VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 FTDI Chip VM800P Datasheet Embedded Video Engine Plus Module General Purpose Multi Media Controller The VM800P is a development module for FTDI’s FT800, which is used to develop and demonstrate the functionality of the FT800 Embedded Video Engine, EVE. The VM800P is a stand-alone display system which has a flash based microcontroller on board, thus providing a fully integrated display system ready to go. The VM800P supports many I/O daughter cards or shields for expanding external interfacing and control. These shields use 1 or 2 Micro-MaTch miniature connectors to interface to the VM800P main module. Users will be able to purchase shields from FTDI Chip in the coming months, or alternatively can build their own shield for specific applications. The VM800P series of modules support 3 different LCD panel size options and are designed for industrial or commercial environments with precision fitted bezels in either black (-BK) or pearl (-PL). VM800P35A-xx is the 3.5” LCD VM800P43A-xx is the 4.3” LCD VM800P50A-xx is the 5.0” LCD The VM800P utilises the FTDI FT800 Embedded Video Engine, EVE. Graphic, audio and touch features of the FT800 chip can be accessed with the VM800P. For a full list of the FT800’s features please see the FT800 datasheet. The VM800P module has the following features: FT800 for graphics, audio and touch processing ATMEGA328P system microcontroller operating at 5V/16MHz supporting Arduino libraries Touch screen LCD panel Backlight LED driver Audio power amplifier and micro speaker FT232R USB serial port for firmware upgrade Micro-SD socket for application storage, including 4GByte SD Card pre-loaded with sample applications Battery backed Real Time Clock 2x Micro-MaTch miniature connectors for daughter card expansion 5V power supply from micro-USB or battery connector Precision fitted bezel in black(-BK) or pearl (-PL) Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH United Kingdom. Scotland Registered Company Number: SC136640 VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 1 Ordering Information Part No. Description VM800P35A-BK FT800 Display System, ATMEG328P @ 5V/16MHz, Micro-SD socket, 3.5” 320x240 resolution TFT LCD with resistive touch panel, black case VM800P43A-BK FT800 Display System, ATMEG328P @ 5V/16MHz, Micro-SD socket, 4.3” 480x272 resolution TFT LCD with resistive touch panel, black case VM800P50A-BK FT800 Display System, ATMEG328P @ 5V/16MHz, Micro-SD socket, 5.0” 480x272 resolution TFT LCD with resistive touch panel, black case VM800P35A-PL FT800 Display System, ATMEG328P @ 5V/16MHz, Micro-SD socket, 3.5” 320x240 resolution TFT LCD with resistive touch panel, pearl case VM800P43A-PL FT800 Display System, ATMEG328P @ 5V/16MHz, Micro-SD socket, 4.3” 480x272 resolution TFT LCD with resistive touch panel, pearl case VM800P50A-PL FT800 Display System, ATMEG328P @ 5V/16MHz, Micro-SD socket, 5.0” 480x272 resolution TFT LCD with resistive touch panel, pearl case ACCESSORIES VA800A-PROG Accessory - PLUS Production Programmer for ATMEGA328P inc Tag Connect TC2030-IDC-FP cable VA-PSU-UK1 Accessory - UK Model 5V/1A USB Power Supply ( Mfr # JX-B0520C-1-B ) VA-PSU-US1 Accessory - US Model 5V/1A USB Power Supply ( Mfr # JX-B0520B-1-B ) VA-PSU-EU1 Accessory - EU Model 5V/1A USB Power Supply ( Mfr # JX-B0520A-1-B ) VA-FC-1M-BKW Accessory - Flat USB A to Micro B Cable 1M- Black and White VA-FC-1M-BLW Accessory - Flat USB A to Micro B Cable 1M- Blue and White VA-FC-STYLUS1 Accessory - Resistive Touch Screen Pen Stylus Table 1.1 VM800P & Accessory Ordering Information 1 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 Table of Contents 1 Ordering Information ...................................................................................................................... 1 2 Hardware Description ..................................................................................................................... 4 2.1 2.1.1 Dimensions...................................................................................................................... 5 2.1.2 Connectors and Jumpers................................................................................................. 6 2.1.3 CN1 - 2-pin power connector .......................................................................................... 6 2.1.4 CN2 – Micro USB Receptacle .......................................................................................... 7 2.1.5 J2 – Audio Selection ........................................................................................................ 7 2.1.6 J5 – Expansion Connector for I/O Daughter Card ........................................................... 7 2.1.7 J6 - Expansion Connector for Comm Daughter Card ...................................................... 