FT232BM Designers Guide

FT232BM Designers Guide
FT232BM Designers Guide
Version 2.0
Introduction
Welcome to the FT232BM Designer’s Guide. The Designers Guide includes printouts of a number of FT232BM
reference schematics and explanations of the key points of each schematic. These are intended to be used in
conjunction with the FT232BM data sheet, the current version of which should also be downloaded from the
FTDI web site.
The schematic files are downloadable separately as a ZIP archive which contains the schematics both in
OrCAD SDT 16-bit DOS format and in OrCAD Capture for Windows 32-bit format.
The OrCAD SDT 16-bit DOS format schematics are readable by OrCAD SDT version 3.2 and above. These
consist of files with the following extensions –
• .sch = OrCAD 16-bit DOS binary schematic file
• .lib = OrCAD 16-bit DOS binary component library file
• .src = OrCAD DOS library source ( text ) file
The OrCAD Capture for Windows schematics are readable by OrCAD Capture version 7.2 and above. These
consist of a file with a .dsn extension.
Notes for Protel users
OrCAD 16-bit DOS schematics can be imported into Protel schematic capture for Windows. Before reading in
the schematic ( .sch ) file, create a Protel library first by reading in the OrCAD library source ( .src ) file and
save it in Protel binary library format. Both OrCAD and Protel use the same default extensions for schematic
and library files, so if you do not wish to overwrite the original OrCAD files, save the Protel versions to a
different folder.
DG232 Version 2.0
© Future Technology Devices Intl. Ltd. 2002/2003
Page 1 of 16
DG232 Version 2.0
CN1
CN-USB
5
C3
10uF
VCC
© Future Technology Devices Intl. Ltd. 2002/2003
Page 2 of 16
2
27R
27R
R4
R5
C1
0.1uF
Y1
6MHz RESONATOR
RSTOUT#
C5
10nF
VCC
R6
VCC
C4
33nF
R2
2k2
1k5
VCC
31
2
1
32
4
28
27
5
7
8
6
C6
0.1uF
R3
470R
CS
SK
DIN
DOUT
U2
VCC
NC
NC
GND
10k
R1
93C46/56/66
( Optional )
1
2
3
4
8
7
6
5
SLEEP#
RXLED#
TXLED#
PWRCTL
PWREN#
TXDEN
RI#
DCD#
DSR#
DTR#
CTS#
RTS#
RXD
TXD
VCC
FT232BM
10
11
12
14
15
16
18
19
20
21
22
SLEEP#
RSTOUT#
R7
47k
VCC-5v
VCC
RESET#
POWERDN#
GND
5v MCU or Logic cct
CTS#
RTS#
RXD
24
23
TXD
25
U1
FT232B APPLICATION SCHEMATIC
TEST
EEDATA
EESK
EECS
RESET#
XTOUT
XTIN
RSTOUT#
USBDP
USBDM
3V3OUT
VCC
INTERFACING TO 5 V LOGIC - BUS POWERED ( <= 100mA ) APPLICATION
C2
0.1uF
DECOUPLING CAPS
1
2
3
4
FB1
FERRITE BEAD
1
30
AVCC
AGND
29
3
26
13
VCC
VCC
VCC-IO
GND
GND
C7
0.1uF
Figure 1.0
9
17
USB
FT232BM Designers Guide
FT232BM – 5 volt Bus Powered Example Schematic ( 232-5VB )
FT232BM Designers Guide
Figure 1.0 is an example of a 5 volt, USB bus powered design using the FT232BM connected to a 5v MCU or
other external logic.
• In this example, we assume that the total current of the design is <= 100mA ( low power ), and that the
MCU / logic can detect USB suspend mode using either the SLEEP# or PWREN# pins of the FT232BM and
put itself and any circuitry it is controlling into a low power state in order to meet the total USB suspend
current requirement of 500uA or less.
