Future Technology Devices International Ltd USB to RS232 UART Serial Converter PCB Datasheet Document Reference No.: FT_000079 Version 1.41 Issue Date: 2011-01-26 Future Technology Devices International Limited (FTDI) Unit1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH United Kingdom Tel.: +44 (0) 141 429 2777 Fax: + 44 (0) 141 429 2758 E-Mail (Support): [email protected] Web: http://www.ftdichip.com Copyright © 2011 Future Technology Devices International Limited Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit1, 2 Seaward Place, Centurion Business Park, Glasgow, G41 1HH, United Kingdom. Scotland Registered Number: SC136640 Copyright © 2011 Future Technology Devices International Limited Document Reference No.: FT_000079 USB TO RS232 UART SERIAL CONVERTER PCB Datasheet Version 1.41 Clearance No.: FTDI# 52 1 Description The USB-RS232-PCB is a USB to RS232 level serial UART converter PCB incorporating FTDI’s FT232RQ USB to Serial UART interface IC device which handles all the USB signalling and protocols. The PCB provides a fast, simple way to connect devices with a RS232 level serial interface to USB. Each USB-RS232-PCB contains a small internal electronic circuit board, utilising the FT232R plus a USB type-A connector. The FT232R datasheet, DS_FT232R, is available at http://www.ftdichip.com. The integrated electronics also include an RS232 level shifter plus Tx and Rx LEDs which give a visual indication of UART traffic. All components used, including the FT232R are Pb-free (RoHS compliant). The PCB is USB powered and USB 2.0 full speed compatible. Each PCB supports a data transfer rate up to 1 Mbaud and supports the FTDIChip-ID™, with a unique USB serial number programmed into the FT232R. This feature can be used to create a security or password protected file transfer access using the PCB. Further information and examples on this feature are available at http://www.ftdichip.com under FTDIChip-ID Projects. The USB-RS232-PCB requires USB drivers, available free from http://www.ftdichip.com, which are used to make the FT232R on the PCB appear as a virtual COM port (VCP). This then allows the user to communicate with the USB interface via a standard PC serial emulation port (for example TTY). Another FTDI USB driver, the D2XX driver, can also be used with application software to directly access the FT232R on the PCB though a DLL. This is illustrated in the Figure 1.1. VCP TTY USB-RS232-PCB USB RS232 UART SIGNALS Virtual COM Port D2XX DLL TTY USB-RS232-PCB USB RS232 UART SIGNALS Software application access to USB via D2XX Figure 1.1 Using the USB-RS232-PCB 1.1 Part Number The following Table 1.1 gives details of the available USB-RS232-PCB. Part Number Description USB-RS232-PCB USB to RS232 level UART PCB Table 1.1 USB-RS232-PCB Part Number Copyright © 2011 Future Technology Devices International Limited 1 Document Reference No.: FT_000079 USB TO RS232 UART SERIAL CONVERTER PCB Datasheet Version 1.41 Clearance No.: FTDI# 52 1.2 USB Compliant The USB-RS232-PCB is fully compliant with the USB 2.0 specification. Copyright © 2011 Future Technology Devices International Limited 2 Document Reference No.: FT_000079 USB TO RS232 UART SERIAL CONVERTER PCB Datasheet Version 1.41 Clearance No.: FTDI# 52 Table of Contents 1 Description ..................................................................................... 1 1.1 Part Number.................................................................................................. 1 1.2 USB Compliant .............................................................................................. 2 The USB-RS232-PCB is fully compliant with the USB 2.0 specification. ................... 2 2 Typical Applications ........................................................................ 4 2.1 Driver Support .............................................................................................. 4 2.2 Features ........................................................................................................ 5 3 Features of FT232R applicable to USB-RS232-PCB ......................... 