Embedded USB Mass Storage Drive (e230) Features Embedded USB Mass Storage Drive (e230) MTEDCAR002SAJ-1M2/1M2IT, MTEDCAR004SAJ-1N2/1N2IT MTEDCAR008SAJ-1N2/1N2IT, MTEDCAR016SAJ-1N2/1N2IT MTEDCBR002SAJ-1M2/1M2IT, MTEDCBR004SAJ-1N2/1N2IT MTEDCBR008SAJ-1N2/1N2IT, MTEDCBR016SAJ-1N2/1N2IT MTEDCBE002SAJ-1M2/1M2IT, MTEDCBE004SAJ-1N2/1N2IT MTEDCBE008SAJ-1N2/1N2IT, MTEDCBE016SAJ-1N2/1N2IT MTEDCAE002SAJ-1M2/1M2IT, MTEDCAE004SAJ-1N2/1N2IT MTEDCAE008SAJ-1N2/1N2IT, MTEDCAE016SAJ-1N2/1N2IT Features • Capacity (unformatted)3: 2GB, 4GB, 8GB, or 16GB • Form factor – Standard (36.9mm x 26.6mm x 9.6mm) – Low profile (36.9mm x 26.6mm x 5.8mm) • Voltage: 5V ±5% and 3.3V ±5% • Operating temperature – Commercial (0°C to +70°C) – Industrial (–40°C to +85°C) • Micron® NAND Flash • Interface: Universal Serial Bus (USB) Specification, Revision 2.0 • USB support – USB Specification, Revisions 2.0, 1.1 – USB Mass Storage Class Specification, Revision 1.0 • Performance – Sequential READ1: 30 MB/s – Sequential WRITE 1: 22 MB/s (2GB and 4GB); 28 MB/s (8GB and16GB) • Reliability: >1 million device hours mean time between failure (MTBF) • Endurance: useful operating life of at least 5 years under the following conditions: – 8760 power-on hours per year – Active 100% of power-on hours – Typical operating conditions2: 2GB module: 16 GB/day; 4GB module: 32 GB/day; 8GB module: 64 GB/day; 16GB module: 128 GB/day • Static and dynamic wear-leveling • 15-bit error correction code (ECC) • Reliability reporting PDF: 09005aef84970b4f eusb_MTED_230_embedded.pdf - Rev. D 4/13 EN Notes: 1. Typical transfer rate measured with H2BENCH 3.6. 2. Assumes that 70% of total usable drive capacity contains static files. 3. 1GB = 1 billion bytes; formatted capacity is less. Warranty: Contact your Micron sales representative for further information regarding the product, including product warranties. 1 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. Products and specifications discussed herein are subject to change by Micron without notice. Embedded USB Mass Storage Drive (e230) Features Part Numbering Information Micron’s embedded USB drives are available in different configurations and densities. Visit www.micron.com for a list of valid part numbers. Table 1: Part Number Example Part Number Category Micron Tech- Product nology Family MT ED Drive Interface Drive Form Factor Drive Density NAND Flash Type Product Family Sector Size NAND Component Revision C AE 002 S AJ -1 M 1 Operating Temper- Producature tion Range Status IT ES Table 2: Part Number Information Scheme Part Number Category Category Details Micron Technology Micron Technology Product Family ED = Embedded drive Drive Interface C = USB 2.0 Drive Form Factor AE = Embedded USB: 5V standard profile (36.9mm x 26.6mm x 9.6mm) BE = Embedded USB: 5V low profile (36.9mm x 26.6mm x 5.8mm) AR = Embedded USB: 3V standard profile (36.9mm x 26.6mm x 9.6mm) BR = Embedded USB: 3V low profile (36.9mm x 26.6mm x 5.8mm) Drive Density 002 = 2GB 004 = 4GB 008 = 8GB 016 = 16GB NAND Flash Type S = SLC Product Family AJ = Option J Sector Size 1 = 512-byte NAND Component M = 8Gb; x8; 3.3V N = 16Gb; x8; 3.3V Revision 1 = First generation 2 = Second generation 3 = Third generation Operating Temperature Range Blank = Commercial (0°C to 70°C) Production Status Blank = Production IT = Industrial (40°C to 85°C) ES = Engineering sample MS = Mechanical sample PDF: 09005aef84970b4f eusb_MTED_230_embedded.pdf - Rev. D 4/13 EN 2 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. Embedded USB Mass Storage Drive (e230) General Description General Description Micron embedded universal serial bus (USB) mass storage drives provide 2GB, 4GB, 8GB, or 16GB of USB 2.0-compatible memory storage in a small form factor. The embedded USB drive is an ideal solution for applications that require low cost and high reliability. Typical applications include PC caching and boot drives for embedded computing, server, and networking systems. High performance, reliability, and easy implementation make Micron embedded USBs an ideal storage solution. To consistently deliver the best possible performance, the embedded USB uses only SLC NAND Flash, and all densities use two x8 NAND channels to the controller. In addition to being fast, SLC NAND Flash offers solid