pdf-download PCQA24

POSICHRON®
PCQA24
Square Profile Housing with Analog Output
POSICHRON® position sensor in square profile
• Protection class up to IP67/IP69K
• Measurement range 0 ... 100 to 0 ... 5750 mm
• Absolute position measurement
• Easy installation with mounting brackets
• Wear free position magnet
• Contactless
•Also available with guided
position magnet
• Analog output
Specifications
Output
Voltage
Current
Refer to output specification
Up to 1 kHz, depending on the measurement range
Ranges >500 mm: L10 = ±0.10 % f.s.
L02 = ±0.02 % f.s.
Ranges ≤500 mm: L10 = ±0.5 mm
L02MM = ±0.2 mm
±3 µm
AlMgSi1 / Zn / V4A
IP67 (optional IP67/IP69K; connector version: with
mating connector only)
EN 60068-2-27:2010, 50 g 11 ms, 100 shocks
EN 60068-2-6:2008, 20 g 10 Hz-2 kHz, 10 cycles
Connector M12, 8 pin / cable 2 m
Refer to output specification
Resolution
Sampling rate
Linearity
Repeatability
Housing material
Protection class
Shock
Vibration
Connection
EMC, temperature
Order code PCQA24
1 channel
PCQA24
Model name
Measurement range (in mm)
100 ... 5750 (in 10 mm increments)
other lengths upon request
Output
U1 = 0 ... 10 V signal conditioner
U1/H = U1 with Alarm_HOLD (see page 11)
U2 = 0.5 ... 10 V signal conditioner
U2/U; U2/H = U2 with Alarm_LOW; U2 with Alarm_HOLD (see page 11)
U8 = 0.5 ... 4.5 V signal conditioner
U8/U; U8/H = U8 with Alarm_LOW; U8 with Alarm_HOLD (see page 11)
I1 = 4 ... 20 mA signal conditioner (3 wire)
I1/U; I1/H = I1 with Alarm_LOW; I1 with Alarm_HOLD (see page 11)
Function and characteristics output
P1A = Position Magnet 1, increasing
P1D = Position Magnet 1, decreasing
PMU = Start value, direction & end value adjustable by the customer
Linearity
L02 / L02MM / L10 (for definition see "Specifications" above)
Connection
M12 = Connector M12, 8 pin
KAB2M = Cable, standard length 2 m, other lengths upon request
Order code mounting set (see page 7)
DB-PCQA24-E-2013-11
www.asm-sensor.com
PCQA-BFS1
1/16
© ASM GmbH
[email protected]
POSICHRON®
PCQA24
Square Profile Housing with Analog Output
Order Code PCQA24
2 channel,
Model name
configurable
PCQA24
Measurement range (in mm)
100 ... 5750 (in 10 mm increments)
other lengths upon request
Output
U1 = 0 ... 10 V signal conditioner
U1/H = U1 with Alarm_HOLD (see page 11)
U2 = 0.5 ... 10 V signal conditioner
U2/U; U2/H = U2 with Alarm_LOW; U2 with Alarm_HOLD (see page 11)
U8 = 0.5 ... 4.5 V signal conditioner
U8/U; U8/H = U8 with Alarm_LOW; U8 with Alarm_HOLD (see page 11)
I1 = 4 ... 20 mA signal conditioner (3 wire)
I1/U; I1/H = I1 with Alarm_LOW; I1 with Alarm_HOLD (see page 11)
Function and characteristics output 1
P1A = Position magnet 1, increasing
P1D = Position magnet 1, decreasing
DA = Difference magnet 1/2, increasing (2 magnets required)
DD = Difference magnet 1/2, decreasing (2 magnets required)
Function and characteristics output 2
P2A = Position magnet 2, increasing
P2D = Position magnet 2, decreasing
DA = Difference magnet 1/2, increasing