• RSTOUT# is used to provide a power-on reset to the external logic in this example. If the MCU has it’s
own power-on reset logic then there is usually no need to use RSTOUT# to reset the device and this
connection and the 47k pull-down can be omitted.
• PWRCTL is tied to GND to tell the device to indicate a bus powered device in it’s USB descriptor.
• RTS / CTS handshaking is used in this example. If the MCU has no dedicated handshaking signals then
general purpose IO pins can usually be used to implement the handshaking. If the MCU is guaranteed to
accept data sent from the FT232BM at the programmed baud rate, then a single wire handshake will do (
tie CTS# of the FT232BM to GND ).
General Design Notes:
•
•
•
•
•
SLEEP# goes inactive ( high ) at power-on and goes low during USB suspend. PWREN# is high on
power-on and only goes low ( active ) after the device has been configured ( successfully enumerated )
by USB. During USB suspend PWREN# will go high – the opposite polarity to SLEEP#. For a low power
bus powered USB device , either SLEEP# or PWREN# can be used for power control, however for a high
power bus powered USB device ( 100mA .. 500mA ) you must use PWREN# for power control as no USB
device is allowed to draw more than 100mA from the bus until USB configuration is complete.
RSTOUT# has no pull-down capability – it drives to 3.3v when not in reset, and goes tri-state during
power-on reset. If used to reset an external device, a pull-down resistor must be added to make it low
during reset.
When RTS/CTS hardware handshaking is enabled CTS# can be used to stop the FT232BM transmitting
data to the MCU / external logic. When CTS# is active ( low ) the FT232BM will transmit any data in it’s
internal buffers. On taking CTS# high, the FT232BM will stop transmitting data. Due to the asynchronous
nature of the interface, there is a latency of 0 to 3 characters between taking CTS# high and data
transmission stopping. The FT232BM drives RTS# high when the available buffer space inside the device
drops below 32 bytes. This allows the MCU / logic to continue to send up to 30 characters to the FT232BM
after RTS# goes high without causing buffer over-run.
A suitable 3-pin ceramic resonator could be a Murata CSTCR6M00G15 or equivalent. See http://
www.murata.com/catalog/p63e.pdf for details If you prefer to use a 2 pin resonator or a crystal refer to
Figures 4 and 5 of the FT232BM data sheet for details.
A suitable ferrite bead could be a Steward MI0805K400R-00 or equivalent. This is also available from
DigiKey as Part # 240-1035-1. For specifications consult the Steward web site - http://www.steward.com
DG232 Version 2.0
© Future Technology Devices Intl. Ltd. 2002/2003
Page 3 of 16
DG232 Version 2.0
5
CN1
CN-USB
R8
15k
R6
10k
C3
10uF
VCC
C2
0.1uF
DECOUPLING CAPS
1
2
3
4
27R
R5
© Future Technology Devices Intl. Ltd. 2002/2003
Page 4 of 16
Y1
6MHz RESONATOR
C4
33nF
R2
2k2
31
2
1
32
4
28
27
5
7
8
6
C5
0.1uF
R3
470R
CS
SK
DIN
DOUT
U2
VCC
NC
NC
GND
10k
R1
93C46/56/66
( Optional )
1
2
3
4
8
7
6
5
SLEEP#
RXLED#
TXLED#
PWRCTL
PWREN#
TXDEN
RI#
DCD#
DSR#
DTR#
CTS#
RTS#
RXD
TXD
VCC
FT232BM
10
11
12
14
15
16
18
19
20
21
22
VCC
SLEEP#
UPDATED 21st January 2003
VCC-5v
VCC
VCC
POWERDN#
GND
5v MCU or Logic cct
CTS#
RTS#
RXD
24
23
TXD
25
U1
FT232B APPLICATION SCHEMATIC
TEST
EEDATA
EESK
EECS
RESET#
XTOUT
XTIN
RSTOUT#
USBDP
USBDM
3V3OUT
VCC
INTERFACING TO 5 V LOGIC - SELF POWERED APPLICATION
C1
0.1uF
R7
1k5
27R
R4
VCC
30
AVCC
AGND
29
3
26
13
VCC
VCC
VCC-IO
GND
GND
GND
EXTERNAL 5V POWER
VCC
C6
0.1uF
Figure 2.0
9
17
USB
FT232BM Designers Guide
FT232BM – 5 volt Self Powered Example Schematic ( 232-5VS )
FT232BM Designers Guide
Figure 2.0 is an example of a 5 volt, USB self powered design using the FT232BM connected to a 5v MCU or
other external logic. A USB self power design has it’s own PSU and does not draw it’s power from the USB
bus. In such a case, no special care need be taken to meet the USB suspend current ( 0.5mA ) as the device
does not get its power from the USB port.
