.13
8 x 11
8 x 15
340
640
840
0.22
0.13
0.087
820
10 x 12
865
0.08
10 x 12
865
0.08
1000
8 x 15
840
0.087
8 x 20
1050
0.069
8 x 20
1050
0.069
10 x 15
1210
0.06
*10 x 15
1210
0.060
10 x 19.5
1400
0.046
13 x 15
1450
0.049
1200
10 x 19.5
1400
0.046
10 x 25
1650
0.042
0.069
10 x 25
1650
0.042
10 x 30
1910
0.031
1210
0.06
13 x 15
1450
0.049
13 x 20
1900
0.035
10 x 19.5
1400
0.046
16 x 15
1940
0.042
1800
13 x 15
1450
0.049
2200
*10 x 19.5
1400
0.046
10 x 30
1910
0.031
13 x 25
2230
0.027
10 x 25
1650
0.042
13 x 20
1900
0.042
18 x 15
2210
0.043
16 x 15
1940
0.042
18 x 15
2210
0.043
13 x 30
2650
0.024
16 x 20
2530
0.027
1500
2700
8 x 20
1050
0.069
10 x 15
1210
0.06
8 x 20
1050
*10 x 15
10 x 30
1910
0.031
16 x 15
1940
0.042
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω Max.)
3. * Down Size: 1000 Hours less than standard
4. For case size 13 x 15, 16 x 15 and 18 x 15, tolerance of height = ±3 mm
74
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
3300
3900
4700
5600
6800
8200
10000
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
6.3 (8)
SIZE
RIPPLE
ESR
10 (13)
SIZE
RIPPLE
ESR
16 (20)
SIZE
RIPPLE
ESR
10 x 25
1650
0.042
10 x 30
1910
0.031
13 x 36
2880
0.020
13 x 20
1900
0.035
13 x 25
2230
0.027
13 x 25
2230
0.027
13 x 30
2650
0.024
13 x 40
3350
0.017
18 x 15
2210
0.043
16 x 20
2530
0.027
16 x 25
2930
0.021
18 x 20
2860
0.026
16 x 32
3450
0.017
18 x 25
3140
0.019
13 x 30
2650
0.024
13 x 35
2880
0.02
13 x 35
2880
0.02
13 x 40
3350
0.017
16 x 36
3610
0.015
16 x 20
2530
0.027
16 x 25
2930
0.021
18 x 32
4170
0.015
18 x 20
2860
0.026
16 x 40
4080
0.013
18 x 36
4220
0.014
18 x 40
4280
0.012
13 x 40
3350
0.017
16 x 32
3450
0.017
16 x 25
2930
0.021
18 x 25
3140
0.019
18 x 20
2860
0.026
16 x 32
3450
0.017
16 x 36
3610
0.015
18 x 32
4170
0.015
16 x 36
3610
0.015
16 x 40
4080
0.013
18 x 25
3410
0.017
18 x 36
4220
0.014
12000
18 x 32
4170
0.015
18 x 40
4280
0.012
15000
18 x 36
4220
0.014
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω Max.)
3. For case size 13 x 15, 16 x 15 and 18 x 15, tolerance of height = ±3 mm
75
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
25 (32)
SIZE
RIPPLE
ESR
35 (44)
SIZE
RIPPLE
ESR
2.2
50 (63)
SIZE
RIPPLE
ESR
5 x 11
85
2.280
4.7
5 x 11
130
2.400
5 x 11
135
2.000
10
5 x 11
275
0.390
5 x 11
100
1.200
5 x 11
180
0.700
22
33
5 x 11
210
0.580
6.3 x 11
245
0.490
6.3 x 11
275
0.390
6.3 x 11
300
0.520
56
6.3 x 11
340
0.220
6.3 x 11
295
0.300
68
6.3 x 11
500
0.170
82
6.3 x 11
540
0.160
6.3 x 11
580
0.150
8 x 11
555
0.170
8 x 15
730
0.120
10 x 12
760
0.120
8 x 20
910
0.091
10 x 15
1050
0.084
10 x 19.5
1220
0.060
13 x 15
1260
0.061
47
100
5 x 11
6.3 x 11
210
340
0.580
0.220
120
150
8 x 11
640
0.160
8 x 11
640
0.130
180
220
8 x 11
640
0.130
270
330
470
820
840
0.087
10 x 12
865
0.080
8 x 20
1050
0.069
8 x 15
840
0.087
*10 x 15
1210
0.060
*10 x 19.5
1400
0.058
10 x 12
865
0.080
10 x 19.5
1400
0.046
10 x 25
1440
0.055
8 x 20
1050
0.069
13 x 15
1450
0.049
13 x 20
1660
0.045
*10 x 12
1050
0.070
16 x 15
1690
0.055
10 x 15
1210
0.060
13 x 25
1950
0.034
18 x 15
1930
0.054
13 x 30
2310
0.030
13 x 36
2510
0.025
16 x 20
2210
0.034
560
680
*8 x 15
10 x 25
1650
0.042
10 x 19.5
1400
0.046
10 x 30
1910
0.031
13 x 15
1450
0.049
13 x 20
1900
0.035
16 x 15
1940
0.042
13 x 20
1900
0.035
10 x 25
1650
0.042
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω Max.)
3. * Down Size: 1000 Hours less than standard
4. For case size 13 x 15, 16 x 15 and 18 x 15, tolerance of height = ±3 mm
76
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
1000
1200
1500
1800
2200
25 (32)
SIZE
RIPPLE
ESR
35 (44)
SIZE
RIPPLE
ESR
50 (63)
SIZE
RIPPLE
ESR
10 x 19.5
1400
0.046
13 x 25
2230
0.027
13 x 40
2920
0.021
10 x 30
1910
0.031
18 x 15
2210
0.043
16 x 25
2555
0.025
13 x 20
1900
0.035
18 x 20
2490
0.036
16 x 15
1940
0.042
18 x 15
2210
0.043
13 x 30
2650
0.024
16 x 32
3010
0.022
16 x 20
2530
0.027
18 x 25
2740
0.026
13 x 35
2880
0.020
16 x 36
3510
0.019
*13 x 20
1900
0.035
13 x 25
2230
0.027
13 x 30
2650
0.024
13 x 40
3350
0.017
16 x 40
3710
0.016
16 x 20
2530
0.027
16 x 25
2930
0.021
18 x 32
3635
0.021
18 x 20
2860
0.026
18 x 36
3680
0.017
18 x 40
3800
0.014
13 x 35
2880
0.020
16 x 32
3450
0.017
18 x 20
2860
0.026
18 x 25
3140
0.019
13 x 40
3350
0.017
16 x 36
3610
0.015
16 x 25
2930
0.021
18 x 32
4170
0.015
16 x 32
3450
0.017
16 x 40
4080
0.013
18 x 25
3140
0.019
18 x 36
4220
0.014
3900
18 x 32
4170
0.015
18 x 40
4280
0.012
4700
18 x 36
4220
0.014
5600
18 x 40
4280
0.012
2700
3300
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω Max.)
3. * Down Size: 1000 Hours less than standard
4. For case size 13 x 15, 16 x 15 and 18 x 15, tolerance of height = ±3 mm
77
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
63 (79)
SIZE
100 (125)
SIZE
RIPPLE
ESR
5 x 11
55
2.30
6.3 x 11
115
1.20
8 x 11
232
0.63
39
8 x 15
300
0.45
47
10 x 12
288
0.43
8 x 20
362
0.33
10 x 15
357
0.31
RIPPLE
ESR
6.8
15
5 x 11
55
2.30
27
33
56
6.3 x 11
8 x 11
115
232
1.20
0.63
68
82
8 x 15
300
0.45
10 x 19.5
466
0.21
10 x 12
288
0.43
13 x 15
466
0.23
10 x 25
531
0.20
100
120
8 x 20
362
0.33
10 x 30
663
0.15
10 x 15
357
0.31
13 x 20
690
0.16
16 x 16
795
0.14
10 x 19.5
466
0.21
13 x 25
784
0.12
13 x 15
466
0.23
18 x 15
920
0.12
10 x 25
531
0.20
13 x 30
905
0.10
16 x 20
1040
0.091
150
180
220
270
330
390
470
10 x 30
663
0.15
13 x 35
1050
0.083
13 x 20
690
0.16
16 x 25
1250
0.073
16 x 16
795
0.14
13 x 25
784
0.12
13 x 40
1180
0.071
18 x 20
1240
0.08
18 x 16
920
0.12
16 x 32
1570
0.054
18 x 25
1490
0.057
13 x 30
905
0.10
16 x 36
1790
0.045
16 x 20
1040
0.091
18 x 32
1630
0.047
13 x 35
1050
0.083
16 x 40
2020
0.04
16 x 25
1250
0.073
13 x 40
1180
0.071
18 x 36
1790
0.04
18 x 20
1240
0.080
820
16 x 32
1570
0.054
18 x 40
2330
0.036
18 x 25
1490
0.057
1000
16 x 36
1790
0.045
18 x 32
1630
0.047
16 x 40
2020
0.04
560
680
1200
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω Max.)
3. For case size 13 x 15, 16 x 15 and 18 x 15, tolerance of height = ±3 mm
Yageo corporation ELECTROLYTIC CAPACITORS
Miniature Aluminum
Electrolytic Capacitors
SZ [ Ultra Low ESR ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors for
High Frequency Applications
Electrical Characteristics
Operating Temperature Range : -40 ~ +105°C
Rated Voltage Range : 6.3 ~ 16V
Rated Capacitance Range : 470 ~ 3300µF
Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C
description
DC Leakage Current (µA) : I = 0.03 CV whichever is greater.
(After Rated Voltage Applied for 2 Minutes)
Used in switching regulator applications in computers,
especially for high frequency.
Dissipation Factor
W V (V) :
6.3
10
16
D.F. (%) :
22
19
16
When nominal capacitance is over 1000μF, tan δ shall be added 0.02 to the listed value with increase
of every 1000μF.
Low impedance and ESR, high permissible ripple
current at high frequency and higher operating
temperature (-40°C to +105°C).
High Temperature Load Life at 105°C for 2000 Hours
W V (V) : Rated Voltage (V)
Impedance: Z - 25°C / Z + 20°C
Z - 40°C / Z + 20°C
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz)
120
1K
10K
100K
FACTOR
0.50
0.80
0.90
1.00
Temperature Coefficient
TEMPERATURE (°C)
65
85
105
FACTOR
2.10
1.70
1.00
6.3
2
3
10
2
3
16
2
3
Endurance: After the rated voltage has been applied at 105°C for 2000 hours, the capacitors shall
meet the following requirements.
(a) Capacitance Change : Within ±25% of Initial Value
(b) Dissipation Factor : Not Exceeding 200% of Specified Value
(c) Leakage Current : Not Exceeding the Specified Value
Shelf Life: After having been placed at 105°C without voltage applied for 1000 hours, the capacitors
shell meet the same requirements as Endurance.
diagram of dimensions
Dimensions: mm
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Rubber End Seal
F±0.5
F±0.5
L
15Min.
5Min.
Dø
F
dø
4.0
1.5
0.45
5.0
2.0
0.5
6.3
2.5
8.0
3.5
10.0
5.0
0.6
12.0
D±0.5
L
L ≤ 16 L + 1.5Max.
L > 16 L + 2Max.
Dø = 8 & 10 L + 2.5Max.
15Min.
5Min.
D±0.5
Dø < 20 Dø + 0.5
Dø ≥ 20 Dø + 1
13.0
16.0
7.5
18.0
22.0
10.0
0.8
79
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
6.3 (8)
SIZE
RIPPLE
ESR
10 (13)
SIZE
RIPPLE
ESR
470
680
820
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
8 x 11
8 x 11
1036
1036
43
RIPPLE
ESR
8 x 11
1036
43
8 x 15
1355
34
10 x 12
1400
31
43
1000
8 x 15
1355
34
8 x 20
1700
25
10 x 12
1400
31
10 x 15
1818
23
10 x 19.5
2318
16
10 x 25
2546
14
1200
8 x 15
1355
34
1500
8 x 20
1740
25
8 x 20
1700
25
10 x 12
1400
31
10 x 15
1818
23
1800
10 x 15
1818
23
10 x 19.5
2318
16
2200
10 x 19.5
2318
15
10 x 25
2545
14
3300
10 x 25
2364
14
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (mΩ Max.)
16 (20)
SIZE
Yageo corporation ELECTROLYTIC CAPACITORS
Miniature Aluminum
Electrolytic Capacitors
ST [ Low Impedance and Long Life ]
105°C 4000 ~ 10000 Hours, Low Impedance and Long Life
Electrical Characteristics
Operating Temperature Range : -40 ~ +105°C
Rated Voltage Range : 6.3 ~ 63V
Rated Capacitance Range : 6.8 ~ 15000μF
Capacitance Tolerance : ±20% at 120Hz, 20°C
description
Leakage Current (Max.) (20°C): I = 0.01CV or 3μA whichever is greater. (After Rated Voltage Applied for 2
Applicable for SMPS, Adaptor, Charger, Monitor/
Computer
Dissipation Factor (Max.) (tanδ) (120Hz, 20°C)
Minutes) I = Leakage Current (μA), C = Nominal Capacitance (μF), V = Rated Voltage (V)
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
W V (V) :
6.3
10
16
25
35
50
63
D.F. (%) :
22
19
16
14
12
10
9
When nominal capacitance is over 1000μF, tanδ shall be added 0.02 to the listed value with increase of
every 1000μF.
FREQUENCY (Hz)
120
1K
10K
100K
6.8~180μF
0.40
0.75
0.90
1.00
Low Temperature Stability Impedance Ratio (Max.)
220~560μF
0.50
0.85
0.94
1.00
W V (V) :
680~1800μF
0.60
0.87
0.95
1.00
2200~3900μF
0.75
0.90
0.95
1.00
Z - 25°C / Z + 20°C :
Z - 40°C / Z + 20°C :
4700μF Higher
0.85
0.95
0.98
1.00
6.3
10
16
25
35
50
63
4
8
3
6
2
4
2
3
2
3
2
3
2
3
Endurance
VDC :
5ø~6.3ø
8ø~10ø
12.5ø~18ø
6.3~10 (V) :
4000hrs
6000hrs
8000hrs
16~100 (V) :
5000hrs
7000hrs
10000hrs
After the rated voltage has been applied at 105°C for 4000~10000 hours. The capacitors shall meet the
following requirements.
(a) Capacitance Change: Within ±25% of Initial Value
(b) Dissipation Factor: 200% or Less of Initial Specified Value
(c) Leakage Current: Initial Specified Value or Less
Shelf Life: After having been placed at 105°C without voltage applied for 1000 hours, the capacitors shall
meet the same requirements as load life.
diagram of dimensions
Dimensions: mm
Rubber End Seal
Vinyl Sleeve
dø
F±0.5
F
dø
5.0
1.5
0.5
6.3
8.0
Dø±0.5
F±0.5
Dø
13.0
Dø < 20 Dø + 0.5
Dø ≥ 20 Dø + 1
0.6
10.0
L
15Min.
4Min.
16.0
18.0
2.0
0.8
81
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
6.3 (8)
SIZE
RIPPLE
ESR
10 (13)
SIZE
RIPPLE
ESR
16 (20)
SIZE
RIPPLE
ESR
47
56
100
150
5 x 11
5 x 11
210
6.3 x 11
6.3 x 11
340
210
0.720
5 x 11
210
0.720
6.3 x 11
340
0.380
0.720
220
330
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
340
0.380
0.380
470
25 (32)
SIZE
RIPPLE
ESR
5 x 11
210
0.720
6.3 x 11
340
0.380
8 x 11
640
0.200
8 x 11
640
0.200
8 x 11
640
0.200
8 x 15
701
0.160
8 x 15
840
0.160
8 x 11
640
0.200
8 x 15
840
0.160
10 x 15
1210
0.084
8 x 15
840
0.160
10 x 15
1210
0.084
10 x 19.5
1400
0.062
680
8 x 11
640
0.200
820
8 x 15
840
0.160
1000
10 x 12
865
0.120
10 x 15
1210
0.084
10 x 19.5
1400
0.062
13 x 20
1900
0.046
1500
8 x 20
1050
0.110
10 x 19.5
1400
0.062
10 x 25
1650
0.052
13 x 25
2230
0.034
10 x 15
1210
0.084
2200
10 x 19.5 1400
0.062
10 x 25
1650
0.052
13 x 25
2230
0.034
13 x 35
2880
0.027
2700
10 x 25
1650
0.052
13 x 20
1900
0.046
13 x 30
2650
0.030
16 x 25
2930
0.028
3300
13 x 20
1900
0.046
13 x 25
2230
0.034
13 x 35
2880
0.027
16 x 32
3450
0.025
3900
13 x 25
2230
0.034
13 x 30
2650
0.030
13 x 40
3350
0.024
18 x 32
4170
0.015
4700
13 x 30
2650
0.030
13 x 35
2880
0.027
16 x 25
3450
0.028
18 x 36
4280
0.014
5600
13 x 35
2880
0.027
13 x 40
3550
0.024
16 x 36
3610
0.018
16 x 25
2930
0.028
18 x 32
4170
0.015
16 x 32
3450
0.025
18 x 36
4220
0.014
6800
13 x 40
3350
0.024
16 x 25
2930
0.028
8200
16 x 32
3450
0.025
16 x 36
3610
0.018
10000
16 x 36
3610
0.018
18 x 36
4220
0.014
12000
18 x 32
4170
0.015
15000
18 x 36
4220
0.014
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω)
82
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
35 (44)
SIZE
RIPPLE
ESR
50 (63)
SIZE
RIPPLE
ESR
10
22
5 x 11
210
2.300
33
5 x 11
210
0.720
6.3 x 11
340
1.200
47
6.3 x 11
340
0.380
6.3 x 11
340
1.200
56
100
8 x 11
555
0.630
120
8 x 15
730
0.450
8 x 20
910
0.330
150
8 x 11
640
0.200
180
220
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
8 x 15
840
0.160
10 x 15
1050
0.310
270
63 (79)
SIZE
RIPPLE
ESR
5 x 11
55
2.300
6.3 x 11
115
1.200
8 x 11
232
0.630
10 x 15
357
0.310
10 x 19.5
466
0.210
10 x 25
531
0.200
10 x 30
663
0.150
13 x 20
690
0.160
330
10 x 19.5
1400
0.062
10 x 19.5
1400
0.210
13 x 25
784
0.120
470
10 x 25
1650
0.052
10 x 30
1690
0.150
13 x 30
905
0.100
13 x 20
1660
0.160
13 x 25
1950
0.120
13 x 35
1050
0.083
13 x 30
2310
0.100
13 x 40
1180
0.071
560
680
10 x 30
1910
0.044
13 x 20
1900
0.046
820
13 x 25
2230
0.034
13 x 35
2510
0.083
16 x 32
1570
0.054
1000
13 x 25
2230
0.034
16 x 25
2555
0.073
16 x 36
1790
0.045
1200
13 x 30
2650
0.030
16 x 32
3010
0.054
16 x 40
2020
0.040
1500
13 x 35
2880
0.027
16 x 36
3150
0.045
1800
13 x 40
3350
0.024
18 x 32
3635
0.047
2200
16 x 32
3450
0.025
18 x 36
3680
0.040
2700
16 x 36
3610
0.018
18 x 40
3800
0.036
3300
18 x 36
4220
0.014
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω)
Yageo corporation ELECTROLYTIC CAPACITORS
SD [ For High Ripple Current ]
Miniature Aluminum
Electrolytic Capacitors
105°C 5000 Hours, Long Life
Electrical Characteristics
Operating Temperature Range : -25 ~ +105°C
Rated Voltage Range : 160 ~ 450V
Rated Capacitance Range : 22 ~ 330μF
Capacitance Tolerance : ±20% at 120Hz, 20°C
Leakage Current (Max.) (20°C): I ≤ 0.02CV+15μA whichever is greater.
description
(After Rated Voltage Applied for 5 Minutes)
I = Leakage Current (μA), C = Nominal Capacitance (μF), V = Rated Voltage (V)
Applicable for used in super thin TV, with high ripple
current capability.
Dissipation Factor (Max.) (tanδ) (120Hz, 20°C)
W V (V) :
160
200
250
400
420
450
D.F. (%) :
18
18
18
20
22
24
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
Temperature Characteristics (Max.) (tanδ) (120Hz, 20°C)
W V (V) :
Z-25°C/Z+20°C :
160
200
250
400
420
450
4
4
5
6
6
6
FREQUENCY (Hz) 60
COEFFICIENT
120 300 1K
10K 100K≤
0.75 1.00 1.25 1.35 1.50 1.50
Endurance:
After the rated voltage and rated ripple current have been applied at 105°C for 5000 hours, the capacitors
shall meet the following requirements.
(a) Capacitance Change : Within ±20% of Initial Value
(b) issipation Factor: ≤ 2 Times of the Initial Specified Value
(c) Leakage Current: ≤ The Initial Specified Value
Shelf Life: After leaving capacitors under no load at 105°C for 1000 hours.
(a) Capacitance Change : Within ±20% of Initial Value
(b) Dissipation Factor: ≤ 2 Times of the Initial Specified Value
(c) Leakage Current: ≤ 2 Times of the Initial Specified Value
diagram of dimensions
Dimensions: mm
Safety Vent
Sleeve
F
dø
Max
8.0
3.5
0.6
2.0
10.0
5.0
F±0.5
Dø+0.5
Dø
L
Dø = 8 & 10, L + 2.5 Max.
12.5
Dø+0.5
Dø < 20 Dø + 0.5
Dø ≥ 20 Dø + 1
Dø+0.5
dø
84
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
160 (200)
SIZE
RIPPLE
200 (250)
SIZE
RIPPLE
250 (300)
SIZE
RIPPLE
400 (420)
SIZE
RIPPLE
420 (450)
SIZE
RIPPLE
450 (500)
SIZE
RIPPLE
22
8 x 45
225
8 x 50
235
8 x 50
255
27
8 x 50
265
10 x 40
265
10 x 45
285
33
8 x 40
225
10 x 40
300
10 x 45
305
10 x 50
320
39
8 x 45
245
10 x 45
330
10 x 50
350
12.5 x 40
380
47
8 x 50
305
12.5 x 35
400
12.5 x 40
420
12.5 x 45
450
56
8 x 35
260
8 x 45
285
10 x 40
335
12.5 x 40
470
12.5 x 45
480
12.5 x 50
500
68
8 x 40
335
8 x 50
350
10 x 45
380
12.5 x 45
530
12.5 x 50
560
12.5 x 55
585
82
8 x 45
390
10 x 40
460
10 x 50
440
12.5 x 50
610
12.5 x 55
625
12.5 x 60
635
100
8 x 50
470
10 x 45
490
12.5 x 45
530
12.5 x 55
715
12.5 x 60
730
120
10 x 40
520
10 x 50
570
12.5 x 50
600
150
10 x 50
650
12.5 x 45
710
12.5 x 55
735
180
12.5 x 40
745
12.5 x 50
785
12.5 x 60
830
220
12.5 x 45
830
12.5 x 55
880
270
12.5 x 50
960
12.5 x 60
1030
330
12.5 x 55
1100
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
Yageo corporation ELECTROLYTIC CAPACITORS
SL [ Long Life and Low Impedance ]
Miniature Aluminum
Electrolytic Capacitors
105°C 3000 ~ 7000 Hours, High Ripple Current and Long Life
Electrical Characteristics
Operating Temperature Range: -40 ~ +105°C / -25 ~ +105°C
Rated Voltage Range: 6.3 ~ 100V / 160 ~ 450V
Rated Capacitance Range: 2.2 ~ 18000uF
Capacitance Tolerance: ±20% at 120Hz, 20°C
Leakage Current (Max.) (20°C): I = 0.01CV or 3μA whichever is greater.
(After Rated Voltage Applied for 2 Minutes)
CV ≤ 1000: I = 0.1CV+40μA (max.), CV > 1000: I = 0.04CV+100μA (max.) (After 1 minute)
description
Excellent Ripple Current Capability
Dissipation Factor (Max.) (tanδ) (120Hz, 20°C)
W V (V) :
6.3
10
16
25
35
50
63
100
160~250
40~450
D.F. (%) :
22
19
16
14
12
10
9
8
20
24
When nominal capacitance exceeds 1000μF, add 0.02 to the value above for each 1000μF increase.
Temperature Characteristics (Impedance Ratio at 120Hz)
W V (V) :
6.3
10
16
25
35
50
63
100
160~250
400
450
Z-25°C/Z+20°C :
4
3
3
3
3
3
2
2
3
5
6
Z-40°C/Z+20°C :
8
6
4
4
3
3
3
3
Endurance: After the rated voltage has been applied at 105°C and then has resumed its original condition
for 16 hours.
Dø :
Load Life :
6.3ø
8ø
10ø
12.5ø
3000hrs
4000hrs
5000hrs
7000hrs
Used in communication equipment, switching power
supplies, industrial measuring.
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz)
120
1K
10K
100K
~180μF
0.40
0.75
0.90
1.00
220~560μF
0.50
0.85
0.94
1.00
680~1800μF
0.60
0.87
0.95
1.00
2200~3900μF
0.75
0.90
0.95
1.00
4700~18000μF
0.85
0.95
0.98
1.00
(a) Capacitance Change: ±25% of the Initial Measured Value
(b) Dissipation Factor: ≤ The Initial Specified Value
(c) Leakage Current: ≤ 2 Times of the Initial Specified Value
Shelf Life: After having been stored at 105°C for 1000 hours, and then has resumed its original condition for
16 hours.
(a) Capacitance Change: ±25% of the Initial Measured Value
(b) Dissipation Factor: ≤ The Initial Specified Value
(c) Leakage Current: ≤ 2 Times of the Initial Specified Value
diagram of dimensions
F
dø
6.3
2.5
0.5
8.0
3.5
0.6
10.0
5.0
Rubber End Seal
Vinyl Sleeve
dø
Dø±0.5
Dø
Dimensions: mm
F±0.5
12.5
16.0
18.0
7.5
0.8
L
15Min.
