KBL4005 THRU KB4L10 SILICON BRIDGE RECTIFIERS Reverse Voltage - 50 to 1000 Volts KBL FEATURES 0.768(19.5) 0.728(18.5) 0.580(14.7) 0.540(13.7) 0.052(1.3) 0.048(1.2) The plastic package carries Underwriters Laboratory Flammability Classification 94V-0 Ideal for printed circuit boards Low reverse leakage High forward surge current capability High temperature soldering guaranteed: 260 C/10 seconds,0.375”(9.5mm) lead length, 5 lbs. (2.3kg) tension 0.640(16.3) 0.600(15.2) + AC Forward Current - 4.0 Amperes - 0.750 (19.0) MIN. MECHANICAL DATA 0.083 (2.1) Case: Molded plastic body Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: Polarity symbols marked on case Mounting Position: Any Weight:0.22 ounce, 6.21 grams 0.220(5.6) 0.180(4.6) 0.256(6.5) 0.236(6.0) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Single phase half-wave 60Hz,resistive or inductive load,for capacitive load current derate by 20%. MDD Catalog Number Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward TC=50 C(Note 2) output rectified current at TA=50 C(Note 3) Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Rating for Fusing(t<8.3ms) Maximum instantaneous forward voltage drop per birdge element at 4.0A Maximum DC reverse current TA=25 C at rated DC blocking voltage TA=100 C Typical Junction Capacitance (Note 1) Typical Thermal Resistance (Note 2) Operating junction temperature range storage temperature range SYMBOLS VRRM VRMS VDC KBL 4005 50 35 50 KBL 401 100 70 100 KBL 402 200 140 200 I(AV) KBL 404 400 280 400 4.0 3.0 KBL 406 600 420 600 KBL 408 800 560 800 KBL 410 UNITS 1000 700 1000 VOLTS VOLTS VOLTS Amps IFSM 200 Amps I2t 166 A2s VF 1.0 Volts 10 1.0 105 20 -65 to +150 -55 to +150 µA mA pF C/W C C IR CJ RθJA TJ TSTG NOTES: 1.Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts. 2.Unit mounted on 3.0” x 3.0” x 0.11” thick(7.5x7.5x0.3cm) Al. plate. 3.P.C.Board mounted with 0.5” x0.5”(12x12mm) copper pads,0.375”(9.5mm) lead length. MDD ELECTRONIC FIG. 1- FORWARD CURRENT DERATING CURVE 4.0 3.2 2.4 Single Phase Half Wave 60Hz Resistive or inductive Load 1.6 0.8 0 0 25 50 75 100 125 150 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES RATINGS AND CHARACTERISTIC CURVES KBL4005 THRU KBL410 FIG. 2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 200 160 120 80 40 175 0 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 1 10 AMBIENT TEMPERATURE, C 20 10 1 TJ=25 C PULSE WIDTH=300 µs 1%DUTY CYCLE 0.01 0.6 0.8 1.0 1.2 1.4 1.5 FIG. 4-TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT,AMPERES FIG. 3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 0.1 1,000 100 10 TJ=100 C 1 0.1 0.01 INSTANTANEOUS FORWARD VOLTAGE, VOLTS TJ=25 C 0 20 40 60 80 200 20 TJ=25 C TRANSIENT THERMAL IMPEDANCE, C/W 400 FIG. 6-TYPICAL TRANSIENT THERMAL IMPEDANCE 100 10 1 0.1 0.01 0.1 1 10 2 0.1 1.0 10 100 PERCENT OF PEAK REVERSE VOLTAGE,% FIG. 5-TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, pF 100 NUMBER OF CYCLES AT 60 Hz 100 REVERSE VOLTAGE,VOLTS MDD ELECTRONIC t,PULSE DURATION,sec. 100