64Mb: x8, x16 SDRAM

64Mb: x8, x16 SDRAM
Features
SDR SDRAM
MT48LC8M8A2 – 2 Meg x 8 x 4 Banks
MT48LC4M16A2 – 1 Meg x 16 x 4 Banks
Features
Options
Marking
• Configuration
– 8 Meg x 8 (2 Meg x 8 x 4 banks)
– 4 Meg x 16 (1 Meg x 16 x 4 banks)
• Write recovery (tWR)
– tWR = 2 CLK1
• Plastic package – OCPL2
– 54-pin TSOP II (400 mil)
– 54-pin TSOP II (400 mil) Pb-free,
RoHS-compliant
– 54-ball VFBGA 8mm x 8mm
(x16 only)
– 54-ball VFBGA 8mm x 16mm, Pbfree, RoHS-compliant (x16 only)
• Timing – cycle time
– 6ns @ CL = 3 (x16 only)
– 7.5ns @ CL = 3 (PC133)
– 7.5ns @ CL = 2 (PC133)
• Self refresh
– Standard
– Low power
• Operating temperature range
– Industrial (–40˚C to +85˚C)
– Automotive (–40˚C to +105˚C)
• Revision
• PC100- and PC133-compliant
• Fully synchronous; all signals registered on positive
edge of system clock
• Internal, pipelined operation; column address can
be changed every clock cycle
• Internal banks for hiding row access/precharge
• Programmable burst lengths: 1, 2, 4, 8, or full page
• Auto precharge, includes concurrent auto precharge
and auto refresh modes
• Self refresh mode (not available on AAT devices)
• Refresh
– 64ms, 4096-cycle refresh (15.6µs/row)
(industrial)
– 16ms, 4096-cycle refresh (3.9µs/row)
(automotive)
• LVTTL-compatible inputs and outputs
• Single 3.3V ±0.3V power supply
• AEC-Q100
• PPAP submission
• 8D response time
Notes:
8M8
4M16
A2
TG
P
F4
B43
-6A
-75
-7E
None
L
AIT
AAT3
:J
1. See Micron technical note TN-48-05 on
Micron's Web site.
2. Off-center parting line.
3. Contact Micron for availability.
Table 1: Key Timing Parameters
CL = CAS (READ) latency
Access Time
Speed Grade
Clock
Frequency
CL = 2
CL = 3
Setup Time
-6A
167 MHz
–
5.5ns
1.5ns
1ns
-7E
143 MHz
–
5.4ns
1.5ns
0.8ns
-75
133 MHz
–
5.4ns
1.5ns
0.8ns
-7E
133 MHz
5.4ns
–
1.5ns
0.8ns
-75
100 MHz
6ns
–
1.5ns
0.8ns
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1
Hold Time
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
Products and specifications discussed herein are subject to change by Micron without notice.
64Mb: x8, x16 SDRAM
Features
Table 2: Address Table
Parameter
Configuration
8 Meg x 8
4 Meg x 16
2 Meg x 8 x 4 banks
1 Meg x 16 x 4 banks
Refresh count
4K
4K
Row addressing
4K A[11:0]
4K A[11:0]
Bank addressing
4 BA[1:0]
4 BA[1:0]
Column
addressing
512 A[8:0]
256 A[7:0]
Part Numbers
Architecture
Package
MT48LC8M8A2TG
8 Meg x 8
54-pin TSOP II
Table 3: 64Mb SDR Part Numbering
Note:
MT48LC8M8A2P
8 Meg x 8
54-pin TSOP II
MT48LC4M16A2TG
4 Meg x 16
54-pin TSOP II
MT48LC4M16A2P
4 Meg x 16
54-pin TSOP II
MT48LC4M16A2B41
4 Meg x 16
54-ball VFBGA
MT48LC4M16A2F41
4 Meg x 16
54-ball VFBGA
1. FBGA Device Decoder: www.micron.com/decoder.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
2
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Features
Contents
General Description ......................................................................................................................................... 7
Automotive Temperature .............................................................................................................................. 7
Functional Block Diagrams ............................................................................................................................... 8
Pin and Ball Assignments and Descriptions ..................................................................................................... 11
Package Dimensions ....................................................................................................................................... 14
Temperature and Thermal Impedance ............................................................................................................ 16
Electrical Specifications .................................................................................................................................. 19
Electrical Specifications – IDD Parameters ........................................................................................................ 21
Electrical Specifications – AC Operating Conditions ......................................................................................... 23
Functional Description ................................................................................................................................... 27
Commands .................................................................................................................................................... 28
COMMAND INHIBIT .................................................................................................................................. 28
NO OPERATION (NOP) ............................................................................................................................... 29
LOAD MODE REGISTER (LMR) ................................................................................................................... 29
ACTIVE ...................................................................................................................................................... 29
READ ......................................................................................................................................................... 30
WRITE ....................................................................................................................................................... 31
PRECHARGE .............................................................................................................................................. 32
BURST TERMINATE ................................................................................................................................... 32
Truth Tables ................................................................................................................................................... 33
Initialization .................................................................................................................................................. 38
Mode Register ................................................................................................................................................ 40
Burst Length .............................................................................................................................................. 42
Burst Type .................................................................................................................................................. 42
CAS Latency ............................................................................................................................................... 44
Operating Mode ......................................................................................................................................... 44
Write Burst Mode ....................................................................................................................................... 44
Bank/Row Activation ...................................................................................................................................... 45
READ Operation ............................................................................................................................................. 46
WRITE Operation ........................................................................................................................................... 55
Burst Read/Single Write .............................................................................................................................. 62
PRECHARGE Operation .................................................................................................................................. 63
Auto Precharge ........................................................................................................................................... 63
AUTO REFRESH Operation ............................................................................................................................. 75
SELF REFRESH Operation ............................................................................................................................... 77
Power-Down .................................................................................................................................................. 79
Clock Suspend ............................................................................................................................................... 80
Revision History ............................................................................................................................................. 83
Rev. C – 11/13 ............................................................................................................................................. 83
Rev. B – 3/12 ............................................................................................................................................... 83
Rev. A – 12/11 ............................................................................................................................................. 83
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
3
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Features
List of Figures
Figure 1: 8 Meg x 8 Functional Block Diagram ................................................................................................... 9
Figure 2: 4 Meg x 16 Functional Block Diagram ............................................................................................... 10
Figure 3: 54-Pin TSOP (Top View) .................................................................................................................. 11
Figure 4: 54-Ball VFBGA x16 (Top View) ......................................................................................................... 12
Figure 5: 54-Pin Plastic TSOP (400 mil) – Package Codes TG/P ......................................................................... 14
Figure 6: 54-Ball VFBGA (8mm x 8mm) – Package Codes F4/B4 ....................................................................... 15
Figure 7: Example: Temperature Test Point Location, 54-Pin TSOP (Top View) ................................................. 17
Figure 8: Example: Temperature Test Point Location, 54-Ball VFBGA (Top View) .............................................. 18
Figure 9: ACTIVE Command .......................................................................................................................... 29
Figure 10: READ Command ........................................................................................................................... 30
Figure 11: WRITE Command ......................................................................................................................... 31
Figure 12: PRECHARGE Command ................................................................................................................ 32
Figure 13: Initialize and Load Mode Register .................................................................................................. 39
Figure 14: Mode Register Definition ............................................................................................................... 41
Figure 15: CAS Latency .................................................................................................................................. 44
Figure 16: Example: Meeting tRCD (MIN) When 2 < tRCD (MIN)/tCK < 3 .......................................................... 45
Figure 17: Consecutive READ Bursts .............................................................................................................. 47
Figure 18: Random READ Accesses ................................................................................................................ 48
Figure 19: READ-to-WRITE ............................................................................................................................ 49
Figure 20: READ-to-WRITE With Extra Clock Cycle ......................................................................................... 50
Figure 21: READ-to-PRECHARGE .................................................................................................................. 50
Figure 22: Terminating a READ Burst ............................................................................................................. 51
Figure 23: Alternating Bank Read Accesses ..................................................................................................... 52
Figure 24: READ Continuous Page Burst ......................................................................................................... 53
Figure 25: READ – DQM Operation ................................................................................................................ 54
Figure 26: WRITE Burst ................................................................................................................................. 55
Figure 27: WRITE-to-WRITE .......................................................................................................................... 56
Figure 28: Random WRITE Cycles .................................................................................................................. 57
Figure 29: WRITE-to-READ ............................................................................................................................ 57
Figure 30: WRITE-to-PRECHARGE ................................................................................................................. 58
Figure 31: Terminating a WRITE Burst ............................................................................................................ 59
Figure 32: Alternating Bank Write Accesses ..................................................................................................... 60
Figure 33: WRITE – Continuous Page Burst ..................................................................................................... 61
Figure 34: WRITE – DQM Operation ............................................................................................................... 62
Figure 35: READ With Auto Precharge Interrupted by a READ ......................................................................... 64
Figure 36: READ With Auto Precharge Interrupted by a WRITE ........................................................................ 65
Figure 37: READ With Auto Precharge ............................................................................................................ 66
Figure 38: READ Without Auto Precharge ....................................................................................................... 67
Figure 39: Single READ With Auto Precharge .................................................................................................. 68
Figure 40: Single READ Without Auto Precharge ............................................................................................. 69
Figure 41: WRITE With Auto Precharge Interrupted by a READ ........................................................................ 70
Figure 42: WRITE With Auto Precharge Interrupted by a WRITE ...................................................................... 70
Figure 43: WRITE With Auto Precharge ........................................................................................................... 71
Figure 44: WRITE Without Auto Precharge ..................................................................................................... 72
Figure 45: Single WRITE With Auto Precharge ................................................................................................. 73
Figure 46: Single WRITE Without Auto Precharge ............................................................................................ 74
Figure 47: Auto Refresh Mode ........................................................................................................................ 76
Figure 48: Self Refresh Mode .......................................................................................................................... 78
Figure 49: Power-Down Mode ........................................................................................................................ 79
Figure 50: Clock Suspend During WRITE Burst ............................................................................................... 80
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
4
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Features
Figure 51: Clock Suspend During READ Burst ................................................................................................. 81
Figure 52: Clock Suspend Mode ..................................................................................................................... 82
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
5
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Features
List of Tables
Table 1: Key Timing Parameters ....................................................................................................................... 1
Table 2: Address Table ..................................................................................................................................... 2
Table 3: 64Mb SDR Part Numbering ................................................................................................................. 2
Table 4: Pin and Ball Descriptions .................................................................................................................. 13
Table 5: Temperature Limits .......................................................................................................................... 16
Table 6: Thermal Impedance Simulated Values ............................................................................................... 17
Table 7: Absolute Maximum Ratings .............................................................................................................. 19
Table 8: DC Electrical Characteristics and Operating Conditions ..................................................................... 19
Table 9: Capacitance ..................................................................................................................................... 20
Table 10: IDD Specifications and Conditions – Revision G ................................................................................ 21
Table 11: IDD Specifications and Conditions – Revision J ................................................................................. 22
Table 12: Electrical Characteristics and Recommended AC Operating Conditions ............................................ 23
Table 13: AC Functional Characteristics ......................................................................................................... 25
Table 14: Truth Table – Commands and DQM Operation ................................................................................. 28
Table 15: Truth Table – Current State Bank n, Command to Bank n .................................................................. 33
Table 16: Truth Table – Current State Bank n, Command to Bank m ................................................................. 35
Table 17: Truth Table – CKE ........................................................................................................................... 37
Table 18: Burst Definition Table ..................................................................................................................... 43
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
6
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
General Description
General Description
The 64Mb SDRAM is a high-speed CMOS, dynamic random-access memory containing
67,108,864 bits. It is internally configured as a quad-bank DRAM with a synchronous interface (all signals are registered on the positive edge of the clock signal, CLK). Each of
the x8’s 16,777,216-bit banks is organized as 4096 rows by 512 columns by 8 bits. Each of
the x16’s 16,777,216-bit banks is organized as 4096 rows by 256 columns by 16 bits.
Read and write accesses to the SDRAM are burst-oriented; accesses start at a selected
location and continue for a programmed number of locations in a programmed sequence. Accesses begin with the registration of an ACTIVE command, which is then followed by a READ or WRITE command. The address bits registered coincident with the
ACTIVE command are used to select the bank and row to be accessed (BA[1:0] select the
bank; A[11:0] select the row). The address bits registered coincident with the READ or
WRITE command are used to select the starting column location for the burst access.
The SDRAM provides for programmable read or write burst lengths (BL) of 1, 2, 4, or 8
locations, or the full page, with a burst terminate option. An auto precharge function
may be enabled to provide a self-timed row precharge that is initiated at the end of the
burst sequence.
The 64Mb SDRAM uses an internal pipelined architecture to achieve high-speed operation. This architecture is compatible with the 2n rule of prefetch architectures, but it also allows the column address to be changed on every clock cycle to achieve a highspeed, fully random access. Precharging one bank while accessing one of the other
three banks will hide the PRECHARGE cycles and provide seamless, high-speed, random-access operation.
The 64Mb SDRAM is designed to operate in 3.3V memory systems. An auto refresh
mode is provided, along with a power-saving, power-down mode. All inputs and outputs are LVTTL-compatible.
SDRAM devices offer substantial advances in DRAM operating performance, including
the ability to synchronously burst data at a high data rate with automatic column-address generation, the ability to interleave between internal banks to hide precharge
time, and the capability to randomly change column addresses on each clock cycle during a burst access.