4Min.
Dø < 20 Dø + 0.5
Dø ≥ 20 Dø + 1
F±0.5
86
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
6.3 (8)
SIZE
16 (20)
SIZE
RIPPLE
ESR
100
6.3 x 11
298
0.286
120
6.3 x 11
298
0.286
RIPPLE
ESR
10 (13)
SIZE
RIPPLE
ESR
150
6.3 x 11
298
0.286
180
6.3 x 11
298
0.286
8 x 11
561
0.169
6.3 x 11
298
0.286
8 x 11
561
0.169
8 x 11
561
0.169
8 x 11
561
0.169
220
6.3 x 11
298
0.286
270
6.3 x 11
298
0.286
330
6.3 x 11
298
0.286
8 x 11
561
0.169
390
8 x 11
561
470
8 x 11
560
8 x 11
8 x 11
561
0.169
8 x 11
561
0.169
0.169
8 x 11
561
0.169
10 x 12
759
0.104
561
0.169
8 x 11
561
0.169
10 x 15
737
0.113
561
0.169
10 x 12
759
0.104
10 x 15
1061
0.078
8 x 15
737
0.113
8 x 20
921
0.090
10 x 12
759
0.104
10 x 15
1061
0.078
10 x 15
1061
0.078
10 x 19.5
1228
0.060
12.5 x 15
1272
0.064
680
820
1000
1200
1500
1800
2200
2700
3300
8 x 15
737
0.113
10 x 15
1061
0.078
10 x 15
1061
0.078
8 x 15
921
0.090
10 x 19.5
1228
0.060
12.5 x 15
1272
0.064
10 x 25
1447
0.055
8 x 20
921
0.090
10 x 19.5
1228
0.060
10 x 15
1061
0.078
10 x 25
1447
0.055
10 x 19.5
1228
0.060
10 x 25
1447
0.055
12.5 x 15
1272
0.064
16 x 15
1649
0.065
10 x 25
1447
0.055
10 x 30
1675
0.040
16 x 15
1570
0.072
10 x 19.5
1228
0.060
12.5 x 25
1863
0.039
16 x 15
1649
0.065
18 x 15
1687
0.073
16 x 20
1938
0.046
12.5 x 25
1863
0.039
16 x 20
1938
0.046
10 x 25
1447
0.055
16 x 15
1649
0.065
10 x 30
1675
0.040
12.5 x 25
1863
0.039
12.5 x 30
2214
0.034
16 x 15
1649
0.065
18 x 15
1772
0.066
16 x 20
1938
0.046
18 x 15
1772
0.066
12.5 x 30
2214
0.034
12.5 x 35
2406
0.029
16 x 20
1938
0.046
18 x 20
2188
0.044
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω)
87
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
3900
4700
5600
6800
8200
10000
6.3 (8)
SIZE
RIPPLE
ESR
10 (13)
SIZE
RIPPLE
ESR
16 (20)
SIZE
RIPPLE
ESR
12.5 x 25
1863
0.039
12.5 x 35
2406
0.029
16 x 25
2238
0.036
16 x 20
1938
0.046
18 x 20
2188
0.044
12.5 x 30
2214
0.034
12.5 x 40
2798
0.025
16 x 30
2657
0.029
16 x 20
1938
0.046
16 x 25
2238
0.036
18 x 25
2430
0.031
12.5 x 35
2406
0.029
16 x 25
2238
0.036
16 x 35
2740
0.026
16 x 20
1938
0.046
18 x 20
2188
0.044
18 x 30
3157
0.026
12.5 x 40
2798
0.025
16 x 30
2657
0.029
16 x 40
3408
0.022
16 x 30
2657
0.029
18 x 25
2430
0.031
18 x 25
2430
0.031
16 x 35
2740
0.026
16 x 35
2740
0.026
18 x 35
3191
0.025
18 x 30
3157
0.026
18 x 35
3191
0.025
18 x 40
3316
0.020
18 x 40
3316
0.020
16 x 35
2740
0.026
18 x 30
3157
0.026
16 x 40
3408
0.022
18 x 35
3191
0.025
15000
18 x 35
3191
0.025
18000
18 x 40
3316
0.020
12000
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω)
88
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
25 (32)
SIZE
50 (63)
SIZE
RIPPLE
ESR
33
6.3 x 11
259
0.390
39
6.3 x 11
259
0.390
RIPPLE
ESR
35 (44)
SIZE
RIPPLE
ESR
47
6.3 x 11
298
0.286
6.3 x 11
259
0.390
56
6.3 x 11
298
0.286
8 x 11
487
0.221
68
6.3 x 11
298
0.286
8 x 11
487
0.221
82
6.3 x 11
298
0.286
8 x 11
561
0.169
8 x 11
487
0.221
100
6.3 x 11
298
0.286
8 x 11
561
0.169
10 x 12
487
0.156
120
8 x 11
561
0.169
8 x 11
561
0.169
8 x 15
667
0.156
10 x 12
640
0.156
150
180
220
8 x 11
8 x 11
561
561
0.169
0.169
8 x 11
561
0.169
10 x 15
667
0.109
10 x 12
759
0.104
8 x 15
921
0.118
10 x 15
798
0.109
8 x 15
737
0.113
10 x 19.5
921
0.078
10 x 12
759
0.104
12 x 15
1070
0.079
270
10 x 12
759
0.104
10 x 15
1061
0.078
10 x 25
1105
0.072
330
8 x 15
737
0.113
8 x 20
921
0.090
10 x 30
1263
0.056
10 x 12
759
0.104
10 x 15
1061
0.078
10 x 15
1061
0.078
10 x 19.5
1228
0.060
16 x 15
1456
0.072
12 x 15
1272
0.064
10 x 19.5
1228
0.060
10 x 30
1482
0.056
12.5 x 25
1482
0.044
12.5 x 25
1710
0.044
18 x 15
1710
0.070
390
470
560
680
820
1000
1200
8 x 20
921
0.090
10 x 15
1061
0.078
10 x 19.5
1228
0.060
12.5 x 15
1272
0.064
10 x 19.5
1228
0.060
10 x 25
1447
0.055
10 x 25
1447
0.055
10 x 30
1482
0.056
12.5 x 30
1693
0.039
12.5 x 25
1863
0.039
16 x 20
2026
0.044
16 x 15
1570
0.072
12.5 x 25
1863
0.039
12.5 x 35
2201
0.033
18 x 15
1687
0.073
18 x 20
2184
0.047
10 x 30
1675
0.040
12.5 x 25
1920
0.046
12.5 x 35
2561
0.027
16 x 15
1570
0.072
16 x 20
1938
0.046
16 x 25
2241
0.033
12.5 x 25
1863
0.039
12.5 x 30
2214
0.034
16 x 30
2640
0.029
18 x 15
1687
0.073
16 x 20
1938
0.046
18 x 25
2403
0.034
89
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
1500
1800
2200
2700
3300
25 (32)
SIZE
RIPPLE
ESR
35 (44)
SIZE
RIPPLE
ESR
50 (63)
SIZE
RIPPLE
ESR
12.5 x 25
1863
0.039
12.5 x 35
2406
0.029
16 x 35
2763
0.025
16 x 20
1938
0.046
16 x 25
2238
0.036
12.5 x 30
2214
0.034
12.5 x 40
2798
0.025
18 x 30
3188
0.027
16 x 20
1938
0.046
16 x 25
2238
0.036
12.5 x 35
2406
0.029
16 x 30
2657
0.029
18 x 35
3228
0.022
18 x 20
2188
0.044
18 x 25
2430
0.031
16 x 25
2238
0.036
16 x 35
2740
0.026
18 x 40
3333
0.018
18 x 30
3157
0.026
18 x 35
3191
0.025
18 x 40
3316
0.020
16 x 30
2657
0.029
18 x 25
2430
0.031
16 x 35
2740
0.026
18 x 30
3157
0.026
4700
18 x 35
3191
0.025
5600
18 x 40
3316
0.020
3900
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω)
90
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
63 (79)
SIZE
RIPPLE
ESR
100 (125)
SIZE
RIPPLE
ESR
10
15
22
6.3 x 11
6.3 x 11
101
1.560
33
6.3 x 11
101
1.560
39
8 x 11
203
47
8 x 11
203
56
8 x 11
203
27
101
8 x 11
203
0.819
0.819
8 x 15
263
0.585
0.819
10 x 12
253
0.559
0.819
8 x 20
317
0.429
68
8 x 11
203
0.819
10 x 15
313
0.403
10 x 12
253
0.559
10 x 19.5
409
0.273
12.5 x 15
409
0.299
100
8 x 15
263
0.585
10 x 25
466
0.260
10 x 12
253
0.559
10 x 15
313
0.403
10 x 30
581
0.195
150
8 x 20
317
0.429
16 x 15
697
0.182
180
10 x 19.5
409
0.273
12.5 x 25
688
0.156
12.5 x 15
409
0.299
18 x 15
807
0.156
220
10 x 19.5
409
0.273
12.5 x 30
794
0.130
10 x 25
466
0.260
16 x 20
912
0.118
16 x 15
697
0.182
12.5 x 35
921
0.108
16 x 25
1096
0.095
12.5 x 40
1035
0.092
18 x 20
1088
0.104
270
330
390
470
10 x 30
581
0.195
12.5 x 25
688
0.156
16 x 30
1377
0.070
18 x 15
807
0.156
18 x 25
1307
0.074
12.5 x 30
794
0.130
16 x 32
1570
0.059
16 x 20
912
0.118
18 x 30
1430
0.061
560
16 x 25
1096
0.095
18 x 36
1570
0.052
680
12.5 x 35
921
0.108
18 x 36
1570
0.052
16 x 25
1096
0.095
18 x 20
1088
0.104
12.5 x 40
1035
0.092
18 x 40
2044
0.047
16 x 30
1377
0.070
18 x 25
1307
0.074
16 x 30
1377
0.070
16 x 35
1570
0.059
16 x 40
1772
0.052
18 x 30
1430
0.061
1500
18 x 35
1570
0.052
1800
18 x 40
2044
0.047
820
1000
1200
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω)
160 (200)
SIZE
RIPPLE
ESR
10 x 15
219
2.925
10 x 19.5.5
307
1.950
12.5 x 25
526
0.897
16 x 25
798
0.455
18 x 35
1202
0.273
1.560
82
120
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
91
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
200 (250)
SIZE
RIPPLE
ESR
250 (300)
SIZE
RIPPLE
ESR
400 (450)
SIZE
RIPPLE
ESR
2.2
3.3
4.7
10 x 19.5
171
5.460
10 x 15
145
6.285
10 x 25
193
4.485
450 (500)
SIZE
RIPPLE
ESR
10 x 15
96
10.270
10 x 19.5
118
8.060
10
10 x 15
219
2.925
10 x 19.5
202
5.200
12.5 x 25
316
2.340
12.5 x 25
228
3.380
22
10 x 19.5 307
1.950
12.5 x 25
316
2.340
16 x 25
500
1.586
16 x 30
421
1.300
12.5 x 25
316
2.340
16 x 30
614
0.897
18 x 35
579
0.806
18 x 30
754
0.650
33
47
12.5 x 25 526
0.897
16 x 25
500
1.105
100
16 x 30
1017
0.468
18 x 35
820
0.585
220
18 x 35
1202
0.234
18 x 40
877
0.520
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω)
Yageo corporation ELECTROLYTIC CAPACITORS
Miniature Aluminum
Electrolytic Capacitors
SU [ For Higher Temperature Range ]
125°C 2000 Hours, High Temperature
Electrical Characteristics
Operating Temperature Range : -40 ~ +125°C
Rated Voltage Range : 10 ~ 63VDC
Rated Capacitance Range : 4.7 ~ 4700μF
Capacitance Tolerance : ±20% at 120Hz, 20°C
description
Leakage Current (Max.) (20°C): I = 0.01CV or 3μA whichever is greater.
Applicable for Electronic Ballast, Lighting Ballast
I = Leakage Current (μA), C = Nominal Capacitance (μF), V = Rated Voltage (V)
(After Rated Voltage Applied for 2 Minutes)
Dissipation Factor (Max.) (tanδ) (120Hz, 20°C)
MULTIPLIER FOR RIPPLE CURRENT
W V (V) :
10
16
25
35
50
63
FREQUENCY (Hz)
120 1K
D.F. (%) :
0.20
0.16
0.14
0.12
0.10
0.09
Cap ≤ 10μF
1.00 1.45 1.65 1.70
When nominal capacitance is over 1000μF, the value of tanδ shall be increased by 0.02 for every addition of
10μF < Cap ≤ 100μF
1.00 1.36 1.48 1.53
1000μF.
10K 50K~100K
100μF < Cap ≤ 1,000μF 1.00 1.25 1.35 1.38
1,000μF < Cap
1.00 1.17 1.25 1.28
Low Temperature Stability Impedance Ratio (Max.)
W V (V) :
10
16
25
35
50
63
Z-25°C/Z+20°C :
3
2
2
2
2
2
Z-25°C/Z+20°C :
6
4
4
4
4
4
Endurance: After the rated voltage and rated ripple current have been applied at 125°C for 2000 hours, the
capacitors shall meet the following requirements.
(a) Capacitance Change: Within ±30% of Initial Value
(b) Dissipation Factor: 300% or Less of Initial Specified Value
(c) Leakage Current: Initial Specified Value or Less
Shelf Life: After leaving capacitors under no load at 125°C for 1000 hours.
(a) Capacitance Change: Within ±30% of Initial Value
(b) Dissipation Factor: 300% or Less of Initial Specified Value
(c) Leakage Current: 500% or Less of Initial Specified Value
diagram of dimensions
Dimensions: mm
Rubber End Seal
Vinyl Sleeve
F±0.5
F±0.5
Dø±0.5
dø
Dø
F
dø
5.0
1.5
0.5
6.3
8.0
0.6
10.0
L
Dø < 20 Dø + 0.5
Dø ≥ 20 Dø + 1
15Min.
4Min.
13.0
16.0
2.0
0.8
93
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
10 (13)
SIZE
RIPPLE
16 (20)
SIZE
RIPPLE
25 (32)
SIZE
RIPPLE
35 (44)
SIZE
RIPPLE
50 (63)
SIZE
RIPPLE
4.7
10
22
33
47
63 (79)
SIZE
RIPPLE
5 x 11
92
5 x 11
92
6.3 x 11
145
5 x 11
92
6.3 x 11
145
8 x 11
210
5 x 11
92
6.3 x 11
145
8 x 11
210
10 x 12
300
5 x 11
92
6.3 x 11
145
8 x 11
210
10 x 12
300
10 x 15
410
100
5 x 11
92
6.3 x 11
145
8 x 11
210
10 x 12
300
10 x 15
410
10 x 19.5
510
150
6.3 x 11
145
8 x 11
210
10 x 12
300
10 x 15
410
10 x 19.5
510
13 x 20
740
220
8 x 11
210
10 x 12
300
10 x 15
410
10 x 19.5
510
13 x 20
740
13 x 25
1070
330
10 x 12
300
10 x 15
410
10 x 19.5
510
13 x 20
740
13 x 25
1070
16 x 25
1100
470
10 x 15
410
10 x 19.5
510
13 x 20
740
16 x 25
1100
16 x 25
1100
16 x 32
1200
1000
10 x 19.5
510
13 x 20
740
16 x 25
1100
16 x 32
1200
16 x 32
1200
2200
13 x 25
1070
16 x 25
1100
16 x 32
1200
3000
16 x 25
1100
16 x 32
1200
4700
16 x 32
1200
Note: 1. Ripple Current: (mA/rms) 125°C, 120KHz
Yageo corporation ELECTROLYTIC CAPACITORS
Miniature Aluminum
Electrolytic Capacitors
SW [ Higher Temperature Range and Long Life ]
125°C 2000 ~ 5000 Hours, High Temperature Long Life
Electrical Characteristics
Operating Temperature Range : -40 ~ +125°C
Rated Voltage Range : 10 ~ 63VDC
Rated Capacitance Range : 47 ~ 4700μF
Capacitance Tolerance : ±20% at 120Hz, 20°C
description
Leakage Current (Max.) (20°C): I = 0.01CV or 3μA whichever is greater.
Applicable for Electronic Ballast, Lighting Ballast
I = Leakage Current (μA), C = Nominal Capacitance (μF), V = Rated Voltage (V)
(After Rated Voltage Applied for 2 Minutes)
Dissipation Factor (Max.) (tanδ) (120Hz, 20°C)
W V (V) :
10
16
25
35
50
63
10K
100K
D.F. (%) :
20
16
14
12
10
9
0.40 0.75
0.90
1.00
When nominal capacitance is over 1000μF, the value of tanδ shall be increased by 0.02 for every addition of
10μF < Cap ≤ 100μF
0.50 0.85
0.95
1.00
1000μF.
100μF < Cap ≤ 1,000μF
0.60 0.88
0.96
1.00
Low Temperature Stability Impedance Ratio (Max.)
1,000μF < Cap
0.75 0.90
0.98
1.00
W V (V) :
10
Z-25°C/Z+20°C :
3
2
2
2
2
2
Z-40°C/Z+20°C :
6
4
4
4
4
3
MULTIPLIER FOR RIPPLE CURRENT
FREQUENCY (Hz)
120
Cap ≤ 10μF
1K
16
25
35
50
63
Endurance: After the rated voltage and rated ripple current have been applied at 125°C for 2000~5000
hours, the capacitors shall meet the following requirements.
Dø :
8ø
10ø
≥13ø
Load Life :
2000hrs
3000hrs
5000hrs
(a) Capacitance Change: Within ±30% of Initial Value
(b) Dissipation Factor: 300% or Less of Initial Specified Value
(c) Leakage Current: Initial Specified Value or Less
Shelf Life: After leaving capacitors under no load at 125°C for 1000 hours.
(a) Capacitance Change: Within ±30% of Initial Value
(b) Dissipation Factor: 300% or Less of Initial Specified Value
(c) Leakage Current: 500% or Less of Initial Specified Value
diagram of dimensions
Dimensions: mm
Rubber End Seal
Vinyl Sleeve
F±0.5
F±0.5
Dø±0.5
dø
Dø
F
dø
8.0
1.5
0.6
10.0
13.0
L
Dø < 20 Dø + 0.5
Dø ≥ 20 Dø + 1
15Min.
4Min.
16.0
18.0
2.0
0.8
95
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
10 (13)
SIZE
RIPPLE
ESR
16 (20)
SIZE
RIPPLE
ESR
100
25 (32)
SIZE
RIPPLE
ESR
35 (44)
SIZE
RIPPLE
ESR
8 x 11
340
0.200
10 x 12
340
0.140
220
8 x 11
340
0.200
8 x 11
340
0.200
10 x 12
500
0.140
10 x 15
500
0.090
330
10 x 12
500
0.140
10 x 12
500
0.140
10 x 15
630
0.090
10 x 19
770
0.070
470
10 x 15
630
0.090
10 x 19
770
0.070
10 x 19
770
0.070
13 x 20
920
0.042
1000
10 x 19
770
0.070
13 x 20
920
0.042
13 x 25
1250
0.038
16 x 25
1380
0.028
2200
13 x 25
1250
0.038
16 x 25
1380
0.028
16 x 32
1450
0.025
3300
16 x 25
1380
0.028
16 x 32
1450
0.025
4700
16 x 32
1450
0.025
18 x 32
1720
0.018
Note: 1. Ripple Current: (mA/rms) 125°C, 100KHz
2. ESR: 100KHz / 20°C (Ω)
96
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
50 (63)
SIZE
RIPPLE
ESR
63(79)
SIZE
RIPPLE
ESR
47
8 x 11
245
0.680
8 x 11
245
0.068
100
10 x 12
415
0.360
10 x 15
455
0.300
220
10 x 19
491
0.180
13 x 20
665
0.120
330
13 x 20
665
0.120
13 x 25
995
0.100
470
13 x 25
995
0.100
16 x 25
1000
0.084
1000
16 x 32
1280
0.078
Note: 1. Ripple Current: (mA/rms) 125°C, 100KHz
2. ESR: 100KHz / 20°C (Ω)
Yageo corporation ELECTROLYTIC CAPACITORS
LH [ For Miniature ]
Large Can Aluminum
Electrolytic Capacitors
For Printed Circuit Board High-Performance Aluminum Electrolytic Power Supply
Input and Output Filter Capacitors
ELECTRICAL CHARACTERISTICS
Operating Temperature Range -40 to +85°C
-25 to +85°C
Rated Voltage Range
6.3 ~ 100V
160 to 450VDC
Rated Capacitance
820 ~ 120000μF
56 ~ 2200μF
Capacitance Tolerance
±20% at 120Hz, 20°C
Leakage Current
I = 0.02CV or 3mA Whichever is smaller.
(After 5 Minutes Application of DC Working Voltage at 20°C)
Description
Dissipation Factor (tanδ)
Rate Voltage (V) 6.3 10 16 25 35 50 63-100 160-400 450-500
Low Temperature Stability
Measurement frequency: 120Hz
Impedance Ratio (Max.)
Rate Voltage (V)
D.F. (%)
Endurance
60 55 55 45 35 30
6.3~16 25
25
15
Endurance : 85°C, 2000 Hours
20
35
50~63
Z(-25°C) / Z(20°C)
3
3
3
2
80~10 160~400 450
2
4
8
Z(-40°C) / Z(20°C)
12
10
8
6
5
-
-
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
After the rated voltage and rated ripple current have been applied at 85°C
FREQUENCY (Hz)
50
for 2000 hours, the capacitors shall meet the following requirements.
6.3~100V
0.88 0.90 1.00 1.15 1.16
(a) Capacitance Change: Within 20% of the Initial Value
160~250V
0.75 0.78 1.00 1.16 1.23
350~450V
0.74 0.76 1.00 1.10 1.15
500V
0.72 0.74 1.00 1.05 1.10
(b) Dissipation Factor: 200% or Less of Initial Specified Value
(c) Leakage Current: Initial Specified Value or Less
Shelf Life
Ideally sutiable for using in switching power supplies
and other industrial / commerical applications
60
120 1K
10K
After having been placed at 85°C without voltage applied for 1000 hours,
the capacitors shall meet the same requirements as Endurance.
diagram of dimensions
Unit: mm
Location of P.C.B. Holes
Vinyl Sleeve
10±0.5
0.9±0.1
10±0.5
Botton Plate
Negative
L+2 Max.
