RENESAS HD404652S

To all our customers
Regarding the change of names mentioned in the document, such as Hitachi
Electric and Hitachi XX, to Renesas Technology Corp.
The semiconductor operations of Mitsubishi Electric and Hitachi were transferred to Renesas
Technology Corporation on April 1st 2003. These operations include microcomputer, logic, analog
and discrete devices, and memory chips other than DRAMs (flash memory, SRAMs etc.)
Accordingly, although Hitachi, Hitachi, Ltd., Hitachi Semiconductors, and other Hitachi brand
names are mentioned in the document, these names have in fact all been changed to Renesas
Technology Corp. Thank you for your understanding. Except for our corporate trademark, logo and
corporate statement, no changes whatsoever have been made to the contents of the document, and
these changes do not constitute any alteration to the contents of the document itself.
Renesas Technology Home Page: http://www.renesas.com
Renesas Technology Corp.
Customer Support Dept.
April 1, 2003
Cautions
Keep safety first in your circuit designs!
1. Renesas Technology Corporation puts the maximum effort into making semiconductor products better
and more reliable, but there is always the possibility that trouble may occur with them. Trouble with
semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate
measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or
(iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas
Technology Corporation product best suited to the customer's application; they do not convey any
license under any intellectual property rights, or any other rights, belonging to Renesas Technology
Corporation or a third party.
2. Renesas Technology Corporation assumes no responsibility for any damage, or infringement of any
third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or
circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and
algorithms represents information on products at the time of publication of these materials, and are
subject to change by Renesas Technology Corporation without notice due to product improvements or
other reasons. It is therefore recommended that customers contact Renesas Technology Corporation
or an authorized Renesas Technology Corporation product distributor for the latest product information
before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corporation assumes no responsibility for any damage, liability, or other loss
rising from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corporation by various
means, including the Renesas Technology Corporation Semiconductor home page
(http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data, diagrams,
charts, programs, and algorithms, please be sure to evaluate all information as a total system before
making a final decision on the applicability of the information and products. Renesas Technology
Corporation assumes no responsibility for any damage, liability or other loss resulting from the
information contained herein.
5. Renesas Technology Corporation semiconductors are not designed or manufactured for use in a device
or system that is used under circumstances in which human life is potentially at stake. Please contact
Renesas Technology Corporation or an authorized Renesas Technology Corporation product distributor
when considering the use of a product contained herein for any specific purposes, such as apparatus or
systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.
6. The prior written approval of Renesas Technology Corporation is necessary to reprint or reproduce in
whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must be
exported under a license from the Japanese government and cannot be imported into a country other
than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the
country of destination is prohibited.
8. Please contact Renesas Technology Corporation for further details on these materials or the products
contained therein.
HD404654 Series
4-Bit Single-Chip Microcomputer
Rev. 7.0
Sept. 1999
Description
The HD404654 Series is a member of the HMCS400-series of microcomputers designed to increase
program productivity with large-capacity memory. Each microcomputer has a high-precision dual-tone
multi-frequency (DTMF) generator, three timers, serial interface, voltage comparator, and input capture
circuit.
The HD404654 Series includes three chips: the HD404652 with 2 k-word ROM; the HD404654 with 4 kword ROM; and the HD4074654 with 4 k-word PROM (ZTAT version).
The HD4074654 is a PROM version (ZTAT microcomputer). A program can be written to the PROM by
a PROM writer, which can dramatically shorten system development periods and smooth the process from
debugging to mass production. (The ZTAT version is 27256-compatible.)
ZTAT : Zero Turn Around Time. ZTAT is a trademark of Hitachi Ltd.
Features
• 27 I/O pins and 5 dedicated input pins
 10 high-current output pins: Six 15-mA sinks and four 10-mA sources
• Three timer/counters
• Eight-bit input capture circuit
• Two timer outputs (including two PWM outputs)
• One event counter input (including one double-edge function)
• One clock-synchronous 8-bit serial interface
• Voltage comparator (2 channels)
• On-chip DTMF generator (fOSC = 400 kHz, 800 kHz, 2 MHz, 3.58 MHz or 4 MHz)
• Built-in oscillators
 Main clock: Ceramic or crystal oscillator (an external clock is also possible)
• Six interrupt sources
 Two by external sources
 Four by internal sources
• Subroutine stack up to 16 levels, including interrupts
HD404654 Series
• Two low-power dissipation modes
 Standby mode
 Stop mode
• One external input for transition from stop mode to active mode
• Instruction cycle time: 1 µs (fOSC = 4 MHz at 1/4 division ratio)
 1/4 or 1/32 division ratio can be selected by hardware
• Two operating modes
 MCU mode
 MCU/PROM mode (HD4074654)
Ordering Information
Type
Product Name
Mask ROM HD404652
Model Name
ROM (Words)
RAM (digit)
Package
HD404652H
2,048
512
FP-44A
HD404652S
HD404654
HD404654H
DP-42S
4,096
HD404654S
ZTAT
HD4074654
HD4074654H
HD4074654S
2
FP-44A
DP-42S
4,096
FP-44A
DP-42S
HD404654 Series
Pin Arrangement
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
DP-42S
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
VCC
SEL
R43 /SO1
R42 /SI 1
R41 /SCK1
R40 /EVND
R33
R32 /TOD
R31 /TOC
R30
R23
R22
R21
R20
R13
R12
R11
R10
R00 /INT1
D13 /INT0
D12 /STOPC
FP-44A
33
32
31
30
29
28
27
26
25
24
23
12
13
14
15
16
17
18
19
20
21
22
1
2
3
4
5
6
7
8
9
10
11
R40 /EVND
R33
R32 /TOD
R31 /TOC
R30
R23
R22
R21
R20
R13
R12
D5
D6
D7
D8
D9
D12 /STOPC
D 13 /INT0
R0 0/INT1
R10
R11
NC
RE0/VCref
TEST
OSC1
OSC2
RESET
GND
D0
D1
D2
D3
D4
44
43
42
41
40
39
38
37
36
35
34
NC
VTref
TONER
TONEC
RD1 /COMP 1
RD0 /COMP 0
VCC
SEL
R4 3 /SO 1
R4 2 /SI 1
R4 1 /SCK 1
RD 0 /COMP0
RD 1 /COMP1
TONEC
TONER
VTref
RE 0 /VCref
TEST
OSC1
OSC2
RESET
GND
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
(top view)
3
HD404654 Series
Pin Description
Pin Number
Item
Symbol
DP-42S
FP-44A
Power supply
VCC
42
38
Applies power voltage
GND
11
6
Connected to ground
Test
TEST
7
2
I
Used for factory testing only: Connect this pin to
VCC
Reset
RESET
10
5
I
Resets the MCU
Oscillator
OSC 1
8
3
I
OSC 2
9
4
O
D0–D 9
12–21
7–16
I/O
Input/output pins addressed by individual bits;
pins D 4–D 9 are high-current sink pins that can
each supply up to 15 mA, D 0– D3 are largecurrent source pins that can each supply up to 10
mA
D12, D13
22, 23
17, 18
I
Input pins addressable by individual bits
R0 0–R4 3
24–40
19–21,
23–36
I/O
Input/output pins addressable in 4-bit units
RD0, RD1, RE 0 1, 2, 6
39, 40,1
I
Input pins addressable in 4-bit units
Interrupt
INT0, INT1
23, 24
18, 19
I
Input pins for external interrupts
Stop clear
STOPC
22
17
I
Input pin for transition from stop mode to active
mode
Serial
SCK 1
38
34
I/O
Serial clock input/output pin
SI 1
39
35
I
Serial receive data input pin
SO1
40
36
O
Serial transmit data output pin
TOC, TOD
34, 35
30, 31
O
Timer output pins
EVND
37
33
I
Event count input pins
TONER
4
42
O
Output pin for DTMF row signals
TONEC
3
41
O
Output pin for DTMF column signals.
VT ref
5
43
Port
Timer
DTMF
I/O
Function
Reference voltage pin for DTMF signals
Voltage condition is V CC ≥ VTref ≥ GND.
Comparator
Division rate
4
COMP0,
COMP1
1, 2
39, 40
VC ref
6
1
SEL
41
37
I
Analog input pins for voltage comparator
Reference voltage pin for inputting the threshold
voltage of the analog input pin.
I
Input pin for selecting system clock division rate
rate after RESET input or after stop mode
cancellation.
1/4 division rate: Connect it to V CC
1/32 division rate: Connect it to GND
HD404654 Series
GND
V CC
SEL
OSC 2
OSC 1
STOPC
TEST
RESET
Block Diagram
System control
External
interrupt
RAM
(512 × 4 bits)
D port
INT0
INT1
Timer
A
W (2 bits)
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
Source
High
current
pins
Sink
X (4 bits)
SI1
SO1
SCK1
Y (4 bits)
Timer
D
SCI1
VCref
COMP0
COMP1
Comparator
VTref
TONER
TONEC
DTMF
SPY (4 bits)
ALU
CPU
ST
CA
(1 bit) (1 bit)
Internal data bus
TOD
SPX (4 bits)
Internal address bus
EVND
Timer
C
Internal data bus
TOC
RE port RD port R4 port R3 port R2 port R1 port R0 port
D 12
D 13
R00
R10
R11
R12
R13
R2 0
R2 1
R2 2
R2 3
R3 0
R3 1
R3 2
R3 3
R4 0
R4 1
R4 2
R4 3
RD0
RD1
RE 0
A (4 bits)
B (4 bits)
SP (10 bits)
Instruction
decoder PC (14 bits)
ROM
(4,096 × 10 bits)
(2,048 × 10 bits)
: Data bus
: Signal line
5
HD404654 Series
Memory Map
ROM Memory Map
The ROM memory map is shown in figure 1 and described below.
0
$0000
Vector address
15
$000F
16
$0010
Zero-page subroutine
(64 words)
$003F
63
64
$0040
Program & pattern
(HD404652)
2047
$07FF
Program & pattern
(HD404654, HD4074654)
4095
$0FFF
0
JMPL instruction
1 (Jump to RESET, STOPC routine)
JMPL instruction
2
(Jump to INT0 routine)
3
JMPL instruction
4
(Jump to INT1 routine)
5
6
7
8
9
JMPL instruction
(Jump to timer A routine)
10
11
12
13
14
15
JMPL instruction
(Jump to timer C, routine)
Not used
JMPL instruction
(Jump to timer D, routine)
JMPL instruction
(Jump to serial 1 routine)
$0000
$0001
$0002
$0003
$0004
$0005
$0006
$0007
$0008
$0009
$000A
$000B
$000C
$000D
$000E
$000F
Figure 1 ROM Memory Map
Vector Address Area ($0000–$000F): Reserved for JMPL instructions that branch to the start addresses
of the reset and interrupt routines. After MCU reset or an interrupt, program execution continues from the
vector address.
Zero-Page Subroutine Area ($0000–$003F): Reserved for subroutines. The program branches to a
subroutine in this area in response to the CAL instruction.
Pattern Area ($0000–$0FFF): Contains ROM data that can be referenced with the P instruction.
Program Area ($0000–$07FF (HD404652), $0000–$0FFF (HD404654, HD4074654)): Used for
program coding.
RAM Memory Map
The MCU contains a 512-digit × 4-bit RAM area consisting of a memory register area, a data area, and a
stack area. In addition, an interrupt control bits area, special register area, and register flag area are mapped
onto the same RAM memory space as a RAM-mapped register area outside the above areas. The RAM
memory map is shown in figure 2 and described as follows.
6
HD404654 Series
0
$000
RAM-mapped registers
64
Memory registers (MR)
80
$040
$050
Not used
$090
144
0
3
4
5
6
7
8
9
Interrupt control bits area
(PMRA) W
Port mode register A
Serial mode register 1A (SM1A) W
Serial data register 1 lower (SR1L) R/W
Serial data register 1 upper (SR1U) R/W
Timer mode register A
(TMA) W
$000
$003
$004
$005
$006
$007
$008
$009
Not used
Data (432 digits)
$240
576
Not used
960
$3C0
Stack (64 digits)
$3FF
1023
R:
Read only
W:
Write only
R/W: Read/Write
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
(MIS)
Miscellaneous register
Timer mode register C1 (TMC1)
(TRCL/TWCL)
Timer C
(TRCU/TWCU)
Timer mode register D1 (TMD1)
(TRDL/TWDL)
Timer D
(TRDU/TWDU)
Not used
Timer mode register C2 (TMC2)
Timer mode register D2 (TMD2)
Not used
Compare data register
(CDR)
(CER)
Compare enable register
TG mode register
(TGM)
(TGC)
TG control register
W
W
R/W
R/W
W
R/W
R/W
R/W
R/W
R
W
W
W
$00B
$00C
$00D
$00E
$00F
$010
$011
$012
$013
$014
$015
$016
$017
$018
$019
$01A
$01B
Not used
31
32
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
Register flag area
Port mode register B
(PMRB)
(PMRC)
Port mode register C
Not used
W
W
Detection edge select register 2 (ESR2)
W
W
W
W
Serial mode register 1B
(SM1B)
System clock select register 1 (SSR1)
System clock select register 2 (SSR2)
Not used
Port D0 to D3 DCR
Port D4 to D 7 DCR
Port D8 and D9 DCR
Not used
Port R0 DCR
Port R1 DCR
Port R2 DCR
Port R3 DCR
Port R4 DCR
(DCD0)
(DCD1)
(DCD2)
W
W
W
(DCR0)
(DCR1)
(DCR2)
(DCR3)
(DCR4)
W
W
W
W
W
$01F
$020
$023
$024
$025
$026
$027
$028
$029
$02A
$02B
$02C
$02D
$02E
$02F
$030
$031
$032
$033
$034
$035
Not used
Two registers are mapped
on the same area.
63
$03F
14 Timer read register C lower (TRCL) R Timer write register C lower (TWCL) W $00E
15 Timer read register C upper (TRCU) R Timer write register C upper (TWCU) W $00F
17 Timer read register D lower (TRDL) R Timer write register D lower (TWDL) W $011
18 Timer read register D upper (TRDU) R Timer write register D upper (TWDU) W $012
Figure 2 RAM Memory Map
7
HD404654 Series
RAM-Mapped Register Area ($000–$03F):
• Interrupt Control Bits Area ($000–$003)
This area is used for interrupt control bits (figure 3). These bits can be accessed only by RAM bit
manipulation instructions (SEM/SEMD, REM/REMD, and TM/TMD). However, note that not all the
instructions can be used for each bit. Limitations on using the instructions are shown in figure 4.
• Special Function Register Area ($004–$01A, $024–$034)
This area is used as mode registers and data registers for external interrupts, serial interface 1,
timer/counters, and the comparator, and as data control registers for I/O ports. The structure is shown in
figures 2 and 5. These registers can be classified into three types: write-only (W), read-only (R), and
read/write (R/W). RAM bit manipulation instructions cannot be used for these registers.
• Register Flag Area ($020–$023)
This area is used for the WDON, and other register flags and interrupt control bits (figure 3). These bits
can be accessed only by RAM bit manipulation instructions (SEM/SEMD, REM/REMD, and
TM/TMD). However, note that not all the instructions can be used for each bit. Limitations on using
the instructions are shown in figure 4.
Memory Register (MR) Area ($040–$04F): Consisting of 16 addresses, this area (MR0–MR15) can be
accessed by register-register instructions (LAMR and XMRA). The structure is shown in figure 6.
Data Area ($090–$23F): 432 digits from $090 to $23F.
Stack Area ($3C0–$3FF): Used for saving the contents of the program counter (PC), status flag (ST), and
carry flag (CA) at subroutine call (CAL or CALL instruction) and for interrupts. This area can be used as a
16-level nesting subroutine stack in which one level requires four digits. The data to be saved and the save
conditions are shown in figure 6.
The program counter is restored by either the RTN or RTNI instruction, but the status and carry flags can
only be restored by the RTNI instruction. Any unused space in this area is used for data storage.
8
HD404654 Series
Bit 3
Bit 2
Bit 1
Bit 0
0
IM0
(IM of INT0)
IF0
(IF of INT0)
RSP
(Reset SP bit)
IE
(Interrupt
enable flag)
$000
1
IMTA
(IM of timer A)
IFTA
(IF of timer A)
IM1
(IM of INT1)
IF1
(IF of INT1)
$001
2
IMTC
(IM of timer C)
IFTC
(IF of timer C)
Not used
Not used
$002
3
IMS1
(IM of serial
interface 1)
IFS1
(IF of serial
interface 1)
IMTD
(IM of timer D)
IFTD
(IF of timer D)
$003
Interrupt control bits area
Bit 3
Bit 2
Bit 1
Bit 0
32
Not used
Not used
WDON
(Watchdog
on flag)
Not used
$020
33
RAME
(RAM enable
flag)
Not used
ICEF
(Input capture
error flag)
ICSF
(Input capture
status flag)
$021
IF:
IM:
IE:
SP:
Interrupt request flag
Interrupt mask
Interrupt enable flag
Stack pointer
Register flag area
Figure 3 Configuration of Interrupt Control Bits and Register Flag Areas
IE
IM
IF
ICSF
ICEF
RAME
RSP
WDON
Not used
SEM/SEMD
REM/REMD
TM/TMD
Allowed
Allowed
Allowed
Not executed
Allowed
Allowed
Not executed
Allowed
Not executed
Allowed
Not executed
Not executed
Inhibited
Inhibited
Inhibited
Note: WDON is reset by MCU reset or by STOPC enable for stop mode cancellation.
If the TM or TDM instruction is executed for the inhibited bits or non-existing bits,
the value in ST becomes invalid.