Automotive Temperature
The automotive temperature (AAT) option adheres to the following specifications:
• 16ms refresh rate
• Self refresh not supported
• Ambient and case temperature cannot be less than –40°C or greater than +105°C
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
7
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Functional Block Diagrams
Functional Block Diagrams
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
8
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Functional Block Diagrams
Figure 1: 8 Meg x 8 Functional Block Diagram
Control logic
CKE
CLK
Command
decode
CS#
WE#
CAS#
RAS#
Bank 3
Bank 2
Bank 1
Mode register
12
Refresh 12
counter
Rowaddress
MUX
12
12
Bank 0
rowaddress
latch 4096
and
decoder
Bank 0
memory
array
(4096 x 512 x 8)
Sense amplifiers
4096
2
A[11:0],
BA0, BA1
14
Address
register
2
9
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
8
I/O gating
DQM mask logic
read data latch
write drivers
Bank
control
logic
Columnaddress
counter/
latch
1
512
(x8)
1
DQM
Data
output
register
8
8
DQ[7:0]
Data
input
register
Column
decoder
9
9
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Functional Block Diagrams
Figure 2: 4 Meg x 16 Functional Block Diagram
CS#
WE#
CAS#
RAS#
Control logic
Command
decode
CKE
CLK
Bank 3
Bank 2
Bank 1
Mode register
Refresh 12
counter
12
Rowaddress
MUX
12
12
Bank 0
rowBank 0
address
memory
latch 4096
array
and
(4096 x 256 x 16)
decoder
Sense amplifiers
4096
Address
14
register
2
16
I/O gating
DQM mask logic
read data latch
write drivers
2
A[11:0],
BA0, BA1
2
Bank
control
logic
256
(x16)
2
Data
output
register
16
16
DQML,
DQMH
DQ[15:0]
Data
input
register
Column
decoder
8
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
Columnaddress
counter/
latch
8
10
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Pin and Ball Assignments and Descriptions
Pin and Ball Assignments and Descriptions
Figure 3: 54-Pin TSOP (Top View)
x8
–
DQ0
–
NC
DQ1
–
NC
DQ2
–
NC
DQ3
–
NC
–
NC
–
–
–
–
–
–
–
–
–
–
–
–
Notes:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
x16
VDD
DQ0
VDDQ
DQ1
DQ2
VSSQ
DQ3
DQ4
VDDQ
DQ5
DQ6
VSSQ
DQ7
VDD
DQML
WE#
CAS#
RAS#
CS#
BA0
BA1
A10
A0
A1
A2
A3
VDD
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
x16
x8
VSS
DQ15
VSSQ
DQ14
DQ13
VDDQ
DQ12
DQ11
VSSQ
DQ10
DQ9
VDDQ
DQ8
VSS
NC
DQMH
CLK
CKE
NC
A11
A9
A8
A7
A6
A5
A4
VSS
–
DQ7
–
NC
DQ6
–
NC
DQ5
–
NC
DQ4
–
NC
–
–
DQM
–
–
–
–
–
–
–
–
–
–
–
1. A dash (–) indicates that the x8 pin function is the same as the x16 pin function.
2. Notches are not present on all packages.
11
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Pin and Ball Assignments and Descriptions
Figure 4: 54-Ball VFBGA x16 (Top View)
1
2
3
A
VSS
DQ15
B
DQ14
C
4
5
6
7
8
9
VSSQ
VDDQ
DQ0
VDD
DQ13
VDDQ
VSSQ
DQ2
DQ1
DQ12
DQ11
VSSQ
VDDQ
DQ4
DQ3
D
DQ10
DQ9
VDDQ
VSSQ
DQ6
DQ5
E
DQ8
NC
VSS
VDD
DQML
DQ7
F
DQMH
CLK
CKE
CAS#
RAS#
WE#
G
NC/A12
A11
A9
BA0
BA1
CS#
H
A8
A7
A6
A0
A1
A10
J
VSS
A5
A4
A3
A2
VDD
Top View
(Ball Down)
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1. The balls at A4, A5, and A6 are absent from the physical package. They are included to
illustrate that rows 4, 5, and 6 exist, but contain no solder balls.
12
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Pin and Ball Assignments and Descriptions
Table 4: Pin and Ball Descriptions
Symbol
Type
Description
CLK
Input
Clock: CLK is driven by the system clock. All SDRAM input signals are sampled on the positive
edge of CLK. CLK also increments the internal burst counter and controls the output registers.
CKE
Input
Clock enable: CKE activates (HIGH) and deactivates (LOW) the CLK signal. Deactivating the
clock provides precharge power-down and SELF REFRESH operation (all banks idle), active
power-down (row active in any bank), or CLOCK SUSPEND operation (burst/access in progress). CKE is synchronous except after the device enters power-down and self refresh modes,
where CKE becomes asynchronous until after exiting the same mode. The input buffers, including CLK, are disabled during power-down and self refresh modes, providing low standby
power. CKE may be tied HIGH.
CS#
Input
Chip select: CS# enables (registered LOW) and disables (registered HIGH) the command decoder. All commands are masked when CS# is registered HIGH, but READ/WRITE bursts already
in progress will continue, and DQM operation will retain its DQ mask capability while CS# is
HIGH. CS# provides for external bank selection on systems with multiple banks. CS# is considered part of the command code.
CAS#, RAS#,
WE#
Input
Command inputs: RAS#, CAS#, and WE# (along with CS#) define the command being entered.
x8:
DQM
Input
Input/output mask: DQM is sampled HIGH and is an input mask signal for write accesses and
an output enable signal for read accesses. Input data is masked during a WRITE cycle. The
output buffers are High-Z (two-clock latency) during a READ cycle. On the x8, DQML (pin 15)
is NC; DQMH is DQM. On the x16, DQML corresponds to DQ[7:0] and DQMH corresponds to
DQ[15:8]. DQML and DQMH are considered same-state when referenced as DQM.
BA[1:0]
Input
Bank address input(s): BA[1:0] define to which bank the ACTIVE, READ, WRITE, or PRECHARGE command is being applied.
A[11:0]
Input
Address inputs: A[11:0] are sampled during the ACTIVE command (row address A[11:0]) and
READ or WRITE command (column address A[8:0] for x8; A[7:0] for x16; with A10 defining auto precharge) to select one location out of the memory array in the respective bank. A10 is
sampled during a PRECHARGE command to determine whether all banks are to be precharged (A10 HIGH) or bank selected by BA[1:0] (A1 LOW). The address inputs also provide
the op-code during a LOAD MODE REGISTER command.
x16:
DQ[15:0]
I/O
Data input/output: Data bus for x16 (pins 4, 7, 10, 13, 42, 45, 48, and 51 are NC for x8).
x8:
DQ[7:0]
I/O
Data input/output: Data bus for x8.
VDDQ
Supply
DQ power: DQ power to the die for improved noise immunity.
VSSQ
Supply
DQ ground: DQ ground to the die for improved noise immunity.
VDD
Supply
Power supply: 3.3V ±0.3V.
VSS
Supply
Ground.
NC
–
x16:
DQML, DQMH
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
No connect: These should be left unconnected.
13
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Package Dimensions
Package Dimensions
Figure 5: 54-Pin Plastic TSOP (400 mil) – Package Codes TG/P
0.10
1.2 MAX
0.375 ±0.075 TYP
Pin #1 ID
0.80 TYP
(for reference only)
22.22 ±0.08
2X R 0.75
2X R 1.00
2X 0.71
Plated lead finish: 90% Sn, 10% Pb or 100% Sn
Plastic package material: Epoxy novolac
Package width and length do not include
mold protrusion. Allowable protrusion is
0.25 per side.
2X 0.10
2.80
Gage plane
10.16 ±0.08
0.25
+0.10
0.10
-0.05
11.76 ±0.20
See Detail A
0.15
+0.03
-0.02
0.50 ±0.10
0.80
Detail A
Notes:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1. All dimensions are in millimeters.
2. Package width and length do not include mold protrusion; allowable mold protrusion is
0.25mm per side.
3. Package may or may not be assembled with a location notch.
14
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Package Dimensions
Figure 6: 54-Ball VFBGA (8mm x 8mm) – Package Codes F4/B4
0.65 ±0.05
Seating plane
Solder ball material:
62% Sn, 36% Pb, 2% Ag or
96.5% Sn, 3% Ag, 0.5% Cu
Solder mask defined ball pads:
Ø0.40
Substrate material: Plastic laminate
Mold compound: Epoxy novolac
C
0.12 C
54X Ø0.45 ±0.05
Solder ball
diameter refers
to post reflow
condition. The prereflow diameter
is 0.42.
6.40
0.80
TYP
Ball A1 ID
Ball A1 ID
Ball A1
4.00 ±0.05
Ball A9
6.40
CL
8.00 ±0.10
3.20
0.80 TYP
CL
3.20
4.00 ±0.05
1.00 MAX
8.00 ±0.10
Notes:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1. All dimensions are in millimeters.
2. Recommended pad size = Ø 0.4mm SMD.
15
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Temperature and Thermal Impedance
Temperature and Thermal Impedance
It is imperative that the SDRAM device’s temperature specifications, shown in Temperature Limits below, be maintained to ensure the junction temperature is in the proper
operating range to meet data sheet specifications. An important step in maintaining the
proper junction temperature is using the device’s thermal impedances correctly. The
thermal impedances are listed in Table 6 (page 17) for the applicable die revision and
packages being made available. These thermal impedance values vary according to the
density, package, and particular design used for each device.
Incorrectly using thermal impedances can produce significant errors. Read Micron
technical note TN-00-08, “Thermal Applications” prior to using the thermal impedances listed in Table 6 (page 17). To ensure the compatibility of current and future designs, contact Micron Applications Engineering to confirm thermal impedance values.
The SDRAM device’s safe junction temperature range can be maintained when the T C
specification is not exceeded. In applications where the device’s ambient temperature
is too high, use of forced air and/or heat sinks may be required to satisfy the case temperature specifications.
Table 5: Temperature Limits
Parameter
Operating case temperature
Junction temperature
Symbol
Min
Max
Unit
Notes
TC
0
80
°C
1, 2, 3, 4
Industrial
–40
90
Automotive
–40
105
°C
3
°C
3, 5
Commercial
Commercial
Ambient temperature
0
85
Industrial
TJ
–40
95
Automotive
–40
110
0
70
Commercial
TA
Industrial
–40
85
Automotive
–40
105
–
260
Peak reflow temperature
Notes:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
TPEAK
°C
1. MAX operating case temperature, TC, is measured in the center of the package on the
top side of the device, as shown in Figure 7 (page 17), and Figure 8 (page 18).
2. Device functionality is not guaranteed if the device exceeds maximum TC during operation.
3. All temperature specifications must be satisfied.
4. The case temperature should be measured by gluing a thermocouple to the top-center
of the component. This should be done with a 1mm bead of conductive epoxy, as defined by the JEDEC EIA/JESD51 standards. Take care to ensure that the thermocouple
bead is touching the case.
5. Operating ambient temperature surrounding the package.
16
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Temperature and Thermal Impedance
Table 6: Thermal Impedance Simulated Values
Θ JA (°C/W)
Airflow =
0m/s
Θ JA (°C/W)
Airflow =
1m/s
Θ JA (°C/W)
Airflow =
2m/s
High Conductivity
70.5
61.2
57.2
54.6
13.7
Low Conductivity
80.6
67.7
61.5
46.1
4.9
High Conductivity
63.96
57.1
53.5
45.7
Low Conductivity
122.3
105.6
98.1
89.5
High Conductivity
101.9
93.5
88.8
87.6
Low Conductivity
96.9
81.9
81.9
69.5
High Conductivity
74.0
66.3
62.7
60.7
Die
Revision
Package
Substrate
G
54-pin TSOP
54-ball VFBGA
J
54-pin TSOP
54-ball VFBGA
Notes:
Θ JB (°C/W) Θ JC (°C/W)
20.7
11.5
1. For designs expected to last beyond the die revision listed, contact Micron Applications
Engineering to confirm thermal impedance values.
2. Thermal resistance data is sampled from multiple lots, and the values should be viewed
as typical.
3. These are estimates; actual results may vary.
Figure 7: Example: Temperature Test Point Location, 54-Pin TSOP (Top View)
22.22mm
11.11mm
Test point
10.16mm
5.08mm
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1. Package may or may not be assembled with a location notch.
17
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Temperature and Thermal Impedance
Figure 8: Example: Temperature Test Point Location, 54-Ball VFBGA (Top View)
8.00mm
4.00mm
Test point
8.00mm
4.00mm
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
18
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Electrical Specifications
Electrical Specifications
Stresses greater than those listed may cause permanent damage to the device. This is a
stress rating only, and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
reliability.
Table 7: Absolute Maximum Ratings
Voltage/Temperature
Symbol
Min
Max
Unit
Voltage on VDD/VDDQ supply relative to VSS
VDD/VDDQ
–1
4.6
V
Voltage on inputs, NC, or I/O balls relative to VSS
VIN
–1
4.6
Storage temperature (plastic)
TSTG
–55
150
°C
–
–
1
W
Notes
Power dissipation
Table 8: DC Electrical Characteristics and Operating Conditions
Notes 1–3 apply to all parameters and conditions; VDD/VDDQ = 3.3V ±0.3V
Parameter/Condition
Symbol
Min
Max
Unit
VDD, VDDQ
3
3.6
V
Input high voltage: Logic 1; All inputs
VIH
2
VDD + 0.3
V
4
Input low voltage: Logic 0; All inputs
VIL
–0.3
0.8
V
4
Output high voltage: IOUT = –4mA
VOH
2.4
–
V
Output low voltage: IOUT = 4mA
VOL
–
0.4
V
IL
–5
5
μA
Output leakage current: DQ are disabled; 0V ≤ VOUT ≤ VDDQ
IOZ
–5
–5
μA
Operating temperature:
Commercial
TA
0
70
˚C
Industrial
TA
–40
85
˚C
Automotive
TA
–40
105
˚C
Supply voltage
Input leakage current:
Any input 0V ≤ VIN ≤ VDD (All other balls not under test = 0V)
Notes:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1. All voltages referenced to VSS.
2. The minimum specifications are used only to indicate cycle time at which proper operation over the full temperature range is ensured; (0°C ≤ TA ≤ +70°C (commercial), –40°C ≤
TA ≤ +85°C (industrial), and –40°C ≤ TA ≤ +105°C (automotive)).
3. An initial pause of 100μs is required after power-up, followed by two AUTO REFRESH
commands, before proper device operation is ensured. (VDD and VDDQ must be powered
up simultaneously. VSS and VSSQ must be at same potential.) The two AUTO REFRESH
command wake-ups should be repeated any time the tREF refresh requirement is exceeded.
4. VIH overshoot: VIH,max = VDDQ + 2V for a pulse width ≤3ns, and the pulse width cannot
be greater than one-third of the cycle rate. VIL undershoot: VIL,min = –2V for a pulse
width ≤3ns.
19
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Electrical Specifications
Table 9: Capacitance
Note 1 applies to all parameters and conditions
Package
Parameter
TSOP package
VFBGA package
Notes:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
Symbol
Min
Max
Unit
Notes
Input capacitance: CLK
CL1
2.5
3.5
pF
2
Input capacitance: All other input-only
balls
CL2
2.5
3.8
pF
3
Input/output capacitance: DQ
CL0
4
6
pF
4
Input capacitance: CLK
CL1
1.5
3.5
pF
2
Input capacitance: All other input-only
balls
CL2
1.5
3.8
pF
3
Input/output capacitance: DQ
CL0
3
6
pF
4
1. This parameter is sampled. VDD, VDDQ = 3.3V; f = 1 MHz, TA = 25°C; pin under test biased
at 1.4V.
