Future Technology Devices International Ltd USB-COM485-PLUS4 Datasheet Document Reference No.: FT_000153 Version 1.2 Issue Date: 2010-04-12 Future Technology Devices International Ltd (FTDI) Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow, G41 1HH, United Kingdom Tel.: +44 (0) 141 429 2777 Fax: + 44 (0) 141 429 2758 E-Mail (Support): [email protected] Web: http://www.ftdichip.com Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit1, 2 Seaward Place, Centurion Business Park, Glasgow, G41 1HH, United Kingdom. Scotland Registered Number: SC136640 Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 1 Introduction 1.1 Functional Description The USB-COM485-PLUS4 is a USB to a quad interface RS485 level serial UART adaptor incorporating FTDI’s FT4232H Hi-Speed USB2.0 (480Mb/s) to quad serial UART interface IC device. The FT4232H handles all the USB signalling and protocols. The adaptor provides a fast, simple way to connect devices with an RS485 interface to USB. USB-COM485-PLUS4 is a USB to a quad-port RS485 adapter. The integrated electronics of the USB-COM485-PLUS4 utilise the FTDI FT2232H and includes RS485 level shifters plus TXD/RXD LEDs to provide a visual indication of data traffic through the module. Figure 1.1 USB-COM485-PLUS4 The module uses a standard USB mini-B device connector for connection to an upstream host or hub port. RS485-level signals are available on an industry-standard DE-9P connector. The maximum RS485level data rate is 10Mbps. The USB-COM485-PLUS4 module requires USB device drivers, available free from www.ftdichip.com, which are used to make the USB-COM485-PLUS4 appear as a Virtual COM Port (VCP). This allows existing serial communications software, such as HyperTerminal, to exchange data through the USB-COM485PLUS4 to a legacy RS485 peripheral device. Copyright © 2010 Future Technology Devices International Limited 1 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 1.2 LED Description The USB-COM485-PLUS4 uses 9 LEDs to indicate a valid link as well as data traffic according to the following table: LED Colour Function Description Yellow x 1 Power Red x 4 TxD Activity Flashes when data is transmitted from the USB-COM485-PLUS4 to the attached RS485 device Green x 4 RxD Activity Flashes when data is transmitted from the attached RS485 device to the USB-COM485-PLUS4 ON when USB-COM485-PLUS4 is configured and ready Table 1.1 – LED Description Copyright © 2010 Future Technology Devices International Limited 2 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 1.3 Block Diagram Channel A Channel B USB miniB Client Connector RS485 Level Shifter DE-9P Connector A RS485 Level Shifter DE-9P Connector B RS485 Level Shifter DE-9P Connector C RS485 Level Shifter DE-9P Connector D FTDI FT4232H High-Speed USB Serial Bridge Channel D Channel C Figure 1.2 USB-COM485-PLUS4 Block Diagram 1.3.1 Block description USB Mini B Client Connector This connector provides the interface for connection to a USB Host or Hub port. The maximum cable length is 5 meters, according to the USB 2.0 specification. FTDI FT4232H FT4232H Hi-Speed USB2.0 (480Mb/s) is a quad serial UART interface IC device. Operating system device drivers are required in order to operate with the FT4232H in order to provide the Virtual COM Port serial functionality. Quad RS485 Level Shifter The RS485 level shifter converts the signals provided by the FT4232H into the voltage levels required by RS485 devices. DE-9P Connector (Male) The DE-9P connectors are configured in an industry standard (TIA/EIA-574) pin-out to provide connection to RS485 peripherals through standard cables. See section 3.1.2 Copyright © 2010 Future Technology Devices International Limited 3 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 1.4 Features Adds four RS-485 serial ports by connecting to a USB 2.0 Hi-Speed interface. Easy plug & play installation and RS-485 device connection Operates with USB 1.1 & 2.0 Host and Hub ports Industry Standard FTDI chip set & device drivers for maximum compatibility Microsoft Windows® WHQL-certified, Mac OS X, Linux and Windows CE device drivers Installs as a standard Windows COM ports COM port number can be changed to any available COM port number, to support HyperTerminal, or any other serial communications software application running in Windows Supports Windows Server 2008, 2003, Vista, XP, 2000, Windows CE, Linux, Mac OS X FIFO: 2K byte transmit buffer, 2K byte receive buffer RS-485 data signals: Data+, Data-, GND Powered by USB port. No external power adapter required. +5V output available. Serial port speed up to 10Mbps Serial Communication Parameters o Parity: None, Even, Odd o Data bits: 7, 8 o Flow control: X-ON/X-OFF, None Four DE-9P male connectors LEDs indicate USB Enumeration, RxD, TxD for monitoring port status & easy diagnostics Operating temperature of -40°C to +85°C Echo and non-Echo two modes can be selected. 