DD = Difference magnet 1/2, decreasing
2 magnets required
VZx.x = Velocity with direction detection (with 1 magnet only)
VZx.x = Velocity in steps of 0.1 m/s
Example: VZ1.5 towards start position
towards end position
-1.5 m/s
0
+1.5 m/s
Output U2: 0.5 V 5.25 V
10 V
Output I1: 4 mA
12 mA
20 mA
VAx.x = Velocity without direction detection (with 1 magnet only)
VAx.x = Velocity in steps of 0.1 m/s
Example: VA1.5 towards start position
towards end position
-1.5 m/s
0
+1.5 m/s
Output U2:
10 V
0.5 V
10 V
Output I1: 20 mA
4 mA
20 mA
Linearity
L02 / L02MM / L10 (for definition see "Specifications" above)
Connection
M12 = Connector M12, 8 pin
KAB2M = Cable, standard length 2 m, other lengths upon request
1. Order example: PCQA24 - 1000 - I1 - P1A - P2D - L10 - M12
Square profile, measurement range 1000 mm, 2 current outputs 4 ... 20 mA (I1)
Output 1: Position magnet 1, increasing signal (P1A)
Output 2: Position magnet 2, decreasing signal (P2D)
2. Order example: PCQA24 - 1000 - U1 - P1A - VZ1.0 - L10 - M12
Square profile, measurement range 1000 mm, 2 voltage outputs 0.5 ... 10 V (U2)
Output 1: Position magnet 1, increasing signal (P1A)
Output 2: Velocity magnet 1, -1 m/s ... 1 m/s for range 0.5 ... 10 V (VZ1.0)
Order code position magnet/slider (see page 8)
PCMAG ...
Order code mating connecting cable (see page 15)
DB-PCQA24-E-2013-11
www.asm-sensor.com
2/16
KAB-...M-M12/8F/G-LITZE
© ASM GmbH
[email protected]
POSICHRON®
PCQA24
Square Profile Housing with SSI Output
POSICHRON® position sensor in square profile
• Protection class IP67/IP69K
• Measurement range 0 ... 100 to 0 ... 5750 mm
• Absolute position measurement
• Easy installation with mounting brackets
• Wear free position magnet
• Contactless
•Also available with guided position magnet
• Synchronous serial interface (SSI)
Specifications
Output
Resolution
Sampling rate
Linearity
Synchronous serial interface (SSI)
5, 10, 20, 50, 100 µm
Up to 1 kHz, depending on the measurement range
Ranges >500 mm: L10 = ±0.10 % f.s.
L02 = ±0.02 % f.s.
Ranges ≤500 mm: L10 = ±0.5 mm
L02MM = ±0.2 mm
±3 µm
AlMgSi1 / Zn / V4A
IP67 (optional IP67/IP69K; connector version: with
mating connector only)
EN 60068-2-27:2010, 50 g 11 ms, 100 shocks
EN 60068-2-6:2008, 20 g 10 Hz-2 kHz, 10 cycles
8 pin socket / cable 2 m
Refer to output specification
Repeatability
Housing material
Protection class
Shock
Vibration
Connection
EMC, temperature
Order Code PCQA24
PCQA24
/
/
Model name
Measurement range (in mm)
100 ... 5750 (in 10 mm increments)
other lengths upon request
Resolution (in µm)
5 / 10 / 20 / 50 / 100
Output
SSI = Synchronous serial interface
Code
G / D = Gray / Dual
Number of data bits
24 / 25
Linearity
L02 / L02MM / L10 (for definition see "Specifications" above)
Connection
M12 = Connector M12, 8 pin
KAB2M = Cable, standard length 2 m, other lengths upon request
Order code mounting set (see page 7)
PCQA-BFS1
Order code position magnet/slider (see page 8)
PCMAG ...
