SE5003L - Skyworks Solutions, Inc.

DATA SHEET
SE5003L: 5 GHz, 23dBm Power Amplifier with Power Detector
Applications
Product Description



The SE5003L is a 5GHz power amplifier offering high
linear power for wireless LAN applications. The
SE5003L incorporates a power detector for closed
loop monitoring and control of the output power.
DSSS 5 GHz WLAN (IEEE802.11a)
DSSS 5 GHz WLAN (IEEE802.11n)
Access Points, PCMCIA, PC cards
Features







High output power amplifier
- 23dBm at 5V
External Analog Reference Voltage (VREF) for
maximum flexibility
Buffered, temperature compensated power
detector
3% EVM, @23dBm, 64 QAM, 54 Mbps
32 dB Gain
Lead Free, RoHS compliant and halogen free
package, MSL3
20 pin 4 mm x 4 mm x 0.9 mm QFN
Ordering Information
Part Number
Package
Remark
SE5003L
SE5003L-R
SE5003L-EK1
20 Pin QFN
20 Pin QFN
Evaluation Kit
Samples
Tape and Reel
Standard
The SE5003L offers high integration for a simplified
design, providing quicker time to market and higher
application board production yield.
The device
integrates the input match, the inter-stage match, the
output match, the power detector with 15dB of
dynamic range and a 3.8GHz notch filter. Only 6
external decoupling capacitors are required to
complete the design.
For wireless LAN applications, the device meets the
requirements of IEEE802.11a & 802.11n, and delivers
approximately 23dBm of linear output power at 5V.
The SE5003L integrates the reference voltage
generator. A 2.85V reference voltage on VREF is all
that is required to enable or disable the power
amplifier.
Functional Block Diagram
RFIN includes DC shunt to Ground; External blocking capacitor is recommended.
Figure 1: Functional Block Diagram
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202392B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
1
DATA SHEET
SE5003L: 5 GHz, 23dBm Power Amplifier with Power Detector
Pin Out Diagram
GND
GND
VCC3
VCC2
VCC1
20 19 18 17 16
NU 1
15 GND
GND 2
14 GND
RF IN 3
13 RF OUT
GND 4
12 GND
VREF 5
11 GND
6
7
8
9
10
SP1
SP2
VCC2
VCC3
DET
Figure 2: SE5003L Pin Out (Top View Through Package)
Pin Out Description
Pin No.
Name
Description
1
NU
2
GND
Ground
3
RFin
Power Amplifier RF input, DC block required
4
GND
Ground
5
VREF
Reference Voltage
6
SP1
7
SP2
8
VCC2
Second Stage Supply Voltage
9
VCC3
Third Stage Supply Voltage
10
DET
Analog Power Detector Output
11,12
GND
Ground
13
RF OUT
14-17
GND
Ground
18
VCC3
Third Stage Supply Voltage
19
VCC2
Second Stage Supply Voltage
20
VCC1
First Stage Supply Voltage
Pin is Not Used, and is open circuit in the package
Ports for optional capacitor to improve dynamic EVM
Power Amplifier RF Output
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202392B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
2
DATA SHEET
SE5003L: 5 GHz, 23dBm Power Amplifier with Power Detector
Absolute Maximum Ratings
These are stress ratings only. Exposure to stresses beyond these maximum ratings for a long period of time may
cause permanent damage to, or affect the reliability of the device. Avoid operating the device outside the
recommended operating conditions defined below. This device is ESD sensitive. Handling and assembly of this
device should be at ESD protected workstations.
Symbol
Definition
Min.
Max.
Unit
Supply Voltage on pins VCC3
-0.3
+6
Supply Voltage on pins VCC1, VCC2
-0.3
VCC3
VREF
Power Amplifier Enable and reference voltage
-0.3
3.6
V
RFIN
RF Input Power, RFout into 50Ω match, TCASE_MAX = 85C
-
6
dBm
TSTG
Storage Temperature Range
-40
160
°C
-
160
°C
VCC
Tj
ESD HBM
V
Maximum Junction Temperature
JEDEC JESD22-A114 all pins
Class1A
Recommended Operating Conditions
Symbol
VCC
TCASE_MAX
VREF
Parameter
Min.
