Future Technology Devices International Ltd. USB Hi-Speed Serial/Hub Module Datasheet Document Reference No.: FT_000331 Version 1.2 Issue Date: 2010-10-28 Future Technology Devices International Ltd (FTDI) Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow, G41 1HH, United Kingdom Tel.: +44 (0) 141 429 2777 Fax: + 44 (0) 141 429 2758 E-Mail (Support): [email protected] Web: http://www.ftdichip.com Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides pre liminary information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow, G41 1HH, United Kingdom. Scotland Registered Number: SC136640 Copyright © 2010 Future Technology Devices International Limited ` 1 Document Reference No.: FT_000331 USB Hi-Speed Serial/Hub Module Version 1.2 Clearance No.: FTDI# 174 Introduction The FT4232H based USB Hi-Speed Serial/Hub Module is a USB interface expansion module targeted at connecting to the FTDI V2DIPx modules to expand the number of interfaces. However, it is not limited to this application. It can also be used as a hub device or an FT4232H evaluation module. The module has a USB 2.0 Hi-Speed hub chip which supports up to three external downstream USB ports: 2 via a dual USB connector and 1 via the DIL connector pins. Aditionally, by utilizing the FT4232H USB Hi-Speed four-port bridge chip which handles all the USB signalling and protocols, the module can easily support up to 4 flexible interfacing ports. It is ideal for development purposes to quickly prove functionality of adding USB to a target design. Figure 1.1 - FT4232H Serial/Hub Module The module utilises the GL850G USB 2.0 hub controller which provides a low-cost, and widely used USB 2.0 hub solution, to provide up to 4 downstream USB ports. The GL850G is a single USB hub solution. The GL850G is a full function solution which support both Individual/Gang power management modes and two-color (green/amber) status LED. GL850G can be used with an external EEPROM (on the module) which can be used to customize PID/VID and other more complicated settings. The FT4232H used on the Module is FTDI’s 5th generation of USB devices. The FT4232H is a USB 2.0 HiSpeed (480Mb/s) to UART/MPSSE IC. The device features four interfaces that can be configured for asynchronous or synchronous serial communications. Two of these interfaces have an option to be independently configured via an MPSSE engine. This allows the FT4232H to operate as two UART/BitBang ports plus two MPSSE engines which can be used to emulate JTAG, SPI, I2C, Bit-bang or other synchronous serial modes. The FT4232H datasheet, DS_FT4232H, is available at http://ftdichip.com/Support/Documents/DataSheets/ICs/DS_FT4232H.pdf The block diagram of FT4232H Hub Module is shown in Figure 1.2. Copyright © 2010 Future Technology Devices International Limited 1 Document Reference No.: FT_000331 USB Hi-Speed Serial/Hub Module Version 1.2 Clearance No.: FTDI# 174 ` Figure 1.2 – Block diagram of USB Hi-Speed Serial/Hub Module As the block diagram Figure 1.2 shows, the USB Hi-Speed Serial/Hub Module routes the signals from the GL850G and FT4232H devices to two 18-pin, 0.1”, single-row headers and a dual-port USB A-type socket. This allows easy connection to most PCB header sockets and ribbon cables. To reduce the connector pin count, only channel A and B fan out all the 8 data signals to the 18-pin header. For the channel C and channel D, since many designs only use the TXD/RXD/CTS/RTS signals in UART communication, only these 4 data signals are fanned out. This meets most application requirements. To use the FT4232H connected to a PC , the FT4232H Hub Module requires specific USB device drivers, available free from http://www.ftdichip.com. The drivers are used to make the FT4232H on the Module appear as a four virtual COM ports (VCP). This then allows the user to communicate with the USB interface via a standard PC serial emulation port (TTY). Another FTDI USB driver, the D2XX driver, can also be used with application software to