Order code mating connecting cable (see page 15)
KAB-...M-M12/8F/G-LITZE
Order example: PCQA24 - 2500 - 10 - SSI/G/24 - L10 - M12
DB-PCQA24-E-2013-11
www.asm-sensor.com
3/16
© ASM GmbH
[email protected]
POSICHRON®
PCQA24
Square Profile Housing with CAN Output
POSICHRON® position sensor in square profile
• Protection class IP67/IP69K
• Measurement range 0 ... 100 to 0 ... 5750 mm
• Absolute position measurement
• Easy installation with mounting brackets
• Wear free position magnet
• Contactless
•Also available with guided position magnet
•CANopen bus or
CAN SAE J1939 output
Specifications
Output
Resolution
Sampling rate
Linearity
CANopen bus; CAN SAE J1939
50 µm
Up to 1 kHz, depending on the measurement range
Ranges >500 mm: L10 = ±0.10 % f.s.
L02 = ±0.02 % f.s.
Ranges ≤500 mm: L10 = ±0.5 mm
L02MM = ±0.2 mm
±3 µm
AlMgSi1 / Zn / V4A
P67 (optional IP67/IP69K; connector version: with
mating connector only)
EN 60068-2-27:2010, 50 g 11 ms, 100 shocks
EN 60068-2-6:2008, 20 g 10 Hz-2 kHz, 10 cycles
5 pin socket M12
Refer to output specification
Repeatability
Housing material
Protection class
Shock
Vibration
Connection
EMC, temperature
Order Code PCQA24
PCQA24
Model name
Measurement range (in mm)
100 ... 5750 (in 10 mm increments)
other lengths upon request
Output
CANOP = CANopen bus
CANOP/R = CANopen-Bus with integrated terminating resistance
CANJ1939 = CAN SAE J1939
Linearity
L02 / L02MM / L10 (for definition see "Specifications" above)
Connection
M12/CAN = Connector M12, 5 pin
Order code mounting set (see page 7)
PCQA-BFS1
Order code position magnet/slider (see page 8)
PCMAG ...
Order code bus cable (see page 16)
KAB-...M-M12/5F/G-M12/5M/G - CAN
Order example: PCQA24 - 1000 - CANOP - L10 - M12/CAN
DB-PCQA24-E-2013-11
www.asm-sensor.com
4/16
© ASM GmbH
[email protected]
POSICHRON®
PCQA24
Square Profile Housing
Cable output
39 [1.535]
end position
PCMAG5
26 [1.024]
37,25 [1.467]
54,25 [2.136]
10,2 [0.402]
59,25 [2.333]
start position
PCMAG5
46 [1.811]
total length A = measurement length + 155 [6.102] (e.g.255 [10.039])
58 [2.283]
mounting set PCQA-BFS1
2 ± 1 [0.079 ± 0.039]
35,5 [1.398]
±12 [0.472]
20,9 [0.823]
85 [3.346]
70 [2.756]
measurement length (e.g. 100 [3.937])
Cable: outer diameter 5.2 mm ±0.2 mm, wire: cross sectional area 0.25 mm²
Dimensions in mm [inch]
Dimensions informative only. For guaranteed dimensions consult factory.
Maße in mm [inch]
Zeichnung ist Eigentum der Firma ASM, Vervielfältigung nur mit Genehmigung
Schutzvermerk nach DIN 34 beachten © Copyright by ASM GmbH
10,2 [.402]
Gezeichnet
Datum
11.05.2005
Kontrolliert
Norm
AS M
Änderungen
Benennung
Name
ScF
Maßzeichnung
Tel.: 08123/986-0
Zeichnungsnummer / Datei
Name
Datum
58 [2.283]
2 1 [.079 .039]
35,5 [1.398]
±12 [.472]
15,95 [.628]
measurement length (e.g.100 [3.937])
70 [2.756]
Maße in
Dimensions informative only. For guaranteed dimensions consult factory.