6 4 USB-RS232-PCB Connector Pin Out and Mechanical details ............ 7 4.1 USB-RS232-PCB Signal Descriptions ............................................................. 9 4.2 USB-RS232-PCB +5V/+3.3V Selection .......................................................... 9 4.3 USB-RS232-PCB Electrical Parameters ........................................................ 10 5 USB-RS232-PCB Circuit Schematic ............................................... 11 6 Contact Information ..................................................................... 12 Appendix A - PCB EEPROM Configuration ........................................... 13 Appendix B - List of Figures and Tables.............................................. 14 Appendix C - Revision History ............................................................ 15 Copyright © 2011 Future Technology Devices International Limited 3 Document Reference No.: FT_000079 USB TO RS232 UART SERIAL CONVERTER PCB Datasheet Version 1.41 Clearance No.: FTDI# 52 2 Typical Applications USB to Serial RS232 Level Converter. USB Instrumentation PC interface. Upgrading Legacy Peripherals to USB. USB Industrial Control. Interface Microcontroller UART or I/O to USB. USB password protected file transfers. Interface FPGA / PLD to USB. 2.1 Driver Support Royalty free VIRTUAL COM PORT Royalty free D2XX Direct Drivers (VCP) DRIVERS for... (USB Drivers + DLL S/W Interface) Windows 98, 98SE, ME, 2000, Server 2003, XP and Server 2008 Windows 98, 98SE, ME, 2000, Server 2003, XP and Server 2008 Windows XP and XP 64-bit Windows XP and XP 64-bit Windows Vista and Vista 64-bit Windows Vista and Vista 64-bit Windows XP Embedded Windows XP Embedded Windows CE 4.2, 5.0 and 6.0 Windows CE 4.2, 5.0 and 6.0 Mac OS 8/9, OS-X Linux 2.4 and greater Linux 2.4 and greater Mac OS-X The drivers listed above are all available to download for free from www.ftdichip.com. Various 3rd Party Drivers are also available for various other operating systems - see www.ftdichip.com for details. Copyright © 2011 Future Technology Devices International Limited 4 Document Reference No.: FT_000079 USB TO RS232 UART SERIAL CONVERTER PCB Datasheet Version 1.41 Clearance No.: FTDI# 52 2.2 Features USB-RS232-PCB provides a USB to RS232 Serial UART interface. Support for FT232R FTDIChip-ID™ feature for improved security. Entire USB protocol handled by the electronics on the PCB. PCB is USB Powered - no external supply required. EIA/TIA-232 and V.28/V.24 communication interface with low power requirements. 6 outputs provide Tx, Rx, RTS#, CTS#, POWER and GND. UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no parity. Low USB bandwidth consumption. Fully assisted hardware (RTS#/CTS#) or X-On / X-Off software handshaking. Data transfer rates up to 1 Mbaud. Internal EEPROM with user writeable area. FTDI’s royalty-free VCP allow for communication as a standard emulated COM port and D2XX ‘direct’ drivers provide DLL application programming interface. UHCI / OHCI / EHCI host controller compatible. USB 2.0 Full Speed compatible. -40°C to +85°C operating temperature range. ESD Protection for RS-232 I/O's ±15kV Human Body Model (HBM) ±15kV EN61000-4-2 Air Gap Discharge ±8kV EN61000-4-2 Contact Discharge Copyright © 2011 Future Technology Devices International Limited 5 Document Reference No.: FT_000079 USB TO RS232 UART SERIAL CONVERTER PCB Datasheet Version 1.41 Clearance No.: FTDI# 52 3 Features of FT232R applicable to USB-RS232-PCB The USB-RS232-PCB uses FTDI’s FT232RQ USB to serial IC device. This section summarises the key features of the FT232RQ which apply to the USB-RS232-PCB. For further details, and a full features and enhancements description consult the FT232R datasheet, this is available from www.ftdichip.com. Internal EEPROM. The internal EEPROM is used to store USB Vendor ID (VID), Product ID (PID), device serial number, product description string and various other USB configuration descriptors. Each FT232RQ is supplied with the internal EEPROM pre-programmed as described in Appendix