5.81
D±1
3.0
Safety Device
5.8±1.0
2mm x 2
1.5+0.2/-0.1
0.8+0.2/-0.1
98
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
6.3 (8)
SIZE
25 (32)
SIZE
RIPPLE
5600
22 x 25
2.20
6800
22 x 30
2.40
25 x 25
2.45
22 x 35
2.70
25 x 25
2.75
RIPPLE
10 (13)
SIZE
RIPPLE
8200
22 x 25
10000
12000
15000
18000
22000
27000
33000
16 (20)
SIZE
22 x 25
22 x 25
2.44
2.40
RIPPLE
2.60
22 x 30
2.70
22 x 40
3.10
25 x 25
2.75
25 x 30
3.15
30 x 25
3.20
22 x 30
2.90
22 x 45
3.50
25 x 25
2.95
25 x 35
3.45
30 x 30
3.50
35 x 25
3.55
22 x 30
2.75
22 x 35
3.30
22 x 50
4.00
25 x 25
2.75
25 x 30
3.45
25 x 40
3.95
30 x 25
3.50
30 x 35
4.00
35 x 30
4.05
22 x 30
2.60
22 x 35
3.15
22 x 40
3.70
25 x 45
4.45
25 x 25
2.62
25 x 25
3.05
25 x 35
3.75
30 x 35
4.45
30 x 30
3.80
35 x 30
4.60
22 x 30
3.06
22 x 40
3.55
22 x 50
4.35
30 x 40
5.20
25 x 25
3.07
25 x 30
3.50
25 x 40
4.30
35 x 35
5.15
30 x 25
3.55
30 x 30
4.25
30 x 45
5.95
35 x 25
4.20
35 x 40
5.90
22 x 35
3.49
22 x 45
4.05
25 x 45
4.70
30 x 50
6.70
25 x 30
3.52
25 x 35
4.00
30 x 35
4.65
35 x 45
6.75
30 x 25
3.57
30 x 30
4.05
35 x 30
4.65
22 x 40
3.97
22 x 50
4.60
30 x 40
5.35
35 x 50
7.55
25 x 35
4.02
25 x 40
4.55
35 x 30
5.40
30 x 30
4.05
30 x 30
4.50
35 x 25
4.10
35 x 25
4.50
Note: 1. Ripple Current: (A/rms) 85°C, 120Hz
99
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
6.3 (8)
SIZE
RIPPLE
10 (13)
SIZE
RIPPLE
16 (20)
SIZE
RIPPLE
22 x 50
4.56
25 x 45
5.10
30 x 45
6.00
25 x 40
4.50
30 x 35
5.05
35 x 35
5.95
30 x 30
4.46
35 x 30
5.05
35 x 25
4.51
25 x 45
5.09
25 x 50
5.75
30 x 50
6.80
30 x 35
5.06
30 x 40
5.70
35 x 40
6.75
35 x 30
5.03
35 x 30
5.65
25 x 50
5.71
30 x 45
6.45
35 x 45
7.60
30 x 40
5.70
35 x 35
6.40
35 x 30
5.75
30 x 45
6.48
30 x 50
7.05
35 x 50
8.00
35 x 35
6.42
35 x 40
7.10
30 x 50
7.32
35 x 50
7.50
35 x 40
7.29
100000
35 x 45
8.31
120000
35 x 50
8.60
39000
47000
56000
68000
82000
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
Note: 1. Ripple Current: (A/rms) 85°C, 120Hz
25 (32)
SIZE
RIPPLE
100
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
35 (44)
SIZE
80 (100)
SIZE
RIPPLE
1200
22 x 25
1.65
1500
22 x 30
1.90
25 x 25
1.90
22 x 35
2.20
25 x 30
2.20
30 x 25
2.20
RIPPLE
50 (63)
SIZE
RIPPLE
1800
22 x 25
2200
22 x 25
2700
3300
3900
4700
5600
63 (79)
SIZE
22 x 25
2.20
1.90
RIPPLE
1.85
22 x 30
2.30
22 x 40
2.45
25 x 25
2.30
25 x 30
2.45
30 x 25
2.50
22 x 30
2.10
22 x 35
2.45
22 x 45
2.80
25 x 25
2.20
25 x 30
2.45
25 x 35
2.80
30 x 25
2.50
30 x 30
2.85
35 x 25
2.85
22 x 30
2.35
22 x 40
2.60
22 x 50
3.15
25 x 25
2.35
25 x 30
2.65
25 x 40
3.20
30 x 25
2.70
30 x 30
3.20
35 x 25
3.20
22 x 35
2.65
22 x 45
2.95
25 x 45
3.60
25 x 30
2.65
25 x 35
2.95
30 x 35
3.60
30 x 25
2.65
30 x 30
3.00
35 x 30
3.60
22 x 30
2.40
22 x 40
3.00
22 x 50
3.40
25 x 50
4.05
25 x 25
2.40
25 x 35
3.00
25 x 40
3.35
30 x 40
4.05
30 x 25
2.95
30 x 30
3.35
35 x 35
4.10
35 x 25
3.40
22 x 35
2.75
22 x 45
3.35
25 x 45
3.70
30 x 45
4.55
25 x 25
2.75
25 x 40
3.35
30 x 35
3.75
35 x 35
4.50
30 x 30
3.35
35 x 30
3.75
35 x 25
3.40
Note: 1. Ripple Current: (A/rms) 85°C, 120Hz
101
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
6800
8200
10000
12000
15000
18000
22000
27000
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
35 (44)
SIZE
RIPPLE
50 (63)
SIZE
RIPPLE
63 (79)
SIZE
RIPPLE
80 (100)
SIZE
RIPPLE
22 x 40
2.85
22 x 50
3.80
30 x 40
4.25
30 x 50
5.15
25 x 30
2.85
25 x 40
3.80
35 x 30
4.20
35 x 40
5.15
30 x 25
2.90
30 x 30
3.80
30 x 35
3.85
35 x 30
3.85
35 x 45
5.85
35 x 50
6.60
22 x 45
3.15
25 x 50
4.35
30 x 45
4.80
25 x 35
3.10
30 x 40
4.35
35 x 35
4.80
30 x 30
3.15
35 x 30
4.40
22 x 50
3.55
30 x 45
5.00
30 x 50
5.50
25 x 40
3.50
35 x 35
4.95
35 x 40
5.45
30 x 30
3.45
35 x 25
3.40
25 x 45
3.95
30 x 50
5.60
35 x 45
6.20
30 x 35
4.00
35 x 40
5.55
35 x 30
4.05
25 x 50
4.95
35 x 45
6.45
30 x 40
4.95
35 x 35
5.00
30 x 45
5.50
35 x 50
6.70
35 x 40
5.55
30 x 50
6.00
35 x 45
6.05
35 x 50
6.90
Note: 1. Ripple Current: (A/rms) 85°C, 120Hz
102
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
100 (125)
SIZE
180 (225)
SIZE
RIPPLE
200 (250)
SIZE
RIPPLE
180
22 x 20
1.00
22 x 25
0.95
220
22 x 25
1.10
22 x 25
1.10
22 x 25
1.25
22 x 25
1.25
25 x 20
1.25
22 x 30
1.25
25 x 25
1.25
RIPPLE
270
22 x 25
330
390
470
560
680
820
1000
160 (200)
SIZE
22 x 25
1.85
RIPPLE
1.15
22 x 25
1.40
22 x 25
1.40
22 x 25
1.45
25 x 20
1.35
22 x 30
1.40
22 x 30
1.45
25 x 25
1.40
25 x 25
1.45
22 x 30
1.55
22 x 30
1.60
22 x 30
1.60
25 x 25
1.55
25 x 25
1.60
25 x 25
1.55
30 x 25
1.50
22 x 30
1.75
22 x 35
1.80
22 x 35
1.80
25 x 25
1.75
25 x 30
1.80
25 x 30
1.80
30 x 25
1.70
30 x 25
1.80
30 x 25
1.80
22 x 30
1.95
22 x 35
2.00
22 x 40
2.00
25 x 30
1.95
22 x 40
2.00
25 x 35
2.00
30 x 25
1.90
25 x 30
1.95
30 x 25
2.00
30 x 25
2.00
22 x 40
2.20
22 x 45
2.25
22 x 45
2.35
25 x 30
2.20
25 x 35
2.20
25 x 35
2.30
30 x 25
2.15
30 x 30
2.20
30 x 30
2.30
35 x 25
2.20
35 x 25
2.30
22 x 45
2.50
22 x 50
2.55
25 x 40
2.60
25 x 35
2.55
25 x 40
2.55
25 x 45
2.60
30 x 30
2.50
30 x 30
2.60
30 x 30
2.60
35 x 25
2.50
30 x 35
2.60
30 x 35
2.60
35 x 25
2.60
35 x 30
2.60
22 x 30
2.10
22 x 50
2.85
25 x 45
2.85
25 x 45
3.00
25 x 25
2.10
25 x 40
2.80
30 x 35
2.85
25 x 50
3.00
30 x 35
2.80
35 x 30
2.90
30 x 35
3.05
35 x 25
2.80
30 x 40
3.05
35 x 30
3.00
Note: 1. Ripple Current: (A/rms) 85°C, 120Hz
103
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
1200
1500
1800
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
100 (125)
SIZE
RIPPLE
160 (200)
SIZE
RIPPLE
180 (225)
SIZE
RIPPLE
200 (250)
SIZE
RIPPLE
22 x 35
2.40
25 x 45
3.15
30 x 40
3.25
25 x 50
3.30
25 x 30
2.45
30 x 35
3.15
35 x 30
3.30
30 x 40
3.30
35 x 30
3.20
35 x 35
3.30
30 x 45
3.30
35 x 30
3.30
35 x 35
3.30
22 x 40
2.70
30 x 45
3.75
30 x 45
3.85
30 x 45
3.80
25 x 30
2.75
35 x 30
3.70
35 x 35
3.80
30 x 50
3.80
30 x 25
2.75
35 x 35
3.70
35 x 40
3.80
35 x 35
3.80
35 x 40
3.80
22 x 45
3.10
30 x 50
4.20
35 x 40
4.30
35 x 40
4.35
25 x 35
3.15
35 x 40
4.20
35 x 45
4.30
35 x 45
4.35
30 x 30
3.15
35 x 25
3.15
22 x 50
3.50
35 x 40
4.60
35 x 45
4.90
35 x 45
4.95
25 x 40
3.55
35 x 45
4.80
35 x 50
4.90
35 x 50
4.95
30 x 30
3.55
35 x 25
3.60
25 x 45
4.10
35 x 50
5.45
30 x 35
4.05
35 x 30
4.05
25 x 50
4.50
30 x 40
4.55
35 x 30
4.50
30 x 45
5.15
35 x 35
5.10
4700
35 x 40
5.75
5600
35 x 50
6.20
2200
2700
3300
3900
Note: 1. Ripple Current: (A/rms) 85°C, 120Hz
104
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
250 (300)
SIZE
RIPPLE
350 (400)
SIZE
RIPPLE
400 (450)
SIZE
RIPPLE
420 (470)
SIZE
RIPPLE
47
56
68
22 x 20
82
100
120
150
180
220
270
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
22 x 20
22 x 25
0.78
0.90
0.55
450 (500)
SIZE
RIPPLE
22 x 25
0.50
22 x 20
0.55
22 x 25
0.65
22 x 25
0.60
22 x 25
0.67
25 x 20
0.60
22 x 30
0.70
25 x 25
0.70
500 (550)
SIZE
RIPPLE
22 x 25
0.65
22 x 25
0.80
22 x 30
0.80
25 x 20
0.65
25 x 20
0.80
25 x 25
0.80
22 x 30
0.90
22 x 30
0.90
22 x 30
0.85
22 x 40
1.00
25 x 20
0.90
25 x 25
0.90
22 x 35
0.95
30 x 25
0.90
25 x 30
0.95
30 x 25
0.95
22 x 30
0.95
30 x 30
1.00
35 x 25
1.00
22 x 30
1.00
22 x 30
0.95
22 x 30
0.95
25 x 25
1.00
22 x 35
1.05
22 x 40
1.05
25 x 25
1.05
25 x 30
1.05
30 x 25
1.05
22 x 35
1.15
22 x 35
1.15
22 x 35
1.05
22 x 35
1.05
22 x 50
1.40
25 x 30
1.15
25 x 30
1.15
25 x 30
1.05
22 x 45
1.20
30 x 35
1.20
30 x 25
1.15
30 x 25
1.15
30 x 25
1.05
25 x 35
1.20
30 x 30
1.20
25 x 40
1.35
30 x 40
1.40
35 x 30
1.30
22 x 25
1.05
22 x 40
1.30
22 x 40
1.20
22 x 40
1.35
25 x 20
1.00
25 x 30
1.25
22 x 45
1.30
30 x 35
1.35
30 x 25
1.25
25 x 35
1.30
35 x 25
1.35
30 x 30
1.35
22 x 30
1.15
22 x 45
1.45
22 x 50
1.50
22 x 45
1.40
22 x 45
1.40
30 x 45
1.60
22 x 35
1.15
25 x 35
1.45
25 x 40
1.50
22 x 50
1.55
25 x 50
1.55
35 x 35
1.50
25 x 25
1.15
30 x 30
1.45
30 x 30
1.50
25 x 40
1.50
30 x 40
1.55
35 x 25
1.45
35 x 25
1.50
25 x 45
1.60
35 x 30
1.55
22 x 30
1.30
25 x 40
1.65
22 x 50
1.60
25 x 40
1.50
25 x 50
1.55
30 x 50
1.80
25 x 25
1.30
30 x 35
1.65
25 x 40
1.65
30 x 40
1.60
30 x 45
1.75
35 x 40
1.70
35 x 25
1.65
30 x 35
1.65
35 x 35
1.70
35 x 30
1.65
Note: 1. Ripple Current: (A/rms) 85°C, 120Hz
105
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
330
390
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
250 (300)
SIZE
RIPPLE
350 (400)
SIZE
RIPPLE
400 (450)
SIZE
RIPPLE
420 (470)
SIZE
RIPPLE
450 (500)
SIZE
RIPPLE
500 (550)
SIZE
RIPPLE
22 x 30
1.50
25 x 50
1.80
25 x 45
1.75
25 x 45
1.75
30 x 40
1.75
35 x 45
2.00
25 x 25
1.50
30 x 40
1.80
25 x 50
1.90
25 x 50
1.85
30 x 50
2.00
30 x 25
1.50
35 x 30
1.80
30 x 40
1.90
30 x 40
1.75
35 x 40
2.00
35 x 30
1.85
30 x 45
1.90
35 x 45
1.90
30 x 45
2.00
35 x 50
2.30
35 x 45
2.25
22 x 35
1.65
30 x 40
2.00
30 x 40
1.95
25 x 35
1.65
35 x 30
2.00
30 x 45
2.15
30 x 25
1.65
35 x 35
2.10
22 x 40
1.85
30 x 45
2.25
30 x 45
2.20
30 x 45
2.10
30 x 50
2.30
25 x 35
1.85
35 x 35
2.25
30 x 50
2.40
30 x 50
2.20
35 x 50
2.50
30 x 30
1.90
35 x 40
2.40
35 x 40
2.40
35 x 25
1.90
22 x 45
2.10
30 x 50
2.45
30 x 50
2.45
30 x 50
2.30
35 x 50
2.70
25 x 40
2.10
35 x 40
2.50
35 x 45
2.70
35 x 45
2.30
30 x 30
2.10
35 x 25
2.10
25 x 45
2.45
35 x 45
2.90
35 x 50
2.90
35 x 60
2.90
30 x 35
2.45
35 x 25
2.45
30 x 45
2.75
35 x 30
2.75
30 x 45
3.30
35 x 35
3.30
1200
35 x 40
3.55
1500
35 x 45
4.05
470
560
680
820
1000
Note: 1. Ripple Current: (A/rms) 85°C, 120Hz
Yageo corporation ELECTROLYTIC CAPACITORS
Large Can Aluminum
Electrolytic Capacitors
LG [ For General ]
For Printed Circuit Board High-Performance Aluminum Electrolytic Power Supply
Input and Output Filter Capacitors
ELECTRICAL CHARACTERISTICS
Operating Temperature Range -40 to +105°C
-25 to +105°C
Rated Voltage Range
6.3 to 100VDC
160 to 450VDC
Rated Capacitance Range
560 ~ 82000μF
47 ~ 2200μF
Capacitance Tolerance
±20% at 120Hz, 20°C
Leakage Current
I = 0.02CV, L = 20m/m, I = 0.03CV or 3mA whichever is smaller.
(After 5 Minutes Application of DC Working Voltage at 20°C)
Description
I = Leakage Current (μA), C = Nominal Capacitance (μF),V = Rated Voltage (V)
Endurance : 105°C 2000 hours, higher temperature
than LH.
Ideally suitable for using in switching power supplies
and other industrial / commercial applications.
Dissipation Factor (tanδ)
120 1K
10K
6.3
10
16
25
35
50
D.F. (%)
60
55
55
45
35
30
Low Temperature Stability
Measurement frequency: 120Hz
Impedance Ratio (Max.)
Rated Voltage (V)
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
60
Rate Voltage (V)
6.3~16 25
63-100 160-400 450
25
15
35
50~63
Z(-25°C) / Z(20°C)
4
3
3
2
80~10 160~400 450
2
4
8
Z(-40°C) / Z(20°C)
15
10
8
6
5
-
-
FREQUENCY (Hz)
50
6.3~100V
0.88 0.90 1.00 1.15 1.16
for 2000 hours, the capacitors shall meet the following requirements.
160~250V
0.85 0.88 1.00 1.15 1.20
315~450V
0.88 0.90 1.00 1.10 1.15
(a) Capacitance Change: ≤ ±20% of the Initial Value
(b) Dissipation Factor: ≤ 200% of the Initial Specified Value
Endurance
20
After the rated voltage and rated ripple current have been applied at 105°C
(c) Leakage Current: ≤ the Initial Specified Value
Shelf Life
After having been placed at 105°C without voltage applied for 1000 hours,
the capacitors shall meet the same requirements as Endurance.
diagram of dimensions
Unit: mm
Location of P.C.B. Holes
Vinyl Sleeve
10±0.5
0.9±0.1
10±0.5
3.0
5.8±1.0
2mm x 2
Botton Plate
1.5+0.2 /-0.1
Negative
0.8+0.2 /-0.1
Safety Device
L+2 Max.
5.8±0.1
D±1
107
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
Rated Voltage W V (SURGE VOLTAGE W V)
6.3 (8)
SIZE
25 (32)
SIZE
RIPPLE
4700
22 x 25
1.50
5600
22 x 30
1.65
25 x 25
1.65
RIPPLE
10 (13)
SIZE
RIPPLE
6800
22 x 25
8200
10000
12000
15000
18000
22000
27000
33000
39000
47000
56000
68000
82000
16 (20)
SIZE
22 x 25
1.55
RIPPLE
1.55
22 x 30
1.85
25 x 25
1.85
2.10
22 x 30
1.70
22 x 35
25 x 25
1.70
25 x 30
2.10
30 x 25
2.15
22 x 25
1.55
22 x 30
1.95
22 x 40
2.40
25 x 25
1.55
25 x 25
1.95
25 x 35
2.40
22 x 30
1.75
30 x 30
2.40
35 x 25
2.40
22 x 35
2.20
22 x 45
2.70
25 x 30
2.25
25 x 40
2.75
30 x 25
2.30
30 x 30
2.70
35 x 25
2.75
22 x 30
1.70
22 x 30
1.90
22 x 40
2.55
25 x 45
3.15
25 x 25
1.70
25 x 25
1.90
25 x 35
2.60
30 x 35
3.15
35 x 30
3.25
30 x 30
2.60
35 x 25
2.65
22 x 30
1.95
22 x 35
2.20
22 x 45
2.90
25 x 50
3.55
25 x 25
1.95
25 x 30
2.25
25 x 40
2.90
30 x 40
3.55
30 x 30
2.90
35 x 35
3.55
35 x 25
2.95
22 x 35
2.25
22 x 40
2.50
25 x 45
3.30
30 x 45
4.05
25 x 30
2.25
25 x 35
2.55
30 x 35
3.30
35 x 35
3.80
30 x 25
2.25
30 x 25
2.45
35 x 30
3.30
22 x 40
2.55
22 x 50
2.95
25 x 50
3.80
35 x 45
4.70
25 x 35
2.55
25 x 40
2.90
30 x 40
3.75
35 x 30
3.75
35 x 50
5.40
30 x 30
2.55
30 x 30
2.85
35 x 25
2.55
35 x 25
2.80
22 x 45
2.90
25 x 45
3.30
30 x 45
4.30
25 x 40
2.95
30 x 35
3.30
35 x 35
4.25
30 x 30
2.90
35 x 30
3.30
35 x 25
2.95
25 x 50
3.25
25 x 50
3.70
30 x 50
4.80
30 x 35
3.25
30 x 40
3.70
35 x 40
4.80
35 x 30
3.30
35 x 30
3.65
35 x 45
5.45
25 x 50
3.70
30 x 45
4.20
30 x 40
3.70
35 x 35
3.80
30 x 45
4.15
30 x 50
4.65
35 x 35
4.10
35 x 40
4.65
35 x 50
5.50
30 x 50
4.70
35 x 40
4.70
35 x 45
5.30
Note: 1. Ripple Current: (A/rms) 105°C, 120Hz
108
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
35 (44)
SIZE
80 (100)
SIZE
RIPPLE
820
22 x 25
1.10
1000
22 x 30
1.20
25 x 25
1.20
22 x 30
1.40
25 x 25
1.40
RIPPLE
50 (63)
SIZE
RIPPLE
1200
22 x 25
1500
1800
22 x 25
2200
2700
3300
3900
4700
63 (79)
SIZE
22 x 25
1.40
1.30
RIPPLE
1.20
22 x 30
1.30
22 x 35
1.60
25 x 25
1.30
25 x 30
1.60
30 x 25
1.65
22 x 30
1.50
22 x 40
1.80
25 x 25
1.50
25 x 35
1.85
30 x 25
1.80
22 x 30
1.55
22 x 35
1.70
22 x 45
2.05
25 x 25
1.55
25 x 30
1.75
25 x 35
2.00
30 x 25
1.80
30 x 30
2.05
35 x 25
2.05
22 x 30
1.70
22 x 40
2.00
25 x 45
2.35
25 x 25
1.70
25 x 35
2.00
30 x 35
2.35
30 x 25
1.95
35 x 30
2.35
22 x 35
1.95
22 x 50
2.30
25 x 50
2.70
25 x 30
1.85
25 x 40
2.30
30 x 40
2.70
30 x 30
2.25
35 x 30
2.55
35 x 25
2.10
22 x 30
1.55
22 x 40
2.15
25 x 45
2.55
30 x 45
3.00
25 x 25
1.55
25 x 35
2.20
30 x 35
2.55
35 x 35
3.00
30 x 25
1.95
35 x 30
2.55
22 x 35
1.80
22 x 45
2.45
25 x 50
2.85
30 x 50
3.40
25 x 25
1.80
25 x 40
2.45
30 x 40
2.85
35 x 40
3.40
30 x 30
2.45
35 x 30
2.80
35 x 25
2.50
Note: 1. Ripple Current: (A/rms) 105°C, 120Hz
109
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
5600
6800
35 (44)
SIZE
RIPPLE
50 (63)
SIZE
RIPPLE
63 (79)
SIZE
RIPPLE
80 (100)
SIZE
RIPPLE
22 x 35
19.5
22 x 50
2.75
30 x 45
3.20
35 x 45
3.80
25 x 30
1.95
25 x 40
2.70
35 x 35
3.20
30 x 25
2.00
30 x 35
2.75
35 x 30
2.75
35 x 50
3.90
35 x 60
4.00
22 x 40
2.20
25 x 50
3.30
30 x 50
3.65
25 x 35
2.25
30 x 40
3.30
35 x 40
3.65
30 x 30
2.30
35 x 30
3.25
35 x 25
2.35
22 x 50
2.55
30 x 45
3.60
35 x 45
3.90
25 x 40
2.50
35 x 35
3.55
30 x 30
2.75
35 x 25
2.75
25 x 45
2.85
30 x 50
4.05
35 x 50
4.40
30 x 35
2.90
35 x 50
4.05
35 x 30
2.95
35 x 40
4.00
25 x 50
3.25
35 x 45
4.55
30 x 40
3.25
35 x 30
3.15
30 x 45
3.70
35 x 35
3.65
18000
35 x 40
4.35
22000
35 x 50
4.90
8200
10000
12000
15000
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
Note: 1. Ripple Current: (A/rms) 105°C, 120Hz
110
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
100 (125)
SIZE
RIPPLE
160 (200)
SIZE
RIPPLE
180 (225)
SIZE
RIPPLE
150
180
220
22 x 20
270
22 x 25
330
390
470
560
680
820
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
22 x 25
22 x 25
1.05
1.20
0.80
1.00
200 (250)
SIZE
RIPPLE
22 x 20
0.65
22 x 20
0.75
22 x 20
0.70
22 x 25
0.85
22 x 25
0.80
25 x 20
0.80
22 x 25
0.95
22 x 25
0.85
25 x 20
0.90
25 x 25
0.85
22 x 25
1.20
22 x 25
1.20
22 x 30
1.20
25 x 20
1.15
22 x 30
1.10
25 x 25
1.20
25 x 25
1.10
22 x 30
1.30
22 x 30
1.30
22 x 30
1.30
25 x 25
1.30
25 x 25
1.30
22 x 35
1.30
25 x 30
1.30
30 x 25
1.30
22 x 30
1.30
22 x 30
1.30
22 x 35
1.40
22 x 35
1.40
22 x 35
1.35
22 x 40
1.40
25 x 25
1.40
25 x 30
1.40
25 x 30
1.40
30 x 25
1.40
30 x 25
1.50
22 x 40
1.50
22 x 40
1.50
22 x 45
1.55
25 x 30
1.50
25 x 35
1.55
25 x 35
1.55
30 x 25
1.50
30 x 25
1.50
30 x 30
1.55
22 x 45
1.70
22 x 45
1.70
22 x 50
1.75
25 x 35
1.70
22 x 50
1.70
25 x 40
1.75
30 x 25
1.70
25 x 35
1.70
30 x 30
1.75
25 x 40
1.75
35 x 25
1.70
30 x 30
1.70
35 x 25
1.70
22 x 30
1.30
22 x 50
1.95
22 x 50
1.95
25 x 50
2.05
25 x 25
1.33
25 x 40
2.00
25 x 40
2.00
30 x 35
2.00
30 x 30
2.00
25 x 45
2.00
35 x 30
2.05
35 x 25
1.90
30 x 35
2.00
35 x 25
1.90
Note: 1. Ripple Current: (A/rms) 105°C, 120Hz
111
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
1000
1200
1500
100 (125)
SIZE
RIPPLE
160 (200)
SIZE
RIPPLE
180 (225)
SIZE
RIPPLE
200 (250)
SIZE
RIPPLE
22 x 35
1.50
25 x 45
2.20
25 x 45
2.20
30 x 40
2.30
25 x 30
1.50
30 x 35
2.20
25 x 50
2.20
30 x 45
2.30
35 x 30
2.20
30 x 35
2.25
35 x 30
2.30
30 x 40
2.25
35 x 35
2.30
35 x 30
2.25
22 x 40
1.70
25 x 50
2.45
25 x 50
2.45
30 x 50
2.60
25 x 35
1.70
30 x 40
2.45
30 x 40
2.45
35 x 40
2.65
30 x 25
1.70
35 x 30
2.45
30 x 45
2.50
35 x 35
2.50
35 x 45
3.10
35 x 50
3.15
35 x 50
4.80
22 x 45
1.95
30 x 45
2.80
30 x 45
2.80
25 x 40
2.00
35 x 35
2.80
30 x 50
2.90
30 x 30
1.95
35 x 40
2.90
35 x 25
2.00
25 x 45
2.20
30 x 50
3.30
30 x 50
3.30
30 x 35
2.50
35 x 45
3.30
35 x 50
3.30
35 x 30
2.45
25 x 50
2.55
35 x 50
3.75
35 x 50
3.60
30 x 40
2.70
35 x 30
2.55
30 x 45
2.90
35 x 35
2.85
30 x 50
3.25
35 x 40
3.25
3900
35 x 45
3.70
4700
30 x 50
3.80
35 x 50
3.80
1800
2200
2700
3300
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
Note: 1. Ripple Current: (A/rms) 105°C, 120Hz
112
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
250 (300)
SIZE
RIPPLE
350 (400)
SIZE
RIPPLE
47
400 (450)
SIZE
RIPPLE
22 x 20
420 (470)
SIZE
450 (500)
SIZE
RIPPLE
0.35
22 x 25
0.38
RIPPLE
56
22 x 20
0.40
22 x 20
0.40
22 x 25
0.40
68
22 x 25
0.45
22 x 25
0.50
22 x 30
0.50
25 x 20
0.50
25 x 25
0.50
82
100
120
150
180
22 x 25
22 x 20
22 x 25
22 x 25
25 x 20
220
0.56
0.60
0.65
0.80
0.75
22 x 25
0.55
22 x 25
0.52
22 x 30
0.52
25 x 20
0.50
22 x 30
0.60
22 x 35
0.55
25 x 25
0.65
25 x 30
0.55
30 x 25
0.55
22 x 30
0.70
22 x 30
0.60
22 x 30
0.55
25 x 25
0.70
22 x 35
0.65
22 x 40
0.65
25 x 25
0.65
25 x 30
0.60
25 x 30
0.65
30 x 25
0.65
22 x 35
0.75
22 x 35
0.70
22 x 35
0.60
25 x 30
0.75
25 x 30
0.70
22 x 45
0.70
30 x 25
0.75
30 x 25
0.75
25 x 35
0.70
30 x 30
0.70
35 x 25
0.70
22 x 40
0.80
22 x 35
0.72
22 x 35
0.58
22 x 40
0.68
25 x 30
0.80
22 x 40
0.80
22 x 40
0.65
22 x 50
0.80
30 x 25
0.85
25 x 30
0.85
25 x 30
0.70
25 x 40
0.80
25 x 35
0.85
30 x 30
0.75
30 x 30
0.85
35 x 25
0.75
35 x 25
0.80
22 x 40
0.81
22 x 40
0.68
22 x 45
0.75
22 x 50
0.95
25 x 35
0.68
25 x 45
0.85
22 x 45
0.90
25 x 35
0.90
25 x 40
0.95
30 x 35
0.85
30 x 30
0.90
30 x 30
0.90
35 x 30
0.85
22 x 30
0.95
22 x 50
1.05
25 x 45
1.05
25 x 40
0.85
22 x 50
0.85
25 x 25
0.95
25 x 40
1.05
30 x 30
1.05
25 x 45
0.95
25 x 50
1.00
30 x 30
1.00
30 x 35
1.05
30 x 40
0.95
30 x 40
1.00
35 x 25
1.05
35 x 30
1.10
35 x 30
1.00
Note: 1. Ripple Current: (A/rms) 105°C, 120Hz
113
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
270
330
390
470
560
680
820
1000
1500
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
250 (300)
SIZE
RIPPLE
350 (400)
SIZE
RIPPLE
400 (450)
SIZE
RIPPLE
420 (470)
SIZE
RIPPLE
450 (500)
SIZE
RIPPLE
22 x 35
1.15
25 x 45
1.20
22 x 45
1.10
25 x 45
1.05
25 x 50
1.05
25 x 30
1.15
30 x 35
1.20
25 x 50
1.20
30 x 40
1.05
30 x 45
1.15
30 x 25
1.15
35 x 30
1.20
30 x 40
1.20
35 x 30
1.05
35 x 35
1.15
35 x 35
1.20
22 x 40
1.25
30 x 40
1.35
25 x 50
1.25
25 x 50
1.15
30 x 45
1.25
25 x 30
1.20
30 x 45
1.35
30 x 45
1.40
30 x 40
1.15
30 x 50
1.40
30 x 25
1.25
35 x 35
1.35
35 x 35
1.35
35 x 35
1.15
35 x 40
1.40
22 x 45
1.50
30 x 45
1.50
30 x 45
1.42
30 x 45
1.25
30 x 50
1.40
25 x 35
1.50
35 x 35
1.50
30 x 50
1.55
35 x 45
1.55
30 x 30
1.50
35 x 40
1.55
22 x 50
1.55
30 x 45
1.45
30 x 50
1.40
35 x 40
1.47
25 x 40
1.55
30 x 50
1.75
35 x 40
1.35
35 x 45
1.68
30 x 30
1.55
35 x 40
1.65
35 x 50
1.70
35 x 25
1.55
35 x 45
1.75
35 x 50
1.75
30 x 60
1.90
35 x 50
1.80
35 x 60
2.10
35 x 40
25 x 45
1.80
30 x 35
1.80
35 x 45
1.80
35 x 30
1.80
35 x 50
1.90
25 x 50
1.95
35 x 50
2.10
30 x 40
2.00
35 x 60
2.15
35 x 35
2.00
30 x 45
2.15
35 x 35
2.10
30 x 45
2.10
35 x 40
2.30
35 x 50
3.63
Note: 1. Ripple Current: (A/rms) 105°C, 120Hz
35 x 45
1.70
35 x 50
1.90
2.10
35 x 45
1.65
Yageo corporation ELECTROLYTIC CAPACITORS
Large Can Aluminum
Electrolytic Capacitors
LV [ For Long Life ]
For Printed Circuit Board High-Performance Aluminum Electrolytic Power
Supply Input and Output Filter Capacitors
ELECTRICAL CHARACTERISTICS
Operating Temperature Range -40 to +105°C
-25 to +105°C
Rated Voltage Range
10 to 100VDC
160 to 450VDC
Rated Capacitance Range
560 ~ 68000μF
270 ~ 2200μF
Capacitance Tolerance
±20% at 120Hz, 20°C
Leakage Current
1 ≤ 0.02CV or 3mA whichever is smaller
(After Rated Voltage Applied for 5 Minutes)
Description
I = Leakage Current (μA), C = Nominal Capacitance (μF),V = Rated Voltage (V)
Features : 105°C 3000 hours, Longer life than LG,
Snap-in terminal, High ripple current.