directly access the FT4232H on the Mini Module though a DLL. The main target application for the USB hi-Speed Serial/Hub Module is that it can be attached to the FTDI VNC2 based V2DIPx modules (there are 6 different sizes) as a expansion module. By connecting the USB Hi-Speed Serial/Hub Module to the USB socket on the V2DIPx modules, the two modules can work as a single module to be placed on the bread board. The USB Hi-Speed Serial/Hub Module expands the interfaces of V2DIPx module with up to 3 USB ports and 4 serial ports. More information is available on the V2DIPx modules at http://www.ftdichip.com/Products/Modules/DevelopmentModules.htm. 1.1 Part Numbers Part Number Description FT-MOD-4232HUB USB Hi-Speed_Serial/Hub_Module Copyright © 2010 Future Technology Devices International Limited 2 ` Document Reference No.: FT_000331 USB Hi-Speed Serial/Hub Module Version 1.2 Clearance No.: FTDI# 174 Table of Contents 1 Introduction............................................................................................ 1 1.1 2 Part Numbers ....................................................................................................... 2 Typical Applications .............................................................................. 4 2.1 Features ............................................................................................................... 4 2.2 Driver Support ..................................................................................................... 4 3 Electrical Details .................................................................................... 5 4 Mechanical details ................................................................................. 9 5 Schematic Diagram ............................................................................. 10 6 Contact Information............................................................................. 12 Appendix A – FT4232H EEPROM Configuration........................................................ 10 Appendix B – List of Figures and Tables ................................................................... 11 List of Figures............................................................................................................... 11 List of Tables ................................................................................................................ 11 Appendix C – Revision History ................................................................................... 12 Copyright © 2010 Future Technology Devices International Limited 3 Document Reference No.: FT_000331 USB Hi-Speed Serial/Hub Module Version 1.2 Clearance No.: FTDI# 174 ` 2 Typical Applications Expansion module for the FTDI V2DIPx modules to expand usb ports and interfaces. Rapid USB integration into existing electronic systems. Prototyping platform for USB interface on new systems. USB 2.0 hub device to support up to 3 downstream USB ports. USB to muli-port JTAG, SPI and I2C interfaces (Two Multi-Protocol Synchronous Serial Engines – MPSSE – available with the FT4232H) USB to multi-port asynchronous serial interfaces (up to 4 ports available). 2.1 Features The USB Hi-Speed Serial/Hub Module has the following features: General: USB 2.0 Hi-Speed compatible Defaults to 4 RS232 interfaces. One standard Type A USB header to connect to the Host Asynchronous Serial data transfer rates from 300 baud to 12 Mbaud at TTL levels USB Hi-Speed FT4232H device for USBSerial/Bitbang communications. Entire USB protocol handled by USB module Synchronous Serial (MPSSE) data rates of up to 30Mbps on JTAG, SPI and I2C USB 2.0 Hi-Speed hub controller integrated to support up to 3 downstream USB ports One dual-port USB A socket and 0.1” pitch header to support up to 3 downstream USB ports USB hub controller and FT4232H are USB bus powered – no external power supply needed Green/Amber status LED for downstream USB port 2&3. External power input pin available to supply external downstream USB ports. LED indicating power supply to external downstream USB ports Support for USB suspend and resume Onboard EEPROM 93LC56 for FT4232H configuration 4 Asynchronous serial interfaces available which include 2 independent MPSSE engines. UHCI / OHCI / EHCI host controller compatible 2.2 Driver Support Royalty free VIRTUAL COM PORT Royalty free D2XX Direct Drivers (VCP) DRIVERS for... (USB Drivers + DLL S/W Interface) Windows 2000, Server 2003, XP Server 2008 Windows 2000, Server 2003, Server 2008 Windows XP and XP 64-bit Windows XP and XP 64-bit Windows Vista and Vista 64-bit Windows Vista and Vista 64-bit Windows 7 and 7 64-bit Windows 7 and 7 64-bit Windows XP Embedded Windows XP Embedded Windows CE 4.2, 5.0, 5.2 and 6.0 Windows CE 4.2, 5.0, 5.2 and 6.0 Mac OS-X Linux (2.4 or later) and Linux x86_64 Linux (2.6.9 or later) The drivers listed above are all available to download for free from www.ftdichip.com. Copyright © 2010 Future Technology Devices International Limited 4 ` 3 Document Reference No.: FT_000331 USB Hi-Speed Serial/Hub Module Version 1.2 Clearance No.: FTDI# 174 Electrical Details The electrical details and connections of the USB Hi-Speed Serial/Hub Module are shown in Figure 3.1 and table 3.1 – table 3.3. Figure 3.1 USB Hi-Speed Serial/Hub Module Electrical Connections (Top View) USB Hi-Speed Serial/Hub Module has 4 connectors on the board. The detailed descriptions of these connectors are listed in Table 3.1. Reference Designator CN1 CN2 Description USB A signal header to connect to the host port Dual-port USB A socket connects to 2 downstream USB devices CN3 0.1” 18-pin header CN4 0.1” 18-pin header Table 3.1 USB Hi-Speed Serial/Hub Module Connectors Copyright © 2010 Future Technology Devices International Limited 5 Document Reference No.: FT_000331 USB Hi-Speed Serial/Hub Module Version 1.2 Clearance No.: FTDI# 174 ` The pin descriptions of CN3 and CN4 are given in Table 3.2 and Table 3.3. Connector Pin Name Description CN3-1 NC CN3-2 VCC_BUS CN3-3 5V CN3-4 DD0 FT4232H DD0 pin CN3-5 DD1 FT4232H DD1 pin CN3-6 DD2 FT4232H DD2 pin CN3-7 DD3 FT4232H DD3 pin CN3-8 GND 0V Power pin CN3-9 AD0 FT4232H AD0 pin CN3-10 AD1 FT4232H AD1 pin CN3-11 AD2 FT4232H AD2 pin CN3-12 AD3 FT4232H AD3 pin CN3-13 AD4 FT4232H AD4 pin CN3-14 AD5 FT4232H AD5 pin CN3-15 AD6 FT4232H AD6 pin CN3-16 AD7 FT4232H AD7 pin CN3-17 DP4 USB hub downstream port 4 D+ signal pin CN3-18 DM4 USB hub downstream port 4 D- signal pin Not connected pin USB +5V VBUS power pin (output) from upstream USB port +5v power pin (input) to supply downstream USB ports Table 3.2 USB Hi-Speed Serial/Hub Module Connection – CN3 Copyright © 2010 Future Technology Devices International Limited 6 Document Reference No.: FT_000331 USB Hi-Speed Serial/Hub Module Version 1.2 Clearance No.: FTDI# 174 ` Connector Pin Name Description CN4-1 NC CN4-2 PWREN# FT4232H PWREN# pin CN4-3 DATA FT4232H EEDATA pin CN4-4 CS FT4232H EECS pin CN4-5 CLK FT4232H EECLK pin CN4-6 GND 0V Power pin CN4-7 CD3 FT4232H CD3 pin CN4-8 CD2 FT4232H CD3 pin CN4-9 CD1 FT4232H CD1 pin CN4-10 CD0 FT4232H CD0 pin CN4-11 BD7 FT4232H BD7 pin CN4-12 BD6 FT4232H BD6 pin CN4-13 BD5 FT4232H BD5 pin CN4-14 BD4 FT4232H BD4 pin CN4-15 BD3 FT4232H BD3 pin CN4-16 BD2 FT4232H BD2 pin CN4-17 BD1 FT4232H BD1 pin CN4-18 BD0 FT4232H BD0 pin Not connected pin Table 3.3 USB Hi-Speed Serial/Hub Module Connection – CN4 In most cases, the FT4232H pin is connected directly to the associated pin on CN3 or CN4. There are also several LEDs available on the FT4232H Hub Module to indicate the status of power and USB hub port. Detailed functions of LEDs are described in Table 3.4. LED Reference Designator Color Function Description D1 Yellow Power to supply external downstream USB ports D2 Amber Overcurrent status of downstream USB port 2 D3 Green Transfer status of downstream USB port 2 D4 Green Transfer status of downstream USB port 3 D5 Amber Overcurrent status of downstream USB port 3 Figure 3.4 Functions of status