UMFT201XB, UMFT220XB and UMFT230XB Datasheet Version 1.1 Document Reference No.: FT_000506 Clearance No.: FTDI# 272 Future Technology Devices International Ltd Datasheet UMFT201XB, UMFT220XB, UMFT230XB Breakout Modules USB to I2C/UART/FT1248 breakout modules 1 Introduction 1.1 Features UMFT201XB, UMFT220XB, and UMFT230XB breakout modules utilize FTDI’s FT201XQ, FT220XQ, and FT230XQ chips, respectively, to convert USB to serial or parallel interfaces. . These modules support the following popular interfaces: 2 - UMFT201XB bridges from USB to I2C IC. - UMFT220XB bridges from USB to a user chosen, parallel bit interface, FTDI’s FT1248/SPI. Note: 2 out of the 4 I/0 lines are available for this module. - UMFT230XB bridges from USB to UART IC. This module is a breakout board with a low profile. It converts USB2.0 Full-Speed to a serial interface and connects the serial signals to a 2.54mm (0.1”) pitch 10pin female receptacle. The boards do not use a USB connector, but instead the modules plug directly into the USB host connector and the pads of the PCB makes electrical contact with the electrical contacts of the USB connector. All serial interfaces on these modules operate at +3.3V voltage levels, however all I/Os are 5V tolerant. Driver Support Royalty-Free VIRTUAL COM PORT (VCP) DRIVERS for: Royalty-Free D2XX Direct Drivers (USB Drivers + DLL S/W Interface): Windows 8 32,64-bit Windows 8 32,64-bit Windows 7 32,64-bit Windows 7 32,64-bit Windows Vista Windows Vista Windows XP 32,64-bit Windows XP 32,64-bit Windows XP Embedded Windows XP Embedded Windows CE.NET 4.2 , 5.0 and 6.0 Windows CE.NET 4.2, 5.0 and 6.0 MAC OS OS-X MAC OS OS-X Linux 3.0 and greater Linux 3.0 and greater Android Android The drivers listed above are all available to download for free from www.ftdichip.com. Various 3rd Party Drivers are also available for various other operating systems - visit www.ftdichip.com for details. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. UMFT201XB, UMFT220XB and UMFT230XB Datasheet Version 1.1 Document Reference No.: FT_000506 3 Clearance No.: FTDI# 272 Ordering Information Module Interface Features UMFT201XB I2C USB to I2C with four control bus lines, 3.3V power out (with a 50mA current limit) and fused 5V. Standard option, connector fitted to CN2. UMFT201XB-NC I2C USB to I2C with four control bus lines, 3.3V power out (with a 50mA current limit) and fused 5V. No connector option, no connector is fitted to CN2. UMFT201XB-WE I2C USB to I2C with four control bus lines, 3.3V power out (with a 50mA current limit) and fused 5V. Wire ended option, 6” flying leads fitted to CN2. UMFT220XB 4-bit FT1248 USB to FT1248 uses 2 FT1248 I/O lines, 3.3V power out (with a 50mA current limit) and fused 5V. Standard option, connector fitted to CN2. UMFT220XB-NC 4-bit FT1248 USB to FT1248 uses 2 FT1248 I/O lines, 3.3V power out (with a 50mA current limit) and fused 5V. No connector option, no connector is fitted to CN2. UMFT220XB-WE 4-bit FT1248 USB to FT1248 uses 2 FT1248 I/O lines, 3.3V power out (with a 50mA current limit) and fused 5V. Wire ended option, 6” flying leads fitted to CN2. UMFT230XB Basic UART USB to UART with four control bus lines, 3.3V power out (with a 50mA current limit) and fused 5V. UART rate can be up to 3 Mega Baud. Standard option, connector fitted to CN2. UMFT230XB-NC Basic UART USB to UART with four control bus lines, 3.3V power out (with a 50mA current limit) and fused 5V. UART rate can be up to 3 Mega Baud. No connector option, no connector is fitted to CN2. UMFT230XB-WE Basic UART USB to UART with four control bus lines, 3.3V power out (with a 50mA current limit) and fused 5V. UART rate can be up to 3 Mega Baud. Wire ended option, 6” flying leads fitted to CN2. 2 Copyright © 2013 Future Technology Devices International Limited UMFT201XB, UMFT220XB and UMFT230XB Datasheet Version 1.1 Document Reference No.: FT_000506 Clearance No.: FTDI# 272 Table of Contents 1 Introduction ................................................................................... 1 1.1 Features ........................................................................................................ 