Yageo

Yageo corporation ELECTROLYTIC CAPACITORS
CH [ Ultra Low Impedance & High Temperature ]
Surface Mount
Aluminum Electrolytic
125°C 2000 Hours, Ultra Low Impedance High Temperature
ELECTRICAL CHARACTERISTICS
Operation Temperature Range -40 ~ +125°C
Rated Voltage Range
6.3 ~ 50VDC
Rated Capacitance Range
47 ~ 1000μF
Capacitance Tolerance
±20% at 120Hz, 20°C
Leakage Current (Max. 20°C)
I ≤ 0.01CV or 3μA (After Rated Voltage Applied for 2 Minutes)
I = Leakage Current (μA), C=Nominal Capacitance (μF),
feature
V=Rated Voltage (V)
125°C 2,000 hours, higher temperature range, low
profile vertical chip, low impedance
Dissipation Factor (Max.) (tanδ) Shown in the table of standard rating
(120Hz, 20°C)
Low Temperature Stability
W V (V) :
Endurance
Applications: Automatic Mounting and Reflow Soldering
Impedance Ratio (Max.)
6.3
10
16
25
35
50
Z-25°C/Z+20°C :
2
2
2
2
2
2
Z-40°C/Z+20°C :
3
3
3
3
3
3
After the rated voltage has been applied at 125°C for 1000~2000 hours,
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz)
120
COEFFICIENT
0.70 0.80
1K
10K
100K
0.90
1.00
the capacitors shall meet the following requirements.
(a) Capacitance Change: Within ±30% of the Initial Value
(b) Dissipation Factor: Not Exceeding 300% of Specified Value
(c) Leakage Current: Not Exceeding the Specified Value
Shelf Life
Dø :
8 x 6.5ø
≥8 x 10.5ø
Load Life :
1000hrs
2000hrs
After having been placed at 125°C without voltage applied for 1000 hours (500
hours for 8 x 6.5, the capacitors shall meet the same requirements as Endurance.
DIAGRAM OF DIMENSIONS
Dimensions: mm
K
0.3Max.
L
A
H
I
W
P
K
8.0
6.5
8.3
9.5 Max.
3.4
0.65 ± 0.1
2.2 ± 0.2
0.35 --- 0.75
(I)
Dø
H
(P)
øD ± 0.5
(I)
A ± 0.2
+ 0.15
8.0
10.5
8.3
10.0 Max. 3.4
0.90 ± 0.2
3.1 ± 0.2
0.70 ± 0.2
10.0
10.5
10.3
12.0 Max. 3.5
0.90 ± 0.2
4.6 ± 0.2
0.70 ± 0.2
W
( ) Reference Size
L ± 0.3
D ≥ ø8 = L ± 0.5
144
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
CAP.
RATED VOLTAGE W V (SURGE VOLTAGE W V)
(μF)
6.3 (8)
SIZE
D x L: mm
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
10 (13)
SIZE
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
16 (20)
SIZE
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
100
8 x 6.5
100
0.30
0.50
8 x 6.5
100
0.26
0.50
8 x 6.5
100
0.20
0.50
150
8 x 6.5
100
0.30
0.50
8 x 6.5
100
0.26
0.50
8 x 10.5
197
0.20
0.30
220
8 x 6.5
100
0.30
0.50
8 x 10.5
197
0.26
0.30
8 x 10.5
197
0.20
0.30
330
8 x 10.5 197
0.30
0.30
8 x 10.5
197
0.26
0.30
8 x 10.5
197
0.20
0.30
470
8 x 10.5 197
0.30
0.30
10 x 10.5 297
0.26
0.20
10 x 10.5 297
0.20
0.20
680
10 x 10.5 297
0.30
0.20
10 x 10.5 297
0.26
0.20
1000
10 x 10.5 297
0.30
0.20
Note: 1. Ripple Current: (mA/rms) 125°C, 100KHz
2. Dissipation Factor: 20°C, 120Hz
3. ESR: 100KHz / 20°C (Ω Max.)
145
CASE SIZE & PERMISSIBLE RIPPLE CURRENT OF STANDARD PRODUCTS
D x L: mm
CAP.
RATED VOLTAGE W V (SURGE VOLTAGE W V)
(μF)
25 (32)
SIZE
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
35 (44)
SIZE
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
50 (63)
SIZE
RIPPLE
DISSIPATION ESR
CURRENT FACTOR
47
8 x 6.5
100
0.18
0.50
8 x 10.5
197
0.14
0.30
8 x 10.5
133
0.12
0.75
100
8 x 10.5 197
0.18
0.30
8 x 10.5
197
0.14
0.30
10 x 10.5 221
0.12
0.50
150
8 x 10.5 197
0.18
0.30
10 x 10.5 297
0.14
0.20
220
10 x 10.5 297
0.18
0.20
10 x 10.5 297
0.14
0.20
330
10 x 10.5 297
0.18
0.20
Note: 1. Ripple Current: (mA/rms) 125°C, 100KHz
2. Dissipation Factor: 20°C, 120Hz
3. ESR: 100KHz / 20°C (Ω Max.)