2. PC100 specifies a maximum of 4pF.
3. PC100 specifies a maximum of 5pF.
4. PC100 specifies a maximum of 6.5pF.
20
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Electrical Specifications – IDD Parameters
Electrical Specifications – IDD Parameters
Table 10: IDD Specifications and Conditions – Revision G
Notes 1–3 apply to all parameters and conditions; VDD/VDDQ = 3.3V ±0.3V
Max
Parameter/Condition
Symbol
-6A
-7E
-75
Unit
Notes
Operating current: Active mode; Burst = 2; READ or
WRITE; tRC ≥ tRC (MIN)
IDD1
150
125
115
mA
4, 5, 6,
7
Standby current: Power-down mode; All banks idle; CKE
= LOW
IDD2
2
2
2
mA
7
Standby current: Active mode; CKE = HIGH; CS# = HIGH;
All banks active after tRCD met; No accesses in progress
IDD3
60
45
45
mA
4, 6, 7,
8
Operating current: Burst mode; Page burst; READ or
WRITE; All banks active
IDD4
180
150
140
mA
4, 5, 6,
7
Auto refresh current: CKE = HIGH; CS# tRFC = tRFC
= HIGH
(MIN)
IDD5
250
230
210
mA
4, 5, 6,
7, 8, 9
tRFC
Self refresh current: CKE ≤ 0.2V
Notes:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
IDD6
3
3
3
mA
tRFC
= 15.625μs
= 3.906μs
(AAT)
IDD6
6
6
6
mA
Standard
IDD7
1
1
1
mA
Low power (L)
IDD7
0.5
0.5
0.5
mA
10
1. All voltages referenced to VSS.
2. Minimum specifications are used only to indicate cycle time at which proper operation
over the full temperature range is ensured:
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +105°C (automotive)
3. An initial pause of 100μs is required after power-up, followed by two AUTO REFRESH
commands, before proper device operation is ensured. (VDD and VDDQ must be powered
up simultaneously. VSS and VSSQ must be at same potential.) The two AUTO REFRESH
command wake-ups should be repeated any time the tREF refresh requirement is exceeded.
4. IDD is dependent on output loading and cycle rates. Specified values are obtained with
minimum cycle time and the outputs open.
5. The IDD current will increase or decrease proportionally according to the amount of frequency alteration for the test condition.
6. Address transitions average one transition every two clocks.
7. For -75, CL = 3 and tCK = 7.5ns; for -7E, CL = 2 and tCK = 7.5ns; for -6, CL = 3 and tCK =
6ns.
8. Other input signals are allowed to transition no more than once every two clocks and
are otherwise at valid VIH or VIL levels.
9. CKE is HIGH during refresh command period tRFC (MIN) else CKE is LOW. The IDD6 limit is
actually a nominal value and does not result in a fail value.
10. Enables on-chip refresh and address counters.
21
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Electrical Specifications – IDD Parameters
Table 11: IDD Specifications and Conditions – Revision J
Notes 1–3 apply to all parameters and conditions; VDD/VDDQ = 3.3V ±0.3V
Max
Parameter/Condition
Symbol
-6A
-7E
-75
Unit
Notes
Operating current: Active mode; Burst = 2; READ or
WRITE; tRC ≥ tRC (MIN)
IDD1
TBD
TBD
TBD
mA
4, 5, 6,
7
Standby current: Power-down mode; All banks idle; CKE
= LOW
IDD2
TBD
TBD
TBD
mA
7
Standby current: Active mode; CKE = HIGH; CS# = HIGH;
All banks active after tRCD met; No accesses in progress
IDD3
TBD
TBD
TBD
mA
4, 6, 7,
8
Operating current: Burst mode; Page burst; READ or
WRITE; All banks active
IDD4
TBD
TBD
TBD
mA
4, 5, 6,
7
Auto refresh current: CKE = HIGH; CS# tRFC = tRFC
= HIGH
(MIN)
IDD5
TBD
TBD
TBD
mA
4, 5, 6,
7, 8, 9
tRFC
Self refresh current: CKE ≤ 0.2V
Notes:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
IDD6
TBD
TBD
TBD
mA
tRFC
= 15.625μs
= 3.906μs
(AAT)
IDD6
TBD
TBD
TBD
mA
Standard
IDD7
TBD
TBD
TBD
mA
Low power (L)
IDD7
TBD
TBD
TBD
mA
10
1. All voltages referenced to VSS.
2. Minimum specifications are used only to indicate cycle time at which proper operation
over the full temperature range is ensured:
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +105°C (automotive)
3. An initial pause of 100μs is required after power-up, followed by two AUTO REFRESH
commands, before proper device operation is ensured. (VDD and VDDQ must be powered
up simultaneously. VSS and VSSQ must be at same potential.) The two AUTO REFRESH
command wake-ups should be repeated any time the tREF refresh requirement is exceeded.
4. IDD is dependent on output loading and cycle rates. Specified values are obtained with
minimum cycle time and the outputs open.
5. The IDD current will increase or decrease proportionally according to the amount of frequency alteration for the test condition.
6. Address transitions average one transition every two clocks.
7. For -75, CL = 3 and tCK = 7.5ns; for -7E, CL = 2 and tCK = 7.5ns; for -6, CL = 3 and tCK =
6ns.
8. Other input signals are allowed to transition no more than once every two clocks and
are otherwise at valid VIH or VIL levels.
9. CKE is HIGH during refresh command period tRFC (MIN) else CKE is LOW. The IDD6 limit is
actually a nominal value and does not result in a fail value.
10. Enables on-chip refresh and address counters.
22
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Electrical Specifications – AC Operating Conditions
Electrical Specifications – AC Operating Conditions
Table 12: Electrical Characteristics and Recommended AC Operating Conditions
Notes 1–5 apply to all parameters and conditions
-6A6, 7
-6
-7E
-75
Symbol
Min
Max
Min
Max
Min
Max
Min
Max
Unit
Note
s
CL = 3
tAC(3)
–
5.4
–
5.5
–
5.4
–
5.4
ns
8
CL = 2
tAC(2)
–
7.5
–
7.5
–
5.4
–
6
ns
8
CL = 1
tAC(1)
–
17
–
17
–
–
–
–
ns
8
Address hold time
tAH
0.8
–
1
–
0.8
–
0.8
–
ns
Address setup time
tAS
1.5
–
1.5
–
1.5
–
1.5
–
ns
CLK high-level width
tCH
2.5
–
2.5
–
2.5
–
2.5
–
ns
CLK low-level width
tCL
2.5
–
2.5
–
2.5
–
ns
Parameter
Access time from
CLK (positive
edge)
2.5
–
CL = 3
tCK(3)
6
–
6
–
7
–
7.5
–
ns
9
CL = 2
tCK(2)
10
–
10
–
7.5
–
10
–
ns
9
CL = 1
tCK(1)
20
–
20
–
–
–
–
–
ns
9
CKE hold time
tCKH
0.8
–
1
–
0.8
–
0.8
–
ns
CKE setup time
tCKS
1.5
–
1.5
–
1.5
–
1.5
–
ns
CS#, RAS#, CAS#, WE#,
DQM hold time
tCMH
0.8
1
–
0.8
–
0.8
–
ns
CS#, RAS#, CAS#, WE#,
DQM setup time
tCMS
1.5
–
1.5
–
1.5
–
1.5
–
ns
Data-in hold time
tDH
0.8
–
1
–
0.8
–
0.8
–
ns
Data-in setup time
tDS
1.5
–
1.5
–
1.5
–
1.5
–
ns
CL = 3
tHZ(3)
–
5.4
–
5.5
–
5.4
–
5.4
ns
10
CL = 2
tHZ(2)
–
7.5
–
7.5
–
5.4
–
6
ns
10
CL = 1
tHZ(1)
–
17
–
17
–
–
–
–
ns
10
Data-out Low-Z time
tLZ
1
–
1
–
1
–
1
–
ns
Data-out hold time
(load)
tOH
3
–
2
–
3
–
3
–
ns
Data-out hold time (no
load)
tOHn
1.8
–
1.8
–
1.8
–
1.8
–
ns
ACTIVE-to-PRECHARGE
command
tRAS
42
120,000
42
120,000
37
120,000
44
120,000
ns
ACTIVE-to-ACTIVE command period
tRC
60
–
60
–
60
–
66
–
ns
ACTIVE-to-READ or
WRITE delay
tRCD
18
–
18
–
15
–
20
–
ns
Refresh period (4096
rows)
tREF
–
64
–
64
–
64
–
64
ms
–
16
–
16
–
16
–
16
ms
60
–
60
–
66
–
66
–
ns
Clock cycle time
Data-out High-Z
time
Refresh period – automotive (4096 rows)
AUTO REFRESH period
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
tREF
AT
tRFC
23
11
12
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Electrical Specifications – AC Operating Conditions
Table 12: Electrical Characteristics and Recommended AC Operating Conditions (Continued)
Notes 1–5 apply to all parameters and conditions
-6A6, 7
Parameter
-6
-7E
-75
Note
s
Symbol
Min
Max
Min
Max
Min
Max
Min
Max
Unit
tRP
18
–
18
–
15
–
20
–
ns
tRRD
12
–
12
–
14
–
15
–
ns
tT
0.3
1.2
0.3
1.2
0.3
1.2
0.3
1.2
ns
13
WRITE recovery time
tWR
1 CLK +
6ns
–
1 CLK +
6ns
–
1 CLK +
7ns
–
1 CLK +
7.5ns
–
ns
14
12
–
12
–
14
–
15
–
Exit SELF REFRESH-to-ACTIVE command
tXSR
67
–
70
–
67
–
75
–
PRECHARGE command
period
ACTIVE bank a to ACTIVE
bank b command
Transition time
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
24
15
ns
16
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Electrical Specifications – AC Operating Conditions
Table 13: AC Functional Characteristics
Notes 1–6 apply to all parameters and conditions
Symbol
-6/-6A
-7E
-75
Unit
Note
s
Last data-in to burst STOP command
tBDL
1
1
1
tCK
17
READ/WRITE command to READ/WRITE command
tCCD
1
1
1
tCK
17
Last data-in to new READ/WRITE command
tCDL
1
tCK
17
1
tCK
18
19,
20
Parameter
tCKED
CKE to clock disable or power-down entry mode
1
1
1
1
Data-in to ACTIVE command
tDAL
5
4
5
tCK
Data-in to PRECHARGE command
tDPL
2
2
2
tCK
20,
21
DQM to input data delay
tDQD
0
0
0
tCK
17
DQM to data mask during WRITEs
tDQM
0
tCK
17
DQM to data High-Z during READs
tDQZ
2
2
2
tCK
17
WRITE command to input data delay
tDWD
0
0
0
tCK
17
LOAD MODE REGISTER command to ACTIVE or REFRESH command
tMRD
2
tCK
22
CKE to clock enable or power-down exit setup mode
tPED
1
tCK
17
Last data-in to PRECHARGE command
tRDL
2
2
2
tCK
20,
21
CL = 3
tROH(3)
3
3
3
tCK
17
CL = 2
tROH(2)
2
tCK
17
CL = 1
tROH(1)
–
tCK
17
Data-out High-Z from PRECHARGE command
Notes:
0
2
1
2
1
0
2
1
2
–
1. Minimum specifications are used only to indicate cycle time at which proper operation
over the full temperature range is ensured:
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +105°C (automotive)
2. An initial pause of 100μs is required after power-up, followed by two AUTO REFRESH
commands, before proper device operation is ensured. (VDD and VDDQ must be powered
up simultaneously. VSS and VSSQ must be at same potential.) The two AUTO REFRESH
command wake-ups should be repeated any time the tREF refresh requirement is exceeded.
3. In addition to meeting the transition rate specification, the clock and CKE must transit
between VIH and VIL (or between VIL and VIH) in a monotonic manner.
4. Outputs measured at 1.5V with equivalent load:
Q
50pF
5. AC operating and IDD test conditions have VIL = 0V and VIH = 3.0V using a measurement
reference level of 1.5V. If the input transition time is longer than 1ns, then the timing is
measured from VIL,max and VIH,min and no longer from the 1.5V midpoint. CLK should always be 1.5V referenced to crossover. Refer to Micron technical note TN-48-09.
6. The -6A speed grade is not backward compatible with -7E at CL = 2.
7. Not applicable for Revision G.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
25
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Electrical Specifications – AC Operating Conditions
8. tAC for -75/-7E at CL = 3 with no load is 4.6ns and is guaranteed by design.
9. The clock frequency must remain constant (stable clock is defined as a signal cycling
within timing constraints specified for the clock pin) during access or precharge states
(READ, WRITE, including tWR, and PRECHARGE commands). CKE may be used to reduce
the data rate.
10. tHZ defines the time at which the output achieves the open circuit condition; it is not a
reference to VOH or VOL. The last valid data element will meet tOH before going High-Z.
11. Parameter guaranteed by design.
12. DRAM devices should be evenly addressed when being accessed. Disproportionate accesses to a particular row address may result in reduction of the product lifetime.
13. AC characteristics assume tT = 1ns.
14. Auto precharge mode only. The precharge timing budget (tRP) begins at 6ns for -6, at
7ns for -7E, and 7.5ns for -75 after the first clock delay and after the last WRITE is executed.
15. Precharge mode only.
16. CLK must be toggled a minimum of two times during this period.
17. Required clocks are specified by JEDEC functionality and are not dependent on any timing parameter.
18. Timing specified by tCKS. Clock(s) specified as a reference only at minimum cycle rate.
19. Timing is specified by tWR plus tRP. Clock(s) specified as a reference only at minimum cycle rate.
20. Based on tCK = 7.5ns for -75 and -7E, 6ns for -6.
21. Timing is specified by tWR.
22. JEDEC and PC100 specify three clocks.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
26
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Functional Description
Functional Description
In general, 64Mb SDRAM devices (2 Meg x 8 x 4 banks, and 1 Meg x 16 x 4 banks) are
quad-bank DRAM that operate at 3.3V and include a synchronous interface. All signals
are registered on the positive edge of the clock signal, CLK. Each of the x8’s 16,777,216bit banks is organized as 4096 rows by 512 columns by 8 bits. Each of the x16’s
16,777,216-bit banks is organized as 4096 rows by 256 columns by 16 bits.
