Future Technology Devices International Ltd USB TO RS422 UART SERIAL CONVERTER PCB Datasheet Document Reference No.: FT_000119 Version 1.02 Issue Date: 13-04-09 Future Technology Devices International Limited (FTDI) Unit1, 2 Seaward Place, Centurion Business Park,, Glasgow G41 1HH United Kingdom Tel.: +44 (0) 141 429 2777 Fax: + 44 (0) 141 429 2758 E-Mail (Support): [email protected] Web: http://www.ftdichip.com Copyright © 2008 Future Technology Devices International Limited Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit1, 2 Seaward Place, Centurion Business Park, Glasgow, G41 1HH, United Kingdom. Scotland Registered Number: SC136640 Copyright © 2009 Future Technology Devices International Limited Document Reference No.: FT_000119 USB TO RS422 UART SERIAL CONVERTER PCB Datasheet Version 1.02 Clearance No.: FTDI#79 1 Description The USB-RS422-PCB is a USB to RS422 level serial UART converter PCB incorporating FTDI’s FT232RQ USB to Serial UART interface IC device which handles all the USB signalling and protocols. The PCB provides a fast, simple way to connect devices with a RS422 interface to USB. Each USB-RS422-PCB contains a small internal electronic circuit board, utilising the FT232R plus a USB type-A connector. The FT232R datasheet, DS_FT232R, is available at http://www.ftdichip.com. The integrated electronics also include an RS422 transceiver plus Tx and Rx LEDs which give a visual indication of UART traffic. The PCB is USB powered and USB 2.0 full speed compatible. Each PCB supports a data transfer rate up to 3 Mbaud and supports the FTDIChip-ID™, with a unique USB serial number programmed into the FT232R. This feature can be used to create a security or password protected file transfer access using the PCB. Further information and examples on this feature are available at http://www.ftdichip.com under FTDIChip-ID Projects. The USB-RS422-PCB requires USB drivers, available free from http://www.ftdichip.com, which are used to make the FT232R on the PCB appear as a virtual COM port (VCP). This then allows the user to communicate with the USB interface via a standard PC serial emulation port (for example TTY). Another FTDI USB driver, the D2XX driver, can also be used with application software to directly access the FT232R on the PCB though a DLL. This is illustrated in the Figure 1.1. Figure 1.1 Using the USB-RS422-PCB 1.1 Part Number The following Table 1.1 gives details of the available USB-RS422-PCB. Part Number Description USB-RS422-PCB USB to RS422 level UART PCB Table 1.1 USB-RS422-PCB Part Number Copyright © 2009 Future Technology Devices International Limited 1 Document Reference No.: FT_000119 USB TO RS422 UART SERIAL CONVERTER PCB Datasheet Version 1.02 Clearance No.: FTDI#79 Table of Contents 1 Description ..................................................................................... 1 1.1 2 Part Number.................................................................................................. 1 Typical Applications ........................................................................ 3 2.1 Driver Support .............................................................................................. 3 2.2 Features ........................................................................................................ 4 3 Features of FT232R applicable to USB-RS422-PCB ......................... 5 4 USB-RS422-PCB Connector Pin Out and Mechanical details ............ 6 4.1 USB-RS422-PCB Signal Descriptions ............................................................. 8 4.2 USB-RS422-PCB Electrical Parameters .......................................................... 8 5 USB-RS422-PCB Circuit Schematic ............................................... 10 6 Contact Information ..................................................................... 11 Appendix A - PCB EEPROM Configuration ........................................... 13 Appendix B - List of Figures and Tables.............................................. 14 Appendix C - Revision History ............................................................ 