IES-0852 - LevelOne

IES-0852
4 x 802.3at PoE + 4 FE Web Smart Switch -40 to 75C, DIN-rail
User Manual
v1.00 - 1206
Preface
This manual describes how to install and use the Hardened Web-Smart PoE & High Power
PoE Ethernet Switch. This switch introduced here is designed to deliver full scalability with
web-based management functions. Capable of operating at temperature extremes of
-40°C to +75°C, this is the switch of choice for harsh environments constrained by space.
Port 1 to port 4 on this switch supports IEEE802.3af Power over Ethernet (PoE) Power
Sourcing Equipment (PSE) and can detect an IEEE802.3af compliant Powered Device (PD).
Using external 48VDC power inputs through Terminal Block or Power Jack, data and power
can be transmitted to a Powered Device (PD) over the same twisted-pair Ethernet cable
through port 1 to port 4 on the switch.
Port 1 to port 4 on this switch also supports High Power PoE Power Sourcing Equipment
(PSE) and can detect a Powered Device (PD). Using external 55VDC power inputs through
Terminal Block or Power Jack, data and power can be transmitted to a Powered Device (PD)
over the same twisted-pair Ethernet cable through port 1 to port 4 on the switch.
To get the most out of this manual, you should have an understanding of Ethernet
networking concepts.
In this manual, you will find:





Features on the Hardened Web-Smart PoE Ethernet Switch
Illustrative LED functions
Installation instructions
Management Configuration
Specifications
IES-0852 User Manual
Page 2
Table of Contents
OVERVIEW ........................................................................................................................... 4
HARDENED WEB-SMART POE ETHERNET SWITCH..............................................................................................4
FEATURES ...............................................................................................................................................................5
PACKAGE CONTENTS .............................................................................................................................................5
FRONT PANEL DISPLAY .........................................................................................................................................6
POWER INPUT ........................................................................................................................................................7
DIN RAIN MOUNT .................................................................................................................................................8
10/100BASE-TX CONNECTOR ............................................................................................................................9
CONNECTING TO YOUR NETWORK .................................................................................................................... 10
Cable Type & Length ............................................................................................................................. 10
Cabling..................................................................................................................................................... 10
WEB MANAGEMENT ......................................................................................................... 11
DEFAULT SETTING .............................................................................................................................................. 11
LOGGING ON TO THE SWITCH ............................................................................................................................. 12
BROWSER INTERFACE ......................................................................................................................................... 13
PoE ............................................................................................................................................................ 14
High Power PoE Operation ................................................................................................................. 15
Port Based VLAN .................................................................................................................................... 16
Priority ...................................................................................................................................................... 17
Diff Serv Code Point .............................................................................................................................. 18
System Setup .......................................................................................................................................... 19
Firmware Upgrade ................................................................................................................................ 20
SPECIFICATIONS ............................................................................................................... 21
IES-0852 User Manual
Page 3
Overview
Hardened Web-Smart PoE Ethernet Switch
LevelOne IES-0852 Industry Ethernet Switch provides 4 PoE ports of 10/100Base-TX plus 4
ports of 10/100Base-TX Ethernet to enable high speed network at mission-critical
environment. This device is designed to be mounted on an industry standard DIN-rail, plus
the clearly visible status LEDs provide simple monitoring of port link activity.
High Reliability
All components are built to withstand harsh environment applications without
compromise where humidity, temperature variation and even shock vibration are
concerns, including Electric & Utility, Critical Infrastructure, Transportation and
Surveillance Security. This device operates under -40 to 75 Celsius (-40 to 167 Fahrenheit)
temperature.
Web Management
Web-based GUI management features implementation of Port-based VLAN, IEEE802.1p
QoS, Prioritised DSCP, set up Admin Password with ease. Plus, the Power over Ethernet
ports can be On / Off and limits the power budget remotely
Power over Ethernet
This switch is Power Sourcing Equipment (PSE), and it is fully complied with IEEE 802.3at
PoE standard at maximum 30W power budget per port. It helps to save infrastructure
wiring costs dramatically by eliminating electric wiring and less UPS needed. Also, it is
compatible with IEEE802.3af standard PD devices.
Safety
This device has been tested under UL508 standard for Industrial Control Equipment to
endurance under test turn on and
highly reliability and safety measurement to ensure field hardened, especially for the harsh
environment.
IES-0852 User Manual
Page 4
Features


















Complies with NEMA TS1/TS2 Environmental requirements such as temperature, shock,
and vibration for traffic control equipment.
Complies with EN61000-6-2 & EN61000-6-3 EMC Generic standard immunity for
Industrial environment.
Manageable via Web browser interface.
Supports IEEE802.3af Power over Ethernet (PoE) Power Sourcing Equipment (PSE).
High Power PoE design up to 30W (enhancement of IEEE802.3af PoE).
Supports IEEE802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps-full/half-duplex;
Auto MDI/MDIX.
100Base-FX: Multi mode SC or ST type, Single mode SC or ST type. 100Base-BX: WDM
Single mode SC type.
Supports 1024 MAC addresses. Provides 1M bits memory buffer.
Store-and-forward mechanism.
Full wire-speed forwarding rate.
Alarms for power and port link failure by relay output.
PoE: Redundant 48VDC Terminal Block power inputs and 48VDC DC JACK power input
for 15.4W per PoE port. Operating voltage and Max. current consumption: 1.5A @
48VDC. Power consumption: 72W Max.
High Power PoE: Redundant 55VDC Terminal Block power inputs and 55VDC DC JACK
power input for 30W per High Power PoE port. Operating voltage and Max. current
consumption: 2.3A @ 55VDC. Power consumption: 130W Max.
-40℃ to 75℃ (-40℉ to 167℉) operating temperature range. Tested for functional
operation @ -40℃ to 85℃ (-40℉ to 185℉). Web-Smart function operating temperature
@ -20℃ to 85℃ (-4℉ to 185℉).
Reset button on front panel.
Front panel port status LEDs.
Hardened aluminum case.
Supports DIN-Rail, Panel, or Rack Mounting installation.
Package Contents
When you unpack the product package, you shall find the items listed below. Please
inspect the contents, and report any apparent damage or missing items immediately to
your authorized reseller.



IES-0852 Hardened Web-Smart High Power PoE Ethernet Switch
Quick Installation Guide
CD User Manual
IES-0852 User Manual
Page 5
Front Panel Display
LED
PW 1,2,3
Status
Description
Steady
Power On
Off
Power Off
10/100Base-TX or 100Base-FX/BX
LNK/ACT
PoE
(High Power)
IES-0852 User Manual
Steady
Network connection is established
Flashing
Transmitting or Receiving data
Steady
Power Device (PD) is connected
Off
Power Device (PD) is disconnected
Page 6
Power Input
PW1
Terminal Block
PW2
PW3
+
48, 55VDC (High Power)
Power Ground
+
48, 55VDC (High Power)
Power Ground
DC Jack
48, 55VDC (High Power)
Earth Ground
Relay Output
0.1A @ 24VDC
*Warning signal disable for following:
DC Jack
1. The relay contact closes if Power1 and Power2 are both failed but Power3
on.
2. The relay contact closes if Power3 is failed but Power1 and Power2 are
both on.
PW3
DC Jack
48, 55VDC (High Power)
Special Note:
The relay output is normal open position when there is no power to the switch. Please do
not connect any power source to this terminal to prevent shorting your power supply.
IES-0852 User Manual
Page 7
DIN rain Mount



Fix the DIN rail attachment plate to the back panel of the switch.
Installation: Place the switch on the DIN rail from above using the slot. Push the front of
the switch toward the mounting surface until it audibly snaps into place.
Removal: Pull out the lower edge and then remove the switch from the DIN rail.
IES-0852 User Manual
Page 8
10/100Base-TX Connector
The following lists the pin-out of 10/100Base-TX ports.
Pin
PoE Port (1 to 4)
Standard Port (5)
1
Output Transmit Data +
Input Receive Data +
2
Output Transmit Data -
Input Receive Data -
3
Input Receive Data +
Output Transmit Data +
4
Positive (VCC+)
NC
5
Positive (VCC+)
NC
6
Input Receive Data -
Output Transmit Data -
7
Negative (VCC-)
NC
8
Negative (VCC-)
NC
IES-0852 User Manual
Page 9
Connecting to Your Network
Cable Type & Length
It is necessary to follow the cable specifications below when connecting the switch to your
network. Use appropriate cables that meet your speed and cabling requirements.
Cable Specifications
Speed
Connector
10Base-T
RJ-45
Port Speed
Half/Full Duplex
10/20 Mbps
100Base-TX
RJ-45
100/200 Mbps
100Base-FX
ST, SC
100/200 Mbps
100Base-FX
ST, SC
100/200 Mbps
Cable
2-pair UTP/STP
Cat. 3, 4, 5
2-pair UTP/STP
Cat. 5
MMF (50 or
Max.
Distance
100 m
100 m
2 km
20, 40, or 75
km
Cabling
Step 1: First, ensure the power of the switch and end devices are turned off.