LEDs on the module Copyright © 2010 Future Technology Devices International Limited 7 ` Document Reference No.: FT_000331 USB Hi-Speed Serial/Hub Module Version 1.2 Clearance No.: FTDI# 174 Power Supply of FT4232H Hub Module The GL850G and the FT4232H ICs and their related circuits on the USB Hi-Speed Serial/Hub Module are directly powered by USB bus power. The estimated current consumed by the cirucuits of module is about 100-300mA depending on the application. It is important that the user ensures that the host can supply this current via USB. The maximum total current consumed by the external usb devices on downstream port 2 and 3 is 1A. If the total current exceed 1A, the fuse on the USB Hi-Speed Serial/Hub Module will be disconnected. If this occurs then LEDs D2 and D5 on the module will illuminate to indicate over-current status. There are two options to supply power to external downstream usb devices connected to ports 2 and 3. 1. Use USB bus power to supply downstream ports: Connect 5V to VCC_BUS (CN3, pin 3 to CN3, pin 2). This connection uses the power from upstream USB bus to supply the downstream USB ports of the USB hub. With this connection, user should make sure that the usb host can supply enough current to the external USB devices – in addition to the current required by the module. 2. Use external power to supply downstream ports: Connect 5V (CN3, pin 3) to external +5v DC power supply. This connection takes the power from external power to supply the downstream USB ports of USB hub. Users should also make sure that the external power can supply enough current required by the external devices. Note: It is recommened to select the mode of operation before connecting the USB Hi-Speed Serial/Hub Module. Copyright © 2010 Future Technology Devices International Limited 8 Document Reference No.: FT_000331 USB Hi-Speed Serial/Hub Module Version 1.2 Clearance No.: FTDI# 174 ` 4 Mechanical details The mechanical details of the USB Hi-Speed Serial/Hub Module are shown in Figure 4.1: 4. 27 75. 04 FT4232H Hub Modul e FT4232H 13. 27 GL850G 12. 06 23. 37 CN2 2. 54 17. 09 18. 7 16. 21 15. 8 4. 82 1. 58 28. 9 9. 0 Figure 4.1 USB Hi-Speed Serial/Hub Module Dimensions All dimensions are in millimetres. The headers CN3 and CN4 are mounted to the bottom of the PCB. The overall height below the PCB is 11.5mm, with a body which exposes 9.0mm of the pins. The pins are 0.025 inch square. Copyright © 2010 Future Technology Devices International Limited 9 ` 5 Document Reference No.: FT_000331 USB Hi-Speed Serial/Hub Module Version 1.2 Clearance No.: FTDI# 174 Schematic Diagram Figure 5.1 USB Hi-Speed Serial/Hub Module Schematic – Page 1 Copyright © 2010 Future Technology Devices International Limited 10 ` Document Reference No.: FT_000331 USB Hi-Speed Serial/Hub Module Version 1.2 Clearance No.: FTDI# 174 Figure 5.2 USB Hi-Speed Serial/Hub Module Schematic – Page 2 Copyright © 2010 Future Technology Devices International Limited 11 Document Reference No.: FT_000331 USB Hi-Speed Serial/Hub Module Version 1.2 Clearance No.: FTDI# 174 ` 6 Contact Information Head Office – Glasgow, UK Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow, G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) Web Site URL Web Shop URL [email protected] [email protected] [email protected] http://www.ftdichip.com http://www.ftdichip.com Branch Office – Taipei, Taiwan Future Technology Devices International Limited (Taiwan) 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8797 1330 Fax: +886 (0) 2 8751 9737 E-mail (Sales) [email protected] E-mail (Support) [email protected] E-mail (General Enquiries) [email protected] Web Site URL http://www.ftdichip.com Branch Office – Hillsboro, Oregon, USA Future Technology Devices International Limited (USA) 7235 NW Evergreen Parkway, Suite 600 Hillsboro, OR 97123-5803 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-Mail (Sales) E-mail (Support) E-mail (General Enquiries) Web Site URL [email protected] [email protected] [email protected] http://www.ftdichip.com Branch Office – ShangHai, China Future Technology Devices International Limited (China) Room 408, 317 Xianxia Road, ChangNing District, ShangHai, P.R. China Tel: +86 (21) 62351596 Fax: +86 (21) 62351595 E-Mail (Sales) E-mail (Support) E-Mail (General Enquiries) Web Site URL [email protected] [email protected] [email protected] http://www.ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. Copyright © 2010 Future Technology Devices International Limited 12 Document Reference No.: FT_000331 FT4232H Datasheet Version 1.2 Clearance No.: FTDI# 174 Appendix A – FT4232H EEPROM Configuration The USB Hi-Speed Serial/Hub Module utilizes an EEPROM which contains the USB configuration descriptors for the FT4232H. When the Mini Module is plugged into a PC or a USB reset is performed, the PC will read these descriptors. The default values stored into the EEPROM are defined in Table 6.1. Parameter Value Notes USB Vendor ID (VID) 0403h FTDI default VID (hex) USB Product UD (PID) 6011h FTDI default PID (hex) Serial Number Enabled? Yes Serial Number See Note Pull down I/O Pins in USB Suspend A unique serial number is generated and programmed into the EEPROM during device final test. Enabling this option will make the device pull down on the Disabled UART interface lines when the power is shut off (PWREN# is high). Manufacturer Name FTDI Product Description FT4232H Hub Module Max Bus Power Current 500mA Power Source Bus Powered Device Type FT4232 Returns USB 2.0 device description to the host. USB Version 0200 Note: The device is be a USB 2.0 Full Speed device (12Mb/s) as opposed to a USB 2.0 Hi-Speed device (480Mb/s). Remote Wake Up Enabled High Current I/Os Enabled Load VCP Driver Disabled Taking RI# low will wake up the USB host controller from suspend. Enables the high drive level on the UART and CBUS I/O pins. Makes the device load the VCP driver interface for the device. Table 6.1 Default Internal EEPROM Configuration The EEPROM for FT4232H chip on the USB Hi-Speed Serial/Hub Module can be re-programmed over USB using the utility program FT_Prog. FT_Prog can be downloaded from http://www.ftdichip.com/Support/Utilities.htm. Users who do not have their own USB Vendor ID but who would like to use a unique Product ID in their design can apply to FTDI for a free block of unique PIDs. Contact FTDI support for this service. Copyright © 2010 Future Technology Devices International Limited 10 Document Reference No.: FT_000331 FT4232H Datasheet Version 1.2 Clearance No.: FTDI# 174 Appendix B – List of Figures and Tables List of Figures Figure 1.1 - FT4232H Serial/Hub Module ................................................................................... 1 Figure 3.1 USB Hi-Speed Serial/Hub Module Electrical Connections (Top View) ..................................... 5 Figure 4.1 USB Hi-Speed Serial/Hub Module Dimensions ................................................................... 9 Figure 5.1 USB Hi-Speed Serial/Hub Module Schematic – Page 1 ...................................................... 10 Figure 5.2 USB Hi-Speed Serial/Hub Module Schematic – Page 2 ...................................................... 11 List of Tables Table 3.1 USB Hi-Speed Serial/Hub Module Connectors ..................................................................... 5 Table 6.1 Default Internal EEPROM Configuration............................................................................ 10 Copyright © 2010 Future Technology Devices International Limited 11 Document Reference No.: FT_000331 FT4232H Datasheet Version 1.2 Clearance No.: FTDI# 174 Appendix C – Revision History Version 1.0 First Release 13th October 2010 Version 1.1 Added part number 21st October 2010 Version 1.2 Changed title from FT4232H Hub Module to USB Hi-Speed Serial/Hub Module Version 1.2 Corrected Fig. 1.2 28th October 2010 Released Rev 1.2 28st October 2010 Copyright © 2010 Future Technology Devices International Limited 12