reliability, coupled with ECC and wear leveling. The USB system interface is widely available in many system designs and is easy to implement, enabling rapid time to market. The embedded USB consists of two TSOP-packaged Micron NAND Flash components, a USB controller, and a 10-pin USB connector on a PCB. Different densities are available depending on the number of die in each package and the density of each NAND Flash die. The drive operates at 5V ±5% or 3.3V ±5%. It uses industry-standard 10-pin connectors and supports USB Specification, Revision 2.0. It is also backward compatible with Revision 1.1 and can be used with operating systems that support USB Mass Storage Class Specification, Revision 1.0. Figure 1: Functional Block Diagram USB protocol USB connector NAND data bus Channel 1 USB controller Micron NAND Flash NAND command Channel 1 NAND data bus Channel 2 Micron NAND Flash Table 3: Nominal Package Dimensions, Density, and Weight Value Unit Height 9.6 (standard) 5.8 (low profile) mm Width 26.6 mm Length 36.9 mm Density 2, 4, 8, 16 GB 4.5 g Unit weight PDF: 09005aef84970b4f eusb_MTED_230_embedded.pdf - Rev. D 4/13 EN 3 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. Embedded USB Mass Storage Drive (e230) General Description Figure 2: Pin Assignments: 2 x 5 Connector 9 Key 7 GND 5 USB data (+) 3 USB data (–) 1 Vcc (+5V) 1 Vcc (+5V) 3 USB data (–) 5 USB data (+) 7 GND 9 Key NC NC NC NC NC NC NC NC NC NC 10 8 6 4 2 2 4 6 8 10 Top view (through PCB) Note: Bottom view 1. Diagram not to scale. Table 4: Signal/Pin Descriptions Symbol USB data (+), USB data (–) Type I/O Function Data inputs/outputs: The bidirectional I/Os transfer address, data, and instruction information. Data is output only during READ operations; at other times the I/Os are inputs. VCC Supply VCC power supply pin. VSS Supply VSS ground connection NC – No connect: NC pins are not internally connected. These pins can be driven or left floating. Key – This pin is keyed. PDF: 09005aef84970b4f eusb_MTED_230_embedded.pdf - Rev. D 4/13 EN 4 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. Embedded USB Mass Storage Drive (e230) Error Management Error Management The embedded USB incorporates advanced technology for defect and error management. It uses various combinations of hardware-based error correction algorithms and firmware-based wear-leveling algorithms. Over the life of the drive, uncorrectable errors may occur. An uncorrectable error is defined as data that is reported as successfully programmed to the drive, but when it is read out of the drive, the data differs from what was programmed. See the Uncorrectable Bit Error Rate Table. The mean time between failures (MTBF) can be predicted based on component reliability data obtained by following the methods referenced in the Telecordia SR-332 reliability prediction procedures for electronic equipment. Table 5: System Reliability Density MTFB (Operating Hours) 2–16GB >1 million device hours Table 6: Uncorrectable Bit Error Rate Uncorrectable Bit Error Rate (BER)1 Operation <1 bit error in 1015 bits READ Note: 1. BER is measured with a WRITE-to-READ ratio of 1:1. Wear-Leveling Algorithm The controller adds a built-in RAM register unit to record the erase count of each block. Accordingly, the controller can decide the frequency of wear leveling and choose the proper blocks to swap. This technique successfully averages the erase count of the data blocks. Also, an enhanced wear leveling algorithm now includes most static blocks in the recycling pool. Increasing the number of blocks makes the wear-leveling algorithm more robust, and in turn extends product life. PDF: 09005aef84970b4f eusb_MTED_230_embedded.pdf - Rev. D 4/13 EN 5 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. Embedded USB Mass Storage Drive (e230) Electrical Characteristics Electrical Characteristics Stresses greater than those listed may cause permanent damage to the drive. This is a stress rating only, and functional operation of the drive at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Table 7: Absolute Maximum Ratings Parameter/Condition Symbol Min Max Unit VCC –0.6 5.25 V VCC supply voltage Table 8: DC and Operating Characteristics Parameter/Condition Symbol Standby current Isb Active current ICC1 Min Typ Max Unit Condition – 60 70 mA VCC = 3V – 50 60 mA VCC = 5V – 100 120 mA VCC = 3V /5V Table 9: Recommended Operating Conditions Parameter/Condition Operating temperature Symbol Min Typ Max Unit TA 0 – 70 °C –40 – 85 °C 5V VCC 4.75 5.00 5.25 V 3.3V VCC 2.85 3.3 3.5 V VSS 0 0 0 V Commercial Industrial VCC supply voltage Ground supply voltage Table 10: Shock and Vibration Parameter/Condition Specification Shock 1500g/0.5ms Vibration PDF: 09005aef84970b4f eusb_MTED_230_embedded.pdf - Rev. D 4/13 EN 5–500Hz at 3.1G 6 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. Embedded USB Mass Storage Drive (e230) Compliance Compliance Micron embedded USB drives comply with the following requirements: • CE (Europe): EN55022, 2006 Class B and EN55024, 1998 + A1: 2001 + A2:2003 • FCC: CFR Title 47, Part 15, ICES-003, all Class B • UL (US): approval to UL-60950-1, 2nd Edition, 2007-03-27, IEC 60950-1:2005, 2nd Edition • RoHS, “green” package Configuration The following configuration options are available: • Micron's embedded USB drive can be configured as a boot drive. • The standard fix configuration should be mounted as local drive. Note: The embedded USB drive cannot be configured as a removable drive. PDF: 09005aef84970b4f eusb_MTED_230_embedded.pdf - Rev. D 4/13 EN 7 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. Embedded USB Mass Storage Drive (e230) Mechanical Information Mechanical Information The standard 10-pin (2 x 5) female electrical connector has a height of 7.4mm and a pitch of 2.54mm. It supports the standard USB 2.0 interface. The low profile 10-pin (2 x 5) female electrical connector has a height of 3.6mm and a pitch of 2.0mm. It supports the standard USB 2.0 interface. A mounting hole is also provided on the PCB for a stable, reliable connection to the mounting board. The motherboard pin headers listed in Table 9 are compatible with Micron’s embedded USB drives. Pin headers that are not listed may also be compatible. Table 11: Compatible Pin Headers Manufacturer Profile Part Number Type Pinrex Standard 212-92-05GB01 SMT 210-92-05GB01 Straight Amtek Standard PHIFS25-205GB Press fit PHIS25-205GB Straight TMM-105-01-S-D-02 Straight Samtec Low profile Reference Documents Reference documentation for the USB 2.0 standard (USB 2.0 specification, technical documents, compliance test procedures, and other related documents) can be found at www.usb.org/developers/docs. PDF: 09005aef84970b4f eusb_MTED_230_embedded.pdf - Rev. D 4/13 EN 8 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. Embedded USB Mass Storage Drive (e230) Package Dimensions Package Dimensions Figure 3: Embedded USB Package, Standard Profile 9.6 ±0.1 26.6 ±0.25 1.1 2.54 7.5 25 ±0.25 2.45 2.54 36.9 ±0.25 31.16 ±0.25 27.5 ±0.25 20.7 ±0.25 2.95 4.9 2.87 3X Ø2.03 Ø3.2 20.7 ±0.25 1.6 1 Note: PDF: 09005aef84970b4f eusb_MTED_230_embedded.pdf - Rev. D 4/13 EN 1. All dimensions are in millimeters. 9 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. Embedded USB Mass Storage Drive (e230) Package Dimensions Figure 4: Embedded USB Package, Low Profile 5.8 ±0.1 26.6 ±0.25 1.2 25 ±0.25 2.0 3.6 2.45 2.0 36.9 ±0.25 31.16 ±0.25 27.5 ±0.25 20.7 ±0.25 2.95 4.9 2.87 3X Ø2.03 Ø3.2 20.7 ±0.25 1.6 1 Note: PDF: 09005aef84970b4f eusb_MTED_230_embedded.pdf - Rev. D 4/13 EN 1. All dimensions are in millimeters. 10 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. Embedded USB Mass Storage Drive (e230) Revision History Revision History Rev. D – 4/13 • Updated the package drawing • Updated densities in order information Rev. C, Advance – 7/12 • Added 3V information to DC and Operating Conditions table Rev. B, Advance – 9/11 • Added low profile and 3V information Rev. A, Advance – 4/11 • Initial release 8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900 www.micron.com/productsupport Customer Comment Line: 800-932-4992 Micron and the Micron logo are trademarks of Micron Technology, Inc. All other trademarks are the property of their respective owners. This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein. Although considered final, these specifications are subject to change, as further product development and data characterization sometimes occur. PDF: 09005aef84970b4f eusb_MTED_230_embedded.pdf - Rev. D 4/13 EN 11 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved.