Datasheet - Everlight

SMD  B
23-23B/R6GHBHC-A01/2A
Features
․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment.
․Compatible with infrared and vapor phase reflow solder process.
․Mono-color type.
․Pb-free.
․The product itself will remain within RoHS compliant version.
Description
․The 23-23B SMD LED is much smaller than lead frame type components, thus enable smaller board ize,
higher packing density, reduced storage space and finally smaller equipment to be obtained.
․Besides, lightweight makes them ideal for miniature applications. etc.
Applications
․Telecommunication: indicator and backlighting in telephone and fax.
․Flat backlight for LCD, switch and symbol.
․General use.
1
Copyright © 2010, Everlight All Rights Reserved. Release Date : Jun.16.2014. Issue No: DSE-0008848
Rev.6
www.everlight.com
DATASHEET
SMD  B
23-23B/R6GHBHC-A01/2A
Device Selection Guide
Chip
Type
Chip
Materials
Emitted Color
Resin Color
R6
AlGaInP
Brilliant
Red
GH
InGaN
Brilliant
Green
BH
InGaN
Blue
Water Clear
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
Reverse Voltage
VR
Forward Current
IF
Peak Forward Current
(Duty 1/10 @1KHz)
IFP
Power Dissipation
Pd
Operating Temperature
Storage Temperature
Topr
Tstg
Electrostatic Discharge
ESDHBM
Soldering Temperature
Tsol
Rating
Unit
5
V
R6:25
GH:20
mA
BH:20
R6:60
GH:75
mA
BH:75
R6:60
GH:95
mW
BH:95
-40 ~ +85
℃
-40 ~ +90
℃
R6:2000
GH:150
V
BH:150
Reflow Soldering : 260 ℃ for 10 sec.
Hand Soldering : 350 ℃ for 3 sec.
Electro-Optical Characteristics (Ta=25℃)
Parameter
Symbol
Luminous Intensity
Iv
Viewing Angle
2θ1/2
Peak Wavelength
λ p
Dominant Wavelength
λ d
Spectrum Radiation Bandwidth
△λ
Forward Voltage
VF
Reverse Current
IR
Min.
R6:72
GH:140
BH:45
----R6:----GH:----BH:----R6:----GH:----BH:----R6:----GH:----BH:----R6:1.7
GH:2.7
BH:2.7
R6:----GH:----BH:-----
Typ.
100
200
65
130
632
518
468
624
525
470
20
35
25
2.0
3.3
3.3
-------------
Max.
----------------------------------------------------2.4
3.7
3.7
10
50
50
Unit
Condition
mcd
IF =20mA
deg
IF =20mA
nm
IF =20mA
nm
IF =20mA
nm
IF =20mA
V
IF =20mA
μA
VR =5V
Note:
Tolerance of Luminous Intensity: ±11%
2
Copyright © 2010, Everlight All Rights Reserved. Release Date : Jun.16.2014. Issue No: DSE-0008848
Rev.6
www.everlight.com
DATASHEET
SMD  B
23-23B/R6GHBHC-A01/2A
Typical Electro-Optical Characteristics Curves
R6
3
Copyright © 2010, Everlight All Rights Reserved. Release Date : Jun.16.2014. Issue No: DSE-0008848
Rev.6
www.everlight.com
DATASHEET
SMD  B
23-23B/R6GHBHC-A01/2A
Typical Electro-Optical Characteristics Curves
GH
4
Copyright © 2010, Everlight All Rights Reserved. Release Date : Jun.16.2014. Issue No: DSE-0008848
Rev.6
www.everlight.com
DATASHEET
SMD  B
23-23B/R6GHBHC-A01/2A
Typical Electro-Optical Characteristics Curves
BH
5
Copyright © 2010, Everlight All Rights Reserved. Release Date : Jun.16.2014. Issue No: DSE-0008848
Rev.6
www.everlight.com
DATASHEET
SMD  B
23-23B/R6GHBHC-A01/2A
Package Outline Dimensions
Note: Tolerances unless mentioned ±0.1mm. Unit = mm
6
Copyright © 2010, Everlight All Rights Reserved. Release Date : Jun.16.2014. Issue No: DSE-0008848
Rev.6
www.everlight.com
DATASHEET
SMD  B
23-23B/R6GHBHC-A01/2A
Moisture Resistant Packing Materials
Label Explanation
Pb
EVERLIGHT
CPN :
P N : XXXXXXXXXXXXX
RoHS
XXXXXXXXXXXXX
CAT : XXX
HUE : XXX
REF : XXX
QTY : XXX
‧CPN: Customer’s Product Number
‧P/N: Product Number
‧QTY: Packing Quantity
‧CAT: Luminous Intensity Rank
‧HUE: Chromaticity Coordinates & Dom. Wavelength Rank
‧REF: Forward Voltage Rank
‧LOT No: Lot Number
LOT NO : XXXXXXXXXX
Reference : XXXXXXXX
MADE IN TAIWAN
Reel Dimensions
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
7
Copyright © 2010, Everlight All Rights Reserved. Release Date : Jun.16.2014. Issue No: DSE-0008848
Rev.6
www.everlight.com
DATASHEET
SMD  B
23-23B/R6GHBHC-A01/2A
Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Moisture Resistant Packaging
Label
8
Aluminum moisture-proof bag
Desiccant
Label
Copyright © 2010, Everlight All Rights Reserved. Release Date : Jun.16.2014. Issue No: DSE-0008848
Rev.6
www.everlight.com
DATASHEET
SMD  B
23-23B/R6GHBHC-A01/2A
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection, otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less.
If unused LEDs remain, it should be stored in moisture proof packages.
2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
260°C Max.
10sec. Max.
Above255°C
30sec.Max.
3°C/sec.Max.
6°C/sec.Max.
Pre-heating
Above 217°C
60~150sec.
150~200°C
60~120sec.
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the
soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because
the damage of the product is often started at the time of the hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering
iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will
not be damaged by repairing.
9
Copyright © 2010, Everlight All Rights Reserved. Release Date : Jun.16.2014. Issue No: DSE-0008848
Rev.6
www.everlight.com
DATASHEET
SMD  B
23-23B/R6GHBHC-A01/2A
Application Restrictions
High reliability applications such as military/aerospace, automotive safety/security systems,
and medical equipment may require different product. If you have any concerns, please contact
Everlight before using this product in your application. This specification guarantees the quality
and performance of the product as an individual component. Do not use this product beyond the
specification described in this document.
10
Copyright © 2010, Everlight All Rights Reserved. Release Date : Jun.16.2014. Issue No: DSE-0008848
Rev.6
www.everlight.com