Dissipation Factor (tanδ)
Rate Voltage (V) 10 16 25 35 50 63 80 100 160 180~400 450
(20°C, 120Hz)
D.F (%)
Recommended Applications : Smoothing circuit, TV/
Monitor, Adapter, SMPS.
25
15
15
25
standard rating
Endurance
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
55 55 45 40 35 30 25
Dissipation Factor (tan δ) shall not exceed the values showed as above of
After the rated voltage has been applied at 105°C for 3000 hours, the
capacitors shall meet the following requirements.
FREQUENCY (Hz)
50
60
120
400
COEFFICIENT
0.8
0.85
1.0
1.14
FREQUENCY (Hz)
IK
2.4K
5K
10K
COEFFICIENT
1.23 1.3
1.36
1.4
(a) Capacitance Change : Within ±20% of the Initial Value
(b) Dissipation Factor : Not Exceeding 200% of the Specified Value
(c) Leakage current : Not Exceeding the Specified Value
Shelf Life
After having been placed at 105°C without voltage applied for 1000 hours,
the capacitors shall meet the same requirements as Endurance.
diagram of dimensions
Unit: mm
Location of P.C.B. Holes
Vinyl Sleeve
0.9±0.1
Botton Plate
10±0.5
3.0
5.8±1.0
2mm x 2
1.5+0.2/-0.1
10±0.5
Negative
0.8+0.2/-0.1
Safety Device
L+2 Max.
5.8±0.1
D±1
115
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
10 (13)
SIZE
RIPPLE
16 (20)
SIZE
RIPPLE
25 (32)
SIZE
RIPPLE
35 (44)
SIZE
RIPPLE
50 (63)
SIZE
RIPPLE
1200
1500
22 x 25
1800
22 x 30
2200
2700
22 x 25
3300
22 x 30
3900
22 x 25
4700
22 x 30
5600
6800
8200
22 x 25
1.80
1.50
1.80
22 x 30
1.45
1.60
1.80
1.25
1.45
RIPPLE
22 x 25
1.25
22 x 30
1.45
25 x 25
1.45
22 x 35
1.60
25 x 30
1.60
22 x 30
1.60
22 x 40
1.89
25 x 25
1.60
25 x 30
1.80
30 x 25
1.85
22 x 35
1.80
22 x 45
2.06
25 x 30
1.80
25 x 35
2.00
30 x 30
2.08
22 x 40
2.05
25 x 40
2.32
25 x 30
1.95
30 x 30
2.30
30 x 25
2.01
35 x 25
2.35
22 x 45
2.27
25 x 45
2.55
25 x 35
2.20
30 x 35
2.55
30 x 30
2.29
35 x 30
2.63
22 x 35
2.23
22 x 50
2.50
25 x 50
2.83
25 x 25
2.10
25 x 40
2.42
30 x 40
2.86
30 x 30
2.40
35 x 30
2.80
35 x 25
2.45
22 x 30
1.95
22 x 40
2.41
25 x 45
2.70
30 x 45
3.18
25 x 25
1.95
25 x 30
2.30
30 x 35
2.70
35 x 35
3.15
30 x 25
2.37
35 x 30
2.78
22 x 35
2.20
22 x 45
2.68
30 x 40
3.06
30 x 50
3.50
25 x 30
2.20
25 x 35
2.60
35 x 30
3.00
35 x 40
3.50
30 x 30
2.70
35 x 45
3.90
22 x 30
2.05
22 x 40
2.47
22 x 50
3.02
30 x 45
3.38
25 x 25
2.05
25 x 35
2.50
25 x 40
2.93
35 x 35
3.35
30 x 25
2.45
30 x 30
2.90
35 x 25
2.96
Note: 1. Ripple Current: (A/rms) 105°C, 120Hz
63 (79)
SIZE
116
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
10000
12000
15000
18000
22000
10 (13)
SIZE
RIPPLE
16 (20)
SIZE
RIPPLE
25 (32)
SIZE
RIPPLE
35 (44)
SIZE
RIPPLE
50 (63)
SIZE
RIPPLE
22 x 25
1.80
22 x 35
2.45
22 x 45
2.75
25 x 45
3.20
30 x 50
3.50
25 x 30
2.45
25 x 40
2.80
30 x 35
3.20
35 x 40
3.70
30 x 30
2.75
35 x 30
3.30
35 x 50
4.20
22 x 30
2.05
22 x 40
2.73
22 x 50
3.13
25 x 50
3.64
25 x 25
2.05
25 x 30
2.60
25 x 45
3.22
30 x 40
3.67
30 x 25
2.68
30 x 35
3.19
35 x 30
3.60
35 x 25
3.10
22 x 35
2.45
22 x 45
2.99
25 x 50
3.43
30 x 45
4.04
25 x 30
2.45
25 x 35
2.90
30 x 40
3.47
35 x 35
4.00
30 x 25
2.55
30 x 30
3.02
35 x 30
3.40
22 x 40
2.94
22 x 50
3.43
30 x 45
3.94
35 x 40
4.60
25 x 30
2.80
25 x 40
3.33
35 x 35
3.90
30 x 30
3.11
30 x 30
3.30
35 x 25
3.37
35 x 50
5.10
22 x 45
3.24
25 x 45
3.70
30 x 50
4.30
25 x 35
3.15
30 x 35
3.70
35 x 40
4.30
30 x 30
3.28
35 x 30
3.81
35 x 25
3.37
25 x 40
3.50
30 x 40
4.15
35 x 45
4.85
30 x 35
3.67
35 x 35
4.27
35 x 30
3.78
25 x 45
4.00
30 x 50
4.65
30 x 40
4.20
35 x 40
4.65
35 x 30
4.08
25 x 50
4.45
35 x 45
5.25
30 x 45
4.67
35 x 35
4.63
47000
35 x 40
4.90
35 x 50
5.80
56000
35 x 45
5.50
68000
35 x 50
6.05
27000
33000
39000
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
Note: 1. Ripple Current: (A/rms) 105°C, 120Hz
63 (79)
SIZE
RIPPLE
117
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
80 (100)
SIZE
RIPPLE
100 (125)
SIZE
RIPPLE
160 (200)
SIZE
RIPPLE
180 (225)
SIZE
RIPPLE
220
200 (250)
SIZE
RIPPLE
22 x 25
0.85
270
22 x 25
0.85
22 x 25
0.85
22 x 30
1.00
330
22 x 30
1.00
22 x 30
1.10
22 x 30
1.15
25 x 25
1.15
390
470
560
22 x 25
680
820
1000
1200
1500
22 x 30
22 x 25
22 x 30
1.20
1.35
1.20
1.35
22 x 30
1.15
22 x 35
1.32
22 x 35
1.30
25 x 25
1.15
25 x 25
1.25
25 x 30
1.30
22 x 35
1.30
22 x 40
1.47
22 x 40
1.52
25 x 30
1.30
25 x 30
1.40
25 x 35
1.54
30 x 25
1.49
22 x 40
1.57
22 x 45
1.70
22 x 45
1.70
25 x 30
1.50
25 x 35
1.63
25 x 35
1.65
30 x 25
1.54
30 x 25
1.60
30 x 30
1.72
22 x 45
1.75
22 x 50
1.87
25 x 45
1.97
25 x 35
1.70
25 x 40
1.82
30 x 35
1.97
30 x 30
1.77
30 x 30
1.80
35 x 30
2.02
35 x 25
1.84
22 x 30
1.50
22 x 50
2.03
25 x 45
2.05
25 x 45
2.20
25 x 25
1.50
25 x 40
1.97
30 x 35
2.05
30 x 35
2.10
30 x 30
1.95
35 x 30
2.11
35 x 30
2.16
35 x 25
1.99
22 x 35
1.70
25 x 45
2.15
25 x 50
2.27
30 x 45
2.32
25 x 30
1.70
30 x 35
2.15
30 x 40
2.29
35 x 35
2.30
35 x 30
2.21
35 x 30
2.25
22 x 35
1.59
22 x 40
1.97
30 x 40
2.45
30 x 45
2.57
30 x 50
2.75
25 x 25
1.50
25 x 35
1.99
35 x 35
2.52
35 x 35
2.55
35 x 40
2.75
30 x 25
1.95
35 x 40
2.85
35 x 45
2.90
22 x 40
1.78
22 x 45
2.15
30 x 50
2.75
25 x 30
1.70
25 x 40
2.19
35 x 40
2.75
30 x 25
1.75
30 x 30
2.15
35 x 25
2.21
Note: 1. Ripple Current: (A/rms) 105°C, 120Hz
118
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
1800
2200
2700
3300
3900
4700
5600
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
80 (100)
SIZE
RIPPLE
100 (125)
SIZE
RIPPLE
160 (200)
SIZE
RIPPLE
180 (225)
SIZE
RIPPLE
22 x 45
2.01
25 x 45
2.45
35 x 45
3.00
35 x 50
3.10
25 x 35
1.95
30 x 35
2.45
30 x 30
2.03
35 x 30
2.52
25 x 40
2.17
25 x 50
2.75
35 x 50
3.50
30 x 30
2.15
30 x 40
2.75
35 x 25
2.19
35 x 35
2.86
25 x 45
2.45
30 x 45
3.08
30 x 35
2.45
35 x 35
3.05
35 x 30
2.52
30 x 40
2.75
30 x 50
3.45
35 x 35
2.83
35 x 40
3.45
30 x 45
3.13
35 x 45
3.90
35 x 35
3.10
35 x 40
3.40
35 x 45
3.90
35 x 50
4.30
35 x 50
3.80
Note: 1. Ripple Current: (A/rms) 105°C, 120Hz
200 (250)
SIZE
RIPPLE
119
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
250 (300)
SIZE
RIPPLE
315 (365)
SIZE
RIPPLE
350 (400)
SIZE
RIPPLE
400 (450)
SIZE
RIPPLE
56
68
82
22 x 25
100
22 x 30
120
150
180
220
270
330
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
22 x 25
22 x 30
0.75
0.85
0.55
0.65
22 x 25
0.60
450 (500)
SIZE
RIPPLE
22 x 25
0.55
22 x 25
0.55
22 x 30
0.65
22 x 30
0.65
22 x 35
0.80
25 x 25
0.65
25 x 25
0.75
22 x 30
0.70
22 x 35
0.79
22 x 40
0.89
25 x 25
0.70
25 x 25
0.75
25 x 30
0.85
30 x 25
0.85
22 x 30
0.75
22 x 35
0.80
22 x 40
0.89
22 x 45
0.95
25 x 25
0.75
25 x 30
0.80
25 x 30
0.85
25 x 35
0.92
30 x 25
0.87
30 x 25
0.90
22 x 35
0.80
22 x 40
0.86
22 x 40
0.85
22 x 50
1.14
25 x 30
0.80
25 x 35
0.87
22 x 45
0.93
25 x 40
1.11
30 x 25
0.85
25 x 35
0.90
30 x 30
1.10
30 x 30
0.94
35 x 25
0.96
22 x 40
1.01
22 x 45
1.05
22 x 50
1.14
25 x 45
1.25
25 x 35
1.02
25 x 40
1.07
25 x 40
1.11
30 x 35
1.24
30 x 25
1.00
30 x 30
1.05
30 x 30
1.10
35 x 25
1.20
35 x 25
1.12
22 x 30
1.00
22 x 45
1.10
22 x 50
1.16
25 x 45
1.20
25 x 50
1.36
25 x 25
1.00
25 x 40
1.12
25 x 45
1.20
30 x 35
1.20
30 x 40
1.38
30 x 30
1.10
30 x 35
1.18
35 x 30
1.24
35 x 30
1.35
35 x 25
1.15
22 x 35
1.22
25 x 45
1.25
25 x 50
1.31
25 x 50
1.36
30 x 45
1.51
25 x 25
1.15
30 x 35
1.25
30 x 40
1.33
30 x 40
1.38
35 x 35
1.50
35 x 30
1.30
35 x 30
1.35
22 x 40
1.36
25 x 50
1.53
30 x 45
1.46
30 x 45
1.51
30 x 45
1.50
25 x 30
1.30
30 x 40
1.53
35 x 35
1.45
35 x 35
1.50
30 x 50
1.70
35 x 30
1.50
35 x 40
1.70
Note: 1. Ripple Current: (A/rms) 105°C, 120Hz
120
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
390
470
560
680
820
1000
1200
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
250 (300)
SIZE
RIPPLE
315 (365)
SIZE
RIPPLE
350 (400)
SIZE
RIPPLE
400 (450)
SIZE
RIPPLE
450 (500)
SIZE
RIPPLE
22 x 45
1.54
30 x 45
1.71
30 x 50
1.65
30 x 50
1.70
35 x 45
1.90
25 x 35
1.48
35 x 30
1.60
35 x 40
1.65
35 x 40
1.70
30 x 25
1.45
35 x 25
1.59
22 x 50
1.78
30 x 50
1.85
35 x 45
1.85
35 x 40
1.70
35 x 50
2.10
25 x 40
1.75
35 x 35
1.75
35 x 45
1.90
30 x 30
1.72
35 x 30
1.88
25 x 40
1.80
35 x 40
2.00
35 x 50
2.10
35 x 50
1.90
30 x 35
1.89
35 x 30
1.94
25 x 50
2.10
35 x 45
2.20
35 x 50
2.30
35 x 50
2.10
30 x 40
2.10
35 x 35
2.18
30 x 45
2.30
35 x 40
2.39
30 x 50
2.55
35 x 40
2.40
35 x 45
2.65
35 x 50
2.90
Note: 1. Ripple Current: (A/rms) 105°C, 120Hz
Yageo corporation ELECTROLYTIC CAPACITORS
LC [ High Temperature and Long Life ]
Large Can Aluminum
Electrolytic Capacitors
105°C 5000 Hours, Wide Temperature Range and Long Life
ELECTRICAL CHARACTERISTICS
Operating Temperature Range -25 ~ +105°C
Rated Voltage Range
160 ~ 450VDC
Rated Capacitance Range
270 ~ 2200μF
Capacitance Tolerance
±20% at 120Hz, 20°C
Leakage Current
Leakage Current (Max.) (20°C) : I = 0.02CV or 3μA whichever is greater.
(After Rated Voltage Applied for 5 Minutes)
Dissipation Factor (Max. tanδ) Rated Voltage (V)
Description
160~400
450
15
25
Longer life than HW, Snap-in termainal, High ripple current.
(20°C, 120Hz)
D.F (%)
Endurance
After the rated voltage has been applied at 105°C for 5000 hours, the
Applications: Smoothing circuit, TV/Monitor, Adapter, SMPS
capacitors shall meet the following requirements.
(b) Dissipation Factor: Not Exceeding 200% of the Specified Value
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
(c) Leakage Current: Not Exceeding the Specified Value
FREQUENCY (Hz)
50
120
400
COEFFICIENT
0.80 0.85
1.00
1.14
FREQUENCY (Hz)
IK
5K
10K
COEFFICIENT
1.23 1.30
1.36
1.40
(a) Capacitance Change : Within ±20% of Initial Value
Shelf Life
After having been placed at 105°C without voltage applied for 1000 hours,
the capacitors shall meet the same requirements as Endurance.
60
2.4K
diagram of dimensions
Unit: mm
Location of P.C.B. Holes
Vinyl Sleeve
Botton Plate
10±0.5
0.9±0.1
Negative
10±0.5
L+2 Max.
5.8±0.1
D±1
3.0
Safety Device
5.8±1.0
2mm x 2
1.5+0.2/-0.1
0.8+0.2/-0.1
122
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
160 (200)
SIZE
250 (300)
SIZE
RIPPLE
150
22 x 25
0.75
180
22 x 30
0.85
22 x 30
1.00
25 x 25
1.00
22 x 35
1.22
25 x 25
1.15
RIPPLE
180 (225)
SIZE
RIPPLE
220
270
330
390
470
560
680
820
1000
200 (250)
SIZE
22 x 25
22 x 25
22 x 30
0.85
1.00
22 x 25
22 x 30
0.85
1.10
22 x 30
RIPPLE
0.85
1.00
22 x 30
1.15
22 x 40
1.36
25 x 25
1.15
25 x 30
1.30
22 x 30
1.15
22 x 35
1.32
22 x 35
1.30
22 x 45
1.54
25 x 25
1.15
25 x 25
1.25
25 x 30
1.30
25 x 35
1.48
30 x 25
1.45
35 x 25
1.59
22 x 35
1.30
22 x 40
1.47
22 x 40
1.52
22 x 50
1.78
25 x 30
1.30
25 x 30
1.40
25 x 35
1.54
25 x 40
1.75
30 x 25
1.49
30 x 30
1.72
35 x 30
1.88
22 x 40
1.57
22 x 45
1.70
22 x 45
1.70
25 x 40
1.80
25 x 30
1.50
25 x 35
1.63
25 x 35
1.65
30 x 35
1.89
30 x 25
1.54
30 x 25
1.60
30 x 30
1.72
35 x 30
1.94
22 x 45
1.75
22 x 50
1.87
25 x 45
1.97
25 x 50
2.10
25 x 35
1.70
25 x 40
1.82
30 x 35
1.97
30 x 40
2.10
30 x 30
1.77
30 x 30
1.80
35 x 30
2.02
35 x 35
2.18
35 x 25
1.84
22 x 50
2.03
25 x 45
2.05
25 x 45
2.20
30 x 45
2.30
25 x 40
1.97
30 x 35
2.05
30 x 35
2.10
35 x 40
2.39
30 x 30
1.95
35 x 30
2.11
35 x 30
2.16
35 x 25
1.99
25 x 45
2.15
25 x 50
2.27
30 x 45
2.32
30 x 50
2.55
35 x 35
2.30
35 x 45
2.65
35 x 50
2.90
30 x 35
2.15
30 x 40
2.29
35 x 30
2.21
35 x 30
2.25
30 x 40
2.45
30 x 45
2.57
30 x 50
2.75
35 x 35
2.52
35 x 35
2.55
35 x 40
2.75
30 x 50
2.75
35 x 40
2.85
35 x 45
2.90
35 x 40
2.75
1800
35 x 45
3.00
35 x 50
3.10
2200
35 x 50
3.50
1200
1500
Note: 1. Ripple Current: (A/rms) 105°C, 120Hz
2. Dissipation Factor: 20°C, 120Hz
3. ESR: 120Hz / 20°C (Ω Max.)
123
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (µF)
315 (365)
SIZE
RIPPLE
350 (400)
SIZE
RIPPLE
400 (450)
SIZE
RIPPLE
56
68
82
100
120
150
180
220
270
330
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
22 x 25
22 x 30
0.55
0.65
22 x 25
0.60
450 (500)
SIZE
RIPPLE
22 x 25
0.55
22 x 25
0.55
22 x 30
0.65
22 x 30
0.65
22 x 35
0.80
25 x 25
0.65
25 x 25
0.75
22 x 30
0.70
22 x 35
0.79
22 x 40
0.89
25 x 25
0.70
25 x 25
0.75
25 x 30
0.85
22 x 30
0.75
22 x 35
0.80
22 x 40
0.89
22 x 45
0.95
25 x 25
0.75
25 x 30
0.80
25 x 30
0.85
25 x 35
0.92
30 x 25
0.87
30 x 25
0.90
22 x 35
0.80
22 x 40
0.86
22 x 45
0.93
22 x 50
1.14
25 x 30
0.80
25 x 35
0.87
25 x 35
0.90
25 x 40
1.11
30 x 25
0.85
30 x 30
0.94
30 x 30
1.10
35 x 25
0.96
22 x 40
1.01
22 x 45
1.05
22 x 50
1.14
25 x 45
1.25
25 x 35
1.02
25 x 40
1.07
25 x 40
1.11
30 x 35
1.24
30 x 25
1.00
30 x 30
1.05
30 x 30
1.10
35 x 25
1.20
35 x 25
1.12
22 x 45
1.10
22 x 50
1.16
25 x 45
1.20
25 x 50
1.36
25 x 40
1.12
25 x 45
1.20
30 x 35
1.20
30 x 40
1.38
30 x 30
1.10
35 x 30
1.24
35 x 30
1.35
30 x 35
1.18
35 x 25
1.15
25 x 45
1.25
25 x 50
1.31
25 x 50
1.36
30 x 45
1.51
30 x 35
1.25
30 x 40
1.33
30 x 40
1.38
35 x 35
1.50
35 x 30
1.30
35 x 30
1.35
25 x 50
1.53
30 x 45
1.46
30 x 45
1.51
30 x 50
1.70
30 x 40
1.53
35 x 35
1.45
35 x 35
1.50
35 x 40
1.70
35 x 30
1.50
30 x 45
1.71
30 x 50
1.65
30 x 50
1.70
35 x 45
1.90
35 x 30
1.60
35 x 40
1.65
35 x 40
1.70
30 x 50
1.85
35 x 45
1.85
35 x 45
1.90
35 x 50
2.10
35 x 35
1.75
560
35 x 40
2.00
35 x 50
2.10
680
35 x 45
2.20
390
470
Note: 1. Ripple Current: (A/rms) 105°C, 120Hz
2. Dissipation Factor: 20°C, 120Hz
3. ESR: 120Hz / 20°C (Ω Max.)
Yageo corporation ELECTROLYTIC CAPACITORS
Surface Mount
Aluminum Electrolytic
CA [ For General ]
ELECTRICAL CHARACTERISTICS
Operation Temperature Range -40 to +85°C
Rated Voltage Range
4 to 100VDC
Rated Capacitance Range
0.1 ~ 1000μF
Capacitance Tolerance
±20% at 120Hz, 20°C
Leakage Current (Max. 20°C)
I ≤ 0.01CV (μA) or 3μA whichever is greater.