dimensions
Zeichnung ist Eigentum der Firma ASM, Vervielfältigung nur mit Genehmigung
Schutzvermerk nach DIN 34 beachten © Copyright by ASM GmbH
Nicht bemaßte
Werkstückkanten
DIN 6784
Allgemeintoleranzen
+0,1
+0,2
-0,1
-0,2
ISO
2768-mH
Gezeichnet
Datum
29.11.2009
Maßstab
1:1
Name
ScF
Kontrolliert
AS M
AUTOMATION
SENSORIK
MESSTECHNIK
DB-PCQA24-E-2013-11
www.asm-sensor.com
Änderungen
Datum
BMC:
mm [inch]
in mm [inch]
CT:
Werkstoff, Halbzeug
Benennung
PCQA24-ML(100-5750)-(10V|420T)-M12
Maßzeichnung / general drawing
Norm
Status
1
A4
46 [1.811]
mounting set PCQA-BFS1
Dimensions in mm [inch]
Blatt
121404_PCQA24-ML(100-5750)-KAB_001_JMZ.idw
total length A = measurement length + 155 [6.102] (e.g. 255 [10.039])
85 [3.346]
39 [1.535]
26 [1.024]
PCQA24-ML(100-5750)-(10|420T)-KAB
ASM GmbH
Am Bleichbach 18-22
D-85452 Moosinning
AUTOMATION
SENSORIK
MESSTECHNIK
CT:
59,25 [2.333]
end position
PCMAG5
BMC:
Werkstoff, Halbzeug
1:2
2768-mH
start position
PCMAG5
Status
Maßstab
54,25 [2.136]
ISO
37,25 [1.467]
Connector M12
Allgemeintoleranzen
+0,1
+0,2
-0,1
-0,2
Nicht bemaßte
Werkstückkanten
DIN 6784
ASM GmbH
Am Bleichbach 18-22
D-85452 Moosinning
Tel.: 08123/986-0
Zeichnungsnummer / Datei
121404_PCQA24-ML(100-5750)-M12_003_LMZ.idw
Name
5/16
© ASM GmbH
[email protected]
Blatt
1
A4
POSICHRON®
38,3 [1.506]
39,1 [1.54]
28,3 [1.11]
58 [2.283]
end position
PCMAG3
start position
PCMAG3
64,5 [2.539]
26,3 [1.03]
With magnet PCMAG3
19,8 [0.78]
PCQA24
Square Profile Housing
46 [1.811]
58 [2.283]
total length A = measurement length + 155 [6.102] (e.g. 255[10.041])
35,5 [1.398]
PCQA-BFS1
mounting set
28,3 [1.11]
15,95 [0.628]
70 [2.757]
85 [3.348]
measurement length (e.g. 100 [3.937])
Dimensions in mm [inch]
Dimensions informative only. For guaranteed dimensions consult factory.
Zeichnung ist Eigentum der Firma ASM, Vervielfältigung nur mit Genehmigung
Schutzvermerk nach DIN 34 beachten © Copyright by ASM GmbH
Nicht bemaßte
Werkstückkanten
DIN 6784
Allgemeintoleranzen
+0,1
+0,2
-0,1
-0,2
ISO
2768-mH
Gezeichnet
Datum
22.04.2008
Maßstab
1:1
Name
waneck
Kontrolliert
dimensions in mm [inch]
DB-PCQA24-E-2013-11
www.asm-sensor.com
AUTOMATION
SENSORIK
MESSTECHNIK
Status
Änderungen
6/16
Datum
CT:
Werkstoff, Halbzeug
Benennung
PCQA24 + Zubehör
general drawing
Norm
AS M
BMC:
ASM GmbH
Am Bleichbach 18-22
D-85452 Moosinning
Tel.: 08123/986-0
Zeichnungsnummer / Datei
121404_PCQA24-(100-5750)-M12-PCQA
BFS1+PCMAG3_002_AMZ.idw
Name
© ASM GmbH
[email protected]
Blatt
1
A4
POSICHRON®
PCQA
Mounting Sets
Mounting set
PCQA-BFS1 with
mounting clamps
Isolation
sleeve
46
Isolation strip
Mounting clamp P
58
Note: The option -BFW can only be ordered with a new sensor, not separately!
