Future Technology Devices International Ltd The DB9-USB Family of UART Converter Modules Datasheet Document Reference No.: FT_000204 Version 2.0 Issue Date: 2011-08-31 Future Technology Devices International Ltd (FTDI) Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow, G41 1HH, United Kingdom Tel.: +44 (0) 141 429 2777 Fax: + 44 (0) 141 429 2758 E-Mail (Support): [email protected] Web: http://www.ftdichip.com Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. Copyright © 2011 Future Technology Devices International Limited Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 1 Introduction 1.1 The DB9-USB Family of UART Converter Modules The DB9-USB connector modules can be used to upgrade an RS232 port to an active USB port without the need to redesign the PCB. The DB9-USB family consist of 6 modules. Two of these operate at RS232 voltage levels, while four of them operate at digital voltage levels (a choice of 5V or 3.3V). Each is available to replace either a male or a female DB9. 1.2 Functional Description DB9-USB modules can be used to upgrade a UART port of a device to an active USB port without the need for redesigning the device’s PCB. These active connectors contain all the USB to UART (and viceversa) conversion electronics and are designed to fit directly into the same PCB footprint as a PC compatible UART DB9 connector. The FTDI DB9-USB-RS232 modules are available in two types DB9-USB-RS232-M and DB9-USB-RS232-F. A DB9-USB-RS232-M can be used to replace a male DB9 connector that is wired in a PC compatible RS232 manner. This module operates at RS232 signal levels. A DB9-USB-RS232-F can be used to replace a female DB9 connector that is wired in a PC compatible RS232 manner. This module operates at RS232 signal levels. The FTDI DB9-USB-D3 modules are available in two types DB9-USB-D3-M and DB9-USB-D3-F. A DB9-USB-D3-M can be used to replace a male DB9 connector that is wired in a PC compatible RS232 manner. This module operates at 3.3V signal levels. A DB9-USB-D3-F can be used to replace a female DB9 connector that is wired in a PC compatible RS232 manner. This module operates at 3.3V signal levels. The FTDI DB9-USB-D5 modules are available in two types DB9-USB-D5-M and DB9-USB-D5-F. A DB9-USB-D5-M can be used to replace a male DB9 connector that is wired in a PC compatible RS232 manner. This module operates at 5.0V signal levels. A DB9-USB-D5-F can be used to replace a female DB9 connector that is wired in a PC compatible RS232 manner. This module operates at 5.0V signal levels. The purposes of these modules is to provide a simple method of adapting legacy serial devices with UART interfaces to modern USB ports by replacing the DB9 connector with this miniaturised module which closely resembles a DB9 connector. This is accomplished by incorporating the industry standard FTDI FT232R USB-Serial Bridge IC. The RS232 level DB9-USB modules include an RS232 level transceiver. Figure 1.1 – DB9-USB Family Copyright © 2011 Future Technology Devices International Limited 1 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 DB9-USB modules use a standard USB-MINI-B connector for connection to an upstream host or hub port. RS232 Level: RS232 level signals, includes modem handshake signals, and capable of transmitting data at rates up to 1 Mega Baud. Digital Level: 3.3V or 5V level signals, includes modem handshake signals, and capable of transmitting data at rates up to 3 Mega Baud. DB9-USB modules require USB device drivers, available free from www.ftdichip.com, which are used to make DB9-USB modules appear as a Virtual COM Port (VCP). This allows existing serial communications software, such as HyperTerminal, to exchange data through the DB9-USB to a legacy UART peripheral device. 1.3 Background In the long distant past, there was no standard defined for the connections on a DB9 connector when it was used as an RS232 interface. That changed when IBM introduced the PC-AT. This introduced a generally accepted DB9 RS232 standard and PC peripherals adopted the same pin-out using a 1-to-1 cable connection between the PC and the peripheral. DB9-USB modules have adopted this standard. The DB9 connector wire schemes used by this module either the standard male or standard female wire configuration. Note that NOT ALL peripheral adopted this standard so it is important for the user to check against the pin-out used for the male and female DB9-USB connectors. Note: DB9 connectors are also known as DE9 connector since it consists of 9 pins in a size E shell. However DE9 connectors are more commonly referred to as DB9 connector. Copyright © 2011 Future Technology Devices International Limited 2 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 1.4 Block Diagrams DB9 Module DB9 Module USB Mini B Client Connector FTDI FT232R USB Serial Bridge RS232 Level Shifter DB9 PCB Decal Figure 1.2 – DB9-USB-RS232 Block Diagram DB9 Module DB9 Module VIO 3.3V VIO 3.3V 3V3OUT 3V3OUT FTDI FTDI