1.5 Performance Figures Parameter Performance USB Interface 480Mbps USB 2.0 High-Speed Standard Windows baud rates (300bps to 921.6Kbps) RS485 Interface Custom baud rates (300bps to 10Mbps) through baud rate aliasing. See FTDI Application Note: Configuring FT232R, FT2232 and FT232BM Baud Rates Max Cable Length USB = 5m, RS485 =12m (at 10Mbps) Table 1.2 - Performance Figures Part Number Description USB-COM485-PLUS4 USB-COM-Plus Hi-Speed USB to 4-Port RS485 module Table 1.3 - Ordering Information Copyright © 2010 Future Technology Devices International Limited 4 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 1 Introduction ................................................................................... 1 1.1 Functional Description .................................................................................. 1 1.2 LED Description ............................................................................................. 2 1.3 Block Diagram ............................................................................................... 3 1.3.1 2 1.4 Features ........................................................................................................ 4 1.5 Performance Figures ..................................................................................... 4 Installation ..................................................................................... 7 2.1 Example Applications and Configurations ..................................................... 7 2.1.1 2.2 3 5 7 Device Driver Installation ............................................................................. 9 Microsoft Windows ..................................................................................... 9 2.2.2 Mac OS X, Linux, Windows CE ................................................................... 14 Connections .................................................................................. 15 External Connectors .................................................................................... 15 3.1.1 USB ....................................................................................................... 15 3.1.2 RS485 .................................................................................................... 15 Electrical details ........................................................................... 16 4.1 USB ............................................................................................................. 16 4.2 RS485 ......................................................................................................... 16 4.3 Power Output .............................................................................................. 16 Mechanical Details ........................................................................ 17 5.1 6 Module Mechanical Dimensions ................................................................... 17 Physical Environment Details ....................................................... 18 6.1 Storage ....................................................................................................... 18 6.2 Operating .................................................................................................... 18 Environmental Approvals & Declarations ...................................... 19 7.1 EMI Compatibility ........................................................................................ 19 7.2 Safety.......................................................................................................... 19 7.3 Environmental ............................................................................................. 19 7.4 Reliability .................................................................................................... 19 7.4.1 7.5 8 9 Wiring ...................................................................................................... 7 2.2.1 3.1 4 Block description ....................................................................................... 3 MTTF ..................................................................................................... 19 Import / Export Information ....................................................................... 20 Troubleshooting ........................................................................... 21 8.1 Hardware .................................................................................................... 21 8.2 Device Driver .............................................................................................. 21 Contact Information ..................................................................... 22 Copyright © 2010 Future Technology Devices International Limited 5 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 10 Appendix A - List of Figures and tables......................................... 24 Appendix B - Revision History ............................................................ 25 Copyright © 2010 Future Technology Devices International Limited 6 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 2 Installation 2.1 Example Applications and Configurations 2.1.1 Wiring Insert the A-plug into an available USB Host or Hub port. Insert the mini B-plug into the mini Breceptacle on the USB-COM485-PLUS4. DTE Pin Number 1 Expected Connect Signal Signal Name DATA- = Transmit/Receive Data, negative polarity Also Terminator 2 DATAPin 2 of 120R Terminating Resistor. Only Required if the USBCOM485-PLUS4 is the first or last device in a multi-drop RS485 System, to meet RS485 Termination Requirements. 