9 2.1.8 JP1 – Audio Amplifier Power Selection ........................................................................... 9 2.1.9 SW1 – Power Source Selection ..................................................................................... 10 2.1.10 JP4 – USB Power Selection ............................................................................................ 10 2.2 3 5 6 7 Board Schematics .................................................................................................................. 11 Hardware Setup Guide .................................................................................................................. 14 3.1 4 Physical Description ................................................................................................................ 5 Power Configuration ............................................................................................................. 14 Arduino® Setup .............................................................................................................................. 15 4.1 Hardware Setup .................................................................................................................... 15 4.2 Software Setup...................................................................................................................... 15 Assembling the Bezel and Panel Mounting .................................................................................. 18 5.1 Dimensions for 3.5” Bezel ..................................................................................................... 19 5.2 Dimensions for 4.3” Bezel ..................................................................................................... 20 5.3 Dimensions for 5.0” Bezel ..................................................................................................... 21 Specifications ................................................................................................................................ 22 6.1 LCD Optical Specifications for 3.5” Panel.............................................................................. 22 6.2 LCD Optical Specifications for 4.3” Panel.............................................................................. 23 6.3 LCD Optical Specifications for 5.0” Panel.............................................................................. 24 Contact Information...................................................................................................................... 25 Appendix A – References ...................................................................................................................... 26 2 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 Document References....................................................................................................................... 26 Acronyms and Abbreviations ............................................................................................................ 26 Appendix B – List of Tables & Figures ................................................................................................... 27 List of Tables ..................................................................................................................................... 27 List of Figures .................................................................................................................................... 27 Appendix C – Revision History .............................................................................................................. 28 3 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 2 Hardware Description Figure 2.1 VM800P35A Module Profile 3.5" Display Version Figure 2.2 VM800P43A Module Profile 4.3" Display Version Figure 2.3 VM800P50A Module Profile 5.0" Display Version NOTE: The above modules are also available with pearl coloured bezels. The VM800P module is available for different LCD sizes: 3.5”, 4.3” or 5”. Each VM800P module is assembled with following parts: VM800PxxA PCB board LCD panel with touch screen Bezel The main functions of the VM800PxxA PCB board are as follows: FT800 EVE for graphic, audio and touch control ATMEGA328P microcontroller operating at 5V and 16MHz, controlling the FT800 and other peripheral interfaces 3 stage audio filter 8Ω micro speaker to work with on-board audio amplifier Jumper selection allowing audio line out option LCD backlight LED driver Real Time Clock(RTC) with button battery 4 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 USB interface for power supply and firmware programming 2-pin JST connector for alternative power source 3.3V regulator: takes 5V input and outputs 3.3V for on-board circuits 2x Micro-MaTch miniature connectors for various daughter card expansion SD Card Socket (4GByte card supplied with module) 2.1 Physical Description The VM800P module dimensions are illustrated in Figure 2.4 and Figure 2.5. 