• In this case it is still useful to connect SLEEP# ( or PWREN# ) to the CPU as this will let the CPU know
that the PC is in suspend mode and thus unable to communicate with the device. If the device requires to
“wake up” the PC then the MCU should connect one of it’s IO Ports to the Ring Indicator pin ( RI# ). The
default state of RI# should be high - strobing this low for a few milliseconds then taking it high again will
cause a USB resume sequence thus requesting the PC to wake up. To use this feature, Remote Wake-Up
must be enabled in the 93C46 EEPROM.
• PWRCTL is tied to VCC to tell the device to indicate a self powered device in it’s USB descriptor.
• RTS / CTS handshaking is used in this example. If the MCU has no dedicated handshaking signals then
general purpose IO pins can usually be used to implement the handshaking. If the MCU is guaranteed to
accept data sent from the FT232BM at the programmed baud rate, then a single wire handshake will do (
tie CTS# of the FT232BM to GND ).
• Self powered designs should NOT force current back into the Host PC ( or HUB ) via the USB Port when
the said Host / Hub is powered down and the self powered device is still powered-up from it’s own
PSU. This rule includes injecting current into the powered down Host / Hub via the 1k5 pull-up on USB
D+. Failure to do this can result in unreliable operation in the field. This is an integral part of the USB
specification and applies to all USB Self Powered devices ( not just FT232BM peripherals ). In this design,
the presence of power on the host/hub USB port is used to control the RESET# pin of the FT232BM.
When the Host / Hub is powered up RSTOUT# pulls the top end of the 1k5 resistor on USB D+ to 3.3v
nominal thus identifying the device as a full speed device to USB. When the Host / HUB powers down,
the FT232BM is reset and RSTOUT# will go low thus preventing current being injected into the Host / Hub
USB D+ line via the 1k5 resistor.
General Design Notes – See Previous Example
DG232 Version 2.0
© Future Technology Devices Intl. Ltd. 2002/2003
Page 5 of 16
1
2
3
4
C2
0.1uF
VCC
DECOUPLING CAPS
C3
10uF
CN1
CN-USB
5
FB1
2
C5
10nF
27R
R5
C1
0.1uF
Y1
6MHz RESONATOR
27R
VCC
R4
FERRITE BEAD
1
R6
VCC
C4
33nF
R2
2k2
1k5
VCC
31
2
1
32
4
28
27
5
7
8
6
C6
0.1uF
R3
470R
© Future Technology Devices Intl. Ltd. 2002/2003
CS
SK
DIN
DOUT
U2
VCC
NC
NC
GND
10k
R1
93C46/56/66
( Optional )
1
2
3
4
8
7
6
5
SLEEP#
RXLED#
TXLED#
PWRCTL
PWREN#
TXDEN
RI#
DCD#
DSR#
DTR#
CTS#
RTS#
RXD
TXD
VCC
FT232BM
10
11
12
14
15
16
18
19
20
21
22
R7
1k
Page 6 of 16
WITH POWER SWITCHING
POWERED APPLICATION
VCC-5v
GND
5v MCU or Logic cct
CTS#
RTS#
RXD
23
TXD
Soft Start
Circuit
24
C8
0.1uF
25
U1
IRLML6402
Q1
FT232B APPLICATION SCHEMATIC
TEST
EEDATA
EESK
EECS
RESET#
XTOUT
XTIN
RSTOUT#
USBDP
USBDM
3V3OUT
VCC
30
AVCC
AGND
29
3
26
13
VCC
VCC
VCC-IO
GND
GND
DG232 Version 2.0
9
17
USB
C7
0.1uF
FT232BM Designers Guide
Figure 3.0
FT232BM – 5 volt Bus Powered Example Schematic with Power Switching ( 232-5VSW )
FT232BM Designers Guide
Figure 3.0 is an example of a 5 volt, USB bus powered design using the FT232BM connected to a 5v MCU or
other external logic. In this design, the FT232BM controls the power to the auxiliary circuitry using PWEREN#