FT232R USB FT232R USB Serial Bridge Serial Bridge USB Mini B Client Connector 3.3V TTL/CMOS 3.3V TTL/CMOS UART UART DB9 PCB Decal Figure 1.3 – DB9-USB-D3 Block Diagram 5V 5V USB Mini B Client Connector DB9 Module DB9 Module VIO VIO FTDI FT232R USB Serial Bridge 5V TTL/CMOS 5VUART TTL/CMOS UART DB9 PCB Decal Figure 1.4 – DB9-USB-D5 Block Diagram 1.4.1 Block description USB Mini B Client Connector This connector provides the interface for connection to a USB Host or Hub port. FTDI FT232R The FTDI FT232R provides the USB-to-Serial conversion. Operating system device drivers are required in order to operate with the FT232R to provide the Virtual COM Port serial functionality. RS232 Level Shifter The RS232 level shifter converts the signals provided by the FT232R into the voltage levels required by application RS232 interface. DB9-USB PCB Footprint The DB9-USB pin-out is configured to match the industry standard DB9 footprint. See section 3. Copyright © 2011 Future Technology Devices International Limited 3 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 1.5 Features Adds one USB serial port by connecting to the RS232 DB9 footprint of a device Easy placement for an standard Male and Female RS232 DB9 footprint of a device A selection of RS232, 3.3V or 5V UART signal levels. Works with USB 1.1 & 2.0 Host and Hub ports Industry Standard FTDI chip set & device drivers for maximum compatibility Microsoft Windows® WHQL-certified, Mac OS X, Linux and Windows CE device drivers Installs as a standard Windows COM port 128 byte transmit buffer, 256 byte receive buffer UART data signals: TxD, RxD, RTS, CTS, DSR, DTR, DCD, RI, GND Powered by USB port. No external power adapter required. Serial port speed up to 1Mbps (RS232 levels) or 3Mbps (3.3V/5V levels) Serial Communication Parameters o Parity: None, Even, Odd o Data bits: 7, 8 o Flow control: RTS/CTS , DSR/DTR, X-ON/X-OFF, None Operating temperature of -40°C to +85°C Copyright © 2011 Future Technology Devices International Limited 4 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 1.6 Technical Specification & Ordering Information Parameter Performance USB Interface 12Mbps USB 2.0 Full-Speed RS232 Interface Standard Windows baud rates (300bps to 921.6Kbps) Custom baud rates (300bps to 1Mbps) through baud rate aliasing. See FTDI Application Note: Configuring FT232R, FT2232 and FT232BM Baud Rates UART Standard Windows baud rates (300bps to 921.6Kbps) Custom baud rates (300bps to 3Mbps) through baud rate aliasing. Table 1.1 – Performance Specifications Product Name Part Number Description DB9-USB-RS232-M DB9-USB-M Full Speed USB to 1-Port RS232 level UART module that can replace an RS232 Level UART DB9 male connector DB9-USB-RS232-F DB9-USB-F Full Speed USB to 1-Port RS232 level UART module that can replace an RS232 level UART DB9 female connector DB9-USB-D3-M DB9-USB-D3-M Full Speed USB to 1-Port 3.3V level UART module that can replace 3.3V level UART DB9 male connector DB9-USB-D3-F DB9-USB-D3-F Full Speed USB to 1-Port 3.3V level UART module that can replace 3.3V level UART DB9 female connector DB9-USB-D5-M DB9-USB-D5-M Full Speed USB to 1-Port 5V level UART module that can replace 5V UART DB9 male connector DB9-USB-D5-F DB9-USB-D5-F Full Speed USB to 1-Port 5V level UART module that can replace 5V UART DB9 female connector Table 1.2 – Ordering Information Copyright © 2011 Future Technology Devices International Limited 5 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 Table of Contents: 1 Introduction ................................................................................... 1 1.1 The DB9-USB Family of UART Converter Modules .......................................... 1 1.2 Functional Description .................................................................................. 1 1.3 Background ................................................................................................... 2 1.4 Block Diagrams ............................................................................................. 3 1.4.1 Block description ....................................................................................... 3 1.5 Features ........................................................................................................ 4 1.6 Technical Specification & Ordering Information ............................................ 5 2 USB Connections ............................................................................ 7 3 UART Connections .......................................................................... 8 4 3.1.1 Male DB9 UART Connector Signals ............................................................. 10 3.1.2 FEMALE DB9 UART Connector Signals ........................................................ 11 Installation ................................................................................... 12 4.1 5 Device Driver Installation ........................................................................... 