CP2120 SPI TO I 2C B RIDGE A N D GPIO P ORT E XPANDER Input and Output Port Pins Single Chip SPI to I2C Transfer 8 Pins Configurable as Push-Pull or Open-Drain Pin Configurable as an edge-triggered interrupt source All pins 5 V Tolerant Integrated clock; no external clock required On-Chip Voltage Monitor 1 Slave Serial Peripheral Interface (SPI) Up to 1.0 Mbit/s Transfers to Least Significant Bit or Most Significant Bit first byte transfers Configurable Supply Voltage of 2.7 V to 3.6 V Typical I2C Master Interface Operates at configurable rates up to 400 kHz 255 RX and TX Data Buffers operating current: 6.4 mA Package Pb-free 20-pin QFN Internal Oscillator Voltage Monitor MISO MOSI SCK CS INT active low interrupt pin SPI Interface Controller I2C Interface SDA SCL Internal Registers Port Controller Eight I/O Pins Edge-Triggered Interrupt Source Figure 1. Block Diagram Rev. 1.0 Copyright © 2015 by Silicon Laboratories CP2120 CP2120 2 Rev. 1.0 CP2120 TABLE OF CONTENTS Section Page 1. System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2. Global DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 3. Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 4. Pinout And Package Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 4.1. Pin Out Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 4.2. QFN-20 Pinout Diagram (Top View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 4.3. QFN-20 Pinout Diagram (Bottom View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 4.4. QFN-20 Solder Paste Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 5. SPI Slave Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 5.1. Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5.2. Internal Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5.3. SPI Byte Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5.4. SPI Timing Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5.5. I2C Activity During SPI Transactions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2C Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 6. I 6.1. Determining Pull-Up Register Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 6.2. I2C Internal Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 6.3. I2C Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6.4. I2C Receive Buffer Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6.5. I2C Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 7. Port I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 8. CP2120 Revision Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Rev. 1.0 3 CP2120 1. System Overview The CP2120 is a highly-integrated SPI-to-I2C Bridge Controller with an SPI interface that provides a simple and reliable method for communicating with I2C devices. The CP2120 includes a 4-wire serial peripheral interface (SPI), a serial I2C interface, 256 byte data buffers, an internal oscillator, eight input/output port pins, and one pin configurable as an edge-triggered interrupt source in a compact 4x4 package. No external components other than pull-up resisters on the I2C pins are required. The SPI Master controls the CP2120 across the SPI interface using a command set that governs all CP2120 configuration and operation. 