to shut off power to this circuitry when –
1. The FT232BM is in reset, OR
2. The FT232BM has not yet been configured ( successfully recognised and enumerated over USB ), OR
3. USB is in suspend / sleep mode.
•
•
•
•
•
•
•
A P-Channel Logic Level MOSFET is used as a power switch to control the power to the auxiliary devices
– in this example we use a International Rectifier part number IRLML6402. R7 and C8 form a “soft start”
circuit which limits the current surge when the MOSFET turns on. Without this, there is a danger that the
transient power surge of the MOSFET turning on will reset the FT232BM or the USB Host / Hub controller.
The values used allow the attached circuitry to power up with a slew rate of ~ 12.5v per millisecond, in
other words the output voltage will transitioning from GND to 5v in around 400uS.
When using this circuit, enable the “Pull-Down on Suspend” option in the EEPROM. This will ensure
minimum leakage current during sleep ( suspend ) mode by gently pulling down the UART interface pins
of the FT232BM pins to GND during USB suspend.
The auxiliary circuitry attached to the FT232BM device must have it’s own power-on-reset circuitry and
should NOT use RESETO# to generate a reset for this circuitry. RESETO# does not generate a reset
during USB sleep ( suspend ) when the auxiliary logic is powered-off, thus cannot be used as a reset in
this case.
A “USB High-Power Bus Powered Device” ( one that consumes more than 100mA and up to 500mA )
of current from the USB bus during normal operation must use this power control feature to remain
compliant as the USB specification does not allow a USB peripheral to draw more than 100mA of current
from the USB Bus until the device has been successfully enumerated. A “USB High-Power Bus Powered
Device” cannot be plugged into a USB Bus-Powered Hub as these can only supply 100mA per USB port.
The Power ( current ) consumption of the device is set in a field in the 93C46 EEPROM attached to the
FT232BM. A “USB High-Power Bus Powered Device” must use the 93C46 to inform the system of it’s
power requirements.
PWRCTL is tied to GND to tell the device to indicate a bus powered device in it’s USB descriptor.
RTS / CTS handshaking is used in this example. If the MCU has no dedicated handshaking signals then
general purpose IO pins can usually be used to implement the handshaking. If the MCU is guaranteed to
accept data sent from the FT232BM at the programmed baud rate, then a single wire handshake will do (
tie CTS# of the FT232BM to GND ).