1 2 Driver Support ................................................................................ 1 3 Ordering Information ..................................................................... 2 4 Signals and Configurations ............................................................. 4 4.1 UMFT-XB Module Pin Outs ............................................................................. 4 4.2 Signal Descriptions ....................................................................................... 4 4.3 UMFT201XB CN2 Signal Descriptions ............................................................ 5 4.4 UMFT220XB CN2 Signal Descriptions ............................................................ 5 4.5 UMFT230XB CN2 Signal Descriptions ............................................................ 6 4.6 CBUS Signal Options ..................................................................................... 6 4.7 Configuring the MTP ROM .............................................................................. 7 5 Module Dimensions ........................................................................ 8 6 IC Package Markings ...................................................................... 8 7 UMFT-XB-WE Module Wire Connections .......................................... 9 8 9 7.1 UMFT201XB-WE Wire Connections ................................................................ 9 7.2 UMFT220XB-WE Wire Connections .............................................................. 10 7.3 UMFT230XB-WE Wire Connections .............................................................. 10 Module Circuit Schematics ............................................................ 11 8.1 UMFT201XB Schematic ................................................................................ 11 8.2 UMFT220XB Schematic ................................................................................ 11 8.3 UMFT230XB Schematic ................................................................................ 12 Environmental Compliances ......................................................... 12 10 Internal MTP ROM Configuration .................................................. 13 11 Contact Information ..................................................................... 14 Appendix A - List of Figures and Tables ................................................................. 15 Appendix B: Revision History ................................................................................ 16 3 Copyright © 2013 Future Technology Devices International Limited UMFT201XB, UMFT220XB and UMFT230XB Datasheet Version 1.1 Document Reference No.: FT_000506 Clearance No.: FTDI# 272 Signals and Configurations 4 For all three modules, CN1 connects directly to a USB host or HUB port, or can be connected to a USB extension cable. This connects the USB data signals, 5V USB Bus power and GND. When connecting these modules to a USB host or HUB the USB signal pads should be facing upwards, and when connecting to vertical connector the USB signal pad should be facing right. If the module is plugged in the wrong way, no contact will be made between PCB and HUB, no damage will occur from plugging the module in upside down. 4.1 UMFT-XB Module Pin Outs Pin UMFT201XB UMFT220XB UMFT230XB 1 SCL IO0 TXD 2 VBUS VBUS VBUS 3 GND GND GND 4 RESET RESET# RESET# 5 SDA SCK RXD 6 3V3 3V3 3V3 7 CB0 SS# RTS# 8 CB2 CB3 CB0 9 CB1 MISO CTS# 10 CB3 IO1 CB1 Table 4.1 Module PinOut List 4.2 Pin No. Signal Descriptions Name Type Description PWR 5V power input USB port. For a low power USB bus powered design, up to 100mA can be sourced from the 5V supply on the USB bus. A maximum of 500mA can be sourced from the USB bus in a high power USB bus powered design. 1 VBUS 2 D- Signal Negative USB data signal 3 D+ Signal Positive USB data signal 4 GND PWR Module Ground Supply Table 4.2 CN1 PinOut Description 4 Copyright © 2013 Future Technology Devices International Limited UMFT201XB, UMFT220XB and UMFT230XB Datasheet Version 1.1 Document Reference No.: FT_000506 Clearance No.: FTDI# 272 4.3 UMFT201XB CN2 Signal Descriptions Pin No. Name Type Description 1 SCL Input I2C clock input 2 VBUS PWR Output 3 GND PWR Module Ground Supply 4 RST# Input Can be used by an external device to reset the FT201X. If not required can be left unconnected, or pulled up to VCCIO. 