Read and write accesses to the SDRAM are burst-oriented; accesses start at a selected
location and continue for a programmed number of locations in a programmed sequence. Accesses begin with the registration of an ACTIVE command, followed by a
READ or WRITE command. The address bits registered coincident with the ACTIVE
command are used to select the bank and row to be accessed (BA0 and BA1 select the
bank, A[11:0] select the row). The address bits (x8: A[8:0]; x16: A[7:0]) registered coincident with the READ or WRITE command are used to select the starting column location
for the burst access.
Prior to normal operation, the device must be initialized. The following sections provide
detailed information covering device initialization, register definition, command descriptions, and device operation.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
27
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Commands
Commands
The following table provides a quick reference of available commands, followed by a
written description of each command. Additional Truth Tables (Table 15 (page 33), Table 16 (page 35), and Table 17 (page 37)) provide current state/next state information.
Table 14: Truth Table – Commands and DQM Operation
Note 1 applies to all parameters and conditions
Name (Function)
CS# RAS# CAS# WE# DQM
ADDR
DQ
Notes
COMMAND INHIBIT (NOP)
H
X
X
X
X
X
X
NO OPERATION (NOP)
L
H
H
H
X
X
X
ACTIVE (select bank and activate row)
L
L
H
H
X
Bank/row
X
2
READ (select bank and column, and start READ burst)
L
H
L
H
L/H
Bank/col
X
3
WRITE (select bank and column, and start WRITE burst)
L
H
L
L
L/H
Bank/col
Valid
3
BURST TERMINATE
L
H
H
L
X
X
Active
4
PRECHARGE (Deactivate row in bank or banks)
L
L
H
L
X
Code
X
5
AUTO REFRESH or SELF REFRESH (enter self refresh mode)
L
L
L
H
X
X
X
6, 7
LOAD MODE REGISTER
L
L
L
L
X
Op-code
X
8
Write enable/output enable
X
X
X
X
L
X
Active
9
Write inhibit/output High-Z
X
X
X
X
H
X
High-Z
9
Notes:
1. CKE is HIGH for all commands shown except SELF REFRESH.
2. A[0:n] provide row address (where An is the most significant address bit), BA0 and BA1
determine which bank is made active.
3. A[0:i] provide column address (where i = the most significant column address for a given
device configuration). A10 HIGH enables the auto precharge feature (nonpersistent),
while A10 LOW disables the auto precharge feature. BA0 and BA1 determine which
bank is being read from or written to.
4. The purpose of the BURST TERMINATE command is to stop a data burst, thus the command could coincide with data on the bus. However, the DQ column reads a “Don’t
Care” state to illustrate that the BURST TERMINATE command can occur when there is
no data present.
5. A10 LOW: BA0, BA1 determine the bank being precharged. A10 HIGH: all banks precharged and BA0, BA1 are “Don’t Care.”
6. This command is AUTO REFRESH if CKE is HIGH, SELF REFRESH if CKE is LOW.
7. Internal refresh counter controls row addressing; all inputs and I/Os are “Don’t Care” except for CKE.
8. A[11:0] define the op-code written to the mode register.
9. Activates or deactivates the DQ during WRITEs (zero-clock delay) and READs (two-clock
delay).
COMMAND INHIBIT
The COMMAND INHIBIT function prevents new commands from being executed by
the device, regardless of whether the CLK signal is enabled. The device is effectively deselected. Operations already in progress are not affected.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
28
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Commands
NO OPERATION (NOP)
The NO OPERATION (NOP) command is used to perform a NOP to the selected device
(CS# is LOW). This prevents unwanted commands from being registered during idle or
wait states. Operations already in progress are not affected.
LOAD MODE REGISTER (LMR)
The mode registers are loaded via inputs A[n:0] (where An is the most significant address term), BA0, and BA1(see (page 0 )). The LOAD MODE REGISTER command can
only be issued when all banks are idle and a subsequent executable command cannot
be issued until tMRD is met.
ACTIVE
The ACTIVE command is used to activate a row in a particular bank for a subsequent
access. The value on the BA0, BA1 inputs selects the bank, and the address provided selects the row. This row remains active for accesses until a PRECHARGE command is issued to that bank. A PRECHARGE command must be issued before opening a different
row in the same bank.
Figure 9: ACTIVE Command
CLK
CKE
HIGH
CS#
RAS#
CAS#
WE#
Address
Row address
BA0, BA1
Bank address
Don’t Care
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
29
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Commands
READ
The READ command is used to initiate a burst read access to an active row. The values
on the BA0 and BA1 inputs select the bank; the address provided selects the starting column location. The value on input A10 determines whether auto precharge is used. If auto precharge is selected, the row being accessed is precharged at the end of the READ
burst; if auto precharge is not selected, the row remains open for subsequent accesses.
Read data appears on the DQ subject to the logic level on the DQM inputs two clocks
earlier. If a given DQM signal was registered HIGH, the corresponding DQ will be HighZ two clocks later; if the DQM signal was registered LOW, the DQ will provide valid data.
Figure 10: READ Command
CLK
CKE
HIGH
CS#
RAS#
CAS#
WE#
Address
A101
Column address
EN AP
DIS AP
BA0, BA1
Bank address
Don’t Care
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1. EN AP = enable auto precharge, DIS AP = disable auto precharge.
30
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Commands
WRITE
The WRITE command is used to initiate a burst write access to an active row. The values
on the BA0 and BA1 inputs select the bank; the address provided selects the starting column location. The value on input A10 determines whether auto precharge is used. If auto precharge is selected, the row being accessed is precharged at the end of the write
burst; if auto precharge is not selected, the row remains open for subsequent accesses.
Input data appearing on the DQ is written to the memory array, subject to the DQM input logic level appearing coincident with the data. If a given DQM signal is registered
LOW, the corresponding data is written to memory; if the DQM signal is registered
HIGH, the corresponding data inputs are ignored and a WRITE is not executed to that
byte/column location.
Figure 11: WRITE Command
CLK
CKE
HIGH
CS#
RAS#
CAS#
WE#
Address
A101
Column address
EN AP
DIS AP
BA0, BA1
Bank address
Valid address
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
Don’t Care
1. EN AP = enable auto precharge, DIS AP = disable auto precharge.
31
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Commands
PRECHARGE
The PRECHARGE command is used to deactivate the open row in a particular bank or
the open row in all banks. The bank(s) will be available for a subsequent row access a
specified time (tRP) after the PRECHARGE command is issued. Input A10 determines
whether one or all banks are to be precharged, and in the case where only one bank is
precharged, inputs BA0 and BA1 select the bank. Otherwise BA0 and BA1 are treated as
“Don’t Care.” After a bank has been precharged, it is in the idle state and must be activated prior to any READ or WRITE commands are issued to that bank.
Figure 12: PRECHARGE Command
CLK
CKE
HIGH
CS#
RAS#
CAS#
WE#
Address
All banks
A10
Bank selected
BA0, BA1
Bank address
Valid address
Don’t Care
BURST TERMINATE
The BURST TERMINATE command is used to truncate either fixed-length or continuous page bursts. The most recently registered READ or WRITE command prior to the
BURST TERMINATE command is truncated.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
32
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Truth Tables
Truth Tables
Table 15: Truth Table – Current State Bank n, Command to Bank n
Notes 1–6 apply to all parameters and conditions
Current State
CS# RAS# CAS#
Any
Idle
Row active
Read
(auto precharge disabled)
Write
(auto precharge disabled)
Notes:
WE# Command/Action
Notes
H
X
X
X
COMMAND INHIBIT (NOP/continue previous operation)
L
H
H
H
NO OPERATION (NOP/continue previous operation)
L
L
H
H
ACTIVE (select and activate row)
L
L
L
H
AUTO REFRESH
7
L
L
L
L
LOAD MODE REGISTER
7
L
L
H
L
PRECHARGE
8
L
H
L
H
READ (select column and start READ burst)
9
L
H
L
L
WRITE (select column and start WRITE burst)
9
L
L
H
L
PRECHARGE (deactivate row in bank or banks)
10
L
H
L
H
READ (select column and start new READ burst)
9
L
H
L
L
WRITE (select column and start WRITE burst)
9
L
L
H
L
PRECHARGE (truncate READ burst, start PRECHARGE)
10
L
H
H
L
BURST TERMINATE
11
L
H
L
H
READ (select column and start READ burst)
9
L
H
L
L
WRITE (select column and start new WRITE burst)
9
L
L
H
L
PRECHARGE (truncate WRITE burst, start PRECHARGE)
10
L
H
H
L
BURST TERMINATE
11
1. This table applies when CKEn-1 was HIGH and CKEn is HIGH (see Table 17 (page 37))
and after tXSR has been met (if the previous state was self refresh).
2. This table is bank-specific, except where noted (for example, the current state is for a
specific bank and the commands shown can be issued to that bank when in that state).
Exceptions are covered below.
3. Current state definitions:
Idle: The bank has been precharged, and tRP has been met.
Row active: A row in the bank has been activated, and tRCD has been met. No data
bursts/accesses and no register accesses are in progress.
Read: A READ burst has been initiated, with auto precharge disabled, and has not yet
terminated or been terminated.
Write: A WRITE burst has been initiated, with auto precharge disabled, and has not yet
terminated or been terminated.
4. The following states must not be interrupted by a command issued to the same bank.
COMMAND INHIBIT or NOP commands, or supported commands to the other bank
should be issued on any clock edge occurring during these states. Supported commands
to any other bank are determined by the bank’s current state and the conditions described in this and the following table.
Precharging: Starts with registration of a PRECHARGE command and ends when tRP is
met. After tRP is met, the bank will be in the idle state.
Row activating: Starts with registration of an ACTIVE command and ends when tRCD is
met. After tRCD is met, the bank will be in the row active state.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
33
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Truth Tables
Read with auto precharge enabled: Starts with registration of a READ command
with auto precharge enabled and ends when tRP has been met. After tRP is met, the
bank will be in the idle state.
Write with auto precharge enabled: Starts with registration of a WRITE command
with auto precharge enabled and ends when tRP has been met. After tRP is met, the
bank will be in the idle state.
5. The following states must not be interrupted by any executable command; COMMAND
INHIBIT or NOP commands must be applied on each positive clock edge during these
states.
Refreshing: Starts with registration of an AUTO REFRESH command and ends when
tRFC is met. After tRFC is met, the device will be in the all banks idle state.
Accessing mode register: Starts with registration of a LOAD MODE REGISTER command and ends when tMRD has been met. After tMRD is met, the device will be in the
all banks idle state.
6.
7.
8.
9.
10.
11.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
Precharging all: Starts with registration of a PRECHARGE ALL command and ends
when tRP is met. After tRP is met, all banks will be in the idle state.
All states and sequences not shown are illegal or reserved.
Not bank specific; requires that all banks are idle.
Does not affect the state of the bank and acts as a NOP to that bank.
READs or WRITEs listed in the Command/Action column include READs or WRITEs with
auto precharge enabled and READs or WRITEs with auto precharge disabled.
May or may not be bank specific; if all banks need to be precharged, each must be in a
valid state for precharging.
Not bank-specific; BURST TERMINATE affects the most recent READ or WRITE burst, regardless of bank.
34
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Truth Tables
Table 16: Truth Table – Current State Bank n, Command to Bank m
Notes 1–6 apply to all parameters and conditions
Current State
CS# RAS# CAS#
Any
WE# Command/Action
H
X
X
X
COMMAND INHIBIT (NOP/continue previous operation)
L
H
H
H
NO OPERATION (NOP/continue previous operation)
Idle
X
X
X
X
Any command otherwise supported for bank m
Row activating, active, or
precharging
L
L
H
H
ACTIVE (select and activate row)
Read
(auto precharge disabled)
Write
(auto precharge disabled)
Read
(with auto precharge)
Write
(with auto precharge)
Notes:
Notes
L
H
L
H
READ (select column and start READ burst)
7
L
H
L
L
WRITE (select column and start WRITE burst)
7
L
L
H
L
PRECHARGE
L
L
H
H
ACTIVE (select and activate row)
L
H
L
H
READ (select column and start new READ burst)
7, 10
L
H
L
L
WRITE (select column and start WRITE burst)
7, 11
L
L
H
L
PRECHARGE
L
L
H
H
ACTIVE (select and activate row)
L
H
L
H
READ (select column and start READ burst)
7, 12
L
H
L
L
WRITE (select column and start new WRITE burst)
7, 13
L
L
H
L
PRECHARGE
L
L
H
H
ACTIVE (select and activate row)
L
H
L
H
READ (select column and start new READ burst)
7, 8, 14
L
H
L
L
WRITE (select column and start WRITE burst)
7, 8, 15
L
L
H
L
PRECHARGE
L
L
H
H
ACTIVE (select and activate row)
L
H
L
H
READ (select column and start READ burst)
7, 8, 16
L
H
L
L
WRITE (select column and start new WRITE burst)
7, 8, 17
L
L
H
L
PRECHARGE
9
9
9
9
1. This table applies when CKEn-1 was HIGH and CKEn is HIGH (Table 17 (page 37)), and
after tXSR has been met (if the previous state was self refresh).
2. This table describes alternate bank operation, except where noted; for example, the current state is for bank n and the commands shown can be issued to bank m, assuming
that bank m is in such a state that the given command is supported. Exceptions are covered below.
3. Current state definitions:
Idle: The bank has been precharged, and tRP has been met.
Row active: A row in the bank has been activated, and tRCD has been met. No data
bursts/accesses and no register accesses are in progress.
Read: A READ burst has been initiated, with auto precharge disabled, and has not yet
terminated or been terminated.
Write: A WRITE burst has been initiated, with auto precharge disabled, and has not yet
terminated or been terminated.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
35
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Truth Tables
Read with auto precharge enabled: Starts with registration of a READ command
with auto precharge enabled and ends when tRP has been met. After tRP is met, the
bank will be in the idle state.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
Write with auto precharge enabled: Starts with registration of a WRITE command
with auto precharge enabled and ends when tRP has been met. After tRP is met, the
bank will be in the idle state.
AUTO REFRESH, SELF REFRESH, and LOAD MODE REGISTER commands can only be issued when all banks are idle.
A BURST TERMINATE command cannot be issued to another bank; it applies to the bank
represented by the current state only.
All states and sequences not shown are illegal or reserved.
READs or WRITEs to bank m listed in the Command/Action column include READs or
WRITEs with auto precharge enabled and READs or WRITEs with auto precharge disabled.
Concurrent auto precharge: Bank n will initiate the auto precharge command when its
burst has been interrupted by bank m burst.
The burst in bank n continues as initiated.