Figure 4 Usage Limitations of RAM Bit Manipulation Instructions
9
HD404654 Series
Bit 3
Bit 2
$000
$003
: Not used
Interrupt control bits area
R42/SI1
PMRA $004
SM1A $005
Bit 0
Bit 1
R41/SCK1
R43/SO1
Serial transmit clock speed selection 1
SR1L $006
Serial data register 1 (lower digit)
SR1U $007
Serial data register 1 (upper digit)
TMA $008
MIS $00C
TMC1 $00D
Clock source selection (timer A)
*2
*1
SO 1 PMOS control
Interrupt frame period selection
Clock source selection (timer C)
TRCL/TWCL $00E
Timer C register (lower digit)
TRCU/TWCU $00F
Timer C register (upper digit)
TMD1 $010
*1
Clock source selection (timer D)
TRDL/TWDL $011
Timer D register (lower digit)
TRDU/TWDU $012
Timer D register (upper digit)
$013
Timer-C output mode selection
TMC2 $014
TMD2 $015
*3
Timer-D output mode selection
$016
CDR $017
CER $018
TGM $019
TGC $01A
*4
Result of each analog input comparison
*5
TONEC output frequency
*6
*7
$020
TONER output frequency
DTMF enable
Register flag area
$023
R00/INT1
PMRB $024
PMRC $025
D13/INT0
D12/STOPC
R40/EVND
$026
ESR2 $027 EVND detection edge selection
*8
SM1B $028
SSR2 $02A
*9
System clock selection
SSR1 $029
*10
DCD0 $02C
Port D3 DCR Port D2 DCR
Port D1 DCR Port D0 DCR
DCD1 $02D
Port D7 DCR Port D6 DCR
Port D5 DCR Port D4 DCR
DCD2 $02E
Port D9 DCR Port D8 DCR
DCR0 $030
Port R0 0 DCR
DCR1 $031
Port R13 DCR Port R1 2 DCR Port R1 1 DCR Port R1 0 DCR
DCR2 $032
Port R2 3 DCR Port R2 2 DCR Port R2 1 DCR Port R2 0 DCR
DCR3 $033
Port R3 3 DCR Port R3 2 DCR Port R3 1 DCR Port R3 0 DCR
DCR4 $034
Port R4 3 DCR Port R4 2 DCR Port R4 1 DCR Port R4 0 DCR
$03F
Notes:
1. Auto-reload on/off
2. Pull-up MOS control
3. Input capture selection
4. Comparator switch
5. Port/comparator selection
6. TONEC output control
7. TONER output control
8. SO1 output level control in idle states
9. Serial clock source selection 1
10. System clock selection
Figure 5 Special Function Register Area
10
HD404654 Series
Memory registers
MR(0) $040
64
MR(1) $041
65
MR(2) $042
66
MR(3)
$043
67
MR(4)
$044
68
MR(5)
$045
69
MR(6)
$046
70
MR(7)
$047
71
MR(8)
$048
72
MR(9)
$049
73
MR(10) $04A
74
MR(11) $04B
75
MR(12) $04C
76
MR(13) $04D
77
MR(14) $04E
78
MR(15) $04F
79
Stack area
Level 16
Level 15
Level 14
Level 13
Level 12
Level 11
Level 10
Level 9
Level 8
Level 7
Level 6
Level 5
Level 4
Level 3
Level 2
1023 Level 1
960
$3C0
$3FF
Bit 3
Bit 2
Bit 1
Bit 0
1020
ST
PC13
PC 12
PC11
$3FC
1021
PC 10
PC9
PC 8
PC7
$3FD
1022
CA
PC6
PC 5
PC4
$3FE
1023
PC 3
PC2
PC 1
PC0
$3FF
PC13 –PC0 : Program counter
ST: Status flag
CA: Carry flag
Figure 6 Configuration of Memory Registers and Stack Area, and Stack Position
11
HD404654 Series
Functional Description
Registers and Flags
The MCU has nine registers and two flags for CPU operations. They are shown in figure 7 and described
below.
3
Accumulator
Initial value: Undefined, R/W
B register
Initial value: Undefined, R/W
W register
Initial value: Undefined, R/W
0
(A)
3
0
(B)
1
0
(W)
3
X register
Initial value: Undefined, R/W
0
(X)
3
Y register
0
(Y)
Initial value: Undefined, R/W
3
SPX register
Initial value: Undefined, R/W
SPY register
Initial value: Undefined, R/W
0
(SPX)
3
0
(SPY)
0
Carry
Initial value: Undefined, R/W
(CA)
Status
Initial value: 1, no R/W
(ST)
0
13
Program counter
Initial value: 0,
no R/W
0
(PC)
9
Stack pointer
Initial value: $3FF, no R/W
1
5
1
1
1
0
(SP)
Figure 7 Registers and Flags
Accumulator (A), B Register (B): Four-bit registers used to hold the results from the arithmetic logic unit
(ALU) and transfer data between memory, I/O, and other registers.
W Register (W), X Register (X), Y Register (Y): Two-bit (W) and four-bit (X and Y) registers used for
indirect RAM addressing. The Y register is also used for D-port addressing.
12
HD404654 Series
SPX Register (SPX), SPY Register (SPY): Four-bit registers used to supplement the X and Y registers.
Carry Flag (CA): One-bit flag that stores any ALU overflow generated by an arithmetic operation. CA is
affected by the SEC, REC, ROTL, and ROTR instructions. A carry is pushed onto the stack during an
interrupt and popped from the stack by the RTNI instruction—but not by the RTN instruction.
Status Flag (ST): One-bit flag that latches any overflow generated by an arithmetic or compare
instruction, not-zero decision from the ALU, or result of a bit test. ST is used as a branch condition of the
BR, BRL, CAL, and CALL instructions. The contents of ST remain unchanged until the next arithmetic,
compare, or bit test instruction is executed, but become 1 after the BR, BRL, CAL, or CALL instruction is
read, regardless of whether the instruction is executed or skipped. The contents of ST are pushed onto the
stack during an interrupt and popped from the stack by the RTNI instruction—but not by the RTN
instruction.
Program Counter (PC): 14-bit binary counter that points to the ROM address of the instruction being
executed.
Stack Pointer (SP): Ten-bit pointer that contains the address of the stack area to be used next. The SP is
initialized to $3FF by MCU reset. It is decremented by 4 when data is pushed onto the stack, and
incremented by 4 when data is popped from the stack. The top four bits of the SP are fixed at 1111, so a
stack can be used up to 16 levels.
The SP can be initialized to $3FF in another way: by resetting the RSP bit with the REM or REMD
instruction.
Reset
The MCU is reset by inputting a high-level voltage to the RESET pin. At power-on or when stop mode is
cancelled, RESET must be high for at least one tRC to enable the oscillator to stabilize. During operation,
RESET must be high for at least two instruction cycles.
Initial values after MCU reset are listed in table 1.
Interrupts
The MCU has 6 interrupt sources: Two external signals (INT0 , INT1), three timer/counters (timers A, C,
and D), and one serial interface (serial 1).
An interrupt request flag (IF), interrupt mask (IM), and vector address are provided for each interrupt
source, and an interrupt enable flag (IE) controls the entire interrupt process.
Interrupt Control Bits and Interrupt Processing: Locations $000 to $003 and $020 to $021 in RAM are
reserved for the interrupt control bits which can be accessed by RAM bit manipulation instructions.
The interrupt request flag (IF) cannot be set by software. MCU reset initializes the interrupt enable flag
(IE) and the IF to 0 and the interrupt mask (IM) to 1.
13
HD404654 Series
A block diagram of the interrupt control circuit is shown in figure 8, interrupt priorities and vector
addresses are listed in table 2, and interrupt processing conditions for the 11 interrupt sources are listed in
table 3.
An interrupt request occurs when the IF is set to 1 and the IM is set to 0. If the IE is 1 at that point, the
interrupt is processed. A priority programmable logic array (PLA) generates the vector address assigned to
that interrupt source.
The interrupt processing sequence is shown in figure 9 and an interrupt processing flowchart is shown in
figure 10. After an interrupt is acknowledged, the previous instruction is completed in the first cycle. The
IE is reset in the second cycle, the carry, status, and program counter values are pushed onto the stack
during the second and third cycles, and the program jumps to the vector address to execute the instruction
in the third cycle.
Program the JMPL instruction at each vector address, to branch the program to the start address of the
interrupt program, and reset the IF by a software instruction within the interrupt program.
14
HD404654 Series
Table 1 Initial Values After MCU Reset
Item
Abbr.
Initial Value Contents
Program counter
(PC)
$0000
Indicates program execution point
from start address of ROM area
Status flag
(ST)
1
Enables conditional branching
Stack pointer
(SP)
$3FF
Stack level 0
Interrupt enable flag
(IE)
0
Inhibits all interrupts
Interrupt request flag
(IF)
0
Indicates there is no interrupt request
Interrupt mask
(IM)
1
Prevents (masks) interrupt requests
Port data register
(PDR)
All bits 1
Enables output at level 1
Data control register
(DCD0–
DCD2)
All bits 0
Turns output buffer off (to high
impedance)
(DCR0–
DCR4)
All bits 0
Port mode register A
(PMRA)
- - 00
Refer to description of port mode
register A
Port mode register B
(PMRB)
---0
Refer to description of port mode
register B
Port mode register C
bits 3, 1, 0
(PMRC3, 000 PMRC1,
PMRC0)
Refer to description of port mode
register C
Detection edge select
register 2
(ESR2)
00 - -
Disables edge detection
Timer mode register A (TMA)
- 000
Refer to description of timer mode
register A
Timer mode register
C1
(TMC1)
0000
Refer to description of timer mode
register C1
Timer mode register
C2
(TMC2)
- 000
Refer to description of timer mode
register C2
Timer mode register
D1
(TMD1)
0000
Refer to description of timer mode
register D1
Timer mode register
D2
(TMD2)
0000
Refer to description of timer mode
register D2
Serial mode register
1A
(SM1A)
0000
Refer to description of serial mode
register 1A
Serial mode register
1B
(SM1B)
- - X0
Refer to description of serial mode
register 1B
Prescaler S
(PSS)
$000
—
Timer counter A
(TCA)
$00
—
Interrupt
flags/mask
I/O
Timer/counters,
serial interface
15
HD404654 Series
Item
Timer/counters,
serial interface
Abbr.
Initial Value Contents
Timer counter C
(TCC)
$00
—
Timer counter D
(TCD)
$00
—
Timer write register C
(TWCU,
TWCL)
$X0
—
Timer write register D
(TWDU,
TWDL)
$X0
—
000
—
0 - 00
Refer to description of voltage
comparator
Octal counter
Comparator
Compare enable
register
Bit register
Watchdog timer on flag (WDON) 0
Refer to description of timer C
Input capture status
flag
Others
(CER)
(ICSF)
0
Refer to description of timer D
Input capture error flag (ICEF)
0
Refer to description of timer D
Miscellaneous register (MIS)
00 - -
Refer to description of operating
modes, and oscillator circuit
System clock select
register 1 bits 1, 0
(SSR11, 00
SSR10)
System clock select
register 2
(SSR2)
Refer to description of operating
modes, and oscillator circuit
-0--
Notes: 1. The statuses of other registers and flags after MCU reset are shown in the following table.
2. X indicates invalid value. – indicates that the bit does not exist.
16
HD404654 Series
Item
Abbr.
Carry flag
(CA)
Accumulator
(A)
B register
(B)
W register
(W)
X/SPX register
(X/SPX)
Y/SPY register
(Y/SPY)
Status After
Cancellation of Stop
Mode by STOPC Input
Status After
Cancellation of Stop
Mode by MCU Reset
Status After all
Other Types of
Reset
Pre-stop-mode values are not guaranteed; values Pre-MCU-reset values
must be initialized by program
are not guaranteed;
values must be
initialized by program
Serial data register (SRL, SRU)
RAM
RAM enable flag
Pre-stop-mode values are retained
(RAME)
Port mode register (PMRC12)
1 bit 2
1
0
0
Pre-stop-mode values
are retained
0
0
System clock
(SSR13)
select register 1 bit
3
Table 2 Vector Addresses and Interrupt Priorities
Reset/Interrupt
Priority
Vector Address
RESET, STOPC*
—
$0000
INT0
1
$0002
INT1
2
$0004
Timer A
3
$0006
Not used
4
$0008
Timer C
5
$000A
Timer D
6
$000C
Serial 1
7
$000E
Note: * The STOPC interrupt request is valid only in stop mode.
17
HD404654 Series
$ 000,0
IE
INT0 interrupt
Sequence control
• Push PC/CA/ST
• Reset IE
• Jump to vector
address
$ 000,2
IFO
$ 000,3
IMO
Vector
address
Priority control logic
INT1 interrupt
$ 001,0
IF1
$ 001,1
IM1
Timer A interrupt
$ 001,2
IFTA
$ 001,3
IMTA
Not used
Timer C interrupt
$ 002,2
IFTC
$ 002,3
IMTC
Timer D interrupt
$ 003,0
IFTD
$ 003,1
IMTD
$ 003,2
Serial interrupt
IFS1
$ 003,3
IMS1
Note: $m,n is RAM address $m, bit number n.
Figure 8 Interrupt Control Circuit
18
HD404654 Series
Table 3 Interrupt Processing and Activation Conditions
Interrupt Source
Interrupt Control Bit INT0
INT1
Timer A
Timer C
Timer D
Serial 1
IE
1
1
1
1
1
1
IF0 · IM0
1
0
0
0
0
0
IF1 · IM1
*
1
0
0
0
0
IFTA · IMTA
*
*
1
0
0
0
IFTC · IMTC
*
*
*
1
0
0
IFTD · IMTD
*
*
*
*
1
0
IFS1 · IMS1
*
*
*
*
*
1
Note: * Can be either 0 or 1. Their values have no effect on operation.
Instruction cycles
1
2
3
4
5
6
Instruction
execution *
Interrupt
acceptance
Stacking
IE reset
Vector address
generation
Execution of JMPL
instruction at vector address
Execution of
instruction at
start address
of interrupt
routine
Note: * The stack is accessed and the IE reset after the instruction
is executed, even if it is a two-cycle instruction.
Figure 9 Interrupt Processing Sequence
19
HD404654 Series
Power on
RESET = 0?
Yes
No
Interrupt
request?
No
Yes
No
IE = 1?
Yes
Reset MCU
Accept interrupt
Execute instruction
IE ← 0
Stack ← (PC)
Stack ← (CA)
Stack ← (ST)
PC ←(PC) + 1
PC← $0002
Yes
INT0
interrupt?
No
PC← $0004
Yes
INT1
interrupt?
No
PC← $0006
Yes
Timer-A
interrupt?
No
PC ← $000A
Yes
Timer-C
interrupt?
No
PC ← $000C
Yes
Timer-D
interrupt?
No
PC ← $000E
(serial 1 interrupt)
Figure 10 Interrupt Processing Flowchart
20
HD404654 Series
Interrupt Enable Flag (IE: $000, Bit 0): Controls the entire interrupt process. It is reset by the interrupt
processing and set by the RTNI instruction, as listed in table 4.
Table 4 Interrupt Enable Flag (IE: $000, Bit 0)
IE
Interrupt Enabled/Disabled
0
Disabled
1
Enabled
External Interrupts (INT0, INT1): Two external interrupt signals.
External Interrupt Request Flags (IF0, IF1: $000, $001): IF0 and IF1 are set at the falling edge of
signals input to INT 0 and INT1 as listed in table 5.
Table 5 External Interrupt Request Flags (IF0, IF1: $000, $001)
IF0, IF1
Interrupt Request
0
No
1
Yes
External Interrupt Masks (IM0, IM1: $000, $001): Prevent (mask) interrupt requests caused by the
corresponding external interrupt request flags, as listed in table 6.
Table 6 External Interrupt Masks (IM0, IM1: $000, $001)
IM0, IM1
Interrupt Request
0
Enabled
1
Disabled (Masked)
Timer A Interrupt Request Flag (IFTA: $001, Bit 2): Set by overflow output from timer A, as listed in
table 7.
Table 7 Timer A Interrupt Request Flag (IFTA: $001, Bit 2)
IFTA
Interrupt Request
0
No
1
Yes
Timer A Interrupt Mask (IMTA: $001, Bit 3): Prevents (masks) an interrupt request caused by the
timer A interrupt request flag, as listed in table 8.
21
HD404654 Series
Table 8 Timer A Interrupt Mask (IMTA: $001, Bit 3)
IMTA
Interrupt Request
0
Enabled
1
Disabled (Masked)
Timer C Interrupt Request Flag (IFTC: $002, Bit 2): Set by overflow output from timer C, as listed in
table 9.
Table 9 Timer C Interrupt Request Flag (IFTC: $002, Bit 2)
IFTC
Interrupt Request
0
No
1
Yes
Timer C Interrupt Mask (IMTC: $002, Bit 3): Prevents (masks) an interrupt request caused by the
timer C interrupt request flag, as listed in table 10.
Table 10 Timer C Interrupt Mask (IMTC: $002, Bit 3)
IMTC
Interrupt Request
0
Enabled
1
Disabled (Masked)
Timer D Interrupt Request Flag (IFTD: $003, Bit 0): Set by overflow output from timer D, or by the
rising or falling edge of signals input to EVND when the input capture function is used, as listed in table
11.
Table 11 Timer D Interrupt Request Flag (IFTD: $003, Bit 0)
IFTD
Interrupt Request
0
No
1
Yes
Timer D Interrupt Mask (IMTD: $003, Bit 1): Prevents (masks) an interrupt request caused by the
timer D interrupt request flag, as listed in table 12.
