Switch mode Power Supply S82J Compact and Economical Switch mode Power Supplies with Capacities Up to 600 W DIN Track Mounting Bracket Type Now Available • Power range from 10 W up to 600 W. • Output Voltages: 5 V, 12 V, 15 V, or 24 V. • Mounting bracket provided for mounting to control panels. • Maintenance-free up to 300 W due to natural ventilation. • Protection-ON alarm indicator shows valuable protection functions in action (300-/600-W models). • Conforms to EMC standards: EN50081-2 and EN50082-2. • With an external filter, achieves conformance to EN50081-1 for universal usage on EMI (300-/600-W models). • Finger protection terminal block to meet VDE0106/P100 • Class 2 approved 10-W, 25-W (except for 5-V output), and 50-W (only for 24-V output) models. • UL508 approved. All models can be used at full load in UL508A industrial control panel applications. • Approved by UL/CSA standards, EN60950, and EN50178 (VDE0160). • Six-language instruction manual provided. (English, French, German, Italian, Spanish, and Japanese) S82J Covered Type Open-frame Type <10 W to 150 W> • 100 to 240-VAC input • 100 or 200 VAC (selected automatically) (100-W 5-/12-/15-V output, 150-W models) <10 W to 150 W> • 100 to 240-VAC input • 100 or 200 VAC (selected automatically) (100-W 5-/12-/15-V output, 150-W models) Enclosure Type <300/600 W> • 100 or 200 VAC (selectable) Model Number Structure ■ Model Number Legend S82J 2 3 4 1. Power Ratings 010: 10 W 025: 25 W 050: 50 W 100: 100 W 150: 150 W 300: 300 W 600: 600 W 4. Mounting Bracket None: Front-mounting Bracket Type D: DIN Track Mounting Bracket Type 2. Output Voltage 05: 5V 12: 12 V 15: 15 V 24: 24 V 3. Configuration A: Open-frame type, front terminals B: Open-frame type, top terminals C: Open-frame type, connector D: Covered type, front terminals E: Covered type, top terminals F: Covered type, connector N: Without Mounting Bracket None: Enclosure type, front terminals with Mounting Bracket Switch mode Power Supply S82J Power Supplies 1 L-79 Ordering Information ■ Front-mounting Bracket Type Configuration Input Voltage Power ratings Open-frame type 100 to 240 VAC 10 W Front terminals Top terminals Connector 2A S82J-01005A --- --- 12 V 1A S82J-01012A --- --- 15 V 0.7 A S82J-01015A --- --- 24 V 0.5 A S82J-01024A --- --- 5V 5A S82J-02505A --- --- 12 V 2.1 A S82J-02512A --- --- 15 V 1.7 A S82J-02515A --- --- 24 V 1.1 A S82J-02524A --- --- 5V 10 A S82J-05005A --- --- 12 V 4.2 A S82J-05012A --- --- 24 V 2.1 A S82J-05024A --- --- 100 or 200 VAC 100 W (selected automatically) 5V 20 A S82J-10005A S82J-10005B S82J-10005C 12 V 8.5 A S82J-10012A S82J-10012B S82J-10012C 15 V 7A S82J-10015A S82J-10015B S82J-10015C 100 to 240 VAC 24 V 4.5 A S82J-10024A --- --- 100 or 200 VAC 150 W (selected automatically) 24 V 6.5 A S82J-15024A S82J-15024B S82J-15024C 100 to 240 VAC 10 W 5V 2A S82J-01005D --- --- 12 V 1A S82J-01012D --- --- 15 V 0.7 A S82J-01015D --- --- 24 V 0.5 A S82J-01024D --- --- 5V 5A S82J-02505D --- --- 12 V 2.1 A S82J-02512D --- --- 15 V 1.7 A S82J-02515D --- --- 24 V 1.1 A S82J-02524D --- --- 5V 10 A S82J-05005D --- --- 12 V 4.2 A S82J-05012D --- --- 24 V 2.1 A S82J-05024D --- --- 100 or 200 VAC 100 W (selected automatically) 5V 20 A S82J-10005D S82J-10005E S82J-10005F 12 V 8.5 A S82J-10012D S82J-10012E S82J-10012F 15 V 7A S82J-10015D S82J-10015E S82J-10015F 100 to 240 VAC 24 V 4.5 A S82J-10024D --- --- 100 or 200 VAC 150 W (selected automatically) 24 V 6.5 A S82J-15024D S82J-15024E S82J-15024F 100 or 200 VAC 300 W (selectable) 24 V 14 A S82J-30024 --- --- S82J-30024N --- --- S82J-60024 --- --- S82J-60024N --- --- 50 W 25 W 50 W 600 W L-80 Output current 5V 25 W Covered type Output voltage Switch mode Power Supply S82J 27 A ■ DIN Track Mounting Bracket Type Input Voltage Power ratings Open-frame type 100 to 240 VAC 10 W Output current Front terminals Top terminals Connector 5V 2A S82J-01005AD --- --- 12 V 1A S82J-01012AD --- --- 15 V 0.7 A S82J-01015AD --- --- 24 V 0.5 A S82J-01024AD --- --- 5V 5A S82J-02505AD --- --- 12 V 2.1 A S82J-02512AD --- --- 15 V 1.7 A S82J-02515AD --- --- 24 V 1.1 A S82J-02524AD --- --- 5V 10 A S82J-05005AD --- --- 12 V 4.2 A S82J-05012AD --- --- 24 V 2.1 A S82J-05024AD --- --- 100 or 200 VAC 100 W (selected automatically) 5V 20 A S82J-10005AD S82J-10005BD S82J-10005CD 12 V 8.5 A S82J-10012AD S82J-10012BD S82J-10012CD 15 V 7A S82J-10015AD S82J-10015BD S82J-10015CD 100 to 240 VAC 24 V 4.5 A S82J-10024AD --- --- 100 or 200 VAC 150 W (selected automatically) 24 V 6.5 A S82J-15024AD S82J-15024BD S82J-15024CD 100 to 240 VAC 10 W 5V 2A S82J-01005DD --- --- 12 V 1A S82J-01012DD --- --- 15 V 0.7 A S82J-01015DD --- --- 25 W 50 W Covered type Output voltage 24 V 0.5 A S82J-01024DD --- --- 5V 5A S82J-02505DD --- --- 12 V 2.1 A S82J-02512DD --- --- 15 V 1.7 A S82J-02515DD --- --- 24 V 1.1 A S82J-02524DD --- --- 5V 10 A S82J-05005DD --- --- 12 V 4.2 A S82J-05012DD --- --- 24 V 2.1 A S82J-05024DD --- --- 100 or 200 VAC 100 W (selected automatically) 5V 20 A S82J-10005DD S82J-10005ED S82J-10005FD 12 V 8.5 A S82J-10012DD S82J-10012ED S82J-10012FD 15 V 7A S82J-10015DD S82J-10015ED S82J-10015FD 100 to 240 VAC 24 V 4.5 A S82J-10024DD --- --- 100 or 200 VAC 150 W (selected automatically) 24 V 6.5 A S82J-15024DD S82J-15024ED S82J-15024FD 25 W 50 W Power Supplies Configuration Switch mode Power Supply S82J L-81 L-82 Switch mode Power Supply S82J Specifications ■ Ratings/Characteristics Item 100 to 240 VAC input 10 W 25 W 50 W 100 or 200 VAC (selected automatically) 100 W (24 V) 100 W (5, 12, 15 V) 150 W Efficiency (typical) 67% min. (77% min. for 50-W, 24- 83% min. V models) 75% min. Input 100 to 240 VAC (85 to 264 VAC) 110 to 170 VDC (set the terminal (L) to + side) (10 and 25 W only) (See note 1.) 100 (85 to 132) or 200 (170 to 264) VAC (selected automatically) Voltage 300 W 600 W 82% min. 100 (85 to 132) or 200 (170 to 253) VAC (selectable) 50/60 Hz (47 to 450 Hz) Frequency Output (See note 3.) 100 or 200 VAC (selectable) Current (See note 2.) 100 VAC input 0.35 A max. 0.8 A max. 1.4 A max. 2.5 A max. 2.5 A max. 3.5 A max. 8 A max. 14 A max. 200 VAC input 0.3 A max. 0.6 A max. 0.8 A max. 1.5 A max. 1.4 A max. 2.1 A max. 4 A max. 7 A max. Leakage current (See note 2.) 100 VAC input 0.5 mA max. 200 VAC input 1 mA max. Inrush current (25°C, cold start) (See note 2.) 100 VAC input 25 A max. 30 A max. 200 VAC input 50 A max. 60 A max. Noise filter Yes Voltage adjustment range ±10% (adjustable with variable resistor (V. ADJ)) Ripple (See note 2.) 2% (p-p) max. Input variation influence 0.4% max. Load variation influence 0.8% max. (with rated input, 10% to 100% load) Temperature variation influence 0.05%/°C max. (with rated input and output) Startup time 500 ms max. (up to 90% of output voltage at rated input and output) 300 ms max. (up to 90% of output voltage at rated input and output) Hold time (See note 2.) 20 ms min. Overload protection 105% to 160% of rated load current, inverted L drop/intermittent operation type, automatic reset No Overvoltage protection (See note 5.) Overheat protection No Protection-ON alarm indicator No Parallel operation No Series operation No Yes (See note 5.) 