Introduction bus ic dc/dc converter motor driver ic ripple counter driver ic I/O ic Sensor interface ic sensor ic ip’s E 909.01 HALIOS® optical switch ÿ E 910.41 Hall sensor- and contact monitor E 910.84 PIR light controller E 910.92 PIR motion detector E 910.98 Hall sensor interface 4 *, par. out E910.99 PIR light controller for DC/AC E 909.05 HALIOS® multi-purpose sensor ÿ Hall sensor- and contact monitor (8 channel, parallel interface) features description ÿ Supply voltage range VS 5.25 to 25V The IC is developed for automotive applications. It continuously ÿ Supply voltage range VDD 4.75 to 5.25V monitors up to 8 hall sensors or switches to GND. ÿ Maximum overvoltage protection up to 40V ÿ Low standby current (typical IS = 13µA) The input currents are compared to internal references. Currents ÿ Contact status monitoring by comparison of the exceeding – 11mA will force a logic ‘0’ at the output, while currents switch resistance with internal reference E910.41 pinning higher than -6mA will result in a logic ‘1’ at the output. ÿ Inputs are current limited ÿ High noise immunity If the IC is used to monitor switches, the switch resistance must ÿ Overtemperatur protected be higher than 5kÝ for ‘1’ and less than 330Ý for ‘0’ at the out- ÿ – 40°C to + 125 ºC operating temperature put. ÿ SO20w package The input current as well as the tristate driver are activated with application the enable pin. Due to the tristate outputs the IC can be used in ÿ Automotive electronics bus configuration. ÿ Monitor for Hall Sensors ÿ Monitor for mechanical switches Pin package Name Description 1 VS Supply voltage 2 IN0 Input for sensor or switch to GND 3 IN1 Input for sensor or switch to GND 4 IN2 Input for sensor or switch to GND 5 IN3 Input for sensor or switch to GND 6 IN4 Input for sensor or switch to GND 7 IN5 Input for sensor or switch to GND 8 IN6 Input for sensor or switch to GND 9 IN7 Input for sensor or switch to GND 10 EN 11 GND 12 OUT7 TTL compatible tristate data port 13 OUT6 TTL compatible tristate data port 14 OUT5 TTL compatible tristate data port 15 OUT4 TTL compatible tristate data port 16 OUT3 TTL compatible tristate data port 17 OUT2 TTL compatible tristate data port 18 OUT1 TTL compatible tristate data port 19 OUT0 TTL compatible tristate data port 20 VDD Logic supply voltage VS 1 20 IN0 2 19 IN1 3 18 IN2 4 17 IN3 5 16 IN4 6 15 IN5 7 14 IN6 8 13 IN7 9 12 EN 10 11 VDD OUT0 OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 GND SO20 Chip enable for input current and tristate outputs, active low Ground Block diagram VBAT VS VDD VDD CH7 CH0 Imax IN0 IN1 IN2 EN EN OUT0 Vref. OUT1 OUT2 IN3 OUT3 IN4 OUT4 IN5 OUT5 IN6 OUT6 IN7 OUT7 B E910.41 100 external µC Note ELMOS Semiconductor AG (below ELMOS) reserves the right to make changes to the product contained in this publication without notice. ELMOS assumes no responsibility for the use of any circuits described herein, conveys no licence under any patent or other right, and makes no representation that the circuits are free of patent infringement. While the information in this publication has been checked, no responsibility, however, is assumed for inaccuracies. ELMOS does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of a life-support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications. Copyright © 2007 ELMOS Reproduction, in part or whole, without the prior written consent of ELMOS, is prohibited. www.elmos.de | [email protected] elmos product catalog 2007/2008 101