22
HD404654 Series
Table 12 Timer D Interrupt Mask (IMTD: $003, Bit 1)
IMTD
Interrupt Request
0
Enabled
1
Disabled (Masked)
Serial Interrupt Request Flags (IFS1: $003, Bit 2): Set when data transfer is completed or when data
transfer is suspended, as listed in table 13.
Table 13
Serial Interrupt Request Flag (IFS1: $003, Bit 2)
IFS1
Interrupt Request
0
No
1
Yes
Serial Interrupt Masks (IMS1: $003, Bit 3): Prevents (masks) an interrupt request caused by the serial
interrupt request flag, as listed in table 14.
Table 14 Serial Interrupt Mask (IMS1: $003, Bit 3)
IMS1
Interrupt Request
0
Enabled
1
Disabled (Masked)
23
HD404654 Series
Operating Modes
The MCU has three operating modes as shown in table 15. The operations in each mode are listed in tables
16 and 17. Transitions between operating modes are shown in figure 11.
Table 15 Operating Modes and Clock Status
Mode Name
Active
Standby
RESET cancellation, SBY instruction
Activation method
Stop
STOP instruction
interrupt request,
STOPC cancellation
in stop mode
Status
System oscillator
Cancellation
method
OP
OP
Stopped
RESET input,
RESET input,
RESET input,
STOP/SBY
instruction
interrupt request
STOPC input in stop
mode
Note: OP implies in operation
Table 16 Operations in Low-Power Dissipation Modes
Function
Stop Mode
Standby Mode
CPU
Reset
Retained
RAM
Retained
Retained
Timer A
Reset
OP
Timer C
Reset
OP
Timer D
Reset
OP
Serial 1
Reset
OP
DTMF
Reset
OP
Comparator
Reset
Stopped
I/O
Reset*
Retained
Notes: OP implies in operation
* Output pins are at high impedance.
24
HD404654 Series
Table 17 I/O Status in Low-Power Dissipation Modes
Output
Input
Standby Mode
Stop Mode
Active Mode
D0–D 9
Retained
High impedance
Input enabled
D12–D 13 , RD0, RD1, RE 0
—
—
Input enabled
R0–R4
Retained or output of
peripheral functions
High impedance
Input enabled
Reset by
RESET input or
by watchdog timer
fOSC: Main oscillation
frequency
fcyc: f OSC/4 or or fOSC /32
(hardware selectable)
ø CPU: System clock
ø PER: Clock for other
peripheral functions
RAME = 0
RESET1
RESET2
STOPC
Active
mode
Standby mode
fOSC: Oscillate
ø CPU: Stop
ø PER: fcyc
RAME = 1
SBY
Interrupt
Stop mode
(TMA3 = 0)
fOSC: Oscillate
ø CPU: fcyc
ø PER: fcyc
STOP
fOSC:
ø CPU:
ø PER:
Stop
Stop
Stop
Figure 11 MCU Status Transitions
Active Mode: All MCU functions operate according to the clock generated by the system oscillators OSC1
and OSC2.
Standby Mode: In standby mode, the oscillators continue to operate, but the clocks related to instruction
execution stop. Therefore, the CPU operation stops, but all RAM and register contents are retained, and the
D or R port status, when set to output, is maintained. Peripheral functions such as interrupts, timers, and
serial interface continue to operate. The power dissipation in this mode is lower than in active mode
because the CPU stops.
The MCU enters standby mode when the SBY instruction is executed in active mode.
Standby mode is terminated by a RESET input or an interrupt request. If it is terminated by RESET input,
the MCU is reset as well. After an interrupt request, the MCU enters active mode and executes the next
instruction after the SBY instruction. If the interrupt enable flag is 1, the interrupt is then processed; if it is
0, the interrupt request is left pending and normal instruction execution continues. A flowchart of
operation in standby mode is shown in figure 12.
25
HD404654 Series
Stop
Standby
Oscillator: Stop
Peripheral clocks: Stop
All other clocks: Stop
Oscillator: Active
Peripheral clocks: Active
All other clocks: Stop
No
RESET = 0?
Yes
No
RESET = 0?
Yes
IF0 • IM0 = 1?
No
No
STOPC = 0?
Yes
IF1 • IM1 = 1?
No
Yes
Yes
IFTA • IMTA
= 1?
No
Yes
RAME = 1
RAME = 0
IFTC •
IMTC = 1?
Yes
No
IFTD •
IMTD = 1?
Yes
No
IFS1 •
IMS1 = 1?
No
Yes
Restart
processor clocks
Restart
processor clocks
Execute
next instruction
No
Reset MCU
IF = 1,
IM = 0, and
IE = 1?
Execute
next instruction
Yes
Accept interrupt
Figure 12 MCU Operation Flowchart
Stop Mode: In stop mode, all MCU operations stop and RAM data is retained. Therefore, the power
dissipation in this mode is the least of all modes. The OSC 1 and OSC2 oscillator stops. The MCU enters
stop mode if the STOP instruction is executed in active mode.
Stop mode is terminated by a RESET input or a STOPC input as shown in figure 13. RESET or STOPC
must be applied for at least one t RC to stabilize oscillation (refer to the AC Characteristics section). When
the MCU restarts after stop mode is cancelled, all RAM contents before entering stop mode are retained,
but the accuracy of the contents of the accumulator, B register, W register, X/SPX register, Y/SPY register,
carry flag, and serial data register cannot be guaranteed.
26
,
HD404654 Series
Stop Mode Cancellation by STOPC: The MCU enters active mode from stop mode by inputting STOPC
as well as by RESET. In either case, the MCU starts instruction execution from the starting address
(address 0) of the program. However, the value of the RAM enable flag (RAME: $021, bit 3) differs
between cancellation by STOPC and by RESET. When stop mode is cancelled by RESET, RAME = 0;
when cancelled by STOPC, RAME = 1. RESET can cancel all modes, but STOPC is valid only in stop
mode; STOPC input is ignored in other modes. Therefore, when the program requires to confirm that stop
mode has been cancelled by STOPC (for example, when the RAM contents before entering stop mode are
used after transition to active mode), execute the TEST instruction on the RAM enable flag (RAME) at the
beginning of the program.
Stop mode
Oscillator
Internal
clock
STOPC
or RESET
tres
STOP instruction execution
tres ≥ tRC (stabilization period)
Figure 13 Timing of Stop Mode Cancellation
27
HD404654 Series
MCU Operation Sequence: The MCU operates in the sequences shown in figures 14 to 16. It is reset by
an asynchronous RESET input, regardless of its status.
The low-power mode operation sequence is shown in figure 16. With the IE flag cleared and an interrupt
flag set together with its interrupt mask cleared, if a STOP/SBY instruction is executed, the instruction is
cancelled (regarded as an NOP) and the following instruction is executed. Before executing a STOP/SBY
instruction, make sure all interrupt flags are cleared or all interrupts are masked.
Power on
RESET = 0?
No
Yes
RAME = 0
MCU
operation
cycle
Reset MCU
Figure 14 MCU Operating Sequence (power on)
28
HD404654 Series
MCU operation
cycle
IF = 1?
No
Instruction
execution
Yes
SBY/STOP
instruction?
Yes
No
IM = 0 and
IE = 1?
Yes
IE ← 0
Stack ← (PC),
(CA),
(ST)
No
Low-power mode
operation cycle
IF:
IM:
IE:
PC:
CA:
ST:
PC ← Next
location
PC ← Vector
address
Interrupt request flag
Interrupt mask
Interrupt enable flag
Program counter
Carry flag
Status flag
Figure 15 MCU Operating Sequence (MCU operation cycle)
29
HD404654 Series
Low-power mode
operation cycle
IF = 1 and
IM = 0?
No
Yes
Stop mode
Standby mode
No
IF = 1 and
IM = 0?
Yes
No
STOPC = 0?
Yes
Hardware NOP
execution
Hardware NOP
execution
RAME = 1
PC ← Next
Iocation
PC ← Next
Iocation
Reset MCU
Instruction
execution
MCU operation
cycle
For IF and IM operation, refer to figure 12.
Figure 16 MCU Operating Sequence (Low-Power Mode Operation)
30
HD404654 Series
Internal Oscillator Circuit
A block diagram of the clock generation circuit is shown in figure 17. As shown in table 18, a ceramic
oscillator or crystal oscillator can be connected to OSC1 and OSC2. The system oscillator can also be
operated by an external clock. Bit 1 (SSR11) of system clock select register 1 (SSR1: $029) and bit 2
(SSR22) of system clock select register 2 (SSR2: $02A) must be selected according to the frequency of the
oscillator connected to OSC1 and OSC2 (figure 18).
Note: If the SSR10, SSR11 and SSR22 setting does not match the oscillator frequency, the DTMF
generator will malfunction.
After RESET input or after stop mode has been cancelled, the division ratio of the system clock can be
selected as 1/4 or 1/32 by setting the SEL pin level.
• 1/4 division ratio: Connect SEL to VCC.
• 1/32 division ratio: Connect SEL to GND.
OSC2
OSC1
System fOSC
oscillator
1/4 or
1/32
division
circuit*
fcyc
tcyc
Timing
generator
circuit
φCPU
φPER
CPU with ROM,
RAM, registers,
flags, and I/O
Peripheral
function
interrupt
Note: * 1/4 or 1/32 division ratio can be selected by pin SEL.
Figure 17 Clock Generation Circuit
31
HD404654 Series
System clock select register 1 (SSR1: $029)
Bit
3
2
1
0
Initial value
—
—
0
0
Read/Write
—
—
W
W
Bit name
Not used Not used SSR11
SSR10
SSR22 SSR11 SSR10
× : Don’t care
System clock selection
0
0
0
400 kHz
0
0
1
800 kHz
0
1
0
2 MHz
0
1
1
4 MHz
1
×
×
3.58 MHz
Figure 18 System Clock Select Register 1
System clock select register 2 (SSR2: $02A)
Bit
3
2
1
0
Initial value
—
0
—
—
Read/Write
—
W
—
—
Bit name
SSR22
Not used SSR22 Not used Not used
System clock selection
0
Selected from 400 kHz, 800 kHz,
2 MHz, 4 MHz *
1
3.58 MHz
Note: * Refer to system clock select register 1 (SSR1) of figure 18.
Figure 19 System Clock Select Register 2
32
HD404654 Series
RE0
TEST
OSC1
OSC2
RESET
GND
GND
Figure 20 Typical Layout of Crystal and Ceramic Oscillators
33
HD404654 Series
Table 18 Oscillator Circuit Examples
Circuit Configuration
External clock operation
Circuit Constants
External
oscillator
OSC 1
Open
OSC 2
Ceramic oscillator
(OSC1, OSC 2)
C1
OSC1
Ceramic
oscillator
Rf
Ceramic oscillator: CSB400P22
(Murata), CSB400P (Murata)
Rf = 1 MΩ ± 20%
C1 = C2 = 220 pF ± 5%
OSC2
C2
GND
Ceramic oscillator: CSB800J122
(Murata), CSB800J (Murata)
Rf = 1 MΩ ± 20%
C1 = C2 = 220 pF ± 5%
Ceramic oscillator: CSA2.00MG
(Murata)
Rf = 1 MΩ ± 20%
C1 = C2 = 30 pF ± 20%
Ceramic oscillator: CSA4.00MG
(Murata)
Rf = 1 MΩ ± 20%
C1 = C2 = 30 pF ± 20%
Ceramic oscillator: CSA3.58MG
(Murata)
Rf = 1 MΩ ± 20%
C1 = C2 = 30 pF ± 20%
Notes: 1. Since the circuit constants change depending on the ceramic oscillator and stray capacitance of
the board, the user should consult with the ceramic oscillator manufacturer to determine the
circuit parameters.
2. Wiring among OSC1, OSC 2, and elements should be as short as possible, and must not cross
other wiring (see figure 20).
34
HD404654 Series
Input/Output
The MCU has 27 input/output pins (D0–D 9, R0 0–R4 3) and 5 input pins (D12, D13, RD0, RD 1, RE0). The
features are described below.
• A maximum current of 15 mA is allowed for each of the pins D 4 to D9 with a total maximum current of
less than 105 mA. In addition, D0–D3 can each act as a 10-mA maximum current source.
• Some input/output pins are multiplexed with peripheral function pins such as for the timers or serial
interface. For these pins, the peripheral function setting is done prior to the D or R port setting.
Therefore, when a peripheral function is selected for a pin, the pin function and input/output selection
are automatically switched according to the setting.
• Input or output selection for input/output pins and port or peripheral function selection for multiplexed
pins are set by software.
• Peripheral function output pins are CMOS output pins. Only the R43/SO1 pin can be set to NMOS opendrain output by software.
• In stop mode, the MCU is reset, and therefore peripheral function selection is cancelled. Input/output
pins are in high-impedance state.
• Pins D0–D3 have built-in pull-down MOSs, and other input/output pins have built-in pull-up MOSs,
which can be individually turned on or off by software.
The I/O buffer configuration is shown in figure 21 and 22, programmable I/O circuits are listed in table 19,
and I/O pin circuit types are shown in table 20.
Table 19 Programmable I/O Circuits
MIS3 (Bit 3 of MIS)
0
DCD, DCR
0
PDR
0
1
1
0
1
1
0
1
0
1
0
1
PMOS —
—
—
On
—
—
—
On
NMOS —
—
On
—
—
—
On
—
Pull-up MOS
—
—
—
—
—
On
—
On
Pull-down MOS
—
—
—
—
On
—
On
—
CMOS buffer
Note: — indicates off status.
35
HD404654 Series
D4–D 9, R port
HLT
Pull-up control signal
VCC
Pull-up
MOS
MIS3
VCC
Buffer control signal
DCD, DCR
Output data
PDR
Input data
Input control signal
Figure 21 I/O Buffer Configuration (with Pull-Up MOS)
D0–D 3 port
Input control signal
Input data
VCC
Buffer control signal
DCD
Output data
PDR
MIS3
Pull-down control signal
HLT
Figure 22 I/O Buffer Configuration (with Pull-Down MOS)
36
HD404654 Series
Table 20-1 Circuit Configurations of I/O Pins
I/O Pin Type
Input/output
pins
Circuit
VCC
Pins
HLT
Pull-up control signal
Buffer control
signal
VCC
MIS3
D4–D 9, R0 0,
R1 0–R1 3, R2 0–R2 3
R3 0–R3 3, R40–R4 2
DCD, DCR
Output data
PDR
Input data
Input control signal
Input control signal
D0–D 3
Input data
VCC
Buffer control signal
DCD
Output data
PDR
MIS3
Pull-down control
signal
HLT
VCC
HLT
VCC
Pull-up control signal
Buffer control
signal
Output data
R4 3
MIS3
DCR
MIS2
PDR
Input data
Input control signal
Input pins
Input data
D12, D13
RD0, RD1, RE 0
Input control signal
37
HD404654 Series
I/O Pin Type
Circuit
Peripheral
Input/
function pins output
pins
VCC
Pins
HLT
VCC
Pull-up control signal
MIS3
Output data
Input data
Peripheral
Output
function pins pins
VCC
SCK1
SCK1
HLT
VCC
Pull-up control signal
Output data
Pull-up control signal
VCC
TOC, TOD
HLT
MIS3
PDR
Input data
Input data
TOC, TOD
MIS3
Output data
Input
pins
MIS2
SO1
HLT
VCC
SO1
MIS3
PMOS control
signal
VCC
SCK 1
SI 1, INT1, EVND
SI1, INT1, EVND
INT0, STOPC
INT0, STOPC
Note: The MCU is reset in stop mode, and peripheral function selection is cancelled. The HLT signal
becomes low, and input/output pins enter high-impedance state.
D Port (D0–D13): Consist of 10 input/output pins and 2 input pins addressed by one bit. D0–D3 are highcurrent sources, D4–D9 are large-current sinks, and D12 and D13 are input-only pins.
Pins D 0–D 9 are set by the SED and SEDD instructions, and reset by the RED and REDD instructions.
Output data is stored in the port data register (PDR) for each pin. All pins D0–D13 are tested by the TD and
TDD instructions.
The on/off statuses of the output buffers are controlled by D-port data control registers (DCD0–DCD2:
$02C–$02E) that are mapped to memory addresses (figure 23).
38
HD404654 Series
Pins D12 and D 13 are multiplexed with peripheral function pins STOPC and INT0, respectively. The
peripheral function modes of these pins are selected by bits 2 and 3 (PMRC2, PMRC3) of port mode
register C (PMRC: $025) (figure 24).
R Ports (R00, R10–R43, RD0, RD1, RE0): 17 input/output pins and 3 input pins addressed in 4-bit units.
Data is input to these ports by the LAR and LBR instructions, and output from them by the LRA and LRB
instructions. Output data is stored in the port data register (PDR) for each pin. The on/off statuses of the
output buffers of the R ports are controlled by R-port data control registers (DCR0–DCR4: $030–$034) that
are mapped to memory addresses (figure 23).
Pin R00 is multiplexed with peripheral pin INT1. The peripheral function mode of this pins is selected by
bit 0 (PMRB0) of port mode register B (PMRB: $024) (figure 25).
Pins R31–R32 are multiplexed with peripheral pins TOC and TOD respectively. The peripheral function
modes of these pins are selected by bits 0–2 (TMC20–TMC22) of timer mode register C2 (TMC2: $014),
and bits 0–3 (TMD20–TMD23) of timer mode register D2 (TMD2: $015) (figures 26, and 27).