Applicable for sensor lengths up to 1000 mm.
26,6 [1.047]
44 [1.732]
2 [.079]
24,65 [.97]
Ø25 [.984]
26,5 [1.043]
Option -BFW
Mounting brackets
for PCQA22 and
PCQA24
55 [2.165]
5 [.197]
42,5 [1.673]
4x R2,75 [.108]
5 [.197]
17,5 [.689]
35 [1.378]
20 [.787]
25 [.984]
Dimensions informative only.
For guaranteed dimensions consult factory.
Dimensions in mm [inch]
Order example: PCQA24 - 1000 - U2 - P1A - L10 - M12 - BFW
DB-PCQA24-E-2013-11
www.asm-sensor.com
7/16
© ASM GmbH
[email protected]
39 [1.535]
26 [1.024]
54,25 [2.136]
PCQA 10,2 [0.402]
Mounting Sets - Magnets
PCMAG5
Standard magnet
46 [1.811]
Gesamtlänge A = Messlänge + 155 [6.102] (z.B. 255 [10.041])
58 [2.283]
35,5 [1.398]
Befestigungssatz PCQA-BFS1
Messlänge (z.B. 100 [3.937])
± 12 [0.472]

M5
9,6 [0.378]
PCMAG3
Guided magnet
slider with internal
position magnet
70 [2.763]
26 [1.012]
85 [3.346]
59,25 [2.333]
Endposition
PCMAG5
2 ± 1 [0.079 ± 0.039]
®
37,25 [1.467]
POSICHRON
Anfangsposition
PCMAG5
39 [1.535]
28,25 [1.112]
Internal magnet
16 [0.630]
Mit eingesetztem Magnet
78 [3.071]
Dimensions informative only.
For guaranteed dimensions consult factory.
Dimensions in mm [inch]
DB-PCQA24-E-2013-11
www.asm-sensor.com
8/16
© ASM GmbH
[email protected]
POSICHRON®
Output Specification U2, U8 and I1
Configurable, 1 or 2 channels
U1, U2, U8
Voltage output
U1: 18 ... 36 V DC; U2: 18 ... 36 V DC; U8: 10 ... 36 V
Typ. 35 mA, 80 mA max.
U1: 0 ... 10 V DC; U2: 0.5 ... 10 V DC; U8: 0.5 ... 4.5 V DC
2 mA max.
> 5 kΩ
16 bit f.s., min. 10 µm
±50 x 10-6 / °C f.s.
Reverse polarity, short circuit
0.5 mVRMS
-40 ... +85 °C
EN 61326-1:2013
Excitation voltage
Excitation current
Output voltage
Output current
Output load
Resolution
Stability (temperature)
Protection
Output noise
Operating temperature
EMC
Signal diagram
Excitation +
Excitation GND
U1,
U2,
U8
Signal 1 +
Signal GND
Signal 2 + (as option)
SPAN/ZERO (PMU, as option)
Signal
diagram
I1
Current output (3 wire)
Excitation voltage
18 ... 36 V DC (10 ... 36 V for RL≤250Ω)
Excitation current
Load resistor
Output current
Resolution
Stability (temperature)
Protection
Output noise
Operating temperature
EMC
Typ. 60 mA, 80 mA max.
350 Ω max.
4 ... 20 mA, 30 mA max (at failure)
16 bit f.s., min. 10 µm
±50 x 10-6 / °C f.s.
