(Stick Controller) RKJXK/RKJXV Series987KB

RKJXK ThumbPointerTM(Stick Controller)
RKJXV
Compact size, standard type. Also available with lever return
mechanism
■ Typical Specifications(Potentiometer)
Items
RKJXK
Rated power
RKJXV
0.0125W
Maximum operating voltage
50V AC, 5V DC
Operating angle
60°±6°
23°max. in each
direction ※
Operating force
8mN・m max.
(Not lever return type)
6±4mN・m
(Lever return type)
14±10mN・m
100,000 cycles
2,000,000 cycles
Operating life
Multi Control
Devices
Note
※ If the lever is tilted more than 23°from the vertical position,
operating feel irregularities or return mechanism errors may occur.
Therefore, please do not tilt more than 23°.
■ Typical Specifications(Center-push)
Items
RKJXK
50mA 12V DC
Operating force
5.2±2.6N
+0.5
Travel
+0.5
0.5 −0.4 mm
0.4 −0.3 mm
100,000 cycles
500,000 cycles
Switch
Type
Operating life
7.4±3N
Variable
Resistor Type
Ratings(max.)
RKJXV
Product Line
Product No.
RKJXK122400Y
Lever return
mechanism
RKJXV1224005
Total resistance Resistance
(kΩ)
taper
Minimum order unit(pcs.) Drawing
No.
Japan
Export
1
With
With
RKJXK122000D
RKJXK1210002
Center-push
500
1,000
Without
2
10
Without
B
(0B)
With
3
With
RKJXV1220001
1,600
Without
1,600
4
Packing Specifications
Tray
Product No.
Number of packages(pcs.)
1 case / Japan
1 case / export packing
Export package
measurements(mm)
RKJXK
500
1,000
373×540×225
RKJXV
1,600
1,600
540×360×250
Refer to P.442 for soldering conditions.
437
RKJXK ThumbPointerTM(Stick Controller)
RKJXV
Dimensions
No.
Unit:mm
Photo
PC board mounting hole dimensions
(Viewed from mounting side)
Style
RKJXK1224
25.4
15.5
9
5
Prohibited
wiring area
2
3.1
16
X
Y
Y
20.7
.9
ø7
16
9
5
2.6
5-ø
X
60˚
8.25
ø2
le
ho
19.3
4.5
Multi Control
Devices
.5
ø1
4-
6
1
13.3
hole
6-ø1
4-1.35 1
Square hole
3.7
12.9
7.7
.9
ø7
.6
4-ø2
All directions
60˚
s
hole
5
Switch
Type
6-ø1
X
2
2
9
5
Y
3.1
16
20.7
15.5
Y
Return position
ø2
13.3
Variable
Resistor Type
22.7
16
X
9
RKJXK1210
RKJXK1220
oles
.5 h
4-ø1
3.7
12.9
19.3
Prohibited
wiring area
17.79
13.15
③ ② ①
le
ho
2
1.
Height of boss
0.75
2.5
2
1
8
6
2.
Ø
4-
3
2
1
11.2
Ø
le
c
b
d
4.5
a
4
8.73
le
ho
5
7
10
le
3
18.95
2.9
12.45
Dimention of VR
10.8
2.6
Height to top frame
438
.6
c
d
SW1
46° max.
3
any direction
Any
direction
Ø1
12.65
7
5
ho
ho
Ø
Lever return position
Ø1
.5
4-
21.28
2-
a
b
3
6-
Ø1
13.15
③ ②①
VR2
VR1
RKJXV1224
2.2
6.5
7
8.6
Ø3
8.73
Prohibited wiring area
.5
RKJXK/RKJXV/ThumbPointerTM(Stick Controller)
Dimensions
No.
Unit:mm
Photo
PC board mounting hole dimensions
(Viewed from mounting side)
Style
RKJXV1220
17.5
13.15
46° max.
3
2
1
Ø4
③ ② ①
le
6
8
3
2
1
2.2
7
φ3
.5
8.6
Multi Control
Devices
Lever return position
18.95
2.9
12.45
Dimention of VR
(10.8)
2.6
Any direction
le
ho
4φ
2.