For a READ without auto precharge interrupted by a READ (with or without auto precharge), the READ to bank m will interrupt the READ on bank n, CAS latency (CL) later.
For a READ without auto precharge interrupted by a WRITE (with or without auto precharge), the WRITE to bank m will interrupt the READ on bank n when registered. DQM
should be used one clock prior to the WRITE command to prevent bus contention.
For a WRITE without auto precharge interrupted by a READ (with or without auto precharge), the READ to bank m will interrupt the WRITE on bank n when registered, with
the data-out appearing CL later. The last valid WRITE to bank n will be data-in registered one clock prior to the READ to bank m.
For a WRITE without auto precharge interrupted by a WRITE (with or without auto precharge), the WRITE to bank m will interrupt the WRITE on bank n when registered. The
last valid WRITE to bank n will be data-in registered one clock prior to the READ to bank
m.
For a READ with auto precharge interrupted by a READ (with or without auto precharge), the READ to bank m will interrupt the READ on bank n, CL later. The PRECHARGE to bank n will begin when the READ to bank m is registered.
For a READ with auto precharge interrupted by a WRITE (with or without auto precharge), the WRITE to bank m will interrupt the READ on bank n when registered. DQM
should be used two clocks prior to the WRITE command to prevent bus contention. The
PRECHARGE to bank n will begin when the WRITE to bank m is registered.
For a WRITE with auto precharge interrupted by a READ (with or without auto precharge), the READ to bank m will interrupt the WRITE on bank n when registered, with
the data-out appearing CL later. The PRECHARGE to bank n will begin after tWR is met,
where tWR begins when the READ to bank m is registered. The last valid WRITE bank n
will be data-in registered one clock prior to the READ to bank m.
For a WRITE with auto precharge interrupted by a WRITE (with or without auto precharge), the WRITE to bank m will interrupt the WRITE on bank n when registered. The
PRECHARGE to bank n will begin after tWR is met, where tWR begins when the WRITE
to bank m is registered. The last valid WRITE to bank n will be data registered one clock
to the WRITE to bank m.
36
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Truth Tables
Table 17: Truth Table – CKE
Notes 1–4 apply to all parameters and conditions
Current State
CKEn-1
CKEn
Power-down
L
Commandn
Actionn
X
Maintain power-down
X
Maintain self refresh
L
Self refresh
Clock suspend
Power-down
L
H
Self refresh
X
Maintain clock suspend
COMMAND INHIBIT or NOP
Exit power-down
5
COMMAND INHIBIT or NOP
Exit self refresh
6
X
Exit clock suspend
7
COMMAND INHIBIT or NOP
Power-down entry
AUTO REFRESH
Self refresh entry
VALID
Clock suspend entry
Clock suspend
All banks idle
H
L
All banks idle
Reading or writing
H
Notes:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
H
Notes
See Table 16 (page 35).
1. CKEn is the logic state of CKE at clock edge n; CKEn-1 was the state of CKE at the previous clock edge.
2. Current state is the state of the SDRAM immediately prior to clock edge n.
3. COMMANDn is the command registered at clock edge n, and ACTIONn is a result of
COMMANDn.
4. All states and sequences not shown are illegal or reserved.
5. Exiting power-down at clock edge n will put the device in the all banks idle state in time
for clock edge n + 1 (provided that tCKS is met).
6. Exiting self refresh at clock edge n will put the device in the all banks idle state after
tXSR is met. COMMAND INHIBIT or NOP commands should be issued on any clock edges
occurring during the tXSR period. A minimum of two NOP commands must be provided
during the tXSR period.
7. After exiting clock suspend at clock edge n, the device will resume operation and recognize the next command at clock edge n + 1.
37
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Initialization
Initialization
SDRAM must be powered up and initialized in a predefined manner. Operational procedures other than those specified may result in undefined operation. After power is applied to V DD and V DDQ (simultaneously) and the clock is stable (stable clock is defined
as a signal cycling within timing constraints specified for the clock pin), the SDRAM requires a 100μs delay prior to issuing any command other than a COMMAND INHIBIT or
NOP. Starting at some point during this 100μs period and continuing at least through
the end of this period, COMMAND INHIBIT or NOP commands must be applied.
After the 100μs delay has been satisfied with at least one COMMAND INHIBIT or NOP
command having been applied, a PRECHARGE command should be applied. All banks
must then be precharged, thereby placing the device in the all banks idle state.
Once in the idle state, at least two AUTO REFRESH cycles must be performed. After the
AUTO REFRESH cycles are complete, the SDRAM is ready for mode register programming. Because the mode register will power up in an unknown state, it must be loaded
prior to applying any operational command. If desired, the two AUTO REFRESH commands can be issued after the LMR command.
The recommended power-up sequence for SDRAM:
1. Simultaneously apply power to V DD and V DDQ.
2. Assert and hold CKE at a LVTTL logic LOW since all inputs and outputs are LVTTLcompatible.
3. Provide stable CLOCK signal. Stable clock is defined as a signal cycling within timing constraints specified for the clock pin.
4. Wait at least 100μs prior to issuing any command other than a COMMAND INHIBIT or NOP.
5. Starting at some point during this 100μs period, bring CKE HIGH. Continuing at
least through the end of this period, 1 or more COMMAND INHIBIT or NOP commands must be applied.
6. Perform a PRECHARGE ALL command.
7. Wait at least tRP time; during this time NOPs or DESELECT commands must be
given. All banks will complete their precharge, thereby placing the device in the all
banks idle state.
8. Issue an AUTO REFRESH command.
9. Wait at least tRFC time, during which only NOPs or COMMAND INHIBIT commands are allowed.
10. Issue an AUTO REFRESH command.
11. Wait at least tRFC time, during which only NOPs or COMMAND INHIBIT commands are allowed.
12. The SDRAM is now ready for mode register programming. Because the mode register will power up in an unknown state, it should be loaded with desired bit values
prior to applying any operational command. Using the LMR command, program
the mode register. The mode register is programmed via the MODE REGISTER SET
command with BA1 = 0, BA0 = 0 and retains the stored information until it is programmed again or the device loses power. Not programming the mode register
upon initialization will result in default settings which may not be desired. Outputs are guaranteed High-Z after the LMR command is issued. Outputs should be
High-Z already before the LMR command is issued.
13. Wait at least tMRD time, during which only NOP or DESELECT commands are allowed.
At this point the DRAM is ready for any valid command.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
38
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Initialization
Note:
More than two AUTO REFRESH commands can be issued in the sequence. After steps 9
and 10 are complete, repeat them until the desired number of AUTO REFRESH + tRFC
loops is achieved.
Figure 13: Initialize and Load Mode Register
T0
CK
((
))
T1
tCK
((
))
((
))
tCKS tCKH
Tn + 1
tCH
To + 1
((
))
((
))
tCL
((
))
((
))
((
))
Tp + 2
Tp + 3
((
))
CKE
((
))
((
))
COMMAND
((
))
((
))
DQM/DQML,
DQMU
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
A[9:0],
A[12:11]
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
A10
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
tRFC
tRFC
((
))
((
))
Tp + 1
tCMS tCMH
BA[1:0]
DQ
NOP2
ALL BANKS
SINGLE BANK
((
))
((
))
((
))
T = 100µs
MIN
PRECHARGE
ALL
BANKS
High-Z
((
))
((
))
AUTO
REFRESH
((
))
NOP2
((
))
AUTO
REFRESH
((
))
NOP2
((
))
LOAD MODE
REGISTER
tAS
NOP2
tAH5
ROW
CODE
tAS
ACTIVE
tAH
ROW
CODE
((
))
tRP
Power-up:
VDD and
CLK stable
Precharge
all banks
AUTO REFRESH
AUTO REFRESH
tMRD
Program Mode Register1,3,4
DON’T CARE
UNDEFINED
Notes:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1.
2.
3.
4.
5.
The mode register may be loaded prior to the AUTO REFRESH cycles if desired.
If CS is HIGH at clock HIGH time, all commands applied are NOP.
JEDEC and PC100 specify three clocks.
Outputs are guaranteed High-Z after command is issued.
A12 should be a LOW at tP + 1.
39
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Mode Register
Mode Register
The mode register defines the specific mode of operation, including burst length (BL),
burst type, CAS latency (CL), operating mode, and write burst mode. The mode register
is programmed via the LOAD MODE REGISTER command and retains the stored information until it is programmed again or the device loses power.
Mode register bits M[2:0] specify the BL; M3 specifies the type of burst; M[6:4] specify
the CL; M7 and M8 specify the operating mode; M9 specifies the write burst mode; and
M10–Mn should be set to zero to ensure compatibility with future revisions. Mn + 1 and
Mn + 2 should be set to zero to select the mode register.
The mode registers must be loaded when all banks are idle, and the controller must wait
tMRD before initiating the subsequent operation. Violating either of these requirements
will result in unspecified operation.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
40
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Mode Register
Figure 14: Mode Register Definition
A12 A11 A10
12
11
10
A9
8
9
WB
Reserved
A8
7
Op Mode
A5
A6
A7
A4
5
6
A3
3
4
CAS Latency
Program
BA1, BA0 = “0, 0”
to ensure compatibility
with future devices.
A0
0
Address Bus
Mode Register (Mx)
Burst Length
Burst Length
M2 M1 M0
Write Burst Mode
M9
1
2
BT
A1
A2
0
Programmed Burst Length
1
Single Location Access
M3 = 0
M3 = 1
0
0
0
1
1
0
0
1
2
2
0
1
0
4
4
0
1
1
8
8
1
0
0
Reserved
Reserved
M8
M7
M6-M0
Operating Mode
1
0
1
Reserved
Reserved
0
0
Defined
Standard Operation
1
1
0
Reserved
Reserved
–
–
–
All other states reserved
1
1
1
Full Page
Reserved
M3
0
Sequential
1
Interleaved
CAS Latency
M6 M5 M4
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
Burst Type
0
0
0
Reserved
0
0
1
1
0
1
0
2
0
1
1
3
1
0
0
Reserved
1
0
1
Reserved
1
1
0
Reserved
1
1
1
Reserved
41
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Mode Register
Burst Length
Read and write accesses to the device are burst oriented, and the burst length (BL) is
programmable. The burst length determines the maximum number of column locations that can be accessed for a given READ or WRITE command. Burst lengths of 1, 2,
4, 8, or continuous locations are available for both the sequential and the interleaved
burst types, and a continuous page burst is available for the sequential type. The continuous page burst is used in conjunction with the BURST TERMINATE command to
generate arbitrary burst lengths.
Reserved states should not be used, as unknown operation or incompatibility with future versions may result.
When a READ or WRITE command is issued, a block of columns equal to the burst
length is effectively selected. All accesses for that burst take place within this block,
meaning that the burst wraps within the block when a boundary is reached. The block
is uniquely selected by A[8:1] when BL = 2, A[8:2] when BL = 4, and A[8:3] when BL = 8.
The remaining (least significant) address bit(s) is (are) used to select the starting location within the block. Continuous page bursts wrap within the page when the boundary
is reached.
Burst Type
Accesses within a given burst can be programmed to be either sequential or interleaved;
this is referred to as the burst type and is selected via bit M3.
The ordering of accesses within a burst is determined by the burst length, the burst
type, and the starting column address.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
42
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Mode Register
Table 18: Burst Definition Table
Order of Accesses Within a Burst
Burst Length
Starting Column Address
2
Type = Interleaved
0
0-1
0-1
1
1-0
1-0
A0
4
8
Type = Sequential
A1
A0
0
0
0-1-2-3
0-1-2-3
0
1
1-2-3-0
1-0-3-2
1
0
2-3-0-1
2-3-0-1
1
1
3-0-1-2
3-2-1-0
A2
A1
A0
0
0
0
0-1-2-3-4-5-6-7
0-1-2-3-4-5-6-7
0
0
1
1-2-3-4-5-6-7-0
1-0-3-2-5-4-7-6
0
1
0
2-3-4-5-6-7-0-1
2-3-0-1-6-7-4-5
0
1
1
3-4-5-6-7-0-1-2
3-2-1-0-7-6-5-4
1
0
0
4-5-6-7-0-1-2-3
4-5-6-7-0-1-2-3
1
0
1
5-6-7-0-1-2-3-4
5-4-7-6-1-0-3-2
1
1
0
6-7-0-1-2-3-4-5
6-7-4-5-2-3-0-1
1
1
1
7-0-1-2-3-4-5-6
7-6-5-4-3-2-1-0
Cn, Cn + 1, Cn + 2, Cn + 3...Cn - 1,
Cn...
Not supported
Continuous
n = A0–An/9/8 (location 0–y)
Notes:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1. For full-page accesses: y = 1024 (x8); y = 512 (x16).
2. For BL = 2, A1–A9 (x8); or A1–A8 (x16) select the block-of-two burst; A0 selects the starting column within the block.
3. For BL = 4, A2–A9 (x8); or A2–A8 (x16) select the block-of-four burst; A0–A1 select the
starting column within the block.
4. For BL = 8, A3–A9 (x8); or A3–A8 (x16) select the block-of-eight burst; A0–A2 select the
starting column within the block.
5. For a full-page burst, the full row is selected and A0–A9 (x8); or A0–A8 (x16) select the
starting column.
6. Whenever a boundary of the block is reached within a given sequence above, the following access wraps within the block.
7. For BL = 1, A0–A9 (x8); or A0–A8 (x16) select the unique column to be accessed, and
mode register bit M3 is ignored.
43
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Mode Register
CAS Latency
The CAS latency (CL) is the delay, in clock cycles, between the registration of a READ
command and the availability of the output data. The latency can be set to two or three
clocks.
If a READ command is registered at clock edge n, and the latency is m clocks, the data
will be available by clock edge n + m. The DQ start driving as a result of the clock edge
one cycle earlier (n + m - 1), and provided that the relevant access times are met, the
data is valid by clock edge n + m. For example, assuming that the clock cycle time is
such that all relevant access times are met, if a READ command is registered at T0 and
the latency is programmed to two clocks, the DQ start driving after T1 and the data is
valid by T2.
Reserved states should not be used as unknown operation or incompatibility with future versions may result.
Figure 15: CAS Latency
T0
T1
T2
T3
NOP
NOP
CLK
Command
READ
tOH
tLZ
DQ
tAC
DOUT
CL = 2
T0
T1
T2
T3
T4
NOP
NOP
NOP
CLK
Command
READ
tOH
tLZ
DQ
CL = 3
tAC
Don’t Care
DOUT
Undefined
Operating Mode
The normal operating mode is selected by setting M7 and M8 to zero; the other combinations of values for M7 and M8 are reserved for future use. Reserved states should not
be used because unknown operation or incompatibility with future versions may result.
