Si4825-DEMO Si4825 D EMO B OARD U SER ’ S G UIDE 1. Features ATAD (analog tune and analog display) AM/FM/SW radio Worldwide FM band support 64–109 MHz with 18 bands, see the Table 1 Worldwide AM band support 504–1750 kHz with 5 bands, see the Table 1 Worldwide SW band support 2.3–28.5 MHz with 18 wide bands or 18 narrow bands, see the Table 1 Twelve positions band switch for selecting different band according to the target market Two AAA battery operations with working voltage down to 2.0 V Economical potentiometer for frequency tuning replaces more expensive variable capacitor (PVC) Potentiometer and/or push button volume control FM 50 µs or 75 µs de-emphasis SW Wide/Narrow-band selection via a slide switch Table 1. Si4825 Band Sequence Definition Band Name Band Frequency Range De-emphasis (FM) Channel Space (AM) FM1 87–108 MHz 50 µs FM2 87–108 MHz 50 µs FM3 87–108 MHz 75 µs FM4 87–108 MHz 75 µs FM5 86.5–109 MHz 50 µs FM6 86.5–109 MHz 50 µs FM7 87.3–108.25 MHz 50 µs FM8 87.3–108.25 MHz 50 µs FM9 87.3–108.25 MHz 75 µs FM10 87.3–108.25 MHz 75 µs FM11 76–90 MHz 50 µs FM12 76–90 MHz 50 µs FM13 64–87 MHz 50 µs FM14 64–87 MHz 50 µs FM15 76–108 MHz 50 µs FM16 76–108 MHz 50 µs FM17 64–108 MHz 50 µs FM18 64–108 MHz 50 µs AM1 520–1710 kHz Rev. 0.1 3/13 10k Note Demo Board Default Demo Board Default Demo Board Default Copyright © 2013 by Silicon Laboratories Si4825-DEMO Si4825-DEMO Table 1. Si4825 Band Sequence Definition (Continued) Band Name 2 Band Frequency Range De-emphasis (FM) Channel Space (AM) Note AM2 522-1620 kHz 9k AM3 504-1665 kHz 9k AM4 522-1728 kHz / 520-1730 kHz AM5 510-1750 kHz SW1 SW Wide Band SW Narrow Band 2.3–10.0 MHz 2.30–2.49 MHz SW2 3.2–7.6 MHz 3.20–3.40 MHz Demo Board Default SW3 3.2–10.0 MHz 3.90–4.00 MHz Demo Board Default SW4 3.7–12.5 MHz 4.75–5.06 MHz SW5 3.9–7.5 MHz 5.6 –6.4 MHz SW6 5.6–22 MHz 5.95– 6.2 MHz SW7 5.8–12.1 MHz 6.8–7.6 MHz SW8 5.9–9.50 MHz 7.1–7.6 MHz SW9 5.9–18.0 MHz 9.2–10 MHz Demo Board Default SW10 7.0–16.0 MHz 11.45–12.25 MHz Demo Board Default SW11 7.0–23.0 MHz 11.6–12.2 MHz Demo Board Default SW12 9.0–16.0 MHz 13.4–14.2 MHz SW13 9.0–22.0 MHz 13.57–13.87 MHz Demo Board Default SW14 9.5–18.0 MHz 15 –15.9 MHz Demo Board Default SW15 10.0–16.0 MHz 17.1 –18 MHz SW16 10.0–22.0 MHz 17.48–17.9 MHz SW17 13.0–18.0 MHz 21.2–22 MHz SW18 18.0–28.5 MHz 21.45 –21.85 MHz Demo Board Default 9k / 10k 10k Demo Board Default Rev. 0.1 Si4825-DEMO 2. Overview This manual describes the operation of the Silicon Labs Si4825-DEMO board Rev1.1, November 20, 2012. The Silicon Laboratories Si4825-DEMO board is designed with the 16-pin SOIC packaged Si4825 chip, the revolutionary single chip AM/FM/SW receiver that integrates everything from antenna input to audio output and allows use of common and economical potentiometers to do the frequency tuning. It provides a complete portable analog tune analog display AM/FM/SW radio design. The Si4825-DEMO is designed with 1-layer PCB, allowing the lowest cost without sacrificing the RF performance. The demo board works with two AAA batteries and working voltage down to 2.0 V. 3. Description Figure 1 and Figure 2 shows the physical layout of the board with key components indicated. Figure 1. Si4825-DEMO Board Top Side Figure 