15 Copyright © 2009 Future Technology Devices International Limited 2 Document Reference No.: FT_000119 USB TO RS422 UART SERIAL CONVERTER PCB Datasheet Version 1.02 Clearance No.: FTDI#79 2 Typical Applications • USB to Serial RS422 Level Converter. • USB Instrumentation PC interface. • Upgrading Legacy Peripherals to USB. • USB Industrial Control. • Interface Microcontroller UART or I/O to USB. • USB password protected file transfers. • Interface FPGA / PLD to USB. 2.1 Driver Support Royalty free VIRTUAL COM PORT Royalty free D2XX Direct Drivers (VCP) DRIVERS for... (USB Drivers + DLL S/W Interface) • Windows 98, 98SE, ME, 2000, Server 2003 and Server 2008 • Windows 98, 98SE, ME, 2000, Server 2003 and Server 2008 • Windows XP and XP 64-bit • Windows XP and XP 64-bit • Windows Vista and Vista 64-bit • Windows Vista and Vista 64-bit • Windows XP Embedded • Windows XP Embedded • Windows CE 4.2, 5.0 and 6.0 • Windows CE 4.2, 5.0 and 6.0 • Mac OS 8/9, OS-X • Linux 2.4 and greater • Linux 2.4 and greater • Mac OS-X The drivers listed above are all available to download for free from www.ftdichip.com. Various 3rd Party Drivers are also available for various other operating systems - see www.ftdichip.com for details. Copyright © 2009 Future Technology Devices International Limited 3 Document Reference No.: FT_000119 USB TO RS422 UART SERIAL CONVERTER PCB Datasheet Version 1.02 Clearance No.: FTDI#79 2.2 Features • USB-RS422-PCB provides a USB to RS422 Serial UART interface. • Support for FT232R FTDIChip-ID™ feature for improved security. • Entire USB protocol handled by the electronics on the PCB. • PCB is USB Powered - no external supply required. • EIA/TIA-422 interface with low power requirements. • Low USB bandwidth consumption. • UHCI / OHCI / EHCI host controller compatible. • UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no parity. • USB 2.0 Full Speed compatible. • -40°C to +85°C operating temperature range. • RoHS compliant • ESD Protection for RS-422 I/O's ±15kV Human Body Model (HBM) ±15kV EN61000-4-2 Air Gap Discharge ±8kV EN61000-4-2 Contact Discharge • Data transfer rates from 300 baud up to 3 Mbaud. • Internal EEPROM with user writeable area. • FTDI’s royalty-free VCP allow for communication as a standard emulated COM port and D2XX ‘direct’ drivers provide DLL application programming interface. Copyright © 2009 Future Technology Devices International Limited 4 Document Reference No.: FT_000119 USB TO RS422 UART SERIAL CONVERTER PCB Datasheet Version 1.02 Clearance No.: FTDI#79 3 Features of FT232R applicable to USB-RS422-PCB The USB-RS422-PCB uses FTDI’s FT232RQ USB to serial IC device. This section summarises the key features of the FT232RQ which apply to the USB-RS422-PCB. For further details, and a full features and enhancements description consult the FT232R datasheet, this is available from www.ftdichip.com. Internal EEPROM. The internal EEPROM is used to store USB Vendor ID (VID), Product ID (PID), device serial number, product description string and various other USB configuration descriptors. Each FT232RQ is supplied with the internal EEPROM pre-programmed as described in Appendix A - PCB EEPROM Configuration. The internal EEPROM descriptors can be programmed in circuit, over USB without any additional voltage requirement. It can be programmed using the FTDI utility software called MPROG, which can be downloaded from FTDI Utilities on the FTDI website (www.ftdichip.com). Additionally, there is a user area of the internal EEPROM available to system designers to allow storing of data (note that this is not modified by MPROG). Lower Operating and Suspend Current. The FT232R has a low 15mA operating supply current and a very low USB suspend current of approximately 70µA. Low USB Bandwidth Consumption. The USB interface of the FT232R, and therefore the USB-RS422PCB has been designed to use as little as possible of the total USB bandwidth available from the USB host controller. FTDIChip-ID™. The FT232R includes the new FTDIChip-ID™ security dongle feature. This FTDIChip-ID™ feature allows a unique number to be burnt into each FT_232RQ during manufacture. This number cannot be reprogrammed. This number is only readable over USB can be used to form the basis of a security dongle which can be used to protect any customer application software being copied. This allows the possibility of using the USB-RS422-PCB as a dongle for software licensing. Further to this, a renewable license scheme can be implemented based on the FTDIChip-ID™ number when encrypted with other information. This encrypted number can be stored in the user area of the FT232R internal EEPROM, and can be decrypted, then compared with the protected FTDIChip-ID™ to verify that a license is valid. Web based applications can be used to maintain product licensing this way. An application note, AN232R-02, available from FTDI website (www.ftdichip.com) describes this feature. Extended Operating