Pin R4 0 is multiplexed with peripheral pin EVND. The peripheral function mode of this pins is selected by
bit 1 (PMRC1) of port mode register C (PMRC: $025) (figure 24).
Pins R41–R43 are multiplexed with peripheral pins SCK 1, SI1, and SO1, respectively. The peripheral
function modes of these pins are selected by bit 3 (SM1A3) of serial mode register 1A (SM1A: $005), and
bits 0 and 1 (PMRA0, PMRA1) of port mode register A (PMRA: $004), as shown in figures 28 and 29.
Ports RD0 and RD1 are multiplexed with peripheral function pins COMP0 and COMP1, respectively. The
function modes of these pins are selected by bit 3 (CER3) of the compare enable register (CER: $018), as
shown in figure 30.
Port RE 0 is multiplexed with peripheral function pin VCref. While functioning as VC ref , do not use this pin
as an R port at the same time, otherwise, the MCU may malfunction.
Pull-Up or Pull-Down MOS Transistor Control: A program-controlled pull-up or pull-down MOS
transistor is provided for each input/output pin other than input-only pins D 12 and D 13. The on/off status of
all these transistors is controlled by bit 3 (MIS3) of the miscellaneous register (MIS: $00C), and the on/off
status of an individual transistor can also be controlled by the port data register (PDR) of the corresponding
pin—enabling on/off control of that pin alone (table 19 and figure 31).
The on/off status of each transistor and the peripheral function mode of each pin can be set independently.
How to Deal with Unused I/O Pins: I/O pins that are not needed by the user system (floating) must be
connected to V CC to prevent LSI malfunctions due to noise. These pins must either be pulled up to VCC by
their pull-up MOS transistors or by resistors of about 100 kΩ or pulled down to GND by their pull-down
MOS transistors.
39
HD404654 Series
Data control register
(DCD0 to 2: $02C to $02E)
(DCR0 to 4: $030 to $034)
DCD0, DCD1
Bit
3
2
0
1
Initial value
0
0
0
0
Read/Write
W
W
W
W
Bit name
DCD03,
DCD13
DCD02, DCD01, DCD00,
DCD12 DCD11 DCD10
DCD2
Bit
3
2
Initial value
—
—
0
0
Read/Write
—
—
W
W
Bit name
0
1
Not used Not used DCD21
DCD20
DCR0
Bit
3
2
1
Initial value
—
—
—
0
Read/Write
—
—
—
W
Bit name
0
Not used Not used Not used DCR00
DCR1 to DCR4
Bit
3
2
0
1
Initial value
0
0
0
0
Read/Write
W
W
W
W
Bit name
DCR13– DCR12– DCR11– DCR10–
DCR43 DCR42 DCR41 DCR40
All Bits
CMOS Buffer On/Off Selection
0
Off (high-impedance)
1
On
Correspondence between ports and DCD/DCR bits
Register Name
Bit 3
Bit 2
Bit 1
Bit 0
DCD0
D3
D2
D1
D0
DCD1
D7
D6
D5
D4
DCD2
—
—
D9
D8
DCR0
—
—
—
R00
DCR1
R13
R12
R11
R10
DCR2
R23
R22
R21
R20
DCR3
R33
R32
R31
R30
DCR4
R43
R42
R41
R40
Figure 23 Data Control Registers (DCD, DCR)
40
HD404654 Series
Port mode register C (PMRC: $025)
Bit
3
2
1
0
Initial value
0
0
0
—
Read/Write
W
W
W
—
Bit name
PMRC3 PMRC2*
PMRC1 Not used
PMRC1
R40/EVND mode selection
0
R40
1
EVND
PMRC2
D12/STOPC mode selection
0
D12
1
STOPC
PMRC3
D13/INT0 mode selection
0
D13
1
INT0
Note: * PMRC2 is reset to 0 only by RESET input. When STOPC is input in stop
mode, PMRC2 is not reset but retains its value.
Figure 24 Port Mode Register C (PMRC )
Port mode register B (PMRB: $024)
Bit
3
2
1
0
Initial value
—
—
—
0
Read/Write
—
—
—
W
Bit name
Not used Not used Not used PMRB0
PMRB0
R00/INT1 mode selection
0
R00
1
INT1
Figure 25 Port Mode Register B (PMRB)
41
HD404654 Series
Timer mode register C2 (TMC2: $014)
Bit
3
Initial value
—
0
0
0
Read/Write
—
R/W
R/W
R/W
TMC21
TMC20
Bit name
2
0
1
Not used TMC22
TMC22
TMC21
TMC20
0
0
0
R31
R31 port
1
TOC
Toggle output
0
TOC
0 output
1
TOC
1 output
0
—
Inhibited
TOC
PWM output
1
1
0
R31/TOC mode selection
1
1
0
1
Figure 26 Timer Mode Register C2 (TMC2)
42
HD404654 Series
Timer mode register D2 (TMD2: $015)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
TMD23
TMD22
TMD21
TMD20
Bit name
R32/TOD mode selection
TMD23
TMD22
TMD21
TMD20
0
0
0
0
R32
R32 port
1
TOD
Toggle output
0
TOD
0 output
1
TOD
1 output
0
—
Inhibited
TOD
PWM output
R32
Input capture (R32 port)
1
1
0
1
1
0
1
1
Don’t care Don’t care Don’t care
Figure 27 Timer Mode Register D2 (TMD2)
43
HD404654 Series
Serial mode register 1A (SM1A: $005)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
SM1A3
SM1A2
SM1A1
SM1A0
Bit name
SM1A3
R41/SCK1
mode selection
0
R41
1
SCK1
SM1A2
SM1A1
SM1A0
SCK1
Clock source
Prescaler
division
ratio
0
0
0
Output
Prescaler
÷2048
1
Output
Prescaler
÷512
0
Output
Prescaler
÷128
1
Output
Prescaler
÷32
0
Output
Prescaler
÷8
1
Output
Prescaler
÷2
0
Output
System clock
—
1
Input
External clock
—
1
1
0
1
Figure 28 Serial Mode Register 1A (SM1A)
Port mode register A (PMRA: $004)
Bit
3
2
1
0
Initial value
—
—
0
0
Read/Write
—
—
W
W
Bit name
Not used Not used PMRA1 PMRA0
PMRA0
R43/SO1 mode selection
0
R43
1
SO1
PMRA1
R42/SI1 mode selection
0
R42
1
SI1
Figure 29 Port Mode Register A (PMRA)
44
HD404654 Series
Compare enable register (CER: $018)
Bit
3
2
1
0
Initial value
0
—
0
0
Read/Write
Bit name
CER3
W
—
W
W
CER3
Not used
CER1
CER0
Digital/Analog selection
CER1
CER0
Analog input pin selection
Digital input mode:
RD0 /COMP0 and RD1 /COMP1
operate as an R port.
0
0
COMP0
0
0
1
COMP1
Analog input mode:
RD0 /COMP0 and RD 1 /COMP1
operate as analog input.
1
0
Not used
1
1
1
Not used
Figure 30 Compare Enable Register
Miscellaneous register (MIS: $00C)
Bit
3
2
1
0
Initial value
0
0
—
—
—
—
Read/Write
Bit name
MIS3
W
W
MIS3
MIS2
Pull-up MOS
on/off selection
Not used Not used
MIS2
CMOS buffer
on/off selection
for pin R43/SO1
0
Off
0
On
1
On
1
Off
Figure 31 Miscellaneous Register (MIS)
45
HD404654 Series
Prescalers
The MCU has the following prescaler S.
The prescaler operating conditions are listed in table 21, and the prescaler output supply is shown in figure
32. The timer A–D input clocks except external events and the serial transmit clock except the external
clock are selected from the prescaler outputs, depending on corresponding mode registers.
Prescaler Operation
Prescaler S: 11-bit counter that inputs a system clock signal. After being reset to $000 by MCU reset,
prescaler S divides the system clock. Prescaler S keeps counting, except at MCU reset.
Table 21 Prescaler Operating Conditions
Prescaler
Input Clock
Reset Condition
Stop Conditions
Prescaler S
System clock
MCU reset
MCU reset, stop mode
Timer A
Timer C
System
clock
Prescaler S
Timer D
Serial 1
Figure 32 Prescaler Output Supply
46
HD404654 Series
Timers
The MCU has three timer/counters (A, C, and D).
• Timer A: Free-running timer
• Timer C: Multifunction timer
• Timer D: Multifunction timer
Timer A is an 8-bit free-running timer. Timers C and D are 8-bit multifunction timers, whose functions are
listed in table 22. The operating modes are selected by software.
Table 22 Timer Functions
Functions
Clock source
Timer functions
Timer outputs
Timer A
Timer C
Timer D
Prescaler S
Available
Available
Available
External event
—
—
Available
Free-running
Available
Available
Available
Event counter
—
—
Available
Reload
—
Available
Available
Watchdog
—
Available
—
Input capture
—
—
Available
Toggle
—
Available
Available
0 output
—
Available
Available
1 output
—
Available
Available
PWM
—
Available
Available
Note: — means not available.
47
HD404654 Series
Timer A
Timer A Functions: Timer A has the following functions.
• Free-running timer
The block diagram of timer A is shown in figure 33.
Timer A interrupt
request flag
(IFTA)
Timer
counter A
(TCA) Overflow
Internal data bus
Clock
System
clock
ø PER
÷2
÷4
÷8
÷ 32
÷ 128
÷ 512
÷ 1024
÷ 2048
Selector
Prescaler S (PSS)
3
Timer mode
register A
(TMA)
Figure 33 Block Diagram of Timer A
Timer A Operations:
• Free-running timer operation: The input clock for timer A is selected by timer mode register A (TMA:
$008).
Timer A is reset to $00 by MCU reset and incremented at each input clock. If an input clock is applied
to timer A after it has reached $FF, an overflow is generated, and timer A is reset to $00. The overflow
sets the timer A interrupt request flag (IFTA: $001, bit 2). Timer A continues to be incremented after
reset to $00, and therefore it generates regular interrupts every 256 clocks.
Registers for Timer A Operation: Timer A operating modes are set by the following registers.
• Timer mode register A (TMA: $008): Four-bit write-only register that selects timer A’s operating mode
and input clock source as shown in figure 34.
48
HD404654 Series
Timer mode register A (TMA: $008)
Bit
3
2
1
0
Initial value
—
0
0
0
Read/Write
—
W
W
W
Not used
TMA2
TMA1
TMA0
Bit name
Source
Input clock
TMA2 TMA1 TMA0 prescaler frequency Operating mode
0
0
1
1
0
1
0
PSS
2048tcyc
1
PSS
1024tcyc
0
PSS
512tcyc
1
PSS
128tcyc
0
PSS
32tcyc
1
PSS
8tcyc
0
PSS
4tcyc
1
PSS
2tcyc
Timer A mode
Note: Timer counter overflow output period (seconds) = input clock period (seconds) × 256.
Figure 34 Timer Mode Register A (TMA)
Timer C
Timer C Functions: Timer C has the following functions.
• Free-running/reload timer
• Watchdog timer
• Timer output operation (toggle, 0, 1, and PWM outputs)
The block diagram of timer C is shown in figure 35.
49
HD404654 Series
System
reset signal
Watchdog on
flag (WDON)
TOC
Timer C interrupt
flag (IFTC)
Watchdog timer
control logic
Timer output
control logic
Timer read register CU (TRCU)
Timer output
control
Timer read
register CL
(TRCL)
Timer counter C
(TCC)
Timer write
register CU
(TWCU)
÷2
÷4
÷8
÷32
÷128
÷512
÷1024
÷2048
Selector
System øPER
clock
Prescaler S (PSS)
Overflow
Free-running
/reload control
Timer write
register CL
(TWCL)
Internal data bus
Clock
3
Timer mode
register C1
(TMC1)
3
Timer mode
register C2
(TMC2)
Figure 35 Block Diagram of Timer C
Timer C Operations:
• Free-running/reload timer operation: The free-running/reload operation, input clock source, and
prescaler division ratio are selected by timer mode register C1 (TMC1: $00D).
Timer C is initialized to the value set in timer write register C (TWCL: $00E, TWCU: $00F) by
software and incremented by one at each clock input. If an input clock is applied to timer C after it has
reached $FF, an overflow is generated. In this case, if the reload timer function is enabled, timer C is
initialized to its initial value set in timer write register C; if the free-running timer function is enabled,
the timer is initialized to $00 and then incremented again.
50
HD404654 Series
The overflow sets the timer C interrupt request flag (IFTC: $002, bit 2). IFTC is reset by software or
MCU reset. Refer to figure 3 and table 1 for details.
• Watchdog timer operation: Timer C is used as a watchdog timer for detecting out-of-control program
routines by setting the watchdog on flag (WDON: $020, bit 1) to 1. If a program routine runs out of
control and an overflow is generated, the MCU is reset. Program run can be controlled by initializing
timer C by software before it reaches $FF.
• Timer output operation: The following four output modes can be selected for timer C by setting timer
mode register C2 (TMC2: $014).
 Toggle
 0 output
 1 output
 PWM output
By selecting the timer output mode, pin R31/TOC is set to TOC. The output from TOC is reset low by
MCU reset.
 Toggle output: When toggle output mode is selected, the output level is inverted if a clock is input
after timer C has reached $FF. By using this function and the reload timer function, clock signals
can be output at a required frequency for the buzzer. The output waveform is shown in figure 36.
 PWM output: When PWM output mode is selected, timer C provides the variable-duty pulse output
function. The output waveform differs depending on the contents of timer mode register C1
(TMC1: $00D) and timer write register C (TWCL: $00E, TWCU: $00F). The output waveform is
shown in figure 36.
 0 output: When 0 output mode is selected, the output level is pulled low if a clock is input after
timer C has reached $FF. Note that this function must be used only when the output level is high.
 1 output: When 1 output mode is selected, the output level is set high if a clock is input after timer
C has reached $FF. Note that this function must be used only when the output level is low.
51
HD404654 Series
Toggle output waveform (timers C, and D)
Free-running timer
256 clock cycles
256 clock cycles
(256 – N)
clock cycles
(256 – N)
clock cycles
Reload timer
PWM output waveform (timers C and D)
T × (N + 1)
TMC13 = 0
TMD13 = 0
T
T × 256
TMC13 = 1
TMD13 = 1
T × (256 – N)
Notes: The waveform is always fixed low when N = $FF.
T: Input clock period to counter (figures 37 and 44)
N: The value of the timer write register
Figure 36 Timer Output Waveform
Registers for Timer C Operation: By using the following registers, timer C operation modes are selected
and the timer C count is read and written.




Timer mode register C1 (TMC1: $00D)
Timer mode register C2 (TMC2: $014)
Timer write register C (TWCL: $00E, TWCU: $00F)
Timer read register C (TRCL: $00E, TRCU: $00F)
• Timer mode register C1 (TMC1: $00D): Four-bit write-only register that selects the freerunning/reload timer function, input clock source, and the prescaler division ratio as shown in figure 37.
It is reset to $0 by MCU reset.
52
HD404654 Series
Writing to this register is valid from the second instruction execution cycle after the execution of the
previous timer mode register C1 write instruction. Setting timer C’s initialization by writing to timer
write register C (TWCL: $00E, TWCU: $00F) must be done after a mode change becomes valid.
Timer mode register C1 (TMC1: $00D)
Bit
3
2
0
1
Initial value
0
0
0
0
Read/Write
W
W
W
W
TMC13
TMC12
TMC11
TMC10
Bit name
TMC13
Free-running/reload timer selection
0
Free-running timer
1
Reload timer
Input clock period
TMC12
TMC11
TMC10
0
0
0
2048tcyc
1
1024tcyc
0
512tcyc
1
128tcyc
0
32tcyc
1
8tcyc
0
4tcyc
1
2tcyc
1
1
0
1
Figure 37 Timer Mode Register C1 (TMC1)
• Timer mode register C2 (TMC2: $014): Three-bit read/write register that selects the timer C output
mode as shown in figure 38. It is reset to $0 by MCU reset.
53
HD404654 Series
Timer mode register C2 (TMC2: $014)
Bit
3
2
1
0
Initial value
—
0
0
0
Read/Write
—
R/W
R/W
R/W
Not used TMC22
TMC21
TMC20
TMC22
TMC21
TMC20
0
0
0
R31
R31 port
1
TOC
Toggle output
0
TOC
0 output
1
TOC
1 output
0
—
Inhibited
TOC
PWM output
Bit name
1
1
0
R31/TOC mode selection
1
0
1
1
Figure 38 Timer Mode Register C2 (TMC2)
• Timer write register C (TWCL: $00E, TWCU: $00F): Write-only register consisting of a lower digit
(TWCL) and an upper digit (TWCU) as shown in figures 39 and 40. The lower digit is reset to $0 by
MCU reset, but the upper digit value is invalid.
Timer C is initialized by writing to timer write register C (TWCL: $00E, TWCU: $00F). In this case,
the lower digit (TWCL) must be written to first, but writing only to the lower digit does not change the
timer C value. Timer C is initialized to the value in timer write register C at the same time the upper
digit (TWCU) is written to. When timer write register C is written to again and if the lower digit value
needs no change, writing only to the upper digit initializes timer C.