2. Global DC Electrical Characteristics Table 1. Global Electrical Characteristics –40 to +85 °C, 25 MHz system clock unless otherwise specified. Parameter Test Condition Min Typ Max Unit VRST 3.0 3.6 V — 3.8 4.1 mA Specified Operating Temperature Range –40 — +85 °C VDD POR Threshold (VRST) 2.40 2.55 2.70 V Min Typ Max Unit Ambient temperature under bias –55 — 125 °C Storage Temperature –65 — 150 °C Voltage on any Port I/O Pin or RST with respect to GND –0.3 — 5.8 V Voltage on VDD with respect to GND –0.3 — 4.2 V Maximum Total current through VDD or GND — — 500 mA Maximum output current sunk by RST or any Port pin — — 100 mA Digital Supply Voltage Digital Supply Current VDD = 3.0 V 3. Absolute Maximum Ratings Table 2. Absolute Maximum Ratings Parameter Test Condition Note: Stresses above the absolute maximum ratings may cause permanent device damage. This is a stress rating only, and functional operation of the devices at any conditions equal to or greater than those indicated in the operational listings of this specification are not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. 4 Rev. 1.0 CP2120 4. Pinout And Package Definition 4.1. Pin Out Chart Name Pin # Type Description VDD 3 Power Supply Pin GND 2 Ground RST 4 Digital I/O Device Reset. Open-drain output of internal POR or VDD monitor. An external source can initiate a system reset by driving this pin low for at least 15 µs. SCLK 1 Digital In SPI Clock Input MISO 20 Digital Out SPI Slave Output MOSI 19 Digital In SPI Slave Input CS 18 Digital In SPI Slave Select SDA 17 Digital I/O I2C Data Input/Output SCL 16 Digital I/O I2C Clock Input/Output GPIO 0 5 Digital I/O General Purpose Configurable Digital Input/Output GPIO 1 12 Digital I/O General Purpose Configurable Digital Input/Output GPIO 2 11 Digital I/O General Purpose Configurable Digital Input/Output GPIO 3 10 Digital I/O General Purpose Configurable Digital Input/Output GPIO 4 9 Digital I/O General Purpose Configurable Digital Input/Output GPIO 5 8 Digital I/O General Purpose Configurable Digital Input/Output GPIO 6 7 Digital I/O General Purpose Configurable Digital Input/Output GPIO 7 6 Digital I/O General Purpose Configurable Digital Input/Output EINT 13 Digital I/O Edge-Triggered Interrupt Source INT 14 Digital Out CP2120 Interrupt Indicator NC 15 Digital Out Not connected, leave floating Rev. 1.0 5 CP2120 6 MISO MOSI CS SDA SCL 20 19 18 17 16 4.2. QFN-20 Pinout Diagram (Top View) S C LK 1 15 NC GND 2 14 IN T VDD 3 13 E IN T RST 4 12 G P IO 1 G P IO 0 5 11 G P IO 2 C P 2120 8 9 10 GPIO 4 GPIO 3 7 GPIO 6 GPIO 5 6 GPIO 7 GND Rev. 1.0 CP2120 4.3. QFN-20 Pinout Diagram (Bottom View) Table 4.1. QFN-20 Package Dimensions A A1 A2 A3 b D D2 E E2 e L N ND NE R AA BB CC DD Rev. 1.0 MIN 0.80 0 0 — 0.18 — 2.00 — 2.00 — 0.45 — — — 0.09 — — — — MM TYP 0.90 0.02 0.65 0.25 0.23 4.00 2.15 4.00 2.15 0.5 0.55 20 5 5 — 0.435 0.435 0.18 0.18 MAX 1.00 0.05 1.00 — 0.30 — 2.25 — 2.25 — 0.65 — — — — — — — — 7 CP2120 4.4. QFN-20 Solder Paste Recommendations 8 Rev. 1.0 CP2120 5. SPI Slave Bus The CP2120 provides a four-wire slave SPI interface. The CP2120's SPI Bus activates whenever the SPI Master pulls the NSS pin low. The master can then clock data into the CP2120 through the Master-Out-Slave-In (MOSI) pin and receive data from the CP2120 through the Master-In-Slave-Out (MISO) pin. The SPI Master provides the SPI with a clock source. Figure 2 shows typical connections for an SPI bus. SPI Master MISO MOSI SPICLK CS CP2120 SCLK CS Figure 2. SPI Bus Typical Connections SCLK should be held high when idle. Figure 3 shows a CP2120 data transfer on the SPI Bus. If the CP2120 is the only slave device on the SPI bus, the NSS pin can be tied low. SCK MOSI MSB Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 MISO MSB Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 NSS Figure 3. Slave Mode Data/Clock Timing Note: Some SPI clock speeds in the 100 kHz to 300 kHz range may result in communication issues. Moving the clock rate faster or slower will resolve this problem. Rev. 1.0 9 CP2120 5.1. Command Set An SPI Master controls the CP2120 by sending commands across the SPI bus. Some commands initiate I2C transactions, while other commands modify or monitor CP2120 operation and events. 