105% min. of rated load current, inverted L drop type, automatic reset (For the 600-W model, the circuit will be shut OFF when the overload exceeds 5 ±3 s. Protection-ON alarm indicator lit (See note 4.)) Yes (5-V out- No put models only) (See note 5.) Yes, protection-ON alarm indicator lit (See note 4.) Yes, protectionON alarm indicator lit (See note 4.) Yes (color, red) Yes, 5 units max. Yes Power Supplies Additional function Switching Power Supply S82J L-83 Item 100 to 240 VAC input 10 W Other 25 W 50 W 100 or 200 VAC (selected automatically) 100 W (24 V) 100 W (5, 12, 15 V) Ambient temperature Operating: See the derating curve in the Engineering Data section. −25 to 65°C (with no condensation and icing) Storage: Ambient humidity Operating: 25% to 85% Storage: 25% to 90% Dielectric strength 3.0 kVAC, 50/60 Hz for 1 min (between all inputs and all outputs) 150 W 100 or 200 VAC (selectable) 300 W 600 W 2.2 kVAC, 50/60 Hz for 1 min (between all inputs and GR terminal) 1.0 kVAC, 50/60 Hz for 1 min (between all outputs and GR terminal) Insulation resistance 100 MΩ min. (between all outputs and all inputs/GR terminals at 500 VDC) Vibration resistance 10 to 55 Hz, 0.375-mm double amplitude for 2 h each in X, Y, and Z directions Shock resistance 300 m/s2, 3 times each in ±X, ±Y, and ±Z directions Terminal screw tightening 0.74 N·m Output indicator Yes (green) Electromagnetic interference (See note 2.) Conforms to FCC Class A EMC Emission Enclosure: Emission AC Mains: Immunity ESD: EMC standards Conforms to EN50081-2 and EN50082-2 Approved standards UL UL508 (Listing), 1950, Class 2 (per UL1310) (See note 10.) UL508 (Listing), 1012, 1950 (See note 8.) UL508/1012 CSA CSA C22.2 No. 14, No. 950, Class 2 (See note 10.) CSA C22.2 No. 14, No. 950 VDE EN50178 (VDE0160) and EN60950 Terminal types (only terminal part): VDE0106/P100 EN55011 class A EN55011 class A EN61000-4-2: 4 kV contact discharge (level 2) 8 kV air discharge (level 3) Immunity RF-interference: ENV50140: 10 Vm (80 MHz to 1 GHz) (level 3) Immunity Conducted Disturbance: ENV50141: 10 V (0.5 to 80 MHz) (level 3) Immunity Burst: EN61000-4-4: 2 kV power-line (level 3) 2 kV output line (level 4) 250 g max. Weight (See note 9.) Note: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 1.08 N·m 350 g max. 400 g max. 500 g max. Conforms to EN50081-2 and EN50082-2 (See note 6.) With noise filter, confirms to EN50081-1 (See note 6 and 7.) 1,000 g max. CSA EB1402C 2,000 g max. 2,500 g max. DC inputs not included in safety standard approvals. At 100% load for rated input voltage (100 VAC or 200 VAC). The output specification is defined at the power supply output terminals. For resetting, turn OFF the power supply, leave for more than three minutes (90 seconds min. for the 300-W models), and then turn ON the power supply. For resetting, turn OFF the power supply, leave for more than one minute, and then turn ON the power supply. To ensure the Emission Enclosure rating ferrite ring cores (recommended model: S82Y-JC-T) should be used on all cabling. To ensure the Emission AC Mains rating for EN50081-1 (only for 200-VAC input), a noise filter (recommended models: S82Y-JF3-N for 300-W, S82Y-JF6-N for 600-W) should be used on the input lines. With UL508, 150-W connector type has “Recognized” approval. The weight indicated is the weight of the open-frame type. (Includes the covers for 300-W and 600-W models) Class 2 approved for 10-W, 25-W (except for 5-V output), and 50-W (only for 24-V output) models. ■ Reference Value Item Value Definition Reliability (MTBF) 135,000 hours min. MTBF stands for Mean Time Between Failures, which is calculated according