TAI-SAW TECHNOLOGY CO., LTD. 25.4x22 10MHz OCXO MODEL NO.: TP0019A REV. NO.: 1.0 Revise: Rev. Rev. Page Rev. Account Date 1 N/A Initial release 07/28/11’ N/A TAI-SAW TECHNOLOGY CO., LTD. Ref. No. Reviser Ginger Huang TST DCC Release document 2 TAI-SAW TECHNOLOGY CO., LTD. No. 3, Industrial 2nd Rd., Ping-Chen Industrial District, Taoyuan, 324, Taiwan, R.O.C. TEL: 886-3-4690038 FAX: 886-3-4697532 E-mail: [email protected] Web: www.taisaw.com 25.4x22 10MHz OCXO MODEL NO.: TP0019A REV. NO: 1.0 Characteristics Values Unit Note Nominal Frequency 10 MHz ±200ppb @25°C,Vc=1.5V Temperature Range Characteristics Operating G1 Storage Power - Consumption Characteristics Power Supply Max values at steady state Max values during Warm-up Frequency Control Characteristics Frequency tuning range Voltage Control Input impedance Linearity Reference Voltage Output Signal Characteristics Level Min. -40 -50 Nom. Max. 85 95 Unit °C °C Note Min. 4.75 Nom. 5 Max. 5.25 180 600 Unit V mA mA Note Max. 1.5 3 Unit ppm V KΩ % V Min. 0.7 0 100 Nom. 2.8 3 10 3.2 Nom. Max. HCMOS Min. VOH 2.7 VOL Rise/Fall time Duty cycle Load Frequency Stability Characteristics VS Temperature Range G1 VS Power Supply variation VS Load variation 0.3 10 60 40 15 Min. Nom. Max. 50 5 5 At 25°C <3 minutes at 25°C Note Slope Positive Unit Volt Volt ns % pF Note ||10K ohm Unit ±ppb ±ppb ±ppb Note Refer to freq at 25°C Vcc ±5% Load ±5% Aging Characteristics Medium/Long Term Stability Warm Up Values 1 day 1 month 1 Year 10 Y'rs 1 100 3 mn <100 ±ppb Note After continuous operating for 30days at ±ppb 25°C, daily fluctuation<3ppb Refer to 1H on @25°C Unit TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 3 Phase Noise Characteristics Static Conditions 1 Hz Short-term Stability Values 10 Hz 100Hz 1KHz -120 -135 -150 0.1s~10s 1.00E-11 Unit 10 KHz 100KHz -150 -150 dBc/Hz Note Phase jitter(RMS) <1.00 E -11 After 1 Hr power on Mechanical & Environmetal Conditions Characteristics Conditions Shocks IEC 68-2-27 Test Ea:30g/11 ms Sine Vibrations IEC 68-2-06 Test Fc:5g/10 to 500Hz Package - Pin Out Package Ref. Maximum package height Pin Out 942 drawing Unit: mm 14.0mm Pin 1: Pin 2: Pin 3: Pin 4 Pin 5: Pin 6: Pin 7: Vctrl Vref out Vcc RF out N.C. N.C. Ground Mechanical drawing Package Ref. 942 TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 4 BOTTOM VIEW SUGGESTED PAD No 2 copper area 1 4 5 6 7 17.8 [0.701] 3 3.5 [0.138] 2.5 [0.098] 23.5 [0.925] 4 [0.157] H Max 1,2 2.5 [0.098] 75 R0, Logo YYWW/XXXX Fo=XX.XMHz PN 7.62 [0.3] 22 [0.866] 17.8 [0.701] 25.4 [1] Recommended Reflow Profile: TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 5 tP TP Critial Zone TL to TP Ramp-u TL tL Temperature Ts Ts min Ramp-dow ts Preheat t 25°C to Peak Time Profile Feature Average ramp-up rate (TL to TP) Sn-Pb Assembly 3°C/second max. Pb-Free Assembly 3°C/second max. Preheat -Temperature Min Tsmin) -Temperature Min Tsmax) -Time (min to max) (ts) 120°c 180°c 30-120 seconds 140°c 210°c 30-120 seconds Tsmax to TL - Ramp-up Rate 3°C/second max. 3°C/second max. Time maintainted above - Temperature (TL) - Time (tL) 180°c 30-120 seconds 220°c 30-120 seconds Peak Temperature (TP) max 235°C min200°C max 245°C min230°C Time 25°C to Peak Temperature 360s max. 480s max. 20-40 seconds 20-40 seconds 6°C/second max. 6°C/second max. Time within 5°C of actual Peak Temperature (tp) Ramp-down Rate TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 6