5.2. Internal Registers The CP2120 maintains a set of internal registers that can be modified to configure general purpose port I/O and I2C operation and can be read to obtain device status. Commands reading to and writing from the internal registers can be issued at any time, even while an I2C transaction is in progress, as they do not initiate any I2C bus transactions. Table 3 shows a list of all internal registers. Table 3. Internal Register Addresses Internal Register Address Section IOCONFIG 0x00 7 IOSTATE 0x01 7 I2CCLOCK 0x02 6.1 I2CTO 0x03 6.1 I2CSTAT 0x04 6.2 I2CADR 0x05 6.1 RXBUFF 0x06 6.3 IOCONFIG2 0x07 7 EDGEINT 0x08 7 I2CTO2 0x09 6.1 5.2.1. Write to Internal Register SPI Master 0x20 COMMAND REGISTER X DATA BYTE A Write to Internal Register command updates the value of one of the CP2120's Internal Registers. A Write to Internal Register command begins with the command byte, 0x20, followed by the internal register address, followed by the new value of the internal register. Only one register can be accessed per Write to Internal Register command. 10 Rev. 1.0 CP2120 5.2.2. Read From Internal Register SPI Master REGISTER Address COMMAND 0x21 Don’t Care REGISTER DATA CP2120 A Read from Internal Register command retrieves the current value of one of the CP2120's internal registers. The command begins with the command byte, 0x21, followed by the internal register address. This byte is followed by the transmission of a "don't care" byte, which can be of any value and is ignored by the CP2120. After the "don't care" byte, the internal register value is transmitted across the MISO line. 5.3. SPI Byte Orientation The SPI Configuration command configures the bit orientation of transfers across the SPI bus to one of two states. If SPI transmits most-significant-bit first, bit 7 is transmitted first. If SPI transmits least-significant-bit first, bit 0 is transmitted first. 5.3.1. SPI Configuration SPI Master SPI CONFIGURATION COMMAND 0x18 The command begins with the command byte (0x18), followed by SPI Configuration byte, which should equal one of the values shown in the following table. Any values other than those listed in the table are ignored. Byte Value Configuration 0x81 Most Significant Bit First 0x42 Least Significant Bit First 5.4. SPI Timing Diagrams NSS TSE TCKL TSD SCK* TCKH TSIS TSIH MOSI TSEZ TSOH TSLH TSDZ MISO Figure 4. SPI Slave Timing Rev. 1.0 11 CP2120 Table 4. SPI Slave Timing Parameters Slave Mode Timing* (See Figure 4) TSE NSS Falling to First SCLK Edge 2 x TSYSCLK — ns TSD Last SCLK Edge to NSS Rising 2 x TSYSCLK — ns TSEZ NSS Falling to MISO Valid — 4 x TSYSCLK ns TSDZ NSS Rising to MISO High-Z — 4 x TSYSCLK ns TCKH SCLK High Time 5 x TSYSCLK — ns TCKL SCLK Low Time 5 x TSYSCLK — ns TSIS MOSI Valid to SCLK Sample Edge 2 x TSYSCLK — ns TSIH SCLK Sample Edge to MOSI Change 2 x TSYSCLK — ns TSOH SCLK Shift Edge to MISO Change — 4 x TSYSCLK ns TSLH Last SCLK Edge to MISO Change (CKPHA = 1 ONLY) 6 x TSYSCLK 8 x TSYSCLK ns *Note: TSYSCLK equals 24.5 MHz. 5.5. I2C Activity During SPI Transactions If the SPI Master attempts to transmit a command to the CP2120 while the I2C bus is inactive, the CP2120 will disable its slave response. If an I2C Master device on the bus attempts to address the CP2120 during this time, the CP2120 will not ACK the address defined in the I2CADR Internal Register. If the SPI Master attempts to transmit a command to the CP2120 while the CP2120 is acting as the Master on the I2C bus, the CP2120 will suspend I2C bus activity until the SPI Master has completed transmission of the command. For instance, if the SPI Master calls the Read Internal Register command while the CP2120 is in the middle of an I2C transaction, that I2C transaction will stall until the CP2120 completely processes the Read Internal Register command. 