to the probability of accidental device failures, and indicates reliability of devices. Therefore, it does not necessarily represent a life of the product. Life expectancy 10 yrs. min. The life expectancy indicates average operating hours under the ambient temperature of 40°C and a load rate of 50%. Normally this is determined by the life expectancy of the builtin aluminum electrolytic capacitor. L-84 Switching Power Supply S82J Connections ■ Block Diagrams S82J-010@@@@ (10 W) S82J-025@@@@ (25 W) Fuse* Smoothing circuit Rectifier +V AC (L) Input Noise Noisefilter filter DC Output −V AC (N) Inrush current protection circuit Rectifier and smoothing circuit * Fuse capacity: 10 W, 1 A 25 W, 2 A Control circuit Overload detection circuit Detector Photocoupler S82J-050@@@@ (50 W) Fuse* AC(L) Input +V DC Output Noise filter AC(N) Rectifier Inrush current Smoothing protection circuit circuit Rectifier and smoothing circuit −V * Fuse capacity: 3 A Control circuit Overload detection circuit Detector Photocoupler S82J-100@@@@ (100 W, 5-/12-/15-V Output) Fuse* +V AC (L) Noise Noisefilter filter DC Output −V AC (N) * Fuse capacity: 5 A 100 or 200 V Rectifier and Inrush current protection circuit (selected auto- smoothing matically) circuit Rectifier and smoothing circuit Control circuit Detector Overload detection circuit Photocoupler Power Supplies Input Overvoltage detector Overvoltage protection circuit (5 V only) Switching Power Supply S82J L-85 S82J-10024@@ (100 W, 24-V Output) AC(L) Fuse (5 A) +V Input DC Output Noise filter −V AC(N) Rectifier Inrush current Smoothing protection circuit circuit Rectifier and smoothing circuit Control circuit Overload detection circuit Detector Photocoupler Overload detection circuit Photocoupler S82J-15024@@ (150 W) AC (L) Fuse (8 A) Input +V DC Output Noise filter AC (N) Inrush current protection circuit −V Rectifier and smoothing circuit Rectifier 100 or 200 V (selected automatically) Control circuit Detector Overcurrent detector Photocoupler S82J-30024@ (300 W) Rectifier and smoothing circuit Fuse (10 A) Input DC Output Noise filter Inrush current protection circuit Rectifier and smoothing circuit 100/200 V (selectable) Control circuit Overcurrent detector Detector Photocoupler Overvoltage detector Photocoupler Parallel operation selector L-86 Switching Power Supply S82J Note: Short-circuit the input voltage selector terminals if the input is 100 to 120 VAC. Keep the terminals open if the input is 200 to 230 VAC. S82J-60024@ (600 W) Fuse 20 A Rectifier and smoothing circuit Input Noise filter DC Output Inrush current protection circuit Rectifier and smoothing circuit 100/200 V (selectable) Fan Control circuit Overcurrent detector Detector Photocoupler Overheat detector Overvoltage detector Photocoupler Note: Short-circuit the input voltage selector terminals if the input is 100 to 120 VAC. Keep the terminals open if the input is 200 to 230 VAC. Parallel operation selector ■ Installation 10-/25-/50-/100-/150-W Models Note: 10-/25-/50-/100 (24 V)-W models are available only as Front Terminal Models. Front Terminals Model Top Terminals Model Connector Model 5 5 5 6 6 6 +V 1 +V +V 1 −V −V 3 GR 1 3 AC (L) GR 3 GR 2 AC (L) NC AC (N) AC (L) 2 2 AC (N) −V AC (N) 9 Types of Connector for the Connector Model (Housing and Terminal Not Included) Connector Connector on the PCB side Housing Terminal Input Wafer (Made by Molex) 5277-04A-RE Housing (Made by Molex) 5196-04-RE or Terminal (Made by Molex) 5194T or 5196-04 5194TL Output Tab header (Made by Nippon AMP) 1-178140-5 Rise housing (Made by Nippon AMP) 1-178129-6 Rise contact (Made by Nippon AMP) 1-175196-5 or 1-175218-5 Power Supplies Note: The permissible current of the output connector is 8 A per pin. Switching Power Supply S82J L-87 300-W Models 5 6 1 Side view +V +V −V −V AC (L) AC (N) 2 4 GR 3 7 8 600-W Models 65 7 1 −V −V +V +V Side view 8 AC (L) AC (N) GR 1. DC Output Terminals: Connect the load lines to these terminals. 