2 DATA+ = Transmit/Receive DATA+ Data, positive polarity 3 Terminator 1 Pin 1 of 120R Terminating Resistor. Only Required if the USBCOM485-PLUS4 is the first or last device in a multi-drop RS485 System, to meet RS485 Termination Requirements. 4 N/A N/A 5 GND = signal ground GND 6 N/A N/A 7 echo disable terminal 1 Local echo function control. Connect pin7 and pin 8 can disable the local echo function. The local echo is enabled by default. 8 echo disable terminal 2 Local echo function control. Connect pin7 and pin 8 can disable the local echo function. The local echo is enabled by default. 9 PWR = +5V DC output PWR Table 2.1 – RS485 DTE to DCE connection Figure 2.1 USB-COM485-PLUS4 Termination resistor. Copyright © 2010 Future Technology Devices International Limited 7 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 Figure 2.2 USB-COM485-PLUS4 echo disable Copyright © 2010 Future Technology Devices International Limited 8 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 2.2 Device Driver Installation The USB-COM485-PLUS4 module drivers are available for download from: www.ftdichip.com 2.2.1 Microsoft Windows With the device drivers being Windows Hardware Quality Labs (WHQL) certified, they are also available through download directly from the Microsoft® Windows® Update service. This is the best choice when connecting the USB-COM485-PLUS4 to a computer running Windows Vista. Additional installation options are noted below: Installation Executable shown on Windows XP 1) Login to your system as Administrator, or a user with Administrator rights. 2) Prior to connecting the USB-COM485-PLUS4 to the USB Host or Hub port, download the latest device driver version from the FTDIChip web site. 3) Run this executable to install the device drivers. 4) Connect the USB-COM485-PLUS4 to your computer. A notification will appear near the task bar indicating that new hardware has been installed and is ready for use. It is normal if this notice appears twice. Figure 2.3 - Hardware Ready Windows Update shown on Windows XP You must have an active Internet connection and the Windows Update Service enabled. 1) Connect the USB-COM485-PLUS4 to your USB Host or Hub. 2) The “Found New Hardware” Wizard will appear. The first dialog should ask whether it is acceptable to use the Windows Update Service to find the device driver. Figure 2.4 – Found New Hardware Wizard 3) Select one of the “Yes” choices and click “Next”. 4) The following screen appears: Copyright © 2010 Future Technology Devices International Limited 9 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 Figure 2.5 – Automatic Install 5) Wait while the driver is found, downloaded, and installed. This step may take a couple minutes. 6) After the files are found and installed, click “Finish” to complete the installation. Figure 2.6 - Complete Hardware Installation 7) Steps 2 through 6 will repeat. The first time installs the basic USB Serial Converter in the USB device tree. The second time installs the Virtual COM Port layer in the Ports tree and assigns the COM port number. You must install the Virtual COM Port layer four times, because the USBCOM485-Plus4 has four Virtual COM Ports. 8) When both portions of the device driver have been installed successfully, the following message will appear, indicating that the device is ready. Copyright © 2010 Future Technology Devices International Limited 10 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 Figure 2.7 - Hardware Ready COM Port Assignment Next, to determine which COM port has been assigned, open the Windows Device Manager from the System Control Panel. Figure 2.8 - Device Manager Click on the Plus “+” sign next to the Ports tree and Universal Serial Bus controllers tree to list the available USB device. You will see four additional “USB Serial Port”, followed by a COMn assignment. And four additional “USB Serial Converter A” ,“USB Serial Converter B” ,“USB Serial Converter C” and “USB Serial Converter D”. Figure 2.9 - COM Port and USB Device name Assignment Copyright © 2010 Future Technology Devices International Limited 11 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 To determine which COM port has been assigned to Converter A, B, C or D, the cursor point to the USB Serial Port (COM5), (COM6), (COM7), (COM8), then right-click on it and select “Properties”, it shows their relationship to the Converter A, B, C or D. In the figure below, the Converter A is assigned to COM5, Converter B is assigned to COM6, Converter C is assigned to COM7 and Converter D is assigned to COM8. Figure 2.10 – COM Port Assignment and Proterties Use this COM port number with your application software in order to access the USB-COM485-PLUS4. If an application requires use of a different COM port number, the assignment may be changed through the Advanced Driver Options settings. From the above “Properties”, click on the “Port Settings” tab. Copyright © 2010 Future Technology Devices International Limited 12 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 Figure 2.11 - Settings Tab Then click on the “Advanced…” button. Figure 2.12 - Advanced Options This will display the various advanced settings. Note the COM port assignment in the upper left. Clicking on the drop-down list will display the available port numbers. Select one that is not in use and click OK on each dialog box to activate the selection. Windows will remember this COM port number. Copyright © 2010 Future Technology Devices International Limited 13 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 2.2.2 Mac OS X, Linux, Windows CE Device drivers and FTDI installation guides for Mac OS X, Linux and Windows CE are available for download on the FTDIChip web sites. Follow the respective FTDI installation guides for the chosen operating system. Copyright © 2010 Future Technology Devices International Limited 14 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 3 Connections 3.1 External Connectors 3.1.1 USB The USB-COM485-PLUS4 is a downstream USB 2.0 Device. A standard USB “mini B” receptacle is mounted inside the USB-COM485-PLUS4 to facilitate connection to an upstream USB Host or Hub. Pin Number Pin Type Description 1 Power 2 Bidirectional D– = USB data signal, negative polarity 3 Bidirectional D+ = USB data signal, positive polarity 4 ID 5 Ground Shield Case Ground VBUS = USB Power provided from upstream USB Host or Hub No connected GND = USB signal ground Drain = typically connected to the host PC case Table 3.1 – USB " mini B" Receptacle Pin-Out 3.1.2 RS485 The RS485 ports are configured as Data Terminal Equipment (DTE), with a 9-contact D-Sub Pin connector. Pin assignments are according to TIA/EIA-485. In addition, pin9 of DB9 provides +5VDC to an external device with a maximum current draw of 450mA once the USB-COM485-PLUS4 has been enumerated by the system. Pin Number Pin Type 1 Description DATA- Input/Output Pin 2 of 120R Terminating Resistor. Only Required if the USBCOM485-PLUS4 is the first or last device in a multi-drop RS485 System, to meet RS485 Termination Requirements. 2 Input/Output DATA+ 3 Input Pin 1 of 120R Terminating Resistor. Only Required if the USBCOM485-PLUS4 is the first or last device in a multi-drop RS485 System, to meet RS485 Termination Requirements. 4 N/A N/A 5 GND = signal ground GND 6 N/A N/A 7 Input Local echo function control input pin. Connect pin7 and pin 8 can disable the local echo function. The local echo is enabled by default. 8 Output Local echo function control output pin. Connect pin7 and pin 8 can disable the local echo function. The local echo is enabled by default. 9 PWR = +5V DC output PWR Table 3.2 – DE-9P RS485 Pin-Out Copyright © 2010 Future Technology Devices International Limited 15 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 4 Electrical details 4.1 USB Parameter Description Minimum Typical Maximum Units Conditions *Present when USB USB_VCC Input Power Voltage* 4.25 5.0* 5.25 V cable is attached and USB Host or Hub powered. ***Does not include Icc USB current*** 30 50 mA power supplied to external device connected to pin 9 Table 4.1 - USB Electrical Details 4.2 RS485 Parameter Vtrans Vrec ESD HBM Description Transmitter output voltage swing Receiver input voltage range Minimum Typical Maximum 2 -7 N/A +12 ±15 Units Conditions V RL = 50R CL = 50pF V RL = 50R CL = 50pF KV For all RS-485 Inputs and Outputs pin Table 4.2 – RS485 Electrical Details 4.3 Power Output The USB-COM485-PLUS4 provides +5V DC for an external device that requires power on pin9 of DB9. The maximum allowable current is 500mA, including the circuitry of the USB-COM485-PLUS4 itself. Up to 250mA (total output on all 4 ports) may be used by the external device. The +5V output is only enabled when the USB interface is not in suspend. Parameter Description Minimum Typical Maximum Units Conditions USB interface is not in IO Output Power Current 0 250 mA SUSPEND. This is the total current available on all 4 ports Table 4.3 - Power Output for USB-COM485-PLUS4 Copyright © 2010 Future Technology Devices International Limited 16 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 5 Mechanical Details 5.1 Module Mechanical Dimensions Dimensions are in mm. The height of the module is dominated by the 4 D-type connectors and stands 12.8mm +/- 1mm. The D-type pins protrude below the PCB by 2.54mm +/-1mm Figure 5.1 - USB-COM485-PLUS4 PCB Dimensions Copyright © 2010 Future Technology Devices International Limited 17 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 6 Physical Environment Details 6.1 Storage Parameter T Description Minimum Storage Temperature Range Typical -65 Maximum +150 Units Conditions o C Table 6.1 - Storage Temperature 6.2 Operating Parameter T Description Minimum Operating Temperature Range –40 Typical Maximum +85 Units o C Conditions 5% to 95% RH, non condensing Table 6.2 - Operating Temperature Copyright © 2010 Future Technology Devices International Limited 18 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 7 Environmental Approvals & Declarations 7.1 EMI Compatibility FCC and CE The USB-COM485-PLUS4 has been tested to be compliant with both FCC Part 15 Subpart B and European EMC Directive. NOTE: This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 7.2 Safety The USB-COM485-PLUS4 is defined as Limited Power Supply (LPS) device, with operating voltages under 60VDC. 7.3 Environmental The USB-COM485-PLUS4 is a lead-free device that complies with the following environmental directives: RoHS, WEEE, REACH, PFOS and DecaBDE. 