5 SDA I/O 6 3V3 Output 7 CB0 I/O 8 CB2 I/O 9 CB3 I/O 10 CB3 I/O 5V Power output USB port. I2C bi-directional data line 3.3V output from integrated LDO regulator. This pin is decoupled to ground on the module PCB with a 10nF capacitor. The prime purpose of this pin is to provide the internal 3.3V supply to the USB transceiver cell. Configurable CBUS I/O Pin. Function of this pin is configured in the device internal MTP ROM. Factory Default pin Function is PWREN#. See CBUS Signal Options, Table 4.6 Configurable CBUS I/O Pin. Function of this pin is configured in the device internal MTP ROM. Factory Default pin Function is SLEEP#. See CBUS Signal Options, Table 4.6 Configurable CBUS I/O Pin. Function of this pin is configured in the device internal MTP ROM. Factory Default pin Function is Tristate. See CBUS Signal Options, Table 4.6 Configurable CBUS I/O Pin. Function of this pin is configured in the device internal MTP ROM. Factory Default pin Function is Tristate. See CBUS Signal Options, Table 4.6 Table 4.3 I2C Module Pin Out Description 4.4 UMFT220XB CN2 Signal Descriptions Pin No. Name Type Description 1 IO0 I/O FT1248 Bi-Directional data bit 0 2 VBUS PWR Output 3 GND PWR Module Ground Supply 4 RST# Input Can be used by an external device to reset the FT220X. If not required can be left unconnected, or pulled up to VCCIO. 5 SCK Input FT1248 Clock input from FT1248 interface master 6 3V3 Output 7 SS# Input 8 CB3 I/O 9 MISO Output 5V Power output USB port. 3.3V output from integrated LDO regulator. This pin is decoupled to ground on the module PCB with a 10nF capacitor. The prime purpose of this pin is to provide the internal 3.3V supply to the USB transceiver cell. FT1248 Chip select input to enable the device interface. Active low logic. Configurable CBUS I/O Pin. Function of this pin is configured in the device internal MTP ROM. Factory Default pin Function is PWREN#. See CBUS Signal Options, Table 4.6 Master In Serial Out. Used to provide status information to the FT1248 interface master. 10 IO1 I/O FT1248 Bi-Directional data bit 1 Table 4.4 FT1248 Module Pin Out Description 5 Copyright © 2013 Future Technology Devices International Limited UMFT201XB, UMFT220XB and UMFT230XB Datasheet Version 1.1 Document Reference No.: FT_000506 Clearance No.: FTDI# 272 4.5 UMFT230XB CN2 Signal Descriptions Pin No. Name Type Description 1 TXD Output UART Transmit Asynchronous Data Output. 2 VBUS PWR Output 5V Power output USB port. 3 GND PWR Module Ground Supply 4 RST# Input Can be used by an external device to reset the FT230X. If not required can be left unconnected, or pulled up to VCCIO. 5 RXD Input UART Receiving Asynchronous Data Input. 6 3V3 Output 3.3V output from integrated LDO regulator. This pin is decoupled to ground on the module PCB with a 10nF capacitor. The prime purpose of this pin is to provide the internal 3.3V supply to the USB transceiver cell. 7 RTS# Output UART Request to Send Control Output / Handshake Signal. 8 CB0 I/O 9 CTS# Input 10 CB1 I/O Configurable CBUS I/O Pin. Function of this pin is configured in the device internal MTP ROM. Factory Default pin Function is PWREN#. See CBUS Signal Options, Table 4.6 UART Clear To Send Control Input / Handshake Signal. Configurable CBUS I/O Pin. Function of this pin is configured in the device internal MTP ROM. Factory Default pin Function is SLEEP#. See CBUS Signal Options, Table 4.6 Table 4.5 UART Module Pin Out Description 4.6 CBUS Signal Options CBUS Signal Option Available On CBUS Pin*** TRI-STATE CBUS0, CBUS1, CBUS2, CBUS3 IO Pad is tri-stated DRIVE_1 CBUS0, CBUS1, CBUS2, CBUS3 Output a constant 1 DRIVE_0 CBUS0, CBUS1, CBUS2, CBUS3 Output a constant 0 TXDEN CBUS0, CBUS1, CBUS2, CBUS3 Enable transmit data for RS485 (Only in UMFT230XB) PWREN# CBUS0, CBUS1, CBUS2, CBUS3 Output is low after the device has been configured by USB, then high during USB suspend mode. This output can be used to control power to external logic P-Channel logic level MOSFET switch. Internal drive configuration consists of an open drain to GND with no pull-up, specially designed for battery charging applications.