Product Datasheet

AWC6340H
HELP CDMA Band Class 0,10
CDMA Power Amplifier Module
TM
DATA SHEET - Rev 2.1
FEATURES
• CDMA/EVDO Compliant
•HELPTM technology
• High Efficiency (RC-1 waveform):
AWC6340
H
• 36 % @ POUT = +28.0 dBm
• 17 % @ POUT = +15.5 dBm
• Low Quiescent Current: 13 mA
• Low Leakage Current in Shutdown Mode: <6 µA
• Internal Voltage Regulator
• Integrated “daisy chainable” directional coupler
with CPLIN and CPLOUT port.
• Internal DC Blocks on all RF ports
10 Pin 3 mm x 3 mm x 0.9 mm
Surface Mount Module
• Optimized for a 50 Ω System
• 1.8V Control Logic
• RoHS Compliant Package, 260 oC MSL-3
APPLICATIONS
• Band Class 0, 10 CDMA/EVDO Wireless
Devices
GND at Slug (pad)
PRODUCT DESCRIPTION
The AWC6340H is a HELP TM product for CDMA VBATT
devices operating in Band Class 0 and 10. This PA
incorporates ANADIGICS’ HELP™ technology to
deliver exceptional efficiency at low power levels and
RFIN
low quiescent current without the need for external
voltage regulators or converters. The device is
manufactured using advanced InGaP HBT technology
offering state-of-the-art reliability, temperature stability, GND
and ruggedness. Two selectable bias modes that
optimize efficiency for different output power levels and
a shutdown mode with low leakage current increase
VMODE
handset talk and standby time. A “daisy chainable”
directional coupler is integrated in the module thus
eliminating the need of an external coupler. The selfcontained 3 mm x 3 mm x 0.9 mm surface mount
VEN
package incorporates matching networks optimized for
output power, efficiency, and linearity in a 50 Ω system.
05/2013
1
10
2
VCC
9
RFOUT
8
CPLIN
4
7
GND
5
6
CPLOUT
3
CPL
Bias Control
Voltage Regulation
Figure 1: Block Diagram
AWC6340H
VBATT
1
10
RFIN
2
9
RFOUT
GND
3
8
CPLIN
VMODE
4
7
GND
VEN
5
6
CPLOUT
Figure 2: Pinout (X-ray Top View)
Table 1: Pin Description
2
PIN
NAME
DESCRIPTION
1
VBATT
Battery Voltage
2
RFIN
RF Input
3
GND
Ground
4
VMODE
Mode Control Voltage
5
VEN
6
CPLOUT
7
GND
Ground
8
CPLIN
Coupler Input
9
RFOUT
RF Output
10
VCC
PA Enable Voltage
Coupler Output
Supply Voltage
DATA SHEET - Rev 2.1
05/2013
VCC
AWC6340H
ELECTRICAL CHARACTERISTICS
Table 2: Absolute Minimum and Maximum Ratings
PARAMETER
MIN
MAX
UNIT
Supply Voltage (VCC)
0
+5
V
Battery Voltage (VBATT)
0
+6
V
Control Voltages (VMODE, VEN)
0
+3.5
V
RF Input Power (PIN)
-
+10
dBm
-40
+150
°C
Storage Temperature (TSTG)
Stresses in excess of the absolute ratings may cause permanent damage.
Functional operation is not implied under these conditions. Exposure to
absolute ratings for extended periods of time may adversely affect reliability.
Table 3: Operating Ranges
PARAMETER
MIN
TYP
MAX
UNIT
COMMENTS
Operating Frequency (f)
816
-
849
MHz
BC0, BC10
Supply Voltage (VCC)
+3.1
+3.4
+4.35
V
POUT ≤ +28 dBm
Enable Voltage (VEN)
+1.35
0
+1.8
-
+3.1
+0.5
V
PA "on"
PA "shut down"
Mode Control Voltage (VMODE)
+1.35
0
+1.8
-
+3.1
+0.5
V
Low Bias Mode
High Bias Mode
27.5(1)
26.9
-
28
27.7
15.5
-
dBm
-30
-
+90
C
CDMA Output Power
HPM
HPM
LPM
Case Temperature (TC)
BC0
CDMA 2000, RC1
BC10
The device may be operated safely over these conditions; however, parametric performance is guaranteed only
over the conditions defined in the electrical specifications.
Note:
(1) For operation at 3.1 V, POUT is derated by 0.8 dB.
3
DATA SHEET - Rev 2.1
05/2013
AWC6340H
Table 4: Electrical Specifications - CDMA2000 Operation BC0 (RC-1 waveform)
(TC = +25 °C, VBATT = VCC = +3.4 V, VENABLE = +1.8 V, 50 Ω system)
PARAMETER
MIN
TYP
MAX
UNIT
Gain
25.5
13.5
28
16
31
20
Adjacent Channel Power
at ±885 kHz offset (1)
Primary Channel BW = 1.23 MHZ
Adjacent Channel BW = 30 kHz
-
-49
-54
Adjacent Channel Power
at ±1.98 MHz offset (1)
Primary Channel BW = 1.23 MHZ
Adjacent Channel BW = 30 kHz
-
COMMENTS
POUT
VMODE
dB
+28 dBm
+15.5 dBm
0V
1.8 V
-46
-46
dBc
+28 dBm
+15.5 dBm
0V
1.8 V
-59
-61
-56.5
-56.5
dBc
+28 dBm
+15.5 dBm
0V
1.8 V
32
-
37
18
-
%
+28 dBm
+15.5 dBm
0V
1.8 V
Quiescent Current (Icq)
Low Bias Mode
-
13
20
mA
through VCC pin
1.8 V
Mode Control Current
-
0.06
0.15
mA
through VMODE pin, VMODE = 1.8 V
Enable Current
-
0.06
0.15
mA
through VEN pin, VMODE = 1.8 V
BATT Current
-
2.5
4.5
mA
through VBATT pin, VMODE = +1.8 V
Leakage Current
-
6
15
µA
VBATT = +4.35 V, VCC = +4.35 V,
VEN = 0 V, VMODE = 0 V
Noise in Receive Band
-
-134
-
dBm/Hz
Harmonic
2fo
3fo, 4fo
-
-40
-50
-
dBc
Coupling Factor
-
20
-
dB
Coupler IN_OUT
Daisy Chain Insertion Loss
-
<0.25
-
dB
698 MHz to 2620 MHz
Pin 8-6, Shutdown Mode
Efficiency (1)
Spurious Output Level
(all spurious outputs)
Load mismatch stress with no
permanent degradation or failure
-
-
-70
dBc
POUT ≤ +28 dBm
In-band Load VSWR < 5:1
Out-of-band Load VSWR < 10:1
Applies over all operating conditions
8:1
-
-
VSWR
Applies over all operating conditions
Notes:
(1) ACLR and Efficiency measured at 836.5 MHz.