<Note> Always ensure that the power is off before any installation.
Step 2: Prepare cable with corresponding connectors for each type of port in use.
Step 3: Consult Cable Specifications Table on previous page for cabling requirements
based on connectors and speed.
Step 4: Connect one end of the cable to the switch and the other end to a desired device.
Step 5: Once the connections between two end devices are made successfully, turn on the
power and the switch is operational.
IES-0852 User Manual
Page 10
Web Management
The switch provides a browser interface that lets you configure and manage the switch
remotely.
applications directly in your web browser by entering the IP address of the switch. You can
then use your web browser to list and manage switch configuration parameters from one
Web-Based Browser Management
The switch provides a web-based browser interface for configuring and managing the
switch. This interface allows you to access the switch using a preferred web browser.
This chapter describes how to configure the switch using its web-based browser interface.
Default Setting
IP address: 192.168.1.10
User Name: admin
Password: [Blank]
IES-0852 User Manual
Page 11
Logging on to the switch
SWITCH IP ADDRESS
In your web browser, specify the IP address of the switch. Default IP address is
192.168.1.10.
USER NAME
Enter the factory default user name: admin.
PASSWORD
Enter the factory default password (no password).
Or enter a user-defined password if you followed the instructions later and changed the
factory default password.
OK
IES-0852 User Manual
on to the switch.
Page 12
Browser Interface
The web browser interface provides groups of point-and-click buttons at the left field of
the screen for configuring and managing the switch.
PoE
Port Based VLAN
Priority
Diff Serv Code Point
Bit 0 ~ 31, Bit 32 ~ 63
System Setup
Firmware Upgrade
IES-0852 User Manual
Page 13
PoE
PoE
1. System power budget:
System power budget
and type a new system
power budget.
2. OK:
OK button to update your settings.
3. Enable mode: C
Enable mode drop-down menu to choose Enable or Disable
Enable mode drop-down list to enable or disable Port 1 ~ Port 4 to discover
Powered Device (PD) connected to Port 1 ~ Port 4 of the Switch.
4. Power limit by classification: Check or uncheck Power limit by classification to enable
or disable Port 1 ~ Port 4 to provide power to PD according to classification of
maximum power range used by PD.
5. Fixed power limit(W): First uncheck Power limit by classification to disable Port 1 ~
Port 4 to provide power to PD according to classification of maximum power range
used by PD. Then c
Fixed power limit(W)
and type a new fixed power
limit for Port 1 ~ Port 4 to provide power to PD.
6. Power priority: C
Power priority drop-down menu to choose Low , Middle , or
High
Power priority drop-down list to determine power priority of Port 1
~ Port 4.
7. OK:
OK button to update your settings.
IES-0852 User Manual
Page 14
High Power PoE Operation
This Industrial Web-Smart PoE & High Power PoE Ethernet switch is compliant with the
802.3af and 802.3at High Power standard, providing 30W of pure power to power
demanding devices such as pan-tilt-zoom (PTZ) network cameras, wireless access
bridge/routers and large-screen network video phones et cetera.
This 802.3af High Power switch s PoE operation with 802.3at based PD is highly versatile
and adaptable. Normally, when an 802.3at PD is connected to an 802.3af High Power
compliant switch, the switch will detect that the PD s power requirement is based on class
4 classification outlined in the IEEE802.3at standard, and only attempt to provide 15.4W of
power, which is insufficient to power a 30W 802.3at PD. This is due to the reason that the
30W of power in 802.3af High Power is classified as class 0. However, this 802.3af High
Power switch can support 30W 802.3at PD by setting the switch explicitly to provide a
fixed rate of 30W power to 30W 802.3at PD.
Power limit by classification: Uncheck Power limit by classification to disable Port 1 ~ Port
4 to provide power to 30W 802.3at PD according to classification of maximum power
range used by PD.
Fixed power limit(W): C
Fixed power limit(W)
and type a new fixed power
limit 30W for Port 1 ~ Port 4 to provide power to 30W 802.3at PD.
OK:
OK button to update your settings.
IES-0852 User Manual
Page 15
Port Based VLAN
Port Based VLAN
1. VLAN.1 ~ VLAN.7: Click and choose Port 1 ~ Port 8 to be added into VLAN.1 ~ VLAN.7.
2. Cancel:
Cancel button to cancel your settings.
3. OK:
OK button to update your settings.
IES-0852 User Manual
Page 16
Priority
Priority
1. Ratio Scheme: Click and choose All High Before Low , 10:1 , 5:1 , or 2:1 ratio scheme.
2. Port 1 ~ Port 8: Click and choose TOS , 802.1p , or Port Priority ( High or Low ) for
Port 1 ~ Port 8.