Write Burst Mode
When M9 = 0, the burst length programmed via M[2:0] applies to both READ and
WRITE bursts; when M9 = 1, the programmed burst length applies to READ bursts, but
write accesses are single-location (nonburst) accesses.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
44
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Bank/Row Activation
Bank/Row Activation
Before any READ or WRITE commands can be issued to a bank within the SDRAM, a
row in that bank must be opened. This is accomplished via the ACTIVE command,
which selects both the bank and the row to be activated.
After a row is opened with the ACTIVE command, a READ or WRITE command can be
issued to that row, subject to the tRCD specification. tRCD (MIN) should be divided by
the clock period and rounded up to the next whole number to determine the earliest
clock edge after the ACTIVE command on which a READ or WRITE command can be
entered. For example, a tRCD specification of 20ns with a 125 MHz clock (8ns period)
results in 2.5 clocks, rounded to 3. This is reflected in Figure 16 (page 45), which covers
any case where 2 < tRCD (MIN)/tCK ≤ 3. (The same procedure is used to convert other
specification limits from time units to clock cycles.)
A subsequent ACTIVE command to a different row in the same bank can only be issued
after the previous active row has been precharged. The minimum time interval between
successive ACTIVE commands to the same bank is defined by tRC.
A subsequent ACTIVE command to another bank can be issued while the first bank is
being accessed, which results in a reduction of total row-access overhead. The minimum time interval between successive ACTIVE commands to different banks is defined
by tRRD.
Figure 16: Example: Meeting tRCD (MIN) When 2 < tRCD (MIN)/tCK < 3
T0
T1
T2
T3
CLK
tCK
Command
ACTIVE
tCK
NOP
tCK
NOP
READ or
WRITE
tRCD(MIN)
Don’t Care
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
45
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
READ Operation
READ Operation
READ bursts are initiated with a READ command, as shown in Figure 10 (page 30). The
starting column and bank addresses are provided with the READ command, and auto
precharge is either enabled or disabled for that burst access. If auto precharge is enabled, the row being accessed is precharged at the completion of the burst. In the following figures, auto precharge is disabled.
During READ bursts, the valid data-out element from the starting column address is
available following the CAS latency after the READ command. Each subsequent dataout element will be valid by the next positive clock edge. Figure 18 (page 48) shows
general timing for each possible CAS latency setting.
Upon completion of a burst, assuming no other commands have been initiated, the DQ
signals will go to High-Z. A continuous page burst continues until terminated. At the
end of the page, it wraps to column 0 and continues.
Data from any READ burst can be truncated with a subsequent READ command, and
data from a fixed-length READ burst can be followed immediately by data from a READ
command. In either case, a continuous flow of data can be maintained. The first data
element from the new burst either follows the last element of a completed burst or the
last desired data element of a longer burst that is being truncated. The new READ command should be issued x cycles before the clock edge at which the last desired data element is valid, where x = CL - 1. This is shown in Figure 18 (page 48) for CL2 and CL3.
SDRAM devices use a pipelined architecture and therefore do not require the 2n rule associated with a prefetch architecture. A READ command can be initiated on any clock
cycle following a READ command. Full-speed random read accesses can be performed
to the same bank, or each subsequent READ can be performed to a different bank.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
46
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
READ Operation
Figure 17: Consecutive READ Bursts
T0
T1
T2
T3
T4
T5
T6
CLK
Command
READ
NOP
NOP
NOP
READ
NOP
NOP
X = 1 cycle
Address
Bank,
Col n
Bank,
Col b
DOUT
n
DQ
DOUT
n+2
DOUT
n+1
DOUT
n+3
DOUT
b
CL = 2
T0
T1
T2
T3
T4
T5
T6
T7
CLK
Command
READ
NOP
NOP
NOP
READ
NOP
NOP
NOP
X = 2 cycles
Address
Bank,
Col n
Bank,
Col b
DOUT
DQ
CL = 3
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
DOUT
DOUT
Transitioning data
DOUT
DOUT
Don’t Care
1. Each READ command can be issued to any bank. DQM is LOW.
47
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
READ Operation
Figure 18: Random READ Accesses
T0
T1
T2
T3
T4
Command
READ
READ
READ
READ
Address
Bank,
Col n
Bank,
Col a
Bank,
Col x
Bank,
Col m
T5
CLK
DOUT
DQ
NOP
DOUT
NOP
DOUT
DOUT
CL = 2
T0
T1
T2
T3
T4
Command
READ
READ
READ
READ
Address
Bank,
Col n
Bank,
Col a
Bank,
Col x
Bank,
Col m
T5
T6
CLK
NOP
DOUT
DQ
DOUT
NOP
DOUT
NOP
DOUT
CL = 3
Transitioning data
Note:
Don’t Care
1. Each READ command can be issued to any bank. DQM is LOW.
Data from any READ burst can be truncated with a subsequent WRITE command, and
data from a fixed-length READ burst can be followed immediately by data from a
WRITE command (subject to bus turnaround limitations). The WRITE burst can be initiated on the clock edge immediately following the last (or last desired) data element
from the READ burst, provided that I/O contention can be avoided. In a given system
design, there is a possibility that the device driving the input data will go Low-Z before
the DQ go High-Z. In this case, at least a single-cycle delay should occur between the
last read data and the WRITE command.
The DQM input is used to avoid I/O contention, as shown in Figure 19 (page 49) and
Figure 20 (page 50). The DQM signal must be asserted (HIGH) at least two clocks prior
to the WRITE command (DQM latency is two clocks for output buffers) to suppress data-out from the READ. After the WRITE command is registered, the DQ will go to High-Z
(or remain High-Z), regardless of the state of the DQM signal, provided the DQM was
active on the clock just prior to the WRITE command that truncated the READ command. If not, the second WRITE will be an invalid WRITE. For example, if DQM was
LOW during T4, then the WRITEs at T5 and T7 would be valid, and the WRITE at T6
would be invalid.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
48
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
READ Operation
The DQM signal must be de-asserted prior to the WRITE command (DQM latency is
zero clocks for input buffers) to ensure that the written data is not masked. Figure 19
(page 49) shows where, due to the clock cycle frequency, bus contention is avoided
without having to add a NOP cycle, while Figure 20 (page 50) shows the case where an
additional NOP cycle is required.
A fixed-length READ burst may be followed by or truncated with a PRECHARGE command to the same bank, provided that auto precharge was not activated. The PRECHARGE command should be issued x cycles before the clock edge at which the last desired data element is valid, where x = CL - 1. This is shown in Figure 21 (page 50) for
each possible CL; data element n + 3 is either the last of a burst of four or the last desired data element of a longer burst. Following the PRECHARGE command, a subsequent command to the same bank cannot be issued until tRP is met. Note that part of
the row precharge time is hidden during the access of the last data element(s).
In the case of a fixed-length burst being executed to completion, a PRECHARGE command issued at the optimum time (as described above) provides the same operation
that would result from the same fixed-length burst with auto precharge. The disadvantage of the PRECHARGE command is that it requires that the command and address
buses be available at the appropriate time to issue the command. The advantage of the
PRECHARGE command is that it can be used to truncate fixed-length or continuous
page bursts.
Figure 19: READ-to-WRITE
T0
T1
T2
T3
T4
CLK
DQM
Command
READ
Address
Bank,
Col n
NOP
NOP
NOP
WRITE
Bank,
Col b
tCK
tHZ
DOUT
DQ
DIN
t
DS
Transitioning data
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
Don’t Care
1. CL = 3. The READ command can be issued to any bank, and the WRITE command can be
to any bank. If a burst of one is used, DQM is not required.
49
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
READ Operation
Figure 20: READ-to-WRITE With Extra Clock Cycle
T0
T1
T2
T3
T4
T5
CLK
DQM
Command
Address
READ
NOP
NOP
NOP
NOP
WRITE
Bank,
Col n
Bank,
Col b
tHZ
DOUT
DQ
DIN
tDS
Transitioning data
Note:
Don’t Care
1. CL = 3. The READ command can be issued to any bank, and the WRITE command can be
to any bank.
Figure 21: READ-to-PRECHARGE
T0
T1
T2
T3
T4
T5
T6
T7
CLK
tRP
Command
READ
Address
Bank a,
Col n
NOP
NOP
NOP
NOP
PRECHARGE
NOP
ACTIVE
X = 1 cycle
Bank
(a or all)
DOUT
DQ
DOUT
Bank a,
Row
DOUT
DOUT
CL = 2
T0
T1
T2
T3
T4
T5
T6
T7
CLK
t RP
Command
READ
NOP
NOP
NOP
PRECHARGE
NOP
NOP
ACTIVE
X = 2 cycles
Address
Bank
(a or all)
Bank a,
Col
DOUT
DQ
DOUT
Bank a,
Row
DOUT
DOUT
CL = 3
Transitioning data
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
Don’t Care
1. DQM is LOW.
50
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
READ Operation
Continuous-page READ bursts can be truncated with a BURST TERMINATE command
and fixed-length READ bursts can be truncated with a BURST TERMINATE command,
provided that auto precharge was not activated. The BURST TERMINATE command
should be issued x cycles before the clock edge at which the last desired data element is
valid, where x = CL - 1. This is shown in Figure 22 (page 51) for each possible CAS latency; data element n + 3 is the last desired data element of a longer burst.
Figure 22: Terminating a READ Burst
T0
T1
T2
T3
T4
T5
T6
CLK
Command
READ
Address
Bank,
Col n
NOP
NOP
NOP
BURST
TERMINATE
NOP
NOP
X = 1 cycle
DOUT
DQ
DOUT
DOUT
DOUT
CL = 2
T0
T1
T2
T3
T4
T5
T7
T6
CLK
Command
READ
Address
Bank,
Col n
NOP
NOP
NOP
BURST
TERMINATE
NOP
NOP
NOP
X = 2 cycles
DOUT
DQ
CL = 3
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
DOUT
DOUT
Transitioning data
DOUT
Don’t Care
1. DQM is LOW.
51
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
READ Operation
Figure 23: Alternating Bank Read Accesses
T0
tCK
CLK
T1
tCL
T2
T3
T4
T5
T6
T7
T8
READ
NOP
ACTIVE
tCH
tCKS
tCKH
tCMS
tCMH
CKE
Command
ACTIVE
NOP
READ
NOP
NOP
ACTIVE
tCMS tCMH
DQM
tAS
Address
Row
tAS
A10
tAH
1
Row
Column m
Row
Column b
Enable auto precharge
Enable auto precharge
Row
Row
tAS
BA0, BA1
tAH
Row
tAH
Bank 0
Bank 0
Bank 3
Bank 3
tAC
tAC
DQ
tLZ
tRCD - bank 0
tOH
tOH
tAC
DOUT
DOUT
Bank 0
tAC
tOH
DOUT
tAC
tOH
DOUT
tRP - bank 0
CL - bank 0
tAC
tOH
DOUT
tRCD - bank 0
tRAS - bank 0
tRC - bank 0
tRRD
tRCD - bank 3
CL - bank 3
Don’t Care
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
Undefined
1. For this example, BL = 4 and CL = 2.
52
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
READ Operation
Figure 24: READ Continuous Page Burst
T0
tCL
CLK
T1
tCH
tCK
T2
T3
T4
T5
T6
((
))
((
))
tCKS tCKH
tCMS
tCMH
ACTIVE
NOP
READ
tCMS
NOP
NOP
NOP
NOP
tCMH
tAS
A10
Tn + 4
((
))
((
))
NOP
BURST TERM
NOP
NOP
((
))
((
))
Column m
tAH
((
))
((
))
Row
tAS
BA0, BA1
tAH
Row
tAS
Tn + 3
((
))
((
))
DQM
Address
Tn + 2
((
))
((
))
CKE
Command
Tn + 1
tAH
Bank
((
))
((
))
Bank
tAC
tAC
tOH
DOUT
DQ
DOUT
tLZ
tRCD
CAS latency
tAC
tOH
tAC
tOH
((
))
((
DOUT ) )
((
))
tAC
tOH
DOUT
Full-page burst does not self-terminate.
Can use BURST TERMINATE command.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
DOUT
tOH
DOUT
tHZ
All locations within same row
Full page completed
Note:
tAC
tOH
Don’t Care
Undefined
1. For this example, CL = 2.
53
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
READ Operation
Figure 25: READ – DQM Operation
T0
tCK
CLK
tCKS
tCKH
tCMS
tCMH
T1
tCL
T2
T3
T4
T5
NOP
NOP
T6
T7
T8
NOP
NOP
tCH
CKE
Command
ACTIVE
NOP
READ
tCMS
NOP
NOP
tCMH
DQM
tAS
Row
Address
tAS
Column m
tAH
Enable auto precharge
Row
A10
tAS
BA0, BA1
tAH
Disable auto precharge
tAH
Bank
Bank
tAC
tOH
tAC
DQ
DOUT
tLZ
tRCD
tHZ
CL = 2
tAC
tLZ
tOH
tOH
DOUT
DOUT
tHZ
Don’t Care
Undefined
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1. For this example, BL = 4 and CL = 2.
54
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
WRITE Operation
WRITE Operation
WRITE bursts are initiated with a WRITE command, as shown in Figure 11 (page 31).
The starting column and bank addresses are provided with the WRITE command and
auto precharge is either enabled or disabled for that access. If auto precharge is enabled, the row being accessed is precharged at the completion of the burst. For the generic WRITE commands used in the following figures, auto precharge is disabled.
During WRITE bursts, the first valid data-in element is registered coincident with the
WRITE command. Subsequent data elements are registered on each successive positive
clock edge. Upon completion of a fixed-length burst, assuming no other commands
have been initiated, the DQ will remain at High-Z and any additional input data will be
ignored (see Figure 26 (page 55)). A continuous page burst continues until terminated;
at the end of the page, it wraps to column 0 and continues.
Data for any WRITE burst can be truncated with a subsequent WRITE command, and
data for a fixed-length WRITE burst can be followed immediately by data for a WRITE
command. The new WRITE command can be issued on any clock following the previous WRITE command, and the data provided coincident with the new command applies to the new command (see Figure 27 (page 56)). Data n + 1 is either the last of a
burst of two or the last desired data element of a longer burst.
SDRAM devices use a pipelined architecture and therefore do not require the 2n rule associated with a prefetch architecture. A WRITE command can be initiated on any clock
cycle following a previous WRITE command. Full-speed random write accesses within a
page can be performed to the same bank, as shown in Figure 28 (page 57), or each
subsequent WRITE can be performed to a different bank.