4
POUT ≤ +28 dBm
DATA SHEET - Rev 2.1
05/2013
AWC6340H
APPLICATION INFORMATION
To ensure proper performance, refer to all related
Application Notes on the ANADIGICS web site:
http://www.anadigics.com
Shutdown Mode
The power amplifier may be placed in a shutdown
mode by applying logic low levels (see Operating
Ranges table) to the VEN and VMODE voltages.
The Bias Control table below lists the recommended
modes of operation for various applications.
Two operating modes are recommended to optimize
current consumption. HighBias/High Power operating
mode is for Pout levels >16 dBm. At about 16 dBm, the
PA should be “Mode Switched” to Low Power Mode.
Bias Modes
The power amplifier may be placed in either Low or
High Bias modes by applying the appropriate logic
level (see Operating Ranges table) to the VMODE pin.
Vcontrols
Venable/Vmode(s)
On Sequence Start
T_0N = 0µ
Rise/Fall Max 1µS
Defined at 10% to 90%
of Min/Max Voltage
Off Sequence Start
T_0FF = 0µ
ON Sequence
OFF Sequence
RFIN
notes 1,2
VEN
VCC
note 1
T_0N+1µS
T_0N+3µS
T_0FF+2µS T_0FF+3µS
Referenced After 90% of Rise
Time
Referenced Before10% of Fall
Time
Figure 3: Recommended ON/OFF Timing Sequence
Notes:
(1) Level might be changed after RF is ON.
(2) RF OFF defined as PIN ≤ -30 dBm.
(3) Switching simultaneously between VMODE and VEN is not recommended.
Table 5: Bias Control
POUT
LEVELS
BIAS
MODE
VEN
VMODE
VCC
VBATT
Low power
≤ +16 dBm
Low
+1.8 V
+1.8 V
3.1 - 4.35 V
> 3.1 V
High power
> +16 dBm
High
+1.8 V
0V
3.1 - 4.35 V
> 3.1 V
-
Shutdown
0V
0V
3.1 - 4.35 V
> 3.1 V
APPLICATION
Shutdown
5
DATA SHEET - Rev 2.1
05/2013
AWC6340H
VBATT
VCC
C2
2.2 µF
C1
33 pF
GND at slug
1
2
RFIN
VMODE1
VCC
RFIN
RFOUT
10
9
GND
CPLIN
8
4
VMODE
GND
7
5
VEN
3
VEN
VBATT
CPLOUT 6
Figure 4: Evaluation Board Schematic
6
DATA SHEET - Rev 2.1
05/2013
C3
330 pF
C5
C4
0.01 µF 2.2 µF ceramic
RFOUT
CPLIN
CPLOUT
AWC6340H
PACKAGE OUTLINE
Figure 5: Package Outline - 10 Pin 3 mm x 3 mm x 0.9 mm Surface Mount Module
Pin 1 Identifier
Date Code (YYWW)
6340H
LLLLNN
YYWWCC
Part Number
Lot Number
Country Code(CC)
Figure 6: Branding Specification - M45 Package
7
DATA SHEET - Rev 2.1
05/2013
AWC6340H
PCB AND STENCIL DESIGN GUIDELINE
Figure 7: Recommended PCB Layout Information
8
DATA SHEET - Rev 2.1
05/2013
AWC6340H
COMPONENT PACKAGING
Pin 1
Figure 8: Carrier Tape
Figure 9: Reel
9
DATA SHEET - Rev 2.1
05/2013
AWC6340H
ORDERING INFORMATION
ORDER NUMBER
TEMPERATURE
RANGE
PACKAGE
DESCRIPTION
COMPONENT PACKAGING
AWC6340HQ7
-30 oC to +90 oC
RoHS Compliant 10 Pin
3 mm x 3 mm x 0.9 mm
Surface Mount Module
Tape and Reel, 2500 pieces per Reel
AWC6340HP9
-30 oC to +90 oC
RoHS Compliant 10 Pin
3 mm x 3 mm x 0.9 mm Partial Tape and Reel
Surface Mount Module
ANADIGICS
141 Mount Bethel Road
Warren, New Jersey 07059, U.S.A.
Tel: +1 (908) 668-5000
Fax: +1 (908) 668-5132
URL: http://www.anadigics.com
IMPORTANT NOTICE
ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice.
The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to
change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed
to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers
to verify that the information they are using is current before placing orders.
warning
ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product
in any such application without written consent is prohibited.
10
DATA SHEET - Rev 2.1
05/2013