3. 802.1p Level 7 ~ Level 0: Click and set High or Low priority to queue of 802.1p Level
7 ~ Level 0.
4. Cancel:
Cancel button to cancel your settings.
5. OK:
OK button to update your settings.
IES-0852 User Manual
Page 17
Diff Serv Code Point
Diff Serv Code Point
Bit 0 ~ 31:
1. Diff Serv Code Point: Check and set Bit 0 ~ 31 of Diff Serv Code Point to high priority.
2. Cancel:
Cancel button to cancel your settings.
3. OK:
OK button to update your settings.
Bit 32 ~ 63:
1. Diff Serv Code Point: Check and set Bit 32 ~ 63 of Diff Serv Code Point to high priority.
2. Cancel:
Cancel button to cancel your settings.
3. OK:
OK button to update your settings.
IES-0852 User Manual
Page 18
System Setup
System Setup
System Configuration:
1. DHCP Client: Click and choose Enable or Disable to enable or disable the Switch as
DHCP client to be automatically supplied an IP address, gateway address, and subnet
mask from DHCP server.
2. IP Address: C
IP Address text box and type a new address to change the IP
Address.
3. Subnet Mask: C
Subnet Mask text box and type a new address to change the
Subnet Mask.
4. Default Gateway: C
Default Gateway text box and type a new address to change
the Default Gateway.
5. Cancel:
Cancel button to cancel your settings.
6. OK:
OK button to update your settings.
Password Configuration:
1. Old Password:
Old Password
and type in the old password.
2. New Password:
New Password
and type in a new password.
3. Confirm Again:
Confirm Again
. Type the same password in New
Password
again to verify it.
4. Cancel:
Cancel button to cancel your settings.
5. OK:
OK button to update your settings.
System Reset/Restore to default:
1. Load Default:
Load Default button to restore the default settings of the Switch.
2. Reset System:
Reset System button to restart the Switch.
IES-0852 User Manual
Page 19
Firmware Upgrade
Firmware Update
1. Cancel: C
2. Update: C
Cancel button to cancel firmware update request.
Update button and wait for firmware update request being processed.
IES-0852 User Manual
Page 20
Specifications
Applicable Standards
Switching Method
Forwarding Rate
10Base-T
100Base-TX
100Base-FX/BX
Performance
Cable
10Base-T
100Base-TX
100Base-FX
100Base-BX
LED Indicators
Dimensions
Net Weight
Power Input
Operating Voltage &
Max. Current
Consumption
Power Consumption
IEEE802.3 10Base-T
IEEE802.3u 100Base-TX/FX
Store-and-Forward
10 / 20Mbps half / full-duplex
100 / 200Mbps half / full-duplex
200Mbps full-duplex
14,880pps for 10Mbps
148,810pps for 100Mbps
4-pair UTP/STP Cat. 3, 4, 5 Up to 100m (328ft)
4-pair UTP/STP Cat. 5 Up to 100m (328ft)
Per unit Power status (Power1, Power2, Power3)
Per port
PoE & High Power PoE: PoE, Link/ACT
10/100TX, 100FX: Link/ACT
68mm (W) x 110mm (D) x 135mm (H)
1Kg (2.2lbs.)
Terminal Block: 48, 55VDC (High Power)
DC Jack: 48, 55VDC (High Power)
PoE: 1.5A @ 48VDC
High Power PoE: 2.3A @ 55VDC
PoE: 72W Max.
High Power PoE: 130W Max.
-40°C to 75℃ (-40℉ to 167℉)
Operating
Tested for functional operation @
Temperature
-40℃ to 85℃ (-40℉ to 185℉)
Web-Smart function operating temperature @
-20℃ to 85℃ (-4℉ to 185℉)
-40°C to 85℃ (-40℉ to 185℉)
Storage Temperature
5%-95% non-condensing
Humidity
FCC Part 15, Class A
EMI
EN61000-6-3: EN55022, EN61000-3-2, EN61000-3-3
EN61000-6-2:
EMS
EN61000-4-2 (ESD Standard)
EN61000-4-3 (Radiated RFI Standards)
EN61000-4-4 (Burst Standards)
EN61000-4-5 (Surge Standards)
EN61000-4-6 (Induced RFI Standards)
EN61000-4-8 (Magnetic Field Standards)
IEC60068-2-6 Fc (Vibration Resistance)
Environmental Test
IEC60068-2-27 Ea (Shock)
Compliance
IEC60068-2-32 Ed (Free Fall)
NEMA TS1/2 Environmental requirements for traffic control equipment
IES-0852 User Manual
Page 21