12 4.1.1 Microsoft Windows Installation .................................................................. 12 4.1.2 Mac OS X, Linux, Windows CE ................................................................... 16 Electrical details ........................................................................... 17 5.1 USB ............................................................................................................. 17 5.2 RS232 ......................................................................................................... 17 5.3 3.3V Level UART .......................................................................................... 17 5.4 5V Level UART ............................................................................................. 17 6 Mechanical Details ........................................................................ 18 7 Physical Environment Details ....................................................... 19 8 9 7.1 Storage ....................................................................................................... 19 7.2 Operating .................................................................................................... 19 Environmental Approvals & Declarations ...................................... 20 8.1 EMI Compatibility ........................................................................................ 20 8.2 Safety.......................................................................................................... 20 8.3 Environmental ............................................................................................. 20 8.4 Reliability .................................................................................................... 20 8.5 Import / Export Information ....................................................................... 21 Troubleshooting ........................................................................... 22 10 Contact Information ..................................................................... 23 Appendix A – References....................................................................................... 25 Appendix B – Revision History .............................................................................. 25 Copyright © 2011 Future Technology Devices International Limited 6 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 2 USB Connections DB9-USB modules are downstream USB 2.0 Devices. A “USB mini B” receptacle is mounted inside the modules to facilitate connection to an upstream USB Host or Hub. Pin Number Pin Type Description 1 Power VBUS – USB Power provided from upstream USB Host or Hub 2 Bidirectional D– = USB data signal, negative polarity 3 Bidirectional D+ = USB data signal, positive polarity 4 ID Not Connected 5 Ground GND = USB signal ground Shield Case Ground Drain = typically connected to the host PC case Table 2.1 – USB “mini-B” Receptacle Pin-Out Copyright © 2011 Future Technology Devices International Limited 7 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 3 UART Connections The PC compatible accepted electrical connections for male and female UART DB9 connectors are illustrated in Figure 3.1 where the structure on the left is the top view of a male UART DB9 connector and the structure on the right is the top view of a female UART DB9 connector. Assuming a design follows these connection conventions, then an FTDI male or female DB9-USB connector can be used to replace this UART DB9 connector to turn this port into an active USB interface. 5 GND UART Transceiver 4 DTR CTS TXD RTS 2 RXD DSR RI RI 8 8 7 RTS RXD 1 DCD 9 CTS 3 TXD 9 MALE FEMALE RI 4 DSR 3 RXD DTR CTS RTS 7 TXD RTS 6 6 DSR DSR DCD DTE GND RXD CTS TXD 2 UART Transceiver DTR GND 5 GND RI DTR DCD 1 DCD PCB PCB DCE Figure 3.1 – Male and Female DB9-USB internal connections (top view looking through the module) Examples and signal directions are shown in Figure 3.2 and Figure 3.3 Copyright © 2011 Future Technology Devices International Limited 8 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 DCD DSR RXD RTS TXD CTS DTR RI GND DB9 Pin1 DB9 Pin6 DB9 Pin2 DB9 Pin7 DB9 Pin3 DB9 Pin8 DB9 Pin4 DB9 Pin9 DB9 Pin5 DCD DSR RXD RTS TXD CTS DTR RI GND Figure 3.2 – DB9-USB-RS232-M Connection illustration GND RI DTR CTS TXD RTS RXD DSR DCD DB9 Pin5 DB9 Pin9 DB9 Pin4 DB9 Pin8 DB9 Pin3 DB9 Pin7 DB9 Pin2 DB9 Pin6 DB9 Pin1 RI RTS CTS DTR GND DSR RXD TXD DCD Figure 3.3 – DB9-USB-RS232-F Connection illustration Copyright © 2011 Future Technology Devices International Limited 9 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 3.1.1 Male DB9 UART Connector Signals The DB9-USB-X-M can be used to replace a male DB9 connector used for transmitting UART signals. Table 2.1 gives the pin out description of each pin/pad of a UART connector/footprint. Pin Pin Type of DB9- Pad Type at Number USB module application PCB 1 Input1 Input1 DCD = Data Carrier Detect 2 Output Input