7.4 Reliability The USB-COM485-PLUS4 is designed as a robust USB-Serial module for use in many environments. There are no user-serviceable parts. Any failure will require a replacement of the unit. 7.4.1 MTTF The Mean Time To Failure is calculated at TBD hours. Copyright © 2010 Future Technology Devices International Limited 19 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 7.5 Import / Export Information Import / Export Information Country of Origin China Harmonized Code TBD Product Description USB to RS485 Development Module, Four COM PortS USA ECCN EAR99 – No License Required Table 7.1 - Import / Export Information Copyright © 2010 Future Technology Devices International Limited 20 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 8 Troubleshooting 8.1 Hardware Cables are the most common sources of trouble with external devices. Check the following: - USB cable is properly inserted at both ends - Computer power is ON - Computer is not in Sleep or Standby - If a USB Hub is used, be sure it is set for “Self-Powered” operation - If a USB Hub is used, be sure all cables are properly inserted - If all the above are OK, the Yellow LED should be lit, indicating the device has been recognized by the USB subsystem. RS485 cables – check the following: - Check for specific handshake requirements of your RS485 peripheral. - Because there is not handshake signals, ensure the application is set to “No Hardware Handshake”, or equivalent. - Test the port with a loop-back connector. Connect DATA+ to DATA+, DATA- to DATA-. Use a simple terminal program to check that data is transmitted and received. 8.2 Device Driver Ensure the latest device driver is in use. See www.ftdichip.com If other devices with FTDI chips are installed in the system, check with all manufacturers of these devices for the latest device drivers. See the FTDI installation guides for additional details: http://ftdichip.com/Documents/InstallGuides.htm Common Windows Device Driver Troubles: DEVICE TIMES OUT: The default settings of the device driver assume typical data transfers of hundreds to thousands or more bytes at a given time. Some applications, such as a GPS device, only send data in short packets, often only a few bytes. If this is the case, it may be necessary to adjust the driver buffer size and/or latency timer to smaller values. These values can be adjusted through the Advanced driver options as noted in Figure 2.13. The buffer size can be reduced to 64 bytes. The latency timer can be set as low as 2ms. A setting of 1ms will cause unnecessary USB traffic and could adversely affect data transmission. ERRATIC MOUSE POINTER: The device driver defaults to query an attached device to find out whether it is a mouse or modem, consistent with native COM port operation. Some RS485 peripherals constantly send short packets of data, causing the host system to “think” a mouse or modem has been attached. These short packets will interfere with normal mouse operation causing the pointer to jump around the screen. If this happens, disconnect the RS485 device and uncheck the Serial Enumerator option, also found on the Advanced driver options screen in Figure 2.13. COM PORT IN USE: Windows keeps track of all COM port assignments. If multiple FTDIChip products have been connected to a single system, the COM port number will increase, even if the other devices are not attached. If the higher COM port assignments are not acceptable for the application, known unused COM port numbers should be uninstalled according to the FTDI installation guide: http://ftdichip.com/Documents/InstallGuides.htm. Copyright © 2010 Future Technology Devices International Limited 21 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 9 Contact Information Head Office – Glasgow, UK Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 E-mail (Sales) [email protected] E-mail (Support) [email protected] E-mail (General Enquiries) [email protected] Web Site URL http://www.ftdichip.com Web Shop URL http://www.ftdichip.com Branch Office – Taipei, Taiwan Future Technology Devices International Limited (Taiwan) 2F, No 516, Sec. 1 NeiHu Road Neihu District Taipei 114 Taiwan, R.O.C. Tel: +886 (02) 8797 1330 Fax: +886 (02) 8751 9737 E-mail (Sales) [email protected] E-mail (Support) [email protected] E-mail (General Enquiries) [email protected] Web Site URL http://www.ftdichip.com Branch Office – Shanghai, China Future Technology Devices International Limited (China) Room 408, 317 Xianxia Road, ChangNing District, ShangHai, China Tel: +86 (21) 62351596 Fax: +86(21) 62351595 E-Mail (Sales): [email protected] E-Mail (Support): [email protected] E-Mail (General