Hybrid Couplers 3dB, 90º Type PC2025A2100AT00 GENERAL DESCRIPTION The PC2025A2100AT00 is a RoHS compliant low profile wideband 3dB hybrid coupler which can support mobile applications, including PCS and DCS applications. The power coupler series of components is based on AVX’s patented MLO™ technology (US patents 6,987309, 7,068,124) which incorporates lumped elements and micro vias. The resultant designs and finished structures allow for the integration of high Q passives in a low cost high density interconnect component. The PC2025A2100AT00 is a multifunctional component designed for attenuators, phase shifters, LNAs, balance amplifiers and signal distribution. All components are electrically tested prior to tape and reel. Reliability testing is performed to JEDEC and Mil standards. Finishes are available in RoHS compliant NiSn and immersion Au. FEATURES APPLICATIONS • 1.5 – 2.1 GHz • Excellent Isolation • DCS and PCS • Expansion Matched to PCB • 90º Quadrature • Surface Mountable • RoHS Compliant • Available in Tape and Reel • • • • Mobile communications GPS Vehicle location systems Wireless LAN’s LAND GRID ARRAY ADVANTAGES • • • • TOP VIEW Inherent Low Profile Excellent Solderability Low Parasitics Better Heat Dissipation mm (inches) L W T HOW TO ORDER PC 2025 A 2100 A T 00 1 Series Size Type Frequency (MHz) Standard Testing Termination 7 = Au T = NiSn Product Code 00 = Standard Product Packaging Code 1 = Bulk 2 = 500 pcs, 7" reel 4 = 2000 pcs, 13" reel 6.35 (0.25) 5.08 (0.20) 1.0 (0.04) ELECTRICAL SPECIFICATIONS* Frequency (GHz) Isolation (dB min) I. L. (dB max) VSWR 1.5 – 2.1 18 0.25 1.25 Amplitude Balance (dB max) ±0.45 Phase Balance (Degrees) ±3º Max Power (Watts) 30 Operating Temperature (ºC) -55 to +85 * Specification based on performance of component assembled properly on printed circuit board with 50Ω nominal impedance. QUALITY INSPECTION TERMINATION Finished parts are 100% tested for electrical parameters and visual characteristics. Finishes include NiSn, and immersion Au. All finishes compatible with automatic soldering technologies: Pb free reflow, wave soldering, vapor phase and manual. OPERATING TEMPERATURE - 55ºC to +85ºC 1 Hybrid Couplers 3dB, 90º Type PC2025A2100AT00 MECHANICAL OUTLINE TOP VIEW (Near-side) BOTTOM VIEW (Far-side) 6.35 ± 0.25 (0.250 ± 0.010) 0.46 ±0.10 (0.018 ± 0.004) Pin 1 3.56 ± 0.10 (0.140 ± 0.004) Pin 2 Pin 2 5.08 ± 0.25 (0.200 ± 0.010) Pin 4 Pin 1 3.08 ± 0.10 (0.123 ± 0.004) Pin 3 Pin 3 Pin 4 4.35 ± 0.10 (0.172 ± 0.004) SIDE VIEW 1.00 ± 0.27 (0.039 ± 0.011) Dimensions mm (inches) Tolerances are Non-Cumulative 2 1.0 ±0.10 (0.040 ± 0.004) Hybrid Couplers 3dB, 90º Type PC2025A2100AT00 TYPICAL PERFORMANCE: 1.5 TO 2.1 GHZ Insertion Loss Coupling Amplitude Balance Phase Balance Return Loss Isolation 3 Hybrid Couplers 3dB, 90º Type PC2025A2100AT00 HYBRID COUPLER TEST JIGS GENERAL DESCRIPTION These jigs are designed for testing the 3dB Hybrid Couplers using a Vector Network Analyzer. They consist of a dielectric substrate, having Cu microstrips as conducting lines and a bottom ground plane located at a distance of 0.254mm from the microstrips. The substrate used is Taconic RF 35 0100. The connectors are SMA type (female), ‘Johnson Components Inc.’ Product PIN: l42-070l-84l. Both a measurement jig and a calibration jig are provided. The calibration jig is designed for a full 2port calibration, and consists of an open line, short line and through line. LOAD calibration can be done by a 502 SMA termination. MOUNTING AND MEASUREMENT PROCEDURE PIN CONFIGURATION MLO™ hybrid couplers require a 50Ω transmission lines leading to and from all of the RF ports. Proper grounding is required in order to ensure optimal device performance. All of the MLO™ components utilize castellated interconnects which allow for high yield assembly, expansion matched and halogen free dielectrics. The MLO™ hybrid coupler is a symmetrical device. When a port is designated as the input, automatically the two output and isolated ports are defined. For example, if the input port for a device was selected to be Pin 1, Pin 2 is automatically the isolated port, Pin 4 is the 0 degree reference output port, and Pin 3 is the output port which “lags” behind the reference output port by 90 degrees. Similarly, if Pin 3 was to be selected as the input port, the adjacent port on the long side (Pin 4) is the isolated port, the adjacent port on the short side (Pin 2) is the 0 degree output port, and the opposite port (Pin 1) is the 90 degree output port. The PC2025A2100 part has an orientation marker to denote Pin 1. Once port one is determined the other ports are As defined; See the chart below for clarification: 1 4 Configuration Splitter Splitter Splitter Splitter *Combiner *Combiner *Combiner *Combiner 2 3 Pin 1 Pin 2 Pin 3 Pin 4 Input Isolated -3dB ∠-90 -3dB ∠ Isolated Input -3dB ∠ -3dB ∠-90 -3dB ∠-90 -3dB ∠ Input Isolated -3dB ∠ -3dB ∠-90 Isolated Input A ∠-90 A ∠ Isolated Output A ∠ A ∠-90 Output Isolated Isolated Output A ∠-90 A ∠ Output Isolated A ∠ A ∠-90 *Note: “A” is the amplitude of the applied signals. When two quadrature signals with equal amplitudes are applied to the coupler as described they will combine at the output port. MEASUREMENT PROCEDURE Measurement Jig Connector 1 Connector 2 Connector 4 Connector 3 4 Calibration Jig Hybrid Couplers 3dB, 90º Type PC2025A2100AT00 AUTOMATED SMT ASSEMBLY surface mount assembly of MLO TM RF devices onto the PCB. Stencil thickness and aperture openings should be adjusted according to the optimal solder volume. The following are general recommendations for SMT mounting of MLOTM devices onto the PCB. The following section describes the guidelines for automated SMT assembly of MLOTM RF devices which are typically Land Grid Array (LGA) packages or side termination SMT packages. Control of solder and solder paste volume is critical for SMT REFLOW PROFILE and slower preheating time may be required to improve the out-gassing of solder paste. In addition, the reflow profile depends on the PCB density and the type of solder paste used. Standard no-clean solder paste is generally recommended. If another type of flux is used, complete removal of flux residual may be necessary. Example of a typical lead free reflow profile is shown below: Common IR or convection reflow SMT processes shall be used for the assembly. Standard SMT reflow profiles, for eutectic and Pb free solders, can be used to surface mount the MLO TM devices onto the PCB. In all cases, a temperature gradient of 3°C/sec, or less, should be maintained to prevent warpage of the package and to ensure that all joints reflow properly. Additional soak time tp Tp Critical Zone TL to Tp Ramp-up Temperature TL tL Ts max Ts min Ramp-down ts Preheat 25 t 25ºC to Peak Time Profile Parameter Ramp-up rate (Tsmax to Tp) Preheat temperature (Ts min to Ts max) Preheat time (ts) Time above TL, 217ºC (tL) Peak temperature (Tp) Time within 5ºC of peak temperature (tp) Ramp-down rate Time 25ºC to peak temperature Pb free, Convection, IR/Convection 3ºC/second max. 150ºC to 200ºC 60 – 180 seconds 60 – 120 seconds 260°C 10 – 20 seconds 4ºC/second max. 6 minutes max. 5 Hybrid Couplers 3dB, 90º Type PC2025A2100AT00 RECOMMENDED PAD LAYOUT To ensure proper electrical and thermal performance there must be gound plane with 100% solder connection underneath the part PC2100 4.42 (0.174) Multiple plated thru holes to ground 0.61 (0.024) 0.61 (0.024) 3.15 (0.124) 1.14 SQ (0.045) 2.51 (0.099) 50Ω Transmission Line Dimensions are in mm (inches) 6