RXD = Receive Data (this is an output from the DB9-USB-X-M to the application Rx input) 3 Input Output 4 Input Output 5 Ground Ground 6 Output Input 7 Input Output 8 Output Input 9 Input1 Input1 Shield Ground Description TXD = Transmit Data (this is an input to the DB9-USB-X-M from the application Tx output) DTR = Data Terminal Ready (this is an input to the DB9-USB-X-M from the application DTR output) GND = RS232 signal ground DSR = Data Set Ready (this is an output from the DB9-USB-X-M to the application DSR input) RTS = Request To Send (this is an input to the DB9-USB-X-M from the application RTS output) CTS = Clear To Send (this is an output from the DB9-USB-X-M to the application CTS input) RI = Ring Indicator Drain = typically connected to the host PC case Table 2.1 – Male DB9 UART Signal Description Case Ground Note 1: These signals are irrelevant for DTE to DTE connections. Copyright © 2011 Future Technology Devices International Limited 10 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 3.1.2 FEMALE DB9 UART Connector Signals The DB9-USB-X-F can be used to replace a female DB9 connector used for transmitting UART signals. Table 2.2 gives the pin out description of each pin/pad of an UART connector/footprint. Pin Number Pin Type of DB9-USB module Pad Type at application PCB 1 Input Output 2 Input Output Description DCD = Data Carrier Detect (this is an input to the DB9-USB-X-F from the application DCD output) RXD = Receive Data (this is an input to the DB9-USB-X-F from the application Tx output, normally labelled RXD in DCE convention) TXD = Transmit Data 3 Output Input (this is an output to the DB9-USB-X-F from the application Rx input, normally labelled TXD in DCE convention) DTR = Data Terminal Ready 4 Output Input 5 Ground Ground (this is an output to the DB9-USB-X-F from the application DSR input, normally labelled DTR in DCE convention) GND = RS232 signal ground DSR = Data Set Ready 6 Input Output (this is an input to the DB9-USB-X-F from the application DTR output, normally labelled DSR in DCE convention) RTS = Request To Send 7 Output Input (this is an output to the DB9-USB-X-F from the application CTS input, normally labelled RTS in DCE convention) CTS = Clear To Send 8 Input Output 9 Input Output Shield Ground (this is an input to the DB9-USB-X-F from the application RTS output, normally labelled CTS in DCE convention) RI = Ring Indicator (this is an input to the DB9-USB-X-F from the application RI output) Case Ground Drain = typically connected to the host PC case Table 2.2 – Female DB9 UART Signal Description Copyright © 2011 Future Technology Devices International Limited 11 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 4 Installation 4.1 Device Driver Installation The drivers for the DB9-USB modules are available for download from: www.ftdichip.com The following section illustrates an example installation on the Windows OS. 4.1.1 Microsoft Windows Installation With the device drivers being Windows Hardware Quality Labs (WHQL) certified, they are also available through download directly from the Microsoft® Windows® Update service. Additional installation options are noted below: Installation Executable shown on Windows XP 1) Login to the system as Administrator, or a user with Administrator rights. 2) Prior to connecting the DB9-USB module to the USB Host or Hub port, download the latest device driver version from the FTDI Chip web site. 3) Run this executable to install the device drivers. 4) Connect the DB9-USB module to your computer. A notification will appear near the task bar indicating that new hardware has been installed and is ready for use. It is normal if this notice appears twice. Figure 3.1 – Hardware Ready Windows Update shown on Windows XP You must have an active Internet connection and the Windows Update Service enabled. 1) Connect the DB9-USB module to your USB Host or Hub. 2) The “Found New Hardware” Wizard will appear. The first dialog should ask whether it is acceptable to use the Windows Update Service to find the device driver. Figure 3.2 – Found New Hardware Wizard 3) Select one of the “Yes” choices and click “Next”. Copyright © 2011 Future Technology Devices International Limited 12 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 4) The following screen appears: Figure 3.3 – Automatic Install 5) Wait while the driver is found, downloaded, and installed. This step may take a couple minutes depending on the Internet speed. 6) After the files are found and installed, click “Finish” to complete the installation. Figure 3.4 – Complete Hardware Installation 7) Steps 2 through 6 will repeat. The first time installs the basic USB Serial Converter in the USB device tree. The second time installs the Virtual COM Port layer in the Ports tree and assigns the COM port number. 