CMD95-21SRC/TR10-RP 1.9mm Round Subminiature LED Features • • package in 12mm tape on 7” diameter reel compatible with automatic placement equipment • • • • EIA Std. package mono-color type Pb-free RoHS compliant • • • indicator and backlight for battery driven equipment indicator and backlight for audio and video equipment backlighting in dashboards and switches Applications • small indicator for indoor applications • flat backlight for LCD, switches and symbols • indicator and backlight in office equipment • telecommunication: indicator and backlighting in telephone and fax Device Selection Guide Chip Materials GaAIAs Emitted Color Deep Red Resin Color White Clear Specifications Absolute Maximum Ratings (Ta=25°C) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA Peak Forward Current (Duty 1/20 @1KHz) IFP 80 mA Power Dissipation Pd 1100 mW Operating Temperature Topr -40 ~ +85 °C Storage temperature Tstg -40 ~ +90 °C Electrostatic Discharge ESDHBM 2000 V Soldering Temperature Tsol engineered to light up your design www.vcclite.com Reflow Soldering : 260 °C for 10 sec. Hand Soldering : 350 °C for 3 sec. 1.800.522.5546 02/15 Rev 1 Specifications (cont) Electro-Optical Characteristics (Ta=25°C) Parameter Symbol Min Typ Max Unit Condition Iv 60 100 ------ mcd IF =20mA 2θ1/2 ------ 25 ------ deg IF =20mA Peak Wavelength λp ------ 660 ------ nm IF =20mA Dominant Wavelength λd ------ 643 ------ nm IF =20mA Forward Voltage VF ------ 2.0 2.4 V IF =20mA Reverse Current IR ------ ------ 10 μA VR =5V Luminous Intensity Viewing Angle Note: 1. Tolerance of Luminous Intensity: ±11% 2. Tolerance of Forward Voltage ±0.1V 3. Tolerance of Dominant Wavelength:±1nm Typical Electro-Optical Characteristics Curves engineered to light up your design www.vcclite.com 1.800.522.5546 02/15 Rev 1 Specifications (cont) Package Outline Dimensions Note: The tolerances unless mentioned is ±0.1mm, Unit = mm Reel & Carrier Tape Dimensions engineered to light up your design www.vcclite.com 1.800.522.5546 02/15 Rev 1 Specifications (cont) Loaded Quantity 1000 PCS/reel Note: The tolerances unless mentioned is ±0.1mm, Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Desiccant Label Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30°C or less and 90%RH or less. 2.3 After opening the package: The LED’s floor life is 72 hours under 30°C or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5°C for 24 hours. 3. Soldering Condition engineered to light up your design www.vcclite.com 1.800.522.5546 02/15 Rev 1 Specifications (cont) 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350°C for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. engineered to light up your design www.vcclite.com 1.800.522.5546 02/15 Rev 1