2. Si4825-DEMO Board Bottom Side Rev. 0.1 3 Si4825-DEMO Power: BAT1: 2 cells AAA battery holder S1: Power on / off Audio Connectors: J5: Mono audio headphone output Antenna Selections: AM antenna: Ferrite stick antenna for AM J1: BNC connector for FM/ SW conductive testing or FM whip antenna J2: FM antenna selector 1 2 3 1-2: HP ANT (J5) 2-3: BNC (J1) J6: SMA connector for AM conductive testing J3: AM antenna selector 1 2 3 1-2: AM Ferrite Antenna 2-3: SMA (J6) Audio Output Test Point: For the general specification test, TP2 is the recommended audio signal test point. The audio test instrument should be connected to TP2 to get more accurate test results. J5 can also be used as an audio test point, but the test results may not be entirely accurate under some circumstances. 1 GND 2 AOUT 4 Rev. 0.1 Si4825-DEMO Tuner Output Test Point: For the tuner specification test, TP1 is the recommended tuner output test point. The audio test instrument should be connected to TP1 to get accurate test results. 1 AOUT 2 GND Main Components: U1: Silicon Laboratories Si4825 AM/FM/SW ATAD receiver U2: Audio amplifier Frequency scale: The analog display for tuning frequency Control Interface: VR1: Frequency tuning wheel. VR2: Volume control wheel S3,S4: The push buttons for volume control J4: Tuner VDD connector (connect tuner Pin14 VDD to VBAT or VCC) 1 2 3 1-2: VBAT 2-3: VCC J8: SW Wide/Narrow-band selector 1 2 3 1-2: SW Narrow-band 2-3: SW Wideband Rev. 0.1 5 Si4825-DEMO S2: Band switch for FM, AM and SW 1 2 3 4 5 6 7 8 9 10 11 12 1: FM3 (87–108 MHz) 2: FM17 (64–108 MHz) 3: AM1 (520–1710 kHz) 4: AM2 (522–1620 kHz) 5:SW2 (N 3.2–3.4 MHz) (W 3.2–7.6 MHz) 6:SW3 (N 3.9–4.0 MHz) (W 3.2–10.0 MHz) 7:SW9 (N 9.2–10.0 MHz) (W 5.9–18.0 MHz) 8: SW10 (N 11.45–12.25 MHz) (W 7.0–16.0 MHz) 9: SW11 (N 11.6–12.2 MHz) (W 7.0–23.0 MHz) 10: SW13 (N 13.57–13.87 MHz) (W 9.0–22.0 MHz) 11: SW14 (N 15.0–15.9 MHz) (W 9.5–18.0 MHz) 12: SW16 (N 17.48–17.9 MHz) (W 10.0–22.0 MHz) Note: N = SW Narrow-band, W = SW Wideband 6 Rev. 0.1 Si4825-DEMO 4. Operation S4825-DEMO board, a complete analog tune and analog display radio, is very easy to operate: 1. Switch the SW Wide/Narrow-band selector J8 to the desired SW Wideband or Narrow-band. 2. Switch the tuner VDD connector J4 to the desired VABT or VCC. 3. Put two AAA batteries into the battery compartment. 4. Switch the power switch to the ON position. The board will power up to a radio band according to the position of the band switch. 5. Change the band switch to the desired band. 6. Rotate the tuning wheel and find the desired frequency. 7. Rotate the volume control wheel or press the volume control push buttons to get a comfortable volume. Note: For FM listening, the earphone cable must be connected to the board when J2 is set to "HP ANT" or an external antenna must be connected to the BNC connector when J2 is set to "BNC". For AM listening, the ferrite antenna must be connected to the board and the J3 is set to "Ferrite" before Turning on the radio or band switching to AM. For FM/AM sensitivity and SNR test, the tuner output volume level must be set to maximum by pressing push button S4, or you might get degraded test results. Rev. 0.1 7 Si4825-DEMO 5. Bill of Materials