Figure 26: WRITE Burst
T0
T1
T2
T3
Command
WRITE
NOP
NOP
NOP
Address
Bank,
Col n
CLK
DQ
DIN
DIN
Transitioning data
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
Don’t Care
1. BL = 2. DQM is LOW.
55
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
WRITE Operation
Figure 27: WRITE-to-WRITE
T0
T1
T2
Command
WRITE
NOP
WRITE
Address
Bank,
Col n
CLK
DQ
DIN
Bank,
Col b
DIN
Transitioning data
Note:
DIN
Don’t Care
1. DQM is LOW. Each WRITE command may be issued to any bank.
Data for any WRITE burst can be truncated with a subsequent READ command, and
data for a fixed-length WRITE burst can be followed immediately by a READ command.
After the READ command is registered, data input is ignored and WRITEs will not be
executed (see Figure 29 (page 57)). Data n + 1 is either the last of a burst of two or the
last desired data element of a longer burst.
Data for a fixed-length WRITE burst can be followed by or truncated with a PRECHARGE command to the same bank, provided that auto precharge was not activated.
A continuous-page WRITE burst can be truncated with a PRECHARGE command to the
same bank. The PRECHARGE command should be issued tWR after the clock edge at
which the last desired input data element is registered. The auto precharge mode requires a tWR of at least one clock with time to complete, regardless of frequency.
In addition, when truncating a WRITE burst at high clock frequencies ( tCK < 15ns), the
DQM signal must be used to mask input data for the clock edge prior to and the clock
edge coincident with the PRECHARGE command (see Figure 30 (page 58)). Data n + 1
is either the last of a burst of two or the last desired data element of a longer burst. Following the PRECHARGE command, a subsequent command to the same bank cannot
be issued until tRP is met.
In the case of a fixed-length burst being executed to completion, a PRECHARGE command issued at the optimum time (as described above) provides the same operation
that would result from the same fixed-length burst with auto precharge. The disadvantage of the PRECHARGE command is that it requires that the command and address
buses be available at the appropriate time to issue the command. The advantage of the
PRECHARGE command is that it can be used to truncate fixed-length bursts or continuous page bursts.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
56
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
WRITE Operation
Figure 28: Random WRITE Cycles
T0
T1
T2
T3
Command
WRITE
WRITE
WRITE
WRITE
Address
Bank,
Col n
Bank,
Col a
Bank,
Col x
Bank,
Col m
DIN
DIN
DIN
DIN
CLK
DQ
Transitioning data
Note:
Don’t Care
1. Each WRITE command can be issued to any bank. DQM is LOW.
Figure 29: WRITE-to-READ
T0
T1
T2
Command
WRITE
NOP
READ
Address
Bank,
Col n
T3
T4
T5
NOP
NOP
NOP
DOUT
DOUT
CLK
DQ
DIN
Bank,
Col b
DIN
Transitioning data
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
Don’t Care
1. The WRITE command can be issued to any bank, and the READ command can be to any
bank. DQM is LOW. CL = 2 for illustration.
57
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
WRITE Operation
Figure 30: WRITE-to-PRECHARGE
T0
T1
T2
T3
T4
T5
T6
NOP
ACTIVE
NOP
CLK
tWR @ tCK ≥ 15ns
DQM
tRP
Command
Address
WRITE
NOP
NOP
PRECHARGE
Bank
(a or all)
Bank a,
Col n
Bank a,
Row
tWR
DQ
DIN
DIN
tWR @ tCK < 15ns
DQM
tRP
Command
Address
WRITE
NOP
NOP
PRECHARGE
NOP
NOP
Bank
(a or all)
Bank a,
Col n
ACTIVE
Bank a,
Row
t WR
DQ
DIN
DIN
Transitioning data
Note:
Don’t Care
1. In this example DQM could remain LOW if the WRITE burst is a fixed length of two.
Fixed-length WRITE bursts can be truncated with the BURST TERMINATE command.
When truncating a WRITE burst, the input data applied coincident with the BURST
TERMINATE command is ignored. The last data written (provided that DQM is LOW at
that time) will be the input data applied one clock previous to the BURST TERMINATE
command. This is shown in Figure 31 (page 59), where data n is the last desired data
element of a longer burst.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
58
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
WRITE Operation
Figure 31: Terminating a WRITE Burst
T0
T1
Command
WRITE
BURST
TERMINATE
Address
Bank,
Col n
T2
CLK
DQ
DIN
Transitioning data
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
NEXT
COMMAND
Address
Data
Don’t Care
1. DQM is LOW.
59
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
WRITE Operation
Figure 32: Alternating Bank Write Accesses
T0
tCK
CLK
T1
tCL
T2
T3
T4
T5
T6
T7
T8
T9
WRITE
NOP
NOP
ACTIVE
tCH
tCKS
tCKH
tCMS
tCMH
CKE
Command
ACTIVE
NOP
WRITE
tCMS
NOP
NOP
ACTIVE
tCMH
DQM
tAS
Address
tAS
A10
Row
Column m
tAH
Row
Column b
Enable auto precharge
Enable auto precharge
Row
tAS
BA0, BA1
tAH
Row
Row
Row
tAH
Bank 0
Bank 0
tDS
tDH
DIN
DQ
Bank 1
tDS
tDH
DIN
tDS
Bank 1
tDS
tDH
DIN
tDH
DIN
tDS
tDH
DIN
tWR - bank 0
tRCD - bank 0
Bank 0
tDS
tDH
DIN
tDS
tDH
DIN
tRP - bank 0
tDS
tDH
DIN
tRCD - bank 0
tRAS - bank 0
tWR - bank 1
tRC - bank 0
tRRD
tRCD - bank 1
Don’t Care
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1. For this example, BL = 4.
60
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
WRITE Operation
Figure 33: WRITE – Continuous Page Burst
T0
tCL
CLK
tCKS
T1
tCH
T2
tCK
T3
T4
T5
((
))
((
))
tCKH
Command
tCMH
ACTIVE
NOP
WRITE
NOP
NOP
NOP
tCMS tCMH
Address
A10
((
))
((
))
NOP
BURST TERM
NOP
((
))
((
))
Column m
tAH
((
))
((
))
Row
tAS
BA0, BA1
tAH
Row
tAS
Tn + 3
((
))
((
))
DQM
tAS
Tn + 2
((
))
((
))
CKE
tCMS
Tn + 1
tAH
Bank
((
))
((
))
Bank
tDS
DIN
DQ
tDH
tDS
tDH
tDS
DIN
tDH
DIN
tRCD
tDS
tDH
DIN
((
))
((
))
tDS
All locations within same row
tDH
DIN
Full-page burst
does not self-terminate.
Use BURST TERMINATE
command to stop.1, 2
Full page completed
Notes:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
Don’t Care
1. tWR must be satisfied prior to issuing a PRECHARGE command.
2. Page left open; no tRP.
61
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
WRITE Operation
Figure 34: WRITE – DQM Operation
T0
tCK
CLK
tCKS
tCKH
tCMS
tCMH
T1
tCL
T2
T3
T4
T5
NOP
NOP
NOP
T6
T7
NOP
NOP
tCH
CKE
Command
ACTIVE
NOP
WRITE
tCMS tCMH
DQM
tAS
Address
Row
tAS
A10
Column m
tAH
Enable auto precharge
Row
tAS
BA0, BA1
tAH
Disable auto precharge
tAH
Bank
Bank
tDS
tDH
tDS
DIN
DQ
DIN
tRCD
Note:
tDH
tDS
tDH
DIN
Don’t Care
1. For this example, BL = 4.
Burst Read/Single Write
The burst read/single write mode is entered by programming the write burst mode bit
(M9) in the mode register to a 1. In this mode, all WRITE commands result in the access
of a single column location (burst of one), regardless of the programmed burst length.
READ commands access columns according to the programmed burst length and sequence, just as in the normal mode of operation (M9 = 0).
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
62
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
PRECHARGE Operation
PRECHARGE Operation
The PRECHARGE command (see Figure 12 (page 32)) is used to deactivate the open row
in a particular bank or the open row in all banks. The bank(s) will be available for a subsequent row access some specified time (tRP) after the PRECHARGE command is issued. Input A10 determines whether one or all banks are to be precharged, and in the
case where only one bank is to be precharged (A10 = LOW), inputs BA0 and BA1 select
the bank. When all banks are to be precharged (A10 = HIGH), inputs BA0 and BA1 are
treated as “Don’t Care.” After a bank has been precharged, it is in the idle state and
must be activated prior to any READ or WRITE commands being issued to that bank.
Auto Precharge
Auto precharge is a feature that performs the same individual-bank PRECHARGE function described previously, without requiring an explicit command. This is accomplished
by using A10 to enable auto precharge in conjunction with a specific READ or WRITE
command. A precharge of the bank/row that is addressed with the READ or WRITE
command is automatically performed upon completion of the READ or WRITE burst,
except in the continuous page burst mode where auto precharge does not apply. In the
specific case of write burst mode set to single location access with burst length set to
continuous, the burst length setting is the overriding setting and auto precharge does
not apply. Auto precharge is nonpersistent in that it is either enabled or disabled for
each individual READ or WRITE command.
Auto precharge ensures that the precharge is initiated at the earliest valid stage within a
burst. Another command cannot be issued to the same bank until the precharge time
(tRP) is completed. This is determined as if an explicit PRECHARGE command was issued at the earliest possible time, as described for each burst type in the (page 0 ) section.
Micron SDRAM supports concurrent auto precharge; cases of concurrent auto precharge for READs and WRITEs are defined below.
READ with auto precharge interrupted by a READ (with or without auto precharge)
A READ to bank m will interrupt a READ on bank n following the programmed CAS latency. The precharge to bank n begins when the READ to bank m is registered (see Figure 35 (page 64)).
READ with auto precharge interrupted by a WRITE (with or without auto precharge)
A WRITE to bank m will interrupt a READ on bank n when registered. DQM should be
used two clocks prior to the WRITE command to prevent bus contention. The precharge to bank n begins when the WRITE to bank m is registered (see Figure 36
(page 65)).
WRITE with auto precharge interrupted by a READ (with or without auto precharge)
A READ to bank m will interrupt a WRITE on bank n when registered, with the data-out
appearing CL later. The precharge to bank n will begin after tWR is met, where tWR begins when the READ to bank m is registered. The last valid WRITE to bank n will be data-in registered one clock prior to the READ to bank m (see Figure 41 (page 70)).
WRITE with auto precharge interrupted by a WRITE (with or without auto precharge)
A WRITE to bank m will interrupt a WRITE on bank n when registered. The precharge to
bank n will begin after tWR is met, where tWR begins when the WRITE to bank m is reg-
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
63
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
PRECHARGE Operation
istered. The last valid data WRITE to bank n will be data registered one clock prior to a
WRITE to bank m (see Figure 42 (page 70)).
Figure 35: READ With Auto Precharge Interrupted by a READ
T0
T1
T2
T3
T4
T5
T6
T7
CLK
Command
Bank n
Internal
states
NOP
Page active
READ - AP
Bank n
READ - AP
Bank m
NOP
READ with burst of 4
NOP
NOP
NOP
Interrupt burst, precharge
Idle
tRP - bank n
Bank m
Page active
Address
Bank n,
Col a
NOP
tRP - bank m
Precharge
READ with burst of 4
Bank m,
Col d
DOUT
DQ
DOUT
DOUT
DOUT
CL = 3 (bank n)
CL = 3 (bank m)
Don’t Care
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1. DQM is LOW.
64
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
PRECHARGE Operation
Figure 36: READ With Auto Precharge Interrupted by a WRITE
T0
T1
T2
T3
T4
T5
T6
T7
CLK
Command
Internal
States
Bank n
READ - AP
Bank n
Page
active
NOP
NOP
NOP
READ with burst of 4
WRITE - AP
Bank m
NOP
NOP
Interrupt burst, precharge
Idle
tWR - bankm
tRP - bank n
Page active
Bank m
Address
NOP
Write-back
WRITE with burst of 4
Bank n,
Col a
Bank m,
Col d
DQM1
DOUT
DQ
CL = 3 (bank n)
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
DIN
DIN
DIN
Transitioning data
DIN
Don’t Care
1. DQM is HIGH at T2 to prevent DOUTa + 1 from contending with DINd at T4.
65
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
PRECHARGE Operation
Figure 37: READ With Auto Precharge
T0
tCK
CLK
tCKS
tCKH
tCMS
tCMH
T1
tCL
T2
T3
T4
T5
NOP
NOP
T6
T7
T8
NOP
NOP
ACTIVE
tCH
CKE
Command
ACTIVE
NOP
READ
tCMS
NOP
tCMH
DQM
tAS
Address
Row
tAS
A10
Row
Column m
tAH
Enable auto precharge
Row
tAS
BA0, BA1
tAH
Row
tAH
Bank
Bank
Bank
tAC
tOH
tAC
DQ
tLZ
tRCD
DOUT m
tAC
tOH
DOUT
m+1
tAC
tOH
DOUT
m+2
tRP
CL = 2
tOH
DOUT
m+3
tHZ
tRAS
tRC
Don’t Care
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
Undefined
1. For this example, BL = 4 and CL = 2.
66
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
PRECHARGE Operation
Figure 38: READ Without Auto Precharge
T0
tCK
CLK
tCKS
T1
tCL
T2
T3
T4
T5
NOP
NOP
T6
T7
T8
NOP
ACTIVE
tCH
tCKH
CKE
tCMS tCMH
Command
ACTIVE
NOP
READ
NOP
PRECHARGE
tCMS tCMH
DQM
tAS
Address
Row
tAS
Row
Column m
tAH
All banks
Row
A10
tAS
BA0, BA1
tAH
Row
tAH
Bank
Disable auto precharge
Single bank
Bank
Bank(s)