2.1.1 Dimensions 46.2 7.8 4 59.6 5 72.5 76.3 Figure 2.4 VM800P35A Dimensions (Top view) 5 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 61.6 23.2 68.5 64.5 5 4 102.8 106.5 Figure 2.5 VM800P43A/VM800P50A Dimensions (Top view) ±0.50mm Tolerance All dimensions are in mm 2.1.2 Connectors and Jumpers Connectors and jumpers are described in the following sections. 2.1.3 CN1 - 2-pin power connector Pin No. Name Type Description 1 VCC P 5V DC power supply 2 GND P Ground Table 2.1 CN1 - Power Pin-out 6 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 2.1.4 Clearance No.: FTDI# 385 CN2 – Micro USB Receptacle Pin No. Name Type Description 1 VBUS P 5V power supply 2 D- IO USB D- line 3 D+ IO USB D+ line 4 NC NA No connection 5 GND P Ground Table 2.2 CN2 – Micro USB Pin-out 2.1.5 J2 – Audio Selection Select between audio line-out or connection to the power amplifier. Jumper position Description Short pin 1-2 Audio amp enabled (default) Short pin 2-3 Audio amp mute, Audio lineout on pin 1 Table 2.3 J2 – Audio Options 2.1.6 J5 – Expansion Connector for I/O Daughter Card This 16-pin Micro-MaTch miniature connector provides ATmega328P SPI/I2C/IO control to the daughter card. 5V and 3.3V power supplies are also available. Pin No. Name Type Description 1 SCK O SPI Clock output 2 MOSI O SPI Master Out Slave in 3 MISO I SPI Master In Slave out 4 IO7 O SPI slave select 5 INT0 I Interrupt input from DC 6 IO6 O Active LOW reset output to DC 7 AD4 IO I2C SDA data input/output 8 AD5 O I2C SCL clock output 9 3V3 P 3.3V power supply to DC 10 5V P 5V power supply to DC 11 GND P Ground 7 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Pin No. Name Type 12 RST# O System reset output 13 IO5 IO GPIO 14 AD0 IO GPIO 15 AD7 AI ADC input 16 AD6 AI ADC input Clearance No.: FTDI# 385 Description Table 2.4 J5 - I/O Expansion Connector Pin-out 8 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 2.1.7 Clearance No.: FTDI# 385 J6 - Expansion Connector for Comm Daughter Card This 16-pin Micro MaTch Miniature connector provides ATmega328P SPI/I2C/IO control to the daughter card. 5V and 3.3V power supplies are also available. Pin No. Name Type Description 1 SCK O SPI Clock output 2 MOSI O SPI Master Out Slave in 3 MISO I SPI Master In Slave out 4 SS O SPI salve select 5 INT0 I Interrupt input from DC 6 IO6 O Active LOW reset output to DC 7 AD4 IO I2C SDA data input/output 8 AD5 O I2C SCL clock output 9 3V3 P 3.3V power supply to DC 10 5V P 5V power supply to DC 11 GND P Ground 12 RST# O System reset output 13 AD1 IO GPIO 14 IO4 IO GPIO 15 AD3 AI GPIO 16 AD2 AI GPIO Table 2.5 J5 - Communication Expansion Connector Pin-out 2.1.8 JP1 – Audio Amplifier Power Selection This jumper provides the option to select the power supply voltage for the on-board power amplifier. Jumper position Description Short pin 1-2 3.3V selected (default) Short pin 2-3 5V selected Table 2.6 JP1 - Audio Amplifier Power Pin Options NOTE: This needs to be configured before audio can be heard. Default is 3.3V. Select 5V to increase the maximum volume for the speaker. 9 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 2.1.9 Clearance No.: FTDI# 385 SW1 – Power Source Selection Jumper position Description Short pin 1-2 Board power from CN1 Short pin 2-3 Board power from CN2 (default) Table 2.7 SW1 - Power Source Selection 2.1.10 JP4 – USB Power Selection Jumper position Description Open Enable USB power to application circuits when FT232R is enumerated (Default). USB power will be turned off during USB suspend Short USB power always enabled Table 2.8 JP4 - USB Power Selection 10 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 2.2 Board Schematics Figure 2.6 VM800P35A FT800 and LCD Interface 11 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 Figure 2.7 VM800P43A/VM800P50A FT800 and LCD Interface Figure 2.8 VM800PxxA MCU, USB and I/O 12 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 Figure 2.9 VM800PxxA SD-Card, Flash and RTC Figure 2.10 VM800PxxA Audio 13 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 3 Hardware Setup Guide 3.1 Power Configuration There are 2 methods of powering the VM800P board. 