General Design Notes – See Previous Examples
DG232 Version 2.0
© Future Technology Devices Intl. Ltd. 2002/2003
Page 7 of 16
CN1
CN-USB
5
C3
10uF
© Future Technology Devices Intl. Ltd. 2002/2003
Page 8 of 16
C2
0.1uF
2
27R
27R
R4
R5
C1
0.1uF
Y1
6MHz RESONATOR
RSTOUT#
C5
10nF
VCC
R6
VCC
C4
33nF
R2
2k2
1k5
VCC
31
2
1
32
4
28
27
5
7
8
6
C6
0.1uF
R3
470R
CS
SK
DIN
DOUT
U2
VCC
NC
NC
GND
10k
R1
93C46/56/66
( Optional )
1
2
3
4
8
7
6
5
SLEEP#
RXLED#
TXLED#
PWRCTL
PWREN#
TXDEN
RI#
DCD#
DSR#
DTR#
CTS#
RTS#
RXD
TXD
VCC
FT232BM
10
11
12
14
15
16
18
19
20
21
22
23
VCC-3.3v
POWERDN#
RESET#
SLEEP#
RSTOUT#
GND
3.3v MCU or Logic cct
CTS#
RTS#
RXD
R7
47k
C7
0.1uF
VCC-3.3V
TXD
O
24
G
25
U1
U3
I
LDO REGULATOR 3.3v
FT232B APPLICATION SCHEMATIC
TEST
EEDATA
EESK
EECS
RESET#
XTOUT
XTIN
RSTOUT#
USBDP
USBDM
3V3OUT
VCC
INTERFACING TO 3.3 V LOGIC - BUS POWERED ( <= 100mA ) APPLICATION
VCC
DECOUPLING CAPS
1
2
3
4
FB1
FERRITE BEAD
1
3
26
13
VCC
VCC
VCC-IO
30
AVCC
AGND
29
DG232 Version 2.0
GND
GND
Figure 4.0
9
17
USB
FT232BM Designers Guide
FT232BM – 3.3 volt Bus Powered Example Schematic ( 232-3VB )
FT232BM Designers Guide
Figure 4.0 is an example of a 3.3 volt, USB bus powered design using the FT232BM connected to a 3.3v MCU
or other external logic.
• The main difference between this circuit and the 5 volt circuit of Figure 1.0 is that a 3.3 volt LDO regulator
i.c. is used to provide a 3.3v supply to the auxiliary circuiry.
• VCC-IO is driven from the 3.3v LDO regulator i.c. in order to drive the UART interface from the FT232BM to
the MCU / external logic at 3.3v level instead of 5v level.
• As the USB supply rail can drop to 4.4 volts or less under load, an LDO ( Low Dropout ) voltage regulator
must be used in this instance.
• The 3.3v LDO voltage regulator must also have a low quiescent ( no load ) current in order to ensure that
the USB suspend current requirement ( <= 500uA ) is met during USB suspend.
• In this example, we assume that the total current of the design is <= 100mA ( low power ), and that the
MCU / logic can detect USB suspend mode using either the SLEEP# or PWREN# pins of the FT232BM and
put itself and any circuitry it is controlling into a low power state in order to meet the total USB suspend
current requirement of 500uA or less.
•
•
•
RSTOUT# is used to provide a power-on reset to the external logic in this example. If the MCU has it’s
own power-on reset logic then there is usually no need to use RSTOUT# to reset the device and this
connection and the 47k pull-down can be omitted. Note : If RSTOUT# is used to reset an external device
AND to pull-up the USB D+ line, it’s Vout high can be as low as 2.2v so it must be used to drive a TTL level
reset input on the external device.
PWRCTL is tied to GND to tell the device to indicate a bus powered device in it’s USB descriptor.
RTS / CTS handshaking is used in this example. If the MCU has no dedicated handshaking signals then
general purpose IO pins can usually be used to implement the handshaking. If the MCU is guaranteed to
accept data sent from the FT232BM at the programmed baud rate, then a single wire handshake will do (
tie CTS# of the FT232BM to GND ).
