Through-hole resistors Zero Ohm Resistors Coating Type Normal Style [ ZOR Series ] SPECIFICATIONS Power Rating 1/6W, 1/4W Maximum Resistance 20mΩ or less Min. Insulation Resistance Min. Dielectric Withstanding Voltage INTRODUCTION Insulation Flammability •Similar to a 1/4W resistor (1/6W size also available) Current Rating Dry 10,000MΩ Wet 100MΩ Atmospheric 500V RMS Reduced 325V RMS Resistor insulation is self extinguishing within 10 Sec. after externally applied flame is removed 10 AMPS at 70°C for 1/4W 8 AMPS at 70°C for 1/6W •Ideal for automatic insertion or Cut and Form •Available in Tape/Reel, Tape/Box and Bulk •Products meet EU-RoHS requirements DERATING CURVE For resistors operated in ambient temperatures above 70°C, power rating must be derated in accordance with the curve below. Rated Load (%) 70 155 °C 100 80 60 40 20 20 40 60 80 Ambient Temperature (°C) 100 120 140 160 DIMENSIONS Unit: mm ød H L øD Single color code: black STYLE DIMENSION Normal L øD H ød ZOR-12 3.3±0.4 1.8±0.3 28±2.0 0.45±0.05 ZOR-25 6.3±0.5 2.3±0.3 28±2.0 0.55±0.05 88 Explanations Of Ordering Code MFR -12 F Code 7 Tolerance T F Code 8 Packing Style Code 9 Temperature Coefficient of Resistance Code 1 - 3 Series Name Code 4 - 6 Power Rating See Index -05= ød0.5mm P= ±0.02 % T = Tape/Box -06 = ød0.6mm A= ±0.05 % R = Tape/Reel - = Base on Spec. -07 = ød0.7mm B= ±0.1 % B = Bulk 52- 100R Code 10 - 12 Forming Type Code 13 - 17 Resistance Value 26- = 26mm 0R1=0.1 52- = 52.4mm 100R=100 A = ±5 ppm/°C 73- = 73mm 10K=10,000 81- = 81mm 10M=10,000,000 -08 = ød0.8mm C= ±0.25% B = ±10 ppm/°C -10 = ød1.0mm D= ±0.5 % C = ±15 ppm/°C 91- = 91mm -14 = ød1.4mm F = ±1 % S = ± 20ppm/°C F = F Type -12 = 1/6W G= ±2 % D = ±25 ppm/°C FK = FK Type -25 = 1/4W J = ±5 % E = ±50 ppm/°C FKK= FKK Type 25S = 1/4WS K= ±10 % F = ±100 ppm/°C FFK= F-form Kink -50 = 1/2W - = Base on Spec. G = ±200 ppm/°C M = M-Type Forming 50S = 1/2WS H = ±250 ppm/°C MB = M-form W/flat 100 = 1W I = ±300 ppm/°C MT = MT Type Forming 1WS = 1WS J = ±350 ppm/°C MR = MR Type 200 = 2W AV = AVIsert 2WS = 2WS PN = PANAsert 204 = 0.4W 207 = 0.6W 300 = 3W 3WS = 3WS 3WM= 3WM 400 = 4W 500 = 5W 5WS = 5WS 5SS = 5WSS 700 = 7W 7WS = 7WS 10A = 10W 20A = 20W 30A = 30W 40A = 40W 50A = 50W 10S = 10WS 15A = 15W 25A= 25W 10B = 100W 25B = 250W EXCEPTION: • Cement series: • JPW series: <Code 8>: Special packing style code B: B ulk with wirewound or metal oxide sub-assembly for resistance value W: Bulk with ceramic based wirewound sub-assembly for resistance value M: Bulk with metal oxide sub-assembly for resistance value F: Bulk with Fiberglass based wirewound sub-assembly for resistance value <Code 10-12>: Without forming code Example: SQP500JB-10R <Code 13-17>: without resistance value code Example: JPW-06-T-52-