A - PCB EEPROM Configuration. The internal EEPROM descriptors can be programmed in circuit, over USB without any additional voltage requirement. It can be programmed using the FTDI utility software called MPROG, which can be downloaded from FTDI Utilities on the FTDI website (www.ftdichip.com). Additionally, there is a user area of the internal EEPROM available to system designers to allow storing of data (note that this is not modified by MPROG). Lower Operating and Suspend Current. The FT232R has a low 15mA operating supply current and a very low USB suspend current of approximately 70μA. Low USB Bandwidth Consumption. The USB interface of the FT232R, and therefore the USB-RS232PCB has been designed to use as little as possible of the total USB bandwidth available from the USB host controller. UART Pin Signal Inversion. The sense of each of the UART signals can be individually inverted by configuring options in the internal EEPROM. For example CTS# (active low) can be changed to CTS (active high), or TXD can be changed to TXD#. FTDIChip-ID™. The FT232R includes the new FTDIChip-ID™ security dongle feature. This FTDIChip-ID™ feature allows a unique number to be burnt into each FT_232RQ during manufacture. This number cannot be reprogrammed. This number is only readable over USB can be used to form the basis of a security dongle which can be used to protect any customer application software being copied. This allows the possibility of using the USB-RS232-PCB as a dongle for software licensing. Further to this, a renewable license scheme can be implemented based on the FTDIChip-ID™ number when encrypted with other information. This encrypted number can be stored in the user area of the FT232R internal EEPROM, and can be decrypted, then compared with the protected FTDIChip-ID™ to verify that a license is valid. Web based applications can be used to maintain product licensing this way. An application note, AN232R-02, available from FTDI website (www.ftdichip.com) describes this feature. Extended Operating Temperature Range - The USB-RS232-PCB is capable of operating over an extended temperature range of -40º to +85ºC thus allowing it to be used in automotive or industrial applications. Copyright © 2011 Future Technology Devices International Limited 6 Document Reference No.: FT_000079 USB TO RS232 UART SERIAL CONVERTER PCB Datasheet Version 1.41 Clearance No.: FTDI# 52 4 USB-RS232-PCB Connector Pin Out and Mechanical details GRN LED RED LED RTS Level SHIFTER POWER Rx CTS GND FT232R Tx USB-RS232-PCB Rev 1 GRN LED RED LED Tx Level SHIFTER GND CTS RTS FT232R POWER Rx USB-RS232-PCB Rev 2 Figure 4.1 USB-RS232-PCB Pin Out (Top is TOP View, Bottom is BOTTOM View) Changes made from Rev1 to Rev 2 design: - Pad designation changed between Rev1 and Rev2 (see Figure 4.1) R1 doesn’t exist in Rev2 design, the selection of power signal is done using either R2 (+3.3V) or R3 (+5V), (see Table 4.2) The LEDTX, LEDRX, PWREN and SLEEP are connected to the FT232R differently (see schematic) The mechanical details of the PCB are shown in the following diagram Figure 4.2 Copyright © 2011 Future Technology Devices International Limited 7 Document Reference No.: FT_000079 USB TO RS232 UART SERIAL CONVERTER PCB Datasheet Version 1.41 Clearance No.: FTDI# 52 24.9 +/- 0.4 11.85 +/- 0.35 1.6 11.85 +/- 0.35 40.1 +/- 0.2 4.9 +/- 0.1 4.5 +/- 0.01 18.8 +/- 0.2 Dimensions in mm Figure 4.2 USB-RS232-PCB, Mechanical Details Copyright © 2011 Future Technology Devices International Limited 8 Document Reference No.: FT_000079 USB TO RS232 UART SERIAL CONVERTER PCB Datasheet Version 1.41 Clearance No.: FTDI# 52 4.1 USB-RS232-PCB Signal Descriptions Name Type Description GND GND Device ground supply pin. CTS# Input Clear to Send Control input / Handshake signal. Power output. Default is GND, but can be customised to POWER Output output +3.3V or +5V. If required, contact FTDI Sales Team ([email protected]) TXD Output RXD Input RTS# Output Transmit Asynchronous Data output. Receive Asynchronous Data input. Request To Send Control Output / Handshake