RS601 THRU RS607 SILICON BRIDGE RECTIFIERS Reverse Voltage - 50 to 1000 Volts Forward Current - 6.0 Amperes RS-6 0.935(23.7) 0.895(22.7) 0.15 x0.23L (3.8 x5.7L) HOLE THRU FEATURES The plastic package carries Underwriters Laboratory Flammability Classification 94V-0 Ideal for printed circuit boards Low reverse leakage High forward surge current capability High temperature soldering guaranteed: 260 C/10 seconds,0.375”(9.5mm) lead length, 5 lbs. (2.3kg) tension 0.300 (7.5) 0.700(17.8) 0.600(16.8) 0.780(19.8) 0.740(18.8) AC 1.0 MIN. (25.4) MECHANICAL DATA 0.052(1.3) DIA. 0.048(1.2) 0.140 (3.5) Case: Molded plastic body Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: Polarity symbols marked on case Mounting: Thru hole for #6 serew,5in.-lbs. torque max. Weight:0.3 ounce, 8.0 grams 0.220(5.6) 0.180(4.6) 0.280(7.1) 0.268(6.8) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Single phase half-wave 60Hz,resistive or inductive load, for capacitive load current derate by 20%. SYMBOLS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward TA=100 C(Note 2) output rectified current at TA=40 C(Note 3) Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Rating for Fusing(t<8.3ms) Maximum instantaneous forward voltage drop per birdge element at 6.0A Maximum DC reverse current TA=25 C at rated DC blocking voltage TA=100 C Typical Junction Capacitance (Note 1) Typical Thermal Resistance Operating junction temperature range storage temperature range VRRM VRMS VDC RS601 RS602 RS603 RS604 RS605 RS606 RS607 UNITS 50 35 50 100 70 100 200 140 200 I(AV) 400 280 400 6.0 6.0 600 420 600 800 560 800 1000 700 1000 VOLTS VOLTS VOLTS Amps IFSM 150.0 Amps I 2t 93 A2 s VF 1.0 Volts IR CJ RqJA TJ TSTG 10 1.0 105 4.7 -65 to +150 -65 to +150 NOTES: 1.Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts. 2.Unit mounted on 2.6” x 1.4” x0.06” thick(6.3x3.5x0.15cm)Al.plate. 3.Unit mounted on P.C. board with 0.5” x 0.5”(12x12mm) copper pads,0.375”(9.5mm) lead length. www.shunyegroup.com uA mA pF C/W C C RATINGS AND CHARACTERISTIC CURVES RS601 THRU RS607 AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1- FORWARD CURRENT DERATING CURVE 4.8 3.6 Single Phase Half Wave 60Hz Resistive or inductive Load 2.4 1.2 0 0 25 50 FIG. 2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT £PEAK FORWARD SURGE CURRENT, AMPERES 6.0 75 100 125 150 250 200 150 100 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 50 175 0 1 10 AMBIENT TEMPERATURE, C FIG. 4-TYPICAL REVERSE CHARACTERISTICS FIG. 3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 1,000 10 1 TJ=25 C PULSE WIDTH=300 ms 1%DUTY CYCLE 0.1 0.01 0.6 0.8 1.0 1.2 1.4 1.5 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT,AMPERES 20 100 TJ=100 C 10 1 0.1 0.01 TJ=25 C 0 INSTANTANEOUS FORWARD VOLEAGE, VOLTS 20 40 60 80 FIG. 6-TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE, C/W FIG. 5-TYPICAL JUNCTION CAPACITANCE 200 20 TJ=25 C 100 10 1 0.1 0.01 0.1 1 10 2 0.1 1.0 10 100 PERCENT OF PEAK REVERSE VOLTAGE,% 400 JUNCTION CAPACITANCE, pF 100 NUMBER OF CYCLES AT 60 Hz 100 REVERSE VOLTAGE,VOLTS www.shunyegroup.com t,PULSE DURATION,sec. 100