(After 2 Minutes Application of DC Rated Voltage at 20°C)
feature
I = Leakage Current (μA), C = Rated Capacitance (μF), V = Rated Voltage (V)
For General Purpose Series with 85°C 2000 Hours
Low Temperature Stability
Suitable for AV (TV, Video, Audio) Monitor / Computer,
Home appliance, OA / HA / Communication
marking
Impedance Ratio at 120Hz (Max.)
W V (V)
4
6.3
10
16
25
35
50
63
100
Z (-25°C)
7
4
3
2
2
2
2
2
3
Z (-40°C)
15
8
6
4
4
3
3
3
2
After the rated voltage has been applied at 85°C for 2000 hours, the
Endurance
capacitors shall meet the following requirements.
1 0
(a) Capacitance Change: Within ±20% of the Initial Value
(b) Dissipation Factor: Not Exceeding 200% of Specified Value
(c) Leakage Current: Not Exceeding the Specified Value
Capacitance (F)
16G
Rated Voltage (VDC)
793
Date Code
Shelf Life
After having been placed at 85°C without voltage applied for 1000 hours,
the capacitors shall meet the same requirements as Endurance.
dimensions
Unit: mm
SIZE
CODE
Dø
L
A
H
I
W
P
K
B
4.0
5.4
4.3
5.5 Max.
1.8
0.65 ± 0.1 1.0±0.2
0.35 --- 0.20
C
5.0
5.4
5.3
6.5 Max.
2.2
0.65 ± 0.1 1.5±0.2
0.35 --- 0.20
D
6.3
5.4
6.6
7.8 Max.
2.6
0.65 ± 0.1 1.8±0.2
0.35 --- 0.20
E
8.0
6.5
8.3
9.5 Max.
3.4
0.65 ± 0.1 2.2±0.2
0.35 --- 0.20
F
8.0
10.5
8.3
10.0 Max. 3.4
0.90 ± 0.2 3.1±0.2
0.70 ± 0.20
G
10.0
10.5
10.3
12.0 Max. 3.5
0.90 ± 0.2 4.6±0.2
0.70 ± 0.20
H
6.3
7.7
6.6
7.8 Max.
0.65 ± 0.1 1.8±0.2
0.35 --- 0.20
K
0.3Max.
H
(I)
(P)
øD ± 0.5
(I)
A ± 0.2
W
( ) Reference Size
L ± 0.3
D ≥ ø8 = L ± 0.5
2.6
+ 0.15
+ 0.15
+ 0.15
+ 0.15
+ 0.15
125
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
D x L: mm
CAP. RATED VOLTAGE W V (SURGE VOLTAGE W V)
(μF)
4 (5)
SIZE
6.3 (8)
10 (13)
16 (20)
RIPPLE
DISSIPATION SIZE
RIPPLE
DISSIPATION SIZE
RIPPLE
DISSIPATION SIZE
RIPPLE
DISSIPATION
CURRENT FACTOR
CURRENT FACTOR
CURRENT FACTOR
CURRENT FACTOR
4.7
10
22
33
47
100
220
330
470
1000
1500
4 x 5.4
4 x 5.4
4 x 5.4
5 x 5.4
19
26
34
61
6.3 x 5.4 82
0.35
0.35
0.35
0.35
0.35
4 x 5.4
5 x 5.4
20
22
0.26
0.26
4 x 5.4
20
0.16
4 x 5.4
14
0.30
4 x 5.4
28
0.16
4 x 5.4
28
0.30
4 x 5.4
27
0.26
5 x 5.4
39
0.16
4 x 5.4
29
0.30
5 x 5.4
45
0.26
5 x 5.4
43
0.20
6.3 x 5.4 66
0.16
4 x 5.4
38
0.26
5 x 5.4
43
0.30
6.3 x 5.4 70
0.16
5 x 5.4
46
0.26
6.3 x 5.4 46
0.30
6.3 x 7.7 75
0.18
6.3 x 5.4 71
0.26
5 x 5.4
60
0.30
6.3 x 5.4 70
0.20
6.3 x 5.4 70
0.26
6.3 x 7.7 85
0.20
8 x 6.5
0.20
86
6.3 x 5.4 190
0.26
6.3 x 7.7 105
0.26
6.3 x 7.7 105
0.20
6.3 x 7.7 235
0.35
8 x 6.5
250
0.26
8 x 10.5 280
0.20
8 x 6.5
250
0.35
6.3 x 7.7 280
0.35
8 x 10.5 330
0.26
8 x 10.5 316
0.20
8 x 6.5
300
0.35
10 x 10.5 380
0.20
8 x 10.5 340
0.35
8 x 10.5 380
0.35
8 x 10.5 580
0.35
10 x 10.5 700
0.35
10 x 10.5 1000
0.35
Note: 1. Ripple Current: (mA/rms) 85°C, 120Hz
2. Dissipation Factor: 20°C, 120Hz
8 x 10.5 330
0.26
8 x 10.5 350
0.20
10 x 10.5 400
0.26
10 x 10.5 420
0.20
10 x 10.5 580
0.26
126
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
25 (32)
SIZE
RIPPLE
CURRENT
35 (44)
DISSIPATION SIZE
FACTOR
RIPPLE
CURRENT
50 (63)
DISSIPATION SIZE
FACTOR
RIPPLE
CURRENT
DISSIPATION
FACTOR
0.10
4 x 5.4
1
0.12
0.22
4 x 5.4
2
0.12
0.33
4 x 5.4
3
0.12
0.47
4 x 5.4
5
0.12
1.0
4 x 5.4
10
0.12
2.2
4 x 5.4
8
0.12
4 x 5.4
16
0.12
3.3
4 x 5.4
10
0.12
4 x 5.4
16
0.12
4.7
4 x 5.4
22
0.14
4 x 5.4
22
0.12
5 x 5.4
23
0.12
10
4 x 5.4
24
0.20
4 x 5.4
24
0.16
5 x 5.4
28
0.12
5 x 5.4
28
0.14
5 x 5.4
30
0.12
6.3 x 5.4
35
0.12
5 x 5.4
45
0.14
5 x 5.4
49
0.23
6.3 x 5.4
70
0.12
6.3 x 5.4
55
0.14
6.3 x 5.4
60
0.12
6.3 x 7.7
90
0.12
8 x 6.5
110
0.12
22
33
47
100
220
330
470
5 x 5.4
53
0.14
6.3 x 5.4
100
0.14
6.3 x 7.7
90
0.12
6.3 x 5.4
65
0.14
8 x 6.5
130
0.14
8 x 10.5
120
0.12
6.3 x 5.4
70
0.20
6.3 x 7.7
150
0.14
6.3 x 7.7
63
0.12
8 x 6.5
96
0.16
8 x 6.5
165
0.14
8 x 10.5
100
0.12
10 x 10.5
130
0.12
6.3 x 7.7
115
0.16
6.3 x 7.7
140
0.14
8 x 10.5
160
0.12
8 x 6.5
140
0.16
8 x 6.5
170
0.14
10 x 10.5
190
0.12
8 x 10.5
180
0.16
10 x 10.5
210
0.14
8 x 6.5
210
0.16
8 x 10.5
250
0.14
10 x 10.5
310
0.12
8 x 10.5
260
0.16
10 x 10.5
310
0.14
10 x 10.5
310
0.16
8 x 10.5
350
0.16
10 x 10.5
400
0.14
10 x 10.5
430
0.16
10 x 10.5
480
0.16
Note: 1. Ripple Current: (mA/rms) 85°C, 120Hz
2. Dissipation Factor: 20°C, 120Hz
127
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
63 (79)
SIZE
RIPPLE
CURRENT
DISSIPATION
FACTOR
3.3
100 (125)
SIZE
RIPPLE
CURRENT
DISSIPATION
FACTOR
8 x 10.5
30
0.18
4.7
6.3 x 5.4
20
0.18
8 x 10.5
50
0.18
10
6.3 x 5.4
20
0.18
8 x 10.5
55
0.18
22
8 x 10.5
30
0.18
10 x 10.5
60
0.18
33
8 x 10.5
30
0.18
10 x 10.5
65
0.18
47
8 x 10.5
30
0.18
100
10 x 10.5
60
0.18
Note: 1. Ripple Current: (mA/rms) 85°C, 120Hz
2. Dissipation Factor: 20°C, 120Hz
Yageo corporation ELECTROLYTIC CAPACITORS
Surface Mount
Aluminum Electrolytic
CB [ For General ]
ELECTRICAL CHARACTERISTICS
Operation Temperature Range -40 to +105°C
Rated Voltage Range
4 to 100VDC
Rated Capacitance Range
0.1 ~ 1000µF
Capacitance Tolerance
±20% at 120Hz, 20°C
Leakage Current (Max. 20°C)
I ≤ 0.01CV (μA) or 3μA Whichever is greater.
(After 2 Minutes Application of DC Rated Working Voltage at 20°C)
feature
Low Temperature Stability
Impedance Ratio at 120Hz
For General Purposes Series with 105°C 1000 Hours
W V (V)
4
6.3
10
16
25
35
50
63 100
Suitable for AV (TV, Video, Audio) Monitor / Computer,
OA / HA / Communication
Z (-25°C) / Z (+20°C)
7
4
3
2
2
2
2
2
2
Z (-40°C) / Z (+20°C)
15
8
6
4
4
3
3
3
3
Endurance
marking
After 1000 hours application of WV at 105°C, the capacitors shall meet
following requirements.
(a) Capacitance Change: Within ±20% of the Initial Value
(b) Dissipation Factor: Not Exceeding 200% of Specified Value
(c) Leakage Current: Not Exceeding the Specified Value
1 0
Capacitance (F)
Shelf Life
16G
Rated Voltage (VDC)
793
Date Code
After having been placed at 105°C without voltage applied for 1000 hours,
the capacitors shall meet the same requirements as Endurance.
dimensions
Unit: mm
SIZE
CODE
Dø
L
A
H
I
W
P
K
B
4.0
5.4
4.3
5.5 Max.
1.8
0.65 ± 0.1 1.0 ± 0.2 0.35 --- 0.20
C
5.0
5.4
5.3
6.5 Max.
2.2
0.65 ± 0.1 1.5 ± 0.2 0.35 --- 0.20
D
6.3
5.4
6.6
7.8 Max.
2.6
0.65 ± 0.1 1.8 ± 0.2 0.35 --- 0.20
E
8.0
6.5
8.3
9.5 Max.
3.4
0.65 ± 0.1 2.2 ± 0.2 0.35 --- 0.20
F
8.0
10.5
8.3
10.0 Max. 3.4
0.90 ± 0.2 3.1 ± 0.2 0.70 ± 0.20
G
10.0
10.5
10.3
12.0 Max. 3.5
0.90 ± 0.2 4.6 ± 0.2 0.70 ± 0.20
H
6.3
7.7
6.6
7.8 Max.
0.65 ± 0.1 1.8 ± 0.2 0.35 --- 0.20
K
0.3Max.
H
(I)
(P)
øD ± 0.5
(I)
A ± 0.2
W
( ) Reference Size
L ± 0.3
D ≥ ø8 = L ± 0.5
2.6
+ 0.15
+ 0.15
+ 0.15
+ 0.15
+ 0.15
129
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
D x L: mm
CAP. RATED VOLTAGE W V (SURGE VOLTAGE W V)
(μF)
4 (5)
SIZE
6.3 (8)
10 (13)
16 (20)
RIPPLE
DISSIPATION SIZE
RIPPLE
DISSIPATION SIZE
RIPPLE
DISSIPATION SIZE
RIPPLE
DISSIPATION
CURRENT FACTOR
CURRENT FACTOR
CURRENT FACTOR
CURRENT FACTOR
4.7
10
4 x 5.4
20
0.16
4 x 5.4
24
0.30
4 x 5.4
28
0.16
22
4 x 5.4
20
0.35
4 x 5.4
29
0.30
4 x 5.4
36
0.30
5 x 5.4
39
0.16
33
4 x 5.4
26
0.35
4 x 5.4
43
0.30
4 x 5.4
45
0.30
6.3 x 5.4 65
0.20
47
4 x 5.4
34
0.35
5 x 5.4
46
0.30
5 x 5.4
55
0.30
6.3 x 5.4 70
0.20
6.3 x 5.4 70
0.30
6.3 x 7.7 125
0.20
8 x 6.5
0.30
6.3 x 5.4 100
0.20
6.3 x 7.7 98
0.20
8 x 6.5
130
0.20
100
220
330
470
1000
5 x 5.4
61
6.3 x 5.4 82
0.35
0.35
5 x 5.4
58
0.35
6.3 x 5.4 71
0.35
110
6.3 x 5.4 95
0.35
6.3 x 7.7 115
0.30
6.3 x 7.7 100
0.20
6.3 x 7.7 120
0.35
8 x 10.5 160
0.26
10 x 10.5 210
0.20
8 x 6.5
130
0.35
6.3 x 7.7 175
0.35
10 x 10.5 230
0.26
10 x 10.5 230
0.20
8 x 10.5 230
0.35
10 x 10.5 260
0.35
10 x 10.5 270
0.26
8 x 10.5 230
0.20
10 x 10.5 275
0.20
10 x 10.5 380
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
2. Dissipation Factor: 20°C, 120Hz
0.35
10 x 10.5 390
0.26
130
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
25 (32)
SIZE
RIPPLE
CURRENT
35 (44)
DISSIPATION SIZE
FACTOR
RIPPLE
CURRENT
50 (63)
DISSIPATION SIZE
FACTOR
RIPPLE
CURRENT
DISSIPATION
FACTOR
0.10
4 x 5.4
1
0.12
0.22
4 x 5.4
2
0.12
0.33
4 x 5.4
3
0.12
0.47
4 x 5.4
5
0.12
1.0
4 x 5.4
10
0.12
2.2
4 x 5.4
15
0.12
4 x 5.4
16
0.12
3.3
4 x 5.4
18
0.12
4 x 5.4
16
0.12
4.7
4 x 5.4
22
0.14
4 x 5.4
22
0.12
5 x 5.4
23
0.12
10
4 x 5.4
23
0.14
5 x 5.4
30
0.12
6.3 x 5.4
35
0.12
5 x 5.4
28
0.14
5 x 5.4
45
0.14
6.3 x 5.4
60
0.14
6.3 x 7.7
65
0.12
6.3 x 5.4
55
0.14
8 x 6.5
70
0.12
6.3 x 5.4
65
0.16
6.3 x 7.7
70
0.12
8 x 10.5
91
0.12
22
33
47
100
220
84
0.14
6.3 x 5.4
65
0.16
6.3 x 7.7
72
0.14
6.3 x 7.7
65
0.12
8 x 6.5
91
0.16
8 x 6.5
76
0.14
10 x 10.5
100
0.12
8 x 10.5
98
0.14
6.3 x 7.7
95
0.16
6.3 x 7.7
105
0.14
8 x 10.5
120
0.12
8 x 6.5
100
0.16
8 x 10.5
130
0.14
10 x 10.5
145
0.12
8 x 10.5
130
0.16
10 x 10.5
160
0.14
8 x 10.5
220
0.16
10 x 10.5
240
0.14
10 x 10.5
273
0.16
10 x 10.5
570
0.16
330
470
8 x 6.5
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
2. Dissipation Factor: 20°C, 120Hz
131
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
63 (79)
SIZE
RIPPLE
CURRENT
DISSIPATION
FACTOR
3.3
100 (125)
SIZE
RIPPLE
CURRENT
DISSIPATION
FACTOR
8 x 10.5
30
0.18
4.7
6.3 x 5.4
20
0.18
8 x 10.5
50
0.18
10
6.3 x 5.4
20
0.18
8 x 10.5
55
0.18
22
8 x 10.5
30
0.18
10 x 10.5
60
0.18
33
8 x 10.5
30
0.18
10 x 10.5
65
0.18
47
8 x 10.5
30
0.18
100
10 x 10.5
60
0.18
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
2. Dissipation Factor: 20°C, 120Hz
Yageo corporation ELECTROLYTIC CAPACITORS
Surface Mount
Aluminum Electrolytic
CE [ For Long Life ]
ELECTRICAL CHARACTERISTICS
Operation Temperature Range -40 to +105°C
Rated Voltage Range
6.3 to 100VDC
Rated Capacitance Range
0.1 ~ 1000µF
Capacitance Tolerance
±20% at 120Hz, 20°C
Leakage Current (Max. 20°C)
I ≤ 0.01CV (μA) or 3μA whichever is greater.
(After Rated Voltage Applied for 2 Minutes)
feature
I = Leakage Current (μA), C = Rated Capacitance (μF), V = Rated Voltage (V)
For Long Life Series with 105°C 2000 Hours
Low Temperature Stability
Suitable for AV (TV, Video, Audio), Monitor / Computer,
OA / HA / Communication
marking
Impedance Ratio at 120Hz
W V (V)
Endurance
6.3
10
16
25
35
50
63
100
Z (-25°C) / Z (+20°C)
4
3
2
2
2
2
2
2
Z (-40°C) / Z (+20°C)
8
6
4
4
3
3
3
3
After the WV has been applied at 105°C for 2000 hours, the capacitors
shall meet following requirements.
(a) Capacitance Change: Within ±25% of the Initial Value for 4ø to 6.3ø
Within ±20% of the Initial Value for 8ø to 10ø
1 0
Capacitance (F)
(b) Dissipation Factor: Not Exceeding 200% of Specified Value
16D
Rated Voltage (VDC)
(c) Leakage Current: Not Exceeding the Specified Value
Date Code
793
Shelf Life
After having been placed at 105°C without voltage applied for 1000 hours,
the capacitors shall meet the same requirements as Endurance.
dimensions
Unit: mm
SIZE
CODE
Dø
L
A
H
I
W
P
K
B
4.0
5.4
4.3
5.5 Max.
1.8
0.65 ± 0.1 1.0 ± 0.2 0.35 --- 0.20
C
5.0
5.4
5.3
6.5 Max.
2.2
0.65 ± 0.1 1.5 ± 0.2 0.35 --- 0.20
D
6.3
5.4
6.6
7.8 Max.
2.6
0.65 ± 0.1 1.8 ± 0.2 0.35 --- 0.20
E
8.0
6.5
8.3
9.5 Max.
3.4
0.65 ± 0.1 2.2 ± 0.2 0.35 --- 0.20
F
8.0
10.5
8.3
10.0 Max. 3.4
0.90 ± 0.2 3.1 ± 0.2 0.70 ± 0.20
G
10.0
10.5
10.3
12.0 Max. 3.5
0.90 ± 0.2 4.6 ± 0.2 0.70 ± 0.20
H
6.3
7.7
6.6
7.8 Max.
0.65 ± 0.1 1.8 ± 0.2 0.35 --- 0.20
K
0.3Max.
H
(I)
(P)
øD ± 0.5
(I)
A ± 0.2
W
( ) Reference Size
L ± 0.3
D ≥ ø8 = L ± 0.5
2.6
+ 0.15
+ 0.15
+ 0.15
+ 0.15
+ 0.15
133
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
6.3 (8)
SIZE
RIPPLE
CURRENT
10 (13)
DISSIPATION SIZE
FACTOR
RIPPLE
CURRENT
16 (20)
DISSIPATION SIZE
FACTOR
RIPPLE
CURRENT
DISSIPATION
FACTOR
4.7
4 x 5.4
20
0.16
10
4 x 5.4
28
0.16
22
5 x 5.4
29
0.30
5 x 5.4
36
0.22
5 x 5.4
39
0.16
33
5 x 5.4
43
0.30
5 x 5.4
45
0.22
6.3 x 5.4
65
0.16
47
5 x 5.4
44
0.30
6.3 x 5.4
70
0.22
6.3 x 5.4
70
0.16
6.3 x 5.4
46
0.30
6.3 x 7.7
80
0.16
6.3 x 5.4
71
0.30
100
220
330
470
1000
6.3 x 5.4
85
0.30
6.3 x 5.4
100
0.20
6.3 x 7.7
104
0.30
6.3 x 7.7
130
0.20
8 x 6.5
110
0.30
8 x 10.5
140
0.20
10 x 10.5
210
0.20
10 x 10.5
230
0.20
10 x 10.5
275
0.20
6.3 x 7.7
115
0.35
6.3 x 7.7
105
0.30
8 x 10.5
150
0.35
8 x 10.5
160
0.30
8 x 10.5
230
0.35
8 x 10.5
190
0.30
10 x 10.5
230
0.26
10 x 10.5
270
0.26
10 x 10.5
390
0.26
8 x 10.5
260
0.35
10 x 10.5
260
0.35
10 x 10.5
380
0.35
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
2. Dissipation Factor: 20°C, 120Hz
134
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
25 (32)
SIZE
RIPPLE
CURRENT
35 (44)
DISSIPATION SIZE
FACTOR
RIPPLE
CURRENT
50 (63)
DISSIPATION SIZE
FACTOR
RIPPLE
CURRENT
DISSIPATION
FACTOR
0.10
4 x 5.4
1
0.12
0.22
4 x 5.4
2
0.12
0.33
4 x 5.4
3
0.12
0.47
4 x 5.4
5
0.12
1.0
4 x 5.4
10
0.12
2.2
4 x 5.4
16
0.12
3.3
4 x 5.4
16
0.12
4 x 5.4
18
0.12
5 x 5.4
23
0.12
4.7
4 x 5.4
22
0.14
5 x 5.4
23
0.12
6.8
4 x 5.4
25
0.14
5 x 5.4
27
0.12
5 x 5.4
30
0.12
10
5 x 5.4
28
0.14
5 x 5.4
30
0.12
5 x 5.4
35
0.12
22
6.3 x 5.4
55
0.14
6.3 x 5.4
60
0.14
8 x 10.5
70
0.12
33
6.3 x 5.4
65
0.14
6.3 x 7.7
79
0.14
8 x 10.5
91
0.12
8 x 6.5
84
0.14
8 x 10.5
98
0.14
10 x 10.5
100
0.12
10 x 10.5
160
0.14
10 x 10.5
145
0.12
10 x 10.5
240
0.14
10 x 10.5
200
0.12
47
6.3 x 5.4
70
0.16
6.3 x 7.7
86
0.16
8 x 6.5
91
0.16
6.3 x 7.7
90
0.16
8 x 10.5
130
0.16
8 x 10.5
220
0.16
10 x 10.5
273
0.16
330
10 x 10.5
334
0.16
470
10 x 10.5
300
0.16
100
220
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
2. Dissipation Factor: 20°C, 120Hz
135
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
63 (79)
SIZE
RIPPLE
CURRENT
DISSIPATION
FACTOR
3.3
100 (125)
SIZE
RIPPLE
CURRENT
DISSIPATION
FACTOR
8 x 10.5
30
0.18
4.7
8 x 10.5
25
0.18
8 x 10.5
80
0.18
10
8 x 10.5
25
0.18
8 x 10.5
85
0.18
22
10 x 10.5
45
0.18
10 x 10.5
85
0.18
33
10 x 10.5
45
0.18
10 x 10.5
90
0.18
47
10 x 10.5
55
0.18
Note: 1. Ripple Current: (mA/rms) 105°C, 120Hz
2. Dissipation Factor: 20°C, 120Hz
Yageo corporation ELECTROLYTIC CAPACITORS
Surface Mount
Aluminum Electrolytic
CZ [ For Low Impedance ]
ELECTRICAL CHARACTERISTICS
Operation Temperature Range -40 to +105°C
Rated Voltage Range
4 to 50VDC
Rated Capacitance Range
0.1 ~ 1000µF
Capacitance Tolerance
±20% at 120Hz, 20°C
Leakage Current (Max.20°C)
I ≤ 0.01CV (μA) or 3μA
(After 2 Minutes Application of DC Rated Voltage at 20°C)
feature
I = Leakage Current (μA), C = Rated Capacitance (μF), V = Rated Voltage (V)
For Low ESR Series with 105°C 1000 Hours
Low Temperature Stability
Suitable for AV (TV, Video, Audio), Monitor / Computer,
Battery Charger, DC / DC Converter, SMPS, Noise Filter
marking
Impedance Ratio at 120Hz
W V (V)
Endurance
6.3
10
16
25
35
50
Z (-25°C) / Z (+20°C) 4
4
2
2
2
2
2
2
Z (-40°C) / Z (+20°C) 8
4
4
3
3
3
3
After 1000 hours application of WV at 105°C, the capacitors shall meet
following requirements.