Timer write register C (lower digit) (TWCL: $00E)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
TWCL3
TWCL2
TWCL1
TWCL0
Bit name
Figure 39 Timer Write Register C Lower Digit (TWCL)
54
HD404654 Series
Timer write register C (upper digit) (TWCU: $00F)
Bit
Initial value
Read/Write
Bit name
3
2
1
0
Undefined Undefined Undefined Undefined
W
W
W
W
TWCU3
TWCU2
TWCU1
TWCU0
Figure 40 Timer Write Register C Upper Digit (TWCU)
• Timer read register C (TRCL: $00E, TRCU: $00F): Read-only register consisting of a lower digit
(TRCL) and an upper digit (TRCU) that holds the count of the timer C upper digit as shown in figures
41 and 42. The upper digit (TRCU) must be read first. At this time, the count of the timer C upper digit
is obtained, and the count of the timer C lower digit is latched to the lower digit (TRCL). After this, by
reading TRCL, the count of timer C when TRCU is read can be obtained.
Timer read register C (lower digit) (TRCL: $00E)
Bit
Initial value
Read/Write
Bit name
3
2
1
0
Undefined Undefined Undefined Undefined
R
R
R
R
TRCL3
TRCL2
TRCL1
TRCL0
Figure 41 Timer Read Register C Lower Digit (TRCL)
Timer read register C (upper digit) (TRCU: $00F)
Bit
Initial value
Read/Write
Bit name
3
2
1
0
Undefined Undefined Undefined Undefined
R
R
R
R
TRCU3
TRCU2
TRCU1
TRCU0
Figure 42 Timer Read Register C Upper Digit (TRCU)
Timer D
Timer D Functions: Timer D has the following functions.
•
•
•
•
Free-running/reload timer
External event counter
Timer output operation (toggle, 0, 1, and PWM outputs)
Input capture timer
The block diagram for each operation mode of timer D is shown in figures 43 (A) and (B).
55
HD404654 Series
Timer D interrupt
request flag (IFTD)
Timer output
control logic
TOD
Timer read
register DU (TRDU)
Timer output
control
Timer read
register DL
(TRDL)
Clock
Timer write
register DU
(TWDU)
System
clock
øPER
÷2048
÷512
÷32
÷8
÷4
÷2
Edge
detection
logic
÷128
Selector
EVND
Overflow
Free-running/
reload control
Timer write
register DL
(TWDL)
3
Prescaler S (PSS)
Timer mode
register D1
(TMD1)
3
Timer mode
register D2
(TMD2)
Edge detection control
2
Edge detection
selection register
2 (ESR2)
Figure 43 (A) Block Diagram of Timer D (Free-Running/Reload Timer)
56
Internal data bus
Timer counter D
(TCD)
HD404654 Series
Input capture
status flag (ICSF)
Input capture
error flag (ICEF)
Timer D interrupt
request flag (IFTD)
Error
control
logic
Timer read
register DU
(TRDU)
Timer read
register DL
(TRDL)
EVND
Edge
detection
logic
Read signal
Clock
Timer counter D
(TCD)
Overflow
System
clock
÷2048
3
÷512
÷128
÷32
÷8
÷4
÷2
Selector
Timer mode
register D1
(TMD1)
Internal data bus
Input capture
timer control
øPER
Prescaler S (PSS)
Timer mode
register D2
(TMD2)
Edge detection control
2
Edge detection
selection register
2 (ESR2)
Figure 43 (B) Block Diagram of Timer D (in Input Capture Timer Mode)
Timer D Operations:
• Free-running/reload timer operation: The free-running/reload operation, input clock source, and
prescaler division ratio are selected by timer mode register D1 (TMD1: $010).
57
HD404654 Series
Timer D is initialized to the value set in timer write register D (TWDL: $011, TWDU: $012) by
software and incremented by one at each clock input. If an input clock is applied to timer D after it has
reached $FF, an overflow is generated. In this case, if the reload timer function is enabled, timer D is
initialized to its initial value set in timer write register D; if the free-running timer function is enabled,
the timer is initialized to $00 and then incremented again.
The overflow sets the timer D interrupt request flag (IFTD: $003, bit 0). IFTD is reset by software or
MCU reset. Refer to figure 3 and table 1 for details.
• External event counter operation: Timer D is used as an external event counter by selecting the
external event input as an input clock source. In this case, pin R40/EVND must be set to EVND by port
mode register C (PMRC: $025).
Either falling or rising edge, or both falling and rising edges of input signals can be selected as the
external event detection edge by detection edge select register 2 (ESR2: $027). When both rising and
falling edges detection is selected, the time between the falling edge and rising edge of input signals
must be 2t cyc or longer.
Timer D is incremented by one at each detection edge selected by detection edge select register 2
(ESR2: $027). The other operation is basically the same as the free-running/reload timer operation.
• Timer output operation: The following four output modes can be selected for timer D by setting timer
mode register D2 (TMD2: $015).
 Toggle
 0 output
 1 output
 PWM output
By selecting the timer output mode, pin R32/TOD is set to TOD. The output from TOD is reset low by
MCU reset.
 Toggle output: The operation is basically the same as that of timer-C’s toggle output.
 0 output: The operation is basically the same as that of timer-C’s 0 output.
 1 output: The operation is basically the same as that of timer-C’s 1 output.
 PWM output: The operation is basically the same as that of timer-C’s PWM output.
• Input capture timer operation: The input capture timer counts the clock cycles between trigger edges
input to pin EVND.
Either falling or rising edge, or both falling and rising edges of input signals can be selected as the
trigger input edge by detection edge select register 2 (ESR2: $027).
When a trigger edge is input to EVND, the count of timer D is written to timer read register D (TRDL:
$011, TRDU: $012), and the timer D interrupt request flag (IFTD: $003, bit 0) and the input capture
status flag (ICSF: $021, bit 0) are set. Timer D is reset to $00, and then incremented again. While
ICSF is set, if a trigger input edge is applied to timer D, or if timer D generates an overflow, the input
capture error flag (ICEF: $021, bit 1) is set. ICSF and ICEF are reset to 0 by MCU reset or by writing
0.
By selecting the input capture operation, pin R3 2/TOD is set to R3 2 and timer D is reset to $00.
58
HD404654 Series
Registers for Timer D Operation: By using the following registers, timer D operation modes are selected
and the timer D count is read and written.






Timer mode register D1 (TMD1: $010)
Timer mode register D2 (TMD2: $015)
Timer write register D (TWDL: $011, TWDU: $012)
Timer read register D (TRDL: $011, TRDU: $012)
Port mode register C (PMRC: $025)
Detection edge select register 2 (ESR2: $027)
• Timer mode register D1 (TMD1: $010): Four-bit write-only register that selects the freerunning/reload timer function, input clock source, and the prescaler division ratio as shown in figure 44.
It is reset to $0 by MCU reset.
Writing to this register is valid from the second instruction execution cycle after the execution of the
previous timer mode register D1 (TMD1: $010) write instruction. Setting timer D’s initialization by
writing to timer write register D (TWDL: $011, TWDU: $012) must be done after a mode change
becomes valid.
When selecting the input capture timer operation, select the internal clock as the input clock source.
Timer mode register D1 (TMD1: $010)
Bit
3
2
0
1
Initial value
0
0
0
0
Read/Write
W
W
W
W
TMD13
TMD12
TMD11
TMD10
Bit name
TMD13
Free-running/reload timer selection
0
Free-running timer
1
Reload timer
Input clock period and
input clock source
TMD12
TMD11
TMD10
0
0
0
2048tcyc
1
512tcyc
0
128tcyc
1
32tcyc
0
8tcyc
1
4tcyc
0
2tcyc
1
R40/EVND (external event input)
1
1
0
1
Figure 44 Timer Mode Register D1 (TMD1)
• Timer mode register D2 (TMD2: $015): Four-bit read/write register that selects the timer D output
mode and input capture operation as shown in figure 45. It is reset to $0 by MCU reset.
59
HD404654 Series
Timer mode register D2 (TMD2: $015)
Bit
3
2
0
1
Initial value
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
TMD23
TMD22
TMD21
TMD20
Bit name
TMD23
TMD22
TMD21
TMD20
0
0
0
0
R32
R32 port
1
TOD
Toggle output
0
TOD
0 output
1
TOD
1 output
0
—
Inhibited
TOD
PWM output
R32
Input capture (R32 port)
1
1
0
R32/TOD mode selection
1
0
1
1
1
Don’t care Don’t care Don’t care
Figure 45 Timer Mode Register D2 (TMD2)
• Timer write register D (TWDL: $011, TWDU: $012): Write-only register consisting of a lower digit
(TWDL) and an upper digit (TWDU) as shown in figures 46 and 47. The operation of timer write
register D is basically the same as that of timer write register C (TWCL: $00E, TWCU: $00F).
Timer write register D (lower digit) (TWDL: $011)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
TWDL3
TWDL2
TWDL1
TWDL0
Bit name
Figure 46 Timer Write Register D Lower Digit (TWDL)
60
HD404654 Series
Timer write register D (upper digit) (TWDU: $012)
Bit
Initial value
Read/Write
Bit name
3
2
1
0
Undefined Undefined Undefined Undefined
W
W
W
W
TWDU3
TWDU2
TWDU1
TWDU0
Figure 47 Timer Write Register D Upper Digit (TWDU)
• Timer read register D (TRDL: $011, TRDU: $012): Read-only register consisting of a lower digit
(TRDL) and an upper digit (TRDU) as shown in figures 48 and 49. The operation of timer read register
D is basically the same as that of timer read register C (TRCL: $00E, TRCU: $00F).
When the input capture timer operation is selected and if the count of timer D is read after a trigger is
input, either the lower or upper digit can be read first.
Timer read register D (lower digit) (TRDL: $011)
Bit
Initial value
Read/Write
Bit name
3
2
1
0
Undefined Undefined Undefined Undefined
R
R
R
R
TRDL3
TRDL2
TRDL1
TRDL0
Figure 48 Timer Read Register D Lower Digit (TRDL)
Timer read register D (upper digit) (TRDU: $012)
Bit
Initial value
Read/Write
Bit name
3
2
1
0
Undefined Undefined Undefined Undefined
R
R
R
R
TRDU3
TRDU2
TRDU1
TRDU0
Figure 49 Timer Read Register D Upper Digit (TRDU)
• Port mode register C (PMRC: $025): Write-only register that selects R40/EVND pin function as shown
in figure 50. It is reset to $0 by MCU reset.
61
HD404654 Series
Port mode register C (PMRC: $025)
Bit
3
2
1
0
Initial value
0
0
0
—
Read/Write
W
W
W
—
Bit name
PMRC3
PMRC2 PMRC1 Not used
PMRC1
R40/EVND mode selection
0
R40
1
EVND
PMRC2
D12/STOPC mode selection
0
D12
1
STOPC
PMRC3
D13/INT0 mode selection
0
D13
1
INT0
Figure 50 Port Mode Register C (PMRC)
• Detection edge select register 2 (ESR2: $027): Write-only register that selects the detection edge of
signals input to pin EVND as shown in figure 51. It is reset to $0 by MCU reset.
Detection edge register 2 (ESR2: $027)
Bit
3
2
1
0
Initial value
0
0
—
—
Read/Write
W
W
—
—
Bit name
ESR23
ESR22 Not used Not used
EVND detection edge
ESR23
ESR22
0
0
No detection
1
Falling-edge detection
0
Rising-edge detection
1
Double-edge detection *
1
Note: * Both falling and rising edges are detected.
Figure 51 Detection Edge Select Register 2 (ESR2)
62
HD404654 Series
Notes on Use
When using the timer output as PWM output, note the following point. From the update of the timer write
register until the occurrence of the overflow interrupt, the PWM output differs from the period and duty
settings, as shown in table 23. The PWM output should therefore not be used until after the overflow
interrupt following the update of the timer write register. After the overflow, the PWM output will have the
set period and duty cycle.
Table 23 PWM Output Following Update of Timer Write Register
PWM Output
Mode
Timer Write Register is Updated during
High PWM Output
Timer write
register
updated to
value N
Free running
Timer Write Register is Updated during
Low PWM Output
Timer write
register
updated to
value N
Interrupt
request
T × (255 – N) T × (N + 1)
Interrupt
request
T × (N' + 1)
T × (255 – N)
Reload
Timer write
register
updated to
value N
T
Interrupt
request
T × (255 – N)
T
Timer write
register
updated to
value N
T × (N + 1)
Interrupt
request
T
T × (255 – N)
T
63
HD404654 Series
Serial Interface 1
The MCU has one channel of serial interface. The serial interface serially transfers or receives 8-bit data,
and includes the following features.
• Multiple transmit clock sources
 External clock
 Internal prescaler output clock
 System clock
• Output level control in idle states
Serial interface 1
•
•
•
•
•
•
•
Serial data register 1 (SR1L: $006, SR1U: $007)
Serial mode register 1A (SM1A: $005)
Serial mode register 1B (SM1B: $028)
Port mode register A (PMRA: $004)
Miscellaneous register (MIS: $00C)
Octal counter (OC)
Selector
The block diagram of serial interface 1 is shown in figure 52.
64
HD404654 Series
Serial interrupt
request flag
(IFS1)
Octal counter
(OC)
Idle control
logic
SO1
Serial data
register
(SR1L/U)
I/O control
logic
SCK1
Transfer
control
1/2
1/2
System
clock
øPER
3
÷2048
÷8
÷32
÷128
÷512
÷2
Selector
Selector
SI1
Internal data bus
Clock
Serial mode register
1A (SM1A)
Prescaler S (PSS)
Serial mode register
1B (SM1B)
Figure 52 Block Diagram of Serial Interface 1
Serial Interface Operation
Selecting and Changing the Operating Mode: Table 24 lists the serial interfaces’ operating modes. To
select an operating mode, use one of these combinations of port mode register A (PMRA: $004), and serial
mode register 1A (SM1A: $005) settings; to change the operating mode of serial interface 1, always
initialize the serial interface internally by writing data to serial mode register 1A. Note that serial interface
1 is initialized by writing data to serial mode register 1A. Refer to the following section Registers for
Serial Interface for details.
65
HD404654 Series
Table 24 Serial Interface 1 Operating Modes
SM1A
PMRA
Bit 3
Bit 1
Bit 0
Operating Mode
1
0
0
Continuous clock output mode
1
Transmit mode
0
Receive mode
1
Transmit/receive mode
1
Pin Setting: The R41/SCK 1 pin is controlled by writing data to serial mode register 1A (SM1A: $005).
Pins R42/SI 1 and R4 3/SO 1 are controlled by writing data to port mode register A (PMRA: $004). Refer to
the following section Registers for Serial Interface for details.
Transmit Clock Source Setting: The transmit clock source of serial interface 1 is set by writing data to
serial mode register 1A (SM1A: $005) and serial mode register 1B (SM1B: $028). Refer to the following
section Registers for Serial Interface for details.
Data Setting: Transmit data of serial interface 1 is set by writing data to serial data register 1 (SR1L:
$006, SR1U: $007). Receive data of serial interface 1 is obtained by reading the contents of serial data
register 1. The serial data is shifted by the transmit clock and is input from or output to an external system.
The output level of the SO1 pin is invalid until the first data is output after MCU reset, or until the output
level control in idle states is performed.
Transfer Control: Serial interface 1 is activated by the STS instruction. The octal counter is reset to 000
by the STS instruction, and it increments at the rising edge of the transmit clock for serial interface. When
the eighth transmit clock signal is input or when serial transmission/reception is discontinued, the octal
counter is reset to 000, the serial 1 interrupt request flag (IFS1: $003, bit 2) is set, and the transfer stops.
When the prescaler output is selected as the transmit clock, the transmit clock frequency is selected as 4tcyc
to 8192tcyc by setting bits 0 to 2 (SM1A0–SM1A2) of serial mode register 1A (SM1A: $005) and bit 0
(SM1B0) of serial mode register 1B (SM1B: $028) as listed in table 25.
66
HD404654 Series
Table 25 Serial Transmit Clock (prescaler output)
SM1B
SM1A
Bit 0
Bit 2
Bit 1
Bit 0
Prescaler Division Ratio
Transmit Clock Frequency
0
0
0
0
÷ 2048
4096t cyc
1
÷ 512
1024t cyc
0
÷ 128
256t cyc
1
÷ 32
64t cyc
0
÷8
16t cyc
1
÷2
4t cyc
0
÷ 4096
8192t cyc
1
÷ 1024
2048t cyc
0
÷ 256
512t cyc
1
÷ 64
128t cyc
0
÷ 16
32t cyc
1
÷4
8tcyc
1
1
1
0
0
0
1
1
0
Operating States: Serial interface 1 has the following operating states; transitions between them are
shown in figure 53.




STS wait state
Transmit clock wait state
Transfer state
Continuous transmit clock output state (only in internal clock mode)
67
HD404654 Series
External clock mode
STS wait state
(Octal counter = 000,
Transmit clock disabled)
SM1A write
MCU reset
06 SM1A write (IFS1 ← 1)
04
01
STS instruction
02
Transmit clock wait state
(Octal counter = 000)
00
03
8 transmit clocks
Transmit clock
Transfer state
(Octal counter = 000)
05
STS instruction (IFS1 ← 1)
Internal clock mode
STS wait state
(Octal counter = 000,
transmit clock disabled)
SM1A write
18
Continuous transmit
clock output state
(PMRA 0, 1 = 0, 0)
Transmit clock
10
13
SM1A write
14
11
STS instruction
MCU reset
8 transmit clocks
16 SM1A write (IFS1 ← 1)
17
12 Transmit clock
Transmit clock wait state
(Octal counter = 000)
Transfer state
(Octal counter = 000)
15
STS instruction (IFS1 ← 1)
Note: Refer to the Operating States section for the corresponding encircled numbers.
Figure 53 Serial Interface State Transitions
• STS wait state: Serial interface 1 enters STS wait state by MCU reset (00, 10 in figure 53). In STS wait
state, serial interface 1 is initialized and the transmit clock is ignored. If the STS instruction is then
executed (01, 11), serial interface 1 enters transmit clock wait state.