12 Rev. 1.0 CP2120 6. I2C Serial Interface The CP2120 provides an I2C interface able to transfer data at frequencies up to 400 kHz. During a transaction, the CP2120, operating as the I2C master, sources a data clock on the SCL pin as data travels across the bidirectional SDA pin to and from an I2C slave device. The I2C interface lines each require a pull-up resistor. Figure 5 shows a typical I2C bus. VDD RpU RpU SDA SCL I²C-bus I²C-BUS Device CP2120 I²C-BUS DEVICE Figure 5. Typical I2C Bus* Note: VDD is defined in Table 2, “Absolute Maximum Ratings,” on page 4. For Rpu values, please see “6.1. Determining PullUp Register Values” . Note: The I2C interface does not currently support repeated start transactions, as required by some I2C slave devices. 6.1. Determining Pull-Up Register Values Logic low to logic high transitions on the SCL and SDA pins, which are configured to open-drain output with external pull-ups to VDD, take the form of an exponential curve with an RC time constant, where C equals the capacitance of the bus and R equals the pull-up resistor value. I2C specification defines rise time as the time required for a signal level to change from Vmin +0.15 V to Vmax-0.15 V. By solving the exponential equation using a Vmin of 0 V and a Vmax of 3.3 V, the following equation can be used to find values for pull-up resistors: Rise time = 3.04448 RC Bus capacitance is governed by a number of factors, including signal trace length and capacitance introduced by devices on the bus. 8 mm PCB signal traces on a two-layer board generally add 1 pF of capacitance per centimeter of trace length. To determine the amount of capacitance introduced to the bus by I2C devices, consult those devices’ datasheets. The maximum capacitance allowed before the bus violates I2C specification is 400 pF. Rise time requirements vary depending on each connected I2C device’s timing requirements and the SCL clock frequency. The maximum rise time allowed by the I2C specification is 1000 ns. 6.2. I2C Internal Registers Features of the I2C interface are configured through the CP2120's Internal Registers. SCL clock frequency is set by writing to the I2CCLK Internal Register. The frequency can be determined using the equation below. The I2C frequency configured by the I2CCLOCK register is only an approximate frequency. Actual I2C frequencies can vary due to conditions on the bus, such as a slave device extending the SCL low time. 2000 2 I C Clock Frequency (kHz) = --------------------2 I CCLK Equation 1. I2C Clock Frequency Rev. 1.0 13 CP2120 Internal Register Definition 1. I2CCLOCK: I2C Clock Frequency Configuration R/W R/W R/W R/W R/W R/W R/W R/W I2CCK7 I2CCK6 I2CCK5 I2CCK4 I2CCK3 I2CCK2 I2CCK1 I2CCK0 Bit 7 Bit 6 Bit 5 Bit 4 Bit3 Bit 2 Bit 1 Bit 0 Internal Register Address: 0x02 Reset Value: 0xA0 Bit 7-0: I2CCK7-0: I2C Clock Frequency Configuration value (minimum register value = 5, maximum register value = 255) The transaction time-out counter, which terminates an I2C transaction after a set period of time has passed, can be configured through the I2CTO Internal Register. If the time-out counter is not enabled, the CP2120 will make only one attempt at executing an I2C transaction and abort if that transaction attempt fails. TO Time-out Frequency = ---------- ( Hz ) 128 Equation 2. CTO Time-Out Frequency Internal Register Definition 2. I2CTO: I2C Time Out R/W R/W R/W R/W R/W R/W R/W R/W TO6 TO5 TO4 TO3 TO2 TO1 TO0 TEN Bit 7 Bit 6 Bit 5 Bit 4 Bit3 Bit 2 Bit 1 Bit 0 Internal Register Address: 0x03 Reset Value: 0x00 Bit 7-1: TO6-0: Time Out Value Bit 0: TEN:Time Out Enable Bit. 0: Disable Timer. 