(a) Capacitance Change: Within ±20% of the Initial Value
(b) Dissipation Factor: Not Exceeding 200% of Specified Value
1 0
(c) Leakage Current: Not Exceeding the Specified Value
Capacitance (F)
16Z
Rated Voltage (VDC)
Shelf Life
After having been placed at 105°C without voltage applied for 1000 hours,
Date Code
793
the capacitors shall meet the same requirements as Endurance.
dimensions
Unit: mm
SIZE
CODE
Dø
L
A
H
I
W
P
B
4.0
5.4
4.3
5.5 Max.
1.8
0.65 ± 0.1 1.0± 0.2
0.35 --- 0.20
C
5.0
5.4
5.3
6.5 Max.
2.2
0.65 ± 0.1 1.5± 0.2
0.35 --- 0.20
D
6.3
5.4
6.6
7.8 Max.
2.6
0.65 ± 0.1 1.8± 0.2
0.35 --- 0.20
E
8.0
6.5
8.3
9.5 Max.
3.4
0.65 ± 0.1 2.2± 0.2
0.35 --- 0.20
F
8.0
10.5
8.3
10.0 Max. 3.4
0.90 ± 0.2 3.1± 0.2
0.70 ± 0.20
G
10.0
10.5
10.3
12.0 Max. 3.5
0.90 ± 0.2 4.6± 0.2
0.70 ± 0.20
H
6.3
7.7
6.6
7.8 Max.
0.65 ± 0.1 1.8± 0.2
0.35 --- 0.20
K
0.3Max.
H
(I)
(P)
øD ± 0.5
(I)
A ± 0.2
W
( ) Reference Size
L ± 0.3
D ≥ ø8 = L ± 0.5
2.6
K
+ 0.15
+ 0.15
+ 0.15
+ 0.15
+ 0.15
137
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
4 (5)
SIZE
RIPPLE
CURRENT
DISSIPATION ESR
FACTOR
6.3 (8)
SIZE
RIPPLE
CURRENT
DISSIPATION ESR
FACTOR
4.7
4 x 5.4
60
0.35
4.00
6.8
4 x 5.4
60
0.35
4.00
10
4 x 5.4
60
0.35
4.00
22
4 x 5.4
60
0.35
4.00
4 x 5.4
60
0.26
4.00
33
4 x 5.4
60
0.35
4.00
5 x 5.4
95
0.26
2.60
47
4 x 5.4
60
0.35
4.00
5 x 5.4
95
0.26
2.60
68
4 x 5.4
60
0.35
4.00
6.3 x 5.4
140
0.26
1.30
100
5 x 5.4
95
0.35
3.00
6.3 x 5.4
140
0.26
1.30
150
6.3 x 5.4
140
0.35
2.60
8 x 6.5
230
0.35
0.80
220
6.3 x 5.4
140
0.35
2.60
8 x 6.5
230
0.35
0.80
330
8 x 10.5
450
0.35
0.50
470
10 x 10.5
670
0.35
0.30
1000
10 x 10.5
670
0.35
0.30
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. Dissipation Factor: 20°C, 120Hz
3. ESR: 20°C, 100KHz (Ω)
138
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
10 (13)
SIZE
RIPPLE
CURRENT
DISSIPATION ESR
FACTOR
16 (20)
SIZE
RIPPLE
CURRENT
DISSIPATION ESR
FACTOR
4.7
4 x 5.4
60
0.16
4.00
6.8
4 x 5.4
60
0.16
4.00
10
4 x 5.4
60
0.22
4.00
4 x 5.4
60
0.16
4.00
22
5 x 5.4
95
0.22
2.60
5 x 5.4
95
0.16
2.60
33
5 x 5.4
95
0.22
2.60
5 x 5.4
95
0.16
2.60
47
6.3 x 5.4
95
0.22
1.30
6.3 x 5.4
140
0.16
1.30
68
6.3 x 5.4
140
0.22
1.30
8 x 6.5
230
0.20
0.80
100
6.3 x 5.4
140
0.22
1.30
8 x 6.5
230
0.20
0.80
150
8 x 6.5
230
0.26
0.80
10 x 10.5
450
0.20
0.50
220
8 x 6.5
230
0.26
0.80
10 x 10.5
450
0.20
0.50
330
8 x 10.5
450
0.26
0.50
10 x 10.5
670
0.20
0.30
470
10 x 10.5
670
0.26
0.30
10 x 10.5
670
0.20
0.30
1000
10 x 10.5
670
0.26
0.30
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. Dissipation Factor: 20°C, 120Hz
3. ESR: 20°C, 100KHz (Ω)
139
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP.
RATED VOLTAGE W V (SURGE VOLTAGE W V)
(μF)
25 (32)
SIZE
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
35 (44)
SIZE
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
D x L: mm
50 (63)
SIZE
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
0.10
4 x 5.4
60
0.12
5.00
0.22
4 x 5.4
60
0.12
5.00
0.33
4 x 5.4
60
0.12
5.00
0.47
4 x 5.4
60
0.12
5.00
1.0
4 x 5.4
60
0.12
4.00
4 x 5.4
60
0.12
5.00
2.2
4 x 5.4
60
0.12
4.00
4 x 5.4
60
0.12
5.00
3.3
4 x 5.4
60
0.12
4.00
4 x 5.4
60
0.12
5.00
95
0.12
4.00
4.7
4 x 5.4
60
0.14
4.00
4 x 5.4
60
0.12
4.00
5 x 5.4
6.8
4 x 5.4
60
0.14
4.00
5 x 5.4
95
0.12
2.60
6.3 x 5.4 140
0.12
2.60
10
5 x 5.4
95
0.14
2.60
5 x 5.4
95
0.12
2.60
6.3 x 5.4 140
0.12
2.60
22
6.3 x 5.4 140
0.14
1.30
6.3 x 5.4 140
0.12
1.30
8 x 6.5
230
0.12
1.30
33
6.3 x 5.4 140
0.14
1.30
8 x 6.5
230
0.14
0.80
8 x 10.5
300
0.12
1.10
47
6.3 x 5.4 140
0.14
1.30
8 x 6.5
230
0.14
0.80
10 x 10.5 670
0.12
0.80
68
8 x 10.5 450
0.16
0.50
8 x 10.5
450
0.14
0.50
10 x 10.5 670
0.12
0.80
100
8 x 10.5 450
0.16
0.50
10 x 10.5 670
0.14
0.30
10 x 10.5 670
0.12
0.80
150
10 x 10.5 670
0.16
0.30
10 x 10.5 670
0.14
0.30
220
10 x 10.5 670
0.16
0.30
10 x 10.5 670
0.14
0.30
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. Dissipation Factor: 20°C, 120Hz
3. ESR: 20°C, 100KHz (Ω)
Yageo corporation ELECTROLYTIC CAPACITORS
Surface Mount
Aluminum Electrolytic
CD [ For Ultra Low Impedance ]
ELECTRICAL CHARACTERISTICS
Operation Temperature Range -40 to +105°C
Rated Voltage Range
6.3 to 35VDC
Rated Capacitance Range
4.7 ~ 1500µF
Capacitance Tolerance
±20% at 120Hz, 20°C
Leakage Current (Max. 20°C)
I ≤ 0.01CV (µA) or 3µA
(After 2 Minutes Application of DC Rated Voltage at 20°C)
feature
I = Leakage Current (μA), C = Rated Capacitance (μF), V = Rated Voltage (V)
For Ultra Low Impedance Series with 105°C 2000 Hours
Dissipation Factor (tanδ)
W V(V)
6.3
10
16
25
35
Suitable for AV (TV, Video, Audio), Monitor / Computer,
OA / HA / Communication, SMPS
(120Hz, 20°C)
tan δ
0.26
0.19
0.16
0.14
0.12
Low Temperature Stability
Impedance Ratio at 120Hz
W V (V)
marking
Endurance
1 0
16
25
35
2
2
2
2
Z (-40°C) / Z (+20°C)
3
3
3
3
3
shall meet following requirements.
(a) Capacitance Change: Within ±30% of the Initial Value
Rated Voltage (VDC)
(b) Dissipation Factor: Not Exceeding 200% of Specified Value
Date Code
793
10
2
After the WV has been applied at 105°C for 2000 hours, the capacitors
Capacitance (F)
16E
6.3
Z (-25°C) / Z (+20°C)
(c) Leakage Current: Not Exceeding the Specified Value
Shelf Life
After having been placed at 105°C without voltage applied for 1000 hours,
the capacitors shall meet the same requirements as Endurance.
dimensions
Unit: mm
SIZE
CODE
Dø
L
A
H
I
W
P
K
B
4.0
5.4
4.3
5.5 Max.
1.8
0.65 ± 0.1 1.0 ± 0.2 0.35 --- 0.20
C
5.0
5.4
5.3
6.5 Max.
2.2
0.65 ± 0.1 1.5 ± 0.2 0.35 --- 0.20
D
6.3
5.4
6.6
7.8 Max.
2.6
0.65 ± 0.1 1.8 ± 0.2 0.35 --- 0.20
E
8.0
6.5
8.3
9.5 Max.
3.4
0.65 ± 0.1 2.2 ± 0.2 0.35 --- 0.20
F
8.0
10.5
8.3
10.0 Max. 3.4
0.90 ± 0.2 3.1 ± 0.2 0.70 ± 0.20
G
10.0
10.5
10.3
12.0 Max. 3.5
0.90 ± 0.2 4.6 ± 0.2 0.70 ± 0.20
H
6.3
7.7
6.6
7.8 Max.
0.65 ± 0.1 1.8 ± 0.2
K
0.3Max.
W
( ) Reference Size
+ 0.15
+ 0.15
H
(I)
(P)
øD ± 0.5
(I)
A ± 0.2
L ± 0.3
D ≥ ø8 = L ± 0.5
2.6
+ 0.15
+ 0.15
+ 0.15
0.35--- 0.20
141
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
22
33
47
6.3 (8)
SIZE
RIPPLE
ESR
10 (13)
SIZE
RIPPLE
ESR
16 (20)
SIZE
RIPPLE
ESR
4 x 5.4
90
1.93
4 x 5.4
90
1.93
4 x 5.4
90
1.93
5 x 5.4
160
1.00
5 x 5.4
160
1.00
5 x 5.4
160
1.00
6.3 x 5.4
240
0.52
4 x 5.4
90
1.93
4 x 5.4
90
1.93
5 x 5.4
160
1.00
5 x 5.4
160
1.00
6.3 x 5.4
240
0.52
150
8 x 6.5
240
220
8 x 6.5
240
100
330
470
680
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
5 x 5.4
160
1.00
6.3 x 5.4
190
0.52
0.52
6.3 x 5.4
240
0.52
0.30
6.3 x 7.7
240
0.34
6.3 x 7.7
280
0.34
0.30
6.3 x 7.7
280
0.34
6.3 x 7.7
330
0.34
8 x 6.5
300
0.26
8 x 10.5
370
0.22
8 x 10.5
600
0.16
8 x 10.5
600
0.16
8 x 10.5
600
0.16
8 x 10.5
600
0.16
10 x 10.5
600
0.08
10 x 10.5
850
0.08
10 x 10.5
850
0.08
0.34
8 x 6.5
300
0.26
8 x 10.5
600
0.16
0.16
820
1000
10 x 10.5
600
0.16
1200
10 x 10.5
700
0.16
1500
10 x 10.5
850
0.08
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω Max.)
1.93
190
280
600
90
6.3 x 5.4
6.3 x 7.7
8 x 10.5
4 x 5.4
10 x 10.5
600
0.12
142
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
25 (32)
SIZE
RIPPLE
ESR
4.7
10
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
4 x 5.4
90
1.93
35 (44)
SIZE
RIPPLE
ESR
4 x 5.4
90
1.93
4 x 5.4
90
1.93
5 x 5.4
160
1.00
22
5 x 5.4
160
1.00
5 x 5.4
160
1.00
33
5 x 5.4
160
1.00
6.3 x 5.4
240
0.52
6.3 x 5.4
240
0.52
47
6.3 x 5.4
240
0.52
6.3 x 5.4
240
0.52
68
6.3 x 5.4
240
0.52
6.3 x 7.7
280
0.34
100
6.3 x 7.7
280
0.34
6.3 x 7.7
280
0.34
8 x 6.5
300
0.26
8 x 10.5
600
0.16
10 x 10.5
850
0.08
150
8 x 10.5
600
0.16
8 x 10.5
600
0.16
220
8 x 10.5
600
0.16
10 x 10.5
600
0.16
330
10 x 10.5
600
0.16
10 x 10.5
850
0.08
470
10 x 10.5
850
0.08
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (Ω Max.)
Yageo corporation ELECTROLYTIC CAPACITORS
CH [ Ultra Low Impedance & High Temperature ]
Surface Mount
Aluminum Electrolytic
125°C 2000 Hours, Ultra Low Impedance High Temperature
ELECTRICAL CHARACTERISTICS
Operation Temperature Range -40 ~ +125°C
Rated Voltage Range
6.3 ~ 50VDC
Rated Capacitance Range
47 ~ 1000μF
Capacitance Tolerance
±20% at 120Hz, 20°C
Leakage Current (Max. 20°C)
I ≤ 0.01CV or 3μA (After Rated Voltage Applied for 2 Minutes)
I = Leakage Current (μA), C=Nominal Capacitance (μF),
feature
V=Rated Voltage (V)
125°C 2,000 hours, higher temperature range, low
profile vertical chip, low impedance
Dissipation Factor (Max.) (tanδ) Shown in the table of standard rating
(120Hz, 20°C)
Low Temperature Stability
W V (V) :
Endurance
Applications: Automatic Mounting and Reflow Soldering
Impedance Ratio (Max.)
6.3
10
16
25
35
50
Z-25°C/Z+20°C :
2
2
2
2
2
2
Z-40°C/Z+20°C :
3
3
3
3
3
3
After the rated voltage has been applied at 125°C for 1000~2000 hours,
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz)
120
COEFFICIENT
0.70 0.80
1K
10K
100K
0.90
1.00
the capacitors shall meet the following requirements.
(a) Capacitance Change: Within ±30% of the Initial Value
(b) Dissipation Factor: Not Exceeding 300% of Specified Value
(c) Leakage Current: Not Exceeding the Specified Value
Shelf Life
Dø :
8 x 6.5ø
≥8 x 10.5ø
Load Life :
1000hrs
2000hrs
After having been placed at 125°C without voltage applied for 1000 hours (500
hours for 8 x 6.5, the capacitors shall meet the same requirements as Endurance.
DIAGRAM OF DIMENSIONS
Dimensions: mm
K
0.3Max.
L
A
H
I
W
P
K
8.0
6.5
8.3
9.5 Max.
3.4
0.65 ± 0.1
2.2 ± 0.2
0.35 --- 0.75
(I)
Dø
H
(P)
øD ± 0.5
(I)
A ± 0.2
+ 0.15
8.0
10.5
8.3
10.0 Max. 3.4
0.90 ± 0.2
3.1 ± 0.2
0.70 ± 0.2
10.0
10.5
10.3
12.0 Max. 3.5
0.90 ± 0.2
4.6 ± 0.2
0.70 ± 0.2
W
( ) Reference Size
L ± 0.3
D ≥ ø8 = L ± 0.5
144
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP.
RATED VOLTAGE W V (SURGE VOLTAGE W V)
(μF)
6.3 (8)
SIZE
D x L: mm
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
10 (13)
SIZE
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
16 (20)
SIZE
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
100
8 x 6.5
100
0.30
0.50
8 x 6.5
100
0.26
0.50
8 x 6.5
100
0.20
0.50
150
8 x 6.5
100
0.30
0.50
8 x 6.5
100
0.26
0.50
8 x 10.5
197
0.20
0.30
220
8 x 6.5
100
0.30
0.50
8 x 10.5
197
0.26
0.30
8 x 10.5
197
0.20
0.30
330
8 x 10.5 197
0.30
0.30
8 x 10.5
197
0.26
0.30
8 x 10.5
197
0.20
0.30
470
8 x 10.5 197
0.30
0.30
10 x 10.5 297
0.26
0.20
10 x 10.5 297
0.20
0.20
680
10 x 10.5 297
0.30
0.20
10 x 10.5 297
0.26
0.20
1000
10 x 10.5 297
0.30
0.20
Note: 1. Ripple Current: (mA/rms) 125°C, 100KHz
2. Dissipation Factor: 20°C, 120Hz
3. ESR: 100KHz / 20°C (Ω Max.)
145
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
D x L: mm
CAP.
RATED VOLTAGE W V (SURGE VOLTAGE W V)
(μF)
25 (32)
SIZE
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
35 (44)
SIZE
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
50 (63)
SIZE
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
47
8 x 6.5
100
0.18
0.50
8 x 10.5
197
0.14
0.30
8 x 10.5
133
0.12
0.75
100
8 x 10.5 197
0.18
0.30
8 x 10.5
197
0.14
0.30
10 x 10.5 221
0.12
0.50
150
8 x 10.5 197
0.18
0.30
10 x 10.5 297
0.14
0.20
220
10 x 10.5 297
0.18
0.20
10 x 10.5 297
0.14
0.20
330
10 x 10.5 297
0.18
0.20
Note: 1. Ripple Current: (mA/rms) 125°C, 100KHz
2. Dissipation Factor: 20°C, 120Hz
3. ESR: 100KHz / 20°C (Ω Max.)
Yageo corporation ELECTROLYTIC CAPACITORS
Surface Mount
Aluminum Electrolytic
CX [ Ultra Low Impedance and Long Life ]
105°C 3000 ~ 5000 Hours, Ultra Low Impedance Long Life
ELECTRICAL CHARACTERISTICS
Operation Temperature Range -40 ~ +105°C
Rated Voltage Range
6.3 ~ 50VDC
Rated Capacitance Range
1 ~ 1000μF
Capacitance Tolerance
±20% at 120Hz, 20°C
Leakage Current (Max. 20°C)
I ≤ 0.01CV or 3μA (After Rated Voltage Applied for 2 Minutes)
I = Leakage Current (μA), C = Nominal Capacitance (μF),
feature
V = Rated Voltage (V)
105°C 3,000~5,000 hours, low profile vertical chip,
ultra low impedance
Applications: AV(TV, Video, Audio), Monitor/Computer,
OA/HA/Communication, SMPS
Dissipation Factor (Max.) (tanδ) Shown in the table of standard rating
(20°C, 120Hz)
Low Temperature Stability
Impedance Ratio (Max.)
W V (V) :
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz)
120
COEFFICIENT
0.70 0.80
1K
10K
100K
0.90
1.00
Endurance
6.3
10
16
25
35
50
Z-25°C/Z+20°C :
2
2
2
2
2
2
Z-40°C/Z+20°C :
3
3
3
3
3
3
After the rated voltage has been applied at 155°C for 3000~5000 hours,
the capacitors shall meet the following requirements.
(a) Capacitance Change: Within ±30% of Initial Value
(b) Dissipation Factor: Not Exceeding 200% of the Specified Value
(c) Leakage Current: Initial Specified Value or Less
Dø :
4 x 5.4~8 x 6.5ø
Load Life :
Shelf Life
≥8 x 10.5~10 x 10.5ø
3000hrs
5000hrs
After having been placed at 105°C without voltage applied for 1000 hours,
the capacitors shall meet the same requirements as Endurance.
dimensions
Unit: mm
Dø
L
A
H
I
W
P
K
4.0
5.4
4.3
5.5 Max.
1.8
0.65 ± 0.1
1.0 ± 0.2
0.35 --- 0.20
5.0
5.4
5.3
6.5 Max.
2.2
0.65 ± 0.1
1.5 ± 0.2
0.35 --- 0.20
6.3
5.4
6.6
7.8 Max.
2.6
0.65 ± 0.1
1.8 ± 0.2
0.35 --- 0.20
6.3
7.7
6.6
7.8 Max.
2.6
0.65 ± 0.1
1.8 ± 0.2
0.35 --- 0.20
8.0
6.5
8.3
9.5 Max.
3.4
0.65 ± 0.1
2.2 ± 0.2
0.35 --- 0.20
8.0
10.5
8.3
10.0 Max. 3.4
0.90 ± 0.2
3.1 ± 0.2
0.70 ± 0.20
10.0
10.5
10.3
12.0 Max. 3.5
0.90 ± 0.2
4.6 ± 0.2
0.70 ± 0.20
K
0.3Max.
H
(I)
(P)
øD ± 0.5
(I)
A ± 0.2
W
( ) Reference Size
L ± 0.3
D ≥ ø8 = L ± 0.5
+ 0.15
+ 0.15
+ 0.15
+ 0.15
+ 0.15
147
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP.
RATED VOLTAGE W V (SURGE VOLTAGE W V)
(μF)
6.3 (8)
SIZE
D x L: mm
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
10 (13)
SIZE
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
16 (20)
SIZE
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
22
4 x 5.4
90
0.26
1.93
4 x 5.4
90
0.19
1.93
5 x 5.4
160
0.16
1.00
33
4 x 5.4
90
0.26
1.93
5 x 5.4
160
0.19
1.00
6.3 x 5.4 240
0.16
0.52
47
5 x 5.4
160
0.26
1.00
6.3 x 5.4 190
0.19
0.52
6.3 x 5.4 240
0.16
0.52
100
6.3 x 5.4 240
0.26
0.52
6.3 x 5.4 190
0.19
0.52
6.3 x 7.7 280
0.16
0.34
150
8 x 6.5
240
0.26
0.30
6.3 x 7.7 240
0.19
0.34
8 x 10.5
370
0.16
0.22
220
8 x 6.5
240
0.26
0.30
8 x 10.5
600
0.19
0.16
8 x 10.5
370
0.16
0.22
330
8 x 10.5 600
0.26
0.16
8 x 10.5
600
0.19
0.16
8 x 10.5
600
0.16
0.16
470
8 x 10.5 600
0.26
0.16
10 x 10.5 850
0.19
0.12
10 x 10.5 850
0.16
0.12
680
10 x 10.5 850
0.26
0.12
10 x 10.5 850
0.19
0.12
1000
10 x 10.5 850
0.26
0.12
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. Dissipation Factor: 20°C, 120Hz
3. ESR: 100KHz / 20°C (Ω Max.)
148
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP.
RATED VOLTAGE W V (SURGE VOLTAGE W V)
(μF)
25 (32)
SIZE
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
35 (44)
SIZE
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
D x L: mm
50 (63)
SIZE
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
1.0
4 x 5.4
60
0.12
5.00
2.2
4 x 5.4
60
0.12
5.00
3.3
4 x 5.4
60
0.12
5.00
95
0.12
4.00
4.7
4 x 5.4
90
0.12
1.93
5 x 5.4
10
4 x 5.4
90
0.14
1.93
5 x 5.4
160
0.12
1.00
6.3 x 5.4 140
0.12
2.60
22
5 x 5.4
160
0.14
1.00
5 x 5.4
160
0.12
1.00
8 x 6.5
230
0.12
1.30
33
6.3 x 5.4 240
0.14
0.52
6.3 x 5.4 240
0.12
0.52
8 x 10.5
350
0.12
0.50
47
6.3 x 5.4 240
0.14
0.52
6.3 x 7.7 280
0.12
0.34
10 x 10.5 670
0.12
0.34
68
6.3 x 7.7 280
0.14
0.34
6.3 x 7.7 280
0.12
0.34
10 x 10.5 670
0.12
0.34
100
8 x 6.5
300
0.14
0.26
8 x 10.5
600
0.12
0.16
10 x 10.5 670
0.12
0.34
150
8 x 10.5 600
0.14
0.16
10 x 10.5 850
0.12
0.12
220
8 x 10.5 600
0.14
0.16
10 x 10.5 850
0.12
0.12
330
10 x 10.5 850
0.14
0.12
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. Dissipation Factor: 20°C, 120Hz
3. ESR: 100KHz / 20°C (Ω Max.)
Yageo corporation ELECTROLYTIC CAPACITORS
CP [ Ultra Low ESR & High Ripple Current ]
Conductive
Polymer Solid Capacitors
105°C, 2000 Hours 8mm Height and Ultra Low ESR
ELECTRICAL CHARACTERISTICS
Operation Temperature Range -55 ~ +105°C
Rated Voltage Range
2.5 ~ 6.3VDC
Rated Capacitance Range
470 ~ 820μF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current (Max. 20°C)
I ≤ 0.2CV (μA) ( After Rated Voltage Applied for 2 Minutes )
I = Leakage Current (μA), C = Rated Capacitance (μF), V = Rated Voltage (V)
Dissipation Factor
W V(V)
2.5 ~ 6.3V
at 120Hz, 20°C
D.F (%)
8
Low Temperature Stability
Impedance Ratio at 20°C (Max.)
Endurance
description
Recommended Applications: Montherboard, DC / DC
Converter, DSC, PDA, HD Drive, MO Drive, DVD
Drive, Navigation system, Portable Communication
Devices
W V (V)
2.5 ~ 16V (Rated Voltage)
Impedance
Z - 25°C / Z + 20°C
≤1.15
Z - 55°C / Z + 20°C
≤1.25
After the rated voltage has been applied at 105°C for 2000 hours, the
capacitors shall meet the follow requirements.
(a) Appearance: No Significant Damage
(b) Capacitance Change: Within ±20% of the Initial Value
(c) Dissipation Factor: Not Exceeding 150% of the Initial Specified Value
(d) Equivalent Series Resistance: Not Exceeding 150% of the
Initial Specified Value
(e) Leakage Current: Not more than the Initial Specified Value
Humidity Test
After subjected 90 to 95% RH for 1000 hours at 60°C, the capacitors shall
meet the requirements as Endurance.
diagram of dimensions
Unit: mm
MARKING
Rubber Stand-off
Coated case
1 0
ø0.6
P±0.5
øD+0.5 max.
2.5CP
793
Capacitance(µF)
Series Identification
Rated Voltage
Date Code
Dø
P
a (Max.)
8
3.5
1.5
L +a
15Min.
4Min.