ATAD AM/FM/SW receiver IC Si4825 with external 32.768 kHz crystal oscillator support LM4910 Audio amplifier IC See Table 2 for details Table 2. Si4825-DEMO Board Rev1.1 Bill of Materials 8 Item Qty Reference Description 1 5 C1 C16 C19 C24 C39 CAP,SM,0603,X7R 0.1 µ 2 2 C23 C27 CAP,SM,1210,X7R 220 µ 3 1 C13 CAP,SM,1210,X7R 47 µ 4 2 C14 C25 Electrolytic capacitor 5 2 C2-3 CAP,SM,0603,X7R 22p 6 2 C30-31 CAP,SM,0603,X7R 33n 7 1 C33 CAP,SM,0603,X7R 10p 8 1 C34 CAP,SM,0603,X7R 33p 9 3 C4 C12 C15 CAP,SM,0603,X7R 4.7 µ 10 2 C5 C36 CAP,SM,0603,X7R 0.47 µ 11 2 C8 C10 CAP,SM,0603,X7R 100p 12 1 C11 CAP,SM,0603,X7R 150p 13 1 C18 CAP,SM,0603,X7R 330p 14 1 R25 RES,SM,0603 0R 15 1 R22 RES,SM,0603 12k 16 1 R27 RES,SM,0603 100R 17 1 R31 RES,SM,0603 1k 18 1 R32 RES,SM,0603 10R 19 1 R17 RES,SM,0603 10k 20 1 R41 RES,SM,0603 120k 21 1 R3 RES,SM,0603 2.2k 22 2 R45 R5 RES,SM,0603 200R 23 3 R6 R23 R34 RES,SM,0603 100k 24 1 R20 RES,SM,0603 6.8k 25 2 R37 R38 RES,SM,0603 56k 26 1 R36 RES,SM,0603,Tolerance ±1% 33k 27 1 R29 RES,SM,0603,Tolerance ±1% 140k 28 1 R43 RES,SM,0603,Tolerance ±1% 40k 29 1 R44 RES,SM,0603,Tolerance ±1% 47k Rev. 0.1 VALUE 100 µ/4 V Si4825-DEMO Table 2. Si4825-DEMO Board Rev1.1 Bill of Materials (Continued) Item Qty Reference Description 30 5 R7 R9 R11 R12 R15 RES,SM,0603,Tolerance ±1% 10k 31 1 R8 RES,SM,0603,Tolerance ±1% 50k 32 4 R10 R28 R33 R35 RES,SM,0603,Tolerance ±1% 20k 33 1 R14 RES,SM,0603,Tolerance ±1% 60k 34 1 L1 RES,SM,0603 0R 35 3 B4 B5 B6 FERRITE BEAD,SM,0603 2.5k/100M 36 1 B1 FERRITE BEAD,SM,0603 NP 37 1 VR1 100k,±10%, Variable resistor(POT) 100k 38 1 VR2 10k,±20%, Variable resistor(POT) 10k 39 1 U1 SI4825, SOIC16 Si4825 40 1 U2 LM4910MA, SO8 LM4910MA 41 1 D1 LED 42 2 D2 D4 DIODE, SM, ESD, SOT23 43 1 Q1 TRANSISTOR NPN SOT23 44 1 Y1 CRYSTAL 45 1 J1 BNC VERTICAL BNC For FM/SW testing 46 1 J6 SMA VERTICAL SMA For AM testing 47 4 J2 J3 J4 J8 Single pole two throw switch 48 1 J5 Earphone jack 49 1 S1 Two pole two throw switch 50 1 S2 Single pole twelve throw switch 51 1 S3 S4 Push button 52 1 ANT1 AW ferrite stick antenna 53 1 BAT1 BATTERY BOX, AAA*2 SIZE 54 2 TP1 TP2 CONN,TH,1x2,HDR Rev. 0.1 VALUE LED BAV99 2SC9018 32.768 kHz 220 µH CONN,TH,1x2,HDR 9 Figure 3. Si4825-DEMO Board Rev 1.1 Schematic Si4825-DEMO 6. Schematics 10 Rev. 0.1 Si4825-DEMO Figure 4. Si4825-DEMO Board Gerber Rev 1.1 Rev. 0.1 11 Si4825-DEMO CONTACT INFORMATION Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 Tel: 1+(512) 416-8500 Fax: 1+(512) 416-9669 Toll Free: 1+(877) 444-3032 Email: [email protected] Internet: www.silabs.com Patent Notice Silicon Labs invests in research and development to help our customers differentiate in the market with innovative low-power, small size, analogintensive mixed-signal solutions. Silicon Labs' extensive patent portfolio is a testament to our unique approach and world-class engineering team. The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice. Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where personal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized application, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages. Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc. Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders. 12 Rev. 0.1