1: Enable Timer. The SPI Master can assign an I2C address to the CP2120 by writing to the I2CADR Internal Register. Setting this address is not necessary for device operation. If set, the CP2120 will ACK this address when another I2C Master on the bus attempts to communicate with it. The CP2120 will NACK all attempts at data transfer when responding as an I2C slave. Internal Register Definition 3. I2CADR: I2C Address R/W R/W R/W R/W R/W R/W R/W R/W I2CAD7 I2CAD6 I2CAD5 I2CAD4 I2CAD3 I2CAD2 I2CAD1 I2CAD0 Bit 7 Bit 6 Bit 5 Bit 4 Bit3 Bit 2 Bit 1 Bit 0 Internal Register Address: 0x05 Reset Value: 0x00 Bit 7-Bit 0: I2CAD7-0: I2C Address Sets I2C bus address. 14 Rev. 1.0 CP2120 The SPI2I2C provides additional SMBus-related timers to enable I2C protocol compatibility. Setting the I2C Bus Free Detect enables the device to poll the SMBus lines and determine when a transfer can begin. Setting the SCL Low Time Out detect will cause an SMBus transaction to abort if the SCL line has been held low by a device for a period of approximately 25 ms. Internal Register Definition 4. I2CTO2: Additional I2C Time Outs R/W R/W R/W R/W R/W R/W R/W R/W Reserved Reserved Reserved Reserved Reserved Reserved FREN LWEN Bit 7 Bit 6 Bit 5 Bit 4 Bit3 Bit 2 Bit 1 Bit 0 Internal Register Address: Reset Value: Bit 1: Bit 0: 0x09 0x00 I2C Bus Free Detect 0: Bus Free Detect Disabled 1: Bus Free Detect Enabled I2C SCL Low Time Out Detect 0: SCL Low Time Out Detect disable 1: SCL Low Time Out Detect enable 6.3. I2C Status The CP2120 maintains an Internal Register, I2CSTAT, which describes the current status of the I2C Interface. The I2CSTAT register can be read at any time. The CP2120 updates I2CSTAT when an I2C transaction begins, when an I2C transaction completes (successfully or unsuccessfully), and when a received SPI command contains errors. It is not recommended that an SPI master poll the CP2120's I2CSTAT Internal Register to determine when an I2C transaction has completed. The SPI master should instead watch for the INT pin to drop low, and then read the I2CSTAT register to determine the I2C transaction results. Rev. 1.0 15 CP2120 Internal Register Definition 5. I2CSTAT: I2C Status Register R R R R R R R R I2ST7 I2ST6 I2ST5 I2ST4 I2ST3 I2ST2 I2ST1 I2ST0 Bit 7 Bit 6 Bit 5 Bit 4 Bit3 Bit 2 Bit 1 Bit 0 Internal Register Address: 0x04 Reset Value: 0x00 16 Bit 7–0 I2ST: I2C Status I2C Status Value Status Description 0xF0 I2C transaction completed successfully. 0xF1 Slave address NACKed. 0xF2 Slave data NACKed. 0xF3 I2C transaction in progress. 0xF8 I2C transaction timed out due to timer configured in I2CTO. 0xF9 Command’s Bytes to Transmit Byte and Data Buffer Size do not match, or Read Buffer read number of bytes greater than buffer count. 0xFA I2C SCL Low time-out, using timer configured in I2CTO2. 0xFB I2C bus free detect has been disabled, and the bus is not free. Rev. 1.0 CP2120 6.4. I2C Receive Buffer Size Bytes received from I2C transactions are stored in the 255-byte data buffer. The number of bytes currently stored inside this buffer is saved in the RXBUFF Internal Register. Internal Register Definition 6. RXBUFF: Receive Buffer Size Register R R R R R R R R RXB7 RXB6 RXB5 RXB4 RXB3 RXB2 RXB1 RXB0 Bit 7 Bit 6 Bit 5 Bit 4 Bit3 Bit 2 Bit 1 Bit 0 Internal Register Address: 0x06 Reset Value: 0x00 Bit 7-0: RXB7-0: Receive Buffer Size Indicates the number of bytes received during the last I2C read transaction. 