• Transmit clock wait state: Transmit clock wait state is the period between STS execution and the
falling edge of the first transmit clock. In transmit clock wait state, input of the transmit clock (02, 12)
increments the octal counter, shifts serial data register 1 (SR1L: $006, SR1U: $007), and enters the
serial interface in transfer state. However, note that if continuous clock output mode is selected in
internal clock mode, the serial interface does not enter transfer state but enters continuous clock output
state (17).
The serial interface enters STS wait state by writing data to serial mode register 1A (SM1A: $005) (04,
14) in transmit clock wait state.
• Transfer state: Transfer state is the period between the falling edge of the first clock and the rising edge
of the eighth clock. In transfer state, the input of eight clocks or the execution of the STS instruction
sets the octal counter to 000, and the serial interface enters another state. When the STS instruction is
executed (05, 15), transmit clock wait state is entered. When eight clocks are input, transmit clock wait
68
HD404654 Series
state is entered (03) in external clock mode, and STS wait state is entered (13) in internal clock mode.
In internal clock mode, the transmit clock stops after outputting eight clocks.
In transfer state, writing data to serial mode register 1A (SM1A: $005) (06, 16) initializes serial
interface 1, and STS wait state is entered.
If the state changes from transfer to another state, the serial 1 interrupt request flag (IFS1: $003, bit 2) is
set by the octal counter that is reset to 000.
• Continuous clock output state (only in internal clock mode): Continuous clock output state is entered
only in internal clock mode. In this state, the serial interface does not transmit/ receive data but only
outputs the transmit clock from the SCK 1 pin.
When bits 0 and 1 (PMRA0, PMRA1) of port mode register A (PMRA: $004) are 00 in transmit clock
wait state and if the transmit clock is input (17), the serial interface enters continuous clock output state.
If serial mode register 1A (SM1A: $005) is written to in continuous clock output mode (18), STS wait
state is entered.
Output Level Control in Idle States: When serial interface 1 is in STS instruction wait state, the output
of serial output pin SO1 can be controlled by setting bit 1 (SM1B1) of serial mode register 1B (SM1B:
$028) to 0 or 1. The output level control example of serial interface 1 is shown in figure 54. Note that the
output level cannot be controlled in transfer state.
69
,
HD404654 Series
Transmit
clock
wait state
State
STS wait state
Transmit
clock
wait state
Transfer state
STS wait state
MCU reset
Port selection
PMRA write
External clock selection
SM1A write
Output level control in
idle states
Dummy write for
state transition
Output level control in
idle states
SM1B write
Data write for transmission
SR1L, SR1U
write
STS instruction
SCK1 pin (input)
SO1 pin
Undefined
LSB
MSB
IFS1
External clock mode
Flag reset at transfer completion
Transmit
clock
wait state
State
STS wait state
Transfer state
STS wait state
MCU reset
Port selection
PMRA write
Internal clock selection
SM1A write
Output level control in
idle states
SM1B write
Output level control in
idle states
Data write for transmission
SR1L, SR1U
write
STS instruction
SCK1 pin (output)
SO1 pin
Undefined
LSB
MSB
IFS1
Internal clock mode
Flag reset at transfer completion
Figure 54 Example of Serial Interface 1 Operation Sequence
70
HD404654 Series
Transmit Clock Error Detection (In External Clock Mode): Serial interface 1 will malfunction if a
spurious pulse caused by external noise conflicts with a normal transmit clock during transfer. A transmit
clock error of this type can be detected as shown in figure 55.
If more than eight transmit clocks are input in transfer state, at the eighth clock including a spurious pulse
by noise, the octal counter reaches 000, the serial 1 interrupt request flag (IFS1: $003, bit 2) is set, and
transmit clock wait state is entered. At the falling edge of the next normal clock signal, the transfer state is
entered. After the transfer is completed and IFS is reset, writing to serial mode register 1A (SM1A: $005)
changes the state from transfer to STS wait. At this time serial interface 1 is in the transfer state, and the
serial 1 interrupt request flag (IFS1: $003, bit 2) is set again, and therefore the error can be detected.
Notes on Use:
• Initialization after writing to registers: If port mode register A (PMRA: $004) is written to in transmit
clock wait state or in transfer state, serial interface 1 must be initialized by writing to serial mode
register 1A (SM1A: $005) again.
• Serial 1 interrupt request flag (IFS1: $003, bit 2) set: For serial interface 1, if the state is changed from
transfer state to another by writing to serial mode register 1A (SM1A: $005) or executing the STS
instruction during the first low pulse of the transmit clock, the serial 1 interrupt request flag (IFS1:
$003, bit 2) is not set. To set the serial 1 interrupt request flag (IFS1: $003, bit 2), a serial mode register
1A (SM1A: $005) write or STS instruction execution must be programmed to be executed after
confirming that the SCK 1 pin is at 1, that is, after executing the input instruction to port R4.
71
HD404654 Series
Transfer completion
(IFS1 ← 1)
Interrupts inhibited
IFS1 ← 0
SM1A write
Yes
IFS1 = 1
Transmit clock
error processing
No
Normal
termination
Transmit clock error detection flowchart
State
Transmit
clock
wait state
Transmit clock
wait state
Transfer state
SCK 1 pin
(input)
Transfer state
Noise
1
2
3
4
5
6
7
8
Transfer state has been
entered by the transmit clock
error. When SM1A is written,
IFS1 is set.
SM1A
write
IFS1
Flag set because octal
counter reaches 000.
Transmit clock error detection procedures
Figure 55 Transmit Clock Error Detection
72
Flag reset at
transfer completion.
HD404654 Series
Registers for Serial Interface 1
When serial interface 1 operation is selected, serial data is read and written by the following registers.
•
•
•
•
•
Serial mode register 1A (SM1A: $005)
Serial mode register 1B (SM1B: $028)
Serial data register 1 (SR1L: $006, SR1U: $007)
Port mode register A (PMRA: $004)
Miscellaneous register (MIS: $00C)
Serial Mode Register 1A (SM1A: $005): This register has the following functions (figure 56).
•
•
•
•
R4 1/SCK 1 pin function selection
Serial interface 1 transmit clock selection
Serial interface 1 prescaler division ratio selection
Serial interface 1 initialization
Serial mode register 1A is a 4-bit write-only register. It is reset to $0 by MCU reset.
A write signal input to serial mode register 1A (SM1A: $005) discontinues the input of the transmit clock
to serial data register 1 (SR1L: $006, SR1U: $007) and the octal counter, and the octal counter is reset to
000. Therefore, if a write is performed during data transfer, the serial 1 interrupt request flag (IFS1: $003,
bit 2) is set.
Written data is valid from the second instruction execution cycle after the write operation, so the STS
instruction must be executed at least two cycles after that.
73
HD404654 Series
Serial mode register 1A (SM1A: $005)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
SM1A3
SM1A2
SM1A1
SM1A0
Bit name
SM1A3
R41/SCK1
mode selection
0
R41
1
SCK1
Prescaler
division ratio
SM1A2
SM1A1
SM1A0
SCK1
Clock source
0
0
0
Output
Prescaler
Refer to
table 25
0
Output
System clock
—
1
Input
External clock
—
1
1
0
1
1
0
0
1
1
Figure 56 Serial Mode Register 1A (SM1A)
Serial Mode Register 1B (SM1B: $028): This register has the following functions (figure 57).
• Serial interface 1 prescaler division ratio selection
• Serial interface 1 output level control in idle states
Serial mode register 1B is a 2-bit write-only register. It cannot be written during data transfer.
By setting bit 0 (SM1B0) of this register, the serial interface 1 prescaler division ratio is selected. Only bit
0 (SM1B0) can be reset to 0 by MCU reset. By setting bit 1 (SM1B1), the output level of the SO1 pin is
controlled in idle states of serial interface 1. The output level changes at the same time that SM1B1 is
written to.
74
HD404654 Series
Serial mode register 1B (SM1B: $028)
Bit
3
2
1
0
Initial value
—
—
Undefined
0
Read/Write
—
—
W
W
Bit name
Not used Not used SM1B1
SM1B1
Output level control in idle states
SM1B0
SM1B0
Serial clock division ratio
0
Low level
0
Prescaler output divided by 2
1
High level
1
Prescaler output divided by 4
Figure 57 Serial Mode Register 1B (SM1B)
Serial Data Register 1 (SR1L: $006, SR1U: $007): This register has the following functions (figures 58
and 59)
• Serial interface 1 transmission data write and shift
• Serial interface 1 receive data shift and read
Writing data in this register is output from the SO1 pin, LSB first, synchronously with the falling edge of
the transmit clock; data is input, LSB first, through the SI1 pin at the rising edge of the transmit clock.
Input/output timing is shown in figure 60.
Data cannot be read or written during serial data transfer. If a read/write occurs during transfer, the
accuracy of the resultant data cannot be guaranteed.
Serial data register 1 (lower digit) (SR1L: $006)
Bit
3
Initial value
2
1
0
Undefined Undefined Undefined Undefined
Read/Write
R/W
R/W
R/W
R/W
Bit name
SR13
SR12
SR11
SR10
Figure 58 Serial Data Register 1 (SR1L)
Serial data register 1 (upper digit) (SR1U: $007)
Bit
3
Initial value
2
1
0
Undefined Undefined Undefined Undefined
Read/Write
R/W
R/W
R/W
R/W
Bit name
SR17
SR16
SR15
SR14
Figure 59 Serial Data Register 1 (SR1U)
75
HD404654 Series
Transmit clock
1
Serial output
data
2
3
4
5
6
7
LSB
8
MSB
Serial input data
latch timing
Figure 60 Serial Interface Output Timing
Port Mode Register A (PMRA: $004): This register has the following functions (figure 61).
• R4 2/SI 1 pin function selection
• R4 3/SO 1 pin function selection
Port mode register A is a 4-bit write-only register, and is reset to $0 by MCU reset.
Port mode register A (PMRA: $004)
Bit
3
2
1
0
Initial value
—
—
0
0
Read/Write
—
—
W
W
Bit name
Not used Not used PMRA1 PMRA0
PMRA0
R43/SO1 mode selection
0
R43
1
SO1
PMRA1
R42/SI1 mode selection
0
R42
1
SI1
Figure 61 Port Mode Register A (PMRA)
76
HD404654 Series
Miscellaneous Register (MIS: $00C): This register has the following functions (figure 62).
• R4 3/SO 1 pin PMOS control
Miscellaneous register is a 4-bit write-only register and is reset to $0 by MCU reset.
Miscellaneous register (MIS: $00C)
Bit
3
2
1
0
Initial value
0
0
—
—
Read/Write
W
W
—
—
MIS3
MIS2
Bit name
Not used Not used
MIS2
R43/SO1 PMOS on/off selection
0
On
1
Off
MIS3
Pull-up MOS on/off selection
0
Off
1
On
Figure 62 Miscellaneous Register (MIS)
77
HD404654 Series
DTMF Generator Circuit
The MCU provides a dual-tone multifrequency (DTMF) generator circuit. The DTMF signal consists of
two sine waves to access the switching system.
Figure 63 shows the DTMF keypad and frequencies. Each key enables tones to be generated corresponding
to each frequency. Figure 64 shows a block diagram of the DTMF circuit.
The OSC clock (400 kHz, 800 kHz, 2 MHz, 3.58 MHz or 4 MHz) is changed into four clock signals
through the division circuit (1/2, 1/5, 1/9 and 1/10). The DTMF circuit uses one of the four clock signals,
which is selected by system clock select register 1 (SSR1: $029) and system clock select register 2 (SSR2:
$02A) depending on the OSC clock frequency. The DTMF circuit has transformed programmable dividers,
sine wave counters, and control registers.
1
2
3
A
R1 (697 Hz)
4
5
6
B
R2 (770 Hz)
7
8
9
C
R3 (852 Hz)
*
0
#
D
R4 (941 Hz)
C1 (1,209 Hz)
C2 (1,336 Hz)
C3 (1,477 Hz)
C4 (1,633 Hz)
The DTMF generation circuit is controlled by the following three registers.
Figure 63 DTMF Keypad and Frequencies
78
HD404654 Series
Transformation program
divider
Sine wave
counter D/A
2
Feedback
VT ref
Tone generator
mode register
(TGM)
TONER output control
TONEC
Transformation program
divider
Sine wave
counter D/A
2
Feedback
Tone generator
control register
(TGC)
TONEC output control
2
f OSC
Internal data bus
TONER
400 kHz
800 kHz
2 MHz
1/2
1/5
400 kHz
Selector
System clock
selection register 1
(SSR1)
3.58 MHz
1/9
4 MHz
1/10
System clock
selection register 2
(SSR2)
1
Figure 64 Block Diagram of DTMF Generator Circuit
79
HD404654 Series
Tone Generator Mode Register (TGM: $019): Four-bit write-only register, which controls output
frequencies as shown in figure 65, and is reset to $0 by MCU reset.
Tone generator mode register (TGM: $019)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
Bit name
W
W
W
W
TGM3
TGM2
TGM1
TGM0
TGM3
TGM2
0
0
0
TONEC output frequencies
TGM1
TGM0
TONER output frequencies
f C1 (1,209 Hz)
0
0
f R1 (697 Hz)
1
f C2 (1,336 Hz)
0
1
f R2 (770 Hz)
1
0
f C3 (1,477 Hz)
1
0
f R3 (852 Hz)
1
1
f C4 (1,633 Hz)
1
1
f R4 (941 Hz)
Figure 65 Tone Generator Mode Register (TGM)
Tone Generator Control Register (TGC: $01A): Three-bit write-only register, which controls the
start/stop of the DTMF signal output as shown in figure 66, and is reset to $0 by MCU reset. TONER and
TONEC output can be independently controlled by bits 2 and 3 (TGC2, TGC3), and the DTMF circuit is
controlled by bit 1 (TGC1) of this register.
Tone generator control register (TGC: $01A)
Bit
3
2
1
0
Initial value
0
0
0
—
Read/Write
W
W
W
—
TGC3
TGC2
TGC1
Not used
TONEC output control (column)
TGC1
Bit name
TGC3
DTMF enable bit
0
No output
0
DTMF disable
1
TONEC output (active)
1
DTMF enable
TGC2
TONER output control (row)
0
No output
1
TONER output (active)
Figure 66 Tone Generator Control Register (TGC)
80
HD404654 Series
System Clock Select Registers 1 and 2 (SSR1: $029, SSR2: $02A): Four-bit write-only registers.
These registers must be set to the value specified in figures 67 and 68 depending on the frequency of the
oscillator connected to the OSC1 and OSC2 pins. Note that if the combination of the oscillation frequency
and the values in these registers is different from that specified in figures 67 and 68, the DTMF output
frequencies will differ from the correct frequencies as listed in Table 26.
System clock select register 1 (SSR1: $029)
Bit
3
2
Initial value
—
—
0
0
Read/Write
—
—
W
W
Bit name
0
1
Not used Not used SSR11
SSR10
System clock
SSR10 selection
SSR22
SSR11
0
0
0
400 kHz
0
0
1
800 kHz
0
1
0
2 MHz
0
1
1
4 MHz
1
×
×
3.58 MHz
× : Don’t care
Figure 67 System Clock Select Register 1 (SSR1)
Serial clock select register 2 (SSR2: $02A)
Bit
3
2
1
0
Initial value
—
0
—
—
Read/Write
—
W
—
—
Bit name
SSR22
Not used SSR22 Not used Not used
System clock selection
0
Selected from 400 kHz, 800 kHz,
2 MHz, 4 MHz *
1
3.58 MHz
Note: * Refer to system clock select register 1 (SSR1).
Figure 68 System Clock Select Register 2 (SSR2)
81
HD404654 Series
DTMF Output: The sine waves of the row-group and column-group are individually converted in the D/A
conversion circuit which provides a high-precision ladder resistance. The DTMF output pins (TONER,
TONEC) transmit the sine waves of the row-group and column-group, respectively. Figure 69 shows the
tone output equivalent circuit. Figure 70 shows the output waveform. One cycle of this wave consists of
32 slots. Therefore, the output waveform is stable with little distortion. Table 26 lists the frequency
deviation of the MCU from standard DTMF signals.
Table 26 Frequency Deviation of the MCU from Standard DTMF
fosc = 400 kHz, 800 kHz, 2 MHz, 4 MHz
fosc = 3.58 MHz
Standard
DTMF (Hz)
MCU (Hz)
Deviation from
Standard (%)
MCU (Hz)
Deviation from
Standard (%)
R1
697
694.44
–0.37
690.58
–0.92
R2
770
769.23
–0.10
764.96
–0.65
R3
852
851.06
–0.11
846.33
–0.67
R4
941
938.97
–0.22
933.75
–0.77
C1
1,209
1,212.12
0.26
1,205.39
–0.30
C2
1,336
1,333.33
–0.20
1,325.92
–0.75
C3
1,477
1,481.48
0.30
1,473.25
–0.25
C4
1,633
1,639.34
0.39
1,630.23
–0.17
Notes: This frequency deviation value does not include the frequency deviation due to the oscillator
element. Also note that in this case the ratio of the high level and low level widths in the oscillator
waveform due to the oscillator element will be 50%:50%.
Switch control
VTref
GND
TONER
TONEC
Figure 69 Tone Output Equivalent Circuit
82
HD404654 Series
VTref
1 2 3 4 5 6 7 8 9 10 1112 13 14 15 16 17 18 19 20 2122 23 24 25 26 27 28 29 30 31 32
GND
Time slot
Figure 70 Waveform of Tone Output
83
HD404654 Series
Comparator
The block diagram of the comparator is shown in figure 71. The comparator compares input voltage with
the reference voltage.