Temperature Range - The USB-RS422-PCB is capable of operating over an extended temperature range of -40º to +85ºC thus allowing it to be used in automotive or industrial applications. Copyright © 2009 Future Technology Devices International Limited 5 Document Reference No.: FT_000119 USB TO RS422 UART SERIAL CONVERTER PCB Datasheet Version 1.02 Clearance No.: FTDI#79 4 USB-RS422-PCB Connector Pin Out and Mechanical details RED LED TOP GRN LED RS 422 Tranceiver TXDTXD+ GND RS 422 Tranceiver RTSRTS+ GND CTS- BOTTOM FT232R CTS+ RXDRXD+ USB-RS422-PCB REV 2 Figure 4.1 USB-RS422-PCB Pin Out (Top is TOP View, Bottom is BOTTOM View) The mechanical details of the PCB are shown in the following diagram Figure 4.2 The pads were re-arranged on the PCB to allow for easier wiring which resulted in a Rev 2 PCB. There were no other changes between Rev 1 and Rev 2. Copyright © 2009 Future Technology Devices International Limited 6 Document Reference No.: FT_000119 USB TO RS422 UART SERIAL CONVERTER PCB Datasheet Version 1.02 Clearance No.: FTDI#79 Figure 4.2 USB-RS422-PCB, Mechanical Details Copyright © 2009 Future Technology Devices International Limited 7 Document Reference No.: FT_000119 USB TO RS422 UART SERIAL CONVERTER PCB Datasheet Version 1.02 Clearance No.: FTDI#79 4.1 USB-RS422-PCB Signal Descriptions Name Type Description GND GND Device ground supply pin. CTS+ Input Clear to Send Control + (B), Input TXD- Output Data – (A) Output TXD+ Output Data + (B) Output RXD+ Input RTS+ Output Request To Send Control + (B), Output RTS- Output Request To Send Control – (A), Output RXD- Input Data – (A) Input CTS- Input Clear to Send Control input – (A), Input Data + (B) Input Table 4.1 USB-RS422-PCB Signal Descriptions 4.2 USB-RS422-PCB Electrical Parameters Parameter Description Minimum Typical Maximum Units +12 V Conditions Receiver Input VCM Common-mode input voltage range -7 1.0 IN Input Current VIN = +12V mA –0.8 VTH VIHYST RIN DIfferential Threshold Voltage,VTH -0.2 Input Hysteresis Input Resistance, RIN 12 +0.2 VIN = –7V V 20 mV 15 kΩ Transmitter Output VOD DIfferential Output Voltage, dVOD 1.5 5 V With RL = 54Ω. CL = 50pF * Table 4.2 USB-RS422-PCB I/O Characteristics * - The 54 ohms is the equivalent of two 120 ohm termination resistors placed on each side of the transmission line and the input impedance of 32 receivers on the line. Copyright © 2009 Future Technology Devices International Limited 8 Document Reference No.: FT_000119 USB TO RS422 UART SERIAL CONVERTER PCB Datasheet Version 1.02 Clearance No.: FTDI#79 Description Conditions Minimum Typical ESD HBM RS-422 Inputs and Outputs ±15 kV EN61000-4-2ContactDischarge RS-422 Inputs and Outputs ±8 kV EN61000-4-2AirGapDischarge RS-422 Inputs and Outputs ±15 kV Maximum Table 4.3 USB-RS422-PCB ESD Tolerance Copyright © 2009 Future Technology Devices International Limited 9 Document Reference No.: FT_000119 USB TO RS422 UART SERIAL CONVERTER PCB Datasheet Version 1.02 Clearance No.: FTDI#79 5 USB-RS422-PCB Circuit Schematic The circuit schematic of the USB-RS422-PCB, utilising the FTDI FT232R, is shown in Figure 5.1 Figure 5.1 Circuit Schematic of USB-RS422-PCB. Copyright © 2009 Future Technology Devices International Limited 10 Document Reference No.: FT_000119 USB TO RS422 UART SERIAL CONVERTER PCB Datasheet Version 1.02 Clearance No.: FTDI#79 6 Contact Information Head Office – Glasgow, UK Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 E-mail (Sales) [email protected] E-mail (Support) [email protected] E-mail (General Enquiries) [email protected] Web Site URL http://www.ftdichip.com Web Shop URL http://www.ftdichip.com Branch Office – Shanghai, China Future Technology Devices International Limited (China) Room 408, 317 Xianxia Road, ChangNing District, ShangHai, China Tel: +86 (21) 62351596 Fax: +86(21) 62351595 E-Mail (Sales): [email protected] E-Mail (Support): [email protected] E-Mail (General Enquiries): [email protected] Web Site URL: http://www.ftdichip.com Branch Office – Taipei, Taiwan Future Technology Devices International Limited (Taiwan) 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8797 1330 Fax: +886 (0) 2 8751 9737 E-mail (Sales) [email protected] E-mail (Support) [email protected] E-mail (General Enquiries) [email protected] Web Site URL http://www.ftdichip.com Branch Office – Hillsboro, Oregon, USA Future Technology Devices International Limited (USA) 7235 NW Evergreen Parkway, Suite 600 Hillsboro, OR 97123-5803 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-Mail (Sales) [email