6.5. I2C Commands SPI commands initiate all I2C transactions. The CP2120 executes I2C transactions only after every byte of the command has been successfully received across the SPI bus. Once the CP2120 has completed the I2C transaction prompted by the command, the INT pin will be pulled low to indicate that command execution has completed. If an I2C command is issued while an I2C command is in progress, the second I2C command will be ignored. 6.5.1. Write Bytes to I2C SPI Master COMMAND 0x00 NUMBER OF BYTES SLAVE ADDRESS +W DATA BYTE1 ... DATA BYTE N This command transmits data to an I2C slave device. The command begins with the command byte (0x00), followed by the number of bytes to be transmitted across I2C, which can range from 1 to 255, and the address of the I2C Slave. The SPI master then sends the data to be transmitted across I2C. Sending more or fewer bytes than was indicated by the second byte of the command will result in an error condition, and the I2C transaction will not be initiated. Once the I2C transaction completes, the CP2120 pulls the INT pin low and sets the internal register according to the results of the transaction. 6.5.2. Read Bytes from I2C SPI Master COMMAND 0x01 NUMBER OF BYTES SLAVE ADDRESS +R This command attempts to retrieve bytes from an I2C Slave device. The command begins with the command byte, 0x01, followed by the number of bytes to read (1 to 255) and the address of the I2C slave device. Once the I2C transaction completes, the CP2120 pulls the INT pin low and sets I2CSTAT according to the results of the transaction. The CP2120 saves the number of bytes stored in the buffer in the internal register named RXBUFF. A Read Buffer command can be issued to retrieve the bytes from the buffer. Note: If the SPI Master issues a second Read Bytes from I2C command before issuing a Read Buffer command, the bytes stored in the CP2120's buffer will be overwritten. Rev. 1.0 17 CP2120 6.5.3. Read Buffer SPI Master COMMAND 0x06 Don’t Care CP2120 ... Data Byte 0 Data Byte N The Read Buffer command retrieves bytes from the CP2120's data buffer. The command begins with the command byte, 0x06. After the command byte, the SPI Master must transmit a single byte of data, which is ignored by the CP2120. After receiving the ignored byte of data, the CP2120 transmits data bytes across the MISO pin. It is recommended that the SPI Master read the RXBUFF Internal Register to determine how many bytes are stored in the CP2120's buffer before issuing a Read Buffer command. If the SPI Master attempts to retrieve more bytes than the buffer contains, the CP2120 will signal the error in I2CSTAT. If an SPI Master attempts to retrieve fewer bytes than are stored in the data buffer, all bytes left in the buffer will be deleted when the Read Buffer command terminates. 6.5.4. Read After Write SPI Master 0x02 COMMAND NUMBER OF WRITE BYTES NUMBER OF READ BYTES SLAVE ADDRESS+W DATA WRITE BYTE 0 ... SLAVE ADDRESS+R DATA WRITE BYTE N The Read After Write command writes bytes to one I2C slave and then reads bytes from another I2C slave. The SPI Master calls this command by first sending the command byte, 0x02, then the number of bytes to write (1 to 255) and bytes to read (1 to 255). These bytes are followed by the address of the I2C slave to which the CP2120 will attempt to write bytes, followed by the data bytes to write. The last byte of the command is the I2C slave from which the CP2120 will attempt to read bytes. 