Max.
Unit
Supply Voltage VCC1, VCC2, VCC3
3.0
5.5
V
Max Case Temperature
-40
85
°C
Reference Voltage
2.8
2.9
V
DC Electrical Characteristics
Conditions: VCC = 5.0V, VREF = 2.85 V, TA = 25 °C, as measured on Skyworks’ SE5003L-EK1 evaluation board,
unless otherwise noted.
Symbol
Parameter
ICC-802.11a
Supply Current
IQC
Conditions
Min.
Typ.
Max.
Unit
POUT = 23 dBm, 5.0V, 54 Mbps, 64 QAM
-
340
650
mA
Quiescent Current
No RF
-
150
-
mA
IOFF
Supply Current
VREF = 0 V, No RF
-
0.5
10
μA
IEN
Bias Control
Current
VREF = VREFH
Internal 2KΩ pull down resistor
-
10
-
mA
VREF H
Reference Voltage
Enabled
-
2.8
2.85
2.9
V
VREF L
Reference Voltage
Disabled
-
0
-
0.5
V
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202392B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
3
DATA SHEET
SE5003L: 5 GHz, 23dBm Power Amplifier with Power Detector
AC Electrical Characteristics
802.11a AC Electrical Characteristics
Conditions: VCC = 5.0 V, VREF = 2.85 V, f = 5.4 GHz, TA = 25 °C, as measured on Skyworks’ SE5003L-EK1
evaluation board, unless otherwise noted
Symbol
fL-U
Parameter
Conditions
Min.
Typ.
Max.
Unit
-
5.15
-
5.85
GHz
802.11a, 54Mbps, 64 QAM, 3% EVM
22
-
-
-
26
-
Frequency Range
POUT
Output Power
dBm
P1dB
Output 1dB
compression point
No modulation
28
32
-
dBm
S21
Small Signal Gain
PIN = -25 dBm
28
32
-
dB
ΔS21
Gain Variation
Withing each UNII Band
-
3
-
dB
ΔS21 3.8
Gain at 3.8GHz
PIN = -25 dBm
-
-
0
dB
Harmonic
POUT = 23 dBm, 5V
-
-45
-
dBm/MHz
-
-
0.5
-
us
802.11n, MCS0, Mask Compliant
2f
3f
tr , tf
STAB
Rugged
Rise and Fall Time
Stability
POUT = 23 dBm, VCC = 5V, 54 Mbps,
64 QAM, VSWR = 6:1, all phases
Tolerance to
constant input
power into a
mismatch load
PIN = -10dBm, CW,
VSWR = 6:1, all phases
All non-harmonically related outputs
less than -50 dBc/100 kHz
No damage
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202392B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
4
DATA SHEET
SE5003L: 5 GHz, 23dBm Power Amplifier with Power Detector
Power Detector
Conditions: VCC = 5.0 V, VREF = 2.85 V, f = 5.4 GHz, TA = 25 °C, as measured on Skyworks’ SE5003L-EK1
evaluation board, unless otherwise noted
Symbol
Parameter
PDR
POUT detect range
VDET
Detector voltage
ERRDET
Conditions
Min.
Typ.
-
0
-
P1dB
dBm
POUT = 23 dBm
-
1.00
-
V
POUT = NO RF
-
0.35
-
V
-0.5
-0.5
-
+0.5
+0.5
dB
+1.5
dB
△POUT at constant VDET,
5.15 GHz – 5.70 GHz
5.70 GHz – 5.85 GHz
Detector Accuracy
△POUT at constant VDET,
VSWR = 3:1
-1.5
Max.