c B
d
SW1
ho
12.65
7
5
8.73
2-φ
1.6
ole
7
VR1
21
13.15
a
b
4
φ1
.5
10
6-φ
1h
VR2
5
③ ②①
8.73
Prohibited wiring area
Height to top frame
Height of boss
Variable
Resistor Type
11.2
0.75
Switch
Type
439
Multi Control Devices
List of Varieties
Variable resistor type
Type
RKJXK
Series
RKJXV
RKJXY
NEW
RKJXU
NEW
Photo
Dimensions
(typical value)
(mm)
W
20.7
17.8
19.6
18.6
D
25.4
21.3
18.1
24.3
H
12.9
11.2
4.9
5.2
Number ofoperating shafts
Shaft material
Single-shaft
Metal
Resin
Directional resolution
Continuous
Directional operating feeling
(tactile feeling)
Without
With / Without
With
With / Without
Center-push switch
Without
Encoder
Without
Operating temperature range
−10℃ to +70℃
Operating
life
Multi Control
Devices
Lever return mechanism
100,000 cycles
2,000,000 cycles
1,000,000 cycles
2,000,000 cycles
Center-push
100,000 cycles
500,000 cycles
ー
ー
ー
ー
ー
ー
ー
ー
ー
ー
Automotive use
Life cycle (availability)
Mechanical
performance
Insulation resistance
100MΩ min. 250V DC
Voltage proof
250V AC for 1 minute
Slider noise
Directional
operating force
8mN・m max. Without Lever return mechanism
6±4mN・m With Lever return mechanism
14±10mN・m
0.43±0.25N
0.73±0.3N
Push operating force
5.2±2.6N
7.4±3N
ー
ー
Lever return precision
Actuator
strength
Environmental
performance
300mV p-p max. by JIS method
Push / pull
directions
Operating
direction
±5°
50N min.(Push/Pull)
±0.1mm
98N min.(Push),50N min.(Pull) 100N min.(Push),49N min.(Pull)100N min.(Push),30N min.(Pull)
0.3N・m
ー
50N
Cold
−30℃ 96h
Dry heat
80℃ 96h
Damp heat
60℃, 90 to 95%RH 96h
Page
Switch
Type
Electrical
performance
Variable
Resistor Type
Directional operation
437
440
441
Variable Resistor Type Multi Control Devices Soldering Conditions・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 442
Variable Resistor Type Multi Control Devices Cautions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 442
433
Variable Resistor Type / Soldering Conditions
Reference for Manual Soldering
Series
Tip temperature
Soldering time
No. of solders
350℃max.
3s max.
1 time
RKJXK, RKJXV
Reference for Dip Soldering
Series
Preheating
Soldering surface temperature
Heating time
Dip soldering
Soldering temperature Soldering time
No. of solders
RKJXK
90 to 100℃
45s max.
260℃
5s
1 time
RKJXV
90 to 100℃
60s max.
260℃
5s
1 time
Variable Resistor Type / Cautions
Multi Control
Devices
〔Circuit Used for Analog Stick Controller〕
3
Fig.A.Voltage divider type
We recommend you use the variable resistor in a voltage
divider type as shown in Fig. A.
3
2
V
2
Variable
Resistor Type
Since this pot is designed to use with its output is
connected directly to A /D port. lmpedance is considered
to be mega ohm level. Then contact resistance in the pot
is higher. Please refer to Flg-1. So when you use it in the
circuit like Flg-2.Please make sure that impedance should be
over than 1M-ohm.
V
1
〔Impedance on the Output Side〕
[Fig.1]
Switch
Type
〔Dew Condensation〕
3
[Fig.2]
2
3
2
1
p
Avoid using the product when condensation or drops of water might occur
inside the product. Otherwise, insulation deterioration or shorting may occur.
〔Soldering〕
3
A/D
1
p
3
1
2
A/D
1
Terminal
Solder
PC board
Do not employ wiring designs and soldering methods as illustrated in the schematic drawing. Molten
solder flowing over the upper surface of PC board can cause imperfect contacts. Solder all metal
inserted fixing including terminals & metal lugs into a substrate.
〔Stress Being Applied to the Terminals〕
Always be careful not to apply excessive stress on the terminals. Design appropriate soldering conditions.
〔Handling of Variable Resistors Equipped with Switches〕
Exercise care when packing or storing. Packaging or storing while load is applied to the shaft may
cause a malfunction in performance.
〔Storage〕
① Store the products as delivered, at a normal temperature and humidity, without direct sunshine and
corrosive gas ambient. Use them at an earliest possible timing, not later than six months upon receipt.
② After breaking the seal, keep the products in a plastic bag to shut out ambient air, store them in the same
environment as above, and use them up as soon as possible.
③ Do not stack too many switches.
The above operation notes are quoted from the
“Precaution and Guideline of Potentiometer for Electrical Devices”, a technical report issued by the Japan
Electronics and Information Technology Industries Association EIAJ RCR-2191A(in March 2002).
For details, refer to the original technical report.
442
2
1
pppp
Solder
A/D
p
p