6.5.5. Write After Write SPI Master 0x03 COMMAND NUMBER OF BYTES 1 NUMBER OF BYTES 2 SLAVE 1 ADDRESS +W DATA BYTE 1 ... DATA BYTE N SLAVE 2 ADDRESS +W DATA BYTE 1 ... DATA BYTE N The Write After Write command writes to an I2C slave device and then issues another write to a second I2C slave device. The command begins with the command byte, 0x08, followed by the number of bytes to write to the first I2C device and the bytes to write to the second I2C device. The SPI master sends the slave address of the first I2C device and the data bytes to write to the first I2C slave. The SPI Master then sends the slave address of the second I2C slave device followed by the data bytes to transmit to that slave device. 6.5.6. Write To Multiple Slaves SPI Master 0x 09 COMMAND Num Bytes Num Slaves Slave0 ... Slave N Data Byte0 ... Data Byte N The Write to Multiple Slaves command allows an SPI Master to write the same data buffer to multiple I2C slaves. The command begins with the command byte, 0x09, followed by the size of the data buffer (0 to 255), followed by the number of slaves (0 to 254). Next, the list of slave addresses is transmitted. Following that, the data buffer to write to each slave is transmitted. The combined size of the slave address list and the data buffer should not exceed 255 bytes. The I2CSTAT Internal Register shows the results from the last I2C transaction of the command. 18 Rev. 1.0 CP2120 7. Port I/O The CP2120 offers eight general-purpose port pins that can be configured as output, input, or quasi-bidirectional output by writing to the internal registers, IOCONFIG and IOCONFIG2. Pin state can be updated by writing to the internal register, IOSTATE. Reading the IOSTATE Internal Register will return the current values of each port pin. The port pin, EINT, can be configured as an edge-triggered interrupt source by writing to the EDGEINT Internal Register. The EIT bit sets the interrupt to trigger upon a 0 to 1 or a 1 to 0 logic change on the pin. The bit, EIE, enables the pin as an interrupt source. Once the interrupt has been configured and enabled, the CP2120 will pull the INT pin low when the port pin's logic value switches to “1'” or “0”, depending on the interrupt configuration specified in the EIT bit. When an interrupt is triggered, EIF in the EDGEINT Internal Register is set. Reading from EDGEINT will clear the EIF bit. Internal Register Definition 7. IOCONFIG: Port I/O Configuration R/W R/W R/W R/W R/W R/W R/W R/W PCIO3.1 PCIO3.0 PCIO2.1 PCIO2.0 PCIO1.1 PCIO1.0 PCIO0.1 PCIO0.0 Bit 7 Bit 6 Bit 5 Bit 4 Bit3 Bit 2 Bit 1 Bit 0 Internal Register Address: 0x00 Reset Value: 0x00 Bit 7-6: PCIO3.1-PCIO3.0: Port Configuration for GPIO Pin 3 Bit 5-4: PCIO2.1-PCIO2.0: Port Configuration for GPIO Pin 2 Bit 3-2: PCIO1.1-PCIO1.0: Port Configuration for GPIO Pin 1 Bit 1-0: PCIO0.1-PCIO0.0: Port Configuration for GPIO Pin 0 These bits select the port state for GPIO pins 3 through 0. PCIOx.1 PCIOx.0 GPIO Pin x Mode 0 0 Open Drain Output 0 1 Input Only 1 0 Push-Pull Output 1 1 Reserved Rev. 1.0 19 CP2120 Internal Register Definition 8. IOCONFIG2: Port I/O Configuration 2 R/W R/W R/W R/W R/W R/W R/W R/W PCIO7.1 PCIO7.0 PCIO6.1 PCIO6.0 PCIO5.1 PCIO5.0 PCIO4.1 PCIO4.0 Bit 7 Bit 6 Bit 5 Bit 4 Bit3 Bit 2 Bit 1 Bit 0 Internal Register Address: 0x07 Reset Value: 0x00 Bit 7-6: PCIO7.1-PCIO7.0: Port Configuration for GPIO Pin 7 Bit 5-4: PCIO6.1-PCIO6.0: Port Configuration for GPIO Pin 6 Bit 3-2: PCIO5.1-PCIO5.0: Port Configuration for GPIO Pin 5 Bit 1-0: PCIO4.1-PCIO4.0: Port Configuration for GPIO Pin 4 These bits select the port state for GPIO pins 7 through 4. PCIOx.1 PCIOx.0 GPIO Pin x Mode 0 0 Open Drain Output 0 1 Input Only 1 0 Push-Pull Output 1 1 Input Only Internal Register Definition 9. IOSTATE: Port I/O State R/W R/W R/W R/W R/W R/W R/W R/W GPIO7 GPIO6 GPIO5 GPIO4 GPIO3 GPIO2 GPIO1 GPIO0 Bit 7 Bit 6 Bit 5 Bit 4 Bit3 Bit 2 Bit 1 Bit 0 Internal Register Address: Reset Value: Bit 7-0: 20 0x01 0x00 GPIO7-0: General Purpose Input/Output State Write - Output appears on output pins. 0: GPIOx set to logic low output. 