DATA SHEET SE2565T: 2.4 GHz High Power Wireless LAN Power Amplifier Applications Product Description The SE2565T is a high power 802.11bgn WLAN power amplifier module providing the functionality of the power amplifier, power detector, reference voltage generator and input match. IEEE802.11b DSSS WLAN IEEE802.11g,n OFDM WLAN High Power Wireless Networking Products Features The SE2565T is designed for ease of use and maximum flexibility, with an integrated input match, and external output match to adjust the load line for either 3.3V, 23dBm operation. Dual Mode IEEE802.11b, IEEE802.11g, IEEE802.11n 23 dBm, EVM = 3%, 802.11g, OFDM 54 Mbps 26 dBm, ACPR < -32 dBc, 802.11b Integrated PA, Input Match, 2.8V reference voltage generator Integrated Temperature Compensated, Positive Slope Power Detector Pb-free, RoHS compliant and Halogen-free 3 mm x 3 mm x 0.6 mm QFN, MSL 3 The SE2565T includes a temperature compensated transmit power detector with over 20 dB of dynamic range and <1.2dB variation under 3:1 mismatch at the antenna. The SE2565T includes a digital enable control due to an integrated reference voltage generator. The power ramp rise/fall time is 0.5 μs typical. Ordering Information Part No. Package Remark SE2565T SE2565T-R SE2565T-EK1 16 pin QFN 16 pin QFN N/A Samples Tape & Reel Evaluation kit Functional Block Diagram EN VCC0 VCC1 VCC2 Bias & Control RFIN RFOUT 50Ω DET DET Figure 1: Functional Block Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202424A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 1 DATA SHEET SE2565T: 2.4 GHz High Power Wireless LAN Power Amplifier Pin Out Diagram VCC2 RF IN 1 NC VCC1 16 15 14 13 12 GND Ground Paddle EN 2 11 RF OUT GND 3 10 RF OUT VCC0 4 9 5 6 7 GND 8 NC DET GND GND Figure 2: SE2565T Pin Out (Top View Through Package) Pin Out Description Pin No. Name Description 1 RF IN 2 EN 3 GND Ground 4 VCC0 Power Supply for Bias Circuit 5 GND Ground 6 GND Ground 7 DET Power Detector Output 8 NC No Connect. May be left floating or grounded. RF Input Power Amplifier Enable 9 GND 10 RF OUT Ground RF Output 11 RF OUT RF Output 12 GND Ground 13 VCC2 Power Supply for 2 14 NC 15 VCC1 Power Supply driver stages 16 GND Ground Die paddle GND Ground nd Stage No Connect. May be left floating or grounded. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202424A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 2 DATA SHEET SE2565T: 2.4 GHz High Power Wireless LAN Power Amplifier Absolute Maximum Ratings These are stress ratings only. Exposure to stresses beyond these maximum ratings may cause permanent damage to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions defined below. This device is ESD sensitive. Handling and assembly of this device should be at ESD protected workstations. Symbol Min. Max. Unit Supply Voltage on VCC -0.3 4.0 V VIN DC input on EN -0.3 3.6 V TX RF Input Power with RF Out terminated in 50Ω - 12.0 dBm TA Operating Temperature Range -40 85 °C Storage Temperature Range -40 150 °C - 1,000 V VCC TSTG ESD HBM Definition JEDEC JESD22-A114 all pins Recommended Operating Conditions Symbol TA VCC Parameter Min. Typ. Max. Unit Ambient temperature -40 25 85 °C Supply voltage, relative to GND = 0 V 2.9 3.3 3.6 V DC Electrical Characteristics Conditions: VCC = EN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2565T-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted Symbol Parameter Conditions Min. Typ. Max. Unit ICC-G Total Supply Current POUT = 23 dBm, 54 Mbps OFDM signal, 64QAM - 410 - mA ICC-B Total Supply Current POUT = 26 dBm, 11 Mbps CCK signal, BT = 0.45 - 450 - mA ICC_OFF Total Supply Current EN = 0 V, No RF Applied - 10 100 μA Logic Characteristics Conditions: VCC = EN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2565T-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit VENH Logic High Voltage (Module On) - 1.8 - VCC V VENL Logic Low Voltage (Module Off) - 0 - 0.4 V IENH Input Current Logic High Voltage - - 300 - μA IENL Input Current Logic Low Voltage VENL= 0.4V - 1 50 μA Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202424A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 3 DATA SHEET SE2565T: 2.4 GHz High Power Wireless LAN Power Amplifier Symbol ZEN Parameter Conditions Enable pin input impedance Min. Passive Pull Down Typ. Max. Unit 10 kΩ AC Electrical Characteristics 802.11g/n Transmit Characteristics Conditions: VCC = EN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2565T-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FIN POUT Parameter Frequency Range Output Power Condition Min. Typ. Max. - 