8) When both portions of the device driver have been installed successfully, the following message will appear, indicating that the device is ready. Figure 3.5 – Hardware Ready Copyright © 2011 Future Technology Devices International Limited 13 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 COM Port Assignment Next, to determine which COM port has been assigned, open the Windows Device Manager from the System Control Panel. Figure 3.6 – Device Manager Click on the Plus “+” sign next to the Ports tree to list the available COM port. You will see “USB Serial Port”, followed by a COM assignment. In the figure below, the DB9-USB-RS232 module is assigned to COM3. Figure 3.7 – COM Port Assignment Use this COM port number with your application software in order to access the DB9-USB module. If an application requires use of a different COM port number, the assignment may be changed through the Advanced Driver Options settings. From the Device Manager listing above, right-click on the USB Serial Port and select Properties. Copyright © 2011 Future Technology Devices International Limited 14 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 Figure 3.8 – Access COM Port Properties Next, click on the “Port Settings” tab. Figure 3.9 – Settings Tab Then click on the “Advanced…” button. Copyright © 2011 Future Technology Devices International Limited 15 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 Figure 3.10 – Advanced Options This will display the various advanced settings. Note the COM port assignment in the upper left. Clicking on the drop-down list will display the available port numbers. Select one that is not in use and click OK on each dialog box to activate the selection. Windows will remember this COM port number. 4.1.2 Mac OS X, Linux, Windows CE Device drivers and FTDI installation guides for Mac OS X, Linux and Windows CE are available for download on the FTDI Chip web site. Follow the respective FTDI installation guides for the chosen operating system. Copyright © 2011 Future Technology Devices International Limited 16 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 5 Electrical details 5.1 USB Parameter Description Minimum Typical Maximum Units Conditions *Present when USB USB_VCC Input Power Voltage* 4.25 5.0* 5.25 V cable is attached and USB Host or Hub powered. Icc USB current 30 50 mA Table 5.1 – USB Electrical Details 5.2 RS232 Parameter Vtrans Vrec Description Transmitter output voltage swing Receiver input voltage range Minimum Typical Maximum ±5 ±2.4 ESD HBM ±25 ±15 Units Conditions V RL = 3KΩ V Input resistance = 3KΩ to 7KΩ KV RS-232 Inputs and Outputs Table 5.2 – RS232 Electrical Details 5.3 3.3V Level UART Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 2.2 2.7 3.2 V I source = 1mA Vol Output Voltage Low 0.3 0.4 0.5 V I sink = 2mA Vin Input Switching Threshold 1.0 1.2 1.5 V Vhys Input Switching Hysteresis 20 25 30 mV ** ** Table 5.3 – 3.3V Level UART Electrical Details 5.4 5V Level UART Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 3.2 4.1 4.9 V I source = 2mA Vol Output Voltage Low 0.3 0.4 0.6 V I sink = 2mA Vin Input Switching Threshold 1.0 1.2 1.5 V 20 25 30 mV Vhys Input Switching Hysteresis ** ** Table 5.4 – 5V Level UART Electrical Details Copyright © 2011 Future Technology Devices International Limited 17 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 6 Mechanical Details Figure 5.1 – DB9-USB dimensions Copyright © 2011 Future Technology Devices International Limited 18 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 7 Physical Environment Details 7.1 Storage Parameter T Description Storage Temperature Range Minimum Typical -65 Maximum +85 Units Conditions o C Table 7.1 – Storage Temperature 7.2 Operating Parameter T Description Operating Temperature Range Minimum –40 Typical Maximum +85 Units o C Conditions 5% to 95% RH, non condensing Table 7.2 – Operating Temperature Copyright © 2011 Future Technology Devices International Limited 19 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 8 Environmental Approvals & Declarations 8.1 EMI Compatibility FCC and CE DB9-USB modules are certified for both FCC Part 15 Subpart B and European EMC Directive. NOTE: This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. NOTE: This equipment is currently undergoing testing to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 8.2 Safety The DB9-USB modules are defined as Limited Power Supply (LPS) device, with operating voltages under 60VDC. 8.3 Environmental The DB9-USB modules are lead-free devices that comply with the following environmental directives: RoHS, WEEE, REACH, PFOS and DecaBDE. 