signal. Table 4.1 USB-RS232-PCB Signal Descriptions 4.2 USB-RS232-PCB +5V/+3.3V Selection Selection of whether the POWER signal is GND, +3.3V or +5V is done using resistors. The following table gives details of what resistors are required for the different voltage levels. Resistor Resistor R2 R3 Not Not Fitted Fitted Fitted Not Fitted Not Fitted Fitted Description VCC floats POWER Signal is +3.3V POWER Signal is +5.0V Table 4.2 UART Signal Level Selection Copyright © 2011 Future Technology Devices International Limited 9 Document Reference No.: FT_000079 USB TO RS232 UART SERIAL CONVERTER PCB Datasheet Version 1.41 Clearance No.: FTDI# 52 4.3 USB-RS232-PCB Electrical Parameters Parameter Description Minimum Typical Maximum Units Conditions *Default is GND. This figure only applies when cable has been customised to output VCC_5V Output Power Voltage* 4.25 5.0* 5.25 V +5V. The range is dependent on the USB port that the USB-RS232-WE is connected to **Default is GND. This VCC_3.3V Output Power Voltage** 3.2 3.3** 3.4 V figure only applies when cable has been customised to output +3.3V. ***Only applies when POWER output is customised IO Output Power Current*** - 75 mA to +5V or+3.3V Must be less that 2.5mA during suspend. T Operating Temperature -40 Range o +85 C Table 4.3 USB-RS232-PCB Parameter Vtrans Vrec Description Minimum Typical Maximum Units +/- 5 +/- 6.5 +/- 15 V +25 V RS232 Transmitter output voltage swing RS232 Receiver input -25 voltage range Conditions Table 4.4 USB-RS232-PCB I/O Pin Characteristics Description Conditions Minimum Typical ESD HBM RS-232 Inputs and Outputs ±15 kV EN61000-4-2ContactDischarge RS-232 Inputs and Outputs ±8 kV EN61000-4-2AirGapDischarge RS-232 Inputs and Outputs ±15 kV Maximum Table 4.5 USB-RS232-WE ESD Tolerance Copyright © 2011 Future Technology Devices International Limited 10 Document Reference No.: FT_000079 USB TO RS232 UART SERIAL CONVERTER PCB Datasheet Version 1.41 Clearance No.: FTDI# 52 5 USB-RS232-PCB Circuit Schematic The circuit schematic of the USB-RS232-PCB, utilising the FTDI FT232R, is shown in Figure 5.1 Figure 5.1 Circuit Schematic of USB-RS232-PCB. Copyright © 2011 Future Technology Devices International Limited 11 Document Reference No.: FT_000079 USB TO RS232 UART SERIAL CONVERTER PCB Datasheet Version 1.41 Clearance No.: FTDI# 52 6 Contact Information Head Office – Glasgow, UK Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) Web Site URL Web Shop URL [email protected] [email protected] [email protected] http://www.ftdichip.com http://www.ftdichip.com Branch Office – Taipei, Taiwan Future Technology Devices International Limited (Taiwan) 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8791 3570 Fax: +886 (0) 2 8791 3576 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) Web Site URL [email protected] [email protected] [email protected] http://www.ftdichip.com Branch Office – Hillsboro, Oregon, USA Future Technology Devices International Limited (USA) 7235 NW Evergreen Parkway, Suite 600 Hillsboro, OR 97123-5803 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-Mail (Sales) E-Mail (Support) E-Mail (General Enquiries) Web Site URL [email protected] [email protected] [email protected] http://www.ftdichip.com Branch Office – Shanghai, China Future Technology Devices International Limited (China) Room 408, 317 Xianxia Road, Shanghai, 200051 China Tel: +86 21 62351596 Fax: +86 21 62351595 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) Web Site URL [email protected] [email protected] [email protected] http://www.ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. Copyright © 2011 Future Technology Devices International Limited 12 Document Reference No.: FT_000079 USB TO RS232 UART SERIAL CONVERTER PCB Datasheet Version 1.41 Clearance No.: FTDI# 52 Appendix A - PCB EEPROM Configuration Each USB-RS232-PCB is controlled by the FTDI FT232R IC. This FT232R device contains an EEPROM which contains the USB configuration descriptors for that device. When the PCB is plugged into a PC or a USB reset is performed, the PC will read these descriptors. The default values stored into the internal EEPROM are defined in Table 0.1 Default Internal EEPROM Configuration Parameter Value USB Vendor ID (VID) 0403h FTDI default VID (hex) USB Product UD (PID) 6001h FTDI default PID (hex) Serial Number Enabled? Serial Number Pull down I/O Pins in USB Suspend Yes See Note A unique serial number is generated and programmed into the EEPROM during device final test. Disabled Enabling this option will make the device pull down on the UART interface lines when the power is shut off (PWREN# is high). Manufacturer Name FTDI Product Description See note Max Bus Power Current Power Source Device Type USB Version Notes USB-RS232-PCB 90mA Bus Powered FT232R 0200 Returns USB 2.0 device description to the host. Note: The device is be a USB 2.0 Full Speed device (12Mb/s) as opposed to a USB 2.0 High Speed device (480Mb/s). Remote Wake Up Disabled High Current I/Os Enabled Load VCP Driver Enabled Invert TXD Disabled Signal on this pin becomes TXD# if enable. Invert RXD Disabled Signal on this pin becomes RXD# if enable. Invert RTS# Disabled Signal on this pin becomes RTS if enable. Invert CTS# Disabled Signal on this pin becomes CTS if enable. Enables the high drive level on the UART and CBUS I/O pins. Makes the device load the VCP driver interface for the device. Table 0.1 Default Internal EEPROM Configuration The internal EEPROM on the PCB can be re-programmed over USB using the utility program MPROG. MPROG can be downloaded from the www.ftdichip.com. Version 2.8a or later is required for the FT232R chip. Users who do not have their own USB Vendor ID but who would like to use a unique Product ID in their design can apply to FTDI for a free block of unique PIDs. Contact FTDI support for this service. Copyright © 2011 Future Technology Devices International Limited 13 Document Reference No.: FT_000079 USB TO RS232 UART SERIAL CONVERTER PCB Datasheet Version 1.41 Clearance No.: FTDI# 52 Appendix B - List of Figures and Tables List of Figures Figure 1.1 Using the USB-RS232-PCB .............................................................................. 1 Figure 4.1 USB-RS232-PCB Pin Out (Top is TOP View, Bottom is BOTTOM View) .................... 7 Figure 4.2 USB-RS232-PCB, Mechanical Details ................................................................. 8 Figure 5.1 Circuit Schematic of USB-RS232-PCB. ............................................................. 11 List of Tables Table 1.1 USB-RS232-PCB Part Number ........................................................................... 1 Table 4.1 USB-RS232-PCB Signal Descriptions .................................................................. 9 Table 4.2 UART Signal Level Selection .............................................................................. 9 Table 4.3 USB-RS232-PCB ............................................................................................ 10 Table 4.4 USB-RS232-PCB I/O Pin Characteristics ........................................................... 10 Table 4.5 USB-RS232-WE ESD Tolerance........................................................................ 10 Table 0.1 Default Internal EEPROM Configuration ............................................................ 13 Copyright © 2011 Future Technology Devices International Limited 14 Document Reference No.: FT_000079 USB TO RS232 UART SERIAL CONVERTER PCB Datasheet Version 1.41 Clearance No.: FTDI# 52 Appendix C - Revision History Version Draft First Draft August 2008 Version 1.0 First Release September 12th 2008 Version 1.1 Update to Taiwan address October 1st 2008 Version 1.2 Update to UK and CH address February 11th 2009 Version 1.3 Update to PCB drawings to show REV1 and REV2 April 13th 2009 Version 1.4 Update figure 5.1 – Schematic Updated section 4 (changes made from Rev1 to rev2) Updated contact information May 28th 2010 Version 1.41 Added the RoHs compliant statement in section 1 January 26th 2011 Added section 1.2 USB compliant Logo Copyright © 2011 Future Technology Devices International Limited 15