1: GPIO set to logic high output. Read - Reads port state. 0: GPIOx is logic low. 1: GPIOx is logic high. Rev. 1.0 CP2120 Internal Register Definition 10. EDGEINT: Edge Triggered Interrupt Enable R/W R/W R/W R/W R/W R/W R/W R/W EIF EIE EIT Rsvd Rsvd Rsvd Rsvd Rsvd Bit 7 Bit 6 Bit 5 Bit 4 Bit3 Bit 2 Bit 1 Bit 0 Internal Register Address: Reset Value: Bit 7: Bit 6: Bit 5: Bit 4–Bit 0: 0x08 0x00 EIF: Edge Triggered Interrupt Flag 0: No edge triggered event has occurred on the EI_INT pin. 1: Edge-triggered event has occurred on the EI_INT pin. EIE: Edge Triggered Interrupt Enable 0: Edge Triggered interrupts disabled. 1: Edge Triggered interrupts enabled. EIT: Edge Triggered Interrupt Trigger 0: Interrupt triggered on negative-to-positive digital transition on the EI_INT port pin. 1: Interrupt triggered on positive-to-negative digital transition on the EI_INT port pin. Not used. Rev. 1.0 21 CP2120 8. CP2120 Revision Number The CP2120 revision number can be retrieved by first sending the Revision Number command byte of 0x40 and then transmitting one “don’t care” transitional byte. The CP2120 then transmits the two-byte revision number, most significant byte first, in BCD format. For example, a transmitted byte sequence of “0x01 0x44” would indicate that the CP2120’s revision number is equal to 1.44. SPI Master 0x40 COMMAND Don’t Care Rev Num Byte 1 CP2120 22 Rev. 1.0 Rev Num Byte 2 CP2120 DOCUMENT CHANGE LIST Revision 0.1 to Revision 0.2 Various small text changes. Updated 4.1 Pin Out Chart. Updated 4.2 Pin Out Diagram. Updated Figure 2. SPI Bus Typical Connections. Added Table 3. Internal Register Addresses. Updated all CP2120 command drawings. Added section 6.1 Determining Pull-Up Register Values. Changed appearance of all Internal Register Definition charts. Changed contents of Section 8. CP2120 Revision Number. Revision 0.2 to Revision 0.3 Removed references to power down mode. Corrected Equation 1, “I2C Clock Frequency,” on page 13. In Internal Register 4, “I2CTO2: Additional I2C Time Outs,” on page 15, changed Internal Register Address to “0x09”. In Internal Register 5, “I2CSTAT: I2C Status Register,” on page 16, changed all bits to “R” instead of “R/W” In Internal Register 6, “RXBUFF: Receive Buffer Size Register,” on page 17, changed all bits to “R” instead of “R/W”. Revision 0.3 to Revision 0.4 Updated Figure 1. Updated Digital Supply Voltage in Table 2. Updated Figure 3. Revision 0.4 to Revision 1.0 Updated CS and INT to have the overbar in Section 4.1. Added VRST parameter to Table 1 on page 4. Updated the description of Register 7, “IOCONFIG: Port I/O Configuration,” on page 19 to describe 11b as Reserved. Added a note regarding no repeated start support in Section 6 on page 13. Added a note regarding SPI clock speeds to Section 5 on page 9. Rev. 1.0 23 CP2120 CONTACT INFORMATION Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 Please visit the Silicon Labs Technical Support web page: https://www.silabs.com/support/pages/contacttechnicalsupport.aspx and register to submit a technical support request. The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice. Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where personal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized application, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages. Silicon Laboratories, Silicon Labs, and USBXpress are trademarks of Silicon Laboratories Inc. Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders 24 Rev. 1.0