* TXLED# CBUS0, CBUS1, CBUS2, CBUS3 Transmit data LED drive – pulses low when transmitting data via USB. RXLED# CBUS0, CBUS1, CBUS2, CBUS3 Receive data LED drive – pulses low when receiving data via USB. TX&RXLED# CBUS0, CBUS1, CBUS2, CBUS3 LED drive – pulses low when transmitting or receiving data via USB. SLEEP# CBUS0, CBUS1, CBUS2, CBUS3 Goes low during USB suspend mode. Typically used to power down an external TTL to RS232 level converter IC in USB to RS232 converter designs. CLK24MHz CBUS0, CBUS1, CBUS2, CBUS3 24 MHz Clock output.** CLK12MHz CBUS0, CBUS1, CBUS2, CBUS3 12 MHz Clock output.** Description 6 Copyright © 2013 Future Technology Devices International Limited UMFT201XB, UMFT220XB and UMFT230XB Datasheet Version 1.1 Document Reference No.: FT_000506 Clearance No.: FTDI# 272 CBUS Signal Option Available On CBUS Pin*** CLK6MHz CBUS0, CBUS1, CBUS2, CBUS3 6 MHz Clock output.** GPIO CBUS0, CBUS1, CBUS2, CBUS3 CBUS bit bang mode option. Allows up to 4 of the CBUS pins to be used as general purpose I/O. Configured individually for CBUS0, CBUS1, CBUS2 and CBUS3 in the internal MTP ROM. A separate application note, AN232R-01, available from FTDI website (www.ftdichip.com) describes in more detail how to use CBUS bit bang mode. BCD_Charger CBUS0, CBUS1, CBUS2, CBUS3 Battery charge Detect, indicates when the device is connected to a dedicated battery charger host. Active high output. BCD_Charger# CBUS0, CBUS1, CBUS2, CBUS3 Inverse of BCD Charger BitBang_WR# CBUS0, CBUS1, CBUS2, CBUS3 Synchronous and asynchronous bit bang mode WR# strobe output. BitBang_RD# CBUS0, CBUS1, CBUS2, CBUS3 Synchronous and asynchronous bit bang mode RD# strobe output. I2C_TXE# CBUS0, CBUS1, CBUS2, CBUS3 Transmit buffer empty, used to indicate to I2C master device status of the FT201X transmit buffer I2C_RXF# VBUS_Sense Description CBUS0, CBUS1, CBUS2, CBUS3 Receive buffer full, used to indicate to I2C master device status of FT201X receive buffer CBUS0, CBUS1, CBUS2, CBUS3 Input to detect when VBUS is present. Time_Stamp CBUS0, CBUS1, CBUS2, CBUS3 Table 4.6 CBUS Configuration Control Toggle signal which changes state each time a USB SOF is received For further information on CBUS options, please refer to the relevant x-chip datasheet. * PWREN# must be used with a 10kΩ resistor pull up. **When in USB suspend mode the outputs clocks are also suspended. ***The number of CBUS pins available varies for the three different modules. 4.7 Configuring the MTP ROM The IC on each of the modules contains an embedded MTP memory that can be used to specify the functions of the CBUS pins, the current drive on each signal pin, current limit for the USB bus and the descriptors of the device. For details on using the MTP ROM/EEPROM programming utility FT_PROG, please see the FT_PROG User Guide. When programming the MT memory please note: i) The Max Bus Power setting of the MTP ROM should specify the maximum current to be drawn from the USB host/hub when enumerated. For high-powered USB devices the current limit when enumerated is between 100mA and 500mA, for low-powered USB devices the current limit is 100mA. 7 Copyright © 2013 Future Technology Devices International Limited UMFT201XB, UMFT220XB and UMFT230XB Datasheet Version 1.1 Document Reference No.: FT_000506 5 Clearance No.: FTDI# Module Dimensions 14.95 2.36 2.54 12.10 38.46 15.51 14.10 45.5 5.2 2.00 Measurements given in millimetres Tolerance +/-0.1mm Figure 5.1 UMFT-XB Module Dimensions The UMFT201XB, UMFT220XB and UMFT230XB modules are mechanically identical. Figure 5.1 Uses UMFT230 to illustrate the mechanical details. 