General Design Notes – See Previous Examples
DG232 Version 2.0
© Future Technology Devices Intl. Ltd. 2002/2003
Page 9 of 16
DG232 Version 2.0
5
CN1
CN-USB
R7
15k
R8
10k
C3
10uF
VCC
C2
0.1uF
DECOUPLING CAPS
1
2
3
4
27R
R5
© Future Technology Devices Intl. Ltd. 2002/2003
Y1
6MHz RESONATOR
C4
33nF
R2
2k2
31
2
1
32
4
28
27
5
7
8
6
C5
0.1uF
R3
470R
CS
SK
DIN
DOUT
U2
10k
R1
TXDEN
RI#
DCD#
DSR#
DTR#
CTS#
RTS#
8
7
6
5
SLEEP#
RXLED#
TXLED#
PWRCTL
PWREN#
VCC
NC
NC
GND
93C46/56/66
( Optional )
1
2
3
4
TXD
RXD
VCC
FT232BM
10
11
12
14
15
16
18
19
20
21
22
Page 10 of 16
UPDATED 21st January 2003
VCC-3v
VCC3V
VCC
POWEREN#
VCC3V
GND
3.3v MCU or Logic cct
CTS#
RTS#
RXD
24
23
TXD
25
U1
FT232B APPLICATION SCHEMATIC
TEST
EEDATA
EESK
EECS
RESET#
XTOUT
XTIN
RSTOUT#
USBDP
USBDM
3V3OUT
VCC
INTERFACING TO 3.3V LOGIC - SELF POWERED APPLICATION
C1
0.1uF
R6
1k5
27R
R4
VCC
30
AVCC
AGND
29
3
26
13
VCC
VCC
VCC-IO
GND
GND
VCC 5.0v
VCC 3.3v
GND
EXTERNAL POWER
C6
0.1uF
Figure 5.0
9
17
USB
FT232BM Designers Guide
FT232BM – 3.3 volt Self Powered Example Schematic ( 232-3VS )
FT232BM Designers Guide
Figure 5.0 is an example of a 3.3 volt, USB self powered design using the FT232BM connected to a 3.3v MCU
or other external logic. A USB self power design has it’s own PSU and does not draw it’s power from the USB
bus. In such a case, no special care need be taken to meet the USB suspend current ( 0.5mA ) as the device
does not get its power from the USB port. The differences between this circuit and that of Figure 2.0 are
minimal. See the notes in Figure 2 for the main details.
•
•
In this case the internal PSU needs to supply 3.3 volts to the auxiliary circuitry and 5 volts to the
FT232BM i.c.
The VCCIO power line to the FT232BM is driven from the 3.3v supply in order to drive the auxiliary logic at
the correct voltage level.
Important Note : In this design, the PWRCTL Pin ( Pin 14 ) of the FT232BM is tied high to indicate a self
powered design. It is important to tie this to VCCIO ( 3.3v ) and NOT to VCC ( 5.0v ) otherwise the input
protection diodes on this pin will conduct and try to pull VCCIO towards 5.0v
As well as being undesirable, this may cause excessive current to be drawn by the FT232BM and the 3.3v
logic attached to this device.
DG232 Version 2.0
© Future Technology Devices Intl. Ltd. 2002/2003
Page 11 of 16
C7
4.7uF
C2
0.1uF
VCC
DECOUPLING CAPS
1
2
3
4
2
C4
10nF
27R
27R
VCC
C1
0.1uF
© Future Technology Devices Intl. Ltd. 2002/2003
Page 12 of 16
R6
VCC
C3
33nF
R2
2k2
1k5
VCC
31
2
1
32
4
28
27
5
7
8
6
C5
0.1uF
R3
470R
CS
SK
DIN
DOUT
U2
VCC
NC
NC
GND
10k
R1
93C46/56/66
( Optional )
1
2
3
4
8
7
6
5
SLEEP#
RXLED#
TXLED#
PWRCTL
PWREN#
TXDEN
RI#
DCD#
DSR#
DTR#
CTS#
RTS#
RXD
TXD
Vo
G Vi
REG1
TC55RP3302
R7
1k
VCC
FT232BM
10
11
12
14
15
16
18
19
20
WITH POWER SWITCHING
VCC-3v
GND
3v MCU or Logic cct
CTS#
21
RTS#
22
RXD
23
TXD
Soft Start
Circuit
C10
0.1uF
24
C9
0.1uF
IRLML6402
Q1
25
U1
FT232B APPLICATION SCHEMATIC
TEST
EEDATA
EESK
EECS
RESET#
XTOUT
XTIN
RSTOUT#
USBDP
USBDM
3V3OUT
VCC
INTERFACING TO 3.3 V LOGIC - BUS POWERED ( <= 250mA ) APPLICATION
Y1
6MHz RESONATOR
R5
R4
FERRITE BEAD
FB1
1
CN1
CN-USB
5
2
1
30
AVCC
AGND
3
26
13
VCC
VCC
VCC-IO
29
DG232 Version 2.0
GND
GND
C6
0.1uF
C8
4.7uF
Figure 6.0
9
17
3
USB
FT232BM Designers Guide
FT232BM – 3.3 volt Switched Power Bus Powered Schematic ( 232-3VSW)
FT232BM Designers Guide
Figure 6.0 is an example of a 3.3 volt, USB bus powered design with power switching using the FT232BM
connected to a 3.3v MCU or other external logic. The circuit is essentially a combination of the schematics of
Figure 3 and Figure 4.