tAC
tOH
tAC
DQ
tLZ
tRCD
DOUT
tOH
DOUT
Bank
tAC
tAC
tOH
DOUT
tRP
CL = 2
tOH
DOUT
tHZ
tRAS
tRC
Don’t Care
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
Undefined
1. For this example, BL = 4, CL = 2, and the READ burst is followed by a manual PRECHARGE.
67
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
PRECHARGE Operation
Figure 39: Single READ With Auto Precharge
T0
tCK
CLK
tCKS
tCKH
tCMS
tCMH
T1
tCL
T2
T3
T4
T5
NOP
NOP
T6
T7
tCH
CKE
Command
ACTIVE
NOP
READ
NOP
NOP
ACTIVE
tCMS tCMH
DQM
tAS
Address
Row
Column m
Row
tAS
tAH
Enable auto precharge
Row
Row
A10
tAS
BA0, BA1
tAH
tAH
Bank
Bank
Bank
tAC
DQ
DOUT
tLZ
tRCD
tRAS
tOH
tRP
CL = 2
tRC
Don’t Care
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
Undefined
1. For this example, BL = 1 and CL = 2.
68
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
PRECHARGE Operation
Figure 40: Single READ Without Auto Precharge
T0
tCK
CLK
tCKS
tCKH
tCMS
tCMH
T1
tCL
T2
T3
T4
T5
NOP
NOP
T6
T7
T8
tCH
CKE
Command
ACTIVE
NOP
READ
PRECHARGE
NOP
ACTIVE
NOP
tCMS tCMH
DQM
tAS
Address
A10
Row
Column m
Row
tAS
tAH
All banks
Row
Row
tAS
BA0, BA1
tAH
tAH
Single bank
Disable auto precharge
Bank
Bank(s)
Bank
DQ
tLZ
tRCD
DOUT
tHZ
CL = 2
tRP
Don’t Care
tRAS
tRC
Undefined
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
Bank
tOH
tAC
1. For this example, BL = 1, CL = 2, and the READ burst is followed by a manual PRECHARGE.
69
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
PRECHARGE Operation
Figure 41: WRITE With Auto Precharge Interrupted by a READ
T0
T1
T2
T3
T4
T5
T6
T7
CLK
Command
Internal
States
Bank n
NOP
Page active
WRITE - AP
Bank n
READ - AP
Bank m
NOP
NOP
NOP
Interrupt burst, write-back
WRITE with burst of 4
Page active
Address
Bank n,
Col a
DIN
DQ
NOP
Precharge
tRP - bank n
t WR - bank n
Bank m
NOP
tRP - bank m
READ with burst of 4
Bank m,
Col d
DIN
DOUT
DOUT
CL = 3 (bank m)
Don’t Care
Note:
1. DQM is LOW.
Figure 42: WRITE With Auto Precharge Interrupted by a WRITE
T0
T1
T2
T3
T4
T5
T7
T6
CLK
Command
Bank n
Internal
States
NOP
Page active
WRITE - AP
Bank n
NOP
NOP
WRITE with burst of 4
WRITE - AP
Bank m
NOP
Interrupt burst, write-back
Address
DQ
Page active
tWR - bank m
Write-back
WRITE with burst of 4
Bank n,
Col a
DIN
Precharge
tRP - bank n
tWR - bank n
Bank m
NOP
NOP
Bank m,
Col d
DIN
DIN
DIN
DIN
DIN
DIN
Don’t Care
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1. DQM is LOW.
70
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
PRECHARGE Operation
Figure 43: WRITE With Auto Precharge
T0
tCK
CLK
T1
tCL
T2
T3
T4
T5
T6
T7
T8
T9
NOP
NOP
NOP
NOP
NOP
NOP
ACTIVE
tCH
tCKS
tCKH
tCMS
tCMH
CKE
Command
ACTIVE
NOP
WRITE
tCMS tCMH
DQM
tAS
Address
Row
tAS
A10
Row
Column m
tAH
Enable auto precharge
Row
Row
tAS
BA0, BA1
tAH
tAH
Bank
Bank
Bank
tDS
tDH
DIN
DQ
tDS
tDH
DIN
tDS
tDH
DIN
tDS
tDH
DIN
tRCD
tRAS
tWR
tRP
tRC
Don’t Care
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1. For this example, BL = 4.
71
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
PRECHARGE Operation
Figure 44: WRITE Without Auto Precharge
T0
tCK
CLK
T1
tCL
T2
T3
T4
T5
T6
NOP
NOP
NOP
NOP
T7
T8
T9
PRECHARGE
NOP
ACTIVE
tCH
tCKS
tCKH
tCMS
tCMH
CKE
Command
ACTIVE
NOP
WRITE
tCMS tCMH
DQM
tAS
Address
Row
tAS
A10
Column m
Row
tAH
All banks
Row
Row
tAS
BA0, BA1
tAH
tAH
Bank
Disable auto precharge
Single bank
Bank
Bank
tDS
tDH
DIN
DQ
tDS
tDH
DIN
tDS
tDH
DIN
tDS
Bank
tDH
DIN
tRCD
tRAS
tWR
tRP
tRC
Don’t Care
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1. For this example, BL = 4 and the WRITE burst is followed by a manual PRECHARGE.
72
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
PRECHARGE Operation
Figure 45: Single WRITE With Auto Precharge
T0
tCK
CLK
T1
T2
tCL
T3
T4
T5
T6
NOP
NOP
NOP
NOP
T7
T8
ACTIVE
NOP
tCH
tCKS
tCKH
tCMS
tCMH
CKE
Command
ACTIVE
NOP
WRITE
tCMS tCMH
DQM
tAS
Address
Row
tAS
A10
Row
Column m
tAH
Enable auto precharge
Row
Row
tAS
BA0, BA1
tAH
tAH
Bank
Bank
Bank
tDS
tDH
DIN
DQ
tRCD
tRAS
tRP
tWR
tRC
Don’t Care
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1. For this example, BL = 1.
73
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
PRECHARGE Operation
Figure 46: Single WRITE Without Auto Precharge
T0
tCK
CLK
tCKS
tCKH
tCMS
tCMH
T1
tCL
T2
T3
T4
NOP
NOP
T5
T6
T7
T8
tCH
CKE
Command
ACTIVE
NOP
WRITE
PRECHARGE
NOP
ACTIVE
NOP
tCMS tCMH
DQM
tAS
Row
Address
tAS
A10
Column m
tAH
All banks
Row
Row
tAS
BA0, BA1
tAH
tAH
Bank
Disable auto precharge
Single bank
Bank
Bank
tDS
Bank
tDH
DIN
DQ
tRCD
tRP
tWR
tRAS
tRC
Don’t Care
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1. For this example, BL = 1 and the WRITE burst is followed by a manual PRECHARGE.
74
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
AUTO REFRESH Operation
AUTO REFRESH Operation
The AUTO REFRESH command is used during normal operation of the device to refresh
the contents of the array. This command is nonpersistent, so it must be issued each
time a refresh is required. All active banks must be precharged prior to issuing an AUTO
REFRESH command. The AUTO REFRESH command should not be issued until the
minimum tRP is met following the PRECHARGE command. Addressing is generated by
the internal refresh controller. This makes the address bits “Don’t Care” during an AUTO REFRESH command.
After the AUTO REFRESH command is initiated, it must not be interrupted by any executable command until tRFC has been met. During tRFC time, COMMAND INHIBIT or
NOP commands must be issued on each positive edge of the clock. The SDRAM requires that every row be refreshed each tREF period. Providing a distributed AUTO REFRESH command—calculated by dividing the refresh period (tREF) by the number of
rows to be refreshed—meets the timing requirement and ensures that each row is refreshed. Alternatively, to satisfy the refresh requirement a burst refresh can be employed
after every tREF period by issuing consecutive AUTO REFRESH commands for the number of rows to be refreshed at the minimum cycle rate (tRFC).
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
75
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
AUTO REFRESH Operation
Figure 47: Auto Refresh Mode
T0
T1
CLK
tCK
T2
((
))
((
))
tCH
tCKS
tCKH
tCMS
tCMH
PRECHARGE
NOP
AUTO
REFRESH
NOP
((
))
( ( NOP
))
Address
All banks
A10
Single bank
tAS
To + 1
((
))
AUTO
REFRESH
NOP
((
))
((
))
DQM
BA0, BA1
((
))
((
))
((
))
CKE
Command
Tn + 1
tCL
((
))
( ( NOP
))
ACTIVE
((
))
((
))
((
))
((
))
((
))
((
))
Row
((
))
((
))
((
))
((
))
Row
((
))
((
))
((
))
((
))
Bank
((
))
((
))
tAH
Bank(s)
DQ High-Z
tRP
tRFC
tRFC
Precharge all
active banks
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
Don’t Care
1. Back-to-back AUTO REFRESH commands are not required.
76
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
SELF REFRESH Operation
SELF REFRESH Operation
The self refresh mode can be used to retain data in the device, even when the rest of the
system is powered down. When in self refresh mode, the device retains data without external clocking. The SELF REFRESH command is initiated like an AUTO REFRESH command, except CKE is disabled (LOW). After the SELF REFRESH command is registered,
all the inputs to the device become “Don’t Care” with the exception of CKE, which must
remain LOW.
After self refresh mode is engaged, the device provides its own internal clocking, enabling it to perform its own AUTO REFRESH cycles. The device must remain in self refresh mode for a minimum period equal to tRAS and remains in self refresh mode for an
indefinite period beyond that.
The procedure for exiting self refresh requires a sequence of commands. First, CLK
must be stable prior to CKE going back HIGH. (Stable clock is defined as a signal cycling
within timing constraints specified for the clock ball.) After CKE is HIGH, the device
must have NOP commands issued for a minimum of two clocks for tXSR because time is
required for the completion of any internal refresh in progress.
Upon exiting the self refresh mode, AUTO REFRESH commands must be issued according to the distributed refresh rate (tREF/refresh row count) as both SELF REFRESH and
AUTO REFRESH utilize the row refresh counter.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
77
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
SELF REFRESH Operation
Figure 48: Self Refresh Mode
T0
T1
CLK
tCK
tCL
tCH
T2
tCKS
CKE
Command
tCKS
tCKH
tCMS
tCMH
PRECHARGE
((
))
((
))
((
))
NOP
AUTO
REFRESH
((
))
((
))
Tn + 1
((
))
((
))
((
))
))
((
))
((
))
Address
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
Single bank
tAS
BA0, BA1
DQ
tAH
Bank(s)
High-Z
tRP
Precharge all
active banks
Enter self refresh mode
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
tXSR
Exit self refresh mode
(Restart refresh time base)
CLK stable prior to exiting
self refresh mode
Note:
AUTO
REFRESH
NOP ( (
((
))
((
))
All banks
To + 2
((
))
((
))
DQM
A10
To + 1
Don’t Care
1. Each AUTO REFRESH command performs a REFRESH cycle. Back-to-back commands are
not required.
78
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Power-Down
Power-Down
Power-down occurs if CKE is registered LOW coincident with a NOP or COMMAND INHIBIT when no accesses are in progress. If power-down occurs when all banks are idle,
this mode is referred to as precharge power-down; if power-down occurs when there is a
row active in any bank, this mode is referred to as active power-down. Entering powerdown deactivates the input and output buffers, excluding CKE, for maximum power
savings while in standby. The device cannot remain in the power-down state longer
than the refresh period (64ms) because no REFRESH operations are performed in this
mode.
The power-down state is exited by registering a NOP or COMMAND INHIBIT with CKE
HIGH at the desired clock edge (meeting tCKS).
Figure 49: Power-Down Mode
T0
tCK
CLK
T1
tCL
T2
tCKS
((
))
((
))
tCH
CKE
tCKS
Tn + 2
tCKS
((
))
tCKH
tCMS tCMH
Command
Tn + 1
NOP
PRECHARGE
((
))
((
))
NOP
NOP
ACTIVE
DQM
((
))
((
))
Address
((
))
((
))
Row
((
))
((
))
Row
((
))
((
))
Bank
All banks
A10
Single bank
tAS
BA0, BA1
DQ
tAH
Bank(s)
High-Z
((
))
Two clock cycles
Input buffers gated off
All banks idle
while in power-down mode
Precharge all
active banks
All banks idle, enter
power-down mode
Exit power-down mode
Don’t Care
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1. Violating refresh requirements during power-down may result in a loss of data.
79
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Clock Suspend
Clock Suspend
The clock suspend mode occurs when a column access/burst is in progress and CKE is
registered LOW. In the clock suspend mode, the internal clock is deactivated, freezing
the synchronous logic.
For each positive clock edge on which CKE is sampled LOW, the next internal positive
clock edge is suspended. Any command or data present on the input balls when an internal clock edge is suspended will be ignored; any data present on the DQ balls remains driven; and burst counters are not incremented, as long as the clock is suspended.
Exit clock suspend mode by registering CKE HIGH; the internal clock and related operation will resume on the subsequent positive clock edge.
Figure 50: Clock Suspend During WRITE Burst
T0
T1
NOP
WRITE
T2
T3
T4
T5
NOP
NOP
DIN
DIN
CLK
CKE
Internal
clock
Command
Address
DIN
Bank,
Col n
DIN
Don’t Care
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1. For this example, BL = 4 or greater, and DQM is LOW.
80
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Clock Suspend
Figure 51: Clock Suspend During READ Burst
T0
T1
T2
T3
T4
T5
T6
CLK
CKE
Internal
clock
Command
READ
Address
Bank,
Col n
DQ
NOP
NOP
NOP
DOUT
DOUT
NOP
DOUT
NOP
DOUT
Don’t Care
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
1. For this example, CL = 2, BL = 4 or greater, and DQM is LOW.
81
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Clock Suspend
Figure 52: Clock Suspend Mode
T0
tCK
CLK
T1
tCL
tCKS
T2
T3
T4
T5
T6
T7
T8
T9
tCH
tCKH
CKE
tCKS tCKH
tCMS
Command
tCMH
READ
NOP
NOP
NOP
NOP
NOP
NOP
WRITE
tCMS tCMH
DQM
tAS
Address
tAH
Column e
Column m
tAS
tAH
tAS
tAH
A10
BA0, BA1
Bank
Bank
tAC
tOH
tAC
DQ
tLZ
tHZ
DOUT
DOUT
tDS
tDH
DIN
DIN
Don’t Care
Note:
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
Undefined
1. For this example, BL = 2, CL = 3, and auto precharge is disabled.
82
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
64Mb: x8, x16 SDRAM
Revision History
Revision History
Rev. C – 11/13
• Changed to Production status
Rev. B – 3/12
• Removed confidential/proprietary header
Rev. A – 12/11
• Initial release
Created from PDF: 09005aef80725c0b 64MSDRAM_1.fm - Rev. P 11/11 EN
8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900
www.micron.com/productsupport Customer Comment Line: 800-932-4992
Micron and the Micron logo are trademarks of Micron Technology, Inc.
All other trademarks are the property of their respective owners.
This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein.
Although considered final, these specifications are subject to change, as further product development and data characterization sometimes occur.
PDF: 09005aef84942e37
64mb_ait_aat_sdr.pdf - Rev. C 11/13 EN
83
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.