protected] E-Mail (Support) [email protected] Web Site URL http://www.ftdichip.com Copyright © 2009 Future Technology Devices International Limited 11 Document Reference No.: FT_000119 USB TO RS422 UART SERIAL CONVERTER PCB Datasheet Version 1.02 Clearance No.: FTDI#79 Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. Copyright © 2009 Future Technology Devices International Limited 12 Document Reference No.: FT_000119 USB TO RS422 UART SERIAL CONVERTER PCB Datasheet Version 1.02 Clearance No.: FTDI#79 Appendix A - PCB EEPROM Configuration Each USB-RS422-PCB is controlled by the FTDI FT232R IC. This FT232R device contains an EEPROM which contains the USB configuration descriptors for that device. When the PCB is plugged into a PC or a USB reset is performed, the PC will read these descriptors. The default values stored into the internal EEPROM are defined in Table 0.1 Default Internal EEPROM Configuration Parameter Value USB Vendor ID (VID) 0403h FTDI default VID (hex) USB Product UD (PID) 6001h FTDI default PID (hex) Serial Number Enabled? Serial Number Pull down I/O Pins in USB Suspend Yes See Note A unique serial number is generated and programmed into the EEPROM during device final test. Disabled Enabling this option will make the device pull down on the UART interface lines when the power is shut off (PWREN# is high). Manufacturer Name FTDI Product Description See note Max Bus Power Current Power Source Device Type USB Version Notes USB-RS422-PCB 90mA Bus Powered FT232R 0200 Returns USB 2.0 device description to the host. Note: The device is be a USB 2.0 Full Speed device (12Mb/s) as opposed to a USB 2.0 High Speed device (480Mb/s). Remote Wake Up Disabled High Current I/Os Enabled Load VCP Driver Enabled Invert TXD Disabled Signal on this pin becomes TXD# if enable. Invert RXD Disabled Signal on this pin becomes RXD# if enable. Invert RTS# Disabled Signal on this pin becomes RTS if enable. Invert CTS# Disabled Signal on this pin becomes CTS if enable. Enables the high drive level on the UART and CBUS I/O pins. Makes the device load the VCP driver interface for the device. Table 0.1 Default Internal EEPROM Configuration The internal EEPROM on the PCB can be re-programmed over USB using the utility program MPROG. MPROG can be downloaded from the www.ftdichip.com. Version 2.8a or later is required for the FT232R chip. Users who do not have their own USB Vendor ID but who would like to use a unique Product ID in their design can apply to FTDI for a free block of unique PIDs. Contact FTDI support for this service. Copyright © 2009 Future Technology Devices International Limited 13 Document Reference No.: FT_000119 USB TO RS422 UART SERIAL CONVERTER PCB Datasheet Version 1.02 Clearance No.: FTDI#79 Appendix B - List of Figures and Tables List of Figures Figure 1.1 Using the USB-RS422-PCB........................................................................................................... 1 Figure 4.1 USB-RS422-PCB Pin Out (Top is TOP View, Bottom is BOTTOM View).................................. 6 Figure 4.2 USB-RS422-PCB, Mechanical Details .......................................................................................... 7 Figure 5.1 Circuit Schematic of USB-RS422-PCB. ..................................................................................... 10 List of Tables Table 1.1 USB-RS422-PCB Part Number ....................................................................................................... 1 Table 4.1 USB-RS422-PCB Signal Descriptions ........................................................................................... 8 Table 4.2 USB-RS422-PCB I/O Characteristics ............................................................................................. 8 Table 4.3 USB-RS422-PCB ESD Tolerance ................................................................................................... 9 Table 0.1 Default Internal EEPROM Configuration..................................................................................... 13 Copyright © 2009 Future Technology Devices International Limited 14 Document Reference No.: FT_000119 USB TO RS422 UART SERIAL CONVERTER PCB Datasheet Version 1.02 Clearance No.: FTDI#79 Appendix C - Revision History Version Draft First Draft January 2009 Version 1.0 First Release 21st January 2009 Version 1.01 Corrected the PCB drawing and TW address 09th February 2009 Version 1.02 Added rev1 and rev2 PCB drawings 13th April 2009 Copyright © 2009 Future Technology Devices International Limited 15