• A 3.3 volt LDO regulator i.c. is used to provide a 3.3v VCCIO rail and switched 3.3v supply to the auxiliary
circuiry via a IRLML6402 P-Channel MOSFET .
• In this example, we use a Telcom / MicroChip TC55RP3302 as the 3.3v LDO regulator. This has a maximum
rated output current of 250mA. If a higher current is required, use an LD1117 / LM1117 series LDO
regulator instead as these are rated to 800mA. The two are not pin compatible.
• R7 and C10 form a soft start circuit which helps prevent excesssive power switching transients when the
MOSFET turns on. We would advise you to include these components as without them the current surge
when the IRLML6402 MOSFET initially turns on can be capable of resetting the FT232BM or tripping the
power sense circuitry in a USB hub.
General Design Notes – See Previous Examples
DG232 Version 2.0
© Future Technology Devices Intl. Ltd. 2002/2003
Page 13 of 16
CN1
CN-USB
C4
10uF
SHIELD
5
1
2
3
4
FB1
C10
10nF
VCC
DECOUPLING CAPS
C3
0.1uF
2
27R
R7
GND
C1
0.1uF
VCC
Y1
6MHz RESONATOR
27R
VCC
R6
FERRITE BEAD
1
© Future Technology Devices Intl. Ltd. 2002/2003
R4
2k2
31
2
1
32
4
28
27
5
7
8
6
C11
0.1uF
R5
470R
CS
SK
DIN
DOUT
U3
10k
R3
TXDEN
RI#
DCD#
DSR#
DTR#
CTS#
RTS#
8
7
6
5
SLEEP#
RXLED#
TXLED#
PWRCTL
PWREN#
VCC
NC
NC
GND
93C46/56/66
( Optional )
1
2
3
4
TXD
RXD
RI#
19
18
VCC
FT232BM
10
11
12
14
15
SLEEP#
DCD#
16
DSR#
DTR#
21
20
CTS#
22
RTS#
RXD
23
TXD
25
24
U2
TX
FT232B APPLICATION SCHEMATIC
TEST
EEDATA
EESK
EECS
RESET#
XTOUT
XTIN
RSTOUT#
USBDP
USBDM
3V3OUT
VCC
VCC
R1
220R
D1
LED
USB <=> RS232 SERIAL CONVERTER ( 300 to 115k/460k baud )
C2
0.1uF
VCC
1k5
R8
C9
33nF
VCC
30
AVCC
AGND
29
3
26
13
VCC
VCC
VCC-IO
GND
GND
DG232 Version 2.0
9
17
C6
0.1uF
C5
0.1uF
VCC
VCC
R2
220R
D2
LED
10
12
14
13
25
24
9
4
27
23
18
CTS
DSR
DCD
RXDATA
RI
SLEEP#
VCC
7
6
20
21
TXD
DTR#
RTS#
RX
RI
DTR
CTS
TXDATA
RTS
RXDATA
DSR
DCD
U1
SKT1
DB9M
SP213EHCA
VCC
C2+
C2-
V-
R1OUT
R2OUT
R3OUT
R4OUT
R5OUT
T1OUT
T2OUT
T3OUT
T4OUT
SHIELD
MAX213CAI
MAX213CWI
ADM213E
SP213ECA
GND
C1+
C1-
V+
SHDN#
EN
R1IN
R2IN
R3IN
R4IN
R5IN
T1IN
T2IN
T3IN
T4IN
5
9
4
8
3
7
2
6
1
11
15
16
17
8
5
26
22
19
2
3
1
28
C8
0.1uF
C7
0.1uF
CTS#
DSR#
DCD#
RXD
RI#
TXDATA
DTR
RTS
VCC
Figure 7.0
10
USB
FT232BM Designers Guide
FT232BM –5v BUS Powered USB => RS232 Converter Example Schematic ( USB-232B )
Page 14 of 16
FT232BM Designers Guide
Figure 7.0 is an example of a 5 volt, USB bus powered design using the FT232BM connected to a TTL ó
RS232 level converter i.c .