2400 - 2500 54 Mbps OFDM signal, 64 QAM, 3% EVM - 23 - 11Mbps CCK signal, BT = 0.045, Mask - 26 - 802.11n, HT20, all data rates, Mask - 27 - 802.11n, HT40, All data rates, Mask - 24 - Unit MHz dBm P1dB P1dB - - 30 - dBm S21 Small Signal Gain - 30 32 - dB Small Signal Gain Variation Gain variation over single 40MHz channel Gain Variation over band - 0.5 - ΔS21 - 1.0 - POUT = 26 dBm, 1 Mbps, 802.11b - -50 -45 dBm/MHz Harmonics - -50 -45 dBm/MHz - 0.5 - μs 10 15 - dB 2f 3f tdr, tdf Delay and rise/fall Time S11 Input Return Loss STAB RU 50 % of VEN edge and 90/10 % of final output power level - dB Stability CW, POUT = 26 dBm 0.1 GHz – 20 GHz Load VSWR = 6:1 All non-harmonically related outputs less than -42 dBm/MHz Ruggedness CW, PIN = +12dBm, Load VSWR = 6:1 No permanent damage. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202424A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 4 DATA SHEET SE2565T: 2.4 GHz High Power Wireless LAN Power Amplifier Power Detector Characteristics Conditions: VCC = EN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2565T-EV1 evaluation board, unless otherwise noted. Symbol Parameter FOUT Frequency Range PDR Power detect range, CW Condition Min. Typ. - 2400 - 2500 MHz 0 - 26 dBm Measured at RF out Max. Unit DC source impedance on PD_OUT - - 2.3 - KΩ PDZLOAD DC load impedance - - 26.5 - KΩ PDVNoRF Output Voltage, POUT = 5dBm Measured into 26.5KΩ - 0.33 - V PDVp23 Output Voltage, POUT = 23 dBm CW Measured into 26.5KΩ - 0.70 - V PDVp27 Output Voltage, POUT = 27 dBm CW Measured into 26.5KΩ - 0.97 - V LPF-3dB Power detect low pass filter -3dB corner frequency Measured into 26.5KΩ - 2.0 - MHz PDZsrc Figure 3: SE2565T Detector Characteristics Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202424A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 5 DATA SHEET SE2565T: 2.4 GHz High Power Wireless LAN Power Amplifier Package Diagram 16 15 14 13 13 14 15 16 1 12 12 1 2 11 11 2 3 10 10 3 4 9 9 4 5 6 7 8 8 TOP VIEW 7 6 5 BOTTOM VIEW Figure 4: SE2565T Package Diagram Recommended Land and Solder Patterns Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202424A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 6 DATA SHEET SE2565T: 2.4 GHz High Power Wireless LAN Power Amplifier Figure 5: SE2565T Recommended Land and Solder Pattern Package Handling Information Because of its sensitivity to moisture absorption, instructions on the shipping container label must be followed regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SE2565T is capable of withstanding a Pb free solder reflow. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. If the part is manually attached, precaution should be taken to insure that the device is not subjected to temperatures above its rated peak temperature for an extended period of time. For details on both attachment techniques, precautions, and handling procedures recommended, please refer to: “Quad Flat No-Lead Module Solder Reflow & Rework Information”, Document Number QAD-00045 “Handling, Packing, Shipping and Use of Moisture Sensitive QFN”, Document Number QAD-00044 Caution! Class 1C ESD sensitive device Branding Information SiGe 2565T Lot Code Figure 6: SE2565T Branding Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202424A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 7 DATA SHEET SE2565T: 2.4 GHz High Power Wireless LAN Power Amplifier Tape and Reel Information Parameter Devices Per Reel Reel Diameter Tape Width Value 3000 13 inches 12 millimeters Figure 7: SE2565T-R Tape and Reel Information Document Change History Revision Date Notes 1.0 Oct 20, 2008 Created 1.1 Dec 19, 2008 Changed pin configuration 1.2 Jan 28, 2009 Updated recommended operating conditions and total current consumption 1.3 May 8, 2009 Updated Package Outline Drawing Updated PA Logic Characteristics 1.4 Jul 8, 2009 Updated to correct pins 8 & 14 definitions. 1.5 Aug 2, 2009 Updated detector characteristics 1.6 Aug 13, 2009 Updated detector characteristics 1.7 Jan 25, 2010 Updated Off State Leakage Updated Detector Characteristics 1.8 Jun 24, 2010 Updated operating temperature range Updated ESD rating to Class 1C 1.9 Dec 18, 2010 Added OFDM Mask Compliance 2.0 Apr 02, 2012 Updated with Skyworks logo and disclaimer statement Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202424A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 8 DATA SHEET SE2565T: 2.4 GHz High Power Wireless LAN Power Amplifier opyright © 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202424A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 9