D±0.5
Polarity (negative) Indication
150
case size & permissible ripple current of standard products
CAP. (µF)
D x L: mm
Rated Voltage W V
2.5
SIZE
RIPPLE
ESR
4
SIZE
RIPPLE
ESR
470
560
8x8
4400
6
820
8x8
4400
6
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (mΩ)
8x8
4400
7
6.3
SIZE
RIPPLE
8x8
4400
8
8x8
4400
8
ESR
Yageo corporation ELECTROLYTIC CAPACITORS
CG [ Low ESR & High Ripple Current ]
Conductive
Polymer Solid Capacitors
105°C, 2000 Hours and Ultra Low ESR
ELECTRICAL CHARACTERISTICS
Operation Temperature Range -55 ~ +105°C
Rated Voltage Range
2.5 ~ 25VDC
Rated Capacitance Range
33 ~ 2700μF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current (Max. 20°C)
I ≤ 0.2CV (μA) ( After Rated Voltage Applied for 2 Minutes )
I = Leakage Current (μA), C = Rated Capacitance (μF), V = Rated Voltage (V)
Dissipation Factor
W V(V)
2.5 ~ 10V
16 ~ 25
at 120Hz, 20°C
D.F (%)
8
12
Low Temperature Stability
Impedance Ratio at 20°C (Max.)
Endurance
description
Long life for 2000 hours at 105°C, ideally suited for
high quality and high reliability applications.
Featuring high CV products
W V (V)
2.5 ~ 16V
Impedance
Z - 25°C / Z + 20°C
≤1.15
Z - 55°C / Z + 20°C
≤1.25 (Z: 100KHz)
After the rated voltage has been applied at 105°C for 2000 hours, the
capacitors shall meet the follow requirements.
(a) Appearance: No Significant Damage
(b) Capacitance Change: Within±20% of Initial Value
(c) Dissipation Factor: Not Exceeding 150% of the Initial Specified Value
(d) Equivalent Series Resistance: Not Exceeding 150% of the
Initial Specified Value
(e) Leakage Current: Not Exceeding the Initial Specified Value
Humidity Test
After subjected to 90 to 95% RH for 1000 hours at 60°C, the capacitors
shall meet the requirements as Endurance.
diagram of dimensions
Unit: mm
MARKING
Rubber Stand-off
Coated case
a (Max.)
6
2.5
1.0
8
3.5
10
5.0
1 0
2.5CG
P±0.5
P
øD+0.5 max.
Dø
ø0.6
793
Capacitance(µF)
Series Identification
Rated Voltage
Date Code
L+a
15Min.
4Min.
D+0.5max
Polarity (negative) Indication
152
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
2.5
SIZE
6.3
SIZE
RIPPLE
ESR
270
6.3 x 10.5
3160
28.00
330
6.3 x 10.5
3190
28.00
6.3 x 10.5
3190
28.00
8 x 11.5
5600
7.00
8 x 11.5
5600
7.00
10 x 11.5
5050
7.00
10 x 11.5
5050
7.00
10 x 12.5
5600
7.00
10 x 12.5
5600
7.00
RIPPLE
ESR
4
SIZE
RIPPLE
ESR
180
390
6.3 x 10.5
3160
20.00
470
560
6.3 x 10.5
3160
20.00
680
820
1000
6.3 x 10.5
8 x 11.5
3160
5600
3160
20.00
8 x 11.5
5600
7.00
20.00
7.00
1200
1500
6.3 x 10.5
8 x 11.5
5600
7.00
10 x 11.5
5050
7.00
8 x 11.5
5600
7.00
10 x 11.5
5050
7.00
10 x 11.5
5050
7.00
10 x 12.5
5600
7.00
1800
10 x 12.5
5600
7.00
10 x 12.5
5600
7.00
2700
10 x 12.5
5600
7.00
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (mΩ)
153
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
10
SIZE
25
SIZE
RIPPLE
ESR
33
8 x 11.5
2980
30.00
47
8 x 11.5
2980
30.00
56
8 x 11.5
2980
30.00
RIPPLE
ESR
16
SIZE
RIPPLE
ESR
100
6.3 x 10.5
2820
25.00
150
6.3 x 10.5
2820
25.00
180
6.3 x 10.5
2820
25.00
8 x 11.5
4360
16.00
220
6.3 x 10.5
2820
25.00
8 x 11.5
5000
11.00
8 x 11.5
5000
11.00
8 x 11.5
5000
8.00
10 x 11.5
4000
10.00
10 x 12.5
6100
10.00
10 x 12.5
5050
14.00
10 x 12.5
5050
14.00
10 x 12.5
5050
14.00
270
330
8 x 11.5
5600
7.00
390
470
8 x 11.5
5600
7.00
10 x 11.5
4000
7.00
560
10 x 12.5
5050
7.00
820
10 x 12.5
5050
7.00
Note: 1. Ripple Current: (mA/rms) 105°C, 100KHz
2. ESR: 100KHz / 20°C (mΩ)
Yageo corporation ELECTROLYTIC CAPACITORS
Screw Type Aluminum
Electrolytic Capacitors
NP [ For General ]
For Large Power Source, Converter Circuit
ELECTRICAL CHARACTERISTICS
Operating Temperature Range -40 to +85°C
-25 to +85°C
Rated Voltage Range
10 ~ 250V
315 ~ 450V
Rated Capacitance Range
1800 ~ 820000μF
Capacitance Tolerance
±20% (120Hz, +20°C)
Leakage Current
I = 0.02CV or 5mA whichever is smaller.
(After 5 Minutes Application of DC Rated Voltage at 20°C)
Description
Dissipation Factor
Endurance : 85°C, 2000 Hours
at 120Hz, +20°C
It is suitable for high ripple current, large power source,
converter circuit, etc.
Endurance
After the rated voltage has been applied at 85°C for 2000 hours, and then
has resumed its original condition for 16 hours.
(a) Capacitance Change: ±20% Initial Measured Value
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
50
10~50V
0.95 1.00
1.04 1.10
63~100V
0.95 1.00
1.06 1.16
160~200V
0.90 1.00
1.10 1.20
250~450V
0.80 1.00
1.10 1.20
FREQUENCY (Hz)
3K 5K
10K 20K
10~50V
1.12 1.13
1.15 1.15
63~100V
1.20 1.25
1.30 1.36
160~200V
1.35 1.40
1.50 1.55
250~450V
1.35 1.40
1.50 1.55
(b) Dissipation Factor: ≤ 2 Times Initial Specified Value
(c) Leakage Current: ≤ Initial Specified Value
100 (120) 300 1K
Shelf Life
After having been stored for 1000 hours at 85°C, the rated voltage has
been applied for 30 minutes, and then has resumed its original condition for
16 hours.
(a) Capacitance Change: ±20% Initial Measured Value
(b) Dissipation Factor: ≤ 2 Times Initial Specified Value
(c) Leakage Current: ≤ Initial Specified Value
diagram of dimensions
Sleeve
M5x0.8
Safety Vent
F ±1
FREQUENCY (Hz)
Less than the Value Specified in the Standard Product Tables
L ±2
20max
Dø±1
Unit: mm
Dø
F
35
12.7
51
22
63.5
28.6
76
32
89
32
155
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP.
RATED VOLTAGE W V (SURGE VOLTAGE W V)
(μF)
10 (13)
SIZE
16 (20)
RIPPLE
DISSIPATION SIZE
CURRENT FACTOR
25 (32)
RIPPLE
DISSIPATION SIZE
CURRENT FACTOR
D x L: mm
35 (44)
RIPPLE
DISSIPATION SIZE
CURRENT FACTOR
RIPPLE
DISSIPATION
CURRENT FACTOR
10000
35 x 50
3.40
0.40
12000
35 x 50
3.70
0.40
15000
35 x 50
3.70
0.50
35 x 65
4.20
0.40
18000
35 x 50
4.10
0.50
35 x 80
4.90
0.40
22000
35 x 50
4.10
0.60
35 x 50
4.50
0.50
35 x 80
5.70
0.40
27000
35 x 50
4.50
0.60
35 x 65
5.00
0.50
35 x 100 6.30
0.40
33000
35 x 50
4.30
0.80
35 x 50
5.00
0.60
35 x 80
5.90
0.50
35 x 100 7.20
0.40
39000
35 x 50
4.70
0.80
35 x 65
5.90
0.60
35 x 80
6.70
0.50
35 x 120 7.30
0.50
47000
35 x 65
5.20
0.80
35 x 80
6.40
0.60
35 x 100 7.70
0.50
35 x 120 8.70
0.50
56000
35 x 80
6.10
0.80
35 x 80
7.30
0.60
35 x 100 7.90
0.60
51 x 95
8.60
0.60
68000
35 x 80
6.70
0.80
35 x 100 8.40
0.60
35 x 120 9.10
0.60
51 x 95
9.80
0.60
82000
35 x 100 7.70
0.80
35 x 100 8.30
0.80
35 x 120 10.40
0.60
51 x 115 11.60
0.60
100000 35 x 100 8.80
0.80
35 x 120 9.50
0.80
51 x 95
10.30
0.80
63.5 x 95 13.30
0.60
120000 35 x 120 10.00
0.80
35 x 120 10.90
0.80
51 x 115 11.70
0.80
63.5 x 115 14.80
0.60
150000 35 x 120 10.80
1.00
51 x 95
11.30
1.00
51 x 130 14.10
0.80
63.5 x 120 14.90
0.80
180000 51 x 95
12.00
1.00
51 x 115 12.80
1.00
63.5 x 95 15.70
0.80
63.5 x 130 17.00
0.80
220000 51 x 120 11.20
1.50
51 x 130 15.30
1.00
63.5 x 115 16.10
1.00
76 x 115 20.00
0.80
270000 51 x 120 12.80
1.50
63.5 x 95 17.60
1.00
63.5 x 130 18.60
1.00
76 x 130 20.30
1.00
330000 63.5 x 95 15.30
1.50
63.5 x 115 16.80
1.50
63.5 x 155 21.90
1.00
76 x 155 23.50
1.00
390000 63.5 x 115 17.30
1.50
63.5 x 130 18.30
1.50
76 x 120 22.00
1.20
89 x 130 26.40
1.00
470000 63.5 x 130 16.70
2.00
76 x 120 21.30
1.50
76 x 155 25.60
1.20
89 x 155 29.60
1.00
560000 76 x 115 19.00
2.00
76 x 130 23.60
1.50
89 x 130 27.90
1.20
680000 76 x 130 21.70
2.00
76 x 155 27.60
1.50
89 x 155 32.50
1.20
820000 76 x 155 24.70
2.00
89 x 155 27.10
2.00
Note: 1. Ripple Current: (A/rms) 85°C, 120Hz
2. Dissipation Factor: 120Hz / 20°C
156
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP.
RATED VOLTAGE W V (SURGE VOLTAGE W V)
(μF)
50 (63)
SIZE
63 (72)
RIPPLE
DISSIPATION SIZE
CURRENT FACTOR
D x L: mm
80 (100)
100 (125)
RIPPLE
DISSIPATION SIZE
RIPPLE
DISSIPATION SIZE
RIPPLE
DISSIPATION
CURRENT FACTOR
CURRENT FACTOR
CURRENT FACTOR
1800
35 x 50
1.90
0.25
2200
35 x 50
2.10
0.25
2700
35 x 50
2.30
0.25
3300
35 x 50
2.50
0.25
35 x 65
2.60
0.25
3900
35 x 50
2.70
0.25
35 x 50
2.80
0.25
35 x 80
3.00
0.25
4700
35 x 50
3.00
0.25
35 x 65
3.00
0.25
35 x 80
3.50
0.25
5600
35 x 50
3.00
0.30
35 x 50
3.30
0.25
35 x 80
3.60
0.25
35 x 100 3.90
0.25
6800
35 x 50
3.30
0.30
35 x 65
3.60
0.25
35 x 80
3.90
0.25
35 x 100 4.50
0.25
8200
35 x 50
3.60
0.30
35 x 80
4.30
0.25
35 x 80
4.50
0.25
35 x 120 5.10
0.25
10000
35 x 65
4.00
0.30
35 x 80
4.90
0.25
35 x 100 5.20
0.25
35 x 120 5.90
0.25
12000
35 x 80
4.70
0.30
35 x 100 5.60
0.25
35 x 100 5.90
0.25
51 x 75
6.40
0.25
15000
35 x 80
5.50
0.30
35 x 100 5.90
0.30
35 x 120 6.80
0.25
51 x 95
7.00
0.25
18000
35 x 100 6.20
0.30
35 x 120 6.70
0.30
35 x 120 7.80
0.25
51 x 115 8.30
0.25
22000
35 x 120 6.30
0.40
35 x 120 7.80
0.30
51 x 95
8.00
0.30
51 x 130 10.00
0.25
27000
35 x 120 7.10
0.40
51 x 95
7.40
0.40
51 x 95
9.20
0.30
63.5 x 115 11.50
0.25
33000
51 x 95
8.20
0.40
51 x 95
8.40
0.40
51 x 115 10.50
0.30
63.5 x 130 11.90
0.25
39000
51 x 95
8.10
0.50
51 x 115 9.50
0.40
51 x 130 12.00
0.30
76 x 115 13.40
0.25
47000
51 x 115 9.30
0.50
51 x 130 11.30
0.40
63.5 x 115 13.60
0.30
76 x 130 14.20
0.35
56000
63.5 x 95 10.50
0.50
63.5 x 115 12.80
0.40
63.5 x 130 13.40
0.40
76 x 155 16.00
0.35
68000
63.5 x 95 12.00
0.50
63.5 x 120 12.70
0.50
76 x 115 15.40
0.40
89 x 130 18.80
0.35
82000
63.5 x 115 13.70
0.50
63.5 x 130 14.50
0.50
76 x 130 17.50
0.40
89 x 155 20.50
0.35
100000 76 x 115 14.70
0.60
76 x 115 16.70
0.50
76 x 155 20.50
0.40
89 x 171 24.00
0.35
120000 76 x 120 16.70
0.60
76 x 130 18.90
0.50
89 x 130 22.70
0.40
150000 76 x 130 19.30
0.60
76 x 155 22.40
0.50
89 x 155 26.50
0.40
180000 76 x 155 21.90
0.60
89 x 130 22.40
0.60
220000 89 x 130 21.40
0.60
89 x 155 26.20
0.60
27000
0.60
89 x 155 24.60
Note: 1. Ripple Current: (A/rms) 85°C, 120Hz
2. Dissipation Factor: 120Hz / 20°C
157
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
D x L: mm
CAP.
RATED VOLTAGE W V (SURGE VOLTAGE W V)
(μF)
160 (200)
200 (250)
250 (300)
350 (400)
SIZE
RIPPLE
DISSIPATION SIZE
RIPPLE
DISSIPATION SIZE
RIPPLE
DISSIPATION SIZE
RIPPLE
DISSIPATION
CURRENT FACTOR
CURRENT FACTOR
CURRENT FACTOR
CURRENT FACTOR
390
35 x 50
1.67
0.20
470
35 x 80
2.15
0.20
560
35 x 80
2.37
0.20
680
35 x 80
2.59
0.20
820
35 x 100 3.07
0.20
1000
35 x 100 3.41
0.20
1200
51 x 75
3.81
0.20
1500
35 x 100 3.22
0.25
51 x 75
4.26
0.20
1800
35 x 100 3.52
0.25
51 x 95
5.14
0.20
2200
35 x 100 3.92
0.25
51 x 75
4.00
0.25
51 x 95
5.70
0.20
2700
35 x 120 4.70
0.25
51 x 75
4.44
0.25
51 x 130 7.14
0.20
3300
35 x 120 5.18
0.25
51 x 75
4.92
0.25
51 x 95
5.40
0.25
51 x 130 7.92
0.20
3900
51 x 75
5.33
0.25
51 x 75
5.33
0.25
51 x 115 6.29
0.25
63.5 x 115 9.00
0.20
4700
51 x 75
5.85
0.25
51 x 95
6.44
0.25
63.5 x 95 7.10
0.25
63.5 x 130 10.33
0.20
5600
51 x 95
7.03
0.25
51 x 115 7.55
0.25
63.5 x 95 7.77
0.25
76 x 115 11.36
0.20
6800
51 x 95
7.77
0.25
51 x 130 8.77
0.25
63.5 x 115 9.14
0.25
76 x 130 13.10
0.20
8200
51 x 115 9.14
0.25
63.5 x 95 9.40
0.25
63.5 x 115 10.03
0.25
76 x 155 15.43
0.20
10000
63.5 x 95 10.36
0.25
63.5 x 95 10.36
0.25
63.5 x 130 11.66
0.25
89 x 155 18.13
0.20
12000
63.5 x 95 11.32
0.25
76 x 95
12.06
0.25
76 x 115 12.88
0.25
89 x 155 20.02
0.20
15000
63.5 x 130 14.28
0.25
76 x 95
14.43
0.25
76 x 130 15.10
0.25
89 x 195 24.50
0.20
18000
63.5 x 130 15.61
0.25
76 x 130 16.50
0.25
76 x 155 17.69
0.25
89 x 235 28.83
0.20
22000
76 x 130 18.28
0.25
76 x 155 19.61
0.25
89 x 155 20.91
0.25
27000
76 x 130 20.24
0.25
89 x 130 21.51
0.25
30000
89 x 130 23.75
0.25
89 x 155 25.53
0.25
39000
89 x 155 27.86
0.25
Note: 1. Ripple Current: (A/rms) 85°C, 120Hz.
2. Dissipation Factor: 120Hz / 20°C
158
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
400 (450)
SIZE
RIPPLE
CURRENT
DISSIPATION
FACTOR
270
450 (500)
SIZE
RIPPLE
CURRENT
DISSIPATION
FACTOR
35 x 50
1.37
0.20
330
35 x 50
1.52
0.20
35 x 80
1.82
0.20
390
35 x 80
1.96
0.20
35 x 80
1.96
0.20
470
35 x 80
2.15
0.20
35 x 80
2.15
0.20
560
35 x 80
2.37
0.20
35 x 100
2.55
0.20
680
35 x 100
1.82
0.20
35 x 100
2.81
0.20
820
35 x 100
3.07
0.20
51 x 75
3.18
0.20
1000
51 x 75
3.48
0.20
51 x 75
3.48
0.20
1200
51 x 75
3.82
0.20
51 x 95
4.22
0.20
1500
51 x 95
4.70
0.20
51 x 115
5.07
0.20
1800
51 x 95
5.15
0.20
51 x 130
5.85
0.20
2200
51 x 130
6.44
0.20
63.5 x 95
6.29
0.20
2700
51 x 130
6.96
0.20
63.5 x 115
7.48
0.20
3300
63.5 x 95
8.22
0.20
63.5 x 130
8.66
0.20
3900
63.5 x 115
9.40
0.20
76 x 115
9.47
0.20
4700
63.5 x 130
10.44
0.20
76 x 130
10.88
0.20
5600
76 x 115
11.92
0.20
76 x 155
12.80
0.20
6800
76 x 155
14.06
0.20
89 x 155
15.00
0.20
8200
89 x 155
16.43
0.20
89 x 155
16.50
0.20
10000
89 x 155
18.28
0.20
89 x 195
20.00
0.20
12000
89 x 195
21.84
0.20
89 x 235
23.61
0.20
15000
89 x 235
26.31
0.20
Note: 1. Ripple Current: (A/rms) 85°C, 120Hz.
2. Dissipation Factor: 120Hz / 20°C
Yageo corporation ELECTROLYTIC CAPACITORS
NM [ For Wide Temperature ]
Screw Type Aluminum
Electrolytic Capacitors
Applicable for Large Power Source, Converter Circuit
ELECTRICAL CHARACTERISTICS
Operating Temperature Range -40 to +105°C
-25 to +105°C
Rated Voltage Range
25 ~ 100V
160 ~ 450V
Rated Capacitance Range
220 ~ 330000μF
Capacitance Tolerance
±20% (120Hz, +20°C)
Leakage Current
I = 0.02CV or 5mA whichever is smaller.
(After 5 Minutes Application of DC Rated Voltage at 20°C)
Dissipation Factor
Description
Less than the Value Specified in the Standard Product Tables
Endurance : 105°C 2000 Hours
at 120Hz, +20°C
Endurance
After the rated voltage has been applied at 105°C for 2000 hours and then
High Ripple Current, Load Life of 2000 hours at 105°C
has resumed its original condition for 16 hours.
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
(a) Capacitance Change: ±20% Initial Measured Value
(b) Dissipation Factor: ≤ 2 Times Initial Specified Value
(c) Leakage Current: ≤ Initial Specified Value
Shelf Life
After having been stored for 1000 hours at 105°C, the rated voltage has
been applied for 30 minutes and then has resumed its original condition for
16 hours.
(a) Capacitance Change: ±20% Initial Measured Value
(b) Dissipation Factor: ≤ 2 Times Initial Specified Value
(c) Leakage Current: ≤ Initial Specified Value
diagram of dimensions
Unit: mm
Sleeve
F
35
12.7
51
22
63.5
28.6
76
32
89
32
M5x0.8
Safety Vent
F ±1
Dø
L ±2
20max
Dø±1
FREQUENCY (Hz) 50
60
100 (120)
FACTOR
0.80
1.00
FREQUENCY (Hz) 300
0.80
1K
≥10K
FACTOR
1.30
1.40
1.10
160
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
25 (32)
SIZE
RIPPLE
CURRENT
35 (44)
DISSIPATION SIZE
FACTOR
RIPPLE
CURRENT
50 (63)
DISSIPATION SIZE
FACTOR
RIPPLE
CURRENT
DISSIPATION
FACTOR
3300
35 x 50
2.20
0.2
4700
35 x 50
3.30
0.25
6800
35 x 50
2.60
0.30
35 x 80
3.40
0.25
10000
35 x 50
2.90
0.35
35 x 80
3.70
0.30
35 x 80
4.10
0.25
15000
35 x 80
4.20
0.35
35 x 80
4.50
0.30
35 x 100
4.90
0.30
22000
35 x 80
5.10
0.35
35 x 100
5.50
0.35
51 x 75
5.90
0.35
33000
35 x 100
6.30
0.40
51 x 75
6.70
0.40
51 x 115
7.80
0.40
47000
51 x 75
8.00
0.40
51 x 95
8.10
0.45
63.5 x 95
9.50
0.40
68000
51 x 115
10.00
0.50
51 x 115
10.00
0.50
63.5 x 115
11.60
0.45
100000
63.5 x 95
11.30
0.60
63.5 x 115
12.10
0.60
76 x 115
14.10
0.50
150000
63.5 x 115
12.90
0.80
76 x 115
13.80
0.70
89 x 130
18.90
0.50
220000
76 x 115
14.80
1.00
89 x 130
17.60
0.70
330000
89 x 130
19.90
1.00
Note: 1. Ripple Current: (A/rms) 105°C, 120Hz
2. Dissipation Factor: 120Hz / 20°C
161
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
63 (79)
SIZE
RIPPLE
CURRENT
80 (100)
DISSIPATION SIZE
FACTOR
RIPPLE
CURRENT
100 (125)
DISSIPATION SIZE
FACTOR
RIPPLE
CURRENT
DISSIPATION
FACTOR
1000
35 x 50
1.40
0.15
1500
35 x 50
1.70
0.15
2200
35 x 50
2.10
0.15
35 x 50
2.10
0.15
35 x 80
2.50
0.15
3300
35 x 50
2.20
0.20
35 x 80
3.00
0.15
35 x 80
3.00
0.15
4700
35 x 80
3.10
0.20
35 x 80
3.60
0.15
35 x 100
3.90
0.15
6800
35 x 80
3.70
0.20
35 x 100
4.00
0.20
51 x 75
5.00
0.15
10000
35 x 100
4.40
0.25
51 x 75
5.20
0.20
51 x 95
6.50
0.15
15000
51 x 75
5.70
0.25
51 x 95
6.20
0.25
63.5 x 95
7.60
0.20
22000
51 x 95
6.80
0.30
63.5 x 95
8.20
0.25
76 x 95
9.70
0.20
33000
63.5 x 95
9.20
0.30
76 x 95
9.70
0.30
76 x 130
11.80
0.25
47000
63.5 x 115
10.90
0.35
76 x 115
12.50
0.30
89 x 130
15.00
0.25
68000
76 x 115
13.00
0.40
89 x 130
16.40
0.30
100000
89 x 130
17.20
0.40
Note: 1. Ripple Current: (A/rms) 105°C, 120Hz
2. Dissipation Factor: 120Hz / 20°C
162
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
160 (200)
SIZE
RIPPLE
CURRENT
200 (250)
DISSIPATION SIZE
FACTOR
330
RIPPLE
CURRENT
250 (300)
DISSIPATION SIZE
FACTOR
RIPPLE
CURRENT
DISSIPATION
FACTOR
35 x 50
0.80
0.15
35 x 50
0.80
0.15
470
35 x 50
1.00
0.15
35 x 50
1.00
0.15
35 x 50
1.00
0.15
680
35 x 50
1.10
0.15
35 x 50
1.10
0.15
35 x 80
1.40
0.15
1000
35 x 80
1.70
0.15
35 x 80
1.70
0.15
35 x 100
1.90
0.15
1500
35 x 80
2.00
0.15
35 x 100
2.20
0.15
51 x 75
2.30
0.15
2200
35 x 100
2.70
0.15
51 x 75
2.80
0.15
51 x 95
3.10
0.15
3300
51 x 80
3.50
0.15
51 x 95
3.70
0.15
63.5 x 95
4.20
0.15
4700
51 x 95
4.40
0.15
63.5 x 95
4.90
0.15
63.5 x 115
5.40
0.15
6800
63.5 x 95
5.90
0.15
63.5 x 115
6.30
0.15
76 x 115
6.90
0.15
10000
76 x 95
7.60
0.15
76 x 115
8.10
0.15
76 x 155
9.30
0.15
15000
76 x 130
10.30
0.15
89 x 130
10.90
0.15
89 x 155
12.20
0.15
22000
89 x 130
13.20
0.15
Note: 1. Ripple Current: (A/rms) 105°C, 120Hz
2. Dissipation Factor: 120Hz / 20°C
163
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
400 (450)
SIZE
RIPPLE
CURRENT
DISSIPATION
FACTOR
450 (500)
SIZE
RIPPLE
CURRENT
DISSIPATION
CURRENT
220
35 x 50
1.10
0.15
330
35 x 100
1.50
0.15
470
51 x 80
2.10
0.15
680
51 x 95
2.70
0.15
51 x 100
4.20
0.15
51 x 130
5.70
0.15
63.5 x 115
7.30
0.15
76 x 130
10.10
0.15
76 x 155
12.60
0.15
89 x 155
15.80
0.15
1000
51 x 75
2.50
0.15
1200
51 x 95
3.00
0.15
1500
51 x 115
3.60
0.15
1800
51 x 130
4.10
0.15
2200
63.5 x 95
4.50
0.15
2700
63.5 x 115
5.30
0.15
3300
63.5 x 130
6.20
0.15
3900
63.5 x 155
7.20
0.15
76 x 115
6.80
0.15
63.5 x 195
8.70
0.15
76 x 130
7.80
0.15
63.5 x 195
9.60
0.15
76 x 155
9.20
0.15
6800
89 x 155
10.70
0.15
8200
89 x 155
11.80
0.15
10000
89 x 195
14.10
0.15
4700
5600
Note: 1. Ripple Current: (A/rms) 105°C, 120Hz
2. Dissipation Factor: 120Hz / 20°C
Yageo corporation ELECTROLYTIC CAPACITORS
Screw Type Aluminum
Electrolytic Capacitors
NF [ Long Life for Inverter ]
Specially For Higher Voltage with Compact Size
ELECTRICAL CHARACTERISTICS
Operating Temperature Range -40 to +85°C
Rated Voltage Range
400V, 450V
Rated Capacitance Range
1800 ~ 22000μF
Capacitance Tolerance
±20% (120Hz, +20°C)
Leakage Current
I = 0.01CV or 5mA Whichever is smaller.