6 IC Package Markings 1 FTDI I XXXXXXXXXX 12 FT201XQ YYWW-D 5 8 The date code format is YYXX where XX = 2 digit week number, YY = 2 digit year number. This is followed by the revision letter. The code XXXXXXX is the manufacturing LOT code. 8 Copyright © 2013 Future Technology Devices International Limited 272 UMFT201XB, UMFT220XB and UMFT230XB Datasheet Version 1.1 Document Reference No.: FT_000506 7 Clearance No.: FTDI# UMFT-XB-WE Module Wire Connections 7.1 UMFT201XB-WE Wire Connections 2 VBUS 2 SCL 1 1 ORANGE SDA 5 5 YELLOW CB0 7 7 GREEN CB1 9 9 BROWN CB2 8 8 GREY CB3 10 10 RESET# 4 4 WHITE 6 BLUE 3 BLACK 3v3 GND 6 3 Wire 6" RED PURPLE Figure 7.1 UMFT201XB-WE Wire Connections (numbers refer to pad numbers on the PCB) Figure 6.1 illustrates the –WE product as a cable. This is only for illustration purposes. The wire ended product consists of individual wires – not a cable 9 Copyright © 2013 Future Technology Devices International Limited 272 UMFT201XB, UMFT220XB and UMFT230XB Datasheet Version 1.1 Document Reference No.: FT_000506 Clearance No.: FTDI# 7.2 UMFT220XB-WE Wire Connections VBUS IO0 2 2 1 1 IO1 10 10 SCK 5 5 SS# 7 MISO 9 9 CB3 8 8 RESET# 4 4 3v3 GND 7 Wire 6" 6 6 3 3 RED ORANGE YELLOW GREEN BROWN GREY PURPLE WHITE BLUE BLACK Figure 7.2 UMFT220XB-WE Wire Connections (numbers refer to pad numbers on the PCB) Figure 6.2 illustrates the –WE product as a cable. This is only for illustration purposes. The wire ended product consists of individual wires – not a cable 7.3 UMFT230XB-WE Wire Connections VBUS TXD 2 2 1 1 RXD 5 5 RTS# 7 7 CTS# 9 9 Wire 6" CB0 8 8 CB1 10 10 4 4 RESET# 3v3 GND 6 3 RED ORANGE YELLOW GREEN BROWN GREY PURPLE WHITE 6 3 BLUE BLACK Figure 7.3 UMFT230XB-WE Wire Connections (numbers refer to pad numbers on the PCB) Figure 6.3 illustrates the –WE product as a cable. This is only for illustration purposes. The wire ended product consists of individual wires – not a cable 10 Copyright © 2013 Future Technology Devices International Limited 272 UMFT201XB, UMFT220XB and UMFT230XB Datasheet Version 1.1 Document Reference No.: FT_000506 8 Clearance No.: FTDI# Module Circuit Schematics 8.1 UMFT201XB Schematic Figure 8.1 UMFT201XB Circuit Schematic 8.2 UMFT220XB Schematic Figure 8.2 UMFT220XB Circuit Schematic 11 Copyright © 2013 Future Technology Devices International Limited 272 UMFT201XB, UMFT220XB and UMFT230XB Datasheet Version 1.1 Document Reference No.: FT_000506 Clearance No.: FTDI# 8.3 UMFT230XB Schematic Figure 8.3 UMFT230XB Circuit Schematic 9 Environmental Compliances The UMFT-XB modules exclusively use lead free components, and are fully compliant with European Union directive 2002/95/EC. 12 Copyright © 2013 Future Technology Devices International Limited 272 UMFT201XB, UMFT220XB and UMFT230XB Datasheet Version 1.1 Document Reference No.: FT_000506 10 Clearance No.: FTDI# 272 Internal MTP ROM Configuration Following a power-on reset or a USB reset the FT-X chips will scan its internal MTP ROM and read the USB configuration descriptors stored there. The default values programmed into the internal MTP ROM in the FT201/220/230XB modules is shown in Table 10.1. Parameter Value Notes USB Vendor ID (VID) 0403h FTDI default VID (hex) USB Product UD (PID) 6015h FTDI default PID (hex) Serial Number Enabled? Yes Serial Number See Note A unique serial number is generated and programmed into the MTP ROM during final test of the FT201/220/230XB modules. Pull down I/O Pins in USB Suspend Disabled Enabling this option will make the device pull down on the UART interface lines when the power is shut off (PWREN# is high). Manufacturer Name FTDI Product Description UMFT201XB / UMFT220XB / UMFT230XB Max Bus Power Current Power Source 90mA Bus Powered Device Type FT201X / FT220X / FT230X USB Version 0200 Returns USB 2.0 device description to the host. Note: The device is a USB 2.0 Full Speed device (12Mb/s). Remote Wake Up Enabled Taking RI# low will wake up the USB host controller from suspend. High Current I/Os Disabled Enables the high drive level on the serial and CBUS I/O pins. Load VCP Driver Enabled Makes the device load the VCP driver interface for the device. UMFT201XB-01 CBUS0 GPIO UMFT201XB-01 CBUS1 GPIO UMFT201XB-01 CBUS2 GPIO UMFT201XB-01 CBUS3 GPIO UMFT220XB-01 CBUS3 Tristate UMFT230XB-01 CBUS0 GPIO FT201X = 0x03, FT220X = 0x02, FT230X = 0x00 UMFT230XB-01 CBUS1 GPIO Table 10.1 Default Internal MTP ROM Configuration The internal MTP ROM in the FT-X chip can be programmed over USB using the utility program FT_PROG. FT_PROG can be downloaded from the www.ftdichip.com. Users who do not have their own USB vendor ID but who would like to use a unique Product ID in their design can apply to FTDI for a free block of unique PIDs. Contact FTDI Support ([email protected]) for this service. 