Reverse polarity, short circuit
0.5 mVRMS
-40 ... +85 °C
EN 61326-1:2013
Excitation +
Signal diagram
Excitation GND
Signal 1 +
I1
Signal GND
Signal 2 + (as option)
SPAN/ZERO (PMU, as option)
DB-PCQA24-E-2013-11
www.asm-sensor.com
9/16
© ASM GmbH
[email protected]
POSICHRON®
Output Specification U2, U8 and I1
Configurable, 1 or 2 channels
Connector M12, 8-pin
Signal wiring
Signal
Cable connection
Plug connection
Excitation +
1
white
Excitation GND
2
brown
Signal 1 +
3
green
Signal GND
4
yellow
Signal 2 + (optional*)
5
grey
SPAN/ZERO (PMU** only, optional)
6
pink
View to the
sensor connector
* When using multiple magnets the distance between two magnets must be min. 70 mm to identify the
single magnets definitely.
** Description page 11
Connector M12, 5-pin
Signal wiring
Signal
Plug connection
Excitation +
1
Signal 1 +
2
GND
3
Signal 2 + (optional*)
4
PMU** (optional)
5
View to the
sensor connector
* When using multiple magnets the distance between two magnets must be min. 70 mm to identify the
single magnets definitely.
** Description page 11
Connector M8, 4-pin
Signal wiring
Signal
Plug connection
Excitation +
1
Excitation GND
2
Signal +
3
PMU** (optional)
4
View to the
sensor connector
* When using multiple magnets the distance between two magnets must be min. 70 mm to identify the
single magnets definitely.
** Description page 11
DB-PCQA24-E-2013-11
www.asm-sensor.com
10/16
© ASM GmbH
[email protected]
POSICHRON®
Description of Output Options
Option - PMU for
analog output
U1, U2, U8 and I1
Programming of the start and end value by the customer:
Diagnostic on analog
outputs
Behaviour of the analog signal output in case of error
The option PMU allows to program the start value and the end value of the output range
by a programming signal SPAN/ZERO available at the connector. This Signal SPAN/ZERO
must be connected with GND via a push button, then position magnet of the ­sensor must
be moved to the start resp. end position. Pushing the button between 2 and 4 seconds sets
the actual position as start position, pushing the button more than 5 seconds sets the actual
position as end position. The values will be stored and are available after switching off the
sensor.
To reset the sensor to the factory values the button must be pushed for longer than two
seconds when the sensor is switched on.
In case of error (magnet missing or outside the measuring range) the analog output signal
will assume a state ­according to the following options:
Alarm_HIGH
The output voltage resp. the output current is at HIGH level (overrange).
Alarm_LOW
The output voltage resp. the output current is at LOW level (underrange).
Alarm_HOLD
The output voltage resp. the output current will keep the last valid state.
Error signal for
SSI output
DB-PCQA24-E-2013-11
www.asm-sensor.com
Alarm_HIGH
(standard)
Alarm_LOW
(.../U)
Alarm_HOLD
(.../H)
U1
Uout ≥ 10,5 V
—
keeps last valid state
(Order code U1/H)
U2
Uout ≥ 10,5 V
Uout < 0,25 V
(Order code U2/U)
keeps last valid state
(Order code U2/H)
U8
Uout ≥ 10 V
Uout < 0,25 V
(Order code U8/U)
keeps last valid state
(Order code U8/H)
I1
Iout ≥ 21 mA
1,5 ... 2 mA
keeps last valid state
(Order code I1/H)
(Order code I1/U)
If the sensor cannot detect a magnet the position value will assume the maximum value
(0xFFFFFFF).
11/16
© ASM GmbH
[email protected]
POSICHRON®
Output Specification SSI
Synchronous serial
interface SSI
Description
Output
Excitation voltage
Excitation current
Clock frequency
Code
Resolution
Delay between pulse trains
Stability (temperature)
Operating temperature
EMC
RS422
10 ... 36 V DC, residual ripple 10 mVSS
Typ. 80 mA, 150 mA max.
100 kHz ... 1 MHz
Gray code, dual code
≥ 5 µm
>25 µs
±50 x 10-6 / °C f.s.