Unit
PDZOUT
Output Impedance
-
-
700
-
Ω
PDZLOAD
DC load impedance
-
-
26.5
-
KΩ
Power Detector Response
5400
5650
VDET (V)
5150
5750
5850
1.6
1.4
1.2
1
0.8
0.6
0.4
0.2
0
10
12
14
16
18
20
22
Output Power (dBm)
24
26
28
Figure 3: SE5003L Power Detector Characteristic over Frequency
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202392B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
5
DATA SHEET
SE5003L: 5 GHz, 23dBm Power Amplifier with Power Detector
Package Diagram
20
19
18
17
16
16
17
18
19
20
1
15
15
1
2
14
14
2
3
13
13
3
4
12
12
4
5
11
11
5
6
7
8
9
10
10
TOP SIDE
9
8
7
6
BOTTOM SIDE
Figure 4: SE5003L Package Information
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202392B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
6
DATA SHEET
SE5003L: 5 GHz, 23dBm Power Amplifier with Power Detector
Recommended Land and Solder Pattern
20
19
18
17
20
16
19
18
17
20
16
19
18
17
16
1
15
1
15
1
15
2
14
2
14
2
14
3
13
3
13
3
13
4
12
4
12
4
12
5
11
5
11
5
11
6
7
8
9
10
6
7
8
9
10
6
7
8
9
10
Figure 5: SE5003L Recommended Land Pattern
Package Handling Information
Because of its sensitivity to moisture absorption, instructions on the shipping container label must be followed
regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption
may occur when the part is subjected to high temperature during solder assembly. The SE5003L is capable of
withstanding a Pb free solder reflow. Care must be taken when attaching this product, whether it is done manually or
in a production solder reflow environment. If the part is manually attached, precaution should be taken to insure that
the device is not subjected to temperatures above its rated peak temperature for an extended period of time. For
details on both attachment techniques, precautions, and handling procedures recommended, please refer to:
 “Quad Flat No-Lead Module Solder Reflow & Rework Information”, Document Number QAD-00045
 “Handling, Packing, Shipping and Use of Moisture Sensitive QFN”, Document Number QAD-00044
Caution! Class 1B ESD sensitive device
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202392B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
7
DATA SHEET
SE5003L: 5 GHz, 23dBm Power Amplifier with Power Detector
Branding Information
Pin 1 Designator
Company Name
Pin 1
Terminal Finish
e3
Part Number
Lot Code
SiGe
2527L
5003L
Lot Code
Figure 6: SE5003L Branding Information
Tape and Reel Information
Parameter
Devices Per Reel
Reel Diameter
Tape Width
Value
3000
13 inches
12 millimeters
Figure 7: SE5003L-R Tape and Reel Information
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202392B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
8
DATA SHEET
SE5003L: 5 GHz, 23dBm Power Amplifier with Power Detector
Document Change History
Revision
Date
Notes
1.0
Aug 18, 2009
Created
1.1
Jan 12, 2010
Updated package pin out
1.2
May 25, 2010
Added Recommended Solder Land Pattern
Updated Power Detector Curve
Extend temperature range to -40 to +85
1.3
Aug 20, 2010
Updated IOFF Specification to 50uA max.
Updated Branding Information.
1.4
Feb 25, 2011
Updated Maximum Junction Temperature
Updated ESD rating
Updated Harmonic specifications
Added VREF min/max limits to recommended operating condition
1.5
Mar 28, 2012
Updated with Skyworks logo and disclaimer statement
1.6
Apr 12, 2012
Remove “Preliminary” from header
Added min/max limits to Gain, P1dB, EVM, ICC
1.7
May 31, 2012
Updated ESD rating
Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein,
are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or
omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time,
without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other
difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials,
products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in
Skyworks Terms and Conditions of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE,
INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL
SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR
OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT,
INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE
MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to
personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to
fully indemnify Skyworks for any damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or
operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks.
Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated
published specifications or parameters.
Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries.
Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions,
posted at www.skyworksinc.com, are incorporated by reference.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202392B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
9