13 Copyright © 2013 Future Technology Devices International Limited UMFT201XB, UMFT220XB and UMFT230XB Datasheet Version 1.1 Document Reference No.: FT_000506 11 Clearance No.: FTDI# 272 Contact Information Head Office – Glasgow, UK Branch Office – Hillsboro, Oregon, USA Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 7130 SW Fir Loop Tigard, OR 97223 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) E-Mail (Sales) E-Mail (Support) E-Mail (General Enquiries) [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] Branch Office – Taipei, Taiwan Branch Office – Shanghai, China 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8797 1330 Fax: +886 (0) 2 8751 9737 Room 1103, No. 666 West Huaihai Road, Shanghai, 200052 China Tel: +86 (0)21 6235 1596 Fax: +86 (0)21 6235 1595 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) E-mail (Sales) E-mail (Support) E-mail (General Enquiries) [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] Web Site http://ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performance requirements. All application-related information in this document (including application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640 14 Copyright © 2013 Future Technology Devices International Limited UMFT201XB, UMFT220XB and UMFT230XB Datasheet Version 1.1 Document Reference No.: FT_000506 Clearance No.: FTDI# 272 Appendix A - List of Figures and Tables List of Figures Figure 5.1 UMFT-XB Module Dimensions ..................................................................................................... 8 Figure 7.1 UMFT201XB-WE Wire Connections (numbers refer to pad numbers on the PCB) ................ 9 Figure 7.2 UMFT220XB-WE Wire Connections (numbers refer to pad numbers on the PCB) .............. 10 Figure 7.3 UMFT230XB-WE Wire Connections (numbers refer to pad numbers on the PCB) .............. 10 Figure 8.1 UMFT201XB Circuit Schematic .................................................................................................. 11 Figure 8.2 UMFT220XB Circuit Schematic .................................................................................................. 11 Figure 8.3 UMFT230XB Circuit Schematic .................................................................................................. 12 List of Tables Table 4.1 Module PinOut List ......................................................................................................................... 4 Table 4.2 CN1 PinOut Description ................................................................................................................. 4 2 Table 4.3 I C Module Pin Out Description ..................................................................................................... 5 Table 4.4 FT1248 Module Pin Out Description ............................................................................................. 5 Table 4.5 UART Module Pin Out Description ................................................................................................ 6 Table 4.6 CBUS Configuration Control .......................................................................................................... 7 Table 10.1 Default Internal MTP ROM Configuration ................................................................................. 13 Copyright © 2012 Future Technology Devices International Limited 15 UMFT201XB, UMFT220XB and UMFT230XB Datasheet Version 1.1 Document Reference No.: FT_000506 Clearance No.: FTDI# 272 Appendix B: Revision History Document Title: UMFT201XB, UMFT220XB and UMFT230XB Document Reference No.: FT_000506 Clearance No.: FTDI# 272 Product Page: http://www.ftdichip.com/FT-X.htm Document Feedback: Send Feedback Version 1.0 Initial Datasheet Created 09/02/12 Version 1.1 Updated Photos and added Window 8 to driver support list 31/01/13 Copyright © 2012 Future Technology Devices International Limited 16