1) USB Power(5V) - Connect USB power through micro-USB cable to CN2 2) DC IN(5V) - Connect 5V to CN1 The following table summarizes how to power the VM800P board using the various methods. Power Method CN1 CN2 USB Power N/C 5V DC IN(5V) 5V 5V SW1 Short pin 2-3 (default) Short pin 1-2 Table 3.1 Board Power Configuration 14 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 4 Arduino® Setup FTDI provides sample source code, sample application notes and a ready to run demo based on the Arduino® platform. Detailed information can be found at: http://www.ftdichip.com/Support/Documents/AppNotes/AN_318_Arduino_Library_for_FT800_Seri es.pdf http://www.ftdichip.com/Support/Documents/AppNotes/AN_275_FT800_Example_with_Arduino.pd f http://www.ftdichip.com/Support/Documents/AppNotes/AN_246%20VM800CB_SampleApp_Arduin o_Introduction.pdf 4.1 Hardware Setup Connect a USB cable (suggest FTDI accessory VA-FC-1M-BKW or VA-FC-1M-BLW) from the VM800P USB port CN2 to the PC USB host port or self-powered hub port. The PC will supply power to the VM800P after the FTDI FT232R driver is properly loaded and the USB host completes USB device configuration. 4.2 Software Setup The arduino code can be downloaded from the Arduino IDE to the ATMEGA328P through the USB connector CN2 connected to the PC. The USB connector CN2 is also used to display debug output from the ATMEGA328P to the PC terminal application. Default sample code is downloaded to the ATMEGA328P during the VM800P module manufacturing. When the VM800P is connected to the PC through the USB connector CN2, the VM800P is powered up and the sample code is functional with the demo applications. Download the Arduino IDE from http://arduino.cc/en/main/software. Install the Arduino IDE Open the Arduino IDE Open the FT800 sample project to be downloaded to the VM800P (Examples are available from: http://www.ftdichip.com/Support/SoftwareExamples/FT800_Projects.htm Or you may have developed your own code) Select the Tools->Board-> Arduino Pro or Pro Mini(5V, 16MHz) w/ATmega328 as shown in Fig 4.1. Select the Tools->Serial Port->COMxx corresponding to the VM800P as shown in Fig 4.2. Click the Upload button as shown in Fig 4.3. This will upload the FT800 sample to the VM800P. 15 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 Figure 4.1 Select Board Figure 4.2 Select Serial Port (NOTE: Your device may not be COM22 as shown. Select the COM port you have installed) 16 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 Figure 4.3 Click Upload Button 17 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 5 Assembling the Bezel and Panel Mounting Figure 5.1 VM800P Panel Mount (Front view) Figure 5.2 VM800P Panel Mount (Rear view) 18 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 5.1 Dimensions for 3.5” Bezel Figure 5.3 VM800P 3.5” panel mount dimensions 19 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 5.2 Dimensions for 4.3” Bezel Figure 5.4 VM800P 4.3” panel mount dimensions 20 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 5.3 Dimensions for 5.0” Bezel Figure 5.5 VM800P 5.0” panel mount dimensions 21 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 6 Specifications 6.1 LCD Optical Specifications for 3.5” Panel Figure 6.1 3.5” TFT Optical Specifications 22 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 6.2 LCD Optical Specifications for 4.3” Panel Figure 6.2 4.3” TFT Optical Specifications 23 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 6.3 LCD Optical Specifications for 5.0” Panel Figure 6.3 5.0" TFT Optical Specifications 24 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 7 Contact Information Head Office – Glasgow, UK Branch Office – Tigard, Oregon, USA Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 Future Technology Devices International Limited (USA) 7130 SW Fir Loop Tigard, OR 97223-8160 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) [email protected] [email protected] [email protected] E-Mail (Sales) E-Mail (Support) E-Mail (General Enquiries) [email protected] [email protected] [email protected] Branch Office – Taipei, Taiwan Branch Office – Shanghai, China Future Technology Devices International Limited (Taiwan) 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8791 3570 Fax: +886 (0) 2 8791 3576 Future Technology Devices International Limited (China) Room 1103, No. 666 West Huaihai Road, Shanghai, 200052 China Tel: +86 21 62351596 Fax: +86 21 62351595 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) E-mail (Sales) E-mail (Support) E-mail (General Enquiries) [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] Web Site http://ftdichip.com System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performance requirements. All application-related information in this document (including application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640 25 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 Appendix A – References Document References For module documentations, please refer to URL below: http://www.ftdichip.com/Products/modules/VM800P.html FT800 datasheet: DS_FT800_Embedded_Video_Engine FT800 software programming guide: FT800_Programmer_Guide AN_318: Arduino Library for FT800 Series AN_275 : FT800 Example with Android AN_246: VM800CB SampleApp_Arduino Introduction Acronyms and Abbreviations Terms Description IO Input Output I2C Inter Integrated Circuit LCD Liquid Crystal Display RTC Real Time Clock SD CARD SPI UART USB USB-IF Secure Digital Card Serial Peripheral Interface Universal Asynchronous Receiver Transmitter Universal Serial Bus USB Implementers Forum 26 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 Appendix B – List of Tables & Figures List of Tables Table 1.1 VM800P & Accessory Ordering Information ............................................................... 