-40 ... +85 °C
EN 61326-1:2013
The data transmission takes place by means of the two signals CLOCK and DATA. The processing unit (PLC, microcomputer) sends pulse sequences which clock the data transmission at the required transfer rate. With the first falling edge of the pulse sequence the position
of the sensor is recorded and stored. The following rising edges control the bit-by-bit transfer
of the data word. After a delay time the next new position information can be transwithted.
Data format
(Train of 26 pulses)
Signal diagram
Sensor circuit
Subsequent circuit
DATA
DATA
CLOCK
CLOCK
Cable length
50 m
100 m
Signal wiring
Signal
Baud rate
100-1000 kHz
100-300 kHz
Plug connection
Note:
Extension of the cable length will reduce the
­maximum transmission rate.
The signals CLOCK/CLOCK and DATA/DATA
must be connected in a twisted pair cable,
­common shielded.
Cable connection
Excitation +
1
white
Excitation GND
2
brown
CLOCK
3
green
CLOCK
4
yellow
DATA
5
grey
DATA
6
pink
View to sensor
connector
Error indication see page 11.
DB-PCQA24-E-2013-11
www.asm-sensor.com
12/16
© ASM GmbH
[email protected]
POSICHRON®
Output Specification CANopen
Description
Interface CANOP
­ ANopen interface with process data for position and cam functions, programmable are
C
preset, resolution, filtering and cam switching points.
Communication profile
Encoder profile
Error Control
Node ID
PDO
PDO Modes
Nodes
Bus connection
Integrated bus terminating resistor
Bus, galvanic isolated
CANopen CiA 301 V 4.02, Slave
Encoder CiA 406 V 3.2
Node Guarding, Heartbeat, Emergency Message
Adjustable via LSS or via object dictionary
4 TxPDO, 0 RxPDO, no linking, static mapping
Event-/Time triggered, Remote-request, Sync
cyclic/acyclic
1 server, 0 client
8 cams
Yes
50 kBaud to 1 MBaud, adjustable via LSS or via
object dictionary
127 max.
M12 connector, 5 pins
120 Ω (option)
No
Excitation voltage
Excitation current
Number of position magnets
Resolution
Measuring rate
Stability (temperature)
Repeatability
Operating temperature
Protection
Dielectric strength
EMC
18 ... 36 V DC
Typ. 20 mA for 24 V, max. 80 mA
1 ... 4
50 µm
1 kHz (asynchronous)
±50 x 10-6 / °C f.s.
1 LSB
-40 ... +85 °C
Reverse polarity, short circuit
500 V (V AC, 50 Hz, 1 min.)
EN 61326-1:2013
SDO
CAM
Certified
Transmission rates
Specifications
When using multiple magnets the distance between two magnets must be min. 70 mm to
identify the single magnets definitely.
Signal wiring
DB-PCQA24-E-2013-11
www.asm-sensor.com
Signal
Plug connection
Shield
Excitation +
GND
CAN-H
CAN-L
View to sensor connector
1
2
3
4
5
13/16
© ASM GmbH
[email protected]
POSICHRON®
Output Specification CAN SAE J1939
Interface J1939
NAME Fields
Parameter Group
Numbers (PGN)
Specifications
CAN specification
Transceiver
Communication profile
Baud rate
Internal temination resistor
Address
ISO 11898, Basic and Full CAN 2.0 B
24V-compliant, not isolated
SAE J1939
250 kbit/s
120 Ω (option)
Default 247d, configurable
Arbitrary address capable
Industry group
Vehicle system
Vehicle system instance
Function
Function instance
ECU instance
Manufacturer
Identity number
0
0
7Fh (127d)
0
FFh (255d)
0
0
145h (325d)
0nnn
Configuration data
PGN EF00h
Process data
PGN FFnnh
Excitation voltage
Excitation current
Measuring rate
Stability (temperature)
Repeatability
Operating temperature
Protection
Dielectric strength
EMC
18 ... 36 V DC
Typ. 20 mA for 24 V, max. 80 mA
1 kHz (asynchronous)
±50 x 10-6 / °C f.s.