2. Input Terminals: Connect the input lines to these terminals. 4 3 2 Note: A fuse is inserted into the AC (L) side. 3. Ground Terminal (GR): Connect a ground line to this terminal. 4. Input Voltage Selector Terminals: Short-circuit the terminals if the input is 100 to 120 VAC and open the terminals if the input is 200 to 230 VAC 5. Output Indicator (DC ON): Lights while a Direct Current (DC) output is ON. 6. Output Voltage Adjuster (V.ADJ): It is possible to increase or decrease the output voltage by 10%. 7. Protection-ON Alarm Indicator: The red indicator will be lit if the overvoltage (for a 300-/600-W model) or overheat protection (for a 600-W model) circuit is triggered. This indicator will also be lit when overcurrent (for a 600-W model) is detected. 8. Parallel/Single Operation Selector: Set the selector to PARALLEL if the Units are in parallel operation. 9. NC Terminals: Leave unconnected. L-88 Switching Power Supply S82J Engineering Data ■ Derating Curve 10-/25-/50-/100-/150-W Model Open-frame type Covered-type Standard Installation Forced air-cooling (1 m3/min) Natural air-cooling Load (%) Load (%) Forced air-cooling (1 m3/min) Natural air-cooling Note: The derating curve shown is for standard installation. The derating curve depends on the mounting direction of the Power Supply. Ambient temperature (°C) Ambient temperature (°C) 300-W Model 120 Parallel Operation Forced air-cooling (1 m3/min) (Standard mounting) 100 Load (%) Load (%) Single Operation Standard mounting 120 20 mm min. Natural air-cooling (Standard mounting) Forced air-cooling (1 m3/min) (Side mounting) Natural cooling (Side mounting) 20 mm min. Forced air-cooling (1 m3/min) (Standard mounting) 100 Natural air-cooling (Standard mounting) Forced air-cooling (1 m3/min) (Side mounting) 20 mm min. 20 mm min. Natural cooling (Side mounting) Ambient temperature (°C) Ambient temperature (°C) 600-W Model Parallel Operation 120 100 Standard Mounting 120 20 mm min. 100 20 mm min. Ambient temperature (°C) 20 mm min. 20 mm min. Power Supplies Load (%) Load (%) Single Operation Ambient temperature (°C) Note: Provide a minimum clearance of 20 mm between the Power Supplies. Switching Power Supply S82J L-89 100 (5, 24 V)-W Models The Power Supply is provided with an overload protection function that protects the load and the power supply from possible damage by overcurrent. When the output current rises above 105% to 160% of the rated output current, the protection function is triggered, decreasing the output voltage. When the output current falls within the rated range, the overload protection function is automatically cleared. The Power Supply is provided with an overvoltage protection function that protects the load and the Power Supply from possible damage by overvoltage. When the output voltage rises above a set value (120% of the rated output voltage), the protection function is triggered, shutting off the output voltage. If this occurs, reset the Power Supply by turning it off for 1 minutes min. and then turning it on again. 