Enquiries): [email protected] Web Site URL: http://www.ftdichip.com Branch Office – Hillsboro, Oregon, USA Future Technology Devices International Limited (USA) 7235 NW Evergreen Parkway, Suite 600 Hillsboro, OR 97123-5803 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-Mail (Sales) [email protected] E-Mail (Support) [email protected] E-mail (General Enquiries) [email protected] Web Site URL http://www.ftdichip.com Copyright © 2010 Future Technology Devices International Limited 22 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. Copyright © 2010 Future Technology Devices International Limited 23 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 10 Appendix A - List of Figures and tables List of Figures: Figure 1.1 USB-COM485-PLUS4 ..................................................................................................................... 1 Figure 1.2 USB-COM485-PLUS4 Block Diagram .......................................................................................... 3 Figure 2.1 USB-COM485-PLUS4 Termination resistor................................................................................. 7 Figure 2.2 USB-COM485-PLUS4 echo disable .............................................................................................. 8 Figure 2.3 - Hardware Ready .......................................................................................................................... 9 Figure 2.4 – Found New Hardware Wizard .................................................................................................... 9 Figure 2.5 – Automatic Install ....................................................................................................................... 10 Figure 2.6 - Complete Hardware Installation .............................................................................................. 10 Figure 2.7 - Hardware Ready ........................................................................................................................ 11 Figure 2.8 - Device Manager ......................................................................................................................... 11 Figure 2.9 - COM Port and USB Device name Assignment ....................................................................... 11 Figure 2.10 – COM Port Assignment and Proterties .................................................................................. 12 Figure 2.11 - Settings Tab ............................................................................................................................. 13 Figure 2.12 - Advanced Options ................................................................................................................... 13 Figure 5.1 - USB-COM485-PLUS4 PCB Dimensions .................................................................................. 17 List of tables: Table 1.1 – LED Description ........................................................................................................................... 2 Table 1.2 - Performance Figures .................................................................................................................... 4 Table 1.3 - Ordering Information .................................................................................................................... 4 Table 2.1 – RS485 DTE to DCE connection ................................................................................................... 7 Table 3.1 – USB " mini B" Receptacle Pin-Out ........................................................................................... 15 Table 3.2 – DE-9P RS485 Pin-Out ................................................................................................................. 15 Table 4.1 - USB Electrical Details ................................................................................................................. 16 Table 4.2 – RS485 Electrical Details ............................................................................................................ 16 Table 4.3 - Power Output for USB-COM485-PLUS4 ................................................................................... 16 Table 6.1 - Storage Temperature .................................................................................................................. 18 Table 6.2 - Operating Temperature .............................................................................................................. 18 Table 7.1 - Import / Export Information ........................................................................................................ 20 Copyright © 2010 Future Technology Devices International Limited 24 Document Reference No.: FT_000153 USB-COM485-PLUS4 Datasheet Version 1.2 Clearance No.: FTDI# 108 Appendix B - Revision History Version 1.0 First release Version 1.1 Modified the description of Echo function Version 1.2 Edited Section 1.3.1, Removed the statement “A standard “A to B” cable is provided” 14th September 2009 24th January 2010 12th April 2010 Copyright © 2010 Future Technology Devices International Limited 25