1 Table 2.1 CN1 - Power Pin-out .............................................................................................. 6 Table 2.2 CN2 – Micro USB Pin-out........................................................................................ 7 Table 2.3 J2 – Audio Options ................................................................................................ 7 Table 2.4 J5 - I/O Expansion Connector Pin-out ...................................................................... 8 Table 2.5 J5 - Communication Expansion Connector Pin-out ..................................................... 9 Table 2.6 JP1 - Audio Amplifier Power Pin Options ................................................................... 9 Table 2.7 SW1 - Power Source Selection .............................................................................. 10 Table 2.8 JP4 - USB Power Selection ................................................................................... 10 Table 3.1 Board Power Configuration ................................................................................... 14 List of Figures Figure 2.1 VM800P35A Module Profile 3.5" Display Version ....................................................... 4 Figure 2.2 VM800P43A Module Profile 4.3" Display Version ....................................................... 4 Figure 2.3 VM800P50A Module Profile 5.0" Display Version ....................................................... 4 Figure 2.4 VM800P35A Dimensions (Top view) ....................................................................... 5 Figure 2.5 VM800P43A/VM800P50A Dimensions (Top view)...................................................... 6 Figure 2.6 VM800P35A FT800 and LCD Interface ................................................................... 11 Figure 2.7 VM800P43A/VM800P50A FT800 and LCD Interface ................................................. 12 Figure 2.8 VM800PxxA MCU, USB and I/O ............................................................................ 12 Figure 2.9 VM800PxxA SD-Card, Flash and RTC .................................................................... 13 Figure 2.10 VM800PxxA Audio ............................................................................................ 13 Figure 4.1 Select Board ..................................................................................................... 16 Figure 4.2 Select Serial Port ............................................................................................... 16 Figure 4.3 Click Upload Button ............................................................................................ 17 Figure 5.1 VM800P Panel Mount (Front view) ........................................................................ 18 Figure 5.2 VM800P Panel Mount (Rear view) ......................................................................... 18 Figure 5.3 VM800P 3.5” panel mount dimensions .................................................................. 19 Figure 5.4 VM800P 4.3” panel mount dimensions .................................................................. 20 Figure 5.5 VM800P 5.0” panel mount dimensions .................................................................. 21 Figure 6.1 3.5” TFT Optical Specifications ............................................................................. 22 Figure 6.2 4.3” TFT Optical Specifications ............................................................................. 23 Figure 6.3 5.0" TFT Optical Specifications ............................................................................. 24 27 Copyright © 2014 Future Technology Devices International Limited VM800P Embedded Video Engine Plus Module Datasheet Version 1.2 Document Reference No.: FT_000989 Clearance No.: FTDI# 385 Appendix C – Revision History Document Title: VM800P Embedded Video Engine Plus Module Datasheet Document Reference No.: FT_000989 Clearance No.: FTDI# 385 Product Page: http://www.ftdichip.com/EVE.htm Document Feedback: Send Feedback Revision Changes Date 1.0 Initial Release 2014-04-24 1.1 Updated Release 2014-05-27 1.2 Updated the optical characteristics for the 4.3” and 5” displays 2014-06-12 28 Copyright © 2014 Future Technology Devices International Limited