10- to 100 (24 V)-W Models 100 (5, 12, 15 V)-W, 150-W, and 300-W Models Intermittent operation Output voltage (V) 10- to 300-W Models Output voltage (V) ■ Overvoltage Protection Output voltage (V) ■ Overload Protection Rated output voltage 0 50 100 Output current (%) Overvoltage protection operating Variable range Rated value Output current (%) Note: 1. If the S82J is connected to a load with a built-in DC-DC converter, the overload protection function may be triggered at startup, and consequently the S82J may not operate. 2. Do not continue using the S82J with the output terminals short-circuited or the overcurrent condition continued, otherwise the internal elements of the S82J may be damaged or broken. 3. In actual operation, the output voltage may not fall to 0 V when the overload protection function is triggered. Even with short-circuits on the load side, the drop in voltage will vary depending on factors such as the impedance in the load line. 4. The overload protection function is activated at 105% of the rated output current for 300-W models. 600-W Models If an excessive current flows for 5 s or more, the output will be turned off and simultaneously protection-ON alarm indicator will be lit. To reset the S82J, turn off the input voltage, leave the S82J for at least three minutes, and then apply the input voltage again. Note: Do not continue using the S82J with the output terminals shortcircuited or the overcurrent condition continued, otherwise the internal elements of the S82J may be damaged or broken. 300- and 600-W Models If a voltage that is 120% of the rated output voltage or above is output, the output voltage will be turned off and simultaneously protection-ON alarm indicator will be lit. To reset the S82J, turn off the input voltage, leave the S82J for at least three minutes if it is a 600-W model or at least 90 seconds if it is a 300-W model, and then apply the input voltage again. ■ Overheat Protection Function 600-W Model Only If the internal temperature of the S82J rises excessively as a result of fan failure or any other reason, the overheat protection circuit will be triggered to protect the internal elements of the S82J and simultaneously a protection-ON alarm indicator will be lit. To reset the S82J, turn off the input voltage, leave the S82J for at least three minutes, and then apply the input voltage again. ■ Inrush Current, Startup Time, Hold Time Input ON AC input voltage Input OFF Inrush current on input application AC input current 96.5% 90% Output voltage L-90 Switching Power Supply S82J Startup time Hold time (20 ms min.) Dimensions Note: All units are in millimeters unless otherwise indicated. Open-frame type and covered type have the same dimensions. ■ Front-mounting Bracket Type 12 max. S82J-010@@@ (10 W) 90±1 Mounting Holes (Surface Screw Mounting) 3.5 Side Mounting 65±0.5 97±1 Two, M3 5 5 M3.5 terminal screw 65±0.5 82±0.5 Two, 3.5 dia. 3.5 dia. 78±0.5 6.5 82±0.5 3.5 28 17.5 50±0.5 15 Bottom Mounting 35±1 Two, M3 Two, M3 For track mounting bracket (4 mm deep max.) 78±0.5 124±1 12 max. S82J-025@@@ (25 W) Mounting Holes (Surface Screw Mounting) 3.5 Side Mounting 65±0.5 97±1 Two, M3 6 5 116±0.5 6.5 Two, 3.5 dia. 3.5 dia. 112±0.5 M3.5 terminal screw 116±0.5 3.5 Bottom Mounting 28 17.5 21.5 83±0.5 65±0.5 Two, M3 40±1 Two, M3 For track mounting bracket (4 mm deep max.) 112±0.5 S82J-050@@@ (50 W) 12 max. 161±1 Mounting Holes 3.5 Side Mounting Two, M3 65±0.5 97±1 65±0.5 7 5 153±0.5 153±0.5 Two, 3.5 dia. M3.5 terminal screw 3.5 dia. 20 10 22 127±0.5 Bottom Mounting 3.5 20±0.5 28 40±1 Three, M3 For track mounting bracket (4 mm deep max.) Power Supplies 150.5±0.5 6.5 Two, M3 150.5±0.5 Switching Power Supply S82J L-91 12 max. S82J-10024@ (100 W, 24-V Output) 170±1 Mounting Holes 4.5 Side Mounting