(After 5 Minutes Application of DC Voltage at 20°C)
Description
Endurance : 85°C, 5000 Hours
Higher voltage with compact size, to be used in inverters.
Dissipation Factor
Rate Voltage (V)
400
450
at 120Hz, +20°C
tan δ
0.15
0.15
Endurance
After the rated voltage has been applied at 85°C for 5000 hours, and then
has resumed its original condition for 16 hours.
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FACTOR
60
(b) Dissipation Factor: ≤ 1.75 Times Initial Specified Value
100(120) 300 1K ≥10K
0.70 0.70 1.00
1.10 1.30 1.40
(c) Leakage Current: ≤ Initial Specified Value
Shelf Life
After having been stored for 1000 hours at 85°C, the rated voltage has
been applied for 30 minutes, and then has resumed its original condition for
16 hours.
(a) Capacitance Change: ±15% Initial Measured Value
(b) Dissipation Factor: ≤ 1.75 Times Initial Specified Value
(c) Leakage Current: ≤ Initial Specified Value
diagram of dimensions
Sleeve
M5x0.8
Safety Vent
F ±1
FREQUENCY (Hz) 50
(a) Capacitance Change: ±15% Initial Measured Value
L ±2
20max
Dø±1
Unit: mm
Dø
F
51
22
63.5
28.6
76
32
89
32
101
41.5
165
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
400 (450)
SIZE
RIPPLE
CURRENT
DISSIPATION
FACTOR
1800
450 (500)
SIZE
RIPPLE
CURRENT
DISSIPATION
FACTOR
51 x 115
7.60
0.15
2200
51 x 115
8.80
0.15
51 x 130
8.80
0.15
2700
51 x 130
10.20
0.15
63.5 x 95
9.50
0.15
3300
63.5 x 95
11.00
0.15
63.5 x 115
11.20
0.15
3900
63.5 x 115
12.80
0.15
63.5 x 130
12.80
0.15
4700
63.5 x 130
14.80
0.15
76 x 115
14.10
0.15
5600
76 x 115
16.20
0.15
76 x 130
16.20
0.15
6800
76 x 130
18.70
0.15
76 x 155
19.10
0.15
8200
76 x 155
22.00
0.15
76 x 195
23.00
0.15
89 x 130
21.00
0.15
89 x 170
25.70
0.15
89 x 195
29.70
0.15
101 x 175
29.30
0.15
89 x 235
35.90
0.15
101 x 195
34.20
0.15
101 x 235
40.20
0.15
10000
12000
15000
76 x 195
26.70
0.15
89 x 130
24.20
0.15
89 x 155
28.50
0.15
89 x 195
34.80
0.15
18000
89 x 235
41.20
0.15
22000
101 x 235
47.00
0.15
Note: 1. Ripple Current: (A/rms) 85°C, 120Hz
2. Dissipation Factor: 120Hz / 20°C
Yageo corporation ELECTROLYTIC CAPACITORS
Screw Type Aluminum
Electrolytic Capacitors
NH [ High Temperature, Long Life for Inverter ]
High Ripple Current Products
ELECTRICAL CHARACTERISTICS
Operating Temperature Range -40 to +105°C
-25 to +105°C
Rated Voltage Range
10 ~ 100V
160 ~ 500V
Rated Capacitance Range
330 ~ 390000μF
Capacitance Tolerance
±20% (120Hz, +20°C)
Leakage Current
I = 0.02CV or 5mA whichever is smaller.
(After 5 Minutes Application of DC Voltage at 20°C)
Description
Temperature Characteristics
Endurance : 105°C 5000 Hours
Ur (V)
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
50
10K 50K
10~50V
0.95 1.00 1.05 1.09 1.12
63~100V
0.90 1.00 1.10 1.18 1.22
100~250V
0.80 1.00 1.22 1.30 1.33
350~500V
0.80 1.00 1.50 1.60 1.70
Endurance
160~500
-
8
Z -40°C / Z +20°C
12
-
After the rated voltage has been applied at 105°C for 5000 hours and then
has resumed its original condition for 16 hours.
(a) Capacitance Change: ±20% Initial Measured Value
(b) Dissipation Factor: ≤ 2 Times Initial Specified Value
(c) Leakage Current: ≤ Initial Specified Value
Shelf Life
After having been stored for 1000 hours at 105°C, the rated voltage has
been applied for 30 minutes and then has resumed its original condition for
16 hours.
(a) Capacitance Change: ±20% Initial Measured Value
(b) Dissipation Factor: ≤ 2 Times Initial Specified Value
(c) Leakage Current: ≤ Initial Specified Value
diagram of dimensions
Unit: mm
Hexagonal
Headed Bolt
Sleeve
Bottom
Plate
L±α max
1±1
Dø+2 max
FREQUENCY (Hz)
10~100
Z -25°C /Z +20°C
W±1
120 1K
Impedance Ratio at 120Hz
Dø
W
I
α
NOMINAL DIA.
OF BOLT
51
22
6
3
M5
63.5
28.6 6
3
M5
76
31.8 6
3
M5
89
31.8 6
3
M5
167
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP.
RATED VOLTAGE W V (SURGE VOLTAGE W V)
(μF)
10 (13)
SIZE
16 (20)
RIPPLE
DISSIPATION SIZE
CURRENT FACTOR
25 (32)
RIPPLE
DISSIPATION SIZE
CURRENT FACTOR
D x L: mm
35 (44)
RIPPLE
DISSIPATION SIZE
CURRENT FACTOR
RIPPLE
DISSIPATION
CURRENT FACTOR
8200
35 x 80
3.0
0.30
10000
35 x 80
3.3
0.30
12000
35 x 80
3.3
0.35
35 x 80
3.6
0.30
15000
35 x 50
2.9
0.45
35 x 80
3.7
0.35
35 x 80
4.1
0.30
18000
35 x 80
3.5
0.45
35 x 80
4.0
0.35
35 x 100 4.8
0.30
22000
35 x 80
3.9
0.45
35 x 80
4.5
0.35
35 x 120 5.2
0.35
27000
35 x 80
4.3
0.45
35 x 80
4.3
0.45
35 x 100 5.0
0.40
51 x 80
5.9
0.40
33000
35 x 80
4.7
0.45
35 x 100 4.8
0.50
35 x 120 5.9
0.40
51 x 100 6.6
0.40
39000
35 x 80
5.3
0.45
35 x 100 5.3
0.50
51 x 80
6.5
0.40
51 x 120 7.8
0.40
47000
35 x 100 6.1
0.45
35 x 120 6.2
0.50
51 x 100 7.9
0.40
51 x 120 8.0
0.45
56000
35 x 100 6.2
0.50
51 x 80
6.3
0.60
51 x 120 8.8
0.40
63.5 x 100 9.2
0.45
68000
35 x 120 6.8
0.60
51 x 100 7.6
0.60
51 x 120 9.1
0.50
63.5 x 120 11.0
0.45
82000
51 x 80
7.8
0.60
51 x 120 8.3
0.70
63.5 x 100 10.6
0.50
76 x 120 12.7
0.50
100000 51 x 100 8.5
0.70
51 x 120 9.2
0.70
63.5 x 120 11.4
0.60
76 x 140 13.5
0.60
120000 51 x 100 9.5
0.70
63.5 x 100 9.9
0.80
76 x 100 12.8
0.60
89 x 140 16.1
0.60
150000 63.5 x 100 11.0
0.80
76 x 100 12.3
0.80
76 x 120 13.7
0.75
180000 63.5 x 100 12.1
0.80
76 x 120 14.5
0.80
76 x 140 16.1
0.76
220000 76 x 100 13.2
1.00
76 x 140 15.2
1.00
89 x 140 16.6
1.00
270000 76 x 120 14.4
1.20
89 x 140 16.8
1.20
330000 76 x 140 17.0
1.20
390000 89 x 140 18.6
1.40
Note: 1. Max. Allowable Ripple Current: (A/rms) 105°C, 120Hz
2. Dissipation Factor: 120Hz / 20°C
168
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP.
RATED VOLTAGE W V (SURGE VOLTAGE W V)
(μF)
50 (63)
SIZE
63 (79)
RIPPLE
DISSIPATION SIZE
CURRENT FACTOR
D x L: mm
80 (100)
100 (125)
RIPPLE
DISSIPATION SIZE
RIPPLE
DISSIPATION SIZE
RIPPLE
DISSIPATION
CURRENT FACTOR
CURRENT FACTOR
CURRENT FACTOR
1200
35 x 50
1.4
0.15
1500
35 x 80
1.6
0.15
1800
35 x 80
1.8
0.15
2200
35 x 50
1.9
0.15
35 x 80
2.0
0.15
2700
35 x 50
1.9
0.19
35 x 80
2.2
0.15
35 x 80
2.4
0.15
3300
35 x 50
2.1
0.15
35 x 80
2.5
0.15
35 x 100 2.8
0.15
3900
35 x 50
2.0
0.20
35 x 80
2.7
0.20
35 x 80
2.9
0.15
35 x 120 3.1
0.15
4700
35 x 50
2.2
0.25
35 x 80
2.9
0.20
35 x 100 3.1
0.15
51 x 80
3.6
0.15
5600
35 x 80
2.8
0.25
35 x 80
3.2
0.20
35 x 100 3.6
0.15
51 x 100 4.3
0.15
6800
35 x 80
3.0
0.25
35 x 80
3.5
0.20
35 x 120 4.1
0.20
51 x 120 5.0
0.15
8200
35 x 80
3.3
0.25
35 x 100 4.2
0.25
51 x 80
4.8
0.20
51 x 120 5.5
0.15
10000
35 x 80
3.7
0.25
35 x 120 4.3
0.25
51 x 100 5.6
0.20
63.5 x 100 6.4
0.15
12000
35 x 100 4.4
0.25
51 x 80
4.8
0.25
51 x 100 6.1
0.20
63.5 x 120 6.6
0.20
15000
35 x 120 4.7
0.30
51 x 100 5.9
0.25
51 x 120 7.4
0.20
76 x 100 7.5
0.20
18000
51 x 80
4.8
0.35
51 x 120 6.3
0.30
63.5 x 120 8.0
0.25
76 x 120 8.0
0.25
22000
51 x 100 5.9
0.35
51 x 120 6.7
0.30
76 x 100 9.1
0.25
76 x 140 9.4
0.25
27000
51 x 120 7.0
0.35
63.5 x 120 8.8
0.30
76 x 120 9.7
0.30
89 x 140 10.4
0.30
33000
63.5 x 100 7.6
0.40
76 x 120 10.0
0.35
76 x 140 11.5
0.30
39000
63.5 x 120 8.9
0.40
76 x 140 12.5
0.35
89 x 140 12.5
0.30
47000
63.5 x 120 9.8
0.40
89 x 140 13.8
0.40
56000
76 x 120 11.9
0.40
68000
76 x 140 13.1
0.45
82000
89 x 140 14.8
0.50
Note: 1. Max. Allowable Ripple Current: (A/rms) 105°C, 120Hz
2. Dissipation Factor: 120Hz / 20°C
169
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
D x L: mm
CAP.
RATED VOLTAGE W V (SURGE VOLTAGE W V)
(μF)
160 (200)
200 (250)
250 (300)
350 (400)
SIZE
RIPPLE
DISSIPATION SIZE
RIPPLE
DISSIPATION SIZE
RIPPLE
DISSIPATION SIZE
RIPPLE
DISSIPATION
CURRENT FACTOR
CURRENT FACTOR
CURRENT FACTOR
CURRENT FACTOR
330
35 x 50
0.7
0.15
390
35 x 80
0.8
0.15
470
35 x 50
0.9
0.15
35 x 80
0.9
0.15
560
35 x 80
1.0
0.15
35 x 80
1.0
0.15
680
35 x 50
1.1
0.15
35 x 80
1.1
0.15
35 x 100 1.2
0.15
820
35 x 80
1.2
0.15
35 x 80
1.3
0.15
35 x 100 1.4
0.15
1000
35 x 80
1.3
0.15
35 x 80
1.5
0.15
35 x 120 1.6
0.15
1200
35 x 80
1.5
0.15
35 x 100 1.7
0.15
51 x 80
1.8
0.15
1500
35 x 80
1.7
0.15
35 x 120 1.9
0.15
51 x 100 2.2
0.15
1800
35 x 100 2.0
0.15
35 x 120 2.2
0.15
51 x 120 2.6
0.15
2200
35 x 120 2.3
0.15
51 x 80
2.7
0.15
51 x 120 2.8
2700
35 x 120 2.7
0.15
51 x 100 3.2
0.15
63.5 x 100 3.3
51 x 81
3.3
0.25
51 x 90
5.2
0.25
0.15
51 x 100 7.0
0.25
0.15
51 x 130 8.4
0.25
63.5 x 90 8.1
0.25
3300
51 x 100 3.3
0.15
51 x 120 3.5
0.15
63.5 x 120 4.0
0.15
51 x 150 9.9
0.25
3900
51 x 120 3.8
0.15
63.5 x 100 4.0
0.15
76 x 100 4.4
0.15
63.5 x 130 11.5
0.25
76 x 90
10.8
0.25
4700
51 x 120 4.2
0.15
63.5 x 120 4.7
0.15
76 x 120 5.2
0.15
5600
51 x 120 4.7
0.15
76 x 100 5.3
0.15
76 x 140 6.1
0.15
63.5 x 150 14.7
0.25
6800
63.5 x 120 5.7
0.15
76 x 120 6.3
0.15
89 x 140 7.4
0.15
76 x 130 16.8
0.25
8200
76 x 100 6.4
0.20
76 x 140 6.4
0.20
76 x 150 19.6
0.25
10000
76 x 120 6.8
0.20
89 x 140 7.7
0.20
76 x 190 23.0
0.25
12000
76 x 140 7.8
0.20
15000
89 x 140 9.5
0.20
89 x 190 30.6
0.25
89 x 270 43.5
0.25
22000
Note: 1. Max. Allowable Ripple Current: (A/rms) 105°C, 120Hz
2. Dissipation Factor: 120Hz / 20°C
170
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP.
RATED VOLTAGE W V (SURGE VOLTAGE W V)
(μF)
400 (450)
SIZE
RIPPLE
CURRENT
450 (500)
DISSIPATION SIZE
FACTOR
RIPPLE
CURRENT
500 (550)
DISSIPATION SIZE
FACTOR
470
560
680
51 x 80
51 x 80
3.0
2.6
4.7
2200
2700
3300
51 x 110
6.3
0.25
0.25
8200
3.6
0.20
4.0
0.25
51 x 110
4.4
0.20
51 x 110
4.8
0.25
51 x 130
5.2
0.20
63.5 x 90
5.0
0.20
51 x 150
6.3
0.20
63.5 x 110
6.8
0.20
51 x 130
6.4
0.25
63.5 x 90
6.2
0.25
51 x 150
7.6
0.25
63.5 x 90
7.3
0.25
63.5 x 100
7.5
0.25
51 x 150
8.9
0.25
63.5 x 130
8.9
0.25
63.5 x 150
9.6
0.20
63.5 x 110
8.8
0.25
76 x 90
8.4
0.25
76 x 110
9.2
0.20
63.5 x 130
10.5
0.25
63.5 x 150
10.6
0.25
76 x 90
9.9
0.25
76 x 110
10.2
0.25
76 x 130
11.9
0.25
76 x 150
12.7
0.20
89 x 130
11.9
0.20
89 x 190
18.8
0.20
89 x 270
26.8
0.20
63.5 x 150
13.4
0.25
76 x 130
13.9
0.25
76 x 150
14.0
0.25
89 x 130
14.2
0.25
76 x 150
17.9
0.25
76 x 190
17.3
0.25
89 x 130
17.2
0.25
89 x 150
16.7
0.25
76 x 190
20.8
0.25
89 x 150
20.1
0.25
89 x 190
22.8
0.25
89 x 270
32.8
0.25
89 x 190
27.4
0.25
15000
22000
51 x 90
0.25
10000
12000
0.20
7.5
5600
6800
2.4
51 x 130
3900
4700
51 x 80
51 x 90
1500
1800
DISSIPATION
FACTOR
0.25
1000
51 x 90
RIPPLE
CURRENT
0.25
820
1200
D x L: mm
89 x 270
39.4
0.25
Note: 1. Max. Allowable Ripple Current: (A/rms) 105°C, 120Hz
2. Dissipation Factor: 120Hz / 20°C
Yageo corporation ELECTROLYTIC CAPACITORS
NG [ For Low Voltage, Large Capacity ]
Screw Type Aluminum
Electrolytic Capacitors
Low Leakage Current, Small Size and High Ripple Current
ELECTRICAL CHARACTERISTICS
Operating Temperature Range -40 to +85°C
Rated Voltage Range
10 ~ 100V
Rated Capacitance Range
2200 ~ 1000000μF
Capacitance Tolerance
±20% (120Hz, 20°C)
Leakage Current
D = 35mm I ≤ 0.02CV (μA) or 4mA
(at 20°C, after 2 minutes, whichever is smaller.)
Description
D ≥ 51mm I ≤ 0.03CV (μA) or 6mA
(at 20°C, after 2 minutes, whichever is smaller.)
Endurance
Endurance : 85°C 2000 Hours
After the rated voltage has been applied at 85°C for 2000 hours and then
has resumed its original condition for 16 hours.
Low Voltage (≤ 100V), Large Capacitance, Lug or
Screw Type, Low Dissipation Factor
(a) Capacitance Change: ±15% Initial Measured Value
(b) Dissipation Factor: ≤ 2 Times Initial Specified Value
(c) Leakage Current: ≤ Initial Specified Value
Shelf Life
After having been stored for 1000 hours at 85°C and then has resumed its
original condition for 16 hours.
(a) Capacitance Change: ±15% Initial Measured Value
(b) Dissipation Factor: ≤ 2 Times Initial Specified Value
(c) Leakage Current: ≤ Initial Specified Value
diagram of dimensions
L
35
12
50, 60, 80,
100, 120
51
22
80, 100, 120
63.5
28
100, 120, 140
76
32
100, 120, 140
89
32
140
Vlnyl Vent
Safety Sleeve
Sleeve
M5x0.8
Negative
Safety Vent
F ±1
F
F±1
Dø
Unit: mm
L ±2
10max
Dø±1
L ±2
20max
Dø±1
172
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
6.3 (8)
SIZE
RIPPLE
CURRENT
10 (13)
DISSIPATION SIZE
FACTOR
RIPPLE
CURRENT
16 (20)
DISSIPATION SIZE
FACTOR
22000
RIPPLE
CURRENT
DISSIPATION
FACTOR
35 x 50
4.50
0.50
33000
35 x 50
4.20
0.75
35 x 80
6.40
0.50
47000
35 x 80
6.20
0.75
35 x 100
8.20
0.50
68000
35 x 100
8.00
0.75
35 x 120
10.50
0.50
100000
35 x 120
10.40
0.75
51 x 80
10.70
0.75
150000
51 x 80
11.30
1.00
51 x 120
14.80
0.75
220000
51 x 120
15.50
1.00
63.5 x 120
17.00
1.00
330000
63.5 x 120
17.00
1.50
76 x 120
14.80
1.50
470000
76 x 120
21.90
2.00
63.5 x 140
35.00
1.50
76 x 140
30.00
1.50
1000000
63.5 x 140
40.00
Note: 1. Ripple Current: (A/rms) 85°C, 120Hz
2. Dissipation Factor: 120Hz / 20°C
1.50
173
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
25 (32)
SIZE
RIPPLE
CURRENT
35 (44)
DISSIPATION SIZE
FACTOR
RIPPLE
CURRENT
50 (63)
DISSIPATION SIZE
FACTOR
6800
10000
RIPPLE
CURRENT
DISSIPATION
FACTOR
35 x 50
3.60
0.25
35 x 50
4.30
0.25
35 x 60
4.70
0.25
15000
35 x 50
4.40
0.35
35 x 80
6.20
0.25
35 x 80
6.20
0.25
22000
35 x 80
6.30
0.35
35 x 100
8.00
0.25
51 x 80
7.30
0.35
33000
35 x 100
8.30
0.35
51 x 80
9.00
0.35
51 x 80
9.00
0.35
47000
51 x 80
8.90
0.50
51 x 100
11.50
0.35
51 x 100
11.50
0.35
68000
51 x 80
10.80
0.50
51 x 120
14.60
0.35
63.5 x 100
12.70
0.50
100000
51 x 120
14.80
0.50
63.5 x 100
15.40
0.50
76 x 100
16.60
0.50
150000
63.5 x 120
16.20
0.75
76 x 120
21.40
0.50
220000
76 x 120
21.20
0.75
1000000
89 x 140
28.00
0.75
Note: 1. Ripple Current: (A/rms) 85°C, 120Hz
2. Dissipation Factor: 120Hz / 20°C
174
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP. (μF)
D x L: mm
RATED VOLTAGE W V (SURGE VOLTAGE W V)
63 (79)
SIZE
RIPPLE
CURRENT
80 (100)
DISSIPATION SIZE
FACTOR
RIPPLE
CURRENT
100 (125)
DISSIPATION SIZE
FACTOR
RIPPLE
CURRENT
DISSIPATION
FACTOR
2200
35 x 50
2.10
0.25
3300
35 x 80
3.00
0.25
4700
35 x 50
3.00
0.25
35 x 80
3.40
0.25
35 x 100
3.90
0.25
6800
35 x 60
3.90
0.25
35 x 80
4.30
0.25
35 x 120
4.90
0.25
10000
35 x 80
5.10
0.25
35 x 100
4.20
0.25
51 x 80
6.00
0.25
51 x 80
6.00
0.30
15000
51 x 80
6.70
0.35
51 x 100
7.00
0.30
51 x 120
8.30
0.25
22000
51 x 80
7.40
0.35
63.5 x 100
7.80
0.35
63.5 x 120
9.10
0.35
33000
51 x 100
9.70
0.35
76 x 100
10.50
0.40
76 x 120
12.00
0.35
47000
63.5 x 100
10.50
0.50
76 x 120
13.50
0.40
100000
63.5 x 120
13.4
0.50
Note: 1. Ripple Current: (A/rms) 85°C, 120Hz
2. Dissipation Factor: 120Hz / 20°C
YAGEO - A GLOBAL COMPANY
ASIA
Beijing, China
Dongguan, China
Hong Kong, China
Qingdao, China
Tel. +86 10 851 20810
Fax. +86 10 851 20200
Tel. +86 769 8772 0275
Fax. +86 769 8791 0053
Tel. +852 2342 6833
Fax. +852 2342 6588
Tel. +86 157 2525 4907
Fax. +86 512 6825 5568 x 2688
Suzhou, China
Wuhan, China
Saitama, Japan
Kyunggi-Do, Korea
Tel. +86 512 6825 5568
Fax. +86 512 6825 5386
Tel. +86 27 59838939
Fax. +86 27 59838939
Tel. +81 48 795 8953
Fax. +81 48 795 8954
Tel. +82 31 712 4797
Fax. +82 31 712 5866
Kuala Lumpur, Malaysia
Singapore
Taipei, Taiwan
Tel. +60 3 8063 8864
Fax. +60 3 8063 7376
Tel. +65 6244 7800
Fax. +65 6244 4943
Tel. +886 2 2917 7555
Fax. +886 2 2917 4286
EUROPE
Roermond, Benelux
Suresnes, France
Hamburg, Germany
Szombathely, Hungary
Tel. +31 475 385 555
Fax. +31 475 385 589
Tel. +33 1 46 14 87 91
Fax. +33 1 46 14 87 92
Tel. +49 4121 870 189
Fax. +49 4121 870 271
Tel. +36 30 3777 441
Fax. +36 94 517 701
Milan, Italy
Moscow, Russian Federation
Barcelona, Spain
Berkshire, UK
Tel. +39 02 6129 1017
Fax. +39 02 6601 7490
Tel. +7 916 625 92 38
Fax. +7 498 610 07 07
Tel. +34 93 212 3929
Fax. +39 02 6601 7490
Tel. +44 7767 346 607
Fax. +31 475 385 589
NORTH AMERICA
San Jose, U.S.A.
Tel. +1 408 240 6200
Fax. +1 408 240 6201
For more detailed and always up-to-date contact information of sales offices, distributors and representatives, please go to our website at
www.yageo.com
© YAGEO Corporation
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice.
No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights.
Printed in Taiwan
Document order number: YL 100 00124
Date of release: December 2010