COMP0
COMP1
Selector
Setting 1 to bit 3 (CER3) of the compare enable register (CER: $018) executes a voltage comparison. If an
input voltage at COMP0 or COMP 1 is higher than the reference voltage, the TM or TMD command sets the
status flag (ST) high for the corresponding bits of the compare data register (CDR: $017) to COMP 0 or
COMP1. On the other hand, if an input voltage at COMP0 or COMP1 is lower than the reference voltage,
the TM or TMD command clears the ST to 0.
+
Comparator
Comparator data
register (CDR)
Internal data bus
–
VCref
2
Comparator enable
register (CER)
Figure 71 Block Diagram of Comparator
Compare Enable Register (CER: $018): Three-bit write-only register which enables comparator
operation, and selects the reference voltage and the analog input pin.
Compare Data Register (CDR: $017): Two-bit read-only register which latches the result of the
comparison between the analog input pins and the reference voltage. Bits 0 and 1 reflect the results of
comparison with COMP0 and COMP 1, respectively. This register can be read only by the TM or TMD
command. Only bit CER3 corresponds to the analog input pin, which is selected by bits CER0 and CER1.
After a compare operation, the data in this register is not retained.
Note on Use: During compare operation, pins RD0/COMP0 and RD1/COMP1 operate as analog inputs and
cannot operate as R ports.
The comparator can operate in active mode but is disabled in other modes.
RE0/VC ref cannot operate as an R port when the external input voltage is selected as the reference.
84
HD404654 Series
Compare enable register (CER: $018)
Bit
3
2
1
0
Initial value
0
—
0
0
Read/Write
W
—
W
W
Bit name
CER3
0
1
CER3
Not used CER1
Digital/Analog selection
CER0
CER1
CER0
0
0
COMP0
0
1
COMP1
1
0
Not used
1
1
Not used
Digital input mode:
RD0 /COMP0, RD1 /COMP1
operate as R port
Analog input mode:
RD0 /COMP0, RD1 /COMP1
operate as analog input
Analog input pin selection
Figure 72 Compare Enable Register
Compare data register (CDR: $017)
Bit
3
2
Initial value
—
—
Read/Write
—
—
Bit name
Not used Not used
1
0
Undefined Undefined
R
R
CDR1
CDR0
Result of COMP0 comparison
Result of COMP1 comparison
Figure 73 Compare Data Register
85
HD404654 Series
Programmable ROM (HD4074654)
The HD4074654 is a ZTAT microcomputer with built-in PROM that can be programmed in PROM
mode.
PROM Mode Pin Description
Pin No.
MCU Mode
PROM Mode
DP-42S
FP-44A
Pin Name
I/O
Pin Name
I/O
1
39
RD0/COMP0
I
CE
I
2
40
RD1/COMP1
I
OE
I
3
41
TONEC
O
4
42
TONER
O
5
43
VT ref
I
VCC
6
1
RE 0/VCref
I
M1
I
7
2
TEST
I
TEST
I
8
3
OSC 1
I
VCC
9
4
OSC 2
O
10
5
RESET
I
RESET
11
6
GND
I
GND
12
7
D0
I/O
O
13
8
D1
I/O
O
14
9
D2
I/O
VCC
15
10
D3
I/O
VCC
16
11
D4
I/O
O4
I/O
17
12
D5
I/O
O5
I/O
18
13
D6
I/O
O6
I/O
19
14
D7
I/O
O7
I/O
20
15
D8
I/O
A13
I
21
16
D9
I/O
A14
I
22
17
D12/STOPC
I
A9
I
23
18
D13/INT0
I
VPP
24
19
R0 0/INT1
I/O
M0
I
25
20
R1 0
I/O
A5
I
26
21
R1 1
I/O
A6
I
27
23
R1 2
I/O
A7
I
28
24
R1 3
I/O
A8
I
86
I
HD404654 Series
Pin No.
MCU Mode
PROM Mode
DP-42S
FP-44A
Pin Name
I/O
Pin Name
I/O
29
25
R2 0
I/O
A0
I
30
26
R2 1
I/O
A10
I
31
27
R2 2
I/O
A11
I
32
28
R2 3
I/O
A12
I
33
29
R3 0
I/O
A1
I
34
30
R3 1/TOC
I/O
A2
I
35
31
R3 2/TOD
I/O
A3
I
36
32
R3 3
I/O
A4
I
37
33
R4 0/EVND
I/O
O0
I/O
38
34
R4 1/SCK 1
I/O
O1
I/O
39
35
R4 2/SI1
I/O
O2
I/O
40
36
R4 3/SO 1
I/O
O3
I/O
41
37
SEL
I
42
38
VCC
I
–
22
NC
–
–
44
NC
–
VCC
Note: I/O: Input/output pin, I: Input pin, O: Output pin
87
HD404654 Series
Programming the Built-In PROM
The MCU’s built-in PROM is programmed in PROM mode. PROM mode is set by pulling TEST, M0, and
M1 low, and RESET low as shown in figure 74. In PROM mode, the MCU does not operate, but it can be
programmed in the same way as any other commercial 27256-type EPROM using a standard PROM
programmer and a 42-to-28-pin socket adapter. Recommended PROM programmers and socket adapters
of the HD4074654 are listed in table 28.
Since an HMCS400-series instruction is ten bits long, the HMCS400-series MCU has a built-in conversion
circuit to enable the use of a general- purpose PROM programmer. This circuit splits each instruction into
five lower bits and five upper bits that are read from or written to consecutive addresses. This means that
if, for example, 4 kwords of built-in PROM are to be programmed by a general-purpose PROM
programmer, an 8 kbyte address space ($0000–$7FFF) must be specified.
Warnings
1. Always specify addresses $0000 to $1FFF when programming with a PROM programmer. If address
$2000 or higher is accessed, the PROM may not be programmed or verified correctly. Set all data in
unused addresses to $FF.
Note that the plastic-package version cannot be erased or reprogrammed.
2. Make sure that the PROM programmer, socket adapter, and LSI are aligned correctly (their pin 1
positions match), otherwise overcurrents may damage the LSI. Before starting programming, make
sure that the LSI is firmly fixed in the socket adapter and the socket adapter is firmly fixed onto the
programmer.
3. PROM programmers have two voltages (VPP ): 12.5 V and 21 V. Remember that ZTAT devices
require a VPP of 12.5 V—the 21-V setting will damage them. 12.5 V is the Intel 27256 setting.
Programming and Verification
The built-in PROM of the MCU can be programmed at high speed without risk of voltage stress or damage
to data reliability.
Programming and verification modes are selected as listed in table 27.
For details of PROM programming, refer to the preface section, Notes on PROM Programming.
Table 27 PROM Mode Selection
Pin
Mode
CE
OE
VPP
O0–O7
Programming
Low
High
VPP
Data input
Verification
High
Low
VPP
Data output
Programming inhibited
High
High
VPP
High impedance
88
HD404654 Series
Table 28 Recommended PROM Programmers and Socket Adapters
PROM Programmer
Socket Adapter
Manufacturer
Model Name
Package
Manufacturer
Model Name
DATA I/O Corp.
121B
DP-42S
Hitachi
HS4654ESS01H
AVAL Corp.
PKW-1000
FP-44A
Hitachi
HS4654ESH01H
VCC
RESET
VCC
TEST
M0
VPP
M1
O0 to O7
Data
O0 to O7
A0 to A14
Address
A0 to A14
VPP
HD4074654
VCC
OSC1
D2
D3
VT ref
OE
OE
CE
CE
GND
Figure 74 PROM Mode Connections
89
HD404654 Series
Addressing Modes
RAM Addressing Modes
The MCU has three RAM addressing modes, as shown in figure 75 and described below.
Register Indirect Addressing Mode: The contents of the W, X, and Y registers (10 bits in total) are used
as a RAM address.
Direct Addressing Mode: A direct addressing instruction consists of two words. The first word contains
the opcode, and the contents of the second word (10 bits) are used as a RAM address.
Memory Register Addressing Mode: The memory registers (MR), which are located in 16 addresses
from $040 to $04F, are accessed with the LAMR and XMRA instructions.
W register
W1 W0
RAM address
X register
X3
X2
X1
Y register
X0
Y3
Y2
Y1
Y0
AP9 AP8 AP7 AP6 AP5 AP4 AP3 AP2 AP1 AP0
Register Direct Addressing
1st word of Instruction
Opcode
2nd word of Instruction
d
RAM address
9
d8
d7
d6
d5
d4
d3
d2
d1
d0
AP9 AP8 AP7 AP6 AP5 AP4 AP3 AP2 AP1 AP0
Direct Addressing
Instruction
Opcode
0
RAM address
0
0
1
0
m1
m0
0
AP9 AP8 AP7 AP6 AP5 AP4 AP3 AP2 AP1 AP0
Memory Register Addressing
Figure 75 RAM Addressing Modes
90
m3 m2
HD404654 Series
ROM Addressing Modes and the P Instruction
The MCU has four ROM addressing modes, as shown in figure 76 and described below.
Direct Addressing Mode: A program can branch to any address in the ROM memory space by executing
the JMPL, BRL, or CALL instruction. Each of these instructions replaces the 14 program counter bits
(PC 13–PC0) with 14-bit immediate data.
Current Page Addressing Mode: The MCU has 64 pages of ROM with 256 words per page. A program
can branch to any address in the current page by executing the BR instruction. This instruction replaces the
eight low-order bits of the program counter (PC7–PC0) with eight-bit immediate data. If the BR instruction
is on a page boundary (address 256n + 255), executing that instruction transfers the PC contents to the next
physical page, as shown in figure 78. This means that the execution of the BR instruction on a page
boundary will make the program branch to the next page.
Note that the HMCS400-series cross macroassembler has an automatic paging feature for ROM pages.
Zero-Page Addressing Mode: A program can branch to the zero-page subroutine area located at $0000–
$003F by executing the CAL instruction. When the CAL instruction is executed, 6 bits of immediate data
are placed in the six low-order bits of the program counter (PC 5–PC0), and 0s are placed in the eight highorder bits (PC13–PC6).
Table Data Addressing Mode: A program can branch to an address determined by the contents of fourbit immediate data, the accumulator, and the B register by executing the TBR instruction.
P Instruction: ROM data addressed in table data addressing mode can be referenced with the P instruction
as shown in figure 77. If bit 8 of the ROM data is 1, eight bits of ROM data are written to the accumulator
and the B register. If bit 9 is 1, eight bits of ROM data are written to the R1 and R2 port output registers.
If both bits 8 and 9 are 1, ROM data is written to the accumulator and the B register, and also to the R1 and
R2 port output registers at the same time.
The P instruction has no effect on the program counter.
91
HD404654 Series
2nd word of instruction
1st word of instruction
[JMPL]
[BRL]
[CALL]
Opcode
p3
Program counter
p2
p1
p0
d9
d8
d7
d6
d5
d4
d3
d2
d1
d0
PC13 PC12 PC11 PC10 PC 9 PC 8 PC 7 PC 6 PC 5 PC 4 PC 3 PC 2 PC 1 PC 0
Direct Addressing
Instruction
[BR]
Program counter
Opcode
b7
b6
b5
b4
b3
b2
b1
b0
PC13 PC12 PC11 PC10 PC 9 PC 8 PC7 PC 6 PC 5 PC 4 PC 3 PC 2 PC 1 PC 0
Current Page Addressing
Instruction
[CAL]
0
Program counter
0
0
0
d5
Opcode
0
0
0
d4
d3
d2
d1
d0
0
PC13 PC12 PC11 PC10 PC 9 PC 8 PC 7 PC 6 PC 5 PC 4 PC 3 PC 2 PC 1 PC 0
Zero Page Addressing
Instruction
[TBR]
Opcode
p3
p2
p1
p0
Accumulator
B register
B3
0
Program counter
B0
A3
A2
A1
A0
0
PC13 PC12 PC11 PC10 PC 9 PC 8 PC 7 PC 6 PC 5 PC 4 PC 3 PC 2 PC 1 PC 0
Table Data Addressing
Figure 76 ROM Addressing Modes
92
B2 B1
HD404654 Series
Instruction
[P]
Opcode
p3
p2
p1
p0
B register
B3
0
B2 B1
Accumulator
B0
A3
A2
A1
A0
0
Referenced ROM address RA13 RA12 RA11 RA10 RA 9 RA 8 RA 7 RA 6 RA 5 RA 4 RA 3 RA 2 RA 1 RA 0
Address Designation
ROM data
RO9 RO8 RO7 RO6 RO5 RO4 RO3 RO2 RO1 RO0
Accumulator, B register
ROM data
B3
B2
B1
B0
A3 A
2
A1
A
0
If RO 8 = 1
RO9 RO8 RO7 RO6 RO5 RO4 RO3 RO2 RO1 RO0
Output registers R1, R2
R23 R22 R21 R20 R13 R12 R11 R10
If RO 9 = 1
Pattern Output
Figure 77 P Instruction
93
HD404654 Series
256 (n – 1) + 255
BR
AAA
256n
AAA
BBB
256n + 254
256n + 255
256 (n + 1)
NOP
BR
BR
BBB
AAA
NOP
Figure 78 Branching when the Branch Destination is on a Page Boundary
94
HD404654 Series
Absolute Maximum Ratings
Item
Symbol
Value
Unit
Supply voltage
VCC
–0.3 to +7.0
V
Programming voltage
VPP
–0.3 to +14.0
V
Pin voltage
VT
–0.3 to VCC + 0.3
V
Total permissible input current
∑Io
80
mA
2
Total permissible output current
–∑Io
50
mA
3
Maximum input current
Io
4
mA
4, 5
30
mA
4, 6
4
mA
7, 8
20
mA
7, 9
Maximum output current
–I o
Operating temperature
Topr
–20 to +75
°C
Storage temperature
Tstg
–55 to +125
°C
Notes
1
Notes: Permanent damage may occur if these absolute maximum ratings are exceeded. Normal operation
must be under the conditions stated in the electrical characteristics tables. If these conditions are
exceeded, the LSI may malfunction or its reliability may be affected.
1. Applies to D 13 (VPP) of the HD4074654.
2. The total permissible input current is the total of input currents simultaneously flowing in from all
the I/O pins to GND.
3. The total permissible output current is the total of output currents simultaneously flowing out from
VCC to all I/O pins.
4. The maximum input current is the maximum current flowing from each I/O pin to GND.
5. Applies to D 0–D 3, and R0–R4.
6. Applies to D 4–D 9 .
7. The maximum output current is the maximum current flowing out from V CC to each I/O pin.
8. Applies to D 4–D 9 and R0–R4.
9. Applies to D 0–D 3.
95
HD404654 Series
Electrical Characteristics
DC Characteristics (HD404652, HD404654: VCC = 1.8 to 6.0 V, GND = 0 V, Ta = –20 to +75°C;
HD4074654: V CC = 2.7 to 5.5 V, GND = 0 V, T a = –20 to +75°C, unless otherwise specified)
Item
Symbol
Pin(s)
Min
Typ
Max
Input high
voltage
VIH
RESET, STOPC,
INT0, INT1, SCK 1,
SI 1, EVND
0.9V CC
—
VCC + 0.3 V
OSC 1
VCC – 0.3 —
VCC + 0.3 V
RESET, STOPC,
INT0 INT1, SCK 1
SI 1, EVND
–0.3
—
0.10 VCC
V
OSC 1
–0.3
—
0.3
V
External clock
VCC – 1.0 —
—
V
–I OH = 0.5 mA
Input low
voltage
VIL
Unit Test Condition
Notes
External clock
Output high
voltage
VOH
SCK 1, SO1,
TOC,TOD
Output low
voltage
VOL
SCK 1, SO1, TOC, —
TOD
—
0.4
V
I OL = 0.4 mA
I/O leakage
current
| IIL |
RESET, STOPC, —
INT0, INT1, SCK 1,
SI 1, SO1, EVND,
OSC 1, TOC, TOD
—
1
µA
Vin = 0 V to VCC
VCC
—
5
—
mA VCC = 5 V,
f OSC = 4 MHz
Digital input mode
2, 5
I CC2
—
0.6
1.8
mA VCC = 3 V,
f OSC = 800 kHz
Digital input mode
2, 5
I CMP1
—
9
—
mA VCC = 5 V,
3, 5
f OSC = 4 MHz
Analog comp. mode
I CMP2
—
3.1
4.3
mA VCC = 3 V,
3, 5
f OSC = 800 kHz
Analog comp. mode
—
1.2
—
mA VCC = 5 V,
f OSC = 4 MHz
4, 5
—
0.2
0.7
mA VCC = 3 V
f OSC = 800 kHz
4, 5
—
1
5
µA
6
Current
I CC1
dissipation in
active mode
I SBY1
Current
dissipation in
standby
mode
VCC
I SBY2
Current
I STOP
dissipation in
stop mode
96
VCC
VCC = 3 V
1
HD404654 Series
Item
Symbol
Pin(s)
Min
Typ
Max
Unit Test Condition
Notes
Stop mode
retaining
voltage
VSTOP
VCC
—
1.3
—
V
7
Comparator
input
reference
voltage
scope
VC ref
VC ref
0
—
VCC – 1.2 V
Notes: 1. Output buffer current is excluded.
2. I CC1 and I CC2 are the source currents when no I/O current is flowing while the MCU is in reset
state.