1 LSB
-40 ... +85 °C
Reverse polarity, short circuit
500 V (V AC, 50 Hz, 1 min.)
EN 61326-1:2013
No
Global
Non specific
Non specific
Manufacturer ID
Serial number 21 bit
Proprietary-A
(PDU1 peer-to-peer)
Proprietary-B
(PDU2 broadcast);
nn Group Extension (PS)
configurable
When using multiple magnets the distance between two magnets must be min. 70 mm to
identify the single magnets definitely.
Signal wiring
DB-PCQA24-E-2013-11
www.asm-sensor.com
Signal
Plug connection
Shield
Excitation +
GND
CAN-H
CAN-L
View to sensor connector
1
2
3
4
5
14/16
© ASM GmbH
[email protected]
POSICHRON®
Accessories
Connector Cables
Connector cable
M12, 5-pin
shielded
The 5-lead shielded cable is supplied with a
mating 5-pin 90° M12 connector at one end and
5 wires at the other end. Available lengths are
2 m, 5 m and 10 m. Wire: cross sectional area
0.34 mm2.
Order code:
KAB - XM - M12/5F/W - LITZE
IP69K: KAB - XM - M12/5F/W/69K - LITZE
Length in m
Connector cable
M12, 5-pin
shielded
The 5-lead shielded cable is supplied with a
mating 5-pin M12 connector at one end and 5
wires at the other end. Available lengths are 2
m, 5 m and 10 m. Wire: cross sectional area
0.34 mm2.
Order code:
KAB - XM - M12/5F/G - LITZE
IP69K:
KAB - XM - M12/5F/G/69K - LITZE
Length in m
Signal wiring
M12, 5-pin
Connector cable
M12, 8-pin
shielded
Plug connection / Cable connection
1
brown
2
white
3
blue
4
black
5
grey
The 8-lead shielded cable is supplied with a
mating 8-pin 90° M12 connector at one end
and 8 wires at the other end. Available lengths
are 2, 5 and 10 m. Wire: cross sectional area
0.25 mm².
Order code:
KAB - XM - M12/8F/W - LITZE
IP69K: KAB - XM - M12/8F/W/69K - LITZE
Length in m
Connector cable
M12, 8-pin
shielded
The 8-lead shielded cable is supplied with a
mating 8-pin M12 connector at one end and
8 wires at the other end. Available lengths
are 2, 5 and 10 m. Wire: cross sectional area
0.25 mm².
Order code:
KAB - XM - M12/8F/G - LITZE
IP69K: KAB - XM - M12/8F/G/69K - LITZE
Length in m
Signal wiring
M12, 8-pin
DB-PCQA24-E-2013-11
www.asm-sensor.com
Plug connection / Cable connection
1
white
2
brown
3
green
15/16
4
yellow
5
grey
6
pink
7
blue
8
red
© ASM GmbH
[email protected]
POSICHRON®
Accessories
Connector Cables
Connector/bus cable
M12, 5-pin
CAN bus
shielded
The 5-lead shielded cable is supplied with a
female 5-pin M12 connector at one end and
a male 5-pin M12 connector at the other end.
Available lengths are 0.3 m, 2 m, 5 m and
10 m.
Order code:
KAB - XM - M12/5F/G - M12/5M/G - CAN
IP69K: KAB - XM - M12/5F/G/69K - M12/5M/G/69K - CAN
Length in m
T-piece for bus cable
M12, 5-pin
CAN bus
Order code:
KAB - TCONN - M12/5M - 2M12/5F - CAN
Terminating
resistance
M12, 5-pin
CAN bus
DB-PCQA24-E-2013-11
www.asm-sensor.com
Order code:
KAB - RTERM - M12/5M/G - CAN
16/16
© ASM GmbH
[email protected]