8.4 Reliability The DB9-USB modules are designed to be a robust USB-Serial module for use in many environments. There are no user-serviceable parts. Any failure will require a replacement of the unit. Copyright © 2011 Future Technology Devices International Limited 20 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 8.5 Import / Export Information Import / Export Information Country of Origin Harmonized Code China 8.5.1.1 8471.80.4000 Product Description USB to Connector Adapter, Single Port USA ECCN EAR99 – No License Required Table 8.1 – Import / Export Information Copyright © 2011 Future Technology Devices International Limited 21 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 9 Troubleshooting Ensure the latest device driver is in use. See www.ftdichip.com If USB devices other than FTDI chips are installed in the system, then check with all manufacturers of these devices for the latest device drivers. Section 4 details driver installation. If the user continues to have driver installation issues, then please refer to the FTDI installation guides http://ftdichip.com/Documents/InstallGuides.htm for additional details. Common Windows Device Driver Troubles: DEVICE TIMES OUT: The default settings of the device driver assume typical data transfers of hundreds to thousands or more bytes at a given time. Some applications, such as a GPS device, only send data in short packets, often only a few bytes. If this is the case, it may be necessary to adjust the driver buffer size and/or latency timer to smaller values. These values can be adjusted through the Advanced driver options. The buffer size can be reduced to 64 bytes. The latency timer can be set as low as 2ms. A setting of 1ms will cause unnecessary USB traffic and could adversely affect data transmission. Advanced driver options are described in http://www.ftdichip.com/Documents/AppNotes/AN_107_AdvancedDriverOptions_AN_000073.pdf ERRATIC MOUSE POINTER: The device driver defaults to query an attached device to find out whether it is a mouse or modem, consistent with native COM port operation. Some RS232 peripherals constantly send short packets of data, causing the host system to “think” a mouse or modem has been attached. These short packets will interfere with normal mouse operation causing the pointer to jump around the screen. If this happens, disconnect the RS232 device and uncheck the Serial Enumerator option, also found on the Advanced driver options. COM PORT IN USE: Windows keeps track of all COM port assignments. If multiple FTDIChip products have been connected to a single system, the COM port number will increase, even if the other devices are not attached. If the higher COM port assignments are not acceptable for the application, known unused COM port numbers should be uninstalled according to the FTDI installation guide: http://ftdichip.com/Documents/InstallGuides.htm. Copyright © 2011 Future Technology Devices International Limited 22 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 10 Contact Information Head Office – Glasgow, UK Future Technology Devices International Limited Unit 1, 2 Seaward Place Centurion Business Park Glasgow, G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 E-mail (Sales) [email protected] E-mail (Support) [email protected] E-mail (General Enquiries) [email protected] Web Site URL http://www.ftdichip.com Web Shop URL http://www.ftdichip.com Branch Office – Shanghai, China Future Technology Devices International Limited (China) Room 408, 317 Xianxia Road, ChangNing District, ShangHai, China Tel: +86 (21) 62351596 Fax: +86(21) 62351595 E-Mail (Sales): [email protected] E-Mail (Support): [email protected] E-Mail (General Enquiries): [email protected] Web Site URL: http://www.ftdichip.com Branch Office – Taipei, Taiwan Future Technology Devices International Limited (Taiwan) 2F, No 516, Sec. 1 NeiHu Road Taipei 114 Taiwan, R.O.C. Tel: +886 (0) 2 8791 3570 Fax: +886 (0) 2 8791 3576 E-mail (Sales) [email protected] E-mail (Support) [email protected] E-mail (General Enquiries) [email protected] Web Site URL http://www.ftdichip.com Branch Office – Hillsboro, Oregon, USA Future Technology Devices International Limited (USA) 7235 NW Evergreen Parkway, Suite 600 Hillsboro, OR 97123-5803 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-Mail (Sales) [email protected] E-Mail (Support) [email protected] E-mail (General Enquiries) [email protected] Copyright © 2011 Future Technology Devices International Limited 23 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performance requirements. All application-related information in this document (including application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640. Copyright © 2011 Future Technology Devices International Limited 24 Document Reference No.: FT_000204 DB9-USB Datasheet Version 2.0 Clearance No.: FTDI# 130 Appendix A – References AN_149_Upgrading a DB9 RS232 Interface to USB using an FTDI DB9-USB-RS232 Module Appendix B – Revision History Version Draft First Draft October 2009 Version 1.0 First release 18th November 2009 Version 1.1 Updated part numbers 19th February 2010 Version 1.2 Added Figures 2.2 and 2.4. Updated tables 2.2 and 2.3 1st June 2010 Added note 1 to Table 2.2 Version 1.3 Simplified datasheet 5th November 2010 Version 2.0 Added details on Digital 3.3V and Digital 5V modules 31st August 2011 Edited descriptions Copyright © 2011 Future Technology Devices International Limited 25