Test conditions:
MCU:
Reset
Pins:
RESET at GND (0 to 0.3V)
TEST at V CC (VCC –0.3 to VCC)
3. RD0, RD1 pins are in analog input mode when no I/O current is flowing.
Test conditions:
MCU:
DTMF does not operate
Pins:
RD0/COMP0 at GND (0 V to 0.3 V)
RD1/COMP1 at GND (0 V to 0.3 V)
RE 0/VCref at GND (0 V to 0.3 V)
4. I SBY1 and I SBY2 are the source currents when no I/O current is flowing while the MCU timer is
operating.
Test conditions:
MCU:
I/O reset
Serial interface stopped
DTMF does not operate
Standby mode
Pins:
RESET at V CC (VCC –0.3 to VCC)
TEST at V CC (VCC –0.3 to VCC)
5. The current dissipation is in proportion to f OSC while the MCU is operating or is in standby mode.
The current dissipation when fOSC = F MHz is given by the following equation: Maximum value
(fOSC = F MHz) = F/4 X maximum value (fOSC = 4 MHz)
6. These are the source currents when no I/O current is flowing.
Test conditions:
Pins:
RESET at V CC (VCC –0.3 to VCC)
TEST at V CC (VCC –0.3 to VCC)
D13 at V CC (VCC –0.3 to VCC)*
Note: * Applies to HD4074654.
7. RAM data retention.
97
HD404654 Series
I/O Characteristics for Standard Pins (HD404652, HD404654: VCC = 1.8 to 6.0 V, GND = 0 V,
T a = –20 to +75°C; HD4074654: VCC = 2.7 to 5.5 V, GND = 0 V, Ta = –20 to +75°C, unless otherwise
specified)
Item
Symbol
Pin(s)
Min
Typ
Max
Unit
Test Condition
Notes
Input high
voltage
VIH
D12–D 13 ,
R0–RD, RE0
0.7V CC
—
VCC + 0.3 V
Input low
voltage
VIL
D12–D 13 ,
R0–RD, RE0
–0.3
—
0.3V CC
V
Output high
voltage
VOH
R0–R4
VCC –1.0 —
—
V
–I OH = 0.5 mA
Output low
voltage
VOL
R0–R4
—
—
0.4
V
I OL = 0.4 mA
I/O leakage
current
| IIL |
D12, R0–RD,
RE 0
—
—
1
µA
Vin = 0 V to VCC
1
D13
—
—
1
µA
Vin = 0 V to VCC
1, 2
—
—
1
µA
Vin = VCC – 0.3 V to VCC 1, 3
—
—
20
µA
Vin = 0 V to 0.3 V
—
30
—
µA
VCC = 3 V,
1, 3
Pull-up MOS –I PU
current
R0–R4
Input high
voltage
VIHA
COMP0,
COMP1
—
VC ref —
+0.05
V
Analog compare mode 4
Input low
VILA
COMP0,
COMP1
—
VC ref —
–0.05
V
Analog compare mode 4
Notes: 1.
2.
3.
4.
98
Vin = 0 V
Output buffer current is excluded.
Applies to HD404652, HD404654.
Applies to HD4074654.
Use an analog input reference voltage in the range 0 V ≤ VCref ≤ VCC – 1.2.
HD404654 Series
I/O Characteristics for High-Current Pins (HD404652, HD404654: VCC = 1.8 to 6.0 V, GND = 0 V, T a
= –20 to +75°C; HD4074654: VCC = 2.7 to 5.5 V, GND = 0 V, T a = –20 to +75°C, unless otherwise
specified)
Item
Symbol
Pin(s)
Min
Typ
Max
Input high
voltage
VIH
D0–D 9
0.7 VCC
—
VCC + 0.3 V
Input low
voltage
VIL
D0–D 9
–0.3
—
0.3 VCC
V
Output high
voltage
VOH
D0–D 9
VCC – 1.0 —
—
V
–I OH = 0.5 mA
D0–D 3
2.0
—
—
V
–I OH = 10 mA,
VCC = 4.5 V to 6.0 V
D0–D 9
—
—
0.4
V
I OL = 0.4 mA
D4–D 9
—
—
2.0
V
I OL = 15 mA,
VCC = 4.5 V to 6.0 V
2
D0–D 9
—
—
1
µA
Vin = 0 V to VCC
1
Pull-down
I PD
MOS current
D0–D 3
—
30
—
µA
VCC = 3 V, Vin = 3 V
Pull-up MOS –I PU
current
D4–D 9
—
30
—
µA
VCC = 3 V, Vin = 0 V
Output low
voltage
I/O leakage
current
VOL
| IIL |
Unit
Test Condition
Note
2
Notes: 1. Output buffer current is excluded.
2. When using HD4074654, V CC = 4.5 V to 5.5 V.
DTMF Characteristics (HD404652, HD404654: V CC = 1.8 to 6.0 V, GND = 0 V, Ta = –20 to +75°C;
HD4074654: VCC = 2.7 to 5.5 V, GND = 0 V, Ta = –20 to +75°C, unless otherwise specified)
Item
Symbol
Pin(s)
Min
Typ
Max
Unit
Test Condition
Note
Tone output
voltage (1)
VOR
TONER
500
660
—
mVrms
VT ref – GND = 2.0 V,
1
RL = 100 kΩ, VCC = 3.0 V
Tone output
voltage (2)
VOC
TONEC
520
690
—
mVrms
VT ref – GND = 2.0 V,
1
RL = 100 kΩ, VCC = 3.0 V
Tone output
distortion
%DIS
—
3
7
%
Short circuit between
TONER and TONEC
RL = 100 kΩ
2
Tone output
ratio
dBCR
—
2.5
—
dB
Short circuit between
TONER and TONEC
RL = 100 kΩ
2
Notes: 1. See figure 79.
2. See figure 80.
These characteristics are guaranteed for an operating frequency (fOSC) of 400 kHz, 800 kHz, 2 MHz,
3.58 MHz, or 4 MHz.
99
HD404654 Series
AC Characteristics (HD404652, HD404654: VCC = 1.8 to 6.0 V, GND = 0 V, Ta = –20 to +75°C;
HD4074654: VCC = 2.7 to 5.5 V, GND = 0 V, Ta = –20 to +75°C, unless otherwise specified)
Item
Symbol
Pin(s)
Min
Typ
Max
Unit
Clock
oscillation
frequency
f OSC
OSC 1, OSC 2
—
400
—
kHz
1
—
800
—
kHz
1
—
2
—
MHz
1
—
3.58
—
MHz
1
—
4
—
MHz
1
—
1
—
µs
f OSC = 4 MHz
1/4 division,
2
—
8
—
µs
f OSC = 4 MHz,
1/32 division
3
—
—
7.5
ms
VCC = 2.7 V to 6.0 V
4, 5,
13
—
—
60
ms
VCC = 1.8 V to 2.7 V
4, 5,
12
1100
—
—
ns
f OSC = 400 kHz
6
550
—
—
ns
f OSC = 800 kHz
6
215
—
—
ns
f OSC = 2 MHz
6
115
—
—
ns
f OSC = 3.58 MHz
6
105
—
—
ns
f OSC = 4 MHz
6
1100
—
—
ns
f OSC = 400 kHz
6
550
—
—
ns
f OSC = 800 kHz
6
215
—
—
ns
f OSC = 2 MHz
6
115
—
—
ns
f OSC = 3.58 MHz
6
105
—
—
ns
f OSC = 4 MHz
6
—
—
150
ns
f OSC = 400 kHz
6
—
—
75
ns
f OSC = 800 kHz
6
—
—
35
ns
f OSC = 2 MHz
6
—
—
25
ns
f OSC = 3.58 MHz
6
—
—
20
ns
f OSC = 4 MHz
6
Instruction
cycle time
Oscillation
stabilization
time
t cyc
t RC
OSC 1, OSC 2
(ceramic)
External
clock high
width
External
clock low
width
External
clock rise
time
100
t CPH
t CPL
t CPr
OSC 1
OSC 1
OSC 1
Test Condition
Notes
HD404654 Series
Item
Symbol
Pin(s)
Min
Typ
Max
Unit
Test Condition
Notes
External
clock fall
time
t CPf
OSC 1
—
—
150
ns
f OSC = 400 kHz
6
—
—
75
ns
f OSC = 800 kHz
6
—
—
35
ns
f OSC = 2 MHz
6
—
—
25
ns
f OSC = 3.58 MHz
6
—
—
20
ns
f OSC = 4 MHz
6
INT0, INT1,
EVND high
width
t IH
INT0, INT1,
EVND
2
—
—
t cyc
7
INT0, INT1,
EVND low
width
t IL
INT0, INT1,
EVND
2
—
—
t cyc
7
RESET low
width
t RSTL
RESET
2
—
—
t cyc
8
STOPC low
width
t STPL
STOPC
1
—
—
t RC
9
RESET rise
time
t RSTr
RESET
—
—
20
ms
8
STOPC rise
time
t STPr
STOPC
—
—
20
ms
9
Input
capacitance
Cin
All pins except —
D13, D4–D 7
—
15
pF
D4–D 7
—
—
30
pF
D13
—
—
15
pF
—
—
180
pF
—
—
2
t cyc
VCC = 2.7 V to 6.0 V
—
—
20
t cyc
VCC = 1.8 V to 2.7 V
Analog
comparator
stabilization
time
t CSTB
COMP0,
COMP1
f = 1 MHz, Vin = 0 V
10
11, 12
Notes: 1. Bits 0 and 1 (SSR10, SSR11) of system clock select register 1 (SSR1: $029) and bit 2 (SSR22)
of system clock select register 2 (SSR2: $02A) must be set according to the system clock
frequency.
2. SEL = 1
3. SEL = 0
4. The oscillation stabilization time is the period required for the oscillator to stabilize after V CC
reaches 2.7 V (1.8 V for HD404654 and HD404652) at power-on, after RESET input goes low
when stop mode is cancelled, or after STOPC input goes low when stop mode is cancelled. At
power-on or when stop mode is cancelled, RESET or STOPC must be input for at least tRC to
ensure the oscillation stabilization time. If using a ceramic oscillator, contact its manufacturer to
determine what stabilization time is required, since it will depend on the circuit constants and
stray capacitance.
101
HD404654 Series
5. Applies to ceramic oscillator only.
When using crystal oscillator: VCC = 2.7 V to 6.0 V, tRC = 40 ms (typ) or VCC = 1.8 V to 2.6 V, tRC =
60 ms (typ)
(OSC1, OSC 2)
Rf = 1 MΩ ± 20%
C1 = C2 = 10–22 pF ± 20%
Crystal: Equivalent to circuit
shown below
C0 = 7 pF max
RS = 100 Ω max
f = 400 kHz, 800 kHz,
2 MHz, 3.58 MHz, 4 MHz
C1
Crystal oscillator
OSC1
Crystal
oscillator
Rf
OSC2
C2
GND
L
CS RS
OSC1
OSC2
C0
•
•
Since the circuit constants change depending on the crystal or ceramic resonator and stray
capacitance of the board, the user should consult with the crystal or ceramic oscillator
manufacturer to determine the circuit parameters.
Wiring among OSC1, OSC 2, and elements should be as short as possible, and must not cross
other wiring (see figure 20).
6. Refer to figure 81.
7. Refer to figure 82.
8. Refer to figure 83.
9. Refer to figure 84.
10. Applies to HD4074654.
11. Analog comparator stabilization time is the period for the analog comparator to stabilize and for
correct data to be read after entering RD 0/COMP0 and RD1/COMP1 into analog input mode.
12. HD4074654 : V CC = 2.7 V to 5.5 V
102
HD404654 Series
Serial Interface Timing Characteristics (HD404652, HD404654: V CC = 1.8 to 6.0 V, GND = 0 V, T a =
–20 to +75°C; HD4074654: VCC = 2.7 to 5.5 V, GND = 0 V, Ta = –20 to +75°C, unless otherwise
specified)
During Transmit Clock Output
Item
Symbol
Pin (s) Min
Typ
Max
Unit
Test Condition
Note
Transmit clock cycle
time
t Scyc
SCK 1
1
—
—
t cyc
Load shown in figure 86
1
Transmit clock high
width
t SCKH
SCK 1
0.5
—
—
t Scyc
Load shown in figure 86
1
Transmit clock low
width
t SCKL
SCK 1
0.5
—
—
t Scyc
Load shown in figure 86
1
Transmit clock rise time t SCKr
SCK 1
—
100
—
ns
Load shown in figure 86
1
Transmit clock fall time
SCK 1
—
100
—
ns
Load shown in figure 86
1
Serial output data delay t DSO
time
SO1
—
—
500
ns
Load shown in figure 86
1
Serial input data setup
time
t SSI
SI 1
300
—
—
ns
1
Serial input data hold
time
t HSI
SI 1
300
—
—
ns
1
t SCKf
Note: 1. Refer to figure 85.
During Transmit Clock Input
Item
Symbol
Pin (s) Min
Typ
Max
Unit
Transmit clock cycle
time
t Scyc
SCK 1
1
—
—
t cyc
1
Transmit clock high
width
t SCKH
SCK 1
0.5
—
—
t Scyc
1
Transmit clock low
width
t SCKL
SCK 1
0.5
—
—
t Scyc
1
Transmit clock rise time t SCKr
SCK 1
—
100
—
ns
1
Transmit clock fall time
SCK 1
—
100
—
ns
1
Serial output data delay t DSO
time
SO1
—
—
500
ns
Serial input data setup
time
t SSI
SI 1
300
—
—
ns
1
Serial input data hold
time
t HSI
SI 1
300
—
—
ns
1
t SCKf
Test Condition
Load shown in figure 86
Note
1
Note: 1. Refer to figure 85.
103
HD404654 Series
RL = 100 kΩ
TONEC
RL = 100 kΩ
TONER
GND
Figure 79 TONE Output Load Circuit
TONEC
RL = 100 kΩ
TONER
GND
Figure 80 Distortion dBCR Load Circuit
OSC 1
1/fCP
VCC – 0.3 V
0.3 V
tCPL
tCPH
tCPr
tCPf
Figure 81 External Clock Timing
INT0, INT1, EVND
0.9 VCC
0.1 VCC
t IH
t IL
Figure 82 Interrupt Timing
104
HD404654 Series
RESET
0.9 VCC
tRSTL
0.1 V CC
tRSTr
Figure 83 Reset Timing
STOPC
0.9 VCC
tSTPL
0.1 V CC
tSTPr
Figure 84 STOPC Timing
t Scyc
t SCKf
SCK 1
VCC – 1.0 V (0.9 VCC )*
0.4 V (0.1 VCC )*
t SCKr
t SCKL
t SCKH
t DSO
SO 1
VCC – 1.0 V
0.4 V
t SSI
SI 1
t HSI
0.9 V CC
0.1 V CC
Note: * VCC – 1.0 V and 0.4 V are the threshold voltages for transmit clock output.
0.9 VCC and 0.1 VCC are the threshold voltages for transmit clock output.
Figure 85 Serial Interface Timing
105
HD404654 Series
VCC
RL = 2.6 kΩ
Test point
C
30 pF
R
12 kΩ
1S2074 H
or equivalent
Figure 86 Timing Load Circuit
106
HD404654 Series
Notes On ROM Out
Please pay attention to the following items regard ing ROM out.
On ROM out, fill the ROM area indicated below with 1s to create the same data size as 4-kword version
(HD404654). A 4-kword data size is required to change ROM data to mask manufacturing data since the
program used is for a 4-kword version.
This limitation applies when using an EPROM or a data base.
ROM 2-kword version:
HD404652
Address $0800 to $0FFF
$0000
Vector address
$000F
$0010
Zero-page subroutine
(64 words)
$003F
$0040
Pattern and program
(2048 words)
$07FF
$0800
Not used
$0FFF
Fill this area with all 1s
107
HD404654 Series
HD404652/HD404654 Option List
Please check off the appropriate applications and
enter the necessary information.
Date of order
Customer
Department
Name
ROM code name
1. ROM Size
LSI number
HD404652
2-kword
HD404654
4-kword
5. ROM Code Media
Please specify the first type below (the upper bits and lower bits are mixed together), when using the
EPROM on-package microcomputer type (including ZTAT™ version).
EPROM: The upper bits and lower bits are mixed together. The upper five bits and lower five bits are
programmed to the same EPROM in alternating order (i.e., LULULU...).
EPROM: The upper bits and lower bits are separated. The upper five bits and lower five bits are
programmed to different EPROMS.
6. Oscillator for OSC1 and OSC2
Ceramic oscillator
f=
MHz
Crystal oscillator
f=
MHz
External clock
f=
MHz
7. Stop Mode
Used
Not used
8. Package
DP-42S
FP-44A
108
HD404654 Series
Cautions
1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent,
copyright, trademark, or other intellectual property rights for information contained in this document.
Hitachi bears no responsibility for problems that may arise with third party’s rights, including
intellectual property rights, in connection with use of the information contained in this document.
2. Products and product specifications may be subject to change without notice. Confirm that you have
received the latest product standards or specifications before final design, purchase or use.
3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However,
contact Hitachi’s sales office before using the product in an application that demands especially high
quality and reliability or where its failure or malfunction may directly threaten human life or cause risk
of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation,
traffic, safety equipment or medical equipment for life support.
4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly
for maximum rating, operating supply voltage range, heat radiation characteristics, installation
conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used
beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable
failure rates or failure modes in semiconductor devices and employ systemic measures such as failsafes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other
consequential damage due to operation of the Hitachi product.
5. This product is not designed to be radiation resistant.
6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without
written approval from Hitachi.
7. Contact Hitachi’s sales office for any questions regarding this document or Hitachi semiconductor
products.
Copyright © Hitachi, Ltd., 1998. All rights reserved. Printed in Japan.
109