• For RS232 applications, the baud rate of the finished product is limited by the ac. driving characteristics
of the level converter i.c. rather than that of the FT232BM.
• This example uses the popular “213” series of TTL to RS232 level converters. These devices have 4
transmitters and 5 receivers in a 28 LD SSOP package and feature an in-built voltage converter to convert
the 5v ( nominal ) VCC to the +/- 9volts required by RS232. An important feature of these devices is the
SHDN# pin which can power down the device to a low quiescent current during USB suspend mode
• The device used in this schematic is a Sipex SP213EHCA which is capable of RS232 communication
at up to 500k baud. If a lower baud rate is acceptable, then several pin compatible alternatives are
available such as Sipex SP213ECA , Maxim MAX213CAI and Analog Devices ADM213E which are good
for communication at up to 115,200 baud. If a higher baud rate is desired, use a Maxim MAX3245CAI part
which is capable of RS232 communication at rates of up to 1M baud.
• Note : the MAX3245 is not pin compatible with the 213 series devices, also it’s SHDN pin is active high so
connect this to PWREN# instead of SLEEP#.
DG232 Version 2.0
© Future Technology Devices Intl. Ltd. 2002/2003
Page 15 of 16
FT232BM Designers Guide
Document Revision History
DG232B Version 1.0 – Initial document created 05 August 2002
DG232B Version 1.1 Created 06 August 2002
•
Added USB-232B application
DG232B Version 2.0 Created 19th May 2003
•
Corrected Pull Up Control Circuit for Self Powered Designs
•
Corrected connection of PWRCTL in 3.3v Self Powered Designs
•
Updated Schematic Drawings
•
Added 3.3v Switched Bus Powered reference schematic
Disclaimer
© Future Technology Devices International Limited , 2002 / 2003
Neither the whole nor any part of the information contained in, or the product described in this manual, may
be adapted or reproduced in any material or electronic form without the prior written consent of the copyright
holder.
This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for
any particular purpose is either made or implied.
Future Technology Devices International Ltd. will not accept any claim for damages howsoever arising as a
result of use or failure of this product. Your statutory rights are not affected.
This product or any variant of it is not intended for use in any medical appliance, device or system in which
the failure of the product might reasonably be expected to result in personal injury.
The information in this document may be subject to change without notice.
Contact Information
Future Technology Devices Intl. Limited
St. George’s Studios
93/97 St. George’s Road,
Glasgow G3 6JA,
United Kingdom.
Tel : +44 ( 0 )141 353 2565
Fax : +44 ( 0 )141 353 2656
E-Mail ( Sales ) : [email protected]
E-Mail ( Support ) : [email protected]
E-Mail ( General Enquiries ) : [email protected]
Web Site URL : http://www.ftdichip.com
Agents and Sales Representatives
At the time of writing our Sales Network covers over 50 different countries world-wide. Please visit the Sales Network
page of our Web Site site for the contact details our distributor(s) in your country.
DG232 Version 2.0
© Future Technology Devices Intl. Ltd. 2002/2003
Page 16 of 16