Two, M3 97±1 65±0.5 65±0.5 162±0.5 162±0.5 5 M3.5 terminal screw 7 4.5 dia. Three, M4 6.5 4.5 dia. Bottom Mounting 160±0.5 Two, M3 4.5 25±0.5 27.5 50±1 28±0.5 15 15 S82J-100@@@ (100 W, 5-/12-/15-V Output) S82J-15024@ (150 W) 160±0.5 100±0.5 198 (see note) 188 4 max. Mounting Holes (Surface Screw Mounting) Side Mounting 4.5 8.1 89±0.5 Two, M4 97 9.5 82±0.8 M4 x 8 7±0.3 4.5 dia. 3±0.25 180±0.5 180±0.5 Mounting holes (on both sides) 4.5 dia. 178±0.5 3±0.25 Note: Top terminal and connector models are 188 mm wide. Bottom Mounting Two, M4 4.5 27.5±0.3 Three, M4 (6 mm max. deep) S82J-30024@ (300 W) Nine, M4 terminal screws 4 max. (19) 100±0.5 25±0.5 50 35±0.5 15 178±0.5 55±0.3 Eight, M4 holes (depth: 8 max. on both sides) Mounting Holes (Surface Screw Mounting) Side Mounting Side Four, 4.5 dia. 50±0.5 Four, M4 holes (depth: 8 max.) 150±0.5 Bottom Mounting Four, 4.5 dia. 100±0.5 150±0.5 L-92 Switching Power Supply S82J S82J-60024@ (600 W) Eight, M4 holes (depth: 8 max. on both sides) Mounting Holes (Surface Screw Mounting) Side Mounting Four, 4.5 dia. 50±0.5 Four, M4 holes (depth: 8 max. on one side) Four, M4 holes (depth: 8 max.) 150±0.5 Bottom Mounting Nine, M4 terminal screws Four, 4.5 dia. 100±0.5 150±0.5 Dimensions with Mounting Bracket (Provided) 10-/25-/50-/100 (24 V)-W Models Mounting Holes 11 1.5 Using the Mounting Bracket Attach the mounting bracket to the panel and loosely tighten the two screws. Insert the projected parts of the bracket (b) to the square holes of the power supply (a). Then securely tighten the screws. 4.6 15±0.2 9 60 Two, 3.5 dia. 74 Two, M3 60 Note: The mounting screws are order separately. 4.6 11 5 20 20 31.5 4.7 (b) 15 t=1.0 (a) 20.5 Power supply unit Mounting bracket (b) (a) 100- (5, 12, 15 V) and 150-W Models Mounting with Brackets Mounting bracket 6.5 11 Power Supplies 5 dia. 120 max. 110±0.5 23.5 1.5 30±0.5 Two, 5 dia. 38 t=0.8 Note: The brackets are for front-mounting. Switching Power Supply S82J L-93 300-W Models 10 dia. Two, 5 dia. Note: To provide ventilation space, the body will shift forward by 21.6 mm from the mounting surface. t= 1.6 600-W Models Note: To provide ventilation space, the body will shift forward by 23.6 mm from the mounting surface. L-94 Switching Power Supply S82J ■ DIN Track Mounting Bracket Type S82J-010@@@D (10 W) 7 max. 12 max. 9 max. when slided out S82J-025@@@D (25 W) 7 max. 12 max. 9 max. when slided out S82J-050@@@D (50 W) 7 max. 12 max. 9 max. when slided out 7 max. 12 max. 9 max. when slided out Power Supplies S82J-10024@D (100 W, 24-V Output) Switching Power Supply S82J L-95 S82J-100@@@D (100 W, 5-/12-/15-V Output) S82J-15024@D (150 W) 7 max. 4 max. 9 max. when slided out ■ DIN Track Mounting Bracket (Order Separately) Can be used with 10-W to 150-W Front-mounting Bracket models. If DIN track mounting is necessary, use a DIN Track Mounting Bracket. Refer to the S82Y DIN Track Mounting Bracket datasheet for details. ■ Front-mounting Bracket for S82J-10024@ Power Supply (Order Separately) Product Front-mounting Bracket Model number Dimensions S82Y-J10F Mounting hole dimensions Three, 4.5-dia. holes 40 Three, M4 50 50 180 Note: These Front-mounting Brackets cannot be used with S82J 100-W (5, 12, or 15-V) or 150-W models. Switching Power Supply S82J 20 15 t = 1.6 L-96 (Unit: mm) 15 Precautions Mounting 100 (5, 12, 15 V)/150-/300-/600-W Models To improve and maintain the reliability of the Power Supply over a long period of time, adequate consideration must be given to heat radiation. (A) Side mounting (except for 300- and 600-W models) The Power Supply is designed to radiate heat by means of natural air-flow. Therefore, mount the Power Supply so that air flow takes place around the Power Supply. (C) Bottom mounting (secured with screws from the back of the Switching Power Supply) (B) Bottom mounting (secured with screws from the inside of the Switching Power Supply) (except for 300- and 600-W models) When mounting the Power Supply, mounting it to a metal plate is recommended. When mounting two or more Power Supplies side-by-side, allow at least 20 mm spacing between them, as shown in the following illustration. (B) Forced air-cooling is recommended. (A) Air (C) 20 mm min. Metal plate (D) Front mounting Front mounting is possible with the mounting brackets provided. Refer to Dimensions. Mounting Methods The following mounting methods are available. 10-/25-/50-/100 (24 V)-W Models (A) Side mounting (B) Bottom mounting (C) Front mounting (see Accessories) Mounting brackets (provided) Metal plate (B) Power Supplies (A) Switching Power Supply S82J L-97 Generating Output Voltage (±) An output of ± can be generated by using two Power Supplies as shown below, because the Power Supply produces a floating output. Parallel Operation +V +V INPUT −V Load +V Load Only 300- and 600-W models can be in parallel operation. Do not operate any other models in parallel. The output of the models in parallel operation is a maximum of 80% of the rated output. 0V INPUT −V With the S82J-050@@@@ or S82J-10024@@, if the load is shorted a reverse voltage may result in the Power Supply causing deterioration and damage. It is recommended that diodes are connected as shown in the previous diagram (D1, D2). −V If operation amplifiers as loads are connected in series, connect a diode between the positive and negative output terminals of each Switching Power Supplies as shown in the illustration below. Without these diodes, the Power Supply may not start when power is turned on, possibly damaging internal circuits over a period of time. Use Schottky barrier diodes with a low forward voltage (VF). Other types of diodes will not be effective. Guidelines for the dielectric strength and current of the diodes are as follows: Set the parallel operation selector to PARALLEL if the Units are in parallel operation and make sure that the thickness and the length of all wires connected to the load are the same to ensure that the wires will have no voltage drop differences. Fan Replacement The service life of the fan is approximately 50,000 hours (at 25°C). The service life varies, however, depending on the ambient temperature or other surrounding environmental conditions such as dust. As a preventive maintenance measure, replace the fan within two years if it is used at an ambient temperature of 40°C. Fans are available as replacements. Dielectric strength: At least twice the rated output voltage of the Power Supply Forward current: At least twice the rated output current No diodes are required for models that allow series operation. +V INPUT D1 Load −V Load Load +V D2 INPUT −V Model: S82Y-JFAN Series Operation Only models with power ratings of 50/100/150/300/600 W allow series operation. As shown in the following diagram, the output voltage from each Switching Power Supply can be added. +V Fan Set: Fan (above), four M4 x 35 sems screws, instruction sheet, and packing case Replace the fan as shown in the following illustration. D1 INPUT −V Load +V INPUT −V D2